Table of Contents

Related Documents

61-S-MLAG Configuration Examples

Title	Size	Download
61-S-MLAG Configuration Examples	124.59 KB

Introduction

This document provides configuration examples for using simple multichassis link aggregation (S-MLAG).

S-MLAG enhances dynamic link aggregation to establish an aggregation that spans multiple standalone devices to a remote device.

Prerequisites

The configuration examples were created and verified in a lab environment, and all the devices were started with the factory default configuration. When you are working on a live network, make sure you understand the potential impact of every command on your network.

The following information is provided based on the assumption that you have basic knowledge of S-MLAG.

Example: Configuring S-MLAG

Network configuration

Device B, Device C, and Device D are standalone devices. As shown in Figure 1, configure Device B, Device C, and Device D as S-MLAG devices to establish a multidevice aggregate link with Device A.

Figure 1 Network diagram

Analysis

To establish a multidevice aggregate link with Device A, you must perform the following tasks on Device B, Device C, and Device D:

1. Create a Layer 2 dynamic aggregate interface and assign GigabitEthernet 1/0/1 to its aggregation group.

2. Assign the aggregate interfaces to the same DR group.

Applicable hardware and software versions

The following matrix shows the hardware and software versions to which this configuration example is applicable:

Hardware	Software version
S6812 switch series S6813 switch series	Release 66xx
S6550XE-HI switch series	Release 6008 and later
S6525XE-HI switch series	Release 6008 and later
S5850 switch series	Release 8005 and later
S5570S-EI switch series	Release 11xx
S5560X-EI switch series	Release 63xx, Release 65xx, Release 66xx
S5560X-HI switch series	Release 63xx, Release 65xx, Release 66xx
S5500V2-EI switch series	Release 63xx, Release 65xx, Release 66xx
MS4520V2-30F switch	Release 63xx, Release 65xx, Release 66xx
MS4520V2-30C switch MS4520V2-54C switch	Release 65xx, Release 66xx
MS4520V2-28S switch MS4520V2-24TP switch	Release 63xx
S6520X-HI switch series S6520X-EI switch series	Release 63xx, Release 65xx, Release 66xx
S6520X-SI switch series S6520-SI switch series	Release 63xx, Release 65xx, Release 66xx
S5000-EI switch series	Release 63xx, Release 65xx, Release 66xx
MS4600 switch series	Release 63xx, Release 65xx, Release 66xx
ES5500 switch series	Release 63xx, Release 65xx, Release 66xx
S5560S-EI switch series S5560S-SI switch series	Release 63xx
S5500V3-24P-SI switch S5500V3-48P-SI switch	Release 63xx
S5500V3-SI switch series (except S5500V3-24P-SI and S5500V3-48P-SI)	Release 11xx
S5170-EI switch series	Release 11xx
S5130S-HI switch series S5130S-EI switch series S5130S-SI switch series S5130S-LI switch series	Release 63xx
S5120V2-SI switch series S5120V2-LI switch series	Release 63xx
S5120V3-EI switch series	Release 11xx
S5120V3-36F-SI S5120V3-28P-HPWR-SI S5120V3-54P-PWR-SI	Release 11xx
S5120V3-SI switch series (except S5120V3-36F-SI, S5120V3-28P-HPWR-SI, and S5120V3-54P-PWR-SI)	Release 63xx
S5120V3-LI switch series	Release 63xx
S3600V3-EI switch series	Release 11xx
S3600V3-SI switch series	Release 11xx
S5120V3-EI switch series	Release 11xx
S3100V3-EI switch series S3100V3-SI switch series	Release 63xx
S5110V2 switch series	Release 63xx
S5110V2-SI switch series	Release 63xx
S5000V3-EI switch series S5000V5-EI switch series	Release 63xx
S5000E-X switch series S5000X-EI switch series	Release 63xx
E128C switch E152C switch E500C switch series E500D switch series	Release 63xx
MS4320V2 switch series MS4320V3 switch series MS4300V2 switch series MS4320 switch series MS4200 switch series	Release 63xx
WS5850-WiNet switch series	Release 63xx
WS5820-WiNet switch series WS5810-WiNet switch series	Release 63xx
WAS6000 switch series	Release 63xx
IE4300-12P-AC switch IE4300-12P-PWR switch IE4300-M switch series IE4320 switch series	Release 63xx

Restrictions and guidelines

Before you assign an interface to an aggregation group, use the display this command in interface view to identify whether attribute settings exist, including port isolation, QinQ, VLAN, and VLAN mapping settings. If attribute settings exist, use the corresponding undo commands to remove them.

