Login
- Table of Contents
-
- H3C S5500-SI Series Ethernet Switches Command Manual(V1.01)
- 00-1Cover
- 01-Login Commands
- 02-VLAN Commands
- 03-IP Addressing and IP Performance Commands
- 04-QinQ-BPDU TUNNEL Commands
- 05-Port Correlation Commands
- 06-Link Aggregation Commands
- 07-MAC Address Table Management Commands
- 08-Port Security Commands
- 09-MSTP Commands
- 10-IPv6 Commands
- 11-IP Routing Overview Commands
- 12-IPv4 Routing Commands
- 13-IPv6 Routing Commands
- 14-Multicast Commands
- 15-802.1x-HABP-MAC Authentication Commands
- 16-AAA RADIUS HWTACACS Commands
- 17-ARP Commands
- 18-DHCP Commands
- 19-ACL Commands
- 20-QoS Commands
- 21-Port Mirroring Commands
- 22-UDP Helper Commands
- 23-Cluster Management Commands
- 24-SNMP-RMON Commands
- 25-NTP Commands
- 26-DNS Commands
- 27-File System Management Commands
- 28-Information Center Commands
- 29-System Maintaining and Debugging Commands
- 30-NQA Commands
- 31-SSH Commands
- 32-Track Commands
- 33-PoE Commands
- 34-SSL-HTTPS Commands
- 35-PKI Commands
- 36-Stack Management Commands
- 37-Appendix
- Related Documents
-
| Title | Size | Download |
|---|---|---|
| H3C S5500-SI Series Ethernet Switches Command Manual(V1.01) | 3 MB |
Manual Version
20071208-C-1.01
Product Version
This manual is for S5500 series Ethernet switches that are of two software versions and thus only applies to the two software versions. To avoid confusion caused by software version, make sure this manual matches the software version of your product.
This manual applies to the following products:
S5500-SI series Ethernet switches, Release1207
S5500-20TP-SI Ethernet switches, Release1301
Organization
H
Part | Contents |
1 Login | Introduces the commands used for logging into an Ethernet switch. |
2 VLAN | Introduces the commands used for configuring VLAN. |
3 IP Address and IP Performance | Introduces the commands used for configuring IP address and IP performance. |
4 QinQ-BPDU TUNNEL | Introduces the commands used for configuring QinQ. |
5 Port Correlation | Introduces the commands used for configuring link aggregation and port isolation. |
6 Link Aggregation | Introduces the commands used for link aggregation. |
7 MAC Address Table Management | Introduces the commands used for configuring MAC address forwarding table. |
8 Port Security | Introduces the commands used for port security. |
9 MSTP | Introduces the commands used for configuring MSTP. |
10 IPv6 | Introduces the commands used for configuring IPv6 application. |
11 IP Routing Overview | Introduces the commands of Routing Overview. |
12 IPv4 Routing | Introduces the commands used for configuring IPv4 routing, static routing, RIP, and route policy. |
13 IPv6 Routing | Introduces IPv6 routing related configurations, such as static routing, RIPng, and route policy. Introduces the commands used for configuring IPv6 routing, static routing, RIPng, and route policy. |
14 Multicast | Introduces the commands used for configuring IGMP Snooping. |
15 802.1x-HABP-MAC Authentication | Introduces the commands used for 802.1x, HABP and MAC related configurations. |
16 AAA-RADIUS-HWTACACS | Introduces the commands used for AAA, RADIUS, HWTACACS, and the related configurations. |
17 ARP | Introduces the commands used for configuring ARP. |
18 DHCP | Introduces the commands used for DHCP and the related configuration. |
19 ACL | Introduces the commands used for configuring ACL. |
20 QoS | Introduces the commands used for configuring QoS. |
21 Port Mirroring | Introduces the commands used for configuring port mirroring. |
22 UDP Helper | Introduces the commands used for UDP Helper and the related configuration. |
23 Cluster Management | Introduces the commands used for configuring cluster. |
24 SNMP-RMON | Introduces the commands used for the configuration to manage network devices through SNMP and RMON. |
25 NTP | Introduces the commands used for configuring NTP. |
26 DNS | Introduces the commands used for configuring DNS. |
27 File System Management | Introduces the commands used for file system management. |
28 Information Center | Introduces the commands used for the configuration to analyze and diagnose networks using the information center. |
29 System Maintaining and Debugging | Introduces the commands used for daily system maintenance and debugging. |
30 NQA | Introduces the commands used for configuring NQA. |
31 SSH | Introduces the commands used for configuring SSH2.0. |
32 Track | Introduces the commands used for configuring Track. |
33 PoE | Introduces the commands used for configuring PoE and PoE profile. |
34 SSL-HTTPS | Introduces the commands used for configuring SSL and HTTPS. |
35 PKI | Introduces the commands used for configuring PKI. |
36 Stack Management | Introduces the commands used for configuring Stack Management. |
37 Command Index | Lists all the commands in this command manual, which are arranged alphabetically. |
