Table of Contents

1 LLDP Configuration Commands· 1-1

LLDP Configuration Commands· 1-1

display lldp local-information· 1-1

display lldp neighbor-information· 1-5

display lldp statistics· 1-9

display lldp status· 1-11

display lldp tlv-config· 1-12

lldp admin-status· 1-14

lldp check-change-interval 1-15

lldp enable· 1-15

lldp fast-count 1-16

lldp hold-multiplier 1-16

lldp management-address-tlv 1-17

lldp notification remote-change enable· 1-17

lldp timer notification-interval 1-18

lldp timer reinit-delay· 1-18

lldp timer tx-delay· 1-19

lldp timer tx-interval 1-19

lldp tlv-enable· 1-20

 

 

 

LLDP Configuration Commands

display lldp local-information

Syntax

display lldp local-information [ global | interface interface-type interface-number ]

View

Any view

Parameters

global: Displays the global LLDP information.

interface interface-type interface-number: Specifies a port by its type and number.

Description

Use the display lldp local-information command to display the global LLDP information or the information contained in the LLDP TLVs to be sent to neighboring devices through a port.

If no keyword or argument is specified, this command displays all the LLDP information to be sent, including the global LLDP information and the LLDP information about the LLDP-enabled ports.

Examples

# Display all the LLDP information to be sent.

<Sysname> display lldp local-information

Global LLDP local-information:

  Chassis ID         : 000f-e255-0010

  System name        : H3C

  System description : H3C WX6103

  System capabilities supported : Repeater,Bridge,Router

  System capabilities enabled   : Repeater,Bridge,Router

 

  MED information

  Device class: Connectivity device

 

  HardwareRev               : B

  FirmwareRev               : 1.12

  SoftwareRev               : 5.20

  SerialNum                 : NONE

  Manufacturer name         : H3C

  Model name                : H3C EWPX1G24XA0

  Asset tracking identifier : Unknown

LLDP local-information of port 8[GigabitEthernet0/0/8]:

  Port ID subtype  : Interface name

  Port ID          : GigabitEthernet0/0/8

  Port description : GigabitEthernet0/0/8 Interface

 

  Management address type           : ipV4

  Management address                : 192.168.3.20

  Management address interface type : IfIndex

  Management address interface ID   : 55

  Management address OID            : 0

 

  Port VLAN ID(PVID): 10

 

  Port and protocol VLAN ID(PPVID) : 10

  Port and protocol VLAN supported : Yes

  Port and protocol VLAN enabled   : No

 

  VLAN name of VLAN 10: VLAN 0010

 

  Auto-negotiation supported : Yes

  Auto-negotiation enabled   : Yes

  OperMau                    : speed(1000)/duplex(Full)

 

  Power port class          : PSE

  PSE power supported       : Yes

  PSE power enabled         : No

  PSE pairs control ability : No

  Power pairs               : Signal

  Port power classification : Class 0

 

  Link aggregation supported : Yes

  Link aggregation enabled   : No

  Aggregation port ID        : 0

 

  Maximum frame Size: 9216

 

  MED information

  Media policy type        : Unknown

  Unknown Policy           : Yes

  VLAN tagged              : No

  Media policy VlanID      : 0

  Media policy L2 priority : 0

  Media policy Dscp        : 0

 

  PoE PSE power source      : Primary

  Port PSE Priority         : Low

  Port Available power value: 15.4(w)

Table 1-1 Description on the fields of the display lldp local-information command