Configure the link aggregation settings other than S-MLAG settings on each S-MLAG device. Make sure the settings are consistent across the S-MLAG devices.

As a best practice, maintain consistency across S-MLAG devices in service feature configuration.

Procedures

Configuring Device A

# Create Layer 2 aggregate interface Bridge-Aggregation 10, and set the link aggregation mode to dynamic.

<DeviceA> system-view

[DeviceA] interface bridge-aggregation 10

[DeviceA-Bridge-Aggregation10] link-aggregation mode dynamic

[DeviceA-Bridge-Aggregation10] quit

# Assign GigabitEthernet 1/0/1 through GigabitEthernet 1/0/3 to aggregation group 10.

[DeviceA] interface gigabitethernet 1/0/1

[DeviceA-GigabitEthernet1/0/1] port link-aggregation group 10

[DeviceA-GigabitEthernet1/0/1] quit

[DeviceA] interface gigabitethernet 1/0/2

[DeviceA-GigabitEthernet1/0/2] port link-aggregation group 10

[DeviceA-GigabitEthernet1/0/2] quit

[DeviceA] interface gigabitethernet 1/0/3

[DeviceA-GigabitEthernet1/0/3] port link-aggregation group 10

[DeviceA-GigabitEthernet1/0/3] quit

Configuring Device B

# Set the LACP system MAC address to 0001-0001-0001.

<DeviceB> system-view

[DeviceB] lacp system-mac 1-1-1

# Set the LACP system priority to 123.

[DeviceB] lacp system-priority 123

# Set the LACP system number to 1.

[DeviceB] lacp system-number 1

# Create Layer 2 aggregate interface Bridge-Aggregation 2, and set the link aggregation mode to dynamic.

[DeviceB] interface bridge-aggregation 2

[DeviceB-Bridge-Aggregation2] link-aggregation mode dynamic

# Assign Bridge-Aggregation 2 to S-MLAG group 100.

[DeviceB-Bridge-Aggregation2] port s-mlag group 100

[DeviceB-Bridge-Aggregation2] quit

# Assign GigabitEthernet 1/0/1 to aggregation group 2.

[DeviceB] interface gigabitethernet 1/0/1

[DeviceB-GigabitEthernet1/0/1] port link-aggregation group 2

[DeviceB-GigabitEthernet1/0/1] quit

Configuring Device C

# Set the LACP system MAC address to 0001-0001-0001.

<DeviceC> system-view

[DeviceC] lacp system-mac 1-1-1

# Set the LACP system priority to 123.

[DeviceC] lacp system-priority 123

# Set the LACP system number to 2.

[DeviceC] lacp system-number 2

# Create Layer 2 aggregate interface Bridge-Aggregation 3, and set the link aggregation mode to dynamic.

[DeviceC] interface bridge-aggregation 3

[DeviceC-Bridge-Aggregation3] link-aggregation mode dynamic

# Assign Bridge-Aggregation 3 to S-MLAG group 100.

[DeviceC-Bridge-Aggregation3] port s-mlag group 100

# Assign GigabitEthernet 1/0/1 to aggregation group 3.

[DeviceC] interface gigabitethernet 1/0/1

[DeviceC-GigabitEthernet1/0/1] port link-aggregation group 3

[DeviceC-GigabitEthernet1/0/1] quit

Configuring Device D

# Set the LACP system MAC address to 0001-0001-0001.

<DeviceD> system-view

[DeviceD] lacp system-mac 1-1-1

# Set the LACP system priority to 123.

[DeviceD] lacp system-priority 123

# Set the LACP system number to 3.

[DeviceD] lacp system-number 3

# Create Layer 2 aggregate interface Bridge-Aggregation 4, and set the link aggregation mode to dynamic.

[DeviceD] interface bridge-aggregation 4

[DeviceD-Bridge-Aggregation4] link-aggregation mode dynamic

# Assign Bridge-Aggregation 4 to S-MLAG group 100.

[DeviceD-Bridge-Aggregation4] port s-mlag group 100

