H3C S6890 Switch Series
DRNI Configuration Examples

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Document version: 6W100-20190628

 

Contents

Introduction· 1

Prerequisites· 1

Example: Configuring DRNI at the access Layer 1

Network configuration· 1

Analysis· 2

Software versions used· 3

Restrictions and guidelines· 3

Interface restrictions and guidelines· 3

DRNI restrictions and guidelines· 3

VRRP restrictions and guidelines· 3

Procedures· 3

Configuring Device A· 3

Configuring Device B· 5

Configuring Device C·· 7

Configuring Device D·· 9

Configuring Device E· 10

Configuring Device F· 11

Verifying the configuration· 12

Configuration files· 14

Example: Configuring DRNI at the distribution Layer 20

Network configuration· 20

Analysis· 21

Software versions used· 22

Restrictions and guidelines· 22

Interface restrictions and guidelines· 22

DRNI restrictions and guidelines· 22

VRRP restrictions and guidelines· 22

Procedures· 22

Configuring Device A· 22

Configuring Device B· 25

Configuring Device C·· 28

Configuring Device D·· 29

Configuring Device E· 29

Verifying the configuration· 30

Configuration files· 33

Related documentation· 38

 

Introduction

This document provides DRNI configuration examples.

Distributed Resilient Network Interconnect (DRNI) virtualizes two physical devices into one system through multichassis link aggregation. The standard for DRNI is IEEE P802.1AX-REV™/D4.4c, Draft Standard for Local and Metropolitan Area Networks.

Prerequisites

The configuration examples were created and verified in a lab environment, and all the devices were started with the factory default configuration. When you are working on a live network, make sure you understand the potential impact of every command on your network.

The following information is provided based on the assumption that you have basic knowledge of DRNI.

Example: Configuring DRNI at the access Layer

Network configuration

As shown in Figure 1:

·          Configure Device A and Device B as a DR system to establish one multichassis aggregate link with Device F and one with Device C and Device D.

·          Set up a keepalive link between Ten-GigabitEthernet 1/0/5 of Device A and Ten-GigabitEthernet 1/0/5 of Device B, and exclude the interfaces from the shutdown action by DRNI MAD.

·          Configure two VRRP groups on Device C and Device D to provide gateway services for VLAN 10 and VLAN 20.

¡  Configure VRRP group 1 to provide gateway services for hosts in VLAN 10 (Area A). Add Device C and Device D to the group as the master and backup devices, respectively.

¡  Configure VRRP group 2 to provide gateway services for hosts in VLAN 20 (Area B). Add Device D and Device C to the group as the master and backup devices, respectively.

·          Configure OSPF on Device C, Device D, and Device E for the hosts to communicate with external networks at Layer 3.

Figure 1 Network diagram

 

Device	Interface	IP address	Device	Interface	IP address
Device A	XGE 1/0/5	1.1.1.1/24	Device B	XGE1/0/5	1.1.1.2/24
Device C	VLAN-interface 100	100.1.1.1/24	Device D	VLAN-interface 100	200.1.1.1/24
	VLAN-interface 10	10.1.1.1/24		VLAN-interface 10	10.1.1.2/24
	VLAN-interface 20	20.1.1.1/24		VLAN-interface 20	20.1.1.2/24
	Virtual IP 1	10.1.1.100/24		Virtual IP 1	10.1.1.100/24
	Virtual IP 2	20.1.1.100/24		Virtual IP 2	20.1.1.100/24
Device E	VLAN-interface 100	100.1.1.2/24
	VLAN-interface 200	200.1.1.2/24
	VLAN-interface 30	30.1.1.1/24

 

Analysis

For the secondary DR device to monitor the state of the primary device, establish a Layer 3 keepalive link between the DR member devices.

To balance traffic between two VRRP gateway devices, you can assign them to two VRRP groups with different priorities. In this example, Device C is assigned a higher priority than Device D in VRRP group 1 so Device C can become the master in this group. Device D is assigned a higher priority than Device C in VRRP group 2 so Device D can become the master in this group.

Software versions used

This configuration example was created and verified on S6890-CMW710-R2712.

Restrictions and guidelines

Interface restrictions and guidelines

By default, interfaces on S6890 switches are disabled (in ADM or Administratively Down state). To have an interface operate, you must use the undo shutdown command to enable that interface.

DRNI restrictions and guidelines

For the DR member devices to be identified as one DR system, you must configure the same DR system MAC address and DR system priority on them. You must assign different DR system numbers to the DR member devices.

A DR member device can have only one IPP.

For correct keepalive detection, you must exclude the interfaces used for keepalive detection from the shutdown action by DRNI MAD.

VRRP restrictions and guidelines

You cannot specify the virtual IP address as any of the following IP addresses:

·          All-zero address (0.0.0.0).

·          Broadcast address (255.255.255.255).

·          Loopback address.

·          IP address of other than Class A, Class B, and Class C.

·          Invalid IP address (for example, 0.0.0.1).

The virtual IP address of an IPv4 VRRP group must be on the same subnet as the downlink interface IP addresses of the VRRP group members to ensure successful traffic forwarding.

Procedures

Configuring Device A

# Configure DR system settings.

<DeviceA> system-view

[DeviceA] drni system-mac 1-1-1

Changing the system MAC might flap the intra-portal link and cause DR system setup failure. Continue? [Y/N]:y

[DeviceA] drni system-number 1

Changing the system number might flap the intra-portal link and cause DR system setup failure. Continue? [Y/N]:y

[DeviceA] drni system-priority 123

Changing the system priority might flap the intra-portal link and cause DR system setup failure. Continue? [Y/N]:y

# Configure DR keepalive packet parameters.

[DeviceA] drni keepalive ip destination 1.1.1.2 source 1.1.1.1

# Configure Ten-GigabitEthernet 1/0/5 as a routed (Layer 3) interface and assign the interface an IP address. The IP address will be used as the source IP address of keepalive packets.

[DeviceA] interface ten-gigabitethernet 1/0/5

[DeviceA-Ten-GigabitEthernet1/0/5] port link-mode route

[DeviceA-Ten-GigabitEthernet1/0/5] ip address 1.1.1.1 24

[DeviceA-Ten-GigabitEthernet1/0/5] quit

# Exclude the interface used for DR keepalive detection (Ten-GigabitEthernet 1/0/5) from the shutdown action by DRNI MAD.

[DeviceA] mad exclude interface ten-gigabitethernet 1/0/5

# Create VLAN 10 and VLAN 20.

[DeviceA] vlan 10

[DeviceA-vlan10] quit

[DeviceA] vlan 20

[DeviceA-vlan20] quit

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 1.

[DeviceA] interface bridge-aggregation 1

[DeviceA-Bridge-Aggregation1] link-aggregation mode dynamic

[DeviceA-Bridge-Aggregation1] quit

# Assign Ten-GigabitEthernet 1/0/6 and Ten-GigabitEthernet 1/0/7 to aggregation group 1.

[DeviceA] interface ten-gigabitethernet 1/0/6

[DeviceA-Ten-GigabitEthernet1/0/6] port link-aggregation group 1

[DeviceA-Ten-GigabitEthernet1/0/6] quit

[DeviceA] interface ten-gigabitethernet 1/0/7

[DeviceA-Ten-GigabitEthernet1/0/7] port link-aggregation group 1

[DeviceA-Ten-GigabitEthernet1/0/7] quit

# Set the link type of Bridge-Aggregation 1 to trunk and assign it to VLAN 10 and VLAN 20.

[DeviceA] interface bridge-aggregation 1

[DeviceA-Bridge-Aggregation1] port link-type trunk

Configuring Ten-GigabitEthernet1/0/6 done.

Configuring Ten-GigabitEthernet1/0/7 done.

[DeviceA-Bridge-Aggregation1] port trunk permit vlan 10 20

Configuring Ten-GigabitEthernet1/0/6 done.

Configuring Ten-GigabitEthernet1/0/7 done.

[DeviceA-Bridge-Aggregation1] quit

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 3 and specify it as the IPP.

[DeviceA] interface bridge-aggregation 3

[DeviceA-Bridge-Aggregation3] link-aggregation mode dynamic

[DeviceA-Bridge-Aggregation3] port drni intra-portal-port 1

[DeviceA-Bridge-Aggregation3] quit

# Assign Ten-GigabitEthernet 1/0/3 and Ten-GigabitEthernet 1/0/4 to aggregation group 3.

[DeviceA] interface ten-gigabitethernet 1/0/3

[DeviceA-Ten-GigabitEthernet1/0/3] port link-aggregation group 3

[DeviceA-Ten-GigabitEthernet1/0/3] quit

[DeviceA] interface ten-gigabitethernet 1/0/4

[DeviceA-Ten-GigabitEthernet1/0/4] port link-aggregation group 3

[DeviceA-Ten-GigabitEthernet1/0/4] quit

# Set the link type of Bridge-Aggregation 3 to trunk and assign it to VLAN 10 and VLAN 20.

[DeviceA] interface bridge-aggregation 3

[DeviceA-Bridge-Aggregation3] port link-type trunk

Configuring Ten-GigabitEthernet1/0/3 done.

Configuring Ten-GigabitEthernet1/0/4 done.

[DeviceA-Bridge-Aggregation3] port trunk permit vlan 10 20

Configuring Ten-GigabitEthernet1/0/3 done.

