Dynamic ARP entry check disables a device from supporting dynamic ARP entries with multicast MAC addresses. The device cannot learn dynamic ARP entries containing multicast MAC addresses. You cannot manually add static ARP entries that contain multicast MAC addresses.

When dynamic ARP entry check is disabled, ARP entries containing multicast MAC addresses are supported. The device can learn dynamic ARP entries containing multicast MAC addresses obtained from the ARP packets sourced from a unicast MAC address. You can also manually add static ARP entries containing multicast MAC addresses.

Examples

# Enable dynamic ARP entry check.

<Sysname> system-view

[Sysname] arp check enable

arp check log enable

Use arp check log enable to enable the ARP logging feature.

Use undo arp check log enable to disable the ARP logging feature.

Syntax

arp check log enable

undo arp check log enable

Default

ARP logging is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

This feature enables a device to log ARP events when ARP cannot resolve IP addresses correctly. The device can log the following ARP events:

· On a proxy ARP-disabled interface, the target IP address of a received ARP packet is not one of the following IP addresses:

¡ The IP address of the receiving interface.

¡ The virtual IP address of the VRRP group.

¡ The public IP address after NAT.

· The sender IP address of a received ARP reply conflicts with one of the following IP addresses:

¡ The IP address of the receiving interface.

¡ The virtual IP address of the VRRP group.

¡ The public IP address after NAT.

The device sends ARP log messages to the information center. You can use the info-center source command to specify the log output rules for the information center. For more information about information center, see Network Management and Monitoring Configuration Guide.

The device can generate a large number of ARP logs. To conserve system resources, enable ARP logging only when you are auditing or troubleshooting ARP events.

Examples

# Enable ARP logging.

<Sysname> system-view

[Sysname] arp check log enable

arp ip-unnumbered learning enable

Use arp ip-unnumbered learning enable to enable an IP unnumbered interface to learn ARP entries for different subnets.

Use undo arp ip-unnumbered learning enable to disable an IP unnumbered interface from learning ARP entries for different subnets.

Syntax

arp ip-unnumbered learning enable

undo arp ip-unnumbered learning enable

Default

An IP unnumbered interface cannot learn ARP entries for different subnets.

Views

Interface view

Predefined user roles

network-admin

Usage guidelines

An IP unnumbered interface cannot learn the ARP entry of the peer device if the unnumbered interface and the peer device are on different subnets. To ensure communication between them, you can enable this feature on the IP unnumbered interface.

This feature takes effect only on an interface configured with the ip address unnumbered command. This interface is an unnumbered interface and borrows the IP address from another interface.

If an IP unnumbered interface is disabled from learning ARP entries for different subnets, existing ARP entries learned for different subnets are deleted after they age out.

Examples

# Configure Ten-GigabitEthernet 3/1/1 to borrow the IP address of Ten-GigabitEthernet 3/1/2, and enable Ten-GigabitEthernet 3/1/1 to learn ARP entries for different subnets.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/1/1

[Sysname-Ten-GigabitEthernet3/1/1] ip address unnumbered interface Ten-GigabitEthernet 3/1/2

[Sysname-Ten-GigabitEthernet3/1/1] arp ip-unnumbered learning enable

Related commands

ip address unnumbered

arp local-conflict record enable

Use arp local-conflict record enable to enable recording conflicts between an endpoint and the local device.

Use undo arp local-conflict record enable to disable recording conflicts between the endpoints and local device.

Syntax

arp local-conflict record enable

undo arp local-conflict record enable

Default

Recording conflicts between the endpoints and local device is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

This feature enables the device to detect and record conflicts between the endpoints and local device. The device determines that a conflict occurs if an incoming non-gratuitous ARP packet has the same sender IP address or sender MAC address as that of the device. The device generates an endpoint and local device conflict entry, logs the conflict, and sends the log to the information center. For information about the log destination and output rule configuration, see information center configuration in Network Management and Monitoring Configuration Guide.

If no new endpoint and local device conflict occurs within three minutes after the entry is generated, the system deletes the conflict entry.

An interface sends only one endpoint and local device conflict log to the information center per minute. The device supports a maximum of 128 interfaces sending conflict logs simultaneously. When the number of interfaces that send conflict logs reaches 128, the device stops another interface from sending conflict logs until an existing conflict is resolved.

Examples

# Enable recording conflicts between the endpoints and local device.

<Sysname> system-view

[Sysname] arp local-conflict record enable

arp max-learning-num

Use arp max-learning-num to set the dynamic ARP learning limit on an interface.

Use undo arp max-learning-num to restore the default.

Syntax

arp max-learning-num max-number

undo arp max-learning-num

Default

An interface can learn a maximum of 589824 dynamic ARP entries.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

VXLAN VSI interface view

VLAN interface view

Predefined user roles

network-admin

Parameters

max-number: Specifies the maximum number of dynamic ARP entries that can be learned on an interface. The value range is 0 to 589824.

Usage guidelines

An interface can dynamically learn ARP entries. To prevent an interface from holding too many ARP entries, you can set the maximum number of dynamic ARP entries that the interface can learn. When the limit is reached, the interface stops learning ARP entries.

When the learning limit is set to 0, the interface is disabled from learning dynamic ARP entries.

Examples

# Specify VLAN-interface 40 to learn a maximum of 10 dynamic ARP entries.

<Sysname> system-view

[Sysname] interface vlan-interface 40

[Sysname-Vlan-interface40] arp max-learning-num 10

# Specify Ten-GigabitEthernet 3/1/1 to learn a maximum of 10 dynamic ARP entries.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/1/1

[Sysname-Ten-GigabitEthernet3/1/1] arp max-learning-num 10

# Specify Layer 2 aggregate interface Bridge-Aggregation 1 to learn a maximum of 10 dynamic ARP entries.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] arp max-learning-num 10

# Specify Layer 3 aggregate interface Route-Aggregation 1 to learn a maximum of 10 dynamic ARP entries.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] arp max-learning-num 10

arp max-learning-number

Use arp max-learning-number to set the dynamic ARP learning limit on a device.

Use undo arp max-learning-number to restore the default.

