- 产品与解决方案
- 行业解决方案
- 服务
- 支持
- 合作伙伴
- 关于我们
03-H3C_软件升级配置举例
本章节下载： 03-H3C_软件升级配置举例 (285.33 KB)
H3C软件升级配置举例
|
Copyright © 2017新华三技术有限公司 版权所有，保留一切权利。 非经本公司书面许可，任何单位和个人不得擅自摘抄、复制本文档内容的部分或全部， 并不得以任何形式传播。本文档中的信息可能变动，恕不另行通知。 |
|
目 录
本文档介绍软件升级的典型配置举例。
本文档不严格与具体软、硬件版本对应，如果使用过程中与产品实际情况有差异，请参考相关产品手册，或以设备实际情况为准。
本文档中的配置均是在实验室环境下进行的配置和验证，配置前设备的所有参数均采用出厂时的缺省配置。如果您已经对设备进行了配置，为了保证配置效果，请确认现有配置和以下举例中的配置不冲突。
本文档假设您已了解软件升级和FTP/TFTP的特性。
如图3-1所示，Device和文件服务器通过交换机相连，Device作为TFTP客户端，文件服务器作为TFTP服务器。现要求：通过TFTP方式将存储在文件服务器上的文件new.ipe下载到TFTP客户端，为Device升级软件版本。
为了使设备在重启后使用新版本软件，需要指定下次启动时所用的主用启动文件为升级后的软件版本。
本举例是在S3210-CMW710-R7566版本上进行配置和验证的。
· 当设备剩余的存储空间不够，请使用delete /unreserved file-url命令删除部分暂时不用的文件后再执行升级软件操作。
· 软件升级时需要重启设备，建议使用save命令保存设备的当前配置。
# 配置文件服务器的IP地址为192.168.100.14/24，使得与Device路由可达，具体配置方法略。
# 启动文件服务器上的TFTP功能（以3CDaemon软件为例），设置TFTP服务器下载路径等参数，并开启服务。
图3-2 配置TFTP服务器
# 配置Device接口IP地址。
<Device> system-view
[Device] interface GigabitEthernet1/0/24
[Device-GigabitEthernet1/0/24] ip address 192.168.100.66 255.255.255.0
[Device-GigabitEthernet1/0/24] quit
[Device] quit
# 在Device ping 文件服务器地址，能够ping通。
<Device> ping 192.168.100.14
Ping 192.168.100.14 (192.168.100.14): 56 data bytes, press CTRL_C to break
56 bytes from 192.168.100.14: icmp_seq=0 ttl=64 time=10.701 ms
56 bytes from 192.168.100.14: icmp_seq=1 ttl=64 time=2.678 ms
56 bytes from 192.168.100.14: icmp_seq=2 ttl=64 time=2.282 ms
56 bytes from 192.168.100.14: icmp_seq=3 ttl=64 time=1.617 ms
56 bytes from 192.168.100.14: icmp_seq=4 ttl=64 time=1.701 ms
--- Ping statistics for 192.168.100.14 ---
5 packet(s) transmitted, 5 packet(s) received, 0.0% packet loss
round-trip min/avg/max/std-dev = 1.617/3.796/10.701/3.474 ms
# 执行save命令保存交换机当前配置信息。
<Device> save
The current configuration will be written to the device. Are you sure? [Y/N]:y
Please input the file name(*.cfg)[flash:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):
flash:/startup.cfg exists, overwrite? [Y/N]:y
Validating file. Please wait...
Saved the current configuration to mainboard device successfully.
# 执行display device命令查看当前设备信息。
<Device> display device
Slot Type State Subslot Soft Ver Patch Ver
1 S3210-16P-OLT Master 0 S3210-7565P01 None
# 使用TFTP方式将文件服务器上的new.ipe文件下载到Device上，以缺省文件名new.ipe保存。
<Device> tftp 192.168.100.14 get new.ipe
% Total % Received % Xferd Average Speed Time Time Time Current
Dload Upload Total Spent Left Speed
100 70.7M 100 70.7M 0 0 1193k 0 0:00:50 0:00:50 --:--:-- 1127k
# 指定Device下次启动时所用的主用启动文件。
<Device> boot-loader file flash:/new.ipe slot 1 main
Verifying the file flash:/new.ipe on slot 1..................................
...............................Done.
H3C S3210-16P-OLT images in IPE:
BOOT-test.bin
SYSTEM-test.bin
This command will set the main startup software images. Continue? [Y/N]:y
Add images to slot 1.
