# With devices A and B connected to the outside AS, configure B with a default local preference of 180 in BGP-VPNv4 subaddress family view, allowing the route going through B to be preferred when more than one route is present.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] default local-preference 180

1.1.4 default med (BGP-VPNv4 subaddress family view)

Syntax

default med med-value

undo default med

View

BGP-VPNv4 subaddress family view

Default Level

2: System level

Parameters

med-value: MED value.

Description

Use the default med command to set the default system metric.

Use the undo default med command to restore the default.

With other criteria the same, the system selects the route with a smaller MED value as the AS external route.

By default, the MED value is 0.

Examples

# Set the default MED to 10 for PE1 in BGP-VPNv4 subaddress family view.

<Sysname> system-view

[Sysname] bgp 100

[Sysname] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] default med 10

1.1.5 description (VPN instance view)

Syntax

description text

undo description

View

VPN instance view

Default Level

2: System level

Parameters

text: Description for the VPN instance.

Description

Use the description command to configure a description for a VPN instance.

Use the undo description command to delete the description.

Examples

# Configure the description of VPN instance vpn1.

<Sysname> system-view

[Sysname] ip vpn-instance vpn1

[Sysname-vpn-instance-vpn1] description This is vpn1

1.1.6 display bgp vpnv4 all routing-table

Syntax

display bgp vpnv4 all routing-table [ network-address [ { mask | mask-length } [ longer-prefixes ] ] | as-path-acl as-path-acl-number | cidr | community [ aa:nn ]&<1-13> [ no-export-subconfed | no-advertise | no-export ]* [ whole-match ] | community-list { basic-community-list-number [ whole-match ] | adv-community-list-number }&<1-16> | different-origin-as | peer ip-address { advertised-routes | received-routes } [ statistic ] | regular-expression as-regular-expression | statistic ]

View

Any view

Default Level

1: Monitor level

Parameters

network-address: IP address of the destination segment.

mask: Network mask.

mask-length: Length of the network mask.

longer-prefixes: Specifies to match the longest prefix.

as-path-acl as-path-acl-number: Filters routing information using the specified AS_PATH list.

cidr: Displays classless inter-domain routing (CIDR) information.

community: Displays routing information of the specified BGP community in the routing table.

aa:nn&<1-13>: Community number. &<1-13> means that you can enter the parameter combination up to 13 times.

no-export-subconfed: A route with this attribute is neither advertised out of the local AS, nor advertised to the other sub-ASs in the confederation.

no-advertise: A route with this attribute is not advertised to any other BGP peer.

no-export: A route with this attribute is not advertised out of the local AS or, If existing, confederation. However, it is advertised to the other sub-ASs in the confederation.

whole-match: Performs exact match.

community-list: Displays routing information of the specified BGP community list in the routing table.

basic-community-list-number: Basic community list number, in the range 1 to 99.

adv-community-list-number: Advanced community list number, in the range 100 to 199.

&<1-16>: Specifies that the argument before it can be entered up to 16 times.

different-origin-as: Displays information about routes with different AS origins.

peer ip-address: Specifies a BGP VPNv4 peer by its IP address.

advertised-routes: Specifies the routing information advertised to the specified peer.

received-routes: Specifies the routing information received from the specified peer.

regular-expression as-regular-expression: Displays routing information matching the specified AS_PATH regular expression.

statistic: Displays BGP VPNv4 route statistics.

Description

Use the display bgp vpnv4 all routing-table command to display all BGP VPNv4 routing information.

Examples

# Display all BGP VPNv4 routing information.

<Sysname> display bgp vpnv4 all routing-table

BGP Local router ID is 2.2.2.2

Status codes: * - valid, > - best, d - damped,

h - history, i - internal, s - suppressed, S - Stale

Origin : i - IGP, e - EGP, ? - incomplete

Total number of routes from all PE: 2

Route Distinguisher: 100:1

Network NextHop Label(recv/app) MED LocPrf

*>i 10.0.0.0 1.1.1.1 (1025 /NULL ) 0 100

*>i 123.1.1.1/32 1.1.1.1 (1024 /NULL ) 0 100

Total routes of vpn-instance vpn1: 5

Network NextHop Label(recv/app) MED LocPrf

*>i 10.0.0.0 1.1.1.1 0 100

*> 10.1.1.0/24 0.0.0.0 (NULL /1025 ) 0

*> 20.0.0.0 10.1.1.1 (NULL /1026 ) 0

*>i 123.1.1.1/32 1.1.1.1 0 100

*> 124.1.1.1/32 0.0.0.0 (NULL /1024 ) 0

Table 1-1 Description on the fields of display bgp vpnv4 all routing-table

Field	Description
BGP Local router ID	Router ID of the local BGP device
Status codes	Route status codes. Valid values include: * - valid: Valid route > - best: Best route d - damped: Route damped for route flap h - history: History route i - internal: Internal route s - suppressed: Suppressed route S - Stale: Stale route
Origin	Route origin codes. Valid values include: i - IGP (learned from the AS) e - EGP (learned through EGP) ? - incomplete (learned in any other way)
Total number of routes from all PE	Total number of VPNv4 routes from all PEs
Route Distinguisher	RD
Network	Network address
NextHop	Address of the next hop
Label(recv/app)	Incoming and outgoing labels
MED	Metric associated with the destination network
Total routes of vpn-instance vpn1	Total number of routes of the specified VPN instance
LocPrf	Local preference

1.1.7 display bgp vpnv4 group

Syntax

display bgp vpnv4 { all | vpn-instance vpn-instance-name } group [ group-name ]

View

Any view

Default Level

1: Monitor level

Parameters

all: Specifies all VPNv4 peers.

vpn-instance-name: Name of the VPN instance.

group-name: Name of the BGP peer group.

Description

Use the display bgp vpnv4 group command to display information about a specified or all BGP VPNv4 peer groups.

Examples

# Display information about BGP VPNv4 peer group a for VPN instance vpn1.

<Sysname> display bgp vpnv4 vpn-instance vpn1 group a

BGP peer-group is a

remote AS 200

Type : external

Maximum allowed prefix number: 150000

Threshold: 75%

Configured hold timer value: 180

Keepalive timer value: 60

Minimum time between advertisement runs is 30 seconds

Peer Preferred Value: 99

No routing policy is configured

Members:

Peer V AS MsgRcvd MsgSent OutQ PrefRcv Up/Down State

10.1.1.1 4 200 18 21 0 1 00:12:58 Established

Table 1-2 Description on the fields of the display bgp vpnv4 group command

Field	Description
BGP peer-group	Name of the BGP peer group
remote AS number	Number of the remote AS
Type	Type of the BGP peer group
Maximum allowed prefix number	Maximum number of routes that the VPN instance supports
Threshold	Threshold value
Configured hold timer value	Setting of the hold timer
Keepalive timer value	Keepalive interval
Minimum time between advertisement runs	Minimum route advertisement interval
Peer Preferred Value	Weight for the routes from the peer
No routing policy is configured	Whether the VPN instance is configured with a routing policy
Peer	IP address of the peer
V	Version of BGP that the peer runs
AS	AS number of the peer group
MsgRcvd	Number of messages received
MsgSent	Number of messages sent
OutQ	Number of messages waiting to be sent to the peer
PrefRcv	Number of prefixes received
Up/Down	Duration of the BGP session in the current state
State	Status of the peer

1.1.8 display bgp vpnv4 network

Syntax

display bgp vpnv4 { all | vpn-instance vpn-instance-name } network

View

Any view

Default Level

1: Monitor level

Parameters

all: Specifies all VPNv4 peers.

vpn-instance-name: Name of the VPN instance.

Description

Use the display bgp vpnv4 network command to display information about BGP VPNv4 routes injected into a specified or all VPN instances.

Examples

# Display information about BGP VPNv4 routes injected into VPN instance vpn1.

<Sysname> display bgp vpnv4 vpn-instance vpn1 network

BGP Local Router ID is 1.1.1.1.

Local AS Number is 100.

Network Mask Route-policy

10.0.0.0 255.0.0.0

Table 1-3 Description on the fields of the display bgp vpnv4 network command

Field	Description
BGP Local Router ID	Router ID of the local BGP router
Local AS Number	Number of the local AS
Network	Advertised network route
Mask	Mask of the advertised network route
Route-policy	Routing policy configured

1.1.9 display bgp vpnv4 paths

Syntax

display bgp vpnv4 { all | vpn-instance vpn-instance-name } paths [ as-regular-expression ]

View

Any view

Default Level

1: Monitor level

Parameters

all: Specifies all VPNv4 peers.

vpn-instance-name: Name of the VPN instance.

as-regular-expression: Regular expression for filtering the AS path information to be displayed.

Description

Use the display bgp vpnv4 paths command to display the BGP VPNv4 AS path information.

Examples

# Display the BGP VPNv4 AS path information of VPN instance vpn1.

<Sysname> display bgp vpnv4 vpn-instance vpn1 paths

Address Hash Refcount MED Path/Origin

0x6E72D18 0 1 0 200?

0x6E72E50 0 1 0 i

0x6E72B78 1 1 0 ?

0x6E72BE0 1 2 0 ?

# Display all BGP VPNv4 AS path information.

<Sysname> display bgp vpnv4 all paths

Address Hash Refcount MED Path/Origin

0x6E72D80 4 1 0 200?

0x6E72CB0 15 2 0 ?

Table 1-4 Description on the fields of the display bgp vpnv4 paths command

Field	Description
Address	Routing address in the local database
Hash	Hash bucket for storing routes
Refcount	Number of times that the path is referenced
MED	Metric for routes
Path/Origin	AS_PATH and origin attributes of the route, see Table 1-1.

