• 产品与解决方案
  • 行业解决方案
  • 服务
  • 支持
  • 合作伙伴
  • 新华三人才研学中心
  • 关于我们

04-典型配置案例(AC+FIT AP)

目录

005-H3C无线控制器IPv6二层注册典型配置举例

本章节下载 005-H3C无线控制器IPv6二层注册典型配置举例  (231.39 KB)

005-H3C无线控制器IPv6二层注册典型配置举例

H3C无线控制器IPv6二层注册典型配置举例

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Copyright © 2023 新华三技术有限公司 版权所有,保留一切权利。

非经本公司书面许可,任何单位和个人不得擅自摘抄、复制本文档内容的部分或全部,并不得以任何形式传播。

除新华三技术有限公司的商标外,本手册中出现的其它公司的商标、产品标识及商品名称,由各自权利人拥有。

本文档中的信息可能变动,恕不另行通知。



1  简介

本文档介绍AP与AC间通过二层网络完成注册的配置举例。

2  配置前提

本文档适用于使用Comware软件版本的无线控制器和接入点产品,不严格与具体硬件版本对应,如果使用过程中与产品实际情况有差异,请参考相关产品手册,或以设备实际情况为准。

本文档中的配置均是在实验室环境下进行的配置和验证,配置前设备的所有参数均采用出厂时的缺省配置。如果您已经对设备进行了配置,为了保证配置效果,请确认现有配置和以下举例中的配置不冲突。

本文档假设您已了解IPv6基础与WLAN接入相关特性。

3  IPv6二层网络注册配置举例

3.1  组网需求

图1所示,集中式转发架构下,无线客户端Client、有线客户端Host通过L2 switch和AC相连,L2 switch通过PoE方式给AP供电,AC做为DHCPv6 server为AP、Client和Host分配IPv6地址。需要实现无线客户端Client通过AP连接到AC上,并能与有线客户端Host互相访问。

图1 Fit AP通过二层网络注册到AC配置举例组网图

 

3.2  配置思路

·     在AC上配置DHCPv6服务,使AP、无线客户端Client和有线客户端Host都能通过DHCPv6 server自动获取IPv6地址。

·     在L2 switch上开启PoE功能,为AP设备供电。

·     在AC上配置无线服务,确保Client可以通过配置的无线服务接入网络,并访问Host。

3.3  配置注意事项

·     配置AP的序列号时请确保该序列号与AP唯一对应。

·     配置L2 switch和AP相连的接口禁止VLAN 1报文通过,以防止VLAN 1内报文过多。

3.4  配置步骤

3.4.1  配置AC

(1)     配置AC接口

# 创建VLAN 100及其对应的VLAN接口,并为该接口配置IPv6地址。AP将通过该VLAN与AC建立CAPWAP隧道。

<AC> system-view

[AC] vlan 100

[AC-vlan100] quit

[AC] interface vlan-interface 100

[AC-Vlan-interface100] ipv6 address 1::1:0:0:1/96

[AC-Vlan-interface100] quit

# 创建VLAN 200及其对应的VLAN接口,并为该接口配置IPv6地址。Client使用该VLAN接入无线网络。

[AC] vlan 200

[AC-vlan200] quit

[AC] interface vlan-interface 200

[AC-Vlan-interface200] ipv6 address 1::2:0:0:1/96

[AC-Vlan-interface200] quit

# 创建VLAN 300及其对应的VLAN接口,并为该接口配置IPv6地址。Host使用该VLAN与AC建立连接。

[AC] vlan 300

[AC-vlan300] quit

[AC] interface vlan-interface 300

[AC-Vlan-interface300] ipv6 address 1::3:0:0:1/96

[AC-Vlan-interface300] quit

# 配置AC和L2 switch相连的接口GigabitEthernet1/0/1为Trunk类型,禁止VLAN 1报文通过,允许VLAN 100、VLAN 200和VLAN 300通过。

[AC] interface gigabitethernet 1/0/1

[AC-GigabitEthernet1/0/1] port link-type trunk

[AC-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[AC-GigabitEthernet1/0/1] port trunk permit vlan 100 200 300

