Public network IP over SRv6 uses SRv6 tunnels to carry public network IP services. This technology establishes SRv6 tunnels among geographically dispersed customer sites over an IPv6 network and transparently forwards Layer 3 customer traffic to remote sites over the IPv6 network through the tunnels.

Basic principle

Figure 1 shows a typical public network IP over SRv6 network. PE 1 and PE 2 use BGP to advertise public network IPv6 routes to each other over the IPv6 backbone network. The PEs use an SRv6 tunnel between them to forward public network traffic across sites.

Public network IP over SRv6 connects geographically dispersed sites that belong to the public network over the IPv6 backbone network.

Figure 1 Network diagram

‌

Route advertisement

Public network IPv4 over SRv6 and public network IPv6 over SRv6 use the same process to advertise routes. The following information uses public network IPv4 over SRv6 as an example to illustrate the process.

As shown in Figure 1, local routes of CE 1 are advertised to CE 2 by using the following process:

1. CE 1 uses static routing, RIP, OSPF, IS-IS, EBGP, or IBGP to advertise routes of the local site to PE 1.

2. After learning the route information of CE 1, PE 1 stores the routes of the local site to the routing table of the public network. At the same time, PE 1 converts the routes to BGP IPv4 unicast routes and adds an SID to each of the routes. Then, PE 1 advertises the BGP IPv4 unicast routes with the SID to PE 2.

¡ If next hop-based dynamic SID allocation is not enabled, all the public network routes are allocated the same End.DT4 or End.DT46 SID.

¡ If next hop-based dynamic SID allocation is enabled, public network routes with the same next hop are allocated the same End.DX4 SID.

3. When PE 2 receives the IPv4 unicast routes advertised by PE 1, it adds the routes to the routing table of the public network. PE 2 removes the End.DT4, End.DT46, or End.DX4 SID information from the routes, records the SID information, and then advertises the routes to CE 2.

4. By adding the received IPv4 unicast routes to the routing table, CE 2 learns the routes of CE 1.

Packet forwarding

Public network IP over SRv6 supports the following route recursion modes:

· SRv6 BE mode.

· SRv6 TE mode.

· SRv6 TE and SRv6 BE hybrid mode.

· SRv6 TE and SRv6 BE FRR mode.

The packet forwarding process differs by the route recursion mode in use.

SRv6 BE mode

This mode is also called SID-based forwarding mode. In this mode, a PE forwards an SRv6 packet by searching the IPv6 routing table based on the SRv6 SID encapsulated in the packet.

Public network IPv4 over SRv6 and public network IPv6 over SRv6 use the same process to forward packets. The following information uses public network IPv4 over SRv6 as an example to illustrate the process.

As shown in Figure 1, CE 2 forwards an IPv4 packet to CE 1 as follows:

1. CE 2 sends the IPv4 packet to PE 2.

2. After PE 2 receives the packet, it searches for a route that matches the destination IPv4 address of the packet in the routing table of the public network. The corresponding End.DT4, End.DT46, or End.DX4 SID is found. Then, PE 2 encapsulates an outer IPv6 header for the packet. The End.DT4, End.DT46, or End.DX4 SID is encapsulated in the outer IPv6 header as the destination address.

3. PE 2 searches the IPv6 routing table based on the End.DT4, End.DT46, or End.DX4 SID for the optimal IGP route and forwards the packet to P through the route.

4. P searches the IPv6 routing table based on the End.DT4, End.DT46, or End.DX4 SID for the optimal IGP route and forwards the packet to PE 1 through the route.

5. When PE 1 receives the packet, it processes the packet as follows:

¡ If the packet header contains an End.DT4 or End.DT46 SID, PE 1 searches the local SID forwarding table for the SID and removes the outer IPv6 header. Then, PE 1 matches the packet to the public instance based on the SID, looks up the public network routing table, and forwards the packet to CE 1.

¡ If the packet header contains an End.DX4 SID, PE 1 searches the local SID forwarding table for the SID and removes the outer IPv6 header. Then, PE 1 forwards the packet to CE 1 according to the next hop and output interface bound to the SID.

SRv6 TE mode

This mode is also called SRv6 TE policy-based forwarding mode. In this mode, when a PE forwards a customer packet, it first searches for a matching SRv6 TE policy based on the packet attributes. Then, the PE adds an SRH to the packet. The SRH includes the destination SRv6 SID and the SID list of the SRv6 TE policy. Finally, the PE forwards the encapsulated packet based on the SRv6 TE policy.