Field	Description
Global LLDP local-information	The global LLDP information
Chassis ID	Device MAC address
System name	System name of the device
System description	System description
System capabilities supported	Supported capabilities, which can be: l      Bridge, indicating switching l      Router, indicating routing l      Repeater, indicating forwarding
System capabilities enabled	Currently enabled capabilities, which can be: l      Bridge, indicating switching is currently enabled. l      Router, indicating routing is currently enabled. l      Repeater, indicating forwarding is currently enabled.
PoE device type	PoE device type
MED information	MED information
Device class	MED device type
(MED inventory information of master board)	MED inventory information of the master board
HardwareRev	Hardware version
FirmwareRev	Firmware version
SoftwareRev	Software version
SerialNumber	Serial number
Manufacturer name	Device manufacturer
Model name	Device model
Asset tracking identifier	Asset tracking ID
LLDP local-information of port number interface-type interface-number	LLDP information about a port
Port ID subtype	Port ID type
Port ID	Port ID
Port description	Port description
Management address type	Management address type
Management address	Management address
Management address interface type	Type of the interface identified by the management address
Management address interface ID	ID of the interface identified by the management address
Management address OID	Management address object ID
Port VLAN ID(PVID)	Port VLAN ID
Port and protocol VLAN ID(PPVID)	Port protocol VLAN ID
Port and protocol VLAN supported	Indicates whether protocol VLAN is supported on the port.
Port and protocol VLAN enabled	Indicates whether protocol VLAN is enabled on the port.
VLAN name of VLAN ID	Name of the VLAN identified by the VLAN ID
Auto-negotiation supported	Indicates whether auto-negotiation is supported on the port.
Auto-negotiation enabled	State of auto-negotiation
OperMau	Current speed and duplex state of the port
Power port class	PoE device type, which can be : l      PSE, indicating a power supply device l      PD, indicating a powered device
PSE power supported	Indicates whether or not the device can operate as a PSE.
PSE power enabled	Indicates whether or not the device is operating as a PSE.
PSE pairs control ability	Indicates whether or not the PSE-PD pair control is available.
Power pairs	PoE mode, which can be Signal or Spare.
Port power classification	Port power classification of the PD, which can be: l      Class0 l      Class1 l      Class2 l      Class3 l      Class4
Link aggregation supported	Indicates whether or not link aggregation is supported.
Link aggregation enabled	Indicates whether or not link aggregation is enabled.
Aggregation port ID	Aggregation group ID, which is 0 if link aggregation is not enabled.
Maximum frame Size	Maximum frame size supported
MED information	MED LLDP information
Media policy type	Media policy type, which can be: l      Voice, indicating the device is capable of processing voice data. l      Unknown, indicating the media policy is unknown.
Unknown Policy	Indicates whether or not the media policy is unknown.
VLAN tagged	Indicates whether packets of the voice VLAN are tagged.
Media Policy VlanID	ID of the voice VLAN
Media Policy L2 priority	Layer 2 priority
Media Policy Dscp	DSCP precedence
Location format	Location format, which can be: l      Civic Address LCI, indicating normal address information. l      ECS ELIN, indicating telephone number for urgencies.
Location Information	Location information
PoE PSE power source	PSE type, which can be: l      Primary, indicating a primary power supply l      Backup, indicating a backup power supply
Port PSE Priority	Port PSE priority, which can be : l      Unknown l      Critical l      High l      Low
Port Available power value	PoE power

 

display lldp neighbor-information

Syntax

display lldp neighbor-information [ interface interface-type interface-number ] [ brief ]

View

Any view

Parameters

interface interface-type interface-number: Specifies a port by its type and number.

brief: Displays the LLDP information in brief.

Description

Use the display lldp neighbor-information command to display the LLDP information about the neighboring devices received through a port.

With no keyword/argument specified, this command displays the LLDP information received through all the ports.

Examples

# Display the LLDP information received through all the ports.

<Sysname> display lldp neighbor-information

LLDP neighbor-information of port 8[GigabitEthernet0/0/8]:

  Neighbor index   : 1

  Update time      : 0 days,5 hours,26 minutes,13 seconds

  Chassis type     : MAC address

  Chassis ID       : 000f-e211-bcef

  Port ID type     : Interface name

  Port ID          : GigabitEthernet0/0/8

  Port description : GigabitEthernet0/0/8 Interface

  System name        : H3C

  System description : H3C WX6103

  System capabilities supported : Repeater,Bridge,Router

  System capabilities enabled   : Repeater,Bridge,Router

 

  Management address type           : ipV4

  Management address                : 192.168.3.3

  Management address interface type : IfIndex

  Management address interface ID   : 56

  Management address OID            : 0

 

  Port VLAN ID(PVID): 10

 

  Port and protocol VLAN ID(PPVID) : 10

  Port and protocol VLAN supported : Yes

  Port and protocol VLAN enabled   : No

 

  VLAN name of VLAN 10: VLAN 0010

 

  Auto-negotiation supported : Yes

  Auto-negotiation enabled   : Yes

  OperMau                    : speed(1000)/duplex(Full)

 