[AC-GigabitEthernet1/0/1] quit

(2)     配置DHCPv6服务

# 配置接口Vlan-interface100、Vlan-interface200和Vlan-interface300工作在DHCPv6服务器模式,并配置接口引用DHCP地址池。

[AC] interface vlan-interface 100

[AC-Vlan-interface100] ipv6 dhcp select server

[AC-Vlan-interface100] ipv6 dhcp server apply pool 1

[AC-Vlan-interface100] interface vlan-interface 200

[AC-Vlan-interface200] ipv6 dhcp server apply pool 2

[AC-Vlan-interface200] ipv6 dhcp select server

[AC-Vlan-interface200] interface vlan-interface 300

[AC-Vlan-interface300] ipv6 dhcp server apply pool 3

[AC-Vlan-interface300] ipv6 dhcp select server

# 取消设备发布RA消息的抑制功能。配置被管理地址的配置标志位为1,即主机通过DHCPv6服务器获取IPv6地址。配置其他信息配置标志位为1,即主机通过DHCPv6服务器获取除IPv6地址以外的其他信息。

[AC-Vlan-interface300] interface vlan-interface 100

[AC-Vlan-interface100] undo ipv6 nd ra halt

[AC-Vlan-interface100] ipv6 nd autoconfig managed-address-flag

[AC-Vlan-interface100] ipv6 nd autoconfig other-flag

[AC-Vlan-interface100] interface vlan-interface 200

[AC-Vlan-interface200] undo ipv6 nd ra halt

[AC-Vlan-interface200] ipv6 nd autoconfig managed-address-flag

[AC-Vlan-interface200] ipv6 nd autoconfig other-flag

[AC-Vlan-interface200] interface vlan-interface 300

[AC-Vlan-interface300] undo ipv6 nd ra halt

[AC-Vlan-interface300] ipv6 nd autoconfig managed-address-flag

[AC-Vlan-interface300] ipv6 nd autoconfig other-flag

[AC-Vlan-interface300] quit

# 配置DHCPv6地址池1,为1::1:0:0:0/96网的AP分配IPv6地址等参数。

[AC] ipv6 dhcp pool 1

[AC-dhcp6-pool-1] network 1::1:0:0:0/96

[AC-dhcp6-pool-1] quit

# 配置DHCPv6地址池2,为1::2:0:0:0/96网段的Client分配IPv6地址等参数。

[AC] ipv6 dhcp pool 2

[AC-dhcp6-pool-2] network 1::2:0:0:0/96

[AC-dhcp6-pool-2] quit

# 配置DHCPv6地址池3,为1::3:0:0:0/96网段的Host分配IPv6地址等参数。

[AC] ipv6 dhcp pool 3

[AC-dhcp6-pool-3] network 1::3:0:0:0/96

[AC-dhcp6-pool-3] quit

(3)     配置无线服务

# 创建无线服务模板1,并进入无线服务模板视图。

[AC] wlan service-template 1

# 配置SSID为service。

[AC-wlan-st-1] ssid service

# 配置身份认证与密钥管理模式为PSK模式,配置PSK密钥为明文字符串12345678。

[AC-wlan-st-1] akm mode psk

[AC-wlan-st-1] preshared-key pass-phrase simple 12345678

# 配置加密套件为CCMP,安全信息元素为RSN。

[AC-wlan-st-1] cipher-suite ccmp

[AC-wlan-st-1] security-ie rsn

# 配置客户端数据报文转发位置为AC。(如果客户端数据报文的缺省转发位置与本配置相同,请跳过此步骤)

[AC-wlan-st-1] client forwarding-location ac

# 使能服务模板。

[AC-wlan-st-1] service-template enable

# 开启通过DHCPv6方式和ND方式学习客户端IPv6地址功能。

[AC-wlan-st-1] client ipv6-snooping dhcpv6-learning enable

[AC-wlan-st-1] client ipv6-snooping nd-learning enable

[AC-wlan-st-1] quit

(4)     配置AP

说明

在大规模组网时,推荐在AP组内进行配置。

 