The following modes are available to steer traffic to an SRv6 TE policy:

· Color—The device searches for an SRv6 TE policy that has the same color and endpoint address as the color and nexthop address of a BGP route. If a matching SRv6 TE policy exists, the device recurses the BGP route to that SRv6 TE policy. When the device receives packets that match the BGP route, it forwards the packets through the SRv6 TE policy.

· Tunnel policy—The device searches the tunnel policies for a matching SRv6 TE policy based on the next hop of a matching route. Configure a preferred tunnel or load sharing tunnel policy that uses the SRv6 TE policy. In this way, the SRv6 TE policy will be used as the public tunnel to carry the SRv6 PW that forwards the packets of customer network packets.

For more information about tunnel policies, see MPLS Configuration Guide. For more information about SRv6 TE policies, see "Configuring SRv6 TE policies."

SRv6 TE and SRv6 BE hybrid mode

In this mode, the PE preferentially uses the SRv6 TE mode to forward a packet. If no SRv6 TE policy is available for the packet, the PE performs IPv6 routing table lookup based on the encapsulated SRv6 SID, and forwards the packet in SRv6 BE mode.

Public network IP over SRv6 FRR

Public network IP over SRv6 Fast Reroute (FRR) is applicable to a dualhomed scenario, as shown in Figure 2. By using static BFD to detect the primary link, FRR enables a PE to use the backup link when the primary link fails. The PE then selects a new optimal route, and uses the new optimal route to forward traffic.

Public network IP over SRv6 supports IPv4 unicast route backup for IPv4 unicast route and IPv6 unicast route backup for IPv6 unicast route.

Figure 2 Network diagram of public network IP over SRv6 FRR

IPv4 unicast route backup for IPv4 unicast route and IPv6 unicast route backup for IPv6 unicast route use the same FRR mechanism. This section uses IPv4 unicast route backup for IPv4 unicast route as an example to illustrate the mechanism.

As shown in Figure 2, configure FRR on the ingress node PE 1, and specify the backup next hop as PE 3 for the public IPv4 route to CE 2. When PE 1 receives a BGP IPv4 unicast route to CE 2 from both PE 2 and PE 3, it uses the route from PE 2 as the primary path, and the route from PE 3 as the backup path.

Configure static BFD for public tunnels on PE 1 to detect the connectivity of the public tunnel from PE 1 to PE 2. When the tunnel PE 1—PE 2 operates correctly, traffic from CE 1 to CE 2 goes through the path CE 1—PE 1—PE 2—CE 2. When the tunnel fails, the traffic goes through the path CE 1—PE 1—PE 3—CE 2.

In this scenario, PE 1 is responsible for primary path detection and traffic switchover.

For more information about static BFD, see BFD configuration in High Availability Configuration Guide.

Restrictions: Hardware compatibility with public network IP over SRv6

In standard system operating mode, only the following cards support this feature:

Card category	Cards
CEPC	CEPC-CQ8L, CEPC-CQ8LA, CEPC-CQ8L1A, CEPC-CQ16L1
CSPEX	CSPEX-1802X, CSPEX-1802XA, CSPEX-2612XA, CSPEX-1812X-E, CSPEX-2304X-G, CSPEX-1502XA
SPE	RX-SPE200-E

In SDN-WAN system operating mode, only the following cards support this feature:

Card category	Cards
CEPC	CEPC-XP4LX, CEPC-XP24LX, CEPC-XP48RX, CEPC-CP4RX, CEPC-CP4RXA, CEPC-CP4RX-L, CEPC-CQ8L, CEPC-CQ8LA, CEPC-CQ8L1A, CEPC-CQ16L1
CSPEX	CSPEX-1304X, CSPEX-1404X, CSPEX-1502X, CSPEX-1504X, CSPEX-1504XA, CSPEX-1602X, CSPEX-1602XA, CSPEX-1804X, CSPEX-1512X, CSPEX-1612X, CSPEX-1812X, CSPEX-1802X, CSPEX-1802XA, CSPEX-2612XA, CSPEX-1812X-E, CSPEX-2304X-G, CSPEX-1502XA
SPE	RX-SPE200, RX-SPE200-E
OAA	IM-NGFWX-IV

Restrictions and guidelines: Public network IP over SRv6 configuration

In a public network IP over SRv6 scenario, the following routing policies cannot take effect on the routes received from a public network peer:

· Import routing policies specified by using the import route-policy command in public instance view, public instance IPv4 address family view, and public instance IPv6 address family view.