Syntax

In standalone mode:

arp max-learning-number max-number slot slot-number [ cpu cpu-number ]

undo arp max-learning-number slot slot-number [ cpu cpu-number ]

In IRF mode:

arp max-learning-number max-number chassis chassis-number slot slot-number [ cpu cpu-number ]

undo arp max-learning-number chassis chassis-number slot slot-number [ cpu cpu-number ]

Default

The device can learn a maximum of 589824 dynamic ARP entries.

Views

System view

Predefined user roles

network-admin

Parameters

max-number: Specifies the maximum number of dynamic ARP entries that can be learned on a device. The value range is 0 to 589824..

slot slot-number: Specifies a card by its slot number. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. (In IRF mode.)

cpu cpu-number: Specifies a CPU by its number. This option is available only if multiple CPUs are available on the specified slot.

Usage guidelines

A device can dynamically learn ARP entries. To prevent a device from holding too many ARP entries, you can set the maximum number of dynamic ARP entries that the device can learn. When the limit is reached, the device stops learning ARP entries.

When the learning limit is set to 0, the device is disabled from learning dynamic ARP entries.

Examples

# Set the ARP learning limit to 64 for slot 1.

<Sysname> system-view

[Sysname] arp max-learning-number 64 slot 1

arp safe-guard enable

Only the following cards support this feature:

CSPEX-1304X, CSPEX-1404X, CSPEX-1502X, CSPEX-1504X, CSPEX-1504XA, CSPEX-1602X, CSPEX-1602XA, CSPEX-1804X, CSPEX-1512X, CSPEX-1612X, CSPEX-1812X, RX-SPE200, CEPC-XP4LX, CEPC-XP24LX, CEPC-XP48RX, CEPC-CP4RX, CEPC-CP4RXA, CEPC-CP4RX-L, CSPEX-1802X, CSPEX-1802XA, CSPEX-1812X-E, CSPEX-2304X-G, CEPC-CQ8L, CEPC-CQ8LA, CEPC-CQ16L1, CSPEX-1502XA, RX-SPE200-E

Use arp safe-guard enable to enable the ARP safe-guard feature.

Use undo safe-guard enable to disable the ARP safe-guard feature.

Syntax

arp safe-guard enable

undo arp safe-guard enable

Default

The ARP safe-guard feature is disabled.

Views

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

VLAN interface view

Predefined user roles

network-admin

Usage guidelines

You can use this command to prevent traffic-intensive ARP packet attacks on a device. After you enable this feature, the device operates as follows:

· The device sends replies to all incoming ARP requests but do not generate corresponding ARP entries, which prevents gateway spoofing attacks.

· The device generates ARP entries for incoming ARP replies that the device requests.

· The device drops incoming ARP replies that are not requested by the device, which ensures that the device can learn correct ARP entries.

Examples

# Enable the ARP safe-guard feature on Ten-GigabitEthernet 3/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/1/1

[Sysname-Ten-GigabitEthernet3/1/1] arp safe-guard enable

arp smooth

Use arp smooth to synchronize ARP entries from the active MPU to all other cards.

Syntax

arp smooth

Views

User view

Predefined user roles

network-admin

Usage guidelines

This command triggers a one-time operation to ensure that all cards on the device have the same ARP entries.

To synchronize ARP entries across all cards in a timely manner, you can schedule the device to automatically execute the arp smooth command. For information about scheduling a task, see Fundamentals Configuration Guide.

Examples

# Synchronize ARP entries from the active MPU to all other cards.

<Sysname> arp smooth

arp static

Use arp static to configure a static ARP entry.

Use undo arp to delete an ARP entry.

Syntax

arp static ip-address mac-address [ vlan-id interface-type interface-number | interface-type interface-number interface-type interface-number | vsi-interface vsi-interface-id tunnel number vsi vsi-name | vsi-interface vsi-interface-id interface-type interface-number service-instance instance-id vsi vsi-name ] [ vpn-instance vpn-instance-name ] [ description text ]

undo arp ip-address [ vpn-instance-name ]

Default

No static ARP entries exist.

Views

System view

Predefined user roles

network-admin

Parameters

ip-address: Specifies an IP address for the static ARP entry.

mac-address: Specifies a MAC address for the static ARP entry, in the format of H-H-H.

vlan-id: Specifies the ID of a VLAN to which the static ARP entry belongs. The value range is 1 to 4094.

interface-type interface-number: Specifies an interface by its type and number.

vsi-interface vsi-interface-id: Specifies a VSI interface by its number. The value range for the vsi-interface-id argument is 1 to 31.

tunnel number: Specifies a tunnel interface by its number.

vsi vsi-name: Specifies a VSI by its name, a case-sensitive string of 1 to 31 characters.

service-instance instance-id: Specifies an Ethernet service instance by its ID in the range of 1 to 4096. This option is a must if you specify a Layer 2 Ethernet interface for the preceding interface-type interface-number arguments. Do not specify this option if you specify an interface of other types for the preceding interface-type interface-number argument.

vpn-instance vpn-instance-name: Specifies the MPLS L3VPN instance to which the static ARP entry belongs. The vpn-instance-name argument is a case-sensitive string of 1 to 31 characters. If the static ARP entry belongs to the public network, do not specify this option.

description text: Specifies the description for the static ARP entry, a case-sensitive string of 1 to 255 characters.

Usage guidelines

A static ARP entry is manually configured and maintained. It does not age out and cannot be overwritten by any dynamic ARP entry.

Static ARP entries can be short or long.

A resolved short static ARP entry becomes unresolved upon certain events, for example, when the resolved output interface goes down, or the corresponding VLAN or VLAN interface is deleted.

Long static ARP entries are effective or ineffective. Ineffective long static ARP entries cannot be used for packet forwarding. A long static ARP entry is ineffective when any of the following conditions exists:

· The IP address in the entry conflicts with a local IP address.

· No local interface has an IP address in the same subnet as the IP address in the ARP entry.

If you specify the vlan-id interface-type interface-number argument, follow these restrictions and guidelines:

· The interface can be an Ethernet interface or an aggregate interface.

· The VLAN and VLAN interface must already exist. The specified Ethernet interface must belong to the specified VLAN.

· The IP address of the VLAN interface and the IP address specified by the ip-address argument must be on the same network.

· A long static ARP entry for a VLAN is deleted if the VLAN or VLAN interface is deleted.