  Power port class          : PD

  PSE power supported       : No

  PSE power enabled         : No

  PSE pairs control ability : No

  Power pairs               : Signal

  Port power classification : Class 0

 

  Link aggregation supported : Yes

  Link aggregation enabled   : No

  Aggregation port ID        : 0

 

  Maximum frame Size: 9216

 

LLDP neighbor-information of port 24[GigabitEthernet1/0/24]:

  Neighbor index   : 1

  Update time      : 0 days,5 hours,19 minutes,10 seconds

  Chassis type     : MAC address

  Chassis ID       : 000f-e233-5577

  Port ID type     : Interface name

  Port ID          : GigabitEthernet1/0/30

  Port description : GigabitEthernet1/0/30 Interface

  System name        : H3C

  System description : H3C WX6103

  System capabilities supported : Repeater,Bridge,Router

  System capabilities enabled   : Repeater,Bridge,Router

 

  Management address type           : ipV4

  Management address                : 192.168.0.151

  Management address interface type : IfIndex

  Management address interface ID   : 36

  Management address OID            : 0

 

  Port VLAN ID(PVID): 1

 

  Port and protocol VLAN ID(PPVID) : 1

  Port and protocol VLAN supported : Yes

  Port and protocol VLAN enabled   : No

 

  VLAN name of VLAN 1: VLAN 0001

 

  Auto-negotiation supported : Yes

  Auto-negotiation enabled   : Yes

  OperMau                    : speed(1000)/duplex(Full)

 

  Power port class          : PD

  PSE power supported       : No

  PSE power enabled         : No

  PSE pairs control ability : No

  Power pairs               : Signal

  Port power classification : Class 0

 

  Link aggregation supported : Yes

  Link aggregation enabled   : No

  Aggregation port ID        : 0

 

  Maximum frame Size: 9216

 

  Neighbor index   : 2

  Update time      : 0 days,5 hours,19 minutes,10 seconds

  Chassis type     : MAC address

  Chassis ID       : 000f-e200-6504

  Port ID type     : Interface name

  Port ID          : GigabitEthernet0/0/23

  Port description : GigabitEthernet0/0/23 Interface

  System name        : H3C

  System description : R&D Hangzhou, H3C Technology Co., Ltd.

  System capabilities supported : Repeater,Bridge,Router

  System capabilities enabled   : Repeater,Bridge,Router

 

  Management address type           : ipV4

  Management address                : 192.168.0.72

  Management address interface type : IfIndex

  Management address interface ID   : 51

  Management address OID            : 0

 

  Port VLAN ID(PVID): 1

 

  Port and protocol VLAN ID(PPVID) : 1

  Port and protocol VLAN supported : Yes

  Port and protocol VLAN enabled   : No

 

  VLAN name of VLAN 1: VLAN 0001

 

  Auto-negotiation supported : Yes

  Auto-negotiation enabled   : Yes

  OperMau                    : speed(100)/duplex(Full)

 

  Power port class          : PSE

  PSE power supported       : Yes

  PSE power enabled         : No

  PSE pairs control ability : No

  Power pairs               : Signal

  Port power classification : Class 0

 

  Link aggregation supported : Yes

  Link aggregation enabled   : No

  Aggregation port ID        : 0

 

  Maximum frame Size: 1536

Table 1-2 Description on the fields of the display lldp neighbor-information command