· Export routing policies specified by using the export route-policy command in public instance view, public instance IPv4 address family view, and public instance IPv6 address family view.

As a best practice, do not configure these routing policies.

You can use the import route-policy and export route-policy commands to deploy routing policies only in the scenarios that BGP routes are redistributed between the public network and a VPN instance. For more information about BGP route redistribution between the public network and a VPN instance, see MPLS L3VPN configuration in MPLS Configuration Guide.

Public network IP over SRv6 tasks at a glance

To configure public network IP over SRv6, perform the following tasks:

1. Configuring route exchange between a PE and a CE

Configure an IPv4 routing protocol (static routing, RIP, OSPF, IS-IS, EBGP, or IBGP) or an IPv6 routing protocol (IPv6 static routing, RIPng, OSPFv3, IPv6 IS-IS, EBGP, or IBGP) to exchange routes between a PE and a CE

On the CE, configure an IPv4 or IPv6 routing protocol to advertise routes of the local site to the PE. For more information about routing protocol configurations, see Layer 3—IP Routing Configuration Guide.

2. Configuring route exchange between PEs

a. Configuring an SRv6 SID

Perform this task to manually configure an End.DT4, End.DT6, End.DT46, End.DX4, or End.DX6 SID.

b. Applying a locator to a BGP instance

Perform this task to use BGP IPv4 or IPv6 unicast routes to advertise SRv6 SIDs in the specified locator.

c. Configuring PEs to exchange BGP IPv4 or IPv6 unicast routes

d. Configuring IPv6 peers to exchange SRv6 SIDs

This feature enables PEs to exchange End.DT4, End.DT6, End.DT46, End.DX4, or End.DX6 SIDs through BGP IPv4 or IPv6 unicast routes.

e. (Optional.) Configuring next hop-based dynamic End.DX4 or End.DX6 SID allocation for public network routes

f. (Optional.) Configuring BGP IPv4 or IPv6 unicast routes

For more information about configuring BGP IPv4 or IPv6 unicast routes, see BGP configuration in Layer 3—IP Routing Configuration Guide.

3. Configuring the route recursion mode

4. Specifying a source address for the outer IPv6 header of SRv6-encapsulated packets

This feature specifies the source address of the outer IPv6 header for SRv6 packets that are delivered between two public network sites over the backbone network.

5. Configuring public network IP over SRv6 FRR

Configuring an SRv6 SID

1. Enter system view.

system-view

2. Enable SRv6 and enter SRv6 view.

segment-routing ipv6

3. Configure a locator and enter SRv6 locator view.

locator locator-name [ ipv6-prefix ipv6-address prefix-length [ args args-length | static static-length ] * ]

4. Configure an opcode. Perform one of the following tasks:

¡ Configure an End.DT4 SID.

opcode { opcode | hex hex-opcode } end-dt4

¡ Configure an End.DT6 SID.

opcode { opcode | hex hex-opcode } end-dt6

¡ Configure an End.DT46 SID.

opcode { opcode | hex hex-opcode } end-dt46

¡ Configure an End.DX4 SID.

opcode { opcode | hex hex-opcode } end-dx4 interface interface-type interface-number nexthop nexthop-ipv4-address

An End.DX4 SID cannot be configured with different output interfaces or next hops.

¡ Configure an End.DX6 SID.

opcode { opcode | hex hex-opcode } end-dx6 interface interface-type interface-number nexthop nexthop-ipv6-address

An End.DX6 SID cannot be configured with different output interfaces or next hops.

Applying a locator to a BGP instance

About this task

In the public network IP over SRv6 scenario, use this feature in BGP IPv4 or IPv6 unicast address family view to apply for SRv6 SIDs for IPv4 or IPv6 routes.

Use this feature if the device will use End.DT4, End.DT6, End.DT46, End.DX4, or End.DX6 SIDs to deliver public network traffic across sites.

Prerequisites

Before you perform this task, you must create the specified locator.

Procedure

1. Enter system view.

system-view

2. Enter BGP instance view.

bgp as-number [ instance instance-name ]

3. Enter BGP IPv4 or IPv6 unicast address family view.

¡ Enter BGP IPv4 unicast address family view.

address-family ipv4 [ unicast ]

¡ Enter BGP IPv6 unicast address family view.

address-family ipv6 [ unicast ]

4. Apply a locator to the BGP instance.

segment-routing ipv6 locator locator-name [ auto-sid-disable ]

By default, no locator is applied to a BGP instance.

