03-Layer 2—LAN Switching Command Reference

HomeSupportResource CenterReference GuidesCommand ReferencesH3C S6520X & S6520-SI & S5560X-HI & S5000-EI & MS4600 Command References-R6615Pxx-6W10103-Layer 2—LAN Switching Command Reference
05-Ethernet link aggregation commands
Title Size Download
05-Ethernet link aggregation commands 229.31 KB

Ethernet link aggregation commands

bandwidth

Use bandwidth to set the expected bandwidth for an interface.

Use undo bandwidth to restore the default.

Syntax

bandwidth bandwidth-value

undo bandwidth

Default

The expected bandwidth (in kbps) is the interface baud rate divided by 1000.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

Predefined user roles

network-admin

Parameters

bandwidth-value: Specifies the expected bandwidth in the range of 1 to 400000000 kbps.

Usage guidelines

The expected bandwidth is an informational parameter used only by higher-layer protocols for calculation. You cannot adjust the actual bandwidth of an interface by using this command.

Examples

# Set the expected bandwidth to 10000 kbps for Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] bandwidth 10000

default

Use default to restore the default settings for an aggregate interface.

Syntax

default

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

Predefined user roles

network-admin

Usage guidelines

CAUTION

CAUTION:

The default command might interrupt ongoing network services. Make sure you are fully aware of the impacts of this command when you execute it on a live network.

 

This command might fail to restore the default settings for some commands for reasons such as command dependencies and system restrictions. Use the display this command in interface view to identify these commands, and then use their undo forms or follow the command reference to restore their default settings. If your restoration attempt still fails, follow the error message instructions to resolve the problem.

Examples

# Restore the default settings for Layer 2 aggregate interface 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] default

description

Use description to configure the description of an interface.

Use undo description to restore the default.

Syntax

description text

undo description

Default

The description of an interface is interface-name Interface. For example, the default description of Bridge-Aggregation 1 is Bridge-Aggregation1 Interface.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

Predefined user roles

network-admin

Parameters

text: Specifies a description, a case-sensitive string of 1 to 255 characters.

Examples

# Configure the description as connect to the lab for Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] description connect to the lab

display interface

Use display interface to display aggregate interface information.

Syntax

display interface [ { bridge-aggregation | route-aggregation } [ interface-number ] ] [ brief [ description | down ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

bridge-aggregation: Specifies Layer 2 aggregate interfaces.

route-aggregation: Specifies Layer 3 aggregate interfaces.

interface-number: Specifies an existing aggregate interface number.

brief: Displays brief interface information. If you do not specify this keyword, the command displays detailed interface information.

description: Displays complete interface descriptions. If you do not specify this keyword, the command displays only the first 25 characters of each interface description.

down: Displays information about interfaces in down state and the causes for the down state. If you do not specify this keyword, the command displays information about interfaces in all states.

Usage guidelines

If you do not specify an aggregate interface type, the command displays information about all interfaces.

If you specify an aggregate interface type but do not specify an interface number, the command displays information about all aggregate interfaces of the specified type.

Examples

# Display detailed information about Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> display interface bridge-aggregation 1

