The configuration examples in this document were created and verified in a lab environment, and all the switches were started with the factory default configuration. When you are working on a live network, make sure you understand the potential impact of every command on your network.

This document assumes that you have basic knowledge of IGMP snooping.

Example: Configuring multicast group policies

Network configuration

As shown in Figure 1:

· Router A runs IGMP and acts as the IGMP querier.

· Switch A runs IGMP snooping.

Configure multicast group policies on Switch A to meet the following requirements:

· Host A receives only the multicast data addressed to multicast group 224.1.1.1.

· Host B and Host C receive only the multicast data addressed to multicast group 225.1.1.1.

Figure 1 Network diagram

Analysis

To meet the network requirements, you must perform the following tasks:

· IGMPv2 snooping cannot process IGMPv3 messages. It floods IGMPv3 messages in the VLAN to which the IGMPv3 messages belong. To avoid this problem, specify IGMP snooping version 3 for VLAN 100.

· To avoid receiver hosts in VLAN 100 from receiving multicast data addressed to other groups, enable dropping unknown multicast data in VLAN 100.

· To configure multicast group policies, specify a basic ACL and create ACL rules to define the groups that you want the receiver hosts to join.

Applicable hardware and software versions

The following matrix shows the hardware and software versions to which this configuration example is applicable:

Hardware	Software version
S6812 switch series S6813 switch series	Release 66xx
S6550XE-HI switch series	Release 6008 and later
S6525XE-HI switch series	Release 6008 and later
S5850 switch series	Release 8005 and later
S5570S-EI switch series	Release 11xx
S5560X-EI switch series	Release 63xx, Release 65xx, Release 66xx
S5560X-HI switch series	Release 63xx, Release 65xx, Release 66xx
S5500V2-EI switch series	Release 63xx, Release 65xx, Release 66xx
MS4520V2-30F switch	Release 63xx, Release 65xx, Release 66xx
MS4520V2-30C switch MS4520V2-54C switch	Release 65xx, Release 66xx
MS4520V2-28S switch MS4520V2-24TP switch	Release 63xx
S6520X-HI switch series S6520X-EI switch series	Release 63xx, Release 65xx, Release 66xx
S6520X-SI switch series S6520-SI switch series	Release 63xx, Release 65xx, Release 66xx
S5000-EI switch series	Release 63xx, Release 65xx, Release 66xx
MS4600 switch series	Release 63xx, Release 65xx, Release 66xx
ES5500 switch series	Release 63xx, Release 65xx, Release 66xx
S5560S-EI switch series S5560S-SI switch series	Release 63xx
S5500V3-24P-SI S5500V3-48P-SI	Release 63xx
S5500V3-SI switch series (except S5500V3-24P-SI and S5500V3-48P-SI)	Release 11xx
S5170-EI switch series	Release 11xx
S5130S-HI switch series S5130S-EI switch series S5130S-SI switch series S5130S-LI switch series	Release 63xx
S5120V2-SI switch series S5120V2-LI switch series	Release 63xx
S5120V3-EI switch series	Release 11xx
S5120V3-36F-SI S5120V3-28P-HPWR-SI S5120V3-54P-PWR-SI	Release 11xx
S5120V3-SI switch series (except S5120V3-36F-SI, S5120V3-28P-HPWR-SI, and S5120V3-54P-PWR-SI)	Release 63xx
S5120V3-LI switch series	Release 63xx
S3600V3-EI switch series	Release 11xx
S3600V3-SI switch series	Release 11xx
S3100V3-EI switch series S3100V3-SI switch series	Release 63xx
S5110V2 switch series	Release 63xx
S5110V2-SI switch series	Release 63xx
S5000V3-EI switch series S5000V5-EI switch series	Release 63xx
S5000E-X switch series S5000X-EI switch series	Release 63xx
E128C switch E152C switch E500C switch series E500D switch series	Release 63xx
MS4320V2 switch series MS4320V3 switch series MS4300V2 switch series MS4320 switch series MS4200 switch series	Release 63xx
WS5850-WiNet switch series	Release 63xx
WS5820-WiNet switch series WS5810-WiNet switch series	Release 63xx
WAS6000 switch series	Release 63xx
IE4300-12P-AC switch IE4300-12P-PWR switch IE4300-M switch series IE4320 switch series	Release 63xx