Decompressing file BOOT-test.bin to flash:/BOOT-test.bin..........................................Done.
Decompressing file SYSTEM-test.bin to flash:/SYSTEM-test.bin.......................
................................................................................
................................................................................
...................................................................Done.
Decompression completed.
You are recommended to delete the .ipe file after you set startup software image
s for all slots.
Do you want to delete flash:/new.ipe now? [Y/N]:y
The images that have passed all examinations will be used as the main startup so
ftware images at the next reboot on slot 1.
# 指定Device下次启动时所用的备用启动文件。
<Device> boot-loader file boot flash:/BOOT-old.bin system flash:/SYSTEM-old.bin slot 1 backup
This command will set the backup startup software images. Continue? [Y/N]:y
Verifying the file flash:/BOOT-old.bin on slot 1............Done
.
Verifying the file flash:/SYSTEM-old.bin on slot 1..............
.......................................................................Done.
The images that have passed all examinations will be used as the backup startup
software images at the next reboot on slot 1.
# 重启设备。
<Device> reboot
# 设备重启后，使用display version命令查看设备版本信息。
<Device> display version
H3C Comware Software, Version 7.1.070, ESS 7565P01
Copyright (c) 2004-2017 New H3C Technologies Co., Ltd. All rights reserved.
H3C S3210-16P-OLT uptime is 0 weeks, 0 days, 0 hours, 27 minutes
Last reboot reason : USER reboot
Boot image: flash:/BOOT-R7566.bin
Boot image version: 7.1.070, Release R7566
Compiled Jul 15 2016 16:00:00
System image: flash:/SYSTEM-R7566.bin
System image version: 7.1.070, Release R7566
Compiled Jul 15 2016 16:00:00
……略……
# 显示设备本次启动和下次启动所采用的启动软件包的名称。
<Device> display boot-loader
Software images on slot 1:
Current software images:
flash:/BOOT-test.bin
flash:/SYSTEM-test.bin
Main startup software images:
flash:/BOOT-test.bin
flash:/SYSTEM-test.bin
Backup startup software images:
flash:/BOOT-old.bin
flash:/SYSTEM-old.bin
#
interface GigabitEthernet1/0/24
combo enable copper
ip address 192.168.100.66 255.255.255.0
#
如图4-1所示，Device和文件服务器通过交换机相连，Device作为FTP客户端，文件服务器作为FTP服务器。现要求：通过FTP方式将存储在文件服务器上的文件new.ipe下载到FTP客户端，为Device升级软件版本。
为了使交换机在重启后使用新版本软件，需要指定下次启动时所用的主用启动文件为升级后的软件版本。
本举例是在S3210-CMW710-R7566版本上进行配置和验证的。
· 当设备剩余的存储空间不够，请使用delete /unreserved file-url命令删除部分暂时不用的文件后再执行升级软件操作。
· 软件升级时需要重启设备，建议使用save命令保存设备的当前配置。
# 配置文件服务器的IP地址为192.168.100.14/24，使得与Device路由可达，具体配置方法略。
# 启动文件服务器上的FTP功能（以3CDaemon软件为例），设置FTP服务器下载路径等参数，并开启服务。
图4-2 配置FTP服务器
# 配置Device接口IP地址。
<Device> system-view
[Device] interface GigabitEthernet1/0/24
[Device-GigabitEthernet1/0/24] ip address 192.168.100.66 255.255.255.0
[Device-GigabitEthernet1/0/24] quit
[Device] quit
# 在Device ping 文件服务器地址，能够ping通。
<Device> ping 192.168.100.14
Ping 192.168.100.14 (192.168.100.14): 56 data bytes, press CTRL_C to break
56 bytes from 192.168.100.14: icmp_seq=0 ttl=64 time=10.701 ms
56 bytes from 192.168.100.14: icmp_seq=1 ttl=64 time=2.678 ms
56 bytes from 192.168.100.14: icmp_seq=2 ttl=64 time=2.282 ms
56 bytes from 192.168.100.14: icmp_seq=3 ttl=64 time=1.617 ms
56 bytes from 192.168.100.14: icmp_seq=4 ttl=64 time=1.701 ms
--- Ping statistics for 192.168.100.14 ---
5 packet(s) transmitted, 5 packet(s) received, 0.0% packet loss
round-trip min/avg/max/std-dev = 1.617/3.796/10.701/3.474 ms
# 执行save命令保存交换机当前配置信息。
<Device> save
The current configuration will be written to the device. Are you sure? [Y/N]:y
Please input the file name(*.cfg)[flash:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):
flash:/startup.cfg exists, overwrite? [Y/N]:y
Validating file. Please wait...