Configuring PEs to exchange BGP IPv4 or IPv6 unicast routes

Restrictions and guidelines

For more information about the commands in this task, see BGP in Layer 3—IP Routing Command Reference.

To ensure optimal route selection and SRv6 tunnel traffic forwarding, make sure a pair of PEs are not both IPv4 and IPv6 peers to each other.

Procedure

1. Enter system view.

system-view

2. Enter BGP instance view.

bgp as-number [ instance instance-name ]

3. Specify a remote PE as an IPv6 peer.

peer { group-name | ipv6-address [ prefix-length ] } as-number as-number

4. Specify a source interface (IPv6 address) for establishing TCP connections to an IPv6 peer or peer group.

peer { group-name | ipv6-address [ prefix-length ] } connect-interface interface-type interface-number

By default, BGP uses the output interface in the optimal route destined for a BGP peer or peer group as the source interface for establishing TCP connections.

5. Enter BGP IPv4 or IPv6 unicast address family view.

¡ Enter BGP IPv4 unicast address family view.

address-family ipv4 [ unicast ]

¡ Enter BGP IPv6 unicast address family view.

address-family ipv6 [ unicast ]

6. Enable BGP to exchange IPv4 or IPv6 unicast routing information with an IPv6 peer or peer group.

peer { group-name | ipv6-address [ prefix-length ] } enable

By default, BGP cannot exchange IPv4 or IPv6 unicast routing information with an IPv6 peer or peer group.

Configuring IPv6 peers to exchange SRv6 SIDs

About this task

Perform this task to configure IPv6 peers to exchange SRv6 SID information through BGP IPv4 or IPv6 unicast routes.

Procedure

1. Enter system view.

system-view

2. Enter BGP instance view.

bgp as-number [ instance instance-name ]

3. Enter BGP IPv4 or IPv6 unicast address family view.

¡ Enter BGP IPv4 unicast address family view.

address-family ipv4 [ unicast ]

¡ Enter BGP IPv6 unicast address family view.

address-family ipv6 [ unicast ]

4. Enable BGP to exchange SRv6 SID information with an IPv6 peer or peer group.

peer { group-name | ipv6-address [ prefix-length ] } prefix-sid

By default, BGP cannot exchange SRv6 SID information with an IPv6 peer or peer group.

Configuring next hop-based dynamic End.DX4 or End.DX6 SID allocation for public network routes

About this task

This feature is applicable to the public network IPv6 over SRv6 scenario.

By default, a PE allocates the same SID to all BGP public network routes. When the PE removes the SRv6 encapsulation from a received packet, it looks up the routing table of the public network based on the SID for an optimal route. To forward the packet to the next hop without looking up the routing table, configure this feature.

This feature dynamically allocates End.DX4 or End.DX6 SIDs to all next hops for the BGP public network IPv4 or IPv6 routes. When forwarding a packet, the PE searches for the output interface and next hop based on the End.DX4 or End.DX6 SID of the packet. Then, the PE directly forwards the packet out of the output interface to the next hop.

Restrictions and guidelines

This feature does not allocate End.DX4 or End.DX6 SIDs to direct routes.

Prerequisites

Before you perform this task in BGP IPv4 or IPv6 unicast address family view, execute the segment-routing ipv6 locator command in the same view to apply a locator to the view. This ensures successful dynamic End.DX4 or End.DX6 SID allocation.

Procedure

1. Enter system view.

system-view

2. Enter BGP instance view.

bgp as-number [ instance instance-name ]

3. Enter BGP IPv4 unicast address family view or BGP IPv6 unicast address family view.

¡ Enter BGP IPv4 unicast address family view.

address-family ipv4 [ unicast ]

¡ Enter BGP IPv6 unicast address family view.

address-family ipv6 [ unicast ]

4. Allocate End.DX4 or End.DX6 SIDs to the next hops of BGP public network routes.

¡ Allocate End.DX4 or End.DX6 SIDs to all next hops of BGP public network routes.

segment-routing ipv6 apply-sid all-nexthop

¡ Execute the following commands in sequence to allocate End.DX4 or End.DX6 SIDs to the specified next hop of BGP public network routes.

segment-routing ipv6 apply-sid specify-nexthop

nexthop nexthop-address interface interface-type interface-number

By default, public instance-based SID allocation is used for public network routes.

Configuring the route recursion mode

About this task

After a PE receives a customer packet destined for an SRv6 SID, it forwards the packet according to the route recursion mode.

