Contents

4 Hardware management and maintenance· 4-1

Displaying hardware information about the device· 4-1

Displaying software and hardware version information about the device· 4-1

Displaying the operational statistics about the device· 4-1

Displaying information about the device· 4-2

Displaying electrical label information for the device· 4-3

Displaying the CPU usage of the device· 4-3

Displaying the memory usage of the device· 4-4

Displaying the operational status of the built-in fans· 4-4

Displaying the operating state of power modules· 4-5

Rebooting the device· 4-5

Restrictions and guidelines· 4-5

Configuration procedure· 4-6

 

4 Hardware management and maintenance

The command lines and outputs depend on the software version that runs on the device.

Displaying hardware information about the device

Displaying software and hardware version information about the device

Use the display version command to display software and hardware version information about the device. The output includes the following information:

·     Current software version.

·     Current hardware version.

·     Device operating time.

The output depends on the software and hardware version of the device.

<H3C> display version

H3C Comware Software, Version 7.1.064, ESS 5610

Copyright (c) 2004-2022 New H3C Technologies Co., Ltd. All rights reserved.

H3C WX2880X uptime is 4 weeks, 0 days, 0 hours, 46 minutes

Last reboot reason : User soft reboot

 

Boot image: flash:/boot.bin

Boot image version: 7.1.064, ESS 5610

  Compiled May 20 2022 15:00:00

System image: flash:/system.bin

System image version: 7.1.064, ESS 5610

  Compiled May 20 2022 15:00:00

 

with 1 2200MHz Multi-core Processor

4096M bytes DDR4

7456M bytes EMMC Memory

 

Hardware Version is Ver.A

CPLD Version is 002

Basic Bootrom Version is 1.08

Extend Bootrom Version is 1.08

[Subslot 0]WX2880X Hardware Version is Ver.A

Displaying the operational statistics about the device

When you perform routine maintenance or the system fails, you might need to display the operational information of each feature module to locate failures. Typically, you need to run the display commands individually. However, you can use the display diagnostic-information command in any view to display or save the operational statistics of multiple feature modules of the device. This command displays the output of the display clock, display version, display device, and display current-configuration commands.

·     Save the operational statistics for each feature module of the device:

<H3C>display diagnostic-information

Save or display diagnostic information (Y=save, N=display)? [Y/N]:y

Please input the file name(*.tar.gz)[flash:/diag_H3C_20220713-091818.tar.gz]:

Diagnostic information is outputting to flash:/diag_H3C_20220713-091818.tar.gz.

Please wait...

Save successfully.

To view the contents of the default.diag file, execute the more default.diag command in user view, and then press the Page Up and Page Down keys.

·     Display the operational statistics for each feature module of the device. (Details not shown.)

<H3C> display diagnostic-information

Save or display diagnostic information (Y=save, N=display)? [Y/N]:n

===============================================

  ===============display clock===============

09:18:31 UTC Wed 07/13/2022

=================================================

  ===============display version===============

H3C Comware Software, Version 7.1.064, ESS 5610

Copyright (c) 2004-2022 New H3C Technologies Co., Ltd. All rights reserved.

H3C WX2880X uptime is 4 weeks, 0 days, 0 hours, 47 minutes

Last reboot reason : User soft reboot

 

Boot image: flash:/boot.bin

Boot image version: 7.1.064, ESS 5610

  Compiled May 20 2022 15:00:00

System image: flash:/system.bin

System image version: 7.1.064, ESS 5610

  Compiled May 20 2022 15:00:00

 

with 1 2200MHz Multi-core Processor

4096M bytes DDR4

7456M bytes EMMC Memory

 

Hardware Version is Ver.A

…

Displaying information about the device

Use the display device command to display information about the device.

<H3C> display device

Slot No.  Subslot No. Board Type        Status    Max Ports

1         0           WX2880X           Normal      12

Table4-1 Command output

Field	Description
Board Type	Device type.
Status	Device status: ·     Fault—The device is faulty and cannot start up correctly. ·     Normal—The device is operating correctly.
Max Ports	Maximum number of ports supported.

 

Displaying electrical label information for the device

An electrical label is a profile of a device. It contains the permanent configuration, including the serial number, manufacturing date, MAC address, and vendor name.

Use the display device manuinfo command to display the electrical label information for the device.