1.1.10 display bgp vpnv4 peer

Syntax

display bgp vpnv4 { all | vpn-instance vpn-instance-name } peer [ group-name log-info | ip-address { log-info | verbose } | verbose ]

View

Any view

Default Level

1: Monitor level

Parameters

all: Specifies all VPNv4 peers.

vpn-instance-name: Name of the VPN instance.

group-name: Name of the peer group.

log-info: Displays log information.

ip-address: IP address of the peer.

verbose: Displays detailed information.

Description

Use the display bgp vpnv4 peer command to display information about BGP VPNv4 peers.

Examples

# Display information about BGP VPNv4 peers of VPN instance vpn1.

<Sysname> display bgp vpnv4 vpn-instance vpn1 peer

BGP local router ID : 2.2.2.2

Local AS number : 100

Total number of peers : 1 Peers in established state : 1

Peer V AS MsgRcvd MsgSent OutQ PrefRcv Up/Down State

10.1.1.1 4 200 24 29 0 1 00:18:47 Established

Table 1-5 Description on the fields of display bgp vpnv4 vpn-instance peer

Field	Description
BGP Local router ID	Router ID of the local BGP device
local AS number	Local AS number
Total number of peers	Total number of peers
Peers in established state	Number of peers in the state of established
Peer	IP address of the peer
V	Version of BGP that the peer runs
AS	AS number of the peer group
MsgRcvd	Number of messages received
MsgSent	Number of messages sent
OutQ	Number of messages waiting to be sent to the peer
PrefRcv	Number of received prefixes
Up/Down	Duration of the BGP session in the current state
State	Status of the peer

# Display detailed information about BGP VPNv4 peers of VPN instance vpn1.

<Sysname> display bgp vpnv4 vpn-instance vpn1 peer verbose

Peer: 10.1.1.1 Local: 2.2.2.2

Type: EBGP link

BGP version 4, remote router ID 10.1.1.1

BGP current state: Established, Up for 00h19m26s

BGP current event: KATimerExpired

BGP last state: OpenConfirm

Port: Local - 179 Remote - 1025

Configured: Active Hold Time: 180 sec Keepalive Time:60 sec

Received : Active Hold Time: 180 sec

Negotiated: Active Hold Time: 180 sec Keepalive Time:60 sec

Peer optional capabilities:

Peer support bgp multi-protocol extended

Peer support bgp route refresh capability

Address family IPv4 Unicast: advertised and received

Received: Total 25 messages, Update messages 1

Sent: Total 30 messages, Update messages 4

Maximum allowed prefix number: 150000

Threshold: 75%

Minimum time between advertisement runs is 30 seconds

Optional capabilities:

Route refresh capability has been enabled

Peer Preferred Value: 99

Routing policy configured:

No routing policy is configured

Table 1-6 Description on the fields of the display bgp vpnv4 peer verbose command

Field	Description
Peer	IP address of the peer
Local	IP address of the local device
Type	BGP type
BGP version	Version of BGP that the peer runs
remote router ID	Router ID of the remote device
BGP current state	Current status of the BGP session
Up for	Duration since the peer is established
BGP current event	Current event of the BGP session
BGP last state	State that the BGP session was in before transitioning to the current status
Port	Local and remote ports of the BGP session
Configured	Settings of the local timers, including the active hold interval and keepalive interval
Received	Received active hold interval
Negotiated	Negotiated active hold interval
Peer optional capabilities	Optional capabilities of the peer
Peer support bgp multi-protocol extended	The peer supports multiprotocol extension.
Peer support bgp route refresh capability	The peer supports route refresh capability.
Address family IPv4 Unicast	IPv4 unicast family capability
Received	Total number of received messages and the number of received update messages
Sent	Total number of sent messages and the number of sent update messages
Maximum allowed prefix number	Maximum number of routes that the VPN instance supports
Threshold	Threshold value
Minimum time between advertisement runs	Minimum route advertisement interval
Optional capabilities	Local optional capabilities
Route refresh capability has been enabled	Whether the route refresh capability is supported
Peer Preferred Value	Weight for the routes from the peer
Routing policy configured	Routing policy configured

# Display all BGP VPNv4 peer information.

<Sysname> display bgp vpnv4 all peer

BGP local router ID : 2.2.2.2

Local AS number : 100

Total number of peers : 1 Peers in established state : 1

Peer V AS MsgRcvd MsgSent OutQ PrefRcv Up/Down State

1.1.1.1 4 100 51 64 0 2 00:45:16 Established

Table 1-7 Description on the fields of the display bgp vpnv4 all peer command

Field	Description
Peer	IP address of the peer
V	Version of BGP that the peer runs
AS	AS number
MsgRcvd	Number of messages received
MsgSent	Number of messages sent
OutQ	Number of messages waiting to be sent to the peer
Up/Down	Duration of the BGP session in the current state
State	Status of the peer

# Display detailed information about BGP VPNv4 peer 1.1.1.1.

<Sysname> display bgp vpnv4 all peer 1.1.1.1 verbose

Peer: 1.1.1.1 Local: 2.2.2.2

Type: IBGP link

BGP version 4, remote router ID 1.1.1.1

BGP current state: Established, Up for 00h46m01s

BGP current event: RecvKeepalive

BGP last state: OpenConfirm

Port: Local - 1039 Remote - 179

Configured: Active Hold Time: 180 sec Keepalive Time:60 sec

Received : Active Hold Time: 180 sec

Negotiated: Active Hold Time: 180 sec Keepalive Time:60 sec

Peer optional capabilities:

Peer support bgp multi-protocol extended

Peer support bgp route refresh capability

Address family IPv4 Unicast: advertised and received

Address family VPNv4: advertised and received

Received: Total 52 messages, Update messages 2

Sent: Total 65 messages, Update messages 5

Maximum allowed prefix number: 150000

Threshold: 75%

Minimum time between advertisement runs is 15 seconds

Optional capabilities:

Route refresh capability has been enabled

Connect-interface has been configured

Peer Preferred Value: 0

Routing policy configured:

No routing policy is configured

Table 1-8 Description on the fields of display bgp vpnv4 all peer verbose

Field	Description
Peer	IP address of the peer
Local	IP address of the local device
Type	BGP type
BGP version	Version of BGP that the peer runs
remote router ID	Router ID of the remote device
BGP current state	Current status of the BGP session
Up for	Duration since the peer is established
BGP current event	Current event of the peer
BGP last state	State that the BGP session was in before transitioning to the current status
Port	Local and remote BGP port numbers
Configured	Settings of the local timers, including the active hold interval and keepalive interval
Received	Received active hold interval
Negotiated	Negotiated active hold interval
Peer optional capabilities	Optional capabilities of the peer
Peer support bgp multi-protocol extended	The peer supports multiprotocol extension.
Peer support bgp route refresh capability	The peer supports route refresh capability.
Address family IPv4 Unicast	IPv4 unicast family capability
Address family VPNv4	IPv4 address group VPNv4 capability
Received	Counts of received messages
Sent	Counts of sent messages
Maximum allowed prefix number	Maximum number of routes that the VPN instance supports
Threshold	Threshold value
Minimum time between advertisement runs	Minimum route advertisement interval
Optional capabilities	Local optional capabilities
Route refresh capability	Whether the route refresh capability is supported
Connect-interface	Whether a source interface is configured for route update messages
Peer Preferred Value	Weight configured for routes from the peer
Routing policy configured	Routing policy configured

1.1.11 display bgp vpnv4 route-distinguisher routing-table

Syntax

display bgp vpnv4 route-distinguisher route-distinguisher routing-table [ network-address [ { mask | mask-length } [ longer-prefixes ] ] | as-path-acl as-path-acl-number | cidr | community [ aa:nn ]&<1-13> [ no-export-subconfed | no-advertise | no-export ] * [ whole-match ] | community-list { basic-community-list-number [ whole-match ] | adv-community-list-number }&<1-16> | different-origin-as | regular-expression as-regular-expression ]

View

Any view

Default Level

1: Monitor level

Parameters

route-distinguisher: Route distinguisher (RD).

network-address: IP address of the destination segment.

mask-length: Length of the network mask, in the range 0 to 32.

mask-address: Network mask, in the format of X.X.X.X.

longer-prefixes: Matches the longest prefix.

as-path-acl as-path-acl-number: Filters routing information using the specified AS_PATH list. The as-path-acl-number argument ranges from 1 to 256.

cidr: Displays classless interdomain routing (CIDR) information.

community: Displays routing information of the specified BGP community in the routing table.

aa:nn&<1-13>: Community number. Both the aa and nn parameters range from 0 to 65535. &<1-13> means that you can enter the parameter combination up to 13 times.

no-export-subconfed: A route with this attribute is neither advertised out of the local AS, nor advertised to the other sub-ASs in the confederation.

no-advertise: A route with this attribute is not advertised to any other BGP peer.

no-export: A route with this attribute is not advertised out of the local AS or, If existing, confederation. However, it is advertised to the other sub-ASs in the confederation.

whole-match: Performs exact matching.

community-list: Displays routing information of the specified BGP community list.

basic-community-list-number: Basic community list number, in the range 1 to 99.

adv-community-list-number: Advanced community list number, in the range 100 to 199.

&<1-16>: Specifies that the argument before it can be entered up to 16 times.

different-origin-as: Displays information about routes with different AS origins.

regular-expression as-regular-expression: Displays routing information matching the specified AS regular expression.

Description

Use the display bgp vpnv4 route-distinguisher routing-table command to display the BGP VPNv4 routing information of a specified RD.

Related commands: route-distinguisher.