Bridge-Aggregation1

Current state: UP

Line protocol state: UP

IP packet frame type: Ethernet II, hardware address: 000f-e207-f2e0

Description: Bridge-Aggregation1 Interface

Bandwidth: 1000 kbps

Unknown-speed mode, unknown-duplex mode

Link speed type is autonegotiation, link duplex type is autonegotiation

PVID: 1

Port link-type: Access

 Tagged VLANs:   None

 UnTagged VLANs: 1

Last clearing of counters: Never

Last 300 seconds input:  6900 packets/sec 885160 bytes/sec    0%

Last 300 seconds output:  3150 packets/sec 404430 bytes/sec    0%

Input (total):  5364747 packets, 686688416 bytes

         2682273 unicasts, 1341137 broadcasts, 1341337 multicasts, 0 pauses

Input (normal):  5364747 packets, 686688416 bytes

         2682273 unicasts, 1341137 broadcasts, 1341337 multicasts, 0 pauses

Input:  0 input errors, 0 runts, 0 giants, 0 throttles

         0 CRC, 0 frame, 0 overruns, - aborts

         - ignored, - parity errors

Output (total): 1042508 packets, 133441832 bytes

         1042306 unicasts, 0 broadcasts, 202 multicasts, - pauses

Output (normal): 1042508 packets, 133441832 bytes

         1042306 unicasts, 0 broadcasts, 202 multicasts, 0 pauses

Output: 0 output errors, - underruns, - buffer failures

         0 aborts, 0 deferred, 0 collisions, 0 late collisions

         - lost carrier, - no carrier

# Display detailed information about Layer 3 aggregate interface Route-Aggregation 1.

<Sysname> display interface route-aggregation 1

Route-Aggregation1

Current state: UP

Line protocol state: UP

Description: Route-Aggregation1 Interface

Bandwidth: 1000 kbps

Maximum transmission unit: 1500

Internet protocol processing: Disabled

IP packet frame type: Ethernet II, hardware address: 0000-0000-0000

IPv6 packet frame type: Ethernet II, hardware address: 0000-0000-0000

Link speed type is autonegotiation, link duplex type is autonegotiation

Last clearing of counters: Never

Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 drops

0 packets output, 0 bytes, 0 drops

# Display brief information about Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> display interface bridge-aggregation 1 brief

Brief information on interfaces in bridge mode:

Link: ADM - administratively down; Stby - standby

Speed: (a) – auto

Duplex: (a)/A - auto; H - half; F - full

Type: A - access; T - trunk; H - hybrid

Interface            Link Speed     Duplex Type PVID Description

BAGG1                DOWN auto      A      A    1

# Display brief information about Layer 3 aggregate interface Route-Aggregation 1.

<Sysname> display interface route-aggregation 1 brief

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface            Link Protocol Primary IP        Description

RAGG1                UP   UP       --

Table 1 Command output

Field

Description

Bridge-Aggregation1

Layer 2 aggregate interface name.

Route-Aggregation1

Layer 3 aggregate interface name.

Current state

Physical link state of the interface:

·     Administratively DOWN—The interface has been shut down by using the shutdown command.

·     DOWN—The interface is administratively up, but its physical state is down (possibly because no physical link exists or the link has failed).

·     UP—The interface is both administratively and physically up.

IP packet frame type

IPv4 packet framing format.

IPv6 packet frame type

IPv6 packet framing format.

Description

Description of the interface.

Bandwidth

Expected bandwidth of the interface. This field is not displayed when the bandwidth is 0 kbps.

Port priority

Port priority of the interface.

Unknown-speed mode, unknown-duplex mode

The interface speed and duplex mode are unknown.

Port link-type

Port link type:

·     Access.

·     Trunk.

·     Hybrid.

Tagged VLANs

VLAN whose packets are sent out of this interface with a tag.

Untagged VLANs

VLAN whose packets are sent out of this interface without a tag.

Last clearing of counters

Time when the reset counters interface command was last used to clear the interface statistics. This field displays Never if the reset counters interface command has never been used on the interface since device startup.

Last 300 seconds input/output rate

Average input or output rate over the last 300 seconds.

Input/Output (total)

Statistics of all packets received or sent on the interface.

Input/Output (normal)

Statistics of all normal packets received or sent on the interface.

Line protocol state

Data link layer state of the interface:

·     UP.

·     DOWN.

Maximum transmission unit

MTU of the interface.

Internet protocol processing: Disabled

The interface is not assigned an IP address and cannot process IP packets.

Internet address: ip-address/mask-length (Type)

IP address of the interface and type of the address in parentheses.

Possible IP address types include:

·     Primary—Manually configured primary IP address.

·     Sub—Manually configured secondary IP address. If the interface has both primary and secondary IP addresses, the primary IP address is displayed. If the interface has only secondary IP addresses, the lowest secondary IP address is displayed.