Configuring Ten-GigabitEthernet1/0/4 done.

[DeviceA-Bridge-Aggregation3] quit

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 4 and assign it to DR group 4.

[DeviceA] interface bridge-aggregation 4

[DeviceA-Bridge-Aggregation4] link-aggregation mode dynamic

[DeviceA-Bridge-Aggregation4] port drni group 4

[DeviceA-Bridge-Aggregation4] quit

# Assign Ten-GigabitEthernet 1/0/1 and Ten-GigabitEthernet 1/0/2 to aggregation group 4.

[DeviceA] interface ten-gigabitethernet 1/0/1

[DeviceA-Ten-GigabitEthernet1/0/1] port link-aggregation group 4

[DeviceA-Ten-GigabitEthernet1/0/1] quit

[DeviceA] interface ten-gigabitethernet 1/0/2

[DeviceA-Ten-GigabitEthernet1/0/2] port link-aggregation group 4

[DeviceA-Ten-GigabitEthernet1/0/2] quit

# Set the link type of Bridge-Aggregation 4 to trunk and assign it to VLAN 10 and VLAN 20.

[DeviceA] interface bridge-aggregation 4

[DeviceA-Bridge-Aggregation4] port link-type trunk

Configuring Ten-GigabitEthernet1/0/1 done.

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceA-Bridge-Aggregation4] port trunk permit vlan 10 20

Configuring Ten-GigabitEthernet1/0/1 done.

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceA-Bridge-Aggregation4] quit

Configuring Device B

# Configure DR system settings.

<DeviceB> system-view

[DeviceB] drni system-mac 1-1-1

Changing the system MAC might flap the intra-portal link and cause DR system setup failure. Continue? [Y/N]:y

[DeviceB] drni system-number 2

Changing the system number might flap the intra-portal link and cause DR system setup failure. Continue? [Y/N]:y

[DeviceB] drni system-priority 123

Changing the system priority might flap the intra-portal link and cause DR system setup failure. Continue? [Y/N]:y

# Configure DR keepalive packet parameters.

[DeviceB] drni keepalive ip destination 1.1.1.1 source 1.1.1.2

# Configure Ten-GigabitEthernet 1/0/5 as a routed (Layer 3) interface and assign the interface an IP address. The IP address will be used as the source IP address of keepalive packets.

[DeviceB] interface ten-gigabitethernet 1/0/5

[DeviceB-Ten-GigabitEthernet1/0/5] port link-mode route

[DeviceB-Ten-GigabitEthernet1/0/5] ip address 1.1.1.2 24

[DeviceB-Ten-GigabitEthernet1/0/5] quit

# Exclude the interface used for DR keepalive detection (Ten-GigabitEthernet 1/0/5) from the shutdown action by DRNI MAD.

[DeviceB] mad exclude interface ten-gigabitethernet 1/0/5

# Create VLAN 10 and VLAN 20.

[DeviceB] vlan 10

[DeviceB-vlan10] quit

[DeviceB] vlan 20

[DeviceB-vlan20] quit

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 2.

[DeviceB] interface bridge-aggregation 2

[DeviceB-Bridge-Aggregation2] link-aggregation mode dynamic

[DeviceB-Bridge-Aggregation2] quit

# Assign Ten-GigabitEthernet 1/0/6 and Ten-GigabitEthernet 1/0/7 to aggregation group 2.

[DeviceB] interface ten-gigabitethernet 1/0/6

[DeviceB-Ten-GigabitEthernet1/0/6] port link-aggregation group 2

[DeviceB-Ten-GigabitEthernet1/0/6] quit

[DeviceB] interface ten-gigabitethernet 1/0/7

[DeviceB-Ten-GigabitEthernet1/0/7] port link-aggregation group 2

[DeviceB-Ten-GigabitEthernet1/0/7] quit

# Set the link type of Bridge-Aggregation 2 to trunk and assign it to VLAN 10 and VLAN 20.

[DeviceB] interface bridge-aggregation 2

[DeviceB-Bridge-Aggregation2] port link-type trunk

Configuring Ten-GigabitEthernet1/0/6 done.

Configuring Ten-GigabitEthernet1/0/7 done.

[DeviceB-Bridge-Aggregation2] port trunk permit vlan 10 20

Configuring Ten-GigabitEthernet1/0/6 done.

Configuring Ten-GigabitEthernet1/0/7 done.

[DeviceB-Bridge-Aggregation2] quit

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 3 and specify it as the IPP.

[DeviceB] interface bridge-aggregation 3

[DeviceB-Bridge-Aggregation3] link-aggregation mode dynamic

[DeviceB-Bridge-Aggregation3] port drni intra-portal-port 1

[DeviceB-Bridge-Aggregation3] quit

# Assign Ten-GigabitEthernet 1/0/3 and Ten-GigabitEthernet 1/0/4 to aggregation group 3.

[DeviceB] interface ten-gigabitethernet 1/0/3

[DeviceB-Ten-GigabitEthernet1/0/3] port link-aggregation group 3

[DeviceB-Ten-GigabitEthernet1/0/3] quit

[DeviceB] interface ten-gigabitethernet 1/0/4

[DeviceB-Ten-GigabitEthernet1/0/4] port link-aggregation group 3

[DeviceB-Ten-GigabitEthernet1/0/4] quit

# Set the link type of Bridge-Aggregation 3 to trunk and assign it to VLAN 10 and VLAN 20.

[DeviceB] interface bridge-aggregation 3

[DeviceB-Bridge-Aggregation3] port link-type trunk

Configuring Ten-GigabitEthernet1/0/3 done.

Configuring Ten-GigabitEthernet1/0/4 done.

[DeviceB-Bridge-Aggregation3] port trunk permit vlan 10 20

Configuring Ten-GigabitEthernet1/0/3 done.

Configuring Ten-GigabitEthernet1/0/4 done.

[DeviceB-Bridge-Aggregation3] quit

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 4 and assign it to DR group 4.

[DeviceB] interface bridge-aggregation 4

[DeviceB-Bridge-Aggregation4] link-aggregation mode dynamic

[DeviceB-Bridge-Aggregation4] port drni group 4

[DeviceB-Bridge-Aggregation4] quit

# Assign Ten-GigabitEthernet 1/0/1 and Ten-GigabitEthernet 1/0/2 to aggregation group 4.

[DeviceB] interface ten-gigabitethernet 1/0/1

[DeviceB-Ten-GigabitEthernet1/0/1] port link-aggregation group 4

[DeviceB-Ten-GigabitEthernet1/0/1] quit

[DeviceB] interface ten-gigabitethernet 1/0/2

[DeviceB-Ten-GigabitEthernet1/0/2] port link-aggregation group 4

[DeviceB-Ten-GigabitEthernet1/0/2] quit

# Set the link type of Bridge-Aggregation 4 to trunk and assign it to VLAN 10 and VLAN 20.

[DeviceB] interface bridge-aggregation 4

[DeviceB-Bridge-Aggregation4] port link-type trunk

Configuring Ten-GigabitEthernet1/0/1 done.

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceB-Bridge-Aggregation4] port trunk permit vlan 10 20

Configuring Ten-GigabitEthernet1/0/1 done.

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceB-Bridge-Aggregation4] quit

Configuring Device C

# Create VLAN 10, VLAN 20, and VLAN 100.

<DeviceC> system-view

[DeviceC] vlan 10

[DeviceC-vlan10] quit

[DeviceC] vlan 20

[DeviceC-vlan20] quit

[DeviceC] vlan 100

# Assign Ten-GigabitEthernet 1/0/3 to VLAN 100.

[DeviceC] vlan 100

[DeviceC-vlan100] port ten-gigabitethernet 1/0/3

[DeviceC-vlan100] quit

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 1.

[DeviceC] interface bridge-aggregation 1

[DeviceC-Bridge-Aggregation1] link-aggregation mode dynamic

[DeviceC-Bridge-Aggregation1] quit

# Assign Ten-GigabitEthernet 1/0/1 and Ten-GigabitEthernet1/0/2 to aggregation group 1.

[DeviceC] interface range ten-gigabitethernet 1/0/1 to ten-gigabitethernet 1/0/2

[DeviceC-if-range] port link-aggregation group 1

[DeviceC-if-range] quit

# Set the link type of Bridge-Aggregation 1 to trunk and assign it to VLAN 10 and VLAN 20.

[DeviceC] interface bridge-aggregation 1

[DeviceC-Bridge-Aggregation1] port link-type trunk

Configuring Ten-GigabitEthernet1/0/1 done.

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceC-Bridge-Aggregation1] port trunk permit vlan 10 20

Configuring Ten-GigabitEthernet1/0/1 done.