· SRv6 BE mode—This mode is also called SID-based forwarding mode. In this mode, the PE first encapsulates the End.DT4, End.DT6, or End.DT46 SID into the packet. Then, the PE searches the IPv6 routing table based on the SID encapsulated in the packet to forward the packet.

· SRv6 TE mode—This mode is also called SRv6 TE policy-based forwarding mode. In this mode, the PE first searches for a matching SRv6 TE policy based on the packet attributes. Then, the PE adds an SRH to the packet. The SRH includes the End.DT4, End.DT6, or End.DT46 SID and the SID list of the SRv6 TE policy. Finally, the PE forwards the encapsulated packet through the SRv6 TE policy. For more information, see "Configuring SRv6 TE policies."

· SRv6 TE and SRv6 BE hybrid mode—In this mode, the PE preferentially uses the SRv6 TE mode to forward the packet. If no SRv6 TE policy is available for the packet, the PE forwards the packet in SRv6 BE mode.

· SRv6 TE and SRv6 BE FRR mode—This mode implements FRR by using the SRv6 TE path (primary path) and SRv6 BE path (backup path). If the SRv6 TE path fails or does not exist, traffic is immediately switched to the SRv6 BE path to ensure service continuity.

Procedure

1. Enter system view.

system-view

2. Enter BGP instance view.

bgp as-number [ instance instance-name ]

3. Enter BGP IPv4 or IPv6 unicast address family view.

¡ Enter BGP IPv4 unicast address family view.

address-family ipv4 [ unicast ]

¡ Enter BGP IPv6 unicast address family view.

address-family ipv6 [ unicast ]

4. Configure the route recursion mode.

segment-routing ipv6 { best-effort | traffic-engineering | traffic-engineering best-effort | traffic-engineering best-effort-backup }

By default, a PE searches the IPv6 routing table based on the next hop of a matching route to forward traffic.

Specifying a source address for the outer IPv6 header of SRv6-encapsulated packets

Restrictions and guidelines

To ensure correct traffic forwarding in the public network IPv6 over SRv6 scenario, you must specify a source address for the outer IPv6 header of SRv6-encapsulated packets.

You cannot specify a loopback address, link-local address, multicast address, or unspecified address as the source IPv6 address. You must specify an IPv6 address of the local device as the source IPv6 address, and make sure the IPv6 address has been advertised by a routing protocol. As a best practice, specify a loopback interface address of the local device as the source IPv6 address.

Procedure

1. Enter system view.

system-view

2. Enter SRv6 view.

segment-routing ipv6

3. Specify a source address for the outer IPv6 header of SRv6-encapsulated packets.

encapsulation source-address ipv6-address [ ip-ttl ttl-value ]

By default, no source address is specified for the outer IPv6 header of SRv6-encapsulated packets.

Configuring public network IP over SRv6 FRR

About this task

You can enable public network IP over SRv6 FRR by enabling FRR for a specific public network address family. Public network IP over SRv6 FRR enables the device to calculate backup routes for all BGP routes of the address family. If the device learns two unequal-cost routes destined for the same network from different peers, the optimal route is backed up by the other route. When the optimal route becomes unavailable, the device uses the backup route to forward traffic. At the same time, the device calculates a new optimal route and then uses it to direct traffic forwarding.

By default, the public instance IP routing table does not have SRv6 SID route information. As a result, FRR can only use the static BFD session for the locator network address to detect the primary path between PEs. If multiple address families of the public instance have used the same locator, FRR in these address families might use the same static BFD session to detect the primary path. Once the BFD session detects that the path is not available, the BGP routes in all these address families will perform path switching simultaneously.

For refined FRR management, the segment-routing ipv6 primary-path-detect sid-bfd command is provided in BGP IPv4 unicast address family view and BGP IPv6 unicast address family view. After this command is executed, when the device adds a BGP IPv4/IPv6 unicast route that contains an SRv6 SID to the public instance IP routing table, it adds the SRv6 SID as the next hop of the route. This allows FRR to automatically and preferentially associate the static BFD session for the SRv6 SID to detect the primary path. Once BFD detects that an SRv6 SID is not reachable, it triggers the BGP routes in only one address family to perform path switching. This mechanism provides a smaller control granularity for FRR.

Restrictions and guidelines

This feature might cause routing loops in certain conditions. Make sure you are fully aware of this feature when you use it on a live network.

The segment-routing ipv6 primary-path-detect sid-bfd command applies only to routes that use the SRv6 BE route recursion mode. If the route recursion mode is SRv6 TE and SRv6 BE hybrid, SRv6 TE and SRv6 BE FRR, or SRv6 TE and SRv6 BE multilevel FRR, this command takes effect only when the SRv6 TE path is not available.