·     DHCP-Allocated—DHCP allocated IP address. For more information, see DHCP client configuration in Layer 3IP Services Configuration Guide.

·     Unnumbered—IP address borrowed from another interface.

Brief information on interfaces in route mode

Brief information about Layer 3 interfaces.

Brief information on interfaces in bridge mode

Brief information about Layer 2 interfaces.

Interface

Abbreviated interface name.

Link

Physical link state of the interface:

·     UP—The interface is physically up.

·     DOWN—The interface is physically down.

·     ADM—The interface has been shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command.

Speed

Speed of the interface, in bps.

This field displays the (a) flag next to the speed if the speed is automatically negotiated.

This field displays auto if the interface is configured to autonegotiate its speed but the autonegotiation has not started.

Duplex

Duplex mode of the interface:

·     A—Autonegotiation. The interface is configured to autonegotiate its duplex mode but the autonegotiation has not started.

·     F—Full duplex.

·     F(a)—Autonegotiated full duplex.

·     H—Half duplex.

·     H(a)—Autonegotiated half duplex.

Type

Link type of the interface:

·     A—Access.

·     H—Hybrid.

·     T—Trunk.

Protocol

Data link layer protocol state of the interface:

·     UP—The data link layer protocol of the interface is up.

·     DOWN—The data link layer protocol of the interface is down.

·     UP(s)—The data link layer protocol of the interface is up, but the link is an on-demand link or does not exist. The (s) attribute represents the spoofing flag. This value is typical of null interfaces and loopback interfaces.

Primary IP

Primary IP address of the interface. This field displays two hyphens (--) if the interface does not have an IP address.

Cause

Cause for the physical link state of an interface to be DOWN.

 

display lacp system-id

Use display lacp system-id to display the local system ID.

Syntax

display lacp system-id

Views

Any view

Predefined user roles

network-admin

network-operator

Usage guidelines

You can use the lacp system-priority command to change the LACP priority of the local system. The LACP priority value is specified in decimal format in the lacp system-priority command. However, it is displayed in hexadecimal format in the output from the display lacp system-id command.

Examples

# Display the local system ID.

<Sysname> display lacp system-id

Actor System ID: 0x8000, 0000-fc00-6504

Table 2 Command output

Field

Description

Actor System ID: 0x8000, 0000-fc00-6504

Local system ID, which contains the LACP system priority (0x8000 in this sample output) and the LACP system MAC address (0000-FC00-6504 in this sample output).

 

Related commands

lacp system-priority

display link-aggregation capability

Use display link-aggregation capability to display the link aggregation capability for the device.

Syntax

display link-aggregation capability

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

 

NOTE:

The following CLI output is supported only in the devices as follows:

·     S6520X-HI switch series.

·     S6520X-EI switch series.

·     S6520X-SI switch series (except S6520X-26XC-UPWR-SI or S6520X-54XC-UPWR-SI).

·     S5560X-HI switch series.

·     MS4600 switch series.

·     S6520-26Q-SI.

·     # Display the link aggregation capability for the device.

<Sysname> display link-aggregation capability

Default link aggregation capability:

  Maximum groups: 128

  Maximum Selected ports per group: 8

Current link aggregation capability:

  Maximum groups: 128

  Maximum Selected ports per group: 8

Link aggregation capability at the next reboot:

  Maximum groups: 125

  Maximum Selected ports per group: 16

Supported link aggregation capability list:

  128*8          125*16         61*32

 

NOTE:

The following CLI output is supported only in the devices as follows:

·     S6520-SI switch series (except S6520-26Q-SI).

·     S5000-EI switch series.

·     S6520X-26XC-UPWR-SI.

·     S6520X-54XC-UPWR-SI.

·     # Display the link aggregation capability for the device.