Restrictions and guidelines

When you configure multicast group polices, follow these restrictions and guidelines:

· You must globally enable IGMP snooping in system view before you enable IGMP snooping for a VLAN in VLAN view.

· You can configure multicast group policies for all ports in IGMP-snooping view or for the current port in interface view. The configuration made in interface view takes priority over the configuration made in IGMP-snooping view.

Procedures

1. Assign an IP address and subnet mask to each interface on the routers in the PIM-DM domain. (Details not shown.)

2. Configure a unicast routing protocol on the routers in the PIM-DM domain. (Details not shown.)

3. Enable multicast routing globally on the routers in the PIM-DM domain. (Details not shown.)

4. Enable PIM-DM for the interfaces through which routers connects with each other on the routers in the PIM-DM domain. (Details not shown.)

5. Configure Router A:

# Enable IP multicast routing globally.

<RouterA> system-view

[RouterA] multicast routing

[RouterA-mrib] quit

# Enable IGMPv3 on GigabitEthernet 1/0/1.

[RouterA] interface gigabitethernet 1/0/1

[RouterA-GigabitEthernet1/0/1] igmp enable

[RouterA-GigabitEthernet1/0/1] igmp version 3

[RouterA-GigabitEthernet1/0/1] quit

6. Configure Switch A:

# Enable IGMP snooping globally.

<SwitchA> system-view

[SwitchA] igmp-snooping

[SwitchA-igmp-snooping] quit

# Create VLAN 100, and assign GigabitEthernet 1/0/1 through GigabitEthernet 1/0/4 to VLAN 100.

[SwitchA] vlan 100

[SwitchA-vlan100] port gigabitethernet 1/0/1 to gigabitethernet 1/0/4

# Enable IGMPv3 snooping and enable dropping unknown multicast data for VLAN 100.

[SwitchA-vlan100] igmp-snooping enable

[SwitchA-vlan100] igmp-snooping version 3

[SwitchA-vlan100] igmp-snooping drop-unknown

[SwitchA-vlan100] quit

# Configure a multicast group policy for VLAN 100 on GigabitEthernet 1/0/2 so that Host A can join only multicast group 224.1.1.1.

[SwitchA] acl basic 2000

[SwitchA-acl-ipv4-basic-2000] rule permit source 224.1.1.1 0

[SwitchA-acl-ipv4-basic-2000] quit

[SwitchA] interface gigabitethernet 1/0/2

[SwitchA-GigabitEthernet1/0/2] igmp-snooping group-policy 2000 vlan 100

[SwitchA-GigabitEthernet1/0/2] quit

# Configure a multicast group policy globally for VLAN 100 so that Host B and Host C can join only multicast group 225.1.1.1.

[SwitchA] acl basic 2001

[SwitchA-acl-ipv4-basic-2001] rule permit source 225.1.1.1 0

[SwitchA-acl-ipv4-basic-2001] quit

[SwitchA] igmp-snooping

[SwitchA-igmp-snooping] group-policy 2001 vlan 100

[SwitchA-igmp-snooping] quit

Verifying the configuration

# Send IGMP reports from Host A, Host B, and Host C to join multicast groups 224.1.1.1, 224.2.2.2, and 225.1.1.1. (Details not shown.)

# Send multicast data from the source to the multicast groups. (Details not shown.)

# Display dynamic IGMP snooping group entries for VLAN 100 on Switch A.

[SwitchA] display igmp-snooping group vlan 100

Total 2 entries.