Procedure

1. Enter system view.

system-view

2. Configure static BFD.

bfd static session-name [ peer-ipv6 ipv6-address [ vpn-instance vpn-instance-name ] source-ipv6 ipv6-address [ discriminator local local-value remote remote-value ] [ track-interface interface-type interface-number ] ]

If the segment-routing ipv6 primary-path-detect sid-bfd command is not executed, the addresses specified by the peer-ipv6 ipv6-address option and source-ipv6 ipv6-address option must be the locator subnet addresses advertised by the two peers of the link.

If the segment-routing ipv6 primary-path-detect sid-bfd command is executed, the addresses specified by the peer-ipv6 ipv6-address option and source-ipv6 ipv6-address option can be the SRv6 SIDs assigned by the two peers of the link in the public instance.

For more information about the bfd static command, see BFD commands in High Availability Command Reference.

3. Return to system view.

quit

4. Enter BGP instance view.

bgp as-number [ instance instance-name ]

5. Configure BGP FRR to use BFD to detect next hop connectivity for the primary route in control packet mode or echo packet mode.

primary-path-detect bfd { ctrl | echo }

By default, BGP FRR uses ARP to detect the connectivity to the next hop of the primary route.

For more information about this command, see BGP commands in Layer 3—IP Routing Command Reference.

6. (Optional.) Enable using the static BFD session for the SRv6 SID to detect the reachability of the primary path for public network IP over SRv6 FRR.

¡ Execute the following commands in sequence to enable this feature in BGP IPv4 unicast address family view:

address-family ipv4 [ unicast ]

segment-routing ipv6 primary-path-detect sid-bfd

¡ Execute the following commands in sequence to enable this feature in BGP IPv6 unicast address family view:

address-family ipv6 [ unicast ]

segment-routing ipv6 primary-path-detect sid-bfd

By default, the device detects the reachability of the FRR primary path by using the static BFD session for the locator.

7. Enable FRR for the address family.

pic

By default, FRR is disabled for a BGP address family.

For more information about this command, see BGP commands in Layer 3—IP Routing Command Reference.

Display and maintenance commands for public network IP over SRv6

Resetting BGP sessions

For BGP setting changes to take effect, you must reset BGP sessions. Resetting BGP sessions updates BGP routing information by tearing down and re-establishing the BGP sessions.

Execute the command in this section in user view. For more information about the command, see BGP in Layer 3—IP Routing Command Reference.

‌

Task	Command
Reset BGP sessions of the BGP IPv6 unicast address family.	reset bgp [ instance instance-name ] { as-number \| ipv6-address [ prefix-length ] \| all \| external \| group group-name \| internal } ipv6 [ unicast ]

‌

Displaying and maintaining the running status of public network IP over SRv6

Execute display commands in any view and reset commands in user view.

For more information about the commands in this section, see BGP in Layer 3—IP Routing Command Reference.

Task	Command
Display BGP IPv6 unicast route information.	display bgp [ instance instance-name ] routing-table ipv6 [ unicast ] [ ipv6-address prefix-length [ advertise-info ] \| as-path-acl as-path-acl-number \| community-list { { basic-community-list-number \| comm-list-name } [ whole-match ] \| adv-community-list-number } \| peer ipv6-address { advertised-routes \| received-routes } [ ipv6-address prefix-length \| statistics ] \| statistics ]
Clear flap statistics for BGP IPv6 unicast routes.	reset bgp [ instance instance-name ] flap-info ipv6 [ unicast ] [ ipv6-address prefix-length \| as-path-acl as-path-acl-number \| peer ipv6-address [ prefix-length ] ]

‌

Public network IP over SRv6 configuration examples

Example: Configuring public network IPv6 over SRv6 in SRv6 BE mode

Network configuration

As shown in Figure 3, the backbone network is an IPv6 network. Deploy public network IPv6 over SRv6 between PE 1 and PE 2 and use an SRv6 tunnel to transmit IPv4 traffic between the PEs.

· Configure EBGP to exchange customer site routing information between the CEs and PEs.

· Configure IPv6 IS-IS on the PEs in the same AS to realize IPv6 network connectivity.

· Configure IBGP to exchange IPv4 routing information between the PEs.