Examples

# Display the BGP VPNv4 routing information of RD 100:1.

<Sysname> display bgp vpnv4 route-distinguisher 100:1 routing-table

Total routes of vpn-instance vpn1: 5

Network NextHop Label(recv/app) MED LocPrf

*>i 10.0.0.0 1.1.1.1 0 100

*> 10.1.1.0/24 0.0.0.0 (NULL /1025 ) 0

*> 20.0.0.0 10.1.1.1 (NULL /1026 ) 0

*>i 123.1.1.1/32 1.1.1.1 0 100

*> 124.1.1.1/32 0.0.0.0 (NULL /1024 ) 0

Table 1-9 Fields of display bgp vpnv4 route-distinguisher routing-table

Field	Description
Total routes of vpn-instance vpn1	Total number of routes of the specified VPN instance
Network	Network address
NextHop	Address of the next hop
Label(recv/app)	Incoming/outgoing label
MED	Metric associated with the destination network
LocPrf	Local preference

# Display the BGP VPNv4 routing information of RD 100:1, with the network segment address being 10.0.0.0.

<Sysname> display bgp vpnv4 route-distinguisher 100:1 routing-table 10.0.0.0 255.0.0.0

Route Distinguisher: 100:1

Total number of routes: 1

BGP Local router ID is 2.2.2.2

Status codes: * - valid, > - best, d - damped,

h - history, i - internal, s - suppressed, S - Stale

Origin : i - IGP, e - EGP, ? - incomplete

Network NextHop Label(recv/app) MED LocPrf

*>i 10.0.0.0 1.1.1.1 (1025 /NULL ) 0 100

Table 1-10 Fields of the above output

Field	Description
Route Distinguisher	RD
Total number of routes	Total number of routes
BGP Local router ID	Router ID of the local BGP router
Status codes	Route status codes. Valid values include: * - valid: Valid route > - best: Best route d - damped: Route damped for route flap h - history: History route i - internal: Internal route s - suppressed: Suppressed route S - Stale: Stale route
Origin	Route origin codes. Valid values include: i - IGP (learned from the AS) e - EGP (learned through EGP) ? - incomplete (learned in any other way)
Network	Network address in the BGP routing table
NextHop	Address of the next hop
Label(recv/app)	Incoming/outgoing label
MED	Metric associated with the destination network
LocPrf	Local preference
Total Number of Routes	Total number of routes of the specified VPN instance

1.1.12 display bgp vpnv4 routing-table label

Syntax

display bgp vpnv4 { all | vpn-instance vpn-instance-name } routing-table label

View

Any view

Default Level

1: Monitor level

Parameters

all: Specifies all VPNv4 peers.

vpn-instance-name: Name of the VPN instance.

Description

Use the display bgp vpnv4 routing-table label command to display information about labeled routes in the BGP routing table.

Examples

# Display information about labeled routes in the BGP routing table.

<Sysname> display bgp vpnv4 all routing-table label

Total number of routes from all PE: 1

BGP Local router ID is 2.2.2.2

Status codes: * - valid, > - best, d - damped,

h - history, i - internal, s - suppressed, S - Stale

Origin : i - IGP, e - EGP, ? - incomplete

Route Distinguisher: 100:1

Network NextHop In/Out Label

*>i 123.1.1.1 1.1.1.1 NULL/1024

Total routes of vpn-instance vpn1: 4

Network NextHop In/Out Label

*> 10.1.1.0 0.0.0.0 1025/NULL

*> 20.0.0.0 0.0.0.0 1026/NULL

*>i 123.1.1.1 1.1.1.1 NULL/1024

*> 124.1.1.1 0.0.0.0 1024/NULL

Table 1-11 Description on the fields of display bgp vpnv4 routing-table label

Field	Description
Total number of routes from all PE	Total number of routes from all PEs
BGP Local router ID	Router ID of the local BGP router
Status	Route status codes. Valid values include: * - valid: Valid route > - best: Best route d - damped: Route damped for route flap h - history: History route i - internal: Internal route s - suppressed: Suppressed route S - Stale: Stale route
Origin	Route origin codes. Valid values include: i - IGP (learned from the AS) e - EGP (learned through EGP) ? - incomplete (learned in any other way)
Route Distinguisher	RD
Network	Network address
NextHop	Address of the next hop
In/Out Label	Incoming/outgoing label. exp-null indicates an explicit null label.
Total routes of vpn-instance vpn1	Total number of routes from the specified VPN instance

1.1.13 display bgp vpnv4 vpn-instance routing-table

Syntax

display bgp vpnv4 vpn-instance vpn-instance-name routing-table [ network-address [ { mask | mask-length } [ longer-prefixes ] ] | as-path-acl as-path-acl-number | cidr | community [ aa:nn ]&<1-13>[ no-export-subconfed | no-advertise | no-export ]* [ whole-match ] | community-list { basic-community-list-number [ whole-match ] | adv-community-list-number }&<1-16> | dampened | dampening parameter | different-origin-as | flap-info [ as-path-acl as-path-acl-number | network-address [ mask [ longer-match ] | mask-length [ longer-match ] ] | regular-expression as-regular-expression ] | peer ip-address { advertised-routes | received-routes } | regular-expression as-regular-expression | statistic ]

View

Any view

Default Level

1: Monitor level

Parameters

vpn-instance-name: Name of the VPN instance.

network-address: IP address of the destination segment.

mask: Network mask, in the format of X.X.X.X.

mask-length: Length of the network mask.

longer-prefixes: Specifies to match the longest prefix.

as-path-acl as-path-acl-number: Filters routing information using the specified AS_PATH list.

cidr: Displays classless interdomain routing (CIDR) information.

community: Displays routing information of the specified BGP community in the routing table.

aa:nn&<1-13>: Community number. &<1-13> means that you can enter the parameter combination up to 13 times.

no-export-subconfed: A route with this attribute is neither advertised out of the local AS, nor advertised to the other sub-ASs in the confederation.

no-advertise: A route with this attribute is not advertised to any other BGP peer.

no-export: A route with this attribute is not advertised out of the local AS or, If existing, confederation. However, it is advertised to the other sub-ASs in the confederation.

whole-match: Performs exact match.

community-list: Displays routing information of the specified BGP community list.

basic-community-list-number: Basic community list number.

adv-community-list-number: Advanced community list number.

&<1-16>: Specifies that the argument before it can be entered up to 16 times.

dampened: Displays information about dampened BGP VPNv4 routes.

dampening parameter: Displays information about configured BGP VPNv4 route dampening parameters.

different-origin-as: Displays information about routes with different AS origins.

flap-info: Displays BGP VPNv4 route flap statistics.

longer-match: Displays flap statistics for routes with masks longer than that specified by the network-address { mask | mask-length } combination.

peer ip-address: Specifies a peer by its IP address.

advertised-routes: Displays routing information sent to the specified peer.

received-routes: Displays routing information received from the specified peer.

regular-expression as-regular-expression: Displays routing information matching the specified AS regular expression.

statistic: Displays BGP VPNv4 route statistics.

Description

Use the display bgp vpnv4 vpn-instance routing-table command to display the BGP VPNv4 routing information of a specified VPN instance.

Examples

# Display the BGP VPNv4 routing information of VPN instance vpn1.

<Sysname> display bgp vpnv4 vpn-instance vpn1 routing-table

Total Number of Routes: 5

BGP Local router ID is 2.2.2.2

Status codes: * - valid, > - best, d - damped,

h - history, i - internal, s - suppressed, S - Stale

Origin : i - IGP, e - EGP, ? - incomplete

Network NextHop MED LocPrf PrefVal Path/Ogn

*>i 10.0.0.0 1.1.1.1 0 100 0 i

*> 10.1.1.0/24 0.0.0.0 0 0 ?

*> 20.0.0.0 10.1.1.1 0 99 200?

*>i 123.1.1.1/32 1.1.1.1 0 100 0 ?

*> 124.1.1.1/32 0.0.0.0 0 0 ?

Table 1-12 Fields of display bgp vpnv4 vpn-instance routing-table

Field	Description
Total Number of Routes	Total number of routes
BGP Local router ID	ID of the BGP-enabled local router
Status codes	Route status codes. Valid values include: * - valid: Valid route > - best: Best route d - damped: Route damped for route flap h - history: History route i - internal: Internal route s - suppressed: Suppressed route S - Stale: Stale route
Origin	Route origin codes. Valid values include: i - IGP (learned from the AS) e - EGP (learned through EGP) ? - incomplete (learned in any other way)
Network	Network address in the BGP routing table
NextHop	Address of the next hop
MED	Metric associated with the destination network
LocPrf	Local preference
PrefVal	Preferred value of the protocol
Path/Ogn	AS_PATH attribute/route origin of the route.

1.1.14 display fib statistics vpn-instance

Syntax

display fib statistics vpn-instance

View

Any view

Default Level

1: Monitor level

Parameters

None

Description

Use the display fib statistics vpn-instance command to display statistics about the VPN instance forwarding table.

Examples

# Display statistics about the VPN instance forwarding table.

<Sysname> display fib statistics vpn-instance

Route Entry Count : 10

Table 1-13 Description on the fields of display fib statistics vpn-instance

Field	Description
Route Entry Count	Total route number of all created VPN instances

1.1.15 display fib vpn-instance

Syntax

display fib vpn-instance vpn-instance-name [ include text ]

View

Any view

Default Level

1: Monitor level

Parameters

vpn-instance-name: Name of the VPN instance.

include text: Displays only information that includes the specified string.

Description

Use the display fib vpn-instance command to display information about the forwarding information base (FIB) of a VPN instance.

Examples

# Display information about the FIB of VPN instance vpn1.

<Sysname> display fib vpn-instance vpn1

FIB Table For vpn1:

Total number of Routes : 2

Destination/Mask OutInterface InnerLabel Token

66.1.1.1/32 InLoopBack0 NULL invalid

66.1.1.0/24 Vlan-interface 12 NULL invalid

Table 1-14 Description on the fields of the display fib vpn-instance command

Field	Description
FIB Table For vpn1	FIB information about VPN instance vpn1
Total number of Routes	Total number of routes
Destination/Mask	Forwarding destination address and mask of the VPN instance
OutInterface	Outbound interface of the VPN instance
InnerLabel	Inner label
Token	Token

1.1.16 display ip vpn-instance

Syntax

display ip vpn-instance [ instance-name vpn-instance-name ]

View

Any view

Default Level

1: Monitor level

Parameters

vpn-instance-name: Name of the VPN instance.