VLAN 100: Total 2 entries.

(0.0.0.0, 224.1.1.1)

Host ports (1 in total):

GE1/0/2 (00:03:09)

(0.0.0.0, 225.1.1.1)

Host ports (2 in total):

GE1/0/3 (00:04:04)

GE1/0/4 (00:02:38)

The output shows the following information:

· Host A has joined multicast group 224.1.1.1 through GigabitEthernet 1/0/2, and it has not joined multicast groups 224.2.2.2 and 225.1.1.1.

· Host B and Host C have joined multicast group 225.1.1.1 through GigabitEthernet 1/0/3 and GigabitEthernet 1/0/4, respectively. They have not joined multicast groups 224.1.1.1 and 224.2.2.2.

· Multicast group policies have taken effect.

Configuration files

IMPORTANT:

Support for the port link-mode bridge command depends on the device model.

· Router A:

interface GigabitEthernet1/0/1

port link-mode route

ip address 10.1.1.1 255.255.255.0

igmp enable

igmp version 3

multicast routing

· Switch A:

igmp-snooping

group-policy 2001 vlan 100

vlan 100

igmp-snooping enable

igmp-snooping drop-unknown

igmp-snooping version 3

interface GigabitEthernet1/0/1

port link-mode bridge

port access vlan 100

interface GigabitEthernet1/0/2

port link-mode bridge

port access vlan 100

igmp-snooping group-policy 2000 vlan 100

interface GigabitEthernet1/0/3

port link-mode bridge

port access vlan 100

interface GigabitEthernet1/0/4

port link-mode bridge

port access vlan 100

acl basic 2000

rule 0 permit source 224.1.1.1 0

acl basic 2001

rule 0 permit source 225.1.1.1 0

Example: Configuring IGMP snooping static ports

Network configuration

As shown in Figure 2:

· All switches in VLAN 100 run IGMP snooping.

· Router A runs IGMPv2 and acts as the IGMP querier.

· STP runs in VLAN 100. The direct route between Switch A and Switch B or the route from Switch A to Switch B with Switch C as the intermediate device is blocked to avoid loops.

Configure IGMP snooping static ports to meet the following requirements:

· Multicast data uninterruptedly flows to the receiver hosts after a link switchover occurs between Switch A and Switch B.

· Host A, Host B, and Host C permanently receive the multicast data addressed to multicast group 224.1.1.1.

Figure 2 Network diagram

Analysis

To meet the network requirements, you must perform the following tasks:

· By default, when a link switchover occurs, multicast data can flow along the new link after a minimum of one IGMP query-response cycle. Multicast delivery is interrupted during this process.

Configure GigabitEthernet 1/0/2 and GigabitEthernet 1/0/3 on Switch A, GigabitEthernet 1/0/4 on Switch B, and GigabitEthernet 1/0/2 on Switch C as static router ports. Then, multicast data will be forwarded to these ports.

· Configure GigabitEthernet 1/0/2 and GigabitEthernet 1/0/3 on Switch B, and GigabitEthernet 1/0/3 on Switch C as static member ports of multicast group 224.1.1.1. Then, multicast data for the group will always be forwarded out of these ports, and Host A, Host B, and Host C can always receive the data.

Applicable hardware and software versions

The following matrix shows the hardware and software versions to which this configuration example is applicable:

Hardware	Software version
S6812 switch series S6813 switch series	Release 66xx
S6550XE-HI switch series	Release 6008 and later
S6525XE-HI switch series	Release 6008 and later
S5850 switch series	Release 8005 and later
S5570S-EI switch series	Release 11xx
S5560X-EI switch series	Release 63xx, Release 65xx, Release 66xx
S5560X-HI switch series	Release 63xx, Release 65xx, Release 66xx
S5500V2-EI switch series	Release 63xx, Release 65xx, Release 66xx
MS4520V2-30F switch	Release 63xx, Release 65xx, Release 66xx
MS4520V2-30C switch MS4520V2-54C switch	Release 65xx, Release 66xx
MS4520V2-28S switch MS4520V2-24TP switch	Release 63xx
S6520X-HI switch series S6520X-EI switch series	Release 63xx, Release 65xx, Release 66xx
S6520X-SI switch series S6520-SI switch series	Release 63xx, Release 65xx, Release 66xx
S5000-EI switch series	Release 63xx, Release 65xx, Release 66xx
MS4600 switch series	Release 63xx, Release 65xx, Release 66xx
ES5500 switch series	Release 63xx, Release 65xx, Release 66xx
S5560S-EI switch series S5560S-SI switch series	Release 63xx
S5500V3-24P-SI S5500V3-48P-SI	Release 63xx
S5500V3-SI switch series (except S5500V3-24P-SI and S5500V3-48P-SI)	Release 11xx
S5170-EI switch series	Release 11xx
S5130S-HI switch series S5130S-EI switch series S5130S-SI switch series S5130S-LI switch series	Release 63xx
S5120V2-SI switch series S5120V2-LI switch series	Release 63xx
S5120V3-EI switch series	Release 11xx
S5120V3-36F-SI S5120V3-28P-HPWR-SI S5120V3-54P-PWR-SI	Release 11xx
S5120V3-SI switch series (except S5120V3-36F-SI, S5120V3-28P-HPWR-SI, and S5120V3-54P-PWR-SI)	Release 63xx
S5120V3-LI switch series	Release 63xx
S3600V3-EI switch series	Release 11xx
S3600V3-SI switch series	Release 11xx
S3100V3-EI switch series S3100V3-SI switch series	Release 63xx
S5110V2 switch series	Release 63xx
S5110V2-SI switch series	Release 63xx
S5000V3-EI switch series S5000V5-EI switch series	Release 63xx
S5000E-X switch series S5000X-EI switch series	Release 63xx
E128C switch E152C switch E500C switch series E500D switch series	Release 63xx
MS4320V2 switch series MS4320V3 switch series MS4300V2 switch series MS4320 switch series MS4200 switch series	Release 63xx
WS5850-WiNet switch series	Release 63xx
WS5820-WiNet switch series WS5810-WiNet switch series	Release 63xx
WAS6000 switch series	Release 63xx
IE4300-12P-AC switch IE4300-12P-PWR switch IE4300-M switch series IE4320 switch series	Release 63xx

Restrictions and guidelines

When you configure IGMP snooping static ports, you must globally enable IGMP snooping in system view before you enable IGMP snooping for a VLAN in VLAN view.

Procedures

1. Assign an IP address and subnet mask to each interface on the routers in the PIM-DM domain. (Details not shown.)

2. Configure OSPF on the routers in the PIM-DM domain. (Details not shown.)

3. Enable multicast routing globally on the routers in the PIM-DM domain. (Details not shown.)

4. Enable PIM-DM for the interfaces through which routers connects with each other in the PIM-DM domain. (Details not shown.)

5. Configure Router A:

# Enable IP multicast routing.

<RouterA> system-view

[RouterA] multicast routing

[RouterA-mrib] quit

# Enable IGMP on GigabitEthernet 1/0/1.

[RouterA] interface gigabitethernet 1/0/1

[RouterA-GigabitEthernet1/0/1] igmp enable

[RouterA-GigabitEthernet1/0/1] quit

6. Configure Switch A:

# Enable IGMP snooping globally.

<SwitchA> system-view

[SwitchA] igmp-snooping

[SwitchA-igmp-snooping] quit

# Create VLAN 100, assign GigabitEthernet 1/0/1 through GigabitEthernet 1/0/4 to this VLAN, and enable IGMP snooping for this VLAN.