# Assign GigabitEthernet 1/0/1 to aggregation group 4.

[DeviceD] interface gigabitethernet 1/0/1

[DeviceD-GigabitEthernet1/0/1] port link-aggregation group 4

[DeviceD-GigabitEthernet1/0/1] quit

Verifying the configuration

# Verify that GigabitEthernet 1/0/1 through GigabitEthernet 1/0/3 on Device A are Selected ports.

[DeviceA] display link-aggregation verbose

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port, M -- Management port, R -- Reference port

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

Aggregate Interface: Bridge-Aggregation10

Creation Mode: Manual

Aggregation Mode: Dynamic

Loadsharing Type: Shar

Management VLANs: None

System ID: 0x8000, a0c7-9afd-0100

Local:

Port Status Priority Index Oper-Key Flag

GE1/0/1 S 32768 1 1 {ACDEF}

GE1/0/2 S 32768 2 1 {ACDEF}

GE1/0/3 S 32768 3 1 {ACDEF}

Remote:

Actor Priority Index Oper-Key SystemID Flag

GE1/0/1(R) 32768 16385 50100 0x7b , 0001-0001-0001 {ACDEF}

GE1/0/2 32768 32769 50100 0x7b , 0001-0001-0001 {ACDEF}

GE1/0/3 32768 49153 50100 0x7b , 0001-0001-0001 {ACDEF}

Configuration files

IMPORTANT:

Support for the port link-mode bridge command depends on the device model.

· Device A:

interface Bridge-Aggregation10

link-aggregation mode dynamic

interface GigabitEthernet1/0/1

port link-mode bridge

combo enable fiber

port link-aggregation group 10

interface GigabitEthernet1/0/2

port link-mode bridge

combo enable fiber

port link-aggregation group 10

interface GigabitEthernet1/0/3

port link-mode bridge

combo enable fiber

port link-aggregation group 10

· Device B:

lacp system-mac 0001-0001-0001

lacp system-number 1

lacp system-priority 123

interface Bridge-Aggregation2

link-aggregation mode dynamic

port s-mlag group 100

interface GigabitEthernet1/0/1

port link-mode bridge

combo enable fiber

port link-aggregation group 2

· Device C:

lacp system-mac 0001-0001-0001

lacp system-number 2

lacp system-priority 123

interface Bridge-Aggregation3

link-aggregation mode dynamic

port s-mlag group 100

interface GigabitEthernet1/0/1

port link-mode bridge

combo enable fiber

port link-aggregation group 3

· Device D:

lacp system-mac 0001-0001-0001

lacp system-number 3

lacp system-priority 123

interface Bridge-Aggregation4

link-aggregation mode dynamic

port s-mlag group 100

interface GigabitEthernet1/0/1

port link-mode bridge

combo enable fiber

port link-aggregation group 4

Example: Aggregating server-side links by using S-MLAG

Network configuration

As shown in Figure 2, configure S-MLAG as follows:

· Connect GigabitEthernet 1/0/1 interfaces on Device A, Device B, and Device C to the server, and configure S-MLAG to aggregate the links to the server.

· Configure the server-facing aggregate interfaces on Device A, Device B, and Device C as edge aggregate interfaces for the aggregation member ports to forward traffic correctly before link aggregation is set up on the server.

Figure 2 Network diagram

Analysis

To create a multichassis aggregate link on Device A, Device B, and Device C, perform the following tasks:

· Create server-facing Layer 2 dynamic aggregate interfaces.

· Assign the aggregate interfaces to an S-MLAG group.