Description

Use the display ip vpn-instance command to display information about a VPN instance or all VPN instances.

If you do not specify any parameter, the command displays brief information about all VPN instances.

Examples

# Display information about VPN instance vpn1.

<Sysname> display ip vpn-instance instance-name vpn1

VPN-Instance Name and ID : vpn1, 1

Create time : 2006/04/08 13:01:30

Up time : 0 days, 00 hours, 11 minutes and 42 seconds

Route Distinguisher : 22:1

Export VPN Targets : 3:3 5:5

Import VPN Targets : 4:4 5:5

Import Route Policy : poly-1

Description : This is vpn1

Maximum number of Routes : 500

Interfaces : vlan-interface12

Table 1-15 Description on the fields of display ip vpn-instance instance-name

Field	Description
VPN-Instance Name and ID	Name and ID of the VPN instance
CreateTime	Time when the VPN instance was created
Up time	Duration of the VPN instance
Route Distinguisher	RD of the VPN instance
Export VPN Targets	Export target attribute of the VPN instance
Import VPN Targets	Import target attribute of the VPN instance
Import Route Policy	Import routing policy of the VPN instance
Description	Description of the VPN instance
Maximum number of Routes	Maximum number of routes of the VPN instance
Interfaces	Interface to which the VPN instance is bound

1.1.17 display ospf sham-link

Syntax

display ospf [ process-id ] sham-link [ area area-id ]

View

Any view

Default Level

1: Monitor level

Parameters

process-id: OSPF process ID.

area-id: OSPF area ID. It can be an integer or in the format of an IPv4 address.

Description

Use the display ospf sham-link command to display information about sham links.

With neither process ID nor area ID specified, the command displays information about all configured sham links.

Related commands: sham-link.

Examples

# Display information about all OSPF sham links.

<Sysname> display ospf sham-link

OSPF Process 100 with Router ID 100.1.1.2

Sham Link:

Area NeighborId Source-IP Destination-IP State Cost

0.0.0.1 100.1.1.2 3.3.3.3 5.5.5.5 P-2-P 10

Table 1-16 Description on the fields of the display ospf sham-link command

Field	Description
Area	OSPF area to which the sham link belongs
NeighborId	Router ID of the sham link
Source-IP	Source IP address of the sham link
Destination-IP	Destination IP address of the sham link
State	Status of the sham link interface
Cost	Cost of the sham link

# Display information about OSPF sham links in area 1.

<Sysname> display ospf sham-link area 1

OSPF Process 100 with Router ID 100.1.1.2

Sham-Link: 3.3.3.3 --> 5.5.5.5

Neighbour State: Full

Area: 0.0.0.1

Cost: 10 State: P-2-P, Type: Sham

Timers: Hello 10 , Dead 40 , Retransmit 5 , Transmit Delay 1

Table 1-17 Description on the fields of the display ospf sham-link area command

Field	Description
Sham-Link	Sham link expressed in the format of source IP address to destination IP address
Neighbour State	Status of the sham link neighbor
Area	Destination IP address of the sham link
Cost	Cost of the sham link
State	Status of the sham link
Type	Type of the sham link
Timers	Timers of the sham link

1.1.18 display tunnel-policy

Syntax

display tunnel-policy { all | policy-name tunnel-policy-name }

View

Any view

Default Level

1: Monitor level

Parameters

all: Specifies all tunneling policies.

tunnel-policy-name: Name of a tunneling policy.

Description

Use the display tunnel-policy command to display information about a tunneling policy or all tunneling policies.

Related commands: tunnel-policy, tunnel select-seq load-balance-number.

Examples

# Display all tunneling policies.

<Sysname> display tunnel-policy all

Tunnel Policy Name Select-Seq Load balance No

------------------------------------------------------

t LSP 1

aaa LSP CR-LSP 1

bbb LSP 1

# Display tunneling policy aaa.

<Sysname> display tunnel-policy policy-name aaa

Tunnel Policy Name Select-Seq Load balance No

------------------------------------------------------

aaa LSP CR-LSP 1

Table 1-18 Description on the fields of the display tunnel-policy command

Field	Description
Tunnel Policy Name	Name of the tunneling policy
Select-Seq	preference order for tunnel selection
Load balance No	Number of tunnels for load balancing

1.1.19 domain-id

Syntax

domain-id domain-id [ secondary ]

undo domain-id [ domain-id ]

View

OSPF view

Default Level

2: System level

Parameters

domain-id: OSPF domain ID, in integer or dotted decimal notation.

secondary: Uses the domain ID as secondary. With this keyword not specified, the domain ID configured is primary.

Description

Use the domain-id command to configure an OSPF domain ID.

Use the undo domain-id command to restore the default.

By default, the OSPF domain ID is 0.

With no parameter specified, the undo domain-id command deletes all domain IDs.

Usually, routes injected from PEs are advertised as External-LSAs. However, routes to different destinations in the same OSPF domain must be advertised as Type-3 LSAs. Therefore, using the same domain ID for an OSPF domain is required.

Examples

# Configure the OSPF domain ID.

<Sysname> system-view

[Sysname] ospf 100

[Sysname-ospf-100] domain-id 234

1.1.20 export route-policy

Syntax

export route-policy route-policy

undo export route-policy

View

VPN instance view

Default Level

2: System level

Parameters

route-policy: Name of the export routing policy for the VPN instance.

Description

Use the export route-policy command to apply an export routing policy to a VPN instance.

Use the undo export route-policy command to remove the application.

You can configure an export routing policy when a finer control on the VPN instance routes to be redistributed is required, that is, when the control provided by the extended community attribute is not enough. An export routing policy may deny routes that are permitted by the export target attribute.

By default, all VPN instance routes permitted by the export target attribute can be redistributed.

Examples

# Apply export routing policy poly-1 to VPN instance vpn1.

<Sysname> system-view

[Sysname] ip vpn-instance vpn1

[Sysname-vpn-instance-vpn1] export route-policy poly-1

1.1.21 filter-policy export (BGP-VPNv4 subaddress family view)

Syntax

filter-policy { acl-number | ip-prefix ip-prefix-name } export [ direct | isis process-id | ospf process-id | rip process-id | static ]

undo filter-policy export [ direct | isis process-id | ospf process-id | rip process-id | static ]

View

BGP-VPNv4 subaddress family view

Default Level

2: System level

Parameters

acl-number: IP ACL number.

ip-prefix-name: IP address prefix list name.

direct: Filters direct routes to be advertised.

isis process-id: Filters ISIS routes to be advertised that are from a specified ISIS process.

ospf process-id: Filters OSPF routes to be advertised that are from a specified OSPF process..

rip process-id: Filters RIP routes to be advertised that are from a specified RIP process.

static: Filters static routes to be advertised.

Description

Use the filter-policy export command to specify to filter all or certain types of routes to be advertised.

Use the undo filter-policy export command to remove the configuration.

If you specify no routing protocol parameters for the filter-policy export command, all routes to be advertised will be filtered.

By default, MP-BGP does not filter routes to be advertised.

Only routes that survive the filtering are advertised by MP-BGP.

Examples

# In BGP-VPNv4 subaddress family view, specify to filter routes to be advertised by MP-BGP using ACL 2555.

<Sysname> system-view

[Sysname] bgp 100

[Sysname] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] filter-policy 2555 export

1.1.22 filter-policy import (BGP-VPNv4 subaddress family view)

Syntax

filter-policy { acl-number | ip-prefix ip-prefix-name } import

undo filter-policy import

View

BGP-VPNv4 subaddress family view

Default Level

2: System level

Parameters

acl-number: IP ACL number.

ip-prefix-name: IP address prefix list name.

Description

Use the filter-policy import command to specify to filter received routes.

Use the undo filter-policy import command to remove the configuration.

By default, received routes are not filtered.

Only routes that survive the filtering are added into the BGP routing table.

Examples

# In BGP-VPNv4 subaddress family view, specify to use ACL 2255 to filter received routes.

<Sysname> system-view

[Sysname] bgp 100

[Sysname] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] filter-policy 2255 import

1.1.23 import route-policy

Syntax

import route-policy route-policy

undo import route-policy

View

VPN instance view

Default Level

2: System level

Parameters

route-policy: Name of the import routing policy for the VPN instance.

Description

Use the import route-policy command to apply an import routing policy to a VPN instance.

Use the undo import route-policy command to remove the application.

You can configure an import routing policy when a finer control on the routes to be redistributed into a VPN instance is required, that is, when the control provided by the extended community attributes is not enough. An import routing policy may deny routes that are permitted by the import target attribute.

By default, all routes permitted by the import target attribute can be redistributed into the VPN instance.

Examples

# Apply import routing policy poly-1 to VPN instance vpn1.

<Sysname> system-view

[Sysname] ip vpn-instance vpn1

[Sysname-vpn-instance-vpn1] import route-policy poly-1

1.1.24 ip binding vpn-instance

Syntax

ip binding vpn-instance vpn-instance-name

undo ip binding vpn-instance vpn-instance-name

View

Interface view

Default Level

2: System level

Parameters

vpn-instance-name: Name of the VPN instance to be associated.

Description

Use the ip binding vpn-instance command to associate an interface with a VPN instance.

Use the undo ip binding vpn-instance command to remove the association.

By default, an interface is associated with no VPN instance; it belongs to the public network.

When configured on an interface, the ip binding vpn-instance command clears the IP address of the interface. Therefore, you must re-configure the IP address of the interface after configuring the command.