Field	Description
LLDP neighbor-information	LLDP information about a neighboring device
LLDP neighbor-information of Port number interface-type interface number	LLDP information received through a specific port
Neighbor index	Neighbor index
Update time	Time when the LLDP information about a neighboring device is latest updated.
Chassis type	Chassis information, which can be: l      Chassis component l      Interface alias l      Port component l      MAC address l      Network address l      Interface name l      Locally assigned (indicating the local configuration)
Chassis ID	Value of chassis type
Port ID type	Port information, which can be: l      Interface alias l      Port component l      MAC address l      Network Address l      Interface name l      Agent circuit ID l      Locally assigned (indicating the local configuration)
Port ID	Value of port ID type
Port description	Port description
System name	System name of the neighboring device
System description	System description of the neighboring device
System capabilities supported	Capabilities supported on the neighboring device, which can be: l      Bridge, indicating switching l      Router, indicating routing l      Repeater, indicating forwarding
System capabilities enabled	Capabilities currently enabled on the neighboring device, which can be: l      Bridge, indicating switching is currently enabled. l      Router, indicating routing is currently enabled. l      Repeater, indicating forwarding is currently enabled.
Management address type	Management address type
Management address	Management address
Management address interface type	Type of the interface identified by the management address
Management address interface ID	Management address interface ID
Management address OID	Management address object ID
Port VLAN ID	Port VLAN ID
Port and protocol VLAN ID(PPVID)	Port protocol VLAN ID
Port and protocol VLAN supported	Indicates whether protocol VLAN is supported.
Port and protocol VLAN enabled	Indicates whether protocol VLAN is enabled.
VLAN name of VLAN 1	Name of he port VLAN
Auto-negotiation supported	Indicates whether auto-negotiation is supported.
Auto-negotiation enabled	State of auto-negotiation
OperMau	Current speed and duplex state
Power port class	PoE device type, which can be: l      PSE, indicating a power supply device. l      PD, indicating a powered device.
PSE power supported	Indicates whether or not the device can operate as a PSE.
PSE power enabled	Indicates whether or not the device is operating as a PSE.
PSE pairs control ability	Indicates whether or not the PSE-PD pair control is available.
Power pairs	PoE mode, which can be Signal or Spare.
Port power classification	Port power classification of the PD, which can be the following: l      Class0 l      Class1 l      Class2 l      Class3 l      Class4
Link aggregation supported	Indicates whether or not link aggregation is supported.
Link aggregation enabled	Indicates whether or not link aggregation is enabled.
Aggregation port ID	Aggregation group ID, which is 0 if link aggregation is not enabled.
Maximum frame Size	Maximum frame size supported

 

display lldp statistics

Syntax

display lldp statistics [ global | interface interface-type interface-number ]

View

Any view

Parameters

global: Displays the global LLDP statistics.

interface interface-type interface-number: Specifies a port by its type and number.

Description

Use the display lldp statistics command to display the global LLDP statistics or the LLDP statistics of a port.

If no keyword/argument is specified, this command displays all the LLDP statistics.

Examples

# Display all the LLDP statistics.

<Sysname> display lldp statistics

lldp statistics global Information:

Neighbor information last change time:0 days,5 hours,26 minutes,13 seconds

The number of neighbor information inserted : 37

The number of neighbor information deleted  : 26

The number of neighbor information dropped  : 0

The number of neighbor information aged out : 4

 

lldp statistics Information of port 1 [GigabitEthernet0/0/1]:

The number of frames transmitted            : 5476

The number of frames received               : 26810

The number of frames discarded              : 0

The number of error frames                  : 0

The number of TLVs discarded                : 0

The number of TLVs unrecognized             : 0

The number of neighbor information aged out : 1

……

<Omitted>

Table 1-3 Description on the fields of the display lldp statistics command

Field	Description
lldp statistics global information	Global LLDP statistics
Neighbor information last change time	Time the neighbor information is latest updated
The number of neighbors inserted	Number of times of adding neighbor information
The number of neighbors deleted	Number of times of removing neighbor information
The number of neighbors dropped	Number of times of dropping neighbor information due to lack of available memory space
The number of neighbors aged out	Number of the neighbor information entries that have aged out
lldp statistics Information of port number interface-type interface-number	LLDP statistics of a port
The number of frames transmitted	Total number of the frames transmitted through the port
The number of frames received	Total number of the frames received through the port
The number of frames discarded	Total number of the frames dropped on the port
The number of error frames	Total number of the error frames on the port
The number of TLVs discarded	Total number of the TLVs dropped on the port
The number of TLVs unrecognized	Total number of the TLVs that cannot be recognized on the port
The number of neighbor information aged out	Number of the neighbor information entries that have aged out on the port

 

display lldp status

Syntax

display lldp status [ interface interface-type interface-number ]

View

Any view

Parameters

interface interface-type interface-number: Specifies a port by its type and number.

Description

Use the display lldp status command to display the LLDP status of a port.

If no port is specified, this command displays the LLDP status of all the ports.