<Sysname> display link-aggregation capability

Default link aggregation capability:

  Maximum groups: 128

  Maximum Selected ports per group: 8

Current link aggregation capability:

  Maximum groups: 128

  Maximum Selected ports per group: 8

Link aggregation capability at the next reboot:

  Maximum groups: 29

  Maximum Selected ports per group: 16

Supported link aggregation capability list:

  61*8          29*16         13*32

Table 3 Command output

Field

Description

Supported link aggregation capability list

Link aggregation capabilities supported by the device. Each item in the list is in the format of maximum number of aggregation groups*maximum number of Selected ports per aggregation group.

 

Related commands

link-aggregation capability

display link-aggregation load-sharing mode

Use display link-aggregation load-sharing mode to display the global link-aggregation load sharing mode.

Syntax

display link-aggregation load-sharing mode

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display the global link-aggregation load sharing mode. This example displays the default setting.

<Sysname> display link-aggregation load-sharing mode

Link-aggregation load-sharing mode:

  Layer 2 traffic:   packet type-based sharing

  Layer 3 traffic:   packet type-based sharing

# Display the global link-aggregation load sharing mode. This example displays a user-configured setting.

<Sysname> display link-aggregation load-sharing mode

Link-aggregation load-sharing mode:

  destination-mac address, source-mac address

Table 4 Command output

Field

Description

Link-aggregation load-sharing mode

Global link-aggregation load sharing mode.

By default, this field displays the link-aggregation load sharing modes for Layer 2 and Layer 3 traffic.

If you have configured the global link-aggregation load sharing mode, this field displays the configured mode.

Layer 2 traffic: packet type-based sharing

Default link-aggregation load sharing mode for Layer 2 traffic. By default, Layer 2 traffic is load shared based on source and destination MAC addresses, source and destination IP addresses, and source and destination port numbers.

Layer 3 traffic: packet type-based sharing

Default link-aggregation load sharing mode for Layer 3 traffic. By default, Layer 3 traffic is load shared based on source and destination MAC addresses, source and destination IP addresses, and source and destination port numbers.

destination-mac address, source-mac address

User-configured link-aggregation load sharing mode. In this sample output, traffic is load shared based on source and destination MAC addresses.

 

display link-aggregation member-port

Use display link-aggregation member-port to display detailed link aggregation information about the specified member ports.

Syntax

display link-aggregation member-port [ interface-list | auto ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-list: Specifies a list of link aggregation member ports, in the format interface-type interface-number1 [ to interface-type interface-number2 ]. The value for the interface-number2 argument must be equal to or greater than the value for the interface-number1 argument.

auto: Specifies all link aggregation member ports that are enabled with automatic assignment.

Usage guidelines

A member port in a static aggregation group cannot obtain information about the peer group. For such member ports, the command displays the port number, port priority, and operational key of only the local end.

Examples

# Display detailed information about Ten-GigabitEthernet 1/0/1, which is a member port of a static aggregation group.

<Sysname> display link-aggregation member-port ten-gigabitethernet 1/0/1

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

       D -- Synchronization, E -- Collecting, F -- Distributing,

       G -- Defaulted, H -- Expired

 

Ten-GigabitEthernet1/0/1:

Aggregate Interface: Bridge-Aggregation1

Port Number: 1

Port Priority: 32768

Oper-Key: 1

# Display detailed information about Ten-GigabitEthernet 1/0/2, which is a member port of a dynamic aggregation group.

<Sysname> display link-aggregation member-port ten-gigabitethernet 1/0/2

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

       D -- Synchronization, E -- Collecting, F -- Distributing,

       G -- Defaulted, H -- Expired

 

Ten-GigabitEthernet1/0/2:

Aggregate Interface: Bridge-Aggregation10

Local:

    Port Number: 2

    Port Priority: 32768

    Oper-Key: 2

    Flag: {ACDEF}

Remote:

    System ID: 0x8000, 000f-e267-6c6a

    Port Number: 26

    Port Priority: 32768

    Oper-Key: 2

    Flag: {ACDEF}

Received LACP Packets: 5 packet(s)

Illegal: 0 packet(s)

Sent LACP Packets: 7 packet(s)