Figure 3 Network diagram

‌

Table 1 Interface and IP address assignment

Device	Interface	IP address	Device	Interface	IP address
CE 1	XGE3/1/1	111::1/96	PE 2	Loop0	3::3/128
PE 1	Loop0	1::1/128		XGE3/1/1	222::2/96
	XGE3/1/1	111::2/96		XGE3/1/2	2002::1/96
	XGE3/1/2	2001::1/96	CE 2	XGE3/1/1	222::1/96
P	Loop0	2::2/128
	XGE3/1/1	2001::2/96
	XGE3/1/2	2002::2/96

‌

Prerequisites

Configure IP addresses for the interfaces (including the Loopback interfaces), as shown in Figure 3.

Procedure

1. Configure IPv6 IS-IS on the PEs and device P for network connectivity between the devices:

# Configure PE 1.

<PE1> system-view

[PE1] isis 1

[PE1-isis-1] is-level level-1

[PE1-isis-1] cost-style wide

[PE1-isis-1] network-entity 10.1111.1111.1111.00

[PE1-isis-1] address-family ipv6 unicast

[PE1-isis-1-ipv6] quit

[PE1-isis-1] quit

[PE1] interface loopback 0

[PE1-LoopBack0] isis ipv6 enable 1

[PE1-LoopBack0] quit

[PE1] interface ten-gigabitethernet 3/1/2

[PE1-Ten-GigabitEthernet3/1/2] isis ipv6 enable

[PE1-Ten-GigabitEthernet3/1/2] quit

# Configure P.

<P> system-view

[P] isis

[P-isis-1] is-level level-1

[P-isis-1] cost-style wide

[P-isis-1] network-entity 10.2222.2222.2222.00

[P-isis-1] address-family ipv6 unicast

[P-isis-1-ipv6] quit

[P-isis-1] quit

[P] interface loopback 0

[P-LoopBack0] isis ipv6 enable

[P-LoopBack0] quit

[P] interface ten-gigabitethernet 3/1/1

[P-Ten-GigabitEthernet3/1/1] isis ipv6 enable

[P-Ten-GigabitEthernet3/1/1] quit

[P] interface ten-gigabitethernet 3/1/2

[P-Ten-GigabitEthernet3/1/2] isis ipv6 enable

[P-Ten-GigabitEthernet3/1/2] quit

# Configure PE 2.

<PE2> system-view

[PE2] isis

[PE2-isis-1] is-level level-1

[PE2-isis-1] cost-style wide

[PE2-isis-1] network-entity 10.3333.3333.3333.00

[PE2-isis-1] address-family ipv6 unicast

[PE2-isis-1-ipv6] quit

[PE2-isis-1] quit

[PE2] interface loopback 0

[PE2-LoopBack0] isis ipv6 enable

[PE2-LoopBack0] quit

[PE2] interface ten-gigabitethernet 3/1/2

[PE2-Ten-GigabitEthernet3/1/2] isis ipv6 enable

[PE2-Ten-GigabitEthernet3/1/2] quit

2. Set up an EBGP peer relationship between each PE and its local CE and distribute CE routes to EBGP:

# Configure CE 1.

<CE1> system-view

[CE1] bgp 65410

[CE1-bgp-default] peer 111::2 as-number 100

[CE1-bgp-default] address-family ipv6 unicast

[CE1-bgp-default-ipv6] peer 111::2 enable

[CE1-bgp-default-ipv6] import-route direct

[CE1-bgp-default-ipv6] quit

[CE1-bgp-default] quit

# Configure CE 2 in the same way as CE 1 is configured. (Details not shown.)

# Configure PE 1.

[PE1] bgp 100

[PE1-bgp-default] router-id 1.1.1.1

[PE1-bgp-default] peer 111::1 as-number 65410

[PE1-bgp-default] address-family ipv6 unicast

[PE1-bgp-default-ipv6] peer 111::1 enable

[PE1-bgp-default-ipv6] import-route direct

[PE1-bgp-default-ipv6] quit

[PE1-bgp-default] quit

# Configure PE 2 in the same way PE 1 is configured. (Details not shown.)

3. Set up an IBGP peer relationship between PE 1 and PE 2:

# Configure PE 1.

[PE1] bgp 100

[PE1-bgp-default] peer 3::3 as-number 100

[PE1-bgp-default] peer 3::3 connect-interface loopback 0

[PE1-bgp-default] address-family ipv6 unicast

[PE1-bgp-default-ipv6] peer 3::3 enable

[PE1-bgp-default-ipv6] quit

[PE1-bgp-default] quit

# Configure PE 2.

[PE2] bgp 100

[PE2-bgp-default] peer 1::1 as-number 100

[PE2-bgp-default] peer 1::1 connect-interface loopback 0

[PE2-bgp-default] address-family ipv6 unicast

[PE2-bgp-default-ipv6] peer 1::1 enable

[PE2-bgp-default-ipv6] quit