Examples

# Associate interface VLAN-interface 12 with VPN instance vpn1.

<Sysname> system-view

[Sysname] interface vlan-interface 12

[Sysname-Vlan-interface12] ip binding vpn-instance vpn1

1.1.25 ip vpn-instance

Syntax

ip vpn-instance vpn-instance-name

undo ip vpn-instance vpn-instance-name

View

System view

Default Level

2: System level

Parameters

vpn-instance-name: Name for the VPN instance.

Description

Use the ip vpn-instance command to create a VPN instance and enter VPN instance view.

Use the undo ip vpn-instance command to delete a VPN instance.

A VPN instance takes effect only after you configure an RD for it.

Related commands: route-distinguisher.

Examples

# Create a VPN instance named vpn1.

<Sysname> system-view

[Sysname] ip vpn-instance vpn1

[Sysname-vpn-instance-vpn1]

1.1.26 ipv4-family

Syntax

ipv4-family { vpnv4 | vpn-instance vpn-instance-name }

undo ipv4-family { vpnv4 | vpn-instance vpn-instance-name }

View

BGP view

Default Level

2: System level

Parameters

vpnv4: Enters BGP-VPNv4 subaddress family view.

vpn-instance vpn-instance-name: Associates a VPN instance with an IPv4 address family and enter BGP VPN instance view.

Description

Use the ipv4-family command to enter BGP-VPNv4 subaddress family view or BGP VPN instance view.

Use the undo ipv4-family command to remove all configurations performed in either of the two views.

Before entering BGP VPN instance view, you must create the VPN instance.

Examples

# Enter BGP-VPNv4 subaddress family view.

<Sysname> system-view

[Sysname] bgp 100

[Sysname] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4]

# Associate VPN instance vpn1 with an IPv4 address family and enter BGP VPN instance view.

<Sysname> system-view

[Sysname] ip vpn-instance vpn1

[Sysname-vpn-instance-vpn1] quit

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpn-instance vpn1

[Sysname-bgp-vpn1]

1.1.27 peer advertise-community (BGP-VPNv4 subaddress family view)

Syntax

peer { group-name | ip-address } advertise-community

undo peer { group-name | ip-address } advertise-community

View

BGP-VPNv4 subaddress family view

Default Level

2: System level

Parameters

group-name: Name of the peer group.

ip-address: IP address of the peer.

Description

Use the peer advertise-community command to specify to advertise community attributes to a peer or peer group.

Use the undo peer advertise-community command to remove the configuration.

By default, no community attributes are advertised to any peer or peer group.

Examples

# In BGP-VPNv4 subaddress family view, specify to advertise community attributes to peer 3.3.3.3.

<Sysname> system-view

[Sysname] bgp 100

[Sysname] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] peer 3.3.3.3 advertise-community

1.1.28 peer allow-as-loop

Syntax

peer { group-name | ip-address } allow-as-loop [ number ]

undo peer { group-name | ip-address } allow-as-loop

View

BGP-VPNv4 subaddress family view/BGP-L2VPN address family view/VPLS address family view

Default Level

2: System level

Parameters

group-name: Name of the peer group.

ip-address: IP address of the peer.

number: Maximum number that the local AS number can appear repeatedly in the AS-PATH attribute. It ranges from 1 to 10 and defaults to 1.

Description

Use the peer allow-as-loop command to allow the local AS number to appear in the AS-PATH attribute of a received route and to set the allowed maximum number of repetitions.

Use the undo peer allow-as-loop command to remove the configuration.

Examples

# In BGP-VPNv4 subaddress family view, allow the local AS number to appear repeatedly in the AS-PATH attribute of a route received from peer 1.1.1.1 for up to twice.

<Sysname> system-view

[Sysname] bgp 100

[Sysname] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] peer 1.1.1.1 allow-as-loop 2

# In BGP-L2VPN address family view, allow the local AS number to appear repeatedly in the AS-PATH attribute of a route received from peer 1.1.1.1 for up to twice.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] l2vpn-family

[Sysname-bgp-af-l2vpn] peer 1.1.1.1 allow-as-loop 2

# In VPLS address family view, allow the local AS number to appear repeatedly in the AS-PATH attribute of a route received from peer 1.1.1.1 for up to twice.

<Sysname> system-view

[Sysname] bgp 100

[Sysname] vpls-family

[Sysname-bgp-af-vpls] peer 1.1.1.1 allow-as-loop 2

1.1.29 peer as-path-acl (BGP-VPNv4 subaddress family view)

Syntax

peer { ip-address | group-name } as-path-acl aspath-filter-number { import | export }

undo peer { ip-address | group-name } as-path-acl aspath-filter-number { import | export }

View

BGP-VPNv4 subaddress family view

Default Level

2: System level

Parameters

ip-address: IP address of the peer.

group-name: Name of the peer group.

aspath-filter-number: AS_PATH filtering list number.

import: Filters the received routes.

export: Filters the routes to be advertised.

Description

Use the peer as-path-acl command to specify to filter routes received from or to be advertised to a specified peer or peer group based on an AS_PATH list.

Use the undo peer as-path-acl command to remove the configuration.

By default, no AS filtering list is applied to a peer or peer group.

Examples

# In BGP-VPNv4 subaddress family view, apply AS filtering list 3 to routes advertised by peer group test.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] peer test as-path-acl 3 export

1.1.30 peer default-route-advertise vpn-instance

Syntax

peer { group-name | ip-address } default-route-advertise vpn-instance vpn-instance-name

undo peer { group-name | ip-address } default-route-advertise vpn-instance vpn-instance-name

View

BGP-VPNv4 subaddress family view

Default Level

2: System level

Parameters

group-name: Name of the peer group.

ip-address: IP address of the peer.

vpn-instance-name: Name of the VPN instance.

Description

Use the peer default-route-advertise vpn-instance command to specify to advertise all default routes of a VPN instance to a peer or peer group.

Use the undo peer default-route-advertise vpn-instance command to remove the configuration.

By default, no default route is advertised to a peer or peer group.

Related commands: peer upe.

Examples

# In BGP-VPNv4 subaddress family view, specify to advertise default routes of VPN instance vpn1 to peer 1.1.1.1.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp-af-vpnv4] peer 1.1.1.1 enable

[Sysname-bgp-af-vpnv4] peer 1.1.1.1 upe

[Sysname-bgp-af-vpnv4] peer 1.1.1.1 default-route-advertise vpn-instance vpn1

1.1.31 peer enable

Syntax

peer { ip-address | group-name } enable

undo peer { ip-address | group-name } enable

View

BGP-VPNv4 subaddress family view/BGP-L2VPN address family view/VPLS address family view

Default Level

2: System level

Parameters

ip-address: IP address of the peer.

group-name: Name of the peer group.

Description

Use the peer enable command to enable a peer or peer group for an address family and enable the exchange of BGP routing information of the address family.

Use the undo peer enable command to disable the capability.

By default, only IPv4 routing information is exchanged between BGP peers/peer groups.

Examples

# Configure peer 1.1.1.1 and enable the peer for the BGP-VPNv4 subaddress family.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] peer 1.1.1.1 as-number 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] peer 1.1.1.1 enable

# Configure peer 1.1.1.1 and enable the peer for the BGP-L2VPN address family.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] peer 1.1.1.1 as-number 100

[Sysname-bgp] l2vpn-family

[Sysname-bgp-af-l2vpn] peer 1.1.1.1 enable

# Configure peer 1.1.1.1 and enable the peer for the VPLS address family.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] peer 1.1.1.1 as-number 100

[Sysname] vpls-family

[Sysname-bgp-af-vpls] peer 1.1.1.1 enable

1.1.32 peer filter-policy (BGP-VPNv4 subaddress family view)

Syntax

peer { ip-address | group-name } filter-policy acl-number { import | export }

undo peer { ip-address | group-name } filter-policy acl-number { import | export }

View

BGP-VPNv4 subaddress family view

Default Level

2: System level

Parameters

ip-address: IP address of the peer.

group-name: Name of the peer group.

acl-number: ACL number.

import: Filters the received routes.

export: Filters the routes to be advertised.

Description

Use the peer filter-policy command to apply a filtering policy to a peer or peer group .

Use the undo peer filter-policy command to remove the configuration.

By default, no filtering policy is applied to a peer or peer group.

Related commands: peer as-path-acl.

Examples

# Apply a filtering policy to filter the received routes of a peer group.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] peer test filter-policy 2003 import

1.1.33 peer group

Syntax

peer ip-address group group-name

undo peer ip-address group group-name

View

BGP-VPNv4 subaddress family view/BGP-L2VPN address family view/VPLS address family view

Default Level

2: System level

Parameters

group-name: Name of the peer group.

ip-address: IP address of the peer.

Description

Use the peer group command to add a peer into an existing peer group.

Use the undo peer group command to remove a peer from a peer group.

Examples

# In BGP-VPNv4 subaddress family view, add peer 1.1.1.1 into peer group test.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] group test external

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] peer 1.1.1.1 group test

# In BGP-L2VPN address family view, add peer 1.1.1.1 into peer group test.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] group test external

[Sysname-bgp] l2vpn-family

[Sysname-bgp-af-l2vpn] peer 1.1.1.1 group test

# In VPLS address family view, add peer 1.1.1.1 into peer group test.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] group test external

[Sysname] vpls-family

[Sysname-bgp-af-vpls] peer 1.1.1.1 group test

1.1.34 peer ip-prefix (BGP-VPNv4 subaddress family view)

Syntax

peer { ip-address | group-name } ip-prefix prefix-name { import | export }

undo peer { ip-address | group-name } ip-prefix prefix-name { import | export }

View

BGP-VPNv4 subaddress family view

Default Level

2: System level

Parameters

ip-address: IP address of the peer.

group-name: Name of the peer group.

prefix-name: Name of the IP prefix list.

import: Filters the received routes.

export: Filters the routes to be advertised.

Description

Use the peer ip-prefix command to apply a route filtering policy based on IP prefix list to a peer or peer group.

Use the undo peer ip-prefix command to remove the configuration.