Saved the current configuration to mainboard device successfully.
# 执行display device命令查看当前设备信息。
<Device> display device
Slot Type State Subslot Soft Ver Patch Ver
1 S3210-16P-OLT Master 0 S3210-7565P01 None
# 以用户名123456、密码123456登录FTP服务器。
<Device> ftp 192.168.100.14
Connected to 192.168.100.14 (192.168.100.14).
220 3Com 3CDaemon FTP Server Version 2.0
User (192.168.100.14:(none)): 123456
331 User name ok, need password
Password:
230 User logged in
Remote system type is UNIX.
Using binary mode to transfer files.
# 将文件new.ipe从FTP服务器下载到Device。
ftp> get new.ipe
227 Entering passive mode (192,168,100,14,8,86)
125 Using existing data connection
226 Closing data connection; File transfer successful.
70445056 bytes received in 53.6 seconds (1.25 Mbyte/s)
ftp> quit
# 指定Device下次启动时所用的主用启动文件。
<Device> boot-loader file flash:/new.ipe slot 1 main
Verifying the file flash:/new.ipe on slot 1..................................
...............................Done.
H3C S3210-16P-OLT images in IPE:
BOOT-test.bin
SYSTEM-test.bin
This command will set the main startup software images. Continue? [Y/N]:y
Add images to slot 1.
Decompressing file BOOT-test.bin to flash:/BOOT-test.bin..........................................Done.
Decompressing file SYSTEM-test.bin to flash:/SYSTEM-test.bin..........................................................
................................................................................
...................................................................Done.
Decompression completed.
Verifying the file flash:/BOOT-test.bin on slot 1...Done.
Verifying the file flash:/SYSTEM-test.bin on slot 1.............Done.
The images that have passed all examinations will be used as the main startup so
ftware images at the next reboot on slot 1.
# 指定Device下次启动时所用的备用启动文件。
<Device> boot-loader file boot flash:/BOOT-old.bin system flash:/SYSTEM-old.bin slot 1 backup
This command will set the backup startup software images. Continue? [Y/N]:y
Verifying the file flash:/Boot-old.bin on slot 1............Done
.
Verifying the file flash:/SYSTEM-old.bin on slot 1..............
.......................................................................Done.
The images that have passed all examinations will be used as the backup startup
software images at the next reboot on slot 1.
# 重启设备。
<Device> reboot
# 设备重启后，使用display version命令查看设备版本信息。
<Device> display version
H3C Comware Software, Version 7.1.070, Release 7566
Copyright (c) 2004-2017 New H3C Technologies Co., Ltd. All rights reserved.
H3C S3210-16P-OLT uptime is 0 weeks, 0 days, 0 hours, 4 minutes
Last reboot reason : USER reboot
Boot image: flash:/BOOT-R7566.bin
Boot image version: 7.1.070, Release 7566
Compiled Jul 15 2016 16:00:00
System image: flash:/SYSTEM-R7566.bin
System image version: 7.1.070, Release 7566
Compiled Jul 15 2016 16:00:00
……略……
# 显示设备下次启动所采用的启动软件包的名称。
<Device> display boot-loader
Software images on slot 1:
Current software images:
flash:/BOOT-test.bin
flash:/SYSTEM-test.bin
Main startup software images:
flash:/BOOT-test.bin
flash:/SYSTEM-test.bin
Backup startup software images:
flash:/BOOT-old.bin
flash:/SYSTEM-old.bin
#
interface GigabitEthernet1/0/24
combo enable copper
ip address 192.168.100.66 255.255.255.0
#
如图5-1所示，Device和文件服务器通过交换机相连，Device作为FTP服务器，文件服务器作为FTP客户端。
现要求：
· 通过FTP方式为Device升级软件版本，将存储在FTP客户端上的文件new.ipe上传到FTP服务器。
· 配置FTP客户端登录FTP服务器的用户名为abc，密码为123456。
为了使交换机在重启后使用新软件版本，需要指定下次启动时所用的主用启动文件为升级后的软件版本。
本举例是在S3210-CMW710-R7566版本上进行配置和验证的。
· 当设备剩余的内存空间不够，请使用delete /unreserved file-url命令删除部分暂时不用的文件后再执行升级软件操作。
· 确保主机和Device的FTP用户名、密码及文件名等参数保持一致。
· 在Device和主机之间进行FTP传输，需要选择binary方式传输文件。