# Display detailed information about all link aggregation member ports that are enabled with automatic assignment.

<Sysname> display link-aggregation member-port auto

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

       D -- Synchronization, E -- Collecting, F -- Distributing,

       G -- Defaulted, H -- Expired

 

Ten-GigabitEthernet1/0/3:

Preference Aggregation Interface: Bridge-Aggregation11

Aggregate Interface: Bridge-Aggregation11

Local:

    Port Number: 3

    Port Priority: 32768

    Oper-Key: 1

    Flag: {ACDEF}

Remote:

    System ID: 0x8000, a057-75a2-0100

    Port Number: 3

    Port Priority: 32768

    Oper-Key: 1

    Flag: {ACDEF}

Received LACP Packets: 3 packet(s)

Illegal: 0 packet(s)

Sent LACP Packets: 6 packet(s)

Table 5 Command output

Field

Description

Flags

LACP state flags. This field is one byte long, represented by ABCDEFGH from the least significant bit to the most significant bit. A letter appears when its bit is 1 and does not appear when its bit is 0.

·     A—Indicates whether LACP is active on the port. 1 indicates active. 0 indicates passive.

·     B—Indicates the LACP timeout interval. 1 indicates the short timeout interval. 0 indicates the long timeout interval.

·     C—Indicates whether the sending system considers that the link is aggregatable. 1 indicates yes. 0 indicates no.

·     D—Indicates whether the sending system considers that the link has been aggregated. 1 indicates yes. 0 indicates no.

·     E—Indicates whether the sending system considers that the link can collect frames. 1 indicates yes. 0 indicates no.

·     F—Indicates whether the sending system considers that the link can distribute frames. 1 indicates yes. 0 indicates no.

·     G—Indicates whether the RX state machine of the sending system is in default state. 1 indicates yes. 0 indicates no.

·     H—Indicates whether the RX state machine of the sending system is in expired state. 1 indicates yes. 0 indicates no.

Aggregate Interface

Aggregate interface to which the member port belongs.

Preferred Aggregate Interface

Aggregate interface to which you prefer to assign the member port during automatic assignment.

Local

Information about the local end.

Oper-key

Operational key.

Flag

LACP protocol state flag.

Remote

Information about the peer end.

System ID

Peer system ID, containing the LACP system priority and the LACP system MAC address.

Received LACP Packets

Total number of LACP packets received.

Illegal

Total number of illegal packets.

Sent LACP Packets

Total number of LACP packets sent.

 

display link-aggregation summary

Use display link-aggregation summary to display brief information about all aggregation groups.

Syntax

display link-aggregation summary

Views

Any view

Predefined user roles

network-admin

network-operator

Usage guidelines

Static link aggregation groups cannot obtain information about the peer groups. As a result, the Partner ID field displays None for a static link aggregation group.

Examples

# Display brief information about all aggregation groups.

<Sysname> display link-aggregation summary

Aggregate Interface Type:

BAGG -- Bridge-Aggregation, BLAGG –- Blade-Aggregation, RAGG -- Route-Aggregation, SCH-B – Schannel-Bundle

Aggregation Mode: S -- Static, D -- Dynamic

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Actor System ID: 0x8000, 000f-e267-6c6a

 

AGG        AGG   Partner ID              Selected  Unselected  Individual  Share

Interface  Mode                          Ports     Ports       Ports       Type

--------------------------------------------------------------------------------

RAGG10     S     None                    1         0           0           NonS

BAGG20     D     0x8000,00e0-fcff-ff01   2         0           0           Shar

Table 6 Command output

Field

Description

Aggregate Interface Type

Aggregate interface type:

·     BAGG—Layer 2.

·     RAGG—Layer 3.

Aggregation Mode

Aggregation group type:

·     S—Static.

·     D—Dynamic.

Loadsharing Type

Load sharing type:

·     Shar—Load-sharing.

·     NonS—Non-load-sharing.

Actor System ID

Local system ID, which contains the local LACP system priority and the local LACP system MAC address.