Examples

# Display the LLDP status of all the ports.

<Sysname> display lldp status

Global status of LLDP: Enable

The current number of neighbors: 7

Neighbor information last changed time: 0 days,5 hours,26 minutes,13 seconds

Transmit interval              : 30s

Hold multiplier                : 4

Reinit delay                   : 2s

Transmit delay                 : 2s

Trap interval                  : 5s

Fast start times               : 3

 

Port 1 [GigabitEthernet0/0/1]:

Port status of LLDP            : Enable

Admin status                   : Tx_Rx

Trap flag                      : No

Roll time                      : 0s

Number of neighbors:             3

Number of MED neighbors        : 0

Number of sent optional TLV    : 22

Number of received unknown TLV : 0

……

<Omitted>

Table 1-4 Description on the fields of the display lldp status command

Field	Description
Global status of LLDP	Indicating whether or not LLDP is globally enabled
The current number of neighbors	Total number of the neighbor devices
Neighbor information last changed time	Time when the neighbor information is latest updated
Transmit interval	Interval to send LLDPDU
Hold multiplier	TTL multiplier
Reinit delay	Initialization delay
Transmit delay	Delay period to send LLDPDUs
Trap interval	Interval to send traps
Fast start times	Number of the LLDPDUs to be sent successively when a new neighboring device is detected
Port number interface-type interface-number	Port LLDP status
Port status of LLDP	Indicates whether or not LLDP is enabled on the port.
Admin status	LLDP mode of the port, which can be: l      TxRx. A port in this mode sends and receives LLDPDUs. l      Rx_Only. A port in this mode receives LLDPDUs only. l      Tx_Only. A port in this mode sends LLDPDUs only. l      Disable. A port in this mode does not send or receive LLDPDUs.
Trap Flag	Indicates whether or not trap is enabled.
Roll time	LLDP polling interval. A value of 0 indicates LLDP polling is disabled.
Number of neighbors	Number of the neighbors connecting to the port
Number of MED neighbors	Number of the MED neighbors connecting to the port
Number of sent optional TLV	Number of the optional TLVs contained in an LLDPDU sent through the port
Number of received unknown TLV	Number of the unknown TLVs contained in a received LLDPDU

 

display lldp tlv-config

Syntax

display lldp tlv-config [ interface interface-type interface-number ]

View

Any view

Parameters

interface interface-type interface-number: Specifies a port by its type and number.

Description

Use the display lldp tlv-config command to display the TLVs that are currently sent through a port.

If no port is specified, this command displays all the TLVs that are currently sent through all the ports.

Examples

# Display all the TLVs that are currently sent through all the ports.

<Sysname> display lldp tlv-config

LLDP tlv-config of port 1[GigabitEthernet0/0/1]:

NAME                              STATUS    DEFAULT

Basic optional TLV:

Port Description TLV              YES       YES

System Name TLV                   YES       YES

System Description TLV            YES       YES

System Capabilities TLV           YES       YES

Management Address TLV            YES       YES

 

IEEE 802.1 extend TLV:

Port VLAN ID TLV                  YES       YES

Port And Protocol VLAN ID TLV     YES       YES

VLAN Name TLV                     YES       YES

 

IEEE 802.3 extend TLV:

MAC-Physic TLV                    YES       YES

Power via MDI TLV                 YES       YES

Link Aggregation TLV              YES       YES

Maximum Frame Size TLV            YES       YES

 

LLDP-MED extend TLV:

Capabilities TLV                  YES       YES

Network Policy TLV                YES       YES

Location Identification TLV       NO        NO

Extended Power via MDI TLV        YES       YES

Inventory TLV                     YES       YES  

……

<Omitted>

Table 1-5 Description on the fields of the display lldp tlv-config command

Field	Description
LLDP tlv-config of port number interface-type interface-number	TLVs that are currently sent through a port
NAME	TLV type
STATUS	Indicates whether or not TLVs of a specific type are currently sent through a port
DEFAULT	Indicates whether or not TLVs of a specific type are sent through a port by default
Basic optional TLV	Basic TLVs, including: l      Port description TLV l      System name TLV l      System description TLV l      System capabilities TLV l      Management address TLV
IEEE 802.1 extend TLV	IEEE 802.1 extended TLVs, including: l      Port VLAN ID TLV l      Port and protocol VLAN ID TLV l      VLAN name TLV
IEEE 802.3 extend TLV	IEEE 802.3 extended TLVs, including: l      MAC-Physic TLV l      Power via MDI TLV l      Link aggregation TLV l      Maximum frame size TLV
LLDP-MED extend TLV	MED related LLDP TLVs, including: l      Capabilities TLV l      Network Policy TLV l      Extended Power-via-MDI TLV l      Location Identification TLV l      Inventory TLV, which can be hardware revision TLV, firmware revision TLV, software revision TLV, serial number TLV, manufacturer name TLV, model name TLV, and asset id TLV.