# 配置Device接口IP地址。
<Device> system-view
[Device] interface GigabitEthernet1/0/24
[Device-GigabitEthernet1/0/24] ip address 192.168.100.66 255.255.255.0
[Device-GigabitEthernet1/0/24] quit
# 在Device上添加一个FTP用户abc，并设置其认证密码为123456。
[Device] local-user abc
[Device-luser-abc] password simple 123456
# 配置用户角色为network-admin。
[Device-luser-abc] authorization-attribute user-role network-admin
# 为保证FTP用户仅使用授权的用户角色network-admin，删除缺省用户角色network-operator。
[Device-luser-abc] undo authorization-attribute user-role network-operator
# 配置服务类型为FTP。
[Device-luser-abc] service-type ftp
[Device-luser-abc] quit
# 启动Device的FTP服务功能。
[Device] ftp server enable
[Device] quit
# 执行save命令保存交换机当前配置信息。
<Device> save
The current configuration will be written to the device. Are you sure? [Y/N]:y
Please input the file name(*.cfg)[flash:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):
flash:/startup.cfg exists, overwrite? [Y/N]:y
Validating file. Please wait...
Saved the current configuration to mainboard device successfully.
# 配置主机文件服务器的IP地址为192.168.100.14/24，使得到Device路由可达，具体配置方法略。
# 从FTP客户端登录FTP服务器，本例以Windows命令提示符界面为例。
C:\Documents and Settings\Administrator> ftp 192.168.100.66
Connected to 192.168.100.66.
220 FTP service ready.
# 以用户名abc、密码123456登录FTP服务器。
User (192.168.100.66:(none)): abc
331 Password required for abc.
Password:
230 User logged in.
# 使用lcd命令，将FTP客户端本地的工作路径切换到软件版本所在的目录下。
ftp> lcd E:\
Local directory now E:\
# 将传输模式设置为binary方式。
ftp> binary
200 TYPE is now 8-bit binary
# 将本地new.ipe文件上传到FTP服务器上，缺省以文件名new.ipe保存。
ftp> put new.ipe
200 PORT command successful
150 Connecting to port 2903
226 File successfully transferred
ftp: 发送 70445056 字节，用时 1.05Seconds 67282.77Kbytes/sec.
# 使用ls命令查看FTP服务器上是否有文件。
ftp> ls new.ipe
200 PORT command successful
150 Connecting to port 3391
new.ipe
226 1 matches total
ftp: 收到 24 字节，用时 0.00Seconds 24000.00Kbytes/sec.
# 终止与FTP服务器的连接，并退回到用户视图。
ftp> bye
# 执行display device命令查看当前设备信息。
<Device> display device
Slot Type State Subslot Soft Ver Patch Ver
1 S3210-16P-OLT Master 0 S3210-7565P01 None
# 指定Device下次启动时所用的主用启动文件。
<Device> boot-loader file flash:/new.ipe slot 1 main
Verifying the file flash:/new.ipe on slot 1..................................
...............................Done.
H3C S3210-16P-OLT images in IPE:
BOOT-test.bin
SYSTEM-test.bin
This command will set the main startup software images. Continue? [Y/N]:y
Add images to slot 1.
Decompressing file BOOT-test.bin to flash:/BOOT-test.bin..........................................Done.
Decompressing file SYSTEM-test.bin to flash:/SYSTEM-test.bin...........................................................
................................................................................
................................................................................
...................................................................Done.
Decompression completed.
Verifying the file flash:/BOOT-test.bin on slot 1...Done.
Verifying the file flash:/SYSTEM-test.bin on slot 1.............Done.
The images that have passed all examinations will be used as the main startup so
ftware images at the next reboot on slot 0.
# 指定Device下次启动时所用的备用启动文件。
<Device> boot-loader file boot flash:/BOOT-old.bin system flash:/SYSTEM-old.bin slot 1 backup
This command will set the backup startup software images. Continue? [Y/N]:y
Verifying the file flash:/BOOT-old.bin on slot 1...........Done
.
Verifying the file flash:/SYSTEM-old.bin on slot 1..............
.......................................................................Done.
The images that have passed all examinations will be used as the backup startup
software images at the next reboot on slot 1.