<H3C> display device manuinfo

DEVICE_NAME:WX2880X

DEVICE_SERIAL_NUMBER:219801A3TM8216E00001

MAC_ADDRESS:5CA7-21EE-F860

MANUFACTURING_DATE:2022-01-14

VENDOR_NAME:H3C

Table4-2 Command output

Field	Description
DEVICE_NAME	Device model.
DEVICE_SERIAL_NUMBER	Serial number of the device.
MAC_ADDRESS	MAC address of the device.
MANUFACTURING_DATE	Manufacturing data of the device.
VENDOR_NAME	Vendor name.

 

Displaying the CPU usage of the device

Use the display cpu-usage command to display the CPU usage statistics for the device.

<H3C> display cpu-usage

Unit CPU usage:

       3% in last 5 seconds

       3% in last 1 minute

       3% in last 5 minutes

Table4-3 Command output

Field	Description
3% in last 5 seconds	Average CPU usage in the last 5 seconds (after the device boots, the device calculates and records the average CPU usage at the interval of 5 seconds).
3% in last 1 minute	Average CPU usage in the last minute (after the device boots, the device calculates and records the average CPU usage at the interval of 1 minute).
3% in last 5 minutes	Average CPU usage in the last 5 minutes (after the device boots, the device calculates and records the average CPU usage at the interval of 5 minutes).

 

Displaying the memory usage of the device

Use the display memory command to display the memory usage statistics for the device.

<H3C>display memory

Memory statistics are measured in KB:

Slot 1:

             Total      Used      Free    Shared   Buffers    Cached   FreeRatio

Mem:       4027756    712064   3315692         0      9836    287052       82.8%

-/+ Buffers/Cache:    415176   3612580

Swap:           0         0         0

                                          

Table4-4 Command output

Field	Description
Mem	Memory usage information.
Total	Total size of the physical memory space that can be allocated.
Used	Used physical memory.
Free	Free physical memory.
Shared	Physical memory shared by processes.
Buffers	Physical memory used for buffers.
Cached	Used physical memory for cache.
FreeRatio	Free memory ratio.
–/+ Buffers/Cache	·     -/+ Buffers/Cache:used = Mem:Used – Mem:Buffers – Mem:Cached, which indicates the physical memory used by applications. ·     -/+ Buffers/Cache:free = Mem:Free + Mem:Buffers + Mem:Cached, which indicates the physical memory available for applications.
Swap	Swap memory.

 

Displaying the operational status of the built-in fans

Use the display fan command to display the operating states of fans.

<H3C> display fan

Fan 1 State: Normal

Table4-5 Command output

Field	Description
Fan n	Fan No..
State	Fan state: ·     Normal—The fan is operating correctly. ·     Absent—The fan is not in position.

 

Displaying the operating state of power modules

Use the display power command to display the operating state of power modules.

<H3C> display power

Power 1 State: Normal

Power 2 State: Abnormal

Table4-6 Command output

Field	Description
Power 1,2	Power module No..
State	Power module state: ·     Normal—The power module is operating correctly. ·     Absent—The power module is not in position.

 

 

Rebooting the device

To reboot the device, use one of the following methods:

·     Reboot the device at the CLI. You can remotely reboot the device in either of the following ways:

¡     Reboot the device immediately by using the reboot command.

¡     Schedule a reboot to occur at a specific time or date or after a delay by using the schedule reboot command.

·     Power off and power on the device. This method cuts off the power of the device forcibly, which might cause data loss. It is the least-preferred method.

Restrictions and guidelines

·     Before you reboot the device, perform the following tasks:

¡     Use the save command to save the running configuration. For more information about the save command, see configuration file management commands in the command references.

¡     Use the display startup and display boot-loader commands to verify that you have specified the correct next-startup configuration files and startup software images. If the main startup software image is corrupt or does not exist, a reboot failure will occur. To avoid a reboot failure, use the boot-loader file command to specify a new startup software image. For more information about the display startup and display boot-loader commands, see software upgrade commands in the command references.

·     The device will not reboot if a file is being accessed.

Configuration procedure

Rebooting the device immediately

Task	Command	Remarks
Reboot the device immediately.	reboot [ force ]	Available in user view.

 

Scheduling a reboot for the device

Task	Command	Remarks
Schedule a reboot.	·     Schedule a reboot to occur at a specific time or date: schedule reboot at time [ date ] ·     Schedule a reboot to occur after a delay: schedule reboot delay time	Use either command. By default, no reboot date or time or reboot delay time is specified. Available in user view. The most recent configuration takes effect if you execute the scheduler reboot at or scheduler reboot delay command multiple times.