Applicable hardware and software versions

The following matrix shows the hardware and software versions to which this configuration example is applicable:

Hardware	Software version
S6812 switch series S6813 switch series	Release 66xx
S6550XE-HI switch series	Release 6008 and later
S6525XE-HI switch series	Release 6008 and later
S5850 switch series	Release 8005 and later
S5570S-EI switch series	Release 11xx
S5560X-EI switch series	Release 63xx , Release 65xx , Release 66xx
S5560X-HI switch series	Release 63xx , Release 65xx , Release 66xx
S5500V2-EI switch series	Release 63xx , Release 65xx , Release 66xx
MS4520V2-30F switch	Release 63xx , Release 65xx , Release 66xx
MS4520V2-30C switch MS4520V2-54C switch	Release 65xx , Release 66xx
MS4520V2-28S switch MS4520V2-24TP switch	Release 63xx
S6520X-HI switch series S6520X-EI switch series	Release 63xx , Release 65xx , Release 66xx
S6520X-SI switch series S6520-SI switch series	Release 63xx , Release 65xx , Release 66xx
S5000-EI switch series	Release 63xx , Release 65xx , Release 66xx
MS4600 switch series	Release 63xx , Release 65xx , Release 66xx
ES5500 switch series	Release 63xx , Release 65xx , Release 66xx
S5560S-EI switch series S5560S-SI switch series	Release 63xx
S5500V3-24P-SI switch S5500V3-48P-SI switch	Release 63xx
S5500V3-SI switch series (except S5500V3-24P-SI and S5500V3-48P-SI)	Release 11xx
S5170-EI switch series	Release 11xx
S5130S-HI switch series S5130S-EI switch series S5130S-SI switch series S5130S-LI switch series	Release 63xx
S5120V2-SI switch series S5120V2-LI switch series	Release 63xx
S5120V3-EI switch series	Release 11xx
S5120V3-36F-SI switch S5120V3-28P-HPWR-SI switch S5120V3-54P-PWR-SI switch	Release 11xx
S5120V3-SI switch series (except S5120V3-36F-SI, S5120V3-28P-HPWR-SI, and S5120V3-54P-PWR-SI)	Release 63xx
S5120V3-LI switch series	Release 63xx
S3600V3-EI switch series	Release 11xx
S3600V3-SI switch series	Release 11xx
S3100V3-EI switch series S3100V3-SI switch series	Release 63xx
S5110V2 switch series	Release 63xx
S5110V2-SI switch series	Release 63xx
S5000V3-EI switch series S5000V5-EI switch series	Release 63xx
S5000E-X switch S5000X-EI switch series	Release 63xx
E128C switch E152C switch E500C switch series E500D switch series	Release 63xx
MS4320V2 switch series MS4320V3 switch series MS4300V2 switch series MS4320 switch series MS4200 switch series	Release 63xx
WS5850-WiNet switch series	Release 63xx
WS5820-WiNet switch series WS5810-WiNet switch series	Release 63xx
WAS6000 switch series	Release 63xx
IE4300-12P-AC switch IE4300-12P-PWR switch IE4300-M switch series IE4320 switch series	Release 63xx

Restrictions and guidelines

When you configure S-MLAG, follow these restrictions and guidelines:

· When you assign a port to an aggregation group, the recommended configuration procedure is as follows:

a. Use the display this command in interface view to check the following attribute configurations of the port:

- Port isolation.

- QinQ.

- VLAN.

- VLAN mapping.

b. If any of the above configurations exist, use the undo forms of the corresponding commands to remove these configurations. This enables the port to use the default attribute configurations.

c. Assign the port to the aggregation group.

· Make sure the S-MLAG member devices have consistent link aggregation configuration.

· To ensure correct service traffic forwarding, configure the same service settings on the S-MLAG member devices.