On a PE-agg device that provides L2VPN access to the L3VPN network, an L3VE interface (input interface) might be connected to multiple L2VE subinterfaces (output interfaces). In this case, to configure a long static ARP entry, you must specify the interface-type interface-number interface-type interface-number argument to identify the mapping between input and output interfaces. For more information about L2VE interfaces and L3VE interfaces, see MPLS Configuration Guide.

On a VXLAN IP gateway that forwards traffic among VXLANs through VXLAN tunnels, a VSI interface can act as the gateway for multiple VXLANs. The VSI interface (input interface) might be connected to multiple VXLAN tunnel interfaces (output interfaces). In this case, you must specify the vsi-interface vsi-interface-id tunnel number vsi vsi-name parameters to identify a VSI interface-VSI-VXLAN tunnel interface binding. For more information about VSI interfaces, VSI, and VXLAN tunnel interfaces, see VXLAN Configuration Guide.

On a VXLAN IP gateway that forwards traffic from multiple local sites to remote sites, a VSI interface can act as the gateway for multiple local sites. The VSI interface (input interface) might be associated with multiple Ethernet services (output interfaces) on Layer 2 Ethernet interfaces through which the VSI interface connects to the local sites. In this case, you must specify the vsi-interface vsi-interface-id interface-type interface-number service-instance instance-id vsi vsi-name parameters to identify a VSI interface-Layer 2 Ethernet interface-Ethernet service instance-VSI binding. For more information about VSI interfaces, VSI, and Ethernet service instances, see VXLAN Configuration Guide.

For easy identification of ARP entries, you can configure a description for each static ARP entry.

Examples

# Configure a long static ARP entry that contains IP address 202.38.10.2, output interface Ten-GigabitEthernet 3/1/1 in VLAN 10, and MAC address 00e0-fc01-0000.

<Sysname> system-view

[Sysname] arp static 202.38.10.2 00e0-fc01-0000 10 ten-gigabitethernet 3/1/1

# Configure a long static ARP entry that contains IP address 1.1.1.1, MAC address 00e0-fc01-0000, input interface VE-L3VPN 1, and output interface VE-L2VPN 1.1.

<Sysname> system-view

[Sysname] arp static 1.1.1.1 00e0-fc01-0000 ve-l3vpn 1 ve-l2vpn 1.1

# Configure a long static ARP entry that contains IP address 1.1.1.1, MAC address 00e0-fc01-0000, input interface VSI-interface 1, output interface Tunnel 1, and VSI a.

<Sysname> system-view

[Sysname] arp static 1.1.1.1 00e0-fc01-0000 vsi-interface 1 tunnel 1 vsi a

# Configure a long static ARP entry that contains IP address 1.1.1.1, MAC address 00e0-fc01-0000, input interface VSI-interface 1, output interface Ethernet instance 1 on Ten-GigabitEthernet 3/1/1, and VSI a.

<Sysname> system-view

[Sysname] arp static 1.1.1.1 00e0-fc01-0000 vsi-interface 1 ten-gigabitethernet 3/1/1 service-instance 1 vsi a

Related commands

display arp

reset arp

arp timer aging

Use arp timer aging to set the aging timer for dynamic ARP entries.

Use undo arp timer aging to restore the default.

Syntax

arp timer aging aging-time

undo arp timer aging

Default

The aging timer for dynamic ARP entries is 20 minutes.

Views

System view

Predefined user roles

network-admin

Parameters

aging-time: Specifies the aging timer for dynamic ARP entries, in the range of 1 to 1440 minutes.

Usage guidelines

Each dynamic ARP entry in the ARP table has a limited lifetime, called an aging timer. The aging timer of a dynamic ARP entry is reset each time the dynamic ARP entry is updated. Dynamic ARP entries that are not updated before their aging timers expire are deleted from the ARP table.

Set the aging timer for dynamic ARP entries as needed. For example, when you configure proxy ARP, set a short aging time so that invalid dynamic ARP entries can be deleted in a timely manner.

Examples

# Set the aging timer for dynamic ARP entries to 10 minutes.

<Sysname> system-view

[Sysname] arp timer aging 10

Related commands

display arp timer aging

arp user-ip-conflict record enable

Use arp user-ip-conflict record enable to enable recording user IP address conflicts.

Use undo arp user-ip-conflict record enable to disable recording user IP address conflicts.

Syntax

arp user-ip-conflict record enable

undo arp user-ip-conflict record enable

Default

Recording user IP address conflicts is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

This feature enables the device to detect and record user IP address conflicts. The device determines that a conflict occurs if an incoming ARP packet has the same sender IP address as an existing ARP entry but a different sender MAC address. The device generates a user IP address conflict record, logs the conflict, and sends the log to the information center. For information about the log destination and output rule configuration, see the information center in Network Management and Monitoring Configuration Guide.

A card can generate a maximum of 10 user IP address conflict records or logs per second and save a maximum of 200 user IP address conflict records or logs.

If the maximum number of saved user IP address conflict records or logs is reached, a new record or log will override the earliest record or log.

To display user IP address conflict records, use the display arp user-ip-conflict record command.

Examples

# Enable recording user IP address conflicts.

<Sysname> system-view

[Sysname] arp user-ip-conflict record enable

Related commands

display arp user-ip-conflict record

arp user-move record enable

Use user-move record enable to enable recording user port migrations.

Use undo arp user-move record enable to disable recording user port migrations.

Syntax

arp user-move record enable

undo arp user-move record enable

Default

Recording user port migrations is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

Each card can generate a maximum of 10 user port migration logs per second.

To display user port migration records, use the display arp user-move record command.

Examples

# Enable recording user port migration.

<Sysname> system-view

[Sysname] arp user-move record enable

Related commands

display arp user-move record

display arp

Use display arp to display ARP entries.

Syntax

In standalone mode:

In IRF mode:

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

all: Displays all ARP entries.

dynamic: Displays dynamic ARP entries.

static: Displays static ARP entries.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays ARP entries on the active MPU. (In standalone mode.)

cpu cpu-number: Specifies a CPU by its number. This option is available only if multiple CPUs are available on the specified slot.

vlan vlan-id: Specifies a VLAN by its VLAN ID. The VLAN ID is in the range of 1 to 4094.

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays ARP entries for all interfaces.

verbose: Displays detailed information about ARP entries.

