Contents

Introduction· 1

Prerequisites· 1

Example: Configuring GTS and rate limiting· 1

Network configuration· 1

Analysis· 1

Applicable hardware and software versions· 2

Procedures· 3

Configuring priority marking· 3

Configuring GTS· 4

Configuring rate limiting· 4

Verifying the configuration· 4

Configuration files· 5

 

Introduction

This document provides GTS and rate limiting configuration examples.

Prerequisites

The configuration examples in this document were created and verified in a lab environment, and all the devices were started with the factory default configuration. When you are working on a live network, make sure you understand the potential impact of every command on your network.

This document assumes that you have basic knowledge of GTS and rate limiting.

Example: Configuring GTS and rate limiting

Network configuration

As shown in Figure 1, the 15-Mbps dedicated line transmits the FTP traffic, business-specific application traffic, and IP voice traffic between the headquarters and branch of a company.

The following traffic policing settings have been configured on the edge device (Switch B) of the headquarters:

·     CIR of 10 Mbps for IP voice traffic.

·     CIR of 3 Mbps for business-specific application traffic.

·     CIR of 7 Mbps for FTP traffic.

Configure traffic shaping on the edge device (Switch A) of the branch to buffer excess traffic of each traffic type.

Configure rate limiting on Switch A to limit the outgoing traffic rate to 15 Mbps.

Figure 1 Network diagram

 

Analysis

To meet the network requirements, you must perform the following tasks:

·     To implement GTS, first determine the queue that transmits a type of traffic. In this example, the priorities of these types of traffic are not provided. You need to use priority marking to manually assign packets to different queues.

·     You can manually assign packets to queues by marking DSCP values, 802.1p priority values, or local precedence values. To keep the contents of packets unchanged, mark local precedence values for packets.

Applicable hardware and software versions

The following matrix shows the hardware and software versions to which this configuration example is applicable:

 

Hardware	Software version
S6520XE-HI switch series	Supported in Release 11xx
S5560X-EI switch series	Supported in Release 111x
S5500V2-EI switch series	Supported in Release 111x
MS4520V2-30F switch	Supported in Release 111x
S5560S-EI switch series S5560S-SI switch series	Supported in Release 612x
S5130S-HI switch series S5130S-EI switch series S5130S-SI switch series S5130S-LI switch series	Supported in Release 612x
S5120V2-SI switch series S5120V2-LI switch series	Supported in Release 612x
S3100V3-EI switch series S3100V3-SI switch series	Supported in Release 612x
S5110V2 switch series	Supported in Release 612x
S5110V2-SI switch series	Supported in Release 612x
S5000V3-EI switch series	Supported in Release 612x
S5000E-X switch series	Supported in Release 612x
WAS6000 switch series	Supported in Release 612x
E128C switch E152C switch E500C switch series E500D switch series	Supported in Release 612x
MS4520V2 switch series (except the MS4520V2-30F switch)	Supported in Release 612x
MS4320V2 switch series MS4300V2 switch series MS4320 switch series MS4200 switch series	Supported in Release 612x
WS5850-WiNet switch series	Supported in Release 612x
WS5820-WiNet switch series WS5810-WiNet switch series	Supported in Release 612x

 

Procedures

Before configuring GTS and rate limiting, make sure there is network connectivity between the branch and headquarters.

This section does not describe the configurations for enabling network connectivity.

Configuring priority marking

1.     Create three traffic classes to match the three traffic types:

# Configure basic IPv4 ACL 2000 to match IP voice traffic (traffic from subnet 192.168.3.0/24).

<SwitchA> system-view

[SwitchA] acl basic 2000

[SwitchA-acl-ipv4-basic-2000] rule permit source 192.168.3.0 0.0.0.255

[SwitchA-acl-ipv4-basic-2000] quit

# Create a class named voice, and use ACL 2000 as the match criterion.

[SwitchA] traffic classifier voice

[SwitchA-classifier-voice] if-match acl 2000

[SwitchA-classifier-voice] quit

# Configure basic IPv4 ACL 2001 to match application traffic (traffic from subnet 192.168.2.0/24).

[SwitchA] acl basic 2001

[SwitchA-acl-ipv4-basic-2001] rule permit source 192.168.2.0 0.0.0.255

[SwitchA-acl-ipv4-basic-2001] quit

# Create a class named service, and use ACL 2001 as the match criterion.

[SwitchA] traffic classifier service

[SwitchA-classifier-service] if-match acl 2001

[SwitchA-classifier-service] quit

# Configure advanced IPv4 ACL 3000 to match FTP traffic (traffic from subnet 192.168.1.0/24 and with destination port number 20).

[SwitchA] acl advanced 3000

[SwitchA-acl-ipv4-adv-3000] rule permit tcp destination-port eq 20 source 192.168.1.0 0.0.0.255

[SwitchA-acl-ipv4-adv-3000] quit

# Create a class named ftp, and use ACL 3000 as the match criterion.

[SwitchA] traffic classifier ftp

[SwitchA-classifier-ftp] if-match acl 3000

[SwitchA-classifier-ftp] quit

2.     Create three traffic behaviors:

# Create a behavior named voice, and configure the behavior to mark packets with local precedence 6 (corresponding to queue 6).

[SwitchA] traffic behavior voice

[SwitchA-behavior-voice] remark local-precedence 6

[SwitchA-behavior-voice] quit

# Create a behavior named service, and configure the behavior to mark packets with local precedence 4 (corresponding to queue 4).