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceC-Bridge-Aggregation1] quit

# Create uplink interface VLAN-interface 100 and assign it an IP address.

[DeviceC] interface vlan-interface 100

[DeviceC-Vlan-interface100] ip address 100.1.1.1 24

[DeviceC-Vlan-interface100] quit

# Create VLAN-interface 10 and VLAN-interface 20 and assign an IP address to each of them.

[DeviceC] interface vlan-interface 10

[DeviceC-vlan-interface10] ip address 10.1.1.1 24

[DeviceC-vlan-interface10] quit

[DeviceC] interface vlan-interface 20

[DeviceC-vlan-interface20] ip address 20.1.1.1 24

[DeviceC-vlan-interface20] quit

# Create VRRP group 1 on VLAN-interface 10 and set its virtual IP address to 10.1.1.100.

[DeviceC] interface vlan-interface 10

[DeviceC-Vlan-interface10] vrrp vrid 1 virtual-ip 10.1.1.100

# Set the priority of Device C to 200 for it to become the master in VRRP group 1.

[DeviceC-Vlan-interface10] vrrp vrid 1 priority 200

[DeviceC-Vlan-interface10] quit

# Create VRRP group 2 on VLAN-interface 20 and set its virtual IP address to 20.1.1.100.

[DeviceC] interface vlan-interface 20

[DeviceC-Vlan-interface20] vrrp vrid 2 virtual-ip 20.1.1.100

[DeviceC-vlan-interface20] quit

# Configure Device C to operate in preemptive mode in VRRP group 1. Set the preemption delay to 500 centiseconds to avoid frequent status switchover.

[DeviceC] interface vlan-interface 10

[DeviceC-Vlan-interface10] vrrp vrid 1 preempt-mode delay 500

[DeviceC-Vlan-interface10] quit

# Create track entry 1 to monitor the upstream link status of Ten-GigabitEthernet 1/0/3.

[DeviceC] track 1 interface ten-gigabitethernet 1/0/3

# Configure Device C in VRRP group 1 to monitor track entry 1, and decrease its priority by 150 when the track entry transits to Negative.

[DeviceC] interface vlan-interface 10

[DeviceC-Vlan-interface10] vrrp vrid 1 track 1 priority reduced 150

[DeviceC-Vlan-interface10] quit

# Configure OSPF.

[DeviceC] ospf

[DeviceC-ospf-1] area 0

[DeviceC-ospf-1-area-0.0.0.0] network 10.1.1.0 0.0.0.255

[DeviceC-ospf-1-area-0.0.0.0] network 20.1.1.0 0.0.0.255

[DeviceC-ospf-1-area-0.0.0.0] network 100.1.1.0 0.0.0.255

[DeviceC-ospf-1-area-0.0.0.0] quit

[DeviceC-ospf-1] quit

Configuring Device D

# Create VLAN 10, VLAN 20, and VLAN 200.

<DeviceD> system-view

[DeviceD] vlan 10

[DeviceD-vlan10] quit

[DeviceD] vlan 20

[DeviceD-vlan20] quit

[DeviceD] vlan 200

# Assign Ten-GigabitEthernet 1/0/3 to VLAN 200.

[DeviceD] vlan 200

[DeviceD-vlan200] port ten-gigabitethernet 1/0/3

[DeviceD-vlan200] quit

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 2.

[DeviceD] interface bridge-aggregation 2

[DeviceD-Bridge-Aggregation2] link-aggregation mode dynamic

[DeviceD-Bridge-Aggregation2] quit

# Assign Ten-GigabitEthernet 1/0/1 and Ten-GigabitEthernet 1/0/2 to aggregation group 2.

[DeviceD] interface range ten-gigabitethernet 1/0/1 to ten-gigabitethernet 1/0/2

[DeviceD-if-range] port link-aggregation group 2

[DeviceD-if-range] quit

# Set the link type of Bridge-Aggregation 2 to trunk and assign it to VLAN 10 and VLAN 20.

[DeviceD] interface bridge-aggregation 2

[DeviceD-Bridge-Aggregation2] port link-type trunk

Configuring Ten-GigabitEthernet1/0/1 done.

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceD-Bridge-Aggregation2] port trunk permit vlan 10 20

Configuring Ten-GigabitEthernet1/0/1 done.

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceD-Bridge-Aggregation2] quit

# Create uplink interface VLAN-interface 200 and assign it an IP address.

[DeviceD] interface vlan-interface 200

[DeviceD-Vlan-interface200] ip address 200.1.1.1 24

[DeviceD-Vlan-interface200] quit

# Create VLAN-interface 10 and VLAN-interface 20 and assign an IP address to each of them.

[DeviceD] interface vlan-interface 10

[DeviceD-vlan-interface10] ip address 10.1.1.2 24

[DeviceD-vlan-interface10] quit

[DeviceD] interface vlan-interface 20

[DeviceD-vlan-interface20] ip address 20.1.1.2 24

[DeviceD-vlan-interface20] quit

# Create VRRP group 1 on VLAN-interface 10 and set its virtual IP address to 10.1.1.100.

[DeviceD] interface vlan-interface 10

[DeviceD-Vlan-interface10] vrrp vrid 1 virtual-ip 10.1.1.100

[DeviceD-vlan-interface10] quit

# Create VRRP group 2 on VLAN-interface 20 and set its virtual IP address to 20.1.1.100.

[DeviceD] interface vlan-interface 20

[DeviceD-Vlan-interface20] vrrp vrid 2 virtual-ip 20.1.1.100

# Set the priority of Device D to 200 for it to become the master in VRRP group 2.

[DeviceD-Vlan-interface20] vrrp vrid 2 priority 200

# Configure Device D to operate in preemptive mode in VRRP group 2. Set the preemption delay to 500 centiseconds to avoid frequent status switchover.

[DeviceD-Vlan-interface20] vrrp vrid 2 preempt-mode delay 500

[DeviceD-Vlan-interface20] quit

# Create track entry 2 to monitor the upstream link status of Ten-GigabitEthernet 1/0/3.

[DeviceD] track 2 interface ten-gigabitethernet 1/0/3

# Configure Device D in VRRP group 2 to monitor track entry 2, and decrease its priority by 150 when the track entry transits to Negative.

[DeviceD] interface vlan-interface 20

[DeviceD-Vlan-interface20] vrrp vrid 2 track 2 priority reduced 150

[DeviceD-Vlan-interface20] quit

# Configure OSPF.

[DeviceD] ospf

[DeviceD-ospf-1] area 0

[DeviceD-ospf-1-area-0.0.0.0] network 10.1.1.0 0.0.0.255

[DeviceD-ospf-1-area-0.0.0.0] network 20.1.1.0 0.0.0.255

[DeviceD-ospf-1-area-0.0.0.0] network 200.1.1.0 0.0.0.255

[DeviceD-ospf-1-area-0.0.0.0] quit

[DeviceD-ospf-1] quit

Configuring Device E

# Create VLAN 100 and assign Ten-GigabitEthernet 1/0/1 to the VLAN.

<DeviceE> system-view

[DeviceE] vlan 100

[DeviceE-vlan100] port ten-gigabitethernet 1/0/1

[DeviceE-vlan100] quit

# Create VLAN-interface 100 and assign it an IP address.

[DeviceE] interface vlan-interface 100

[DeviceE-vlan-interface100] ip address 100.1.1.2 24

[DeviceE-vlan-interface100] quit

# Create VLAN 200 and assign Ten-GigabitEthernet 1/0/2 to the VLAN.

[DeviceE] vlan 200

[DeviceE-vlan200] port ten-gigabitethernet 1/0/2

[DeviceE-vlan200] quit

# Create VLAN-interface 200 and assign it an IP address.

[DeviceE] interface vlan-interface 200

[DeviceE-vlan-interface200] ip address 200.1.1.2 24

[DeviceE-vlan-interface200] quit

# Create VLAN 30 and assign Ten-GigabitEthernet 1/0/3 to the VLAN.

[DeviceE] vlan 30

[DeviceE-vlan30] port ten-gigabitethernet 1/0/3

[DeviceE-vlan30] quit

# Create VLAN-interface 30 and assign it an IP address.

[DeviceE] interface vlan-interface 30

[DeviceE-vlan-interface30] ip address 30.1.1.1 24

[DeviceE-vlan-interface30] quit

# Configure OSPF.

[DeviceD] ospf

[DeviceD-ospf-1] area 0

[DeviceD-ospf-1-area-0.0.0.0] network 100.1.1.0 0.0.0.255

[DeviceD-ospf-1-area-0.0.0.0] network 200.1.1.0 0.0.0.255

[DeviceD-ospf-1-area-0.0.0.0] network 30.1.1.0 0.0.0.255

[DeviceD-ospf-1-area-0.0.0.0] quit

[DeviceD-ospf-1] quit

Configuring Device F

# Create VLAN 10 and VLAN 20.

[DeviceF] vlan 10

[DeviceF-vlan10] quit

[DeviceF] vlan 20

[DeviceF-vlan20] quit

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 4.

[DeviceF] interface bridge-aggregation 4

[DeviceF-Bridge-Aggregation4] link-aggregation mode dynamic

[DeviceF-Bridge-Aggregation4] quit

# Assign Ten-GigabitEthernet 1/0/1 through Ten-GigabitEthernet 1/0/4 to aggregation group 4.

[DeviceF] interface range ten-gigabitethernet 1/0/1 to ten-gigabitethernet 1/0/4

[DeviceF-if-range] port link-aggregation group 4

[DeviceF-if-range] quit

# Set the link type of Bridge-Aggregation 4 to trunk and assign it to VLAN 10 and VLAN 20.

[DeviceF] interface bridge-aggregation 4

[DeviceF-Bridge-Aggregation4] port link-type trunk

Configuring Ten-GigabitEthernet1/0/1 done.

Configuring Ten-GigabitEthernet1/0/2 done.