AGG Interface

Type and number of the aggregate interface.

AGG Mode

Aggregation group type.

Partner ID

System ID of the peer system, which contains the peer LACP system priority and the peer LACP system MAC address.

Selected Ports

Total number of Selected ports.

Unselected Ports

Total number of Unselected ports.

Individual Ports

Total number of Individual ports.

Share Type

Load sharing type.

 

display link-aggregation troubleshooting

Use display link-aggregation troubleshooting to display the aggregation states of aggregation member ports and the reason why a port was placed in Unselected state.

Syntax

display link-aggregation troubleshooting [ { bridge-aggregation | route-aggregation } [ interface-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

bridge-aggregation: Specifies Layer 2 aggregate interfaces.

route-aggregation: Specifies Layer 3 aggregate interfaces.

interface-number: Specifies an existing aggregate interface by its number.

Usage guidelines

If you do not specify an aggregate interface type, the command displays information about all aggregation groups.

If you specify an aggregate interface type but do not specify an interface number, the command displays information about all aggregation groups of the specified type.

You can specify the bridge-aggregation or route-aggregation keyword only when aggregate interfaces of the specified type exist on the device.

Examples

# Display the aggregation states of aggregation member ports for all aggregation groups and the reason why a port was placed in Unselected state.

<Sysname> display link-aggregation troubleshooting

Aggregate Interface: Bridge-Aggregation2

 Member ports:

  XGE1/0/2

   Status: Selected

  XGE1/0/3

   Status: Unselected

   Reason: The physical or line protocol state of the port is down

   Advice: Check the connection

Table 7 Command output

Field

Description

Reason

Reason why the port was placed in Unselected state.

Advice

Recommended action.

 

display link-aggregation verbose

Use display link-aggregation verbose to display detailed information about the aggregation groups that correspond to the specified aggregate interfaces.

Syntax

display link-aggregation verbose [ { bridge-aggregation | route-aggregation } [ interface-number ] ] [ all-configuration ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

bridge-aggregation: Specifies Layer 2 aggregate interfaces.

route-aggregation: Specifies Layer 3 aggregate interfaces.

interface-number: Specifies an existing aggregate interface by its number.

all-configuration: Specifies all member ports in aggregation groups of the specified aggregate interfaces. If you do not specify this option, this command displays detailed information about only member ports on present cards.

Usage guidelines

If you do not specify an aggregate interface type, the command displays detailed information about all aggregation groups.

If you specify an aggregate interface type but do not specify an interface number, the command displays detailed information about all aggregation groups of the specified type.

The bridge-aggregation or route-aggregation keyword is available only when aggregate interfaces of the corresponding type exist on the device.

This command does not display the interfaces that are enabled with automatic assignment if they have not joined an aggregation group.

Examples

# Display detailed information about Layer 2 aggregation group 10, which is a dynamic aggregation group.

<Sysname> display link-aggregation verbose bridge-aggregation 10

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port, M -- Management port, R -- Reference port

Flags:  A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

        D -- Synchronization, E -- Collecting, F -- Distributing,

        G -- Defaulted, H -- Expired

 

Aggregate Interface: Bridge-Aggregation10

Creation Mode: Manual

Aggregation Mode: Dynamic

Loadsharing Type: Shar

Management VLANs: None

System ID: 0x8000, 000f-e267-6c6a

Local:

  Port                Status   Priority Index    Oper-Key               Flag

  XGE1/0/1            S        32768    61       2                      {ACDEF}

  XGE1/0/2            S        32768    62       2                      {ACDEF}

  XGE1/0/3            S        32768    63       2                      {ACDEF}

Remote:

  Actor               Priority Index    Oper-Key SystemID               Flag

  XGE1/0/1(R)         32768    111      2        0x8000, 000f-e267-57ad {ACDEF}

  XGE1/0/2            32768    112      2        0x8000, 000f-e267-57ad {ACDEF}

  XGE1/0/3            32768    113      2        0x8000, 000f-e267-57ad {ACDEF}

# Display detailed information about Layer 2 aggregation group 20, which is a static aggregation group.

<Sysname> display link-aggregation verbose bridge-aggregation 20

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port, M -- Management port, R -- Reference port