Usage guidelines

This command displays information about static and dynamic ARP entries, including the IP address, MAC address, VLAN ID, output interface, entry type, and aging timer.

Examples

# Display all ARP entries.

<Sysname> display arp all

Type: S-Static D-Dynamic O-Openflow R-Rule M-Multiport I-Invalid

IP address MAC address VLAN/VSI name Interface Aging Type

1.1.1.1 02e0-f102-0023 1 XGE3/1/1 -- S

1.1.1.2 00e0-fc00-0001 12 XGE3/1/2 16 D

1.1.1.3 00e0-fe50-6503 vsi1 Tunnel1 15 D

1.1.1.4 000d-88f7-9f7d vsi1 XGE3/1/3 16 D

1.1.1.5 000c-77f7-8e1c -- L3VE1000-L2VE1000.1 16 D

# Display detailed information about all ARP entries.

<Sysname> display arp all verbose

IP address : 1.1.1.1 MAC address : 02e0-f102-0023

Type : Static Aging : --

Interface : XGE3/1/1

SVLAN/CVLAN : 1000/1001

VPN instance : --

Link ID : --

VXLAN ID : --

VSI name : --

VSI interface : --

Nickname : 0x0000

Description : User1

IP address : 1.1.1.2 MAC address : 0015-e944-adc5

Type : Dynamic Aging : 16 min

Interface : XGE3/1/2

SVLAN/CVLAN : --/--

VPN instance : --

Link ID : --

VXLAN ID : --

VSI name : --

VSI interface : --

Nickname : 0x0000

Description : --

IP address : 1.1.1.5 MAC address : 0015-e944-adc5

Type : Dynamic Aging : 16 min

Interface : L3VE1000-L2VE1000.1

SVLAN/CVLAN : --/--

VPN instance : --

Link ID : --

VXLAN ID : --

VSI name : --

VSI interface : --

Nickname : 0x0000

Description : --

# Display the number of all ARP entries.

<Sysname> display arp all count

Total number of entries : 4

Table 1 Command output

Field	Description
IP address	IP address in an ARP entry.
MAC address	MAC address in an ARP entry.
VLAN/VSI name	ID of the VLAN or name of the VSI to which an ARP entry belongs. This field displays hyphens (--) in either of the following situations: · The ARP entry is an unresolved short static ARP entry. · The output interface of the ARP entry does not belong to any VLAN or VSI.
Interface	Output interface in an ARP entry. This field displays hyphens (--) in either of the following situations: · The ARP entry is an unresolved short static ARP entry. · The ARP entry is a multiport ARP entry and has no output interface information. To obtain the output interface information of the multiport ARP entry, look up the MAC address table according to the MAC address in the ARP entry.
Aging	Aging time for an ARP entry, in minutes. For a static ARP entry, this field always displays hyphens (--). The static ARP entry never ages out unless you delete it manually. For a dynamic ARP entry, this field displays hyphens (--) if the aging time is unknown.
Type	ARP entry type: · D—Dynamic. · S—Static. · O—OpenFlow. · R—Rule. · M—Multiport. · I—Invalid.
SVLAN/CVLAN	ID of the SVLAN or CVLAN to which the ARP entry belongs. This field displays hyphens (--) in either of the following situations: · The ARP entry is an unresolved short static ARP entry. · The output interface of the ARP entry does not belong to any SVLAN or CVLAN.
VPN instance	Name of VPN instance. This field displays hyphens (--) if no VPN instance is configured for the ARP entry.
Link ID	Link ID in an ARP entry. This field displays hyphens (--) if the ARP entry does not belong to any VSI.
VXLAN ID	VXLAN ID (also called VNI). This field displays hyphens (--) if the ARP entry does not belong to any VXLAN.
VSI name	Name of the VSI to which the ARP entry belongs. This field displays hyphens (--) if the ARP entry does not belong to a specific VSI.
VSI interface	VSI interface specified for the VSI. This field displays hyphens (--) if no VSI interface is specified for the VSI.
Nickname	Nickname of the ARP entry. The nickname is a string of four hexadecimal numbers, for example, 012a.
Description	Description of the ARP entry. If no description is configured for the ARP entry, this field displays hyphens (--).
Total number of entries	Number of ARP entries.

Related commands

arp static

reset arp

display arp entry-limit

Use display arp entry-limit to display the maximum number of ARP entries that a device supports.

Syntax

display arp entry-limit

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display the maximum number of ARP entries that the device supports.

<Sysname> display arp entry-limit

ARP entries: 2048

display arp ip-address

Use display arp ip-address to display the ARP entry for an IP address.

Syntax

In standalone mode:

display arp ip-address [ slot slot-number [ cpu cpu-number ] ] [ verbose ]

In IRF mode:

display arp ip-address [ chassis chassis-number slot slot-number [ cpu cpu-number ] ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ip-address: Specifies an IP address.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays the ARP entry on the active MPU. (In standalone mode.)

cpu cpu-number: Specifies a CPU by its number. This option is available only if multiple CPUs are available on the specified slot.

verbose: Displays the detailed information about the specified ARP entry.

Usage guidelines

The ARP entry information includes the IP address, MAC address, VLAN ID, output interface, entry type, and aging timer.

Examples

# Display the ARP entry for the IP address 20.1.1.1.

<Sysname> display arp 20.1.1.1

Type: S-Static D-Dynamic O-Openflow R-Rule M-Multiport I-Invalid

IP address MAC address VLAN/VSI name Interface Aging Type

20.1.1.1 00e0-fc00-0001 -- -- -- S

Related commands

arp static

reset arp

display arp safe-guard statistics

Only the following cards support this feature:

Use display arp safe-guard statistics to display ARP safe-guard statistics.

Syntax

In standalone mode:

display arp safe-guard statistics slot slot-number

In IRF mode:

display arp safe-guard statistics chassis chassis-number slot slot-number

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies a card by its slot number. (In standalone mode.)

Examples

# Display ARP safe-guard statistics.

<Sysname> display arp safe-guard statistics

ARP replies sent by the driver: 1234

ARP replies dropped by the driver: 100

Table 2 Command output

Field	Description
ARP replies sent by the driver	Number of ARP replies that the driver sent to the device.
ARP replies dropped by the driver	Number of illegal ARP replies that the driver dropped.