[SwitchA] traffic behavior service

[SwitchA-behavior-service] remark local-precedence 4

[SwitchA-behavior-service] quit

# Create a behavior named ftp, and configure the behavior to mark packets with local precedence 2 (corresponding to queue 2).

[SwitchA] traffic behavior ftp

[SwitchA-behavior-ftp] remark local-precedence 2

[SwitchA-behavior-ftp] quit

3.     Configure and apply a QoS policy:

# Create a QoS policy named shaping, and associate the three classes with their respective behaviors in the QoS policy.

[SwitchA] qos policy shaping

[SwitchA-qospolicy-shaping] classifier voice behavior voice

[SwitchA-qospolicy-shaping] classifier service behavior service

[SwitchA-qospolicy-shaping] classifier ftp behavior ftp

[SwitchA-qospolicy-shaping] quit

# Apply the QoS policy shaping to the inbound direction of GigabitEthernet 1/0/2.

[SwitchA] interface gigabitethernet 1/0/2

[SwitchA-GigabitEthernet1/0/2] qos apply policy shaping inbound

[SwitchA-GigabitEthernet1/0/2] quit

Configuring GTS

# Configure GTS on GigabitEthernet 1/0/1 to set the CIR to 10 Mbps for queue 6 (IP voice traffic).

[SwitchA] interface gigabitethernet 1/0/1

[SwitchA-GigabitEthernet1/0/1] qos gts queue 6 cir 10240

# Configure GTS on GigabitEthernet 1/0/1 to set the CIR to 3 Mbps for queue 4 (application traffic).

[SwitchA-GigabitEthernet1/0/1] qos gts queue 4 cir 3072

# Configure GTS on GigabitEthernet 1/0/1 to set the CIR to 7 Mbps for queue 2 (FTP traffic).

[SwitchA-GigabitEthernet1/0/1] qos gts queue 2 cir 7168

Configuring rate limiting

# Configure rate limiting on GigabitEthernet 1/0/1 to set the CIR to 15 Mbps for outgoing traffic.

[SwitchA-GigabitEthernet1/0/1] qos lr outbound cir 15360

Verifying the configuration

# Verify the priority marking settings of GigabitEthernet 1/0/2.

<Sysname> display qos policy interface inbound

Interface: GigabitEthernet1/0/2                                           

  Direction: Inbound                                                            

  Policy: shaping                                                              

   Classifier: voice                                                           

     Operator: AND                                                              

     Rule(s) :                                                                 

      If-match acl 2000                                                        

     Behavior: voice                                                           

      Marking:                                                                 

        Remark local-precedence 6                                              

   Classifier: service                                                         

     Operator: AND                                                             

     Rule(s) :                                                                 

      If-match acl 2001                                                        

     Behavior: service                                                          

      Marking:                                                                 

        Remark local-precedence 4                                              

   Classifier: ftp                                                              

     Operator: AND                                                             

     Rule(s) :                                                                 

      If-match acl 3000                                                        

     Behavior: ftp                                                             

      Marking:                                                                 

        Remark local-precedence 2

# Verify the GTS settings on GigabitEthernet 1/0/1.

<Sysname> display qos gts interface                          

Interface: GigabitEthernet1/0/1                                               

 Rule: If-match queue 6                                                        

  CIR 10240 (kbps), CBS 640000 (Bytes)                                         

 Rule: If-match queue 4                                                        

  CIR 3072 (kbps), CBS 192000 (Bytes)                                          

 Rule: If-match queue 2                                                        

  CIR 7168 (kbps), CBS 448000 (Bytes)

# Verify the rate limiting settings on GigabitEthernet 1/0/1.

<Sysname> display qos lr interface                          

Interface: GigabitEthernet1/0/1                                              

Direction: Outbound                                                            

 CIR 15360 (kbps),  CBS 960000 (Bytes)

Configuration files

	IMPORTANT: The port link-mode bridge command is available only on the following switches: ·     S6520XE-HI switch series. ·     S5560X-EI switch series. ·     S5500V2-EI switch series. ·     MS4520V2-30F switch.

 

#

acl basic 2000

 rule 0 permit source 192.168.3.0 0.0.0.255

#

acl basic 2001

 rule 0 permit source 192.168.2.0 0.0.0.255

#

acl advanced 3000

 rule 0 permit tcp source 192.168.1.0 0.0.0.255 destination-port eq ftp-data

#

traffic classifier ftp operator and

 if-match acl 3000

#

traffic classifier service operator and

 if-match acl 2001

#

traffic classifier voice operator and

 if-match acl 2000

#

traffic behavior ftp

 remark local-precedence 2

#

traffic behavior service

 remark local-precedence 4

#

traffic behavior voice

 remark local-precedence 6   

#

qos policy shaping

 classifier voice behavior voice

 classifier service behavior service

 classifier ftp behavior ftp 

#

interface GigabitEthernet1/0/1

 port link-mode bridge

 qos lr outbound cir 15360 cbs 960000

 qos gts queue 6 cir 10240 cbs 640000                                          

 qos gts queue 4 cir 3072 cbs 192000                                           

 qos gts queue 2 cir 7168 cbs 448000                                           

#

interface GigabitEthernet1/0/2

 port link-mode bridge

 qos apply policy shaping inbound

#

return