By default, no route filtering policy based on IP prefix list is applied to a peer or peer group.

Examples

# In BGP-VPNv4 subaddress family view, specify to filter the received routes of a peer group using IP prefix list list1.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] peer group1 ip-prefix list1 import

1.1.35 peer label-route-capability (BGP view/BGP VPN instance view)

Syntax

peer { ip-address | group-name } label-route-capability

undo peer { ip-address | group-name } label-route-capability

View

BGP view/BGP VPN instance view

Default Level

2: System level

Parameters

ip-address: IP address of the peer.

group-name: Name of the peer group.

Description

Use the peer label-route-capability command to enable the exchange of labeled routes with an IPv4 peer or peer group.

Use the undo peer label-route-capability command to disable the capability.

By default, the device does not advertise labeled routes to an IPv4 peer.

According to the networking scheme, the peer label-route-capability command enables the exchange of labeled IPv4 routes with:

l ASBR PEs in the same AS.

l PEs in the same AS.

l the peer ASBR PE.

Examples

# Specify to exchange labeled IPv4 routes with peer 2.2.2.2.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] peer 2.2.2.2 label-route-capability

1.1.36 peer next-hop-invariable (BGP-VPNv4 subaddress family view)

Syntax

peer { ip-address | group-name } next-hop-invariable

undo peer { ip-address | group-name } next-hop-invariable

View

BGP-VPNv4 subaddress family view

Default Level

2: System level

Parameters

ip-address: IP address of the peer.

group-name: Name of the peer group.

Description

Use the peer next-hop-invariable command to configure the device not to change the next hop of a route when advertising it to an EBGP peer.

Use the undo peer next-hop-invariable command to restore the default.

By default, a device uses its address as the next hop when advertising a route to its EBGP peer.

Related commands: refer to BGP Commands.

Examples

# In BGP-VPNv4 subaddress family view, configure the device not to change the next hop of a route when advertising it to EBGP peer 1.1.1.1.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] peer 1.1.1.1 next-hop-invariable

1.1.37 peer next-hop-local

Syntax

peer { group-name | ip-address } next-hop-local

undo peer { group-name | ip-address } next-hop-local

View

BGP-VPNv4 subaddress family view/BGP-L2VPN address family view/VPLS address family view

Default Level

2: System level

Parameters

group-name: Name of the peer group.

ip-address: IP address of the peer.

Description

Use the peer next-hop-local command to configure the device to use the local address as the next hop of a route when advertising it to a peer or peer group.

Use the undo peer next-hop-local command to remove the configuration.

Examples

# In BGP-VPNv4 subaddress family view, configure the device to use the local address as the next hop of a route when advertising it to peer group test.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] peer test next-hop-local

# In BGP-L2VPN address family view, configure the device to use the local address as the next hop of a route when advertising it to peer group test.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] l2vpn-family

[Sysname-bgp-af-l2vpn] peer test next-hop-local

# In VPLS address family view, configure the device to use the local address as the next hop of a route when advertising it to peer group test.

<Sysname> system-view

[Sysname] bgp 100

[Sysname] vpls-family

[Sysname-bgp-af-vpls] peer test next-hop-local

1.1.38 peer public-as-only (BGP-VPNv4 subaddress family view)

Syntax

peer { group-name | ip-address } public-as-only

undo peer { group-name | ip-address } public-as-only

View

BGP-VPNv4 subaddress family view

Default Level

2: System level

Parameters

group-name: Name of the peer group.

ip-address: IP address of the peer.

Description

Use the peer public-as-only command to make outbound BGP updates carry no private AS numbers.

Use the undo peer public-as-only command to make outbound BGP updates carry private AS numbers.

By default, a BGP update carries private AS numbers.

If a BGP update to be sent carries any public AS number, this command does not take effect. The private AS number ranges from 64512 to 65535.

Examples

# In BGP-VPNv4 subaddress family view, configure the device to make BGP updates to be sent to peer group test carry no private AS numbers.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] peer test public-as-only

1.1.39 peer reflect-client

Syntax

peer { group-name | ip-address } reflect-client

undo peer { group-name | ip-address } reflect-client

View

BGP-VPNv4 subaddress family view/BGP-L2VPN address family view/VPLS address family view

Default Level

2: System level

Parameters

group-name: Name of the peer group.

ip-address: IP address of the peer.

Description

Use the peer reflect-client command to configure the local device to be a route reflector (RR) and set a peer or peer group as the client of the RR.

Use the undo peer reflect-client command to remove the configuration.

By default, no RR or RR client is configured.

Examples

# In BGP-VPNv4 subaddress family view, configure the local device to be an RR and set peer group test as the client of the RR.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] peer test reflect-client

# In BGP-L2VPN address family view, configure the local device to be an RR and set peer group test as the client of the RR.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] l2vpn-family

[Sysname-bgp-af-l2vpn] peer test reflect-client

# In VPLS address family view, configure the local device to be an RR and set peer group test as the client of the RR.

<Sysname> system-view

[Sysname] bgp 100

[Sysname] vpls-family

[Sysname-bgp-af-vpls] peer test reflect-client

1.1.40 peer route-policy (BGP-VPNv4 subaddress family view)

Syntax

peer { ip-address | group-name } route-policy route-policy-name { import | export }

undo peer { ip-address | group-name } route-policy route-policy-name { import | export }

View

BGP-VPNv4 subaddress family view

Default Level

2: System level

Parameters

ip-address: IP address of the peer.

group-name: Name of the peer group.

route-policy-name: Name of the routing policy.

import: Filters the received routes.

export: Filters the routes to be advertised.

Description

Use the peer route-policy command to apply a routing policy to a peer or peer group.

Use the undo peer route-policy command to remove the application.

By default, no routing policy is applied to a peer or peer group.

Examples

# In BGP-VPNv4 subaddress family view, apply routing policy test-policy to peer group test to filter the received routes.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] peer test route-policy test-policy import

1.1.41 peer upe

Syntax

peer { ip-address | group-name } upe

undo peer { ip-address | group-name } upe

View

BGP-VPNv4 subaddress family view

Default Level

2: System level

Parameters

ip-address: IP address of the peer.

group-name: Name of the peer group.

Description

Use the peer upe command to configure a BGP peer or peer group as an HoVPN UPE for a BGP-VPNv4 subaddress family.

Use the undo peer upe command to remove the configuration.

UPE is a kind of special VPNv4 peer. It accepts only one default route for each related VPN instance on an SPE, rather than common VPNv4 routes. An SPE is a common VPN peer.

Examples

# Configure peer 1.1.1.1 as a UPE.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] peer 1.1.1.1 upe

1.1.42 policy vpn-target

Syntax

policy vpn-target

undo policy vpn-target

View

BGP-VPNv4 subaddress family view/BGP-L2VPN address family view/VPLS address family view

Default Level

2: System level

Parameters

None

Description

Use the policy vpn-target command to enable VPN target filtering for received VPNv4 routes.

Use the undo policy vpn-target command to disable the filtering, permitting all VPNv4 routes.

Only VPNv4 routes with export route target attributes matching the local import route target attributes are added into the routing table.

By default, the VPN target filtering function is enabled for received VPNv4 routes.

& Note:

The command applies to inter-provider VPN option B schemes.

Examples

# In BGP-VPNv4 subaddress family view, enable VPN target filtering for received VPNv4 routes.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] policy vpn-target

# In BGP-L2VPN address family view, enable VPN target filtering for received VPNv4 routes.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] l2vpn-family

[Sysname-bgp-af-l2vpn] policy vpn-target

# In VPLS address family view, enable VPN target filtering for received VPNv4 routes.

<Sysname> system-view

[Sysname] bgp 100

[Sysname] vpls-family

[Sysname-bgp-af-vpls] policy vpn-target

1.1.43 reflect between-clients

Syntax

reflect between-clients

undo reflect between-clients

View

BGP-VPNv4 subaddress family view/BGP-L2VPN address family view/VPLS address family view

Default Level

2: System level

Parameters

None

Description

Use the reflect between-clients command to enable route reflection between clients.

Use the undo reflect between-clients command to disable the function.

By default, route reflection between clients is enabled.

If fully meshed interconnections exist between the clients, route reflection is not required. Otherwise, an RR is required for routes to be reflected from one client to every other client.

Examples

# In BGP-VPNv4 subaddress family view, disable route reflection between clients.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] undo reflect between-clients

# In BGP-L2VPN address family view, disable route reflection between clients.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] l2vpn-family

[Sysname-bgp-af-l2vpn] undo reflect between-clients

# In VPLS address family view, disable route reflection between clients.

<Sysname> system-view

[Sysname] bgp 100

[Sysname] vpls-family

[Sysname-bgp-af-vpls] undo reflect between-clients

1.1.44 reflector culster-id

Syntax

reflector cluster-id { cluster-id | ip-address }

undo reflector cluster-id

View

BGP-VPNv4 subaddress family view/BGP-L2VPN address family view/VPLS address family view

Default Level

2: System level

Parameters

cluster-id: Cluster ID of the route reflector (RR).

ip-address: IP address of the peer, which is to be used as the cluster ID of the RR.

Description

Use the reflector cluster-id command to specify a cluster ID for an RR.

Use the undo reflector cluster-id command to remove the cluster ID.

By default, the cluster ID is the router ID of an RR in the cluster.

Generally, a cluster contains only one RR, in which case the router ID of the RR is used for identifying the cluster. Setting multiple RRs can improve the network reliability. When there is more than one RR in a cluster, use the reflector cluster-id command to configure the same cluster ID for all RRs in the cluster.