Related commands

arp safe-guard enable

reset arp safe-guard statistics

display arp timer aging

Use display arp timer aging to display the aging timer of dynamic ARP entries.

Syntax

display arp timer aging

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display the aging timer of dynamic ARP entries.

<Sysname> display arp timer aging

Current ARP aging time is 20 minute(s)(default)

Related commands

arp timer aging

display arp user-ip-conflict record

Use display arp user-ip-conflict record to display user IP address conflict records.

Syntax

In standalone mode:

display arp user-ip-conflict record [ slot slot-number [ cpu cpu-number ] ]

In IRF mode:

display arp user-ip-conflict record [ chassis chassis-number slot slot-number [ cpu cpu-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays user IP address conflict records on all cards. (In standalone mode.)

cpu cpu-number: Specifies a CPU by its number. This option is available only if multiple CPUs are available on the specified slot.

Examples

# Display all user IP address conflict records.

<Sysname> display arp user-ip-conflict record

IP address: 10.1.1.1

System time: 2018-02-02 11:22:29

Conflict count: 1

Log suppress count: 0

Old interface: Ten-GigabitEthernet3/1/1

New interface: Ten-GigabitEthernet3/1/2

Old SVLAN/CVLAN: 100/2

New SVLAN/CVLAN: 100/2

Old MAC: 00e0-ca63-8141

New MAC: 00e0-ca63-8142

IP address: 10.1.1.2

System time: 2018-02-02 10:20:30

Conflict count: 1

Log suppress count: 0

Old interface: Ten-GigabitEthernet3/1/1

New interface: Ten-GigabitEthernet3/1/2

Old SVLAN/CVLAN: 100/--

New SVLAN/CVLAN: 100/--

Old MAC: 00e0-ca63-8141

New MAC: 00e0-ca63-8142

Table 3 Command output

Field	Description
IP address	IP address of a user.
System time	Time when the user IP address conflict occurred.
Conflict count	Number of times that conflicts for the IP address.
Log suppress count	Number of times that user IP address conflict logs are suppressed.
Old interface	Output interface in the old ARP entry.
New interface	Output interface in the new ARP entry.
Old SVLAN/CVLAN	ID of the outer VLAN or inner VLAN in the old ARP entry. This field displays hyphens (--) if the ARP entry does not belong to any outer VLAN or inner VLAN.
New SVLAN/CVLAN	ID of the outer VLAN or inner VLAN in the new ARP entry. This field displays hyphens (--) if the ARP entry does not belong to any outer VLAN or inner VLAN.
Old MAC	MAC address in the old ARP entry.
New MAC	MAC address in the new ARP entry.

‌

Related commands

arp user-ip-conflict record enable

display arp user-move record

Use display arp user-move record to display user port migration records.

Syntax

In standalone mode:

display arp user-move record [ slot slot-number [ cpu cpu-number ] ]

In IRF mode:

display arp user-move record [ chassis chassis-number slot slot-number [ cpu cpu-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays user port migration records on all cards. (In standalone mode.)

cpu cpu-number: Specifies a CPU by its number. This option is available only if multiple CPUs are available on the specified slot.

Usage guidelines

Each card can save a maximum of 200 user port migration records.

When the number of user port migration records reaches the upper limit, new records will overwrite the earliest ones.

Examples

# Display all user port migration records.

<Sysname> display arp user-move record

IP address: 10.1.1.1

MAC address: 0001-0201-0e81

System time: 2018-02-02 11:22:29

Move count: 1

Log suppress count: 0

Before:

interface: Ten-GigabitEthernet3/1/1

SVLAN/CVLAN: 100/2

After:

interface: Ten-GigabitEthernet3/1/2

SVLAN/CVLAN: 100/2

IP address: 10.1.1.2

MAC address: 0001-0201-0e82

System time: 2018-02-02 10:20:30

Move count: 1

Log suppress count: 0

Before:

interface: Ten-GigabitEthernet3/1/1

SVLAN/CVLAN: 100/--

After:

interface: Ten-GigabitEthernet3/1/2

SVLAN/CVLAN: 100/--

Table 4 Command output

Field	Description
IP address	IP address of the user.
MAC address	MAC address of the user.
System time	Time when the user port migration occurred.
Move count	Number of times that user port migrated.
Log suppress count	Number of times that the generation of user port migration logs is suppressed.
Interface	Output interface in the ARP entry.
SVLAN/CVLAN	ID of the outer VLAN or inner VLAN in the ARP entry. This field displays hyphens (--) if the ARP entry does not belong to any outer VLAN or inner VLAN.

Related commands

arp user-move record enable

display arp vpn-instance

Use display arp vpn-instance to display the ARP entries for a VPN instance.

Syntax

display arp vpn-instance vpn-instance-name [ count ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters.

Usage guidelines

This command displays information about ARP entries for a VPN instance, including the IP address, MAC address, VLAN ID, output interface, entry type, and aging timer.

Examples

# Display ARP entries for VPN instance test.

<Sysname> display arp vpn-instance test

Type: S-Static D-Dynamic O-Openflow R-Rule M-Multiport I-Invalid

IP address MAC address VLAN/VSI name Interface Aging Type

20.1.1.1 00e0-fc00-0001 -- -- -- S

Related commands

arp static

reset arp

Use reset arp to clear ARP entries from the ARP table.

Syntax

In standalone mode:

reset arp { all | dynamic | interface interface-type interface-number | slot slot-number [ cpu cpu-number ] | static }

In IRF mode:

reset arp { all | chassis chassis-number slot slot-number [ cpu cpu-number ] | dynamic | interface interface-type interface-number | static }

Views

User view

Predefined user roles

network-admin

Parameters

all: Clears all ARP entries.

dynamic: Clears all dynamic ARP entries.

static: Clears all static ARP entries.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command clears ARP entries on the active MPU. (In standalone mode.)

cpu cpu-number: Specifies a CPU by its number. This option is available only if multiple CPUs are available on the specified slot.

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command clears ARP entries on all interfaces.

Usage guidelines

CAUTION:

The reset arp command clears existing ARP entries on the device. It might cause external traffic unable to quickly reach the LAN users.