[PE2-bgp-default] quit

4. Specify a source address for the outer IPv6 header of SRv6-encapsulated public network IP packets on PE 1 and PE 2:

# Configure PE 1.

[PE1] segment-routing ipv6

[PE1-segment-routing-ipv6] encapsulation source-address 1::1

# Configure PE 2.

[PE2] segment-routing ipv6

[PE2-segment-routing-ipv6] encapsulation source-address 3::3

5. Configure the destination address (End.DT4 SID) of the outer IPv6 header for SRv6-encapsulated public network IP packets:

# Configure PE 1.

[PE1-segment-routing-ipv6] locator aaa ipv6-prefix 1:2::1:0 96 static 8

[PE1-segment-routing-ipv6-locator-aaa] quit

[PE1-segment-routing-ipv6] quit

[PE1] isis 1

[PE1-isis-1] address-family ipv6 unicast

[PE1-isis-1-ipv6] segment-routing ipv6 locator aaa

[PE1-isis-1-ipv6] quit

[PE1-isis-1] quit

# Configure PE 2.

[PE2-segment-routing-ipv6] locator bbb ipv6-prefix 6:5::1:0 96 static 8

[PE2-segment-routing-ipv6-locator-bbb] quit

[PE2-segment-routing-ipv6] quit

[PE2] isis 1

[PE2-isis-1] address-family ipv6 unicast

[PE2-isis-1-ipv6] segment-routing ipv6 locator bbb

[PE2-isis-1-ipv6] quit

[PE2-isis-1] quit

6. Add End.DT4 SIDs to public network routes of the customer sites on PE 1 and PE 2:

# Configure PE 1.

[PE1] bgp 100

[PE1-bgp-default] address-family ipv6 unicast

[PE1-bgp-default-ipv6] segment-routing ipv6 locator aaa

[PE1-bgp-default-ipv6] quit

[PE1-bgp-default] quit

# Configure PE 2.

[PE2] bgp 100

[PE2-bgp-default] address-family ipv6 unicast

[PE2-bgp-default-ipv6] segment-routing ipv6 locator bbb

[PE2-bgp-default-ipv6] quit

[PE2-bgp-default] quit

7. Enable IPv6 peers on the PEs to exchange End.DT4 SIDs and enable SRv6 BE route recursion mode:

# Configure PE 1.

[PE1] bgp 100

[PE1-bgp-default] address-family ipv6 unicast

[PE1-bgp-default-ipv6] peer 3::3 prefix-sid

[PE1-bgp-default-ipv6] segment-routing ipv6 best-effort

[PE1-bgp-default-ipv6] quit

[PE1-bgp-default] quit

# Configure PE 2.

[PE2] bgp 100

[PE2-bgp-default] address-family ipv6 unicast

[PE2-bgp-default-ipv6] peer 1::1 prefix-sid

[PE2-bgp-default-ipv6] segment-routing ipv6 best-effort

[PE2-bgp-default-ipv6] quit

[PE2-bgp-default] quit

Verifying the configuration

# Display IPv6 routing table information on the PEs and verify that each PE has a route destined for the remote CE and the next hop of the route is the End.DT4 SID of the route. This step uses PE 1 as an example.

[PE1] display ipv6 routing-table 222::1 96

Summary count : 1

Destination: 222::/96 Protocol : BGP4+

NextHop : 6:5:: Preference: 255

Interface : XGE3/1/2 Cost : 0

# Verify that CE 1 and CE 2 can ping each other. (Details not shown.)

11-Segment Routing Configuration Guide

About public network IP over SRv6

SRv6 BE mode

SRv6 TE mode

SRv6 TE and SRv6 BE hybrid mode

Public network IP over SRv6 tasks at a glance

About this task

Prerequisites

Procedure

Restrictions and guidelines

Procedure

About this task

Procedure

About this task

Restrictions and guidelines

Prerequisites

Procedure

About this task

Procedure

Specifying a source address for the outer IPv6 header of SRv6-encapsulated packets

Restrictions and guidelines

Procedure

About this task

Restrictions and guidelines

Procedure

Display and maintenance commands for public network IP over SRv6

Network configuration

Prerequisites

Procedure

Verifying the configuration

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

Company Information

News & Events

Contact Us