 

lldp admin-status

Syntax

lldp admin-status { disable | rx | tx | txrx }

undo lldp admin-status

View

Ethernet interface view, port group view

Parameters

disable: Specifies the Disable mode. A port in this mode does not send or receive LLDPDUs.

rx: Specifies the Rx mode. A port in this mode receives LLDPDUs only.

tx: Specifies the Tx mode. A port in this mode sends LLDPDUs only.

txrx: Specifies the TxRx mode. A port in this mode sends and receives LLDPDUs.

Description

Use the lldp admin-status command to specify the LLDP operating mode for a port or all the ports in a port group.

Use the undo lldp admin-status command to restore the default LLDP operating mode.

The default LLDP operating mode is TxRx.

Examples

# Configure the LLDP operating mode as Rx for GigabitEthernet 0/0/3.

<Sysname> system-view

[Sysname] interface GigabitEthernet 0/0/3

[Sysname-GigabitEthernet0/0/3] lldp admin-status rx

lldp check-change-interval

Syntax

lldp check-change-interval value

undo lldp check-change-interval

View

Ethernet interface view, port group view

Parameters

value: LLDP polling interval to be set, in the range 1 to 30 (in seconds).

Description

Use the lldp check-change-interval command to enable LLDP polling and set the polling interval.

Use the undo lldp check-change-interval command to restore the default.

By default, LLDP polling is disabled.

With LLDP polling enabled, LLDP detects for local configuration changes periodically. A local configuration change triggers LLDPDU sending, through which neighboring devices can be informed of the configuration change timely.

Examples

# Enable LLDP polling on GigabitEthernet 0/0/3, setting the polling interval to 30 seconds.

<Sysname> system-view

[Sysname] interface GigabitEthernet 0/0/3

[Sysname-GigabitEthernet0/0/3] lldp check-change-interval 30

lldp enable

Syntax

lldp enable

undo lldp enable

View

System view, Ethernet interface view, port group view

Parameters

None

Description

Use the lldp enable command to enable LLDP.

Use the undo lldp enable command to disable LLDP.

By default, LLDP is enabled on a port. Whether LLDP is enabled globally varies with device models.

Note that LLDP takes effect on a port only when it is enabled both globally and on the port.

Examples

# Disable LLDP on GigabitEthernet 0/0/3.

<Sysname> system-view

[Sysname] interface GigabitEthernet 0/0/3

[Sysname-GigabitEthernet0/0/3] undo lldp enable

lldp fast-count

Syntax

lldp fast-count value

undo lldp fast-count

View

System view

Parameters

value: Number of the LLDPDUs to be sent successively when a new neighboring device is detected. This argument ranges from 1 to 10.

Description

Use the lldp fast-count command to set the number of the LLDPDUs to be sent successively when a new neighboring device is detected.

Use the undo lldp fast-count command to restore the default.

By default, the number is 3.

Examples

# Configure to send four LLDP successively when a new neighboring device is detected.

<Sysname> system-view

[Sysname] lldp fast-count 4

lldp hold-multiplier

Syntax

lldp hold-multiplier value

undo lldp hold-multiplier

View

System view

Parameters

value: TTL multiplier, in the range 2 to 10.

Description

Use the lldp hold-multiplier command to set the TTL multiplier.

Use the undo lldp hold-multiplier command to restore the default.

The TTL multiplier defaults to 4.

You can set the TTL of the local device information by configuring the TTL multiplier.

The TTL of the information about a device is determined by the following expression:

TTL multiplier × LLDPDU sending interval.

You can set the TTL of the local device information by configuring the TTL multiplier. Note that the TTL can be up to 65535 seconds. TTLs longer than it will be rounded off to 65535 seconds.

To enable local device information to be updated on neighboring devices before being aged out, make sure the interval to send LLDPDUs is shorter than the TTL of the local device information.

