Contents

Configuring service loopback groups· 1

About service loopback groups· 1

Restrictions and guidelines: Service loopback group configuration· 1

Configuring a service loopback group· 1

Display and maintenance commands for service loopback groups· 2

Service loopback group configuration examples· 2

Example: Configuring a service loopback group· 2

Configuring service loopback groups

About service loopback groups

A service loopback group contains one or multiple Ethernet ports for looping packets sent out by the device back to the device. This feature must work with other features, such as GRE. Member ports in a service loopback group are load balanced.

A service loopback group provides one of the following services:

·     Tunnel—Supports unicast tunnel services.

·     Multicast tunnel—Supports multicast tunnel services.

·     Multiport—Supports multiport ARP services.

·     VSI gateway—Supports VSI gateway services.

·     Mirror—Supports flow mirror services.

Restrictions and guidelines: Service loopback group configuration

When you add member ports to a service loopback group, follow these restrictions and guidelines:

·     Make sure the ports support the service type of the service loopback group and are not members of any other service loopback group.

When you apply service loopback groups to features, follow these restrictions and guidelines:

·     A service loopback group can process services only after it is used by other features. You can apply a service loopback group to other features once the group is created. One service loopback group can be used by multiple features.

·     You cannot change the service type of a service loopback group.

·     Do not delete a service loopback group that is being used by a feature.

Configuring a service loopback group

1.     Enter system view.

system-view

2.     Create a service loopback group and specify its service type.

service-loopback group group-id type { mirror | { multicast-tunnel | tunnel } * | multiport | vsi-gateway }

You can configure only one service loopback group for a service type.

3.     Enter Layer 2 Ethernet interface view.

interface interface-type interface-number

4.     Assign the port to the service loopback group.

port service-loopback group group-id

By default, a port does not belong to a service loopback group.

You can assign a maximum of 32 ports to a service loopback group.

Display and maintenance commands for service loopback groups

Execute display commands in any view.

Service loopback group configuration examples

Example: Configuring a service loopback group

Network configuration

All Ethernet ports on the device support unicast tunnel services. Assign Ten-GigabitEthernet 1/0/1 through Ten-GigabitEthernet 1/0/3 to a service loopback group to loop GRE packets sent out by the device back to the device.

Procedure

# Create service loopback group 1, and specify its service type as tunnel.

<Sysname> system-view

[Sysname] service-loopback group 1 type tunnel

# Assign Ten-GigabitEthernet 1/0/1 through Ten-GigabitEthernet 1/0/3 to service loopback group 1.

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] port service-loopback group 1

All configurations on the interface will be lost. Continue?[Y/N]:y [Sysname-Ten-GigabitEthernet1/0/1] quit

[Sysname] interface ten-gigabitethernet 1/0/2

[Sysname-Ten-GigabitEthernet1/0/2] port service-loopback group 1

All configurations on the interface will be lost. Continue?[Y/N]:y [Sysname-Ten-GigabitEthernet1/0/2] quit

[Sysname] interface ten-gigabitethernet 1/0/3

[Sysname-Ten-GigabitEthernet1/0/3] port service-loopback group 1

All configurations on the interface will be lost. Continue?[Y/N]:y [Sysname-Ten-GigabitEthernet1/0/3] quit

# Create the interface Tunnel 1 and set it to GRE mode. The interface will automatically use service loopback group 1.

[Sysname] interface tunnel 1 mode gre

[Sysname-Tunnel1]