# 重启设备。
<Device> reboot
# 设备重启后，使用display version命令查看设备版本信息。
<Device> display version
H3C Comware Software, Version 7.1.070, Release 7566
Copyright (c) 2004-2017 New H3C Technologies Co., Ltd. All rights reserved.
H3C S3210-16P-OLT uptime is 0 weeks, 0 days, 0 hours, 4 minutes
Last reboot reason : USER reboot
Boot image: flash:/BOOT-R7566.bin
Boot image version: 7.1.070, Release 7566
Compiled Jul 15 2016 16:00:00
System image: flash:/SYSTEM-R7566.bin
System image version: 7.1.070, Release 7566
Compiled Jul 15 2016 16:00:00
……略……
# 显示设备本次启动和下次启动所采用的启动软件包的名称。
<Device> display boot-loader
Software images on slot 1:
Current software images:
flash:/BOOT-test.bin
flash:/SYSTEM-test.bin
Main startup software images:
flash:/BOOT-test.bin
flash:/SYSTEM-test.bin
Backup startup software images:
flash:/BOOT-old.bin
flash:/SYSTEM-old.bin
#
interface GigabitEthernet1/0/24
ip address 192.168.100.66 255.255.255.0
combo enable copper
#
local-user abc class manage
password hash $h$6$YMVbbwFL/vviWcQu$+CuTbYCehNZtZo5RCXiadpYbXYWa2omt5TUtEh3UPCg3fZjxYCp5WzbuE2GoowVi2YA/BK+mnSZJZqi5jRDuCg==
service-type ftp
authorization-attribute user-role network-admin
#
ftp server enable
#
如图6-1所示，文件服务器与Device的以太网接口GigabitEthernet1/0/24相连，Host通过串口线连接Device的Console口。现由于设备问题，不能正常启动Device。
现要求：使用BootWare菜单升级Device的软件版本。
本举例是在S3210-CMW710-R7566版本上进行配置和验证的。
· 确保在文件服务器上开启TFTP服务器功能。
· 当设备剩余的存储空间不够，请使用delete /unreserved file-url命令删除部分暂时不用的文件后，再执行升级软件操作。
· 将交换机的升级启动文件拷贝到文件服务器上，并正确设置TFTP服务器的访问路径。
# 使用串口线，从主机连至Device的Console口。
# 通过超级终端或PuTTY等终端仿真程序与设备建立连接。这些程序的详细介绍和使用方法请参见该程序的使用指导。打开终端仿真程序后，请按如下要求设置终端参数：
· 波特率：9600
· 数据位：8
· 停止位：1
· 奇偶校验：无
· 流量控制：无
# 配置文件服务器的IP地址为192.168.100.14/24，具体配置步骤略。
# 启动文件服务器的TFTP服务器（以3CDaemon软件为例），设置TFTP服务器下载路径等参数，并开启服务。
图6-2 配置TFTP服务器
# 使用直通线从TFTP服务器连接到设备的以太网接口GigabitEthernet 1/0/24上（已使用串口线从主机连接至Device的Console口）。
# 将设备的当前配置保存到指定文件。
[Device] save
The current configuration will be written to the device. Are you sure? [Y/N]:y
Please input the file name(*.cfg)[flash:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):
flash:/startup.cfg exists, overwrite? [Y/N]:y
Validating file. Please wait...
Saved the current configuration to mainboard device successfully.
[Device] quit
# 重启设备。
<Device> reboot
# 交换机上加电重启的过程中，在配置终端的屏幕上将显示：
RAM test successful.
Press Ctrl+T to start five-step full RAM test...
Press Ctrl+Y to start nine-step full RAM test...
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU...
Booting Normal Extended BootWare
The Extended BootWare is self-decompressing.........Done.