Examples

# Set the TTL multiplier to 6.

<Sysname> system-view

[Sysname] lldp hold-multiplier 6

lldp management-address-tlv

Syntax

lldp management-address-tlv [ ip-address ]

undo lldp management-address-tlv

View

Ethernet interface view, port group view

Parameters

ip-address: Management address to be set.

Description

Use the lldp management-address-tlv command to enable the management address sending. This command also sets the management address.

Use the undo lldp management-address-tlv command to disable management address sending.

By default, the management address is sent through LLDPDUs, and the management address is the primary IP address of the VLAN with the least VLAN ID among the VLANs whose packets are permitted on the port. If the primary IP address is not configured, the management address is 127.0.0.1. For information about VLAN, refer to VLAN in H3C WX6103 Access Controller Switch Interface Board Configuration Guide.

Note that an LLDPDU carries only one management address. If you set the management address repeatedly, the latest one takes effect.

Examples

# Set the management address to 192.6.0.1 for GigabitEthernet 0/0/3.

<Sysname> system-view

[Sysname] interface GigabitEthernet 0/0/3

[Sysname-GigabitEthernet0/0/3] lldp management-address-tlv 192.6.0.1

lldp notification remote-change enable

Syntax

lldp notification remote-change enable

undo lldp notification remote-change enable

View

Ethernet interface view, port group view

Parameters

None

Description

Use the lldp notification remote-change enable command to enable trap for a port or all the ports in a port group.

Use the undo lldp notification remote-change enable command to restore the default.

By default, trap is disabled on a port.

Examples

# Enable trap for GigabitEthernet 0/0/3.

<Sysname> system-view

[Sysname] interface GigabitEthernet 0/0/3

[Sysname-GigabitEthernet0/0/3] lldp notification remote-change enable

lldp timer notification-interval

Syntax

lldp timer notification-interval value

undo lldp timer notification-interval

View

System view

Parameters

value: Interval to send trap messages, in the range 5 to 3600 (in seconds).

Description

Use the lldp timer notification-interval command to set the interval to send trap messages.

Use the undo lldp timer notification-interval command to restore the default.

By default, the interval to send trap messages is 5 seconds.

Examples

# Set the interval to send trap messages to 8 seconds.

<Sysname> system-view

[Sysname] lldp timer notification-interval 8

lldp timer reinit-delay

Syntax

lldp timer reinit-delay value

undo lldp timer reinit-delay

View

System view

Parameters

value: Initialization delay period to be set, in the range 1 to 10 (in seconds).

Description

Use the lldp timer reinit-delay command to set the initialization delay period.

Use the undo lldp timer reinit-delay command to restore the default.

By default, the initialization delay period is 2 seconds.

Examples

# Set the initialization delay period to 4 seconds.

<Sysname> system-view

[Sysname] lldp timer reinit-delay 4

lldp timer tx-delay

Syntax

lldp timer tx-delay value

undo lldp timer tx-delay

View

System view

Parameters

value: Delay period to send LLDPDUs, in the range 1 to 8192 (in seconds).

Description

Use the lldp timer tx-delay command to set the delay period to send LLDPDUs.

Use the undo lldp timer tx-delay command to restore the default.

By default, the delay period to send LLDPDUs is 2 seconds.

Examples

# Set the delay period to send LLDPDUs to 4 seconds.

<Sysname> system-view

[Sysname] lldp timer tx-delay 4

lldp timer tx-interval

Syntax

lldp timer tx-interval value

undo lldp timer tx-interval

View

System view

Parameters

value: Interval to send LLDPDUs, in the range 5 to 32768 (in seconds).

Description

Use the lldp timer tx-interval command to set the interval to send LLDPDUs.

Use the undo lldp timer tx-interval command to restore the default.

By default, the interval to send LLDPDUs is 30seconds.

To enable local device information to be updated on neighboring devices before being aged out, make sure the interval to send LLDPDUs is shorter than the TTL of the local device information.