Examples

# In BGP-VPNv4 subaddress family view, configure the local router as an RR of a cluster.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] reflector cluster-id 50

# In BGP-L2VPN address family view, configure the local router as an RR of a cluster.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] l2vpn-family

[Sysname-bgp-af-l2vpn] reflector cluster-id 50

# In VPLS address family view, configure the local router as an RR of a cluster.

<Sysname> system-view

[Sysname] bgp 100

[Sysname] vpls-family

[Sysname-bgp-af-vpls] reflector cluster-id 50

1.1.45 refresh bgp vpn-instance

Syntax

refresh bgp vpn-instance vpn-instance-name { all | ip-address | group group-name | external } { import | export }

View

User view

Default Level

1: Monitor level

Parameters

vpn-instance-name: Name of the VPN instance.

all: Performs a soft reset of all BGP VPN instance connections.

ip-address: Performs a soft reset of the BGP connection with a BGP peer identified by this IP address.

group group-name: Performs a soft reset of the connections with a BGP peer group identified by this name.

external: Performs a soft reset of EBGP sessions.

import: Performs a soft reset in the inbound direction.

export: Performs a soft reset in the outbound direction.

Description

Use the refresh bgp vpn-instance command to perform a soft reset of BGP connections in a VPN instance.

Examples

# Perform a soft reset of all BGP connections in VPN instance vpn1 in the inbound direction to make new configurations take effect.

<Sysname> refresh bgp vpn-instance vpn1 all import

1.1.46 refresh bgp vpnv4

Syntax

refresh bgp vpnv4 { all | ip-address | group group-name | internal | external } { import | export }

View

User view

Default Level

1: Monitor level

Parameters

all: Performs a soft reset of all BGP VPNv4 connections.

ip-address: Performs a soft reset of the BGP VPNv4 connection with a BGP peer identified by this IP address.

group group-name: Performs a soft reset of the VPNv4 connections with a BGP peer group identified by this name.

internal: Performs a soft reset of IBGP sessions.

external: Performs a soft reset of EBGP sessions.

import: Performs a soft reset in the inbound direction.

export: Performs a soft reset in the outbound direction.

Description

Use the refresh bgp vpnv4 command to perform a soft reset of BGP VPNv4 connections.

Examples

# Perform a soft reset of all BGP VPNv4 connections in the inbound direction to make new configurations take effect.

<Sysname> refresh bgp vpnv4 all import

1.1.47 reset bgp vpn-instance

Syntax

reset bgp vpn-instance vpn-instance-name { as-number | ip-address | all | external | group group-name }

View

User view

Default Level

1: Monitor level

Parameters

vpn-instance-name: Name of the VPN instance.

as-number: Resets BGP connections with the peers in an AS identified by this number.

ip-address: Resets the connection with a BGP peer identified by this IP address.

group group-name: Resets the connections with a BGP peer group identified by this name.

all: Resets all BGP connections.

external: Resets EBGP sessions.

Description

Use the reset bgp vpn-instance command to reset the BGP connections of a VPN instance.

Examples

# Reset all BGP connections of VPN instance vpn1.

<Sysname> reset bgp vpn-instance vpn1 all

1.1.48 reset bgp vpn-instance dampening

Syntax

reset bgp vpn-instance vpn-instance-name dampening [ network-address [ mask | mask-length ] ]

View

User view

Default Level

1: Monitor level

Parameters

vpn-instance-name: Name of the VPN instance.

dampening: Specifies route flap dampening information.

mask: Network mask, in the format of X.X.X.X.

mask-length: Length of the network mask.

Description

Use the reset bgp vpn-instance dampening command to clear the route flap dampening information of a VPN instance.

Examples

# Clear the route flap dampening information of VPN instance vpn1.

<Sysname> reset bgp vpn-instance vpn1 dampening

1.1.49 reset bgp vpn-instance flap-info

Syntax

reset bgp vpn-instance vpn-instance-name ip-address flap-info

reset bgp vpn-instance vpn-instance-name flap-info [ ip-address [ mask | mask-length ] | as-path-acl as-path-acl-number | regexp as-path-regexp ]

View

User view

Default Level

1: Monitor level

Parameters

vpn-instance-name: Name of the VPN instance.

ip-address: IP address of the BGP peer.

mask: Network mask, in the format of X.X.X.X.

mask-length: Length of the network mask.

as-path-acl-number: Number of the AS_PATH list.

as-path-regexp: AS_PATH regular expression.

Description

Use the reset bgp vpn-instance flap-info command to clear the route flap history information about BGP peers of a VPN instance.

Examples

# Clear route flap history information about BGP peer 2.2.2.2 of VPN instance vpn1.

<Sysname> reset bgp vpn-instance vpn1 2.2.2.2 flap-info

1.1.50 reset bgp vpnv4

Syntax

reset bgp vpnv4 { as-number | ip-address | group group-name | all | internal | external }

View

User view

Default Level

1: Monitor level

Parameters

as-number: Resets VPNv4 connections with the peers in an AS identified by this number.

ip-address: Resets the VPNv4 connection with a BGP peer identified by this IP address.

group-name: Resets the VPNv4 connections with a BGP peer group identified by this name.

all: Resets all BGP VPNv4 connections.

internal: Resets IBGP sessions of VPNv4 connections.

external: Resets EBGP sessions of VPNv4 connections.

Description

Use the reset bgp vpnv4 command to reset BGP VPNv4 connections.

Examples

# Reset all BGP VPNv4 connections to make new configurations take effect.

<Sysname> reset bgp vpnv4 all

1.1.51 route-distinguisher (VPN instance view)

Syntax

route-distinguisher route-distinguisher

View

VPN instance view

Default Level

2: System level

Parameters

route-distinguisher: Route distinguisher (RD) for the VPN instance, a string of 3 to 21 characters in either of the following two formats:

l 16-bit AS number:32-bit user-defined number. For example, 101:3.

l 32-bit IP address:16-bit user-defined number. For example, 192.168.122.15:1.

Description

Use the route-distinguisher command to configure a route distinguisher (RD) for a VPN instance.

An RD is used to create the routing and forwarding table of a VPN. By prefixing an RD to an IPv4 prefix, you get a VPN IPv4 prefix unique globally.

& Note:

l No RD is configured by default; you must configure an RD for each VPN instance.

l A VPN instance takes effect only after you configure an RD for it.

l Once you configure an RD for a VPN, you cannot remove the association.

l You cannot change an RD directly; you can only delete the VPN instance, and then re-create the VPN instance and re-configure a new RD.

Examples

# Configure the RD of VPN instance vpn1.

<Sysname> system-view

[Sysname] ip vpn-instance vpn1

[Sysname-vpn-instance-vpn1] route-distinguisher 22:1

1.1.52 route-tag

Syntax

route-tag tag-value

undo route-tag

View

OSPF view

Default Level

2: System level

Parameters

tag-value: Tag for identifying injected VPN routes.

Description

Use the route-tag command to configure the tag for identifying injected VPN routes.

Use the undo route-tag command to restore the default.

The first two octets of the default tag is always 0xD000, while the last two octets is the AS number of the local BGP. For example, if the local BGP AS number is 100, the default tag is 3489661028 in decimal.

An OSPF instance-related VPN instance on a PE is usually configured with a VPN route tag, which must be included in Type 5/7 LSAs. PEs in the same AS are recommended to have the same route tag. The route tag is local significant and can be configured and take effect on only PEs receiving BGP routes and generating OSPF LSAs; it is not transferred in any BGP extended community attribute. Different OSPF processes can have the same route tag.

Tags configured with different commands have different priorities:

l A tag configured with the import-route command has the highest priority.

l A tag configured with the route-tag command has the second highest priority.

l A tag configured with the default tag command has the lowest priority.

A received Type 5 or Type 7 LSA is neglected in route calculation if its tag is the same as the local one.

& Note:

A configured route tag takes effect after you issue the reset ospf command.

Related commands: import-route in OSPF Commands.

Examples

# Configure the route tag for OSPF process 100 as 100.

<Sysname> system-view

[Sysname] ospf 100

[Sysname-ospf-100] route-tag 100

1.1.53 routing-table limit

Syntax

routing-table limit number { warn-threshold | simply-alert }

undo routing-table limit

View

VPN instance view

Default Level

2: System level

Parameters

number: Maximum number of routes for the VPN instance to support.

warn-threshold: Threshold for rejecting new routes. It is expressed in the percentage of the specified maximum number of routes for the VPN instance.

simply-alert: Specifies that when the maximum number of routes exceeds the threshold, the system still accepts routes and generates only a SYSLOG error message.

Description

Use the routing-table limit command to limit the maximum number of routes in a VPN instance, preventing too many routes from being accepted by a PE.

Use he undo routing-table limit command to restore the default.

Examples

# Specify that VPN instance vpn1 can receive up to 1000 routes, and can receive new routes after the threshold is exceeded.

<Sysname> system-view

[Sysname] ip vpn-instance vpn1

[Sysname-vpn-instance-vpn1] route-distinguisher 100:1

[Sysname-vpn-instance-vpn1] routing-table limit 1000 simply-alert

1.1.54 rr-filter

Syntax

rr-filter extended-community-list-number

undo rr-filter

View

BGP-VPNv4 subaddress family view/BGP-L2VPN address family view/VPLS address family view

Default Level

2: System level

Parameters

extended-community-list-number: Number of the extended community list supported by the RR group.

Description

Use the rr-filter command to create an RR reflection policy.

Use the undo rr-filter command to disable the function.

Only IBGP routes whose route target extended community attributes satisfy the matching conditions are reflected. This provides a way to implement load balancing between RRs.

Examples

# In BGP-VPNv4 subaddress family view, create an RR group and configure it to automatically filter the incoming VPNv4 route update packets based on the route target extended community attribute.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family vpnv4

[Sysname-bgp-af-vpnv4] rr-filter 10

# In BGP-L2VPN address family view, create an RR group and configure it to automatically filter the incoming VPNv4 route update packets based on the route target extended community attribute.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] l2vpn-family

[Sysname-bgp-af-l2vpn] rr-filter 10

# In VPLS address family view, create an RR group and configure it to automatically filter the incoming VPNv4 route update packets based on the route target extended community attribute.