Configuring Ten-GigabitEthernet1/0/3 done.

Configuring Ten-GigabitEthernet1/0/4 done.

[DeviceF-Bridge-Aggregation4] port trunk permit vlan 10 20

Configuring Ten-GigabitEthernet1/0/1 done.

Configuring Ten-GigabitEthernet1/0/2 done.

Configuring Ten-GigabitEthernet1/0/3 done.

Configuring Ten-GigabitEthernet1/0/4 done.

[DeviceF-Bridge-Aggregation4] quit

Verifying the configuration

# Verify that Device A and Device B have formed a DR system.

[DeviceA] display drni summary

Global consistency check           : SUCCESS

Inconsistent type 1 global settings: -

 

IPP             IPP ID        State

BAGG3           1             UP

 

DR interface    DR group ID   State    Check result   Type 1 inconsistency

BAGG4           4             UP       SUCCESS        -

[DeviceA] display drni verbose

Flags: A -- Home_Gateway, B -- Neighbor_Gateway, C -- Other_Gateway,

       D -- IPP_Activity, E -- DRCP_Timeout, F -- Gateway_Sync,

       G -- Port_Sync, H -- Expired

 

IPP/IPP ID: BAGG3/1

State: UP

Local state/Peer state: ABDFG/ABDFG

Local Selected ports Index: 2, 5

Peer Selected ports Index: 2, 5

 

DR interface/DR group ID: BAGG4/4

State: UP

Local state/Peer state: ABDFG/ABDFG

Local Selected ports Index: 16385, 16388

Peer Selected ports Index: 32769, 32772

# Verify that all member ports of aggregation group 4 are in Selected state on Device F, which indicates a successful link aggregation between the DR system and Device F.

[DeviceF] display link-aggregation verbose

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port, M -- Management port, R -- Reference port

Flags:  A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

        D -- Synchronization, E -- Collecting, F -- Distributing,

        G -- Defaulted, H -- Expired

 

Aggregate Interface: Bridge-Aggregation4

Aggregation Mode: Dynamic

Loadsharing Type: Shar

Management VLANs: None

System ID: 0x8000, 1eba-3c46-0300

Local:

  Port                Status   Priority Index    Oper-Key               Flag

  XGE1/0/1            S        32768    1        1                      {ACDEF}

  XGE1/0/2            S        32768    2        1                      {ACDEF}

  XGE1/0/3            S        32768    3        1                      {ACDEF}

  XGE1/0/4            S        32768    4        1                      {ACDEF}

Remote:

  Actor               Priority Index    Oper-Key SystemID               Flag

  XGE1/0/1(R)         32768    16385    40004    0x7b  , 0001-0001-0001 {ACDEF}

  XGE1/0/2            32768    16388    40004    0x7b  , 0001-0001-0001 {ACDEF}

  XGE1/0/3            32768    32769    40004    0x7b  , 0001-0001-0001 {ACDEF}

  XGE1/0/4            32768    32772    40004    0x7b  , 0001-0001-0001 {ACDEF}

# Verify that Device C is the master in VRRP group 1 and Device D is the master in VRRP group 2.

[DeviceC] display vrrp

IPv4 Virtual Router Information:

 Running mode : Standard

 Total number of virtual routers : 2

 Interface          VRID  State        Running Adver   Auth     Virtual

                                       Pri     Timer   Type        IP

 ---------------------------------------------------------------------

 Vlan10             1     Master       200     100     None     10.1.1.100

 Vlan20             2     Backup       100     100     None     20.1.1.100

[DeviceD] display vrrp

IPv4 Virtual Router Information:

 Running mode : Standard

 Total number of virtual routers : 2

 Interface          VRID  State        Running Adver   Auth     Virtual

                                       Pri     Timer   Type        IP

 ---------------------------------------------------------------------

 Vlan10             1     Backup       100     100     None     10.1.1.100

 Vlan20             2     Master       200     100     None     20.1.1.100

# Verify that Device E has established OSPF neighbor relationships with Device C and Device D.

[DeviceE] display ospf peer

 

         OSPF Process 1 with Router ID 200.1.1.2

               Neighbor Brief Information

 

 Area: 0.0.0.0

 Router ID       Address         Pri Dead-Time  State             Interface

 100.1.1.1       100.1.1.1       1   35         Full/BDR          Vlan100

 200.1.1.1       200.1.1.1       1   33         Full/BDR          Vlan200

# Verify that the host in Area A can ping VLAN-interface 30 (30.1.1.1) on Device E.

C:\Documents and Settings\Administrator>ping 30.1.1.1

 

Pinging 30.1.1.1 with 32 bytes of data:

 

Reply from 30.1.1.1: bytes=32 time=1ms TTL=126

Reply from 30.1.1.1: bytes=32 time=1ms TTL=126

Reply from 30.1.1.1: bytes=32 time=1ms TTL=126

Reply from 30.1.1.1: bytes=32 time=1ms TTL=126

 

Ping statistics for 30.1.1.1:

    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

Approximate round trip times in milli-seconds:

    Minimum = 1ms, Maximum = 1ms, Average = 1ms

Configuration files

·          Device A:

#

vlan 10

#

vlan 20

#

interface Bridge-Aggregation1

 port link-type trunk

 port trunk permit vlan 1 10 20

 link-aggregation mode dynamic

#

interface Bridge-Aggregation3

 port link-type trunk

 port trunk permit vlan 1 10 20

 link-aggregation mode dynamic

 port drni intra-portal-port 1

#

interface Bridge-Aggregation4

 port link-type trunk

 port trunk permit vlan 1 10 20

 link-aggregation mode dynamic

 port drni group 4

#

interface Ten-GigabitEthernet1/0/5

 port link-mode route

 ip address 1.1.1.1 255.255.255.0

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 4

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 4

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 3

#

interface Ten-GigabitEthernet1/0/4

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 3

#

interface Ten-GigabitEthernet1/0/6

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 1

#

interface Ten-GigabitEthernet1/0/7

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 1

#

 drni system-mac 0001-0001-0001

 drni system-number 1

 drni system-priority 123

 drni keepalive ip destination 1.1.1.2 source 1.1.1.1

#

 mad exclude interface Ten-GigabitEthernet1/0/5

#

·          Device B:

#

vlan 10

#

vlan 20

#

interface Bridge-Aggregation2

 port link-type trunk

 port trunk permit vlan 1 10 20

 link-aggregation mode dynamic

#

interface Bridge-Aggregation3

 port link-type trunk

 port trunk permit vlan 1 10 20

 link-aggregation mode dynamic

 port drni intra-portal-port 1

#

interface Bridge-Aggregation4

 port link-type trunk

 port trunk permit vlan 1 10 20

 link-aggregation mode dynamic

 port drni group 4

#

interface Ten-GigabitEthernet1/0/5

 port link-mode route

 ip address 1.1.1.2 255.255.255.0

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 4

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 4

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 3

#

interface Ten-GigabitEthernet1/0/4

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 3

#

interface Ten-GigabitEthernet1/0/6

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 2

#

interface Ten-GigabitEthernet1/0/7

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 2

#

 drni system-mac 0001-0001-0001

 drni system-number 2

 drni system-priority 123

 drni keepalive ip destination 1.1.1.1 source 1.1.1.2

#

 mad exclude interface Ten-GigabitEthernet1/0/5

#

·          Device C:

#

ospf 1

 area 0.0.0.0

  network 10.1.1.0 0.0.0.255

  network 20.1.1.0 0.0.0.255

  network 100.1.1.0 0.0.0.255

#

vlan 10

#

vlan 20

#

vlan 100

#

interface Bridge-Aggregation1

 port link-type trunk

 port trunk permit vlan 1 10 20

 link-aggregation mode dynamic

#

interface Vlan-interface10

 ip address 10.1.1.1 255.255.255.0

 vrrp vrid 1 virtual-ip 10.1.1.100

 vrrp vrid 1 priority 200

 vrrp vrid 1 preempt-mode delay 500

 vrrp vrid 1 track 1 priority reduced 150

#

interface Vlan-interface20

 ip address 20.1.1.1 255.255.255.0

 vrrp vrid 2 virtual-ip 20.1.1.100

#

interface Vlan-interface100

 ip address 100.1.1.1 255.255.255.0

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 1

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 1

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port access vlan 100

#

 track 1 interface Ten-GigabitEthernet1/0/3

#

·          Device D:

#

ospf 1

 area 0.0.0.0

  network 10.1.1.0 0.0.0.255

  network 20.1.1.0 0.0.0.255

  network 200.1.1.0 0.0.0.255

#

vlan 10

#

vlan 20

#

vlan 200

#

interface Bridge-Aggregation2

 port link-type trunk

 port trunk permit vlan 1 10 20

 link-aggregation mode dynamic

#

interface Vlan-interface10

 ip address 10.1.1.2 255.255.255.0

 vrrp vrid 1 virtual-ip 10.1.1.100

#

interface Vlan-interface20

 ip address 20.1.1.2 255.255.255.0

 vrrp vrid 2 virtual-ip 20.1.1.100

 vrrp vrid 2 priority 200

 vrrp vrid 2 preempt-mode delay 500

 vrrp vrid 2 track 2 priority reduced 150

#

interface Vlan-interface200

 ip address 200.1.1.1 255.255.255.0

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 2

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 2

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port access vlan 200

#

 track 2 interface Ten-GigabitEthernet1/0/3

#

·          Device E:

#

ospf 1

 area 0.0.0.0

  network 3.3.3.3 0.0.0.0

  network 30.1.1.0 0.0.0.255

  network 100.1.1.0 0.0.0.255

  network 200.1.1.0 0.0.0.255

#

vlan 30

#

vlan 100

#

vlan 200

#

interface Vlan-interface30

 ip address 30.1.1.1 255.255.255.0

#

interface Vlan-interface100

 ip address 100.1.1.2 255.255.255.0

#

interface Vlan-interface200

 ip address 200.1.1.2 255.255.255.0

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port access vlan 100

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port access vlan 200

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port access vlan 30

#

·          Device F:

#

vlan 10

#

vlan 20

#

interface Bridge-Aggregation4

 port link-type trunk

 port trunk permit vlan 1 10 20

 link-aggregation mode dynamic

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 4

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 4

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 4

#

interface Ten-GigabitEthernet1/0/4

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 10 20

 port link-aggregation group 4

#

Example: Configuring DRNI at the distribution Layer

Network configuration

As shown in Figure 2:

·          Configure Device A and Device B as a DR system to establish one multichassis aggregate link with Device C and Device D.