‌

Examples

# Clear all static ARP entries.

<Sysname> reset arp static

This will delete all static entries. Continue? [Y/N]:

Related commands

arp static

display arp

reset arp safe-guard statistics

Only the following cards support this feature:

Use reset arp safe-guard statistics to clear ARP safe-guard statistics.

Syntax

In standalone mode:

reset arp safe-guard statistics { all | slot slot-number }

In IRF mode:

reset arp safe-guard statistics { all | chassis chassis-number slot slot-number }

Views

User view

Predefined user roles

network-admin

Parameters

all: Specifies all ARP safe-guard statistics.

slot slot-number: Specifies a card by its slot number. (In standalone mode.)

Examples

# Clear ARP safe-guard statistics.

<Sysname> reset arp safe-guard statistics all

Related commands

arp safe-guard enable

display arp safe-guard statistics

Gratuitous ARP commands

arp ip-conflict log prompt

Use arp ip-conflict log prompt to enable IP conflict notification.

Use undo arp ip-conflict log prompt to restore the default.

Syntax

arp ip-conflict log prompt

undo arp ip-conflict log prompt

Default

IP conflict notification is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

By default, the device performs the following operations if it is using the sender IP address of a received ARP packet:

· Sends a gratuitous ARP request.

· Displays an error message after the device receives an ARP reply about the conflict.

You can use this command to enable the device to display error messages before sending a gratuitous ARP reply or request for conflict confirmation.

Examples

# Enable IP conflict notification on the device.

<Sysname> system-view

[Sysname] arp ip-conflict log prompt

arp send-gratuitous-arp

Use arp send-gratuitous-arp to enable periodic sending of gratuitous ARP packets on an interface.

Use undo arp send-gratuitous-arp to disable the interface from periodically sending gratuitous ARP packets.

Syntax

arp send-gratuitous-arp [ interval interval ]

undo arp send-gratuitous-arp

Default

Periodic sending of gratuitous ARP packets is disabled.

Views

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

VSI interface view

VLAN interface view

Predefined user roles

network-admin

Parameters

interval interval: Specifies the sending interval in the range of 200 to 200000 milliseconds. The default value is 2000 milliseconds.

Usage guidelines

This feature takes effect on an interface only when the interface has an IP address and the data link layer state of the interface is up.

This feature can send gratuitous ARP requests only for a VRRP virtual IP address, or the sending interface's primary IP address or manually configured secondary IP address. The primary IP address can be configured manually or automatically, whereas the secondary IP address must be configured manually.

If you change the sending interval for gratuitous ARP packets, the configuration takes effect at the next sending interval.

The sending interval for gratuitous ARP packets might be much longer than the set interval when any of the following conditions exist:

· This feature is enabled on multiple interfaces.

· Each interface is configured with multiple secondary IP addresses.

· A small sending interval is configured in the preceding cases.

Examples

# Enable Ten-GigabitEthernet 3/1/1 to send gratuitous ARP packets every 300 milliseconds.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/1/1

[Sysname-Ten-GigabitEthernet3/1/1] arp send-gratuitous-arp interval 300

gratuitous-arp-learning enable

Use gratuitous-arp-learning enable to enable learning of gratuitous ARP packets.

Use undo gratuitous-arp-learning enable to disable learning of gratuitous ARP packets.

Syntax

gratuitous-arp-learning enable

undo gratuitous-arp-learning enable

Default

Learning of gratuitous ARP packets is enabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

The learning of gratuitous ARP packets feature allows a device to maintain its ARP table by creating or updating ARP entries based on received gratuitous ARP packets.

When this feature is disabled, the device uses received gratuitous ARP packets to update existing ARP entries only. ARP entries are not created based on the received gratuitous ARP packets, which saves ARP table space.

Examples

# Enable learning of gratuitous ARP packets.

<Sysname> system-view

[Sysname] gratuitous-arp-learning enable

gratuitous-arp-sending enable

Use gratuitous-arp-sending enable to enable sending gratuitous ARP packets upon receiving ARP requests whose sender IP address is on a different subnet.

Use undo gratuitous-arp-sending enable to disable sending gratuitous ARP packets upon receiving ARP requests whose sender IP address is on a different subnet.

Syntax

gratuitous-arp-sending enable

undo gratuitous-arp-sending enable

Default

A device does not send gratuitous ARP packets when it receives ARP requests whose sender IP address is on a different subnet.

Views

System view

Predefined user roles

network-admin

Examples

# Disable a device from sending gratuitous ARP packets upon receiving ARP requests whose sender IP address is on a different subnet.

<Sysname> system-view

[Sysname] undo gratuitous-arp-sending enable

gratuitous-arp mac-change retransmit

Use gratuitous-arp mac-change retransmit to set the times and the interval for retransmitting a gratuitous ARP packet for the device MAC address change.

Use undo gratuitous-arp mac-change retransmit to restore the default.

Syntax

gratuitous-arp mac-change retransmit times interval seconds

undo gratuitous-arp mac-change retransmit

Default

The device sends a gratuitous packet for its MAC address change once only.

Views

System view

Predefined user roles

network-admin

Parameters

times: Specifies the times of retransmitting a gratuitous packet, in the range of 1 to 10.

interval seconds: Specifies the interval for retransmitting a gratuitous packet, in the range of 1 to 10 seconds.

Usage guidelines

The device sends a gratuitous ARP packet to inform other devices of its MAC address change. However, the other devices might fail to receive the packet because the device sends the gratuitous ARP packet once only by default. Use this command to configure gratuitous ARP retransmission parameters to ensure that the other devices can receive the packet.

After you execute this command, the device will retransmit a gratuitous ARP packet for its MAC address change at the specified interval for the specified times.

Examples

# Set the times to 3 and the interval to 5 for retransmitting a gratuitous ARP packet for the device MAC address change.

<Sysname> system-view

[Sysname] gratuitous-arp mac-change retransmit 3 interval 5

Proxy ARP commands

display local-proxy-arp

Use display local-proxy-arp to display the local proxy ARP status.

Syntax

display local-proxy-arp [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays the local proxy ARP status for all interfaces.

Usage guidelines

You can use this command to check whether local proxy ARP is enabled or disabled.

Examples

# Display the local proxy ARP status for Ten-GigabitEthernet 3/1/1.

<Sysname> display local-proxy-arp interface ten-gigabitethernet 3/1/1

Interface Ten-GigabitEthernet3/1/1

Local Proxy ARP status: enabled

Related commands

local-proxy-arp enable

display proxy-arp

Use display proxy-arp to display the proxy ARP status.