# 创建手工AP,名称为officeap,型号名称为WA6320

[AC] wlan ap officeap model WA6320

# 设置AP的序列号为219801A28N819CE0002T。

[AC-wlan-ap-officeap] serial-id 219801A28N819CE0002T

[AC-wlan-ap-officeap] quit

# 创建AP组group1,并配置AP名称入组规则。

[AC] wlan ap-group group1

[AC-wlan-ap-group-group1] ap officeap

# 将无线服务模板1绑定到AP组group1下的Radio 1上,并指定客户端上线的VLANVLAN 200

[AC-wlan-ap-group-group1] ap-model WA6320

[AC-wlan-ap-group-group1-ap-model-WA6320] radio 1

[AC-wlan-ap-group-group1-ap-model-WA6320-radio-1] service-template 1 vlan 200

[AC-wlan-ap-group-group1-ap-model-WA6320-radio-1] radio enable

[AC-wlan-ap-group-group1-ap-model-WA6320-radio-1] quit

[AC-wlan-ap-group-group1-ap-model-WA6320] quit

[AC-wlan-ap-group-group1] quit

3.4.2  配置L2 switch

# 创建VLAN 100、VLAN 200和VLAN 300,其中VLAN 100用于转发AC和AP间CAPWAP隧道内的流量,VLAN 200为无线客户端接入的VLAN,VLAN 300为Host接入的VLAN。

<L2 switch> system-view

[L2 switch] vlan 100

[L2 switch-vlan100] quit

[L2 switch] vlan 200

[L2 switch-vlan200] quit

[L2 switch] vlan 300

[L2 switch-vlan300] quit

# 配置L2 switch和AC相连的接口GigabitEthernet1/0/1为Trunk类型,允许VLAN 100、VLAN 200和VLAN 300通过。

[L2 switch] interface gigabitEthernet 1/0/1

[L2 switch-GigabitEthernet1/0/1] port link-type trunk

[L2 switch-GigabitEthernet1/0/1] port trunk permit vlan 100 200 300

[L2 switch-GigabitEthernet1/0/1] quit

# 配置L2 switch和AP相连的接口GigabitEthernet1/0/2为Trunk类型,禁止VLAN 1报文通过,允许VLAN 100通过,当前Trunk口的PVID为100,并开启PoE远程供电功能。

[L2 switch] interfac gigabitEthernet 1/0/2

[L2 switch-GigabitEthernet1/0/2] port link-type trunk

[L2 switch-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[L2 switch-GigabitEthernet1/0/2] port trunk permit vlan 100

[L2 switch-GigabitEthernet1/0/2] port trunk pvid vlan 100

[L2 switch-GigabitEthernet1/0/2] poe enable

[L2 switch-GigabitEthernet1/0/2] quit

# 配置L2 switch和Host相连的接口GigabitEthernet1/0/3为Access类型,允许VLAN 300通过。

[L2 switch] interface gigabitEthernet 1/0/3

[L2 switch-GigabitEthernet1/0/3] port access vlan 300

[L2 switch-GigabitEthernet1/0/3] quit

3.5  验证配置

(1)     在AC上查看AP注册信息

# 在AC上使用命令display wlan ap all查看AP,可以看到AP的状态是R/M,表明AP已经成功注册到AC。

<AC> display wlan ap all

Total number of APs: 1

Total number of connected APs: 1

Total number of connected manual APs: 1

Total number of connected auto APs: 0

Total number of connected common APs: 1

Total number of connected WTUs: 0

Total number of inside APs: 0

Maximum supported APs: 3072

Remaining APs: 3071

Total AP licenses: 512

Local AP licenses: 512

Server AP licenses: 0

Remaining Local AP licenses: 511

Sync AP licenses: 0

 

                                 AP information

 State : I = Idle,      J  = Join,       JA = JoinAck,    IL = ImageLoad

         C = Config,    DC = DataCheck,  R  = Run,   M = Master,  B = Backup

 

AP name                APID    State   Model             Serial ID

officeap               1       R/M     WA6320            219801A28N819CE0002T

(2)     在AC上查看Client信息

# 在AC上使用命令display wlan client ipv6查看在线Client,可以看到Client已经连接到AP的radio1。

<AC> display wlan client ipv6

Total number of clients: 1

 

MAC address    AP name               IPv6 address                            VLAN

784f-43b6-077c officeap              1::2:0:0:3                              200

(3)     Host与Client可以相互ping通

# Client 通过DHCPv6 server获取到IPv6地址1::2:0:0:3,在Host上ping Client的IPv6地址可以ping通。同理,在Client上ping Host的IPv6地址也能ping通,不再赘述。

C:\Users\system32>ping 1::2:0:0:3 -t

 