·          Set up a keepalive link between Ten-GigabitEthernet 1/0/5 of Device A and Ten-GigabitEthernet 1/0/5 of Device B, and exclude the interfaces from the shutdown action by DRNI MAD.

·          Configure two VRRP groups on Device A and Device B to provide gateway services for VLAN 100 and VLAN 101.

¡  Configure VRRP group 1 to provide gateway services for hosts in VLAN 100 (Area A). Add Device A and Device B to the group as the master and backup devices, respectively.

¡  Configure VRRP group 2 to provide gateway services for hosts in VLAN 101 (Area B). Add Device B and Device A to the group as the master and backup devices, respectively.

·          Configure OSPF on Device A, Device B, and Device E for the hosts to communicate with external networks at Layer 3.

Figure 2 Network diagram

 

Device	Interface	IP address	Device	Interface	IP address
Device A	XGE 1/0/5	1.1.1.1/24	Device B	XGE 1/0/5	1.1.1.2/24
	VLAN-interface 100	100.1.1.1/24		VLAN-interface 100	100.1.1.2/24
	VLAN-interface 101	101.1.1.1/24		VLAN-interface 101	101.1.1.2/24
	VLAN-interface 10	10.1.1.1/24		VLAN-interface 20	20.1.1.1/24
	Virtual IP 1	100.1.1.100/24		Virtual IP 1	100.1.1.100/24
	Virtual IP 2	101.1.1.100/24		Virtual IP 2	101.1.1.100/24
Device E	VLAN-interface 10	10.1.1.2/24
	VLAN-interface 20	20.1.1.2/24
	VLAN-interface 30	30.1.1.1/24

 

Analysis

For the secondary DR device to monitor the state of the primary device, establish a Layer 3 keepalive link between the DR member devices.

For Device A to be the master in VRRP group 1, assign it a higher priority than Device B. For Device B to be the master in VRRP group 2, assign it a higher priority than Device A.

Software versions used

This configuration example was created and verified on S6890-CMW710-R2712.

Restrictions and guidelines

Interface restrictions and guidelines

By default, interfaces on S6890 switches are disabled (in ADM or Administratively Down state). To have an interface operate, you must use the undo shutdown command to enable that interface.

DRNI restrictions and guidelines

For the DR member devices to be identified as one DR system, you must configure the same DR system MAC address and DR system priority on them. You must assign different DR system numbers to the DR member devices.

To balance traffic between two VRRP gateway devices, you can assign them to two VRRP groups with different priorities. In this example, Device A is assigned a higher priority than Device B in VRRP group 1 so Device A can become the master in this group. Device B is assigned a higher priority than Device A in VRRP group 2 so Device B can become the master in this group.

A DR member device can have only one IPP.

For correct keepalive detection, you must exclude the interfaces used for keepalive detection from the shutdown action by DRNI MAD.

VRRP restrictions and guidelines

You cannot specify the virtual IP address as any of the following IP addresses:

·          All-zero address (0.0.0.0).

·          Broadcast address (255.255.255.255).

·          Loopback address.

·          IP address of other than Class A, Class B, and Class C.

·          Invalid IP address (for example, 0.0.0.1).

The virtual IP address of an IPv4 VRRP group must be on the same subnet as the downlink interface IP addresses of the VRRP group members to ensure successful traffic forwarding.

Procedures

Configuring Device A

# Configure DR system settings.

<DeviceA> system-view

[DeviceA] drni system-mac 1-1-1

Changing the system MAC might flap the intra-portal link and cause DR system setup failure. Continue? [Y/N]:y

[DeviceA] drni system-number 1

Changing the system number might flap the intra-portal link and cause DR system setup failure. Continue? [Y/N]:y

[DeviceA] drni system-priority 123

Changing the system priority might flap the intra-portal link and cause DR system setup failure. Continue? [Y/N]:y

# Configure DR keepalive packet parameters.

[DeviceA] drni keepalive ip destination 1.1.1.2 source 1.1.1.1

# Configure Ten-GigabitEthernet 1/0/5 as a routed (Layer 3) interface and assign the interface an IP address. The IP address will be used as the source IP address of keepalive packets.

[DeviceA] interface ten-gigabitethernet 1/0/5

[DeviceA-Ten-GigabitEthernet1/0/5] port link-mode route

[DeviceA-Ten-GigabitEthernet1/0/5] ip address 1.1.1.1 24

[DeviceA-Ten-GigabitEthernet1/0/5] quit

# Exclude the interface used for DR keepalive detection (Ten-GigabitEthernet 1/0/5) from the shutdown action by DRNI MAD.

[DeviceA] mad exclude interface ten-gigabitethernet 1/0/5

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 125 and specify it as the IPP.

[DeviceA] interface bridge-aggregation 125

[DeviceA-Bridge-Aggregation125] link-aggregation mode dynamic

[DeviceA-Bridge-Aggregation125] port drni intra-portal-port 1

[DeviceA-Bridge-Aggregation125] quit

# Assign Ten-GigabitEthernet 1/0/3 and Ten-GigabitEthernet 1/0/4 to aggregation group 125.

[DeviceA] interface ten-gigabitethernet 1/0/3

[DeviceA-Ten-GigabitEthernet1/0/3] port link-aggregation group 125

[DeviceA-Ten-GigabitEthernet1/0/3] quit

[DeviceA] interface ten-gigabitethernet 1/0/4

[DeviceA-Ten-GigabitEthernet1/0/4] port link-aggregation group 125

[DeviceA-Ten-GigabitEthernet1/0/4] quit

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 100 and assign it to DR group 1.

[DeviceA] interface bridge-aggregation 100

[DeviceA-Bridge-Aggregation100] link-aggregation mode dynamic

[DeviceA-Bridge-Aggregation100] port drni group 1

[DeviceA-Bridge-Aggregation100] quit

# Assign Ten-GigabitEthernet 1/0/1 to aggregation group 100.

[DeviceA] interface ten-gigabitethernet 1/0/1

[DeviceA-Ten-GigabitEthernet1/0/1] port link-aggregation group 100

[DeviceA-Ten-GigabitEthernet1/0/1] quit

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 101 and assign it to DR group 2.

[DeviceA] interface bridge-aggregation 101

[DeviceA-Bridge-Aggregation101] link-aggregation mode dynamic

[DeviceA-Bridge-Aggregation101] port drni group 2

[DeviceA-Bridge-Aggregation101] quit

# Assign Ten-GigabitEthernet 1/0/2 to aggregation group 101.

[DeviceA] interface ten-gigabitethernet 1/0/2

[DeviceA-Ten-GigabitEthernet1/0/2] port link-aggregation group 101

[DeviceA-Ten-GigabitEthernet1/0/2] quit

# Create VLAN 10, VLAN 100, and VLAN 101.

[DeviceA] vlan 10

[DeviceA-vlan10] quit

[DeviceA] vlan 100

[DeviceA-vlan100] quit

[DeviceA] vlan 101

[DeviceA-vlan101] quit

# Assign Ten-GigabitEthernet 1/0/6 to VLAN 10.

[DeviceA] vlan 10

[DeviceA-vlan10] port ten-gigabitethernet 1/0/6

[DeviceA-vlan10] quit

# Set the link type of Bridge-Aggregation 100 to trunk and assign it to VLAN 100.

[DeviceA] interface bridge-aggregation 100

[DeviceA-Bridge-Aggregation100] port link-type trunk

Configuring Ten-GigabitEthernet1/0/1 done.

[DeviceA-Bridge-Aggregation100] port trunk permit vlan 100

Configuring Ten-GigabitEthernet1/0/1 done.

[DeviceA-Bridge-Aggregation100] quit

# Set the link type of Bridge-Aggregation 101 to trunk and assign it to VLAN 101.

[DeviceA] interface bridge-aggregation 101

[DeviceA-Bridge-Aggregation101] port link-type trunk

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceA-Bridge-Aggregation101] port trunk permit vlan 101

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceA-Bridge-Aggregation101] quit

# Set the link type of Bridge-Aggregation 125 to trunk and assign it to VLAN 100 and VLAN 101.

[DeviceA] interface bridge-aggregation 125

[DeviceA-Bridge-Aggregation125] port link-type trunk

Configuring Ten-GigabitEthernet1/0/3 done.