****************************************************************************
* *
* BootWare, Version 0.01 *
* *
****************************************************************************
Compiled Date : Mar 30 2017, 19:48:57
CPU Type : bcm_arm
CPU Clock Speed : 1000MHz
Memory Type : DDR3 SDRAM
Memory Size : 2048MB
Memory Speed : 750MHz
Flash Size : 1024MB
BASIC CPLD Version : 001
EXTENDED CPLD Version : 001
PCB Version : Ver.A
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
# 当出现“Press Ctrl+B to access EXTENDED-BOOTWARE MENU”时，键入<Ctrl+B>，系统提示：
Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+A: Enter Command Line
Ctrl+F: Format File System
Ctrl+C: Display Copyright
# 在BootWare菜单下键入<3>，进入以太网口子菜单，系统显示如下：
Enter your choice(0-9): 3
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
# 在以太网口子菜单下键入<5>就可以进入以太网口配置菜单，并按照如下方式分别配置Load File Name、Target File Name、Server IP Address、Local IP Address、Subnet Mask、Gateway IP Address：
· Load File Name：待升级Device的启动软件包的名称，该文件位于TFTP服务器的工作目录下。
· Target File Name：启动软件包上传至Device的存储介质后的文件名。
· Server IP Address：TFTP服务器的IP地址。
· Local IP Address：Device连接文件服务器的端口IP地址。
· Subnet Mask：子网掩码。
· Gateway IP Address：网关地址，当TFTP服务器与待升级的Device不在同一网段时，必须配置该地址。
Enter your choice(0-5): 5
==========================<ETHERNET PARAMETER SET>==========================
|Note: '.' = Clear field. |
| '-' = Go to previous field. |
| Ctrl+D = Quit. |
============================================================================
· 使用TFTP方式下载软件版本：
Protocol (FTP or TFTP) :tftp
· 加载软件版本new.ipe：
Load File Name : new.ipe
:
Target File Name : new.ipe
:
· 输入TFTP服务器地址：
Server IP Address :192.168.1.100 192.168.100.14
· 输入Device管理IP地址（只需要和TFTP服务器路由可达，这里以192.168.100.66为例）：
Local IP Address :192.168.1.1 192.168.100.66
· 输入子网掩码255.255.255.0：
Subnet Mask :255.255.255.0
Gateway IP Address :0.0.0.0
# 按下Enter键，进入如下界面：
===========================<Enter Ethernet SubMenu>=========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Serial Interface Parameter |
|<0> Exit To Main Menu |
============================================================================
# 在以太网口配置子菜单下，键入<2>为升级主启动文件：
Enter your choice(0-5): 2
Loading.....................................................................
............................................................................
............................................................................
.................................................Done.
227301376 bytes downloaded!
Image file BOOT-test.bin is self-decompressing...
Saving file flash:/BOOT-test.bin ..........................
........................................................Done.
Image file SYSTEM-test.bin is self-decompressing...
Saving file flash:/SYSTEM-test.bin .........................................
............................................................................
............................................................................
............................................................................
............Done.
===========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Serial Interface Parameter |
|<0> Exit To Main Menu |
============================================================================
# 键入<0>，返回BootWare主菜单：
Enter your choice(0-5): 0
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+A: Enter Command Line
Ctrl+F: Format File System
# 键入<1>，进入引导系统：
Enter your choice(0-9): 1
Loading the main image files...
Loading file flash:/SYSTEM-test.bin........................
............................................................................
............................................................................
.........................Done.
Loading file flash:/BOOT-test.bin..........................
....Done.
Image file flash:/BOOT-test.bin is self-decompressing......
....................................................Done.
System image is starting...
Line aux1 is available.
Press ENTER to get started.
# 设备重启后，使用display version命令查看设备版本信息。
<Device> display version
H3C Comware Software, Version 7.1.070, Release 7566
Copyright (c) 2004-2017 New H3C Technologies Co., Ltd. All rights reserved.
H3C S3210-16P-OLT uptime is 0 weeks, 0 days, 0 hours, 4 minutes
Last reboot reason : USER reboot
Boot image: flash:/BOOT-R7566.bin
Boot image version: 7.1.070, Release 7566
Compiled Jul 15 2016 16:00:00
System image: flash:/SYSTEM-R7566.bin
System image version: 7.1.070, Release 7566
Compiled Jul 15 2016 16:00:00
……略……
# 显示设备本次启动和下次启动所采用的启动软件包的名称。
<Device> display boot-loader
Software images on slot 1:
Current software images:
flash:/BOOT-test.bin
flash:/SYSTEM-test.bin
Main startup software images:
flash:/BOOT-test.bin
flash:/SYSTEM-test.bin
Backup startup software images:
flash:/BOOT-old.bin
flash:/SYSTEM-old.bin
无
· H3C S3210系列以太网PON OLT交换机 基础配置指导-R7566
· H3C S3210系列以太网PON OLT交换机 基础配置命令参考-R7566
不同款型规格的资料略有差异, 详细信息请向具体销售和400咨询。H3C保留在没有任何通知或提示的情况下对资料内容进行修改的权利!
支持