Flags:  A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

        D -- Synchronization, E -- Collecting, F -- Distributing,

        G -- Defaulted, H -- Expired

 

Aggregate Interface: Bridge-Aggregation20

Aggregation Mode: Static

Loadsharing Type: Shar

Management VLANs: None

  Port             Status  Priority Oper-Key

  XGE1/0/1(R)      S       32768    1

  XGE1/0/2         S       32768    1

  XGE1/0/3         S       32768    1

Table 8 Command output

Field

Description

Loadsharing Type

Load sharing type:

·     Shar—Load-sharing.

·     NonS—Non-load-sharing.

Port Status

Port state:

·     Selected.

·     Unselected.

·     Individual.

Port

Port type:

·     Auto port—The port is enabled with automatic assignment.

·     Management port—The port is a management port. This value is not supported in the current software version.

·     Reference port—The port is a reference port.

Flags

LACP state flags. This field is one byte long, represented by ABCDEFGH from the least significant bit to the most significant bit. A letter appears when its bit is 1 and does not appear when its bit is 0.

·     A—Indicates whether LACP is active on the port. 1 indicates active. 0 indicates passive.

·     B—Indicates the LACP timeout interval. 1 indicates the short timeout interval. 0 indicates the long timeout interval.

·     C—Indicates whether the sending system considers that the link is aggregatable. 1 indicates yes. 0 indicates no.

·     D—Indicates whether the sending system considers that the link has been aggregated. 1 indicates yes. 0 indicates no.

·     E—Indicates whether the sending system considers that the link can collect frames. 1 indicates yes. 0 indicates no.

·     F—Indicates whether the sending system considers that the link can distribute frames. 1 indicates yes. 0 indicates no.

·     G—Indicates whether the RX state machine of the sending system is in default state. 1 indicates yes. 0 indicates no.

·     H—Indicates whether the RX state machine of the sending system is in expired state. 1 indicates yes. 0 indicates no.

Aggregate Interface

Name of the aggregate interface.

Creation Mode

Creation mode of the dynamic aggregate interface:

·     Auto.

·     Manual.

Aggregation Mode

Aggregation group type:

·     S—Static.

·     D—Dynamic.

Management VLANs

(This field is not supported in the current software version.) Management VLANs.  If no management VLANs are specified, this field displays None.

System ID

Local system ID, containing the local LACP system priority and the local LACP system MAC address.

Local

Information about the local end:

·     Port—Port type and number.

·     Status—Port state, which can be Selected, Unselected, or Individual.

·     Priority—Port priority.

·     Index—Port index.

·     Oper-Key—Operational key.

·     Flag—LACP state flag.

NOTE:

For static aggregation groups, the Index and Flag fields are not displayed.

Remote

Information about the peer end:

·     Actor—Type and number of the local port. This field displays the (R) flag next to the port if its peer port is the reference port.

·     Priority—Priority of the peer port.

·     Index—Index of the peer port.

·     Oper-Key—Operational key of the peer port.

·     System ID—System ID of the peer end.

·     Flag—LACP state flag of the peer end.

 

interface bridge-aggregation

Use interface bridge-aggregation to create a Layer 2 aggregate interface and enter its view, or enter the view of an existing Layer 2 aggregate interface.

Use undo interface bridge-aggregation to delete a Layer 2 aggregate interface.

Syntax

interface bridge-aggregation interface-number

undo interface bridge-aggregation interface-number

Default

No Layer 2 aggregate interfaces exist.

Views

System view

Predefined user roles

network-admin

Parameters

interface-number: Specifies a Layer 2 aggregate interface number. The value range for the interface-number argument is 1 to 1024.