Configuring Ten-GigabitEthernet1/0/4 done.

[DeviceA-Bridge-Aggregation125] port trunk permit vlan 100 101

Configuring Ten-GigabitEthernet1/0/3 done.

Configuring Ten-GigabitEthernet1/0/4 done.

[DeviceA-Bridge-Aggregation125] quit

# Create VLAN-interface 10, VLAN-interface 100, and VLAN-interface 101 and assign an IP address to each of them.

[DeviceA] interface vlan-interface 10

[DeviceA-vlan-interface10] ip address 10.1.1.1 24

[DeviceA-vlan-interface10] quit

[DeviceA] interface vlan-interface 100

[DeviceA-vlan-interface100] ip address 100.1.1.1 24

[DeviceA-vlan-interface100] quit

[DeviceA] interface vlan-interface 101

[DeviceA-vlan-interface101] ip address 101.1.1.1 24

[DeviceA-vlan-interface101] quit

# Configure OSPF.

[DeviceA] ospf

[DeviceA-ospf-1] area 0

[DeviceA-ospf-1-area-0.0.0.0] network 10.1.1.0 0.0.0.255

[DeviceA-ospf-1-area-0.0.0.0] network 100.1.1.0 0.0.0.255

[DeviceA-ospf-1-area-0.0.0.0] network 101.1.1.0 0.0.0.255

[DeviceA-ospf-1-area-0.0.0.0] quit

[DeviceA-ospf-1] quit

# Create VRRP group 1 on VLAN-interface 100 and set its virtual IP address to 100.1.1.100.

[DeviceA] interface vlan-interface 100

[DeviceA-Vlan-interface100] vrrp vrid 1 virtual-ip 100.1.1.100

# Set the priority of Device A to 200 for it to become the master in VRRP group 1.

[DeviceA-Vlan-interface100] vrrp vrid 1 priority 200

[DeviceA-Vlan-interface100] quit

# Create VRRP group 2 on VLAN-interface 101 and set its virtual IP address to 101.1.1.100.

[DeviceA] interface vlan-interface 101

[DeviceA-Vlan-interface101] vrrp vrid 2 virtual-ip 101.1.1.100

[DeviceA-Vlan-interface101] quit

# Configure Device A to operate in preemptive mode in VRRP group 1. Set the preemption delay to 500 centiseconds to avoid frequent status switchover.

[DeviceA] interface vlan-interface 100

[DeviceA-Vlan-interface100] vrrp vrid 1 preempt-mode delay 500

[DeviceA-Vlan-interface100] quit

# Create track entry 1 to monitor the upstream link status of Ten-GigabitEthernet 1/0/6.

[DeviceA] track 1 interface ten-gigabitethernet 1/0/6

# Configure Device A in VRRP group 1 to monitor track entry 1, and decrease its priority by 150 when the track entry transits to Negative.

[DeviceA] interface vlan-interface 100

[DeviceA-Vlan-interface100] vrrp vrid 1 track 1 priority reduced 150

[DeviceA-Vlan-interface100] quit

Configuring Device B

# Configure DR system settings.

<DeviceB> system-view

[DeviceB] drni system-mac 1-1-1

Changing the system MAC might flap the intra-portal link and cause DR system setup failure. Continue? [Y/N]:y

[DeviceB] drni system-number 2

Changing the system number might flap the intra-portal link and cause DR system setup failure. Continue? [Y/N]:y

[DeviceB] drni system-priority 123

Changing the system priority might flap the intra-portal link and cause DR system setup failure. Continue? [Y/N]:y

# Configure DR keepalive packet parameters.

[DeviceB] drni keepalive ip destination 1.1.1.1 source 1.1.1.2

# Configure Ten-GigabitEthernet 1/0/5 as a routed (Layer 3) interface and assign the interface an IP address. The IP address will be used as the source IP address of keepalive packets.

[DeviceB] interface ten-gigabitethernet 1/0/5

[DeviceB-Ten-GigabitEthernet1/0/5] port link-mode route

[DeviceB-Ten-GigabitEthernet1/0/5] ip address 1.1.1.2 24

[DeviceB-Ten-GigabitEthernet1/0/5] quit

# Exclude the interface used for DR keepalive detection (Ten-GigabitEthernet 1/0/5) from the shutdown action by DRNI MAD.

[DeviceB] mad exclude interface ten-gigabitethernet 1/0/5

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 125 and specify it as the IPP.

[DeviceB] interface bridge-aggregation 125

[DeviceB-Bridge-Aggregation125] link-aggregation mode dynamic

[DeviceB-Bridge-Aggregation125] port drni intra-portal-port 1

[DeviceB-Bridge-Aggregation125] quit

# Assign Ten-GigabitEthernet 1/0/3 and Ten-GigabitEthernet 1/0/4 to aggregation group 125.

[DeviceB] interface ten-gigabitethernet 1/0/3

[DeviceB-Ten-GigabitEthernet1/0/3] port link-aggregation group 125

[DeviceB-Ten-GigabitEthernet1/0/3] quit

[DeviceB] interface ten-gigabitethernet 1/0/4

[DeviceB-Ten-GigabitEthernet1/0/4] port link-aggregation group 125

[DeviceB-Ten-GigabitEthernet1/0/4] quit

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 100 and assign it to DR group 1.

[DeviceB] interface bridge-aggregation 100

[DeviceB-Bridge-Aggregation100] link-aggregation mode dynamic

[DeviceB-Bridge-Aggregation100] port drni group 1

[DeviceB-Bridge-Aggregation100] quit

# Assign Ten-GigabitEthernet 1/0/2 to aggregation group 100.

[DeviceB] interface ten-gigabitethernet 1/0/2

[DeviceB-Ten-GigabitEthernet1/0/2] port link-aggregation group 100

[DeviceB-Ten-GigabitEthernet1/0/2] quit

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 101 and assign it to DR group 2.

[DeviceB] interface bridge-aggregation 101

[DeviceB-Bridge-Aggregation101] link-aggregation mode dynamic

[DeviceB-Bridge-Aggregation101] port drni group 2

[DeviceB-Bridge-Aggregation101] quit

# Assign Ten-GigabitEthernet 1/0/1 to aggregation group 101.

[DeviceB] interface ten-gigabitethernet 1/0/1

[DeviceB-Ten-GigabitEthernet1/0/1] port link-aggregation group 101

[DeviceB-Ten-GigabitEthernet1/0/1] quit

# Create VLAN 20, VLAN 100, and VLAN 101.

[DeviceB] vlan 20

[DeviceB-vlan20] quit

[DeviceB] vlan 100

[DeviceB-vlan100] quit

[DeviceB] vlan 101

[DeviceB-vlan101] quit

# Assign Ten-GigabitEthernet 1/0/6 to VLAN 20.

[DeviceB] vlan 20

[DeviceB-vlan20] port ten-gigabitethernet 1/0/6

[DeviceB-vlan20] quit

# Set the link type of Bridge-Aggregation 100 to trunk and assign it to VLAN 100.

[DeviceB] interface bridge-aggregation 100

[DeviceB-Bridge-Aggregation100] port link-type trunk

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceB-Bridge-Aggregation100] port trunk permit vlan 100

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceB-Bridge-Aggregation100] quit

# Set the link type of Bridge-Aggregation 101 to trunk and assign it to VLAN 101.

[DeviceB] interface bridge-aggregation 101

[DeviceB-Bridge-Aggregation101] port link-type trunk

Configuring Ten-GigabitEthernet1/0/1 done.

[DeviceB-Bridge-Aggregation101] port trunk permit vlan 101

Configuring Ten-GigabitEthernet1/0/1 done.

[DeviceB-Bridge-Aggregation101] quit

# Set the link type of Bridge-Aggregation 125 to trunk and assign it to VLAN 100 and VLAN 101.

[DeviceB] interface bridge-aggregation 125

[DeviceB-Bridge-Aggregation125] port link-type trunk

Configuring Ten-GigabitEthernet1/0/3 done.

Configuring Ten-GigabitEthernet1/0/4 done.

[DeviceB-Bridge-Aggregation125] port trunk permit vlan 100 101

Configuring Ten-GigabitEthernet1/0/3 done.

Configuring Ten-GigabitEthernet1/0/4 done.