Syntax

display proxy-arp [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays the proxy ARP status for all interfaces.

Usage guidelines

You can use this command to check whether proxy ARP is enabled or disabled.

Examples

# Display the proxy ARP status on Ten-GigabitEthernet 3/1/1.

<Sysname> display proxy-arp interface ten-gigabitethernet 3/1/1

Interface Ten-GigabitEthernet3/1/1

Proxy ARP status: disabled

Related commands

proxy-arp enable

local-proxy-arp enable

Use local-proxy-arp enable to enable local proxy ARP.

Use undo local-proxy-arp enable to disable local proxy ARP.

Syntax

local-proxy-arp enable [ ip-range start-ip-address to end-ip-address ]

undo local-proxy-arp enable

Default

Local proxy ARP is disabled.

Views

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

VSI interface view

VLAN interface view

L3VE interface/subinterface view

Predefined user roles

network-admin

Parameters

ip-range start-ip-address to end-ip-address: Specifies the IP address range for which local proxy ARP is enabled. The start IP address must be lower than or equal to the end IP address.

Usage guidelines

Proxy ARP enables a device on a network to answer ARP requests for an IP address not on that network.

With proxy ARP, hosts in different broadcast domains can communicate with each other as they do on the same network. To allow communication between hosts that connect to the same Layer 3 interface and reside in different broadcast domains, enable local proxy ARP.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Enable local proxy ARP on Ten-GigabitEthernet 3/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/1/1

[Sysname-Ten-GigabitEthernet3/1/1] local-proxy-arp enable

# Enable local proxy ARP on Ten-GigabitEthernet 3/1/1 for an IP address range.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/1/1

[Sysname-Ten-GigabitEthernet3/1/1] local-proxy-arp enable ip-range 1.1.1.1 to 1.1.1.20

Related commands

display local-proxy-arp

proxy-arp enable

Use proxy-arp enable to enable common proxy ARP.

Use undo proxy-arp enable to disable common proxy ARP.

Syntax

proxy-arp enable

undo proxy-arp enable

Default

Common proxy ARP is disabled.

Views

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

VSI interface view

VLAN interface view

L3VE interface/subinterface view

Predefined user roles

network-admin

Usage guidelines

Proxy ARP enables a device on a network to answer ARP requests for an IP address not on that network.

With proxy ARP, hosts in different broadcast domains can communicate with each other as they do on the same network. To allow communication between hosts that connect to different Layer 3 interfaces or Layer 3 subinterfaces and reside in different broadcast domains, enable common proxy ARP.

Examples

# Enable common proxy ARP on Ten-GigabitEthernet 3/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/1/1

[Sysname-Ten-GigabitEthernet3/1/1] proxy-arp enable

Related commands

display proxy-arp

proxy-arp inter-vlan enable

Use proxy-arp inter-vlan enable to enable inter-VLAN proxy ARP.

Use undo proxy-arp inter-vlan enable to disable inter-VLAN proxy ARP.

Syntax

proxy-arp inter-vlan enable

undo proxy-arp inter-vlan enable

Default

Inter-VLAN proxy ARP is disabled.

Views

Layer 3 Ethernet subinterface view

Layer 3 aggregate subinterface view

L3VE subinterface view

Predefined user roles

network-admin

Usage guidelines

Proxy ARP enables a device on a network to answer ARP requests for an IP address not on that network.

With proxy ARP, hosts in different broadcast domains can communicate with each other as they do on the same network. To allow communication between hosts that connect to the same Layer 3 subinterface but reside in different VLANs, enable inter-VLAN proxy ARP.

Examples

# Enable inter-VLAN proxy ARP on Layer 3 Ethernet subinterface Ten-GigabitEthernet 3/1/1.1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/1/1.1

[Sysname-Ten-GigabitEthernet3/1/1.1] proxy-arp inter-vlan enable

ARP snooping commands

arp snooping enable

Use arp snooping enable to enable ARP snooping.

Use undo arp snooping enable to disable ARP snooping.

Syntax

arp snooping enable

undo arp snooping enable

Default

ARP snooping is disabled.

Views

VLAN view

Predefined user roles

network-admin

Examples

# Enable ARP snooping for VLAN 2.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2] arp snooping enable

display arp snooping

Use display arp snooping to display ARP snooping entries.

Syntax

In standalone mode:

display arp snooping [ vlan vlan-id ] [ slot slot-number [ cpu cpu-number ] ] [ count ]

display arp snooping ip ip-address [ slot slot-number [ cpu cpu-number ] ]

In IRF mode:

display arp snooping [ vlan vlan-id ] [ chassis chassis-number slot slot-number [ cpu cpu-number ] ] [ count ]

display arp snooping ip ip-address [ chassis chassis-number slot slot-number [ cpu cpu-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vlan vlan-id: Displays ARP snooping entries for a VLAN. The vlan-id argument is in the range of 1 to 4094.

ip ip-address: Displays the ARP snooping entry for the specified IP address.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays ARP snooping entries on the active MPU. (In standalone mode.)

cpu cpu-number: Specifies a CPU by its number. This option is available only if multiple CPUs are available on the specified slot.

Examples

# Display ARP snooping entries for VLAN 2.

<Sysname> display arp snooping vlan 2

IP Address MAC Address VLAN ID Interface Aging Status

3.3.3.3 0003-0003-0003 2 XGE3/1/1 20 Valid

3.3.3.4 0004-0004-0004 2 XGE3/1/2 5 Invalid

# Display the number of the ARP snooping entries.

<Sysname> display arp snooping count

Total entries: 2

Table 5 Command output

Field	Description
IP Address	IP address in an ARP snooping entry.
MAC Address	MAC address in an ARP snooping entry.
VLAN ID	ID of the VLAN to which the ARP snooping entry belongs.
Interface	Input interface in an ARP snooping entry.
Aging	Aging time for an ARP snooping entry in minutes. If the card learns an ARP snooping entry from another card, the card cannot learn the aging time of the entry, and this field displays hyphens (--).
Status	Status of an ARP snooping entry: Valid, Invalid, Collision.
Total entries	Number of ARP snooping entries.