Procedures

Configuring Device A

# Set the LACP system MAC address to 0001-0001-0001.

<DeviceA> system-view

[DeviceA] lacp system-mac 1-1-1

# Set the LACP system priority to 123.

[DeviceA] lacp system-priority 123

# Set the LACP system number to 1.

[DeviceA] lacp system-number 1

# Create Layer 2 aggregate interface Bridge-Aggregation 1, and set the link aggregation mode to dynamic.

[DeviceA] interface bridge-aggregation 1

[DeviceA-Bridge-Aggregation1] link-aggregation mode dynamic

# Configure Bridge-Aggregation 1 as an edge aggregate interface.

[DeviceA-Bridge-Aggregation1] lacp edge-port

# Assign Bridge-Aggregation 1 to S-MLAG group 100.

[DeviceA-Bridge-Aggregation1] port s-mlag group 100

[DeviceA-Bridge-Aggregation1] quit

# Assign GigabitEthernet 1/0/1 to aggregation group 1.

[DeviceA] interface gigabitethernet 1/0/1

[DeviceA-GigabitEthernet1/0/1] port link-aggregation group 1

[DeviceA-GigabitEthernet1/0/1] quit

Configuring Device B

# Set the LACP system MAC address to 0001-0001-0001.

<DeviceB> system-view

[DeviceB] lacp system-mac 1-1-1

# Set the LACP system priority to 123.

[DeviceB] lacp system-priority 123

# Set the LACP system number to 2.

[DeviceB] lacp system-number 2

# Create Layer 2 aggregate interface Bridge-Aggregation 2, and set the link aggregation mode to dynamic.

[DeviceB] interface bridge-aggregation 2

[DeviceC-Bridge-Aggregation2] link-aggregation mode dynamic

# Configure Bridge-Aggregation 2 as an edge aggregate interface.

[DeviceB-Bridge-Aggregation2] lacp edge-port

# Assign Bridge-Aggregation 2 to S-MLAG group 100.

[DeviceB-Bridge-Aggregation2] port s-mlag group 100

# Assign GigabitEthernet 1/0/1 to aggregation group 2.

[DeviceB] interface gigabitethernet 1/0/1

[DeviceB-GigabitEthernet1/0/1] port link-aggregation group 2

[DeviceB-GigabitEthernet1/0/1] quit

Configuring Device C

# Set the LACP system MAC address to 0001-0001-0001.

<DeviceC> system-view

[DeviceC] lacp system-mac 1-1-1

# Set the LACP system priority to 123.

[DeviceC] lacp system-priority 123

# Set the LACP system number to 3.

[DeviceC] lacp system-number 3

# Create Layer 2 aggregate interface Bridge-Aggregation 3, and set the link aggregation mode to dynamic.

[DeviceC] interface bridge-aggregation 3

[DeviceC-Bridge-Aggregation3] link-aggregation mode dynamic

# Configure Bridge-Aggregation 3 as an edge aggregate interface.

[DeviceC-Bridge-Aggregation3] lacp edge-port

# Assign Bridge-Aggregation 3 to S-MLAG group 100.

[DeviceC-Bridge-Aggregation3] port s-mlag group 100

# Assign GigabitEthernet 1/0/1 to aggregation group 3.

[DeviceC] interface gigabitethernet 1/0/1

[DeviceC-GigabitEthernet1/0/1] port link-aggregation group 3

[DeviceC-GigabitEthernet1/0/1] quit

Verifying the configuration

# Before you configure dynamic link aggregation on the server, verify that the aggregation member ports are in individual state on Device A, Device B, and Device C to forward traffic independently.

[DeviceA] display link-aggregation verbose

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port, M -- Management port, R -- Reference port

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

Aggregate Interface: Bridge-Aggregation1

Creation Mode: Manual

Aggregation Mode: Dynamic

Loadsharing Type: Shar

Management VLANs: None

System ID: 0x7b, 0001-0001-0001

Local:

Port Status Priority Index Oper-Key Flag

GE1/0/1 I 32768 16385 50100 {AG}

Remote:

Actor Priority Index Oper-Key SystemID Flag

GE1/0/1 32768 0 0 0x8000, 0000-0000-0000 {DEF}

[DeviceB] display link-aggregation verbose

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port, M -- Management port, R -- Reference port

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

Aggregate Interface: Bridge-Aggregation2

Creation Mode: Manual

Aggregation Mode: Dynamic

Loadsharing Type: Shar

Management VLANs: None

System ID: 0x7b, 0001-0001-0001

Local:

Port Status Priority Index Oper-Key Flag

GE1/0/1 I 32768 32769 50100 {AG}

Remote:

Actor Priority Index Oper-Key SystemID Flag

GE1/0/1 32768 0 0 0x8000, 0000-0000-0000 {DEF}

[DeviceC] display link-aggregation verbose

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port, M -- Management port, R -- Reference port

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

Aggregate Interface: Bridge-Aggregation3

Creation Mode: Manual

Aggregation Mode: Dynamic

Loadsharing Type: Shar

Management VLANs: None

System ID: 0x7b, 0001-0001-0001

Local:

Port Status Priority Index Oper-Key Flag

GE1/0/1 I 32768 49153 50100 {AG}

Remote:

Actor Priority Index Oper-Key SystemID Flag

GE1/0/1 32768 0 0 0x8000, 0000-0000-0000 {DEF}

# After you configure dynamic link aggregation on the server, verify that the aggregation member ports are selected on Device A, Device B, and Device C, which indicates that the multichassis link aggregation has been set up.

[DeviceA] display link-aggregation verbose

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port, M -- Management port, R -- Reference port

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

Aggregate Interface: Bridge-Aggregation1

Creation Mode: Manual

Aggregation Mode: Dynamic

Loadsharing Type: Shar

Management VLANs: None

System ID: 0x7b, 0001-0001-0001

Local:

Port Status Priority Index Oper-Key Flag

GE1/0/1(R) S 32768 16385 50100 {ACDEF}

Remote:

Actor Priority Index Oper-Key SystemID Flag

GE1/0/1 32768 1 1 0x8000, 5022-e533-0400 {ACDEF}

[DeviceB] display link-aggregation verbose

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port, M -- Management port, R -- Reference port

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

Aggregate Interface: Bridge-Aggregation2

Creation Mode: Manual

Aggregation Mode: Dynamic

Loadsharing Type: Shar

Management VLANs: None

System ID: 0x7b, 0001-0001-0001

Local:

Port Status Priority Index Oper-Key Flag

GE1/0/1(R) S 32768 32769 50100 {ACDEF}

Remote:

Actor Priority Index Oper-Key SystemID Flag

GE1/0/1 32768 2 1 0x8000, 5022-e533-0400 {ACDEF}

[DeviceC] display link-aggregation verbose

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port, M -- Management port, R -- Reference port

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

Aggregate Interface: Bridge-Aggregation3

Creation Mode: Manual

Aggregation Mode: Dynamic

Loadsharing Type: Shar

Management VLANs: None

System ID: 0x7b, 0001-0001-0001

Local:

Port Status Priority Index Oper-Key Flag

GE1/0/1(R) S 32768 49153 50100 {ACDEF}

Remote:

Actor Priority Index Oper-Key SystemID Flag

GE1/0/1 32768 3 1 0x8000, 5022-e533-0400 {ACDEF}

Configuration files

IMPORTANT:

Support for the port link-mode bridge command depends on the device model.

· Device A:

lacp system-mac 0001-0001-0001

lacp system-number 1

lacp system-priority 123

interface Bridge-Aggregation1

link-aggregation mode dynamic

lacp edge-port

port s-mlag group 100

interface GigabitEthernet1/0/1

port link-mode bridge

port link-aggregation group 1

· Device B:

lacp system-mac 0001-0001-0001

lacp system-number 2

lacp system-priority 123

interface Bridge-Aggregation2

link-aggregation mode dynamic

lacp edge-port

port s-mlag group 100

interface GigabitEthernet1/0/1

port link-mode bridge

port link-aggregation group 2

· Device C:

lacp system-mac 0001-0001-0001

lacp system-number 3

lacp system-priority 123

interface Bridge-Aggregation3

link-aggregation mode dynamic

lacp edge-port

port s-mlag group 100

interface GigabitEthernet1/0/1

port link-mode bridge

port link-aggregation group 3

H3C Fixed Port Campus Switches Configuration Examples-6W103

Network configuration

Analysis

Restrictions and guidelines

Cloud & AI

InterConnect

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Resources

Partner Business Management

Company Information

News & Events

Contact Us