Examples

# Set the interval to send LLDPDUs to 20 seconds.

<Sysname> system-view

[Sysname] lldp timer tx-interval 20

lldp tlv-enable

Syntax

lldp tlv-enable { basic-tlv { all | port-description | system-capability | system-description | system-name } | dot1-tlv { all | port-vlan-id | protocol-vlan-id [ vlan-id ] | vlan-name [ vlan-id ] } | dot3-tlv { all | link-aggregation | mac-physic | max-frame-size | power } | med-tlv { all | capability | location-id { civic-address device-type country-code { ca-type ca-value }&<1-10> | elin-address Tel-Number } | network-policy | power-over-ethernet | inventory } }

undo lldp tlv-enable { basic-tlv { all | port-description | system-capability | system-description | system-name } | dot1-tlv { all | port-vlan-id | protocol-vlan-id | vlan-name } | dot3-tlv { all | link-aggregation | mac-physic | max-frame-size | power } | med-tlv { all | capability | location-id | network-policy | power-over-ethernet | inventory } }

View

Ethernet interface view, port group view

Parameters

all: Sends all the basic LLDP TLVs, all the IEEE 802.1 defined LLDP TLVs, or all the IEEE 802.3 defined LLDP TLVs; or sends all the MED related LLDP TLVs except location identification TLVs.

basic-tlv: Sends basic LLDP TLVs.

port-description: Sends port description TLVs.

system-capability: Sends system capabilities TLVs.

system-description: Sends system description TLVs.

system-name: Sends system name TLVs.

dot1-tlv: Sends IEEE 802.1 defined LLDP TLVs.

port-vlan-id: Sends port VLAN ID TLVs.

protocol-vlan-id: Sends port and protocol VLAN ID TLVs.

vlan-name: Sends VLAN name TLVs.

vlan-id: ID of the VLAN the TLVs (port and protocol VLAN ID TLVs or VLAN name TLVs) concerning which are to be sent. This argument defaults to the least protocol VLAN ID.

dot3-tlv: Sends IEEE 802.3 defined LLDP TLVs.

link-aggregation: Sends link aggregation group TLVs.

mac-physic: Sends MAC/PHY configuration/status TLVs.

max-frame-size: Sends maximum frame size TLVS.

power: Sends power via MDI TLVs.

med-tlv: Sends MED related LLDP TLVs.

capability: Sends LLDP-MED capabilities TLVs.

location-id: Sends location identification TLVS.

civic-address: Inserts the address information about the intermediate device in location identification TLVs .

device-type: Device type value. A value of 0 specifies DHCP server; a value of 1 specifies switch, and a value of 2 specifies LLDP-MED endpoint.

country-code: Country code, confirming to ISO 3166.

ca-type: Location information type, in the range 0 to 255.

ca-value: Location information, a string of 1 to 255 characters.

elin-address: Inserts telephone numbers for urgencies in location identification TLVs.

Tel-Number: Telephone number for urgencies, a string of 10 to 25 characters.

network-policy: Sends network policy TLVs.

power-over-ethernet: Sends extended power-via-MDI TLVs.

inventory: Sends hardware revision TLVs, firmware revision TLVs, software revision TLVs, serial number TLVs, manufacturer name TLVs, model name TLVs, and asset ID TLVs.

Description

Use the lldp tlv-enable command to enable the sending of specific TLVs for a port or all the ports in a port group.

Use the undo lldp tlv-enable command to disable the sending of specific TLVs.

By default, all the TLVs except location identification TLVs are sent.

Note that:

l          To enable MED related LLDP TLV sending, you need to enable LLDP-MED capabilities TLV sending first. Conversely, to disable LLDP-MED capabilities TLV sending, you need to disable the sending of other MED related LLDP TLV.

l          To disable MAC/PHY configuration/status TLV sending, you need to disable LLDP-MED capabilities TLV sending first.

l          Specifying the all keyword for basic LLDP TLVs and organization defined LLDP TLVs (including IEEE 802.1 defined LLDP TLVs and IEEE 802.3 defined LLDP TLVs) enables sending of all the corresponding LLDP TLVs. For MED related LLDP TLVs, the all keyword enables sending of all the MED related LLDP TLVs except location identification TLVs.

l          Enabling the sending of LLDP-MED capabilities TLVs also enables the sending of MAC/PHY configuration/status TLVs.

l          You can specify to send multiple types of TLVs by executing the lldp tlv-enable command repeatedly.

Examples

# Enable the sending of link aggregation group TLVs on GigabitEthernet 0/0/3.

<Sysname> system-view

[Sysname] interface GigabitEthernet 0/0/3

[Sysname-GigabitEthernet0/0/3] lldp tlv-enable dot3-tlv link-aggregation