<Sysname> system-view

[Sysname] bgp 100

[Sysname] vpls-family

[Sysname-bgp-af-vpls] rr-filter 10

1.1.55 sham-link

Syntax

sham-link source-ip-address destination-ip-address [ cost cost | dead dead-interval | hello hello-interval | retransmit retrans-interval | trans-delay delay | simple [ cipher | plain ] password1 | { md5 | hmac-md5 } key-id [ cipher | plain ] password2 ] *

undo sham-link source-ip-address destination-ip-address [ cost | dead | hello | retransmit | trans-delay | simple | { md5 | hmac-md5 } key-id ] *

View

OSPF area view

Default Level

2: System level

Parameters

source-ip-address: Source IP address for the sham link.

destination-ip-address: Destination IP address for the sham link.

cost: Cost for the sham link, one by default.

dead-interval: Dead Interval in seconds, 40 seconds by default. It must be equal to the dead interval of the router on the other end of the virtual link and be at least four times the hello interval.

hello-interval: Interval at which the interface sends Hello packets, 10 seconds by default. It must be equal to the hello interval of the router on the other end of the virtual link.

retrans-interval: Interval at which the interface retransmits LSAs, five seconds by default.

delay: Delay interval before the interface sends an LSA, one second by default.

simple [ cipher | plain ] password1: Uses simple authentication. If you specify neither the cipher nor the plain keyword, the password1 argument is a string of 1 to 8 characters. For the plain mode, the password1 argument is a string of 1 to 8 characters. For the cipher mode, the password1 argument can be either a string of 1 to 8 characters in plain text, or a string of 24 characters in cipher text.

md5: Uses MD5 algorithm for authentication.

hmac-md5: Uses HMAC-MD5 algorithm for authentication.

key-id: Authentication key ID of the interface, in the range 1 to 255. It must be the same as that of the peer.

cipher: Uses cipher text.

plain: Uses plain text.

password2: Password string, case sensitive. If you specify neither the cipher nor the plain keyword, it is a string of 1 to 16 characters in plain text or a string of 24 characters in cipher text. For the plain mode, it is a string of 1 to 16 characters. For the cipher mode, it can be either a string of 1 to 16 characters in plain text, or a string of 24 characters in cipher text.

Description

Use the sham link command to configure a sham link.

Use the undo sham link command with no optional keyword to remove a sham link.

Use the undo sham link command with optional keywords to restore the defaults of the parameters for a sham link.

If two PEs belong to the same AS and a backdoor link is present, a sham link can be established between them.

For plain text authentication, the default authentication key type is plain. For authentication using MD5 algorithm or HMAC-MD5 algorithm, the default authentication key type is cipher.

Examples

# Create a sham link with the source address of 1.1.1.1 and the destination address of 2.2.2.2.

<Sysname> system-view

[Sysname] ospf

[Sysname-ospf-1] area 0

[Sysname-ospf-1-area-0.0.0.1] sham-link 1.1.1.1 2.2.2.2

1.1.56 tnl-policy (VPN instance view)

Syntax

tnl-policy tunnel-policy-name

undo tnl-policy

View

VPN instance view

Default Level

2: System level

Parameters

tunnel-policy-name: Name of the tunneling policy for the VPN instance.

Description

Use the tnl-policy command to associate the current VPN instance with a tunneling policy.

Use the undo tnl-policy command to remove the association.

When selecting tunnels from the VPN tunnel management module, an application can use the tunneling policy as the criterion. With no tunneling policy associated with a VPN instance, the default tunneling policy is used.

Related commands: tunnel select-seq load-balance-number.

Examples

# Associate VPN instance vpn2 with tunneling policy po1.

<Sysname> system-view

[Sysname] tunnel-policy po1

[Sysname-tunnel-policy-po1] tunnel select-seq lsp load-balance-number 1

[Sysname-tunnel-policy-po1] quit

[Sysname] ip vpn-instance vpn2

[Sysname-vpn-instance-vpn2] route-distinguisher 22:33

[Sysname-vpn-instance-vpn2] tnl-policy po1

1.1.57 tunnel-policy

Syntax

tunnel-policy tunnel-policy-name

undo tunnel-policy tunnel-policy-name

View

System view

Default Level

2: System level

Parameters

tunnel-policy-name: Name for the tunneling policy.

Description

Use the tunnel-policy command to establish a tunneling policy and enter tunneling policy view.

Use the undo tunnel-policy command to delete a tunneling policy.

Related commands: tunnel select-seq load-balance-number.

Examples

# Establish a tunneling policy named po1 and enter tunneling policy view.

<Sysname> system-view

[Sysname] tunnel-policy po1

[Sysname-tunnel-policy-po1]

1.1.58 tunnel select-seq load-balance-number

Syntax

tunnel select-seq { cr-lsp | lsp } * load-balance-number number

undo tunnel select-seq

View

Tunneling policy view

Default Level

2: System level

Parameters

cr-lsp: Specifies CR-LSP tunnels.

lsp: Specifies LSP tunnels.

number: Number of tunnels for load balancing, one by default.

Description

Use the tunnel select-seq load-balance-number command to configure the preference order for tunnel selection and the number of tunnels for load balancing.

Use the undo tunnel select-seq command to restore the default.

Note that:

l Only tunnels of the types specified in the tunnel select-seq load-balance-number command can be used.

l A tunnel type closer to the select-seq keyword has a higher priority.

l The number of tunnels for load balancing refers to the number of tunnels that an application can use.

By default, one LSP tunnel can be used. That is, only LSP tunnels can be used and the number of tunnels for load balancing is 1.

Examples

# Define a tunneling policy, specifying that only CR-LSP tunnels can be used and the number of tunnels for load balancing be 2.

<Sysname> system-view

[Sysname] tunnel-policy po1

[Sysname-tunnel-policy-po1] tunnel select-seq cr-lsp load-balance-number 2

1.1.59 vpn-instance-capability simple

Syntax

vpn-instance-capability simple

undo vpn-instance-capability

View

OSPF multi-instance view

Default Level

2: System level

Parameters

None

Description

Use the vpn-instance-capability simple command to enable multi-VPN-instance CE.

Use the undo vpn-instance-capability command to disable the function.

By default, the function is disabled.

Examples

# Enable multi-VPN-instance CE.

<Sysname> system-view

[Sysname] ospf 100 vpn-instance vpna

[Sysname-ospf-100] vpn-instance-capability simple

1.1.60 vpn-target (VPN instance view)

Syntax

vpn-target vpn-target &<1-8> [ both | export-extcommunity | import-extcommunity ]

undo vpn-target { all | { vpn-target &<1-8> [ both | export-extcommunity | import-extcommunity ] }

View

VPN instance view

Default Level

2: System level

Parameters

vpn-target&<1-8>: Adds the VPN target extended community attribute to the import or export VPN target extended community list and specify the VPN target in the format nn:nn or IP-address:nn. &<1-8> means that you can specify this argument for up to 8 times.

A VPN target attribute can be in either of these two formats:

l 16-bit AS number:32-bit user-defined number. For example, 101:3.

l 32-bit IP address:16-bit user-defined number. For example, 192.168.122.15:1.

both: Specifies both the export routing information to the destination VPN extended community and the import routing information from the destination VPN extended community. This is the default.

export-extcommunity: Specifies the export routing information to the destination VPN extended community.

import-extcommunity: Specifies the import routing information from the destination VPN extended community.

all: Specifies all export routing information to the destination VPN extended community and import routing information from the destination VPN extended community.

Description

Use the vpn-target command to associate the current VPN instance with one or more VPN targets.

Use the undo vpn-target command to remove the association of the current VPN instance with VPN targets.

VPN target has no default. You must configure it when creating a VPN instance.

Examples

# Associate the current VPN instance with VPN targets.

<Sysname> system-view

[Sysname] ip vpn-instance vpn1

[Sysname-vpn-instance-vpn1] vpn-target 3:3 export-extcommunity

[Sysname-vpn-instance-vpn1] vpn-target 4:4 import-extcommunity

[Sysname-vpn-instance-vpn1] vpn-target 5:5 both

H3C S9500 Command Manual-Release2132[V2.03]-05 MPLS VPN Volume

1.1 MPLS L3VPN Configuration Commands

1.1.1 debugging vrffib

1.1.3 default local-preference (BGP-VPNv4 subaddress family view)

1.1.4 default med (BGP-VPNv4 subaddress family view)

1.1.5 description (VPN instance view)

1.1.11 display bgp vpnv4 route-distinguisher routing-table

1.1.14 display fib statistics vpn-instance

1.1.15 display fib vpn-instance

1.1.21 filter-policy export (BGP-VPNv4 subaddress family view)

1.1.22 filter-policy import (BGP-VPNv4 subaddress family view)

1.1.23 import route-policy

1.1.25 ip vpn-instance

1.1.27 peer advertise-community (BGP-VPNv4 subaddress family view)

1.1.29 peer as-path-acl (BGP-VPNv4 subaddress family view)

1.1.32 peer filter-policy (BGP-VPNv4 subaddress family view)

1.1.35 peer label-route-capability (BGP view/BGP VPN instance view)

1.1.36 peer next-hop-invariable (BGP-VPNv4 subaddress family view)

1.1.37 peer next-hop-local

1.1.38 peer public-as-only (BGP-VPNv4 subaddress family view)

1.1.39 peer reflect-client

1.1.41 peer upe

1.1.44 reflector culster-id

1.1.45 refresh bgp vpn-instance

1.1.51 route-distinguisher (VPN instance view)

1.1.54 rr-filter

1.1.56 tnl-policy (VPN instance view)

1.1.57 tunnel-policy

1.1.58 tunnel select-seq load-balance-number

1.1.59 vpn-instance-capability simple

1.1.60 vpn-target (VPN instance view)

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

News & Events

Contact Us