[DeviceB-Bridge-Aggregation125] quit

# Create VLAN-interface 20, VLAN-interface 100, and VLAN-interface 101 and assign an IP address to each of them.

[DeviceB] interface vlan-interface 20

[DeviceB-vlan-interface20] ip address 20.1.1.1 24

[DeviceB-vlan-interface20] quit

[DeviceB] interface vlan-interface 100

[DeviceB-vlan-interface100] ip address 100.1.1.2 24

[DeviceB-vlan-interface100] quit

[DeviceB] interface vlan-interface 101

[DeviceB-vlan-interface101] ip address 101.1.1.2 24

[DeviceB-vlan-interface101] quit

# Configure OSPF.

[DeviceB] ospf

[DeviceB-ospf-1] area 0

[DeviceB-ospf-1-area-0.0.0.0] network 20.1.1.0 0.0.0.255

[DeviceB-ospf-1-area-0.0.0.0] network 100.1.1.0 0.0.0.255

[DeviceB-ospf-1-area-0.0.0.0] network 101.1.1.0 0.0.0.255

[DeviceB-ospf-1-area-0.0.0.0] quit

[DeviceB-ospf-1] quit

# Create VRRP group 1 on VLAN-interface 100 and set its virtual IP address to 100.1.1.100.

[DeviceB] interface vlan-interface 100

[DeviceB-Vlan-interface100] vrrp vrid 1 virtual-ip 100.1.1.100

[DeviceB-Vlan-interface100] quit

# Create VRRP group 2 on VLAN-interface 101 and set its virtual IP address to 101.1.1.100.

[DeviceB] interface vlan-interface 101

[DeviceB-Vlan-interface101] vrrp vrid 2 virtual-ip 101.1.1.100

# Set the priority of Device B to 200 for it to become the master in VRRP group 2.

[DeviceB-Vlan-interface101] vrrp vrid 2 priority 200

# Configure Device B to operate in preemptive mode in VRRP group 2. Set the preemption delay to 500 centiseconds to avoid frequent status switchover.

[DeviceB-Vlan-interface101] vrrp vrid 2 preempt-mode delay 500

[DeviceB-Vlan-interface101] quit

# Create track entry 2 to monitor the upstream link status of Ten-GigabitEthernet 1/0/6.

[DeviceB] track 2 interface ten-gigabitethernet 1/0/6

# Configure Device B in VRRP group 2 to monitor track entry 2, and decrease its priority by 150 when the track entry transits to Negative.

[DeviceB] interface vlan-interface 101

[DeviceB-Vlan-interface101] vrrp vrid 2 track 2 priority reduced 150

[DeviceB-Vlan-interface101] quit

Configuring Device C

# Create VLAN 100.

[DeviceC] vlan 100

[DeviceC-vlan100] quit

# Assign Ten-GigabitEthernet 1/0/3 to VLAN 100.

[DeviceC] interface ten-gigabitethernet 1/0/3

[DeviceC-Ten-GigabitEthernet1/0/3] port access vlan 100

[DeviceC-Ten-GigabitEthernet1/0/3] quit

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 100.

<DeviceC> system-view

[DeviceC] interface bridge-aggregation 100

[DeviceC-Bridge-Aggregation100] link-aggregation mode dynamic

[DeviceC-Bridge-Aggregation100] quit

# Assign Ten-GigabitEthernet 1/0/1 and Ten-GigabitEthernet 1/0/2 to aggregation group 100.

[DeviceC] interface range ten-gigabitethernet 1/0/1 to ten-gigabitethernet 1/0/2

[DeviceC-if-range] port link-aggregation group 100

[DeviceC-if-range] quit

# Set the link type of Bridge-Aggregation 100 to trunk and assign it to VLAN 100.

[DeviceC] interface bridge-aggregation 100

[DeviceC-Bridge-Aggregation100] port link-type trunk

Configuring Ten-GigabitEthernet1/0/1 done.

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceC-Bridge-Aggregation100] port trunk permit vlan 100

Configuring Ten-GigabitEthernet1/0/1 done.

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceC-Bridge-Aggregation100] quit

Configuring Device D

# Create VLAN 101.

[DeviceD] vlan 101

[DeviceD-vlan101] quit

# Assign Ten-GigabitEthernet 1/0/3 to VLAN 101.

[DeviceD] interface ten-gigabitethernet 1/0/3

[DeviceD-Ten-GigabitEthernet1/0/3] port access vlan 101

[DeviceD-Ten-GigabitEthernet1/0/3] quit

# Create Layer 2 dynamic aggregate interface Bridge-Aggregation 101.

<DeviceD> system-view

[DeviceD] interface bridge-aggregation 101

[DeviceD-Bridge-Aggregation101] link-aggregation mode dynamic

[DeviceD-Bridge-Aggregation101] quit

# Assign Ten-GigabitEthernet 1/0/1 and Ten-GigabitEthernet 1/0/2 to aggregation group 101.

[DeviceD] interface range ten-gigabitethernet 1/0/1 to ten-gigabitethernet 1/0/2

[DeviceD-if-range] port link-aggregation group 101

[DeviceD-if-range] quit

# Set the link type of Bridge-Aggregation 101 to trunk and assign it to VLAN 101.

[DeviceD] interface bridge-aggregation 101

[DeviceD-Bridge-Aggregation101] port link-type trunk

Configuring Ten-GigabitEthernet1/0/1 done.

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceD-Bridge-Aggregation101] port trunk permit vlan 101

Configuring Ten-GigabitEthernet1/0/1 done.

Configuring Ten-GigabitEthernet1/0/2 done.

[DeviceD-Bridge-Aggregation101] quit

Configuring Device E

# Create VLAN 10 and assign Ten-GigabitEthernet 1/0/1 to the VLAN.

<DeviceE> system-view

[DeviceE] vlan 10

[DeviceE-vlan10] port ten-gigabitethernet 1/0/1

[DeviceE-vlan10] quit

# Create VLAN-interface 10 and assign it an IP address.

[DeviceE] interface vlan-interface 10

[DeviceE-vlan-interface10] ip address 10.1.1.2 24

[DeviceE-vlan-interface10] quit

# Create VLAN 20 and assign Ten-GigabitEthernet 1/0/2 to the VLAN.

[DeviceE] vlan 20

[DeviceE-vlan20] port ten-gigabitethernet 1/0/2

[DeviceE-vlan20] quit

# Create VLAN-interface 20 and assign it an IP address.

[DeviceE] interface vlan-interface 20

[DeviceE-vlan-interface20] ip address 20.1.1.2 24

[DeviceE-vlan-interface20] quit

# Create VLAN 30 and assign Ten-GigabitEthernet 1/0/3 to the VLAN.

[DeviceE] vlan 30

[DeviceE-vlan30] port ten-gigabitethernet 1/0/3

[DeviceE-vlan30] quit

# Create VLAN-interface 30 and assign it an IP address.

[DeviceE] interface vlan-interface 30

[DeviceE-vlan-interface30] ip address 30.1.1.1 24

[DeviceE-vlan-interface30] quit

# Configure OSPF.

[DeviceE] ospf

[DeviceE-ospf-1] area 0

[DeviceE-ospf-1-area-0.0.0.0] network 10.1.1.0 0.0.0.255

[DeviceE-ospf-1-area-0.0.0.0] network 20.1.1.0 0.0.0.255

[DeviceE-ospf-1-area-0.0.0.0] network 30.1.1.0 0.0.0.255

[DeviceE-ospf-1-area-0.0.0.0] quit

[DeviceE-ospf-1] quit

Verifying the configuration

# Verify that Device A and Device B have formed a DR system.

[DeviceA] display drni summary

Global consistency check           : SUCCESS

Inconsistent type 1 global settings: -

 

IPP             IPP ID        State

BAGG125         1             UP

 

DR interface    DR group ID   State    Check result   Type 1 inconsistency

BAGG100         1             UP       SUCCESS        -

BAGG101         2             UP       SUCCESS        -

[DeviceA] display drni verbose

Flags: A -- Home_Gateway, B -- Neighbor_Gateway, C -- Other_Gateway,

       D -- IPP_Activity, E -- DRCP_Timeout, F -- Gateway_Sync,

       G -- Port_Sync, H -- Expired

 

IPP/IPP ID: BAGG125/1

State: UP

Local state/Peer state: ABDFG/ABDFG

Local Selected ports Index: 1, 4

Peer Selected ports Index: 1, 4

 

DR interface/DR group ID: BAGG100/1

State: UP

Local state/Peer state: ABDFG/ABDFG

Local Selected ports Index: 16386

Peer Selected ports Index: 32771

 

DR interface/DR group ID: BAGG101/2

State: UP

Local state/Peer state: ABDFG/ABDFG

Local Selected ports Index: 16387

Peer Selected ports Index: 32772

# Verify that all member ports of aggregation group 100 are in Selected state on Device C, which indicates a successful link aggregation between the DR system and Device C.

[DeviceC] display link-aggregation verbose

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port, M -- Management port, R -- Reference port

Flags:  A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

        D -- Synchronization, E -- Collecting, F -- Distributing,

        G -- Defaulted, H -- Expired

 

Aggregate Interface: Bridge-Aggregation100

Aggregation Mode: Dynamic

Loadsharing Type: Shar

Management VLANs: None

System ID: 0x8000, 8e33-8e4a-0300

Local:

  Port                Status   Priority Index    Oper-Key               Flag

  XGE1/0/1            S        32768    1        1                      {ACDEF}

  XGE1/0/2            S        32768    2        1                      {ACDEF}

Remote:

  Actor               Priority Index    Oper-Key SystemID               Flag

  XGE1/0/1(R)         32768    16386    40001    0x7b  , 0001-0001-0001 {ACDEF}

  XGE1/0/2            32768    32770    40001    0x7b  , 0001-0001-0001 {ACDEF}

# Verify that all member ports of aggregation group 101 are in Selected state on Device D, which indicates a successful link aggregation between the DR system and Device D.