[SwitchA] vlan 100

[SwitchA-vlan100] port gigabitethernet 1/0/1 to gigabitethernet 1/0/4

[SwitchA-vlan100] igmp-snooping enable

[SwitchA-vlan100] quit

# Configure GigabitEthernet 1/0/2 and GigabitEthernet 1/0/3 as static router ports.

[SwitchA] interface gigabitethernet 1/0/2

[SwitchA-GigabitEthernet1/0/2] igmp-snooping static-router-port vlan 100

[SwitchA-GigabitEthernet1/0/2] quit

[SwitchA] interface gigabitethernet 1/0/3

[SwitchA-GigabitEthernet1/0/3] igmp-snooping static-router-port vlan 100

[SwitchA-GigabitEthernet1/0/3] quit

7. Configure Switch B:

# Enable IGMP snooping globally.

<SwitchB> system-view

[SwitchB] igmp-snooping

[SwitchB-igmp-snooping] quit

# Create VLAN 100, assign GigabitEthernet 1/0/1 and GigabitEthernet 1/0/4 to this VLAN, and enable IGMP snooping for this VLAN.

[SwitchB] vlan 100

[SwitchB-vlan100] port gigabitethernet 1/0/1 gigabitethernet 1/0/4

[SwitchB-vlan100] igmp-snooping enable

[SwitchB-vlan100] quit

# Configure GigabitEthernet 1/0/4 as a static router port.

[SwitchB] interface gigabitethernet 1/0/4

[SwitchB-GigabitEthernet1/0/4] igmp-snooping static-router-port vlan 100

[SwitchB-GigabitEthernet1/0/4] quit

# Configure GigabitEthernet 1/0/2 and GigabitEthernet 1/0/3 as static member ports for multicast group 224.1.1.1 in VLAN 100.

[SwitchB] interface gigabitethernet 1/0/2

[SwitchB-GigabitEthernet1/0/2] igmp-snooping static-group 224.1.1.1 vlan 100

[SwitchB-GigabitEthernet1/0/2] quit

[SwitchB] interface gigabitethernet 1/0/3

[SwitchB-GigabitEthernet1/0/3] igmp-snooping static-group 224.1.1.1 vlan 100

[SwitchB-GigabitEthernet1/0/3] quit

8. Configure Switch C:

# Enable IGMP snooping globally.

<SwitchC> system-view

[SwitchC] igmp-snooping

[SwitchC-igmp-snooping] quit

# Create VLAN 100, assign GigabitEthernet 1/0/1 through GigabitEthernet 1/0/4 to this VLAN, and enable IGMP snooping for this VLAN.

[SwitchC] vlan 100

[SwitchC-vlan100] port gigabitethernet 1/0/1 to gigabitethernet 1/0/4

[SwitchC-vlan100] igmp-snooping enable

[SwitchC-vlan100] quit

# Configure GigabitEthernet 1/0/2 as a static router port in VLAN 100.

[SwitchC] interface gigabitethernet 1/0/2

[SwitchC-GigabitEthernet1/0/2] igmp-snooping static-router-port vlan 100

[SwitchC-GigabitEthernet1/0/2] quit

# Configure GigabitEthernet 1/0/3 as a static member port of multicast group 224.1.1.1 in VLAN 100.

[SwitchC] interface gigabitethernet 1/0/3

[SwitchC-GigabitEthernet1/0/3] igmp-snooping static-group 224.1.1.1 vlan 100

[SwitchC-GigabitEthernet1/0/3] quit

Verifying the configuration

Verify the configuration before hosts join any multicast groups.

# Display static router port information for VLAN 100 on Switch A.

[SwitchA] display igmp-snooping static-router-port vlan 100

VLAN 100:

Router ports (2 in total):

GE1/0/2

GE1/0/3

The output shows that GigabitEthernet 1/0/2 and GigabitEthernet 1/0/3 on Switch A have become static router ports in VLAN 100.