Pinging 1::2:0:0:3 with 32 bytes of data:

Reply from 1::2:0:0:3: bytes=32 time=8ms TTL=255

Reply from 1::2:0:0:3: bytes=32 time<1ms TTL=255

Reply from 1::2:0:0:3: bytes=32 time<1ms TTL=255

Reply from 1::2:0:0:3: bytes=32 time<1ms TTL=255

Reply from 1::2:0:0:3: bytes=32 time<1ms TTL=255

Reply from 1::2:0:0:3: bytes=32 time<1ms TTL=255

Reply from 1::2:0:0:3: bytes=32 time<1ms TTL=255

Reply from 1::2:0:0:3: bytes=32 time<1ms TTL=255

Reply from 1::2:0:0:3: bytes=32 time<1ms TTL=255

Reply from 1::2:0:0:3: bytes=32 time<1ms TTL=255

Reply from 1::2:0:0:3: bytes=32 time<1ms TTL=255

 

Ping statistics for 1::2:0:0:3:

    Packets: Sent = 11, Received = 11, Lost = 0 (0% loss),

Approximate round trip times in milli-seconds:

    Minimum = 0ms, Maximum = 8ms, Average = 0ms

Control-C

^C

C:\Users\system32>

3.6  配置文件

·     AC

#

 dhcp enable

#

vlan 1

#

vlan 100

#

vlan 200

#

vlan 300

#

ipv6 dhcp pool 1

 network 1::1:0:0:0/96

#

ipv6 dhcp pool 2

 network 1::2:0:0:0/96

#

ipv6 dhcp pool 3

 network 1::3:0:0:0/96

#

wlan service-template 1

 ssid service

 client forwarding-location ac

 akm mode psk

 preshared-key pass-phrase cipher $c$3$9tIUHSkAUVqCH9/EPrL26ldkcEQnngexUEFj

 cipher-suite ccmp

 security-ie rsn

 client ipv6-snooping nd-learning enable

 client ipv6-snooping dhcpv6-learning enable

 service-template enable

#

interface Vlan-interface1

#

interface Vlan-interface100

 ipv6 dhcp select server

 ipv6 dhcp server apply pool 1

 ipv6 address 1::1:0:0:1/96

 ipv6 nd autoconfig managed-address-flag

 ipv6 nd autoconfig other-flag

 undo ipv6 nd ra halt

#

interface Vlan-interface200

 ipv6 dhcp select server

 ipv6 dhcp server apply pool 2

 ipv6 address 1::2:0:0:1/96

 ipv6 nd autoconfig managed-address-flag

 ipv6 nd autoconfig other-flag

 undo ipv6 nd ra halt

#

interface Vlan-interface300

 ipv6 dhcp select server

 ipv6 dhcp server apply pool 3

 ipv6 address 1::3:0:0:1/96

 ipv6 nd autoconfig managed-address-flag

 ipv6 nd autoconfig other-flag

 undo ipv6 nd ra halt

#

interface GigabitEthernet1/0/1

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100 200 300

 port trunk pvid vlan 100

#

wlan ap-group group1

 ap officeap

 ap-model WA6320

  radio 1

   radio enable

   service-template 1 vlan 200

  radio 2

#

wlan ap officeap model WA6320

 serial-id 219801A28N819CE0002T

#

·     L2 switch

#

vlan 100

#

vlan 200

#

vlan 300

#

interface GigabitEthernet1/0/1

 port link-type trunk

 port trunk permit vlan 1 100 200 300

port trunk pvid vlan 100

#

interface GigabitEthernet1/0/2

 port link-type trunk

 undo port trunk permit vlan 1

 port trunk permit vlan 100

 port trunk pvid vlan 100

 poe enable

#

interface GigabitEthernet1/0/3

 port access vlan 300

#

4  相关资料

·     《H3C无线控制器产品 配置指导》中的“网络互通配置指导”。

·     《H3C无线控制器产品 命令参考》中的“网络互通命令参考”。

·     《H3C无线控制器产品 配置指导》中的“AP管理配置指导”。

·     《H3C无线控制器产品 命令参考》中的“AP管理命令参考”。

 

不同款型规格的资料略有差异, 详细信息请向具体销售和400咨询。H3C保留在没有任何通知或提示的情况下对资料内容进行修改的权利!

新华三官网
联系我们