Related commands

reset arp snooping

Use reset arp snooping to delete ARP snooping entries.

Syntax

reset arp snooping [ ip ip-address | vlan vlan-id ]

Views

User view

Predefined user roles

network-admin

Parameters

ip ip-address: Deletes the ARP snooping entry for the specified IP address.

vlan vlan-id: Deletes ARP snooping entries for the specified VLAN. The value range for the vlan-id argument is 1 to 4094.

Usage guidelines

If you do not specify any option, the command deletes all ARP snooping entries.

Examples

# Delete ARP snooping entries for VLAN 2.

<Sysname> reset arp snooping vlan 2

Related commands

display arp snooping

ARP suppression commands

arp suppression enable

Use arp suppression enable to enable ARP suppression.

Use undo arp suppression enable to disable ARP suppression.

Syntax

arp suppression enable

undo arp suppression enable

Default

ARP suppression is disabled.

Views

Cross-connect view

Predefined user roles

network-admin

Usage guidelines

You must enable L2VPN before you enter cross-connect view.

Examples

# Enable ARP suppression for cross-connect 2 in cross-connect group 1.

<Sysname> system-view

[Sysname] xconnect-group 1

[Sysname-xcg-1] connection 2

[Sysname-xcg-1-2] arp suppression enable

Related commands

arp suppression push interval

Use arp suppression push interval to enable the ARP suppression push feature and set a push interval.

Use undo arp suppression push interval to disable the ARP suppression push feature.

Syntax

arp suppression push interval interval

undo arp suppression push interval

Default

The ARP suppression push feature is disabled.

Views

System view

Predefined user roles

network-admin

Parameters

interval: Specifies a push interval for ARP suppression, in the range of 1 to 1440 minutes.

Usage guidelines

The ARP suppression push feature regularly pushes ARP suppression entries by broadcasting gratuitous ARP packets.

Examples

# Configure the device to push ARP suppression entries every 2 minutes.

<Sysname> system-view

[Sysname] arp suppression push interval 2

Related commands

arp suppression enable

display arp suppression xconnect-group

Use display arp suppression xconnect-group to display ARP suppression entries.

Syntax

In standalone mode:

display arp suppression xconnect-group [ name group-name ] [ slot slot-number [ cpu cpu-number ] ] [ count ]

In IRF mode:

display arp suppression xconnect-group [ name group-name ] [ chassis chassis-number slot slot-number [ cpu cpu-number ] ] [ count ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

name group-name: Specifies a cross-connect group by its name, a case-sensitive string of 1 to 31 characters excluding hyphens (-). If you do not specify a cross-connect group, this command display ARP suppression entries for all cross-connect groups.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays ARP suppression entries on the active MPU. (In standalone mode.)

cpu cpu-number: Specifies a CPU by its number. This option is available only if multiple CPUs are available on the specified slot.

Examples

# Display ARP suppression entries for all cross-connect groups.

<Sysname> display arp suppression xconnect-group

IP address MAC address Xconnect-group Connection Aging

100.1.1.1 000c-29fe-5a8f vpna svc 12

100.1.1.2 000c-29fe-5aa3 vpna svc 25

# Display the total number of ARP suppression entries.

<Sysname> display arp suppression xconnect-group count

Total entries: 2

Table 6 Command output

Field	Description
IP address	IP address in the ARP suppression entry.
MAC address	MAC address in the ARP suppression entry.
Xconnect-group	Name of the cross-connect group to which the ARP suppression entry belongs.
Connection	Name of the cross-connect to which the ARP suppression entry belongs.
Aging	Aging time of the ARP suppression entry, in minutes.

Related commands

reset arp suppression xconnect-group

Use reset arp suppression xconnect-group to clear ARP suppression entries.

Syntax

reset arp suppression xconnect-group [ name group-name ]

Views

User view

Predefined user roles

network-admin

Parameters

name group-name: Specifies a cross-connect group by its name, a case-sensitive string of 1 to 31 characters excluding hyphens (-). If you do not specify a cross-connect group, this command clears ARP suppression entries for all cross-connect groups.

Examples

# Clear ARP suppression entries for all cross-connect groups.

<Sysname> reset arp suppression xconnect-group

Related commands

display arp suppression xconnect-group

ARP direct route advertisement commands

arp route-direct advertise

Use arp route-direct advertise to enable ARP direct route advertisement.

Use undo arp route-direct advertise to disable ARP direct route advertisement.

Syntax

arp route-direct advertise

undo arp route-direct advertise

Default

ARP direct route advertisement is disabled.

Views

System view

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

L3VE interface view

L3VE subinterface view

VPN instance view

FlexE logical interface view

Predefined user roles

network-admin

Usage guidelines

You can enable ARP direct route advertisement in different views.

· In system view, the feature takes effect on all interfaces on the public network.

· In interface view, the feature takes effect on the specified interface.

· In VPN instance view, the feature takes effect on all interfaces that belong to the VPN instance.

To disable ARP direct route advertisement on an interface, you must also disable ARP direct route advertisement in the VPN instance or the public network to which the interface belongs.

Examples

# Enable ARP direct route advertisement in system view.

<Sysname> system-view

[Sysname] arp route-direct advertise

# Enable ARP direct route advertisement on Ten-GigabitEthernet 3/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/1/1

[Sysname-Ten-GigabitEthernet3/1/1] arp route-direct advertise

# Enable ARP direct route advertisement on L3VE interface VE-L3VPN 1.

<Sysname> system-view

[Sysname] interface ve-l3vpn 1

[Sysname-VE-L3VPN1] arp route-direct advertise

# Enable ARP direct route advertisement in VPN instance vpna.

<Sysname> system-view

[Sysname] ip vpn-instance vpna

[Sysname-vpn-instance-vpna] arp route-direct advertise

06-Layer 3—IP Services Command Reference

arp safe-guard enable

arp timer aging

display arp entry-limit

display arp vpn-instance

reset arp

gratuitous-arp-learning enable

display local-proxy-arp

display proxy-arp

local-proxy-arp enable

ARP snooping commands

display arp snooping

reset arp snooping

ARP suppression commands

ARP direct route advertisement commands

Cloud & AI

InterConnect

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Resources

Partner Business Management

Company Information

News & Events

Contact Us