# Display static router port information for VLAN 100 on Switch B.

[SwitchB] display igmp-snooping static-router-port vlan 100

VLAN 100:

Router ports (1 in total):

GE1/0/4

The output shows that GigabitEthernet 1/0/4 on Switch B has become a static router port in VLAN 100.

# Display static IGMP snooping group entries for VLAN 100 on Switch B.

[SwitchB] display igmp-snooping static-group vlan 100

Total 1 entries.

VLAN 100: Total 1 entries.

(0.0.0.0, 224.1.1.1)

Host ports (2 in total):

GE1/0/2

GE1/0/3

The output shows that GigabitEthernet 1/0/2 and GigabitEthernet 1/0/3 on Switch B have become static member ports of multicast group 224.1.1.1 in VLAN 100.

# Display static router port information for VLAN 100 on Switch C.

[SwitchC] display igmp-snooping static-router-port vlan 100

VLAN 100:

Router ports (1 in total):

GE1/0/2

The output shows that GigabitEthernet 1/0/2 on Switch C has become a static router port in VLAN 100.

# Display static IGMP snooping group entries for VLAN 100 on Switch C.

[SwitchC] display igmp-snooping static-group vlan 100

Total 1 entries.

VLAN 100: Total 1 entries.

(0.0.0.0, 224.1.1.1)

Host ports (1 in total):

GE1/0/3

The output shows that GigabitEthernet 1/0/3 on Switch C has become a static group member of multicast group 224.1.1.1.

Configuration files

IMPORTANT:

Support for the port link-mode bridge command depends on the device model.

· Router A:

interface GigabitEthernet1/0/1

port link-mode route

ip address 10.1.1.1 255.255.255.0

igmp enable

multicast routing

· Switch A:

igmp-snooping

vlan 100

igmp-snooping enable

interface GigabitEthernet1/0/1

port link-mode bridge

port access vlan 100

interface GigabitEthernet1/0/2

port link-mode bridge

port access vlan 100

igmp-snooping static-router-port vlan 100

interface GigabitEthernet1/0/3

port link-mode bridge

port access vlan 100

igmp-snooping static-router-port vlan 100

· Switch B:

igmp-snooping

vlan 100

igmp-snooping enable

interface GigabitEthernet1/0/1

port link-mode bridge

port access vlan 100

interface GigabitEthernet1/0/2

port link-mode bridge

port access vlan 100

igmp-snooping static-group 224.1.1.1 vlan 100

interface GigabitEthernet1/0/3

port link-mode bridge

port access vlan 100

igmp-snooping static-group 224.1.1.1 vlan 100

interface GigabitEthernet1/0/4

port link-mode bridge

port access vlan 100

igmp-snooping static-router-port vlan 100

· Switch C:

igmp-snooping

vlan 100

igmp-snooping enable

interface GigabitEthernet1/0/1

port link-mode bridge

port access vlan 100

interface GigabitEthernet1/0/2

port link-mode bridge

port access vlan 100

igmp-snooping static-router-port vlan 100

interface GigabitEthernet1/0/3

port link-mode bridge

port access vlan 100

igmp-snooping static-group 224.1.1.1 vlan 100

interface GigabitEthernet1/0/4

port link-mode bridge

port access vlan 100

H3C Fixed Port Campus Switches Configuration Examples-6W103

Introduction

Prerequisites

Example: Configuring multicast group policies

Network configuration

Analysis

Applicable hardware and software versions

Restrictions and guidelines

Procedures

Verifying the configuration

Configuration files

Example: Configuring IGMP snooping static ports

Network configuration

Analysis

Applicable hardware and software versions

Restrictions and guidelines

Procedures

Verifying the configuration

Configuration files

Cloud & AI

InterConnect

Intelligent Computing

Security

SMB Products

Intelligent Terminal Products

Industry Solutions

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Training & Certification

Become a Partner

Partner Resources

Partner Business Management

Company Information

News & Events

Online Exhibition Center

Contact Us