[DeviceD] display link-aggregation verbose

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port, M -- Management port, R -- Reference port

Flags:  A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

        D -- Synchronization, E -- Collecting, F -- Distributing,

        G -- Defaulted, H -- Expired

 

Aggregate Interface: Bridge-Aggregation101

Aggregation Mode: Dynamic

Loadsharing Type: Shar

Management VLANs: None

System ID: 0x8000, 8e33-9400-0400

Local:

  Port                Status   Priority Index    Oper-Key               Flag

  XGE1/0/1            S        32768    1        1                      {ACDEF}

  XGE1/0/2            S        32768    2        1                      {ACDEF}

Remote:

  Actor               Priority Index    Oper-Key SystemID               Flag

  XGE1/0/1(R)         32768    16387    40002    0x7b  , 0001-0001-0001 {ACDEF}

  XGE1/0/2            32768    32771    40002    0x7b  , 0001-0001-0001 {ACDEF}

# Verify that Device A is the master in VRRP group 1 and Device B is the master in VRRP group 2.

[DeviceA] display vrrp

IPv4 Virtual Router Information:

 Running mode : Standard

 Total number of virtual routers : 2

 Interface          VRID  State        Running Adver   Auth     Virtual

                                       Pri     Timer   Type        IP

 ---------------------------------------------------------------------

 Vlan100            1     Master       200     100     None     100.1.1.100

 Vlan101            2     Backup       100     100     None     101.1.1.100

[DeviceB] display vrrp

IPv4 Virtual Router Information:

 Running mode : Standard

 Total number of virtual routers : 2

 Interface          VRID  State        Running Adver   Auth     Virtual

                                       Pri     Timer   Type        IP

 ---------------------------------------------------------------------

 Vlan100            1     Backup       100     100     None     100.1.1.100

 Vlan101            2     Master       200     100     None     101.1.1.100

# Verify that Device E has established OSPF neighbor relationships with Device A and Device B.

[DeviceE] display ospf peer

 

         OSPF Process 1 with Router ID 30.1.1.1

               Neighbor Brief Information

 

 Area: 0.0.0.0

 Router ID       Address         Pri Dead-Time  State             Interface

 101.1.1.1       10.1.1.1        1   34         Full/DR           Vlan10

 101.1.1.2       20.1.1.1        1   36         Full/DR           Vlan20

# Verify that a host in Area A can ping the host at 101.1.1.4 in Area B.

C:\Documents and Settings\Administrator>ping 101.1.1.4

 

Pinging 101.1.1.4 with 32 bytes of data:

 

Reply from 101.1.1.4: bytes=32 time=1ms TTL=126

Reply from 101.1.1.4: bytes=32 time=1ms TTL=126

Reply from 101.1.1.4: bytes=32 time=1ms TTL=126

Reply from 101.1.1.4: bytes=32 time=1ms TTL=126

 

Ping statistics for 101.1.1.4:

    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

Approximate round trip times in milli-seconds:

    Minimum = 1ms, Maximum = 1ms, Average = 1ms

# Verify that a host in Area A can ping VLAN-interface 30 (30.1.1.1) on Device E.

C:\Documents and Settings\Administrator>ping 30.1.1.1

 

Pinging 30.1.1.1 with 32 bytes of data:

 

Reply from 30.1.1.1: bytes=32 time=1ms TTL=126

Reply from 30.1.1.1: bytes=32 time=1ms TTL=126

Reply from 30.1.1.1: bytes=32 time=1ms TTL=126

Reply from 30.1.1.1: bytes=32 time=1ms TTL=126

 

Ping statistics for 30.1.1.1:

    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

Approximate round trip times in milli-seconds:

    Minimum = 1ms, Maximum = 1ms, Average = 1ms

Configuration files

·          Device A:

#

ospf 1

 area 0.0.0.0

  network 10.1.1.0 0.0.0.255

  network 100.1.1.0 0.0.0.255

  network 101.1.1.0 0.0.0.255

#

vlan 10

#

vlan 100 to 101

#

interface Bridge-Aggregation100

 port link-type trunk

 port trunk permit vlan 1 100

 link-aggregation mode dynamic

 port drni group 1

#

interface Bridge-Aggregation101

 port link-type trunk

 port trunk permit vlan 1 101

 link-aggregation mode dynamic

 port drni group 2

#

interface Bridge-Aggregation125

 port link-type trunk

 port trunk permit vlan 1 100 to 101

 link-aggregation mode dynamic

 port drni intra-portal-port 1

#

interface Vlan-interface10

 ip address 10.1.1.1 255.255.255.0

#

interface Vlan-interface100

 ip address 100.1.1.1 255.255.255.0

 vrrp vrid 1 virtual-ip 100.1.1.100

 vrrp vrid 1 priority 200

 vrrp vrid 1 preempt-mode delay 500

 vrrp vrid 1 track 1 priority reduced 150

#

interface Vlan-interface101

 ip address 101.1.1.1 255.255.255.0

 vrrp vrid 2 virtual-ip 101.1.1.100

#

interface Ten-GigabitEthernet1/0/5

 port link-mode route

 ip address 1.1.1.1 255.255.255.0

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 100

 port link-aggregation group 100

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 101

 port link-aggregation group 101

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 100 to 101

 port link-aggregation group 125

#

interface Ten-GigabitEthernet1/0/4

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 100 to 101

 port link-aggregation group 125

#

interface Ten-GigabitEthernet1/0/6

 port link-mode bridge

 port access vlan 10

#

 drni system-mac 0001-0001-0001

 drni system-number 1

 drni system-priority 123

 drni keepalive ip destination 1.1.1.2 source 1.1.1.1

#

 mad exclude interface Ten-GigabitEthernet1/0/5

#

 track 1 interface Ten-GigabitEthernet1/0/6

#

·          Device B:

#

ospf 1

 area 0.0.0.0

  network 20.1.1.0 0.0.0.255

  network 100.1.1.0 0.0.0.255

  network 101.1.1.0 0.0.0.255

#

vlan 20

#

vlan 100 to 101

#

interface Bridge-Aggregation100

 port link-type trunk

 port trunk permit vlan 1 100

 link-aggregation mode dynamic

 port drni group 1

#

interface Bridge-Aggregation101

 port link-type trunk

 port trunk permit vlan 1 101

 link-aggregation mode dynamic

 port drni group 2

#

interface Bridge-Aggregation125

 port link-type trunk

 port trunk permit vlan 1 100 to 101

 link-aggregation mode dynamic

 port drni intra-portal-port 1

#

interface Vlan-interface20

 ip address 20.1.1.1 255.255.255.0

#

interface Vlan-interface100

 ip address 100.1.1.2 255.255.255.0

 vrrp vrid 1 virtual-ip 100.1.1.100

#

interface Vlan-interface101

 ip address 101.1.1.2 255.255.255.0

 vrrp vrid 2 virtual-ip 101.1.1.100

 vrrp vrid 2 priority 200

 vrrp vrid 2 preempt-mode delay 500

 vrrp vrid 2 track 2 priority reduced 150

#

interface Ten-GigabitEthernet1/0/5

 port link-mode route

 ip address 1.1.1.2 255.255.255.0

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 101

 port link-aggregation group 101

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 100

 port link-aggregation group 100

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 100 to 101

 port link-aggregation group 125

#

interface Ten-GigabitEthernet1/0/4

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 100 to 101

 port link-aggregation group 125

#

interface Ten-GigabitEthernet1/0/6

 port link-mode bridge

 port access vlan 20

#

 drni system-mac 0001-0001-0001

 drni system-number 2

 drni system-priority 123

 drni keepalive ip destination 1.1.1.1 source 1.1.1.2

#

 mad exclude interface Ten-GigabitEthernet1/0/5

#

 track 2 interface Ten-GigabitEthernet1/0/6

#

·          Device C:

#

vlan 100

#

interface Bridge-Aggregation100

 port link-type trunk

 port trunk permit vlan 1 100

 link-aggregation mode dynamic

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 100

 port link-aggregation group 100

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 100

 port link-aggregation group 100

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port access vlan 100

#

·          Device D:

#

vlan 101

#

interface Bridge-Aggregation101

 port link-type trunk

 port trunk permit vlan 1 101

 link-aggregation mode dynamic

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 101

 port link-aggregation group 101

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port link-type trunk

 port trunk permit vlan 1 101

 port link-aggregation group 101

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port access vlan 101

#

·          Device E:

#

ospf 1

 area 0.0.0.0

  network 10.1.1.0 0.0.0.255

  network 20.1.1.0 0.0.0.255

  network 30.1.1.0 0.0.0.255

#

vlan 10

#

vlan 20

#

vlan 30

#

interface Vlan-interface10

 ip address 10.1.1.2 255.255.255.0

#

interface Vlan-interface20

 ip address 20.1.1.2 255.255.255.0

#

interface Vlan-interface30

 ip address 30.1.1.1 255.255.255.0

#

interface Ten-GigabitEthernet1/0/1

 port link-mode bridge

 port access vlan 10

#

interface Ten-GigabitEthernet1/0/2

 port link-mode bridge

 port access vlan 20

#

interface Ten-GigabitEthernet1/0/3

 port link-mode bridge

 port access vlan 30

#

Related documentation

·          H3C S6890 Switch Series Layer 2—LAN Switching Command Reference (R27xx)

·          H3C S6890 Switch Series Layer 2—LAN Switching Configuration Guide (R27xx)