Usage guidelines

When you create a Layer 2 aggregate interface, the system automatically creates a Layer 2 aggregation group with the same number. The aggregation group operates in static aggregation mode by default.

Deleting a Layer 2 aggregate interface also deletes the Layer 2 aggregation group. At the same time, the member ports of the aggregation group, if any, leave the aggregation group.

Examples

# Create Layer 2 aggregate interface Bridge-Aggregation 1, and enter its view.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1]

interface route-aggregation

Use interface route-aggregation to create a Layer 3 aggregate interface or subinterface and enter its view, or enter the view of an existing Layer 3 aggregate interface or subinterface.

Use undo interface route-aggregation to delete a Layer 3 aggregate interface or subinterface.

Syntax

interface route-aggregation { interface-number | interface-number.subnumber }

undo interface route-aggregation { interface-number | interface-number.subnumber }

Default

No Layer 3 aggregate interfaces or subinterfaces exist.

Views

System view

Predefined user roles

network-admin

Parameters

interface-number: Specifies a Layer 3 aggregate interface number. The value range for the interface-number argument is 1 to 1024.

interface-number.subnumber: Specifies a subinterface of a Layer 3 aggregate interface. The interface-number argument specifies the main interface number. The subnumber argument specifies the subinterface number and is separated from the main interface number by a dot (.). The value range for the subnumber argument is 1 to 4094.

Usage guidelines

When you create a Layer 3 aggregate interface, the system automatically creates a Layer 3 aggregation group with the same number. The Layer 3 aggregation group operates in static aggregation mode by default.

Deleting a Layer 3 aggregate interface also deletes the Layer 3 aggregation group and all its aggregate subinterfaces. At the same time, the member ports of the aggregation group, if any, leave the aggregation group.

Deleting a Layer 3 aggregate subinterface does not affect the state of the main interface and the corresponding aggregation group.

Examples

# Create Layer 3 aggregate interface Route-Aggregation 1 and enter its view.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1]

# Create Layer 3 aggregate subinterface Route-Aggregation 1.1 and enter its view.

<Sysname> system-view

[Sysname] interface route-aggregation 1.1

[Sysname-Route-Aggregation1.1]

jumboframe enable

Use jumboframe enable to allow the jumbo frames on an interface to pass through.

Use undo jumboframe enable to deny jumbo frames on an interface.

Use undo jumboframe enable size to restore the default.

Syntax

jumboframe enable [ size ]

undo jumboframe enable [ size ]

Default

An interface allows jumbo frames with a maximum length of 10000 bytes to pass through.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

size: Specifies the maximum length of jumbo frames, in bytes. The value range for this argument is 1536 to 10000.

Usage guidelines

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Allow jumbo frames on Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> System-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] jumboframe enable

lacp default-selected-port disable

Use lacp default-selected-port disable to disable the default port selection action for dynamic aggregation groups.

Use undo lacp default-selected-port disable to enable the default port selection action for dynamic aggregation groups.

Syntax

lacp default-selected-port disable

undo lacp default-selected-port disable

Default

The default port selection action is enabled for dynamic aggregation groups.

Views

System view

Predefined user roles

network-admin

Usage guidelines

The default port selection action applies to dynamic aggregation groups.

This action automatically chooses the port with the lowest ID from among all up member ports as a Selected port if none of them has received LACPDUs before the LACP timeout interval expires.

After this action is disabled, a dynamic aggregation group will not have any Selected ports to forward traffic if it has not received LACPDUs before the LACP timeout interval expires.

Examples

# Disable the default port selection action.

<Sysname> system-view

[Sysname] lacp default-selected-port disable

lacp edge-port

Use lacp edge-port to configure an aggregate interface as an edge aggregate interface.

Use undo lacp edge-port to restore the default.

Syntax

lacp edge-port

undo lacp edge-port

Default

An aggregate interface does not operate as an edge aggregate interface.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

Use this command on the aggregate interface that connects the device to a server if dynamic link aggregation is configured only on the device. This feature improves link reliability by enabling all member ports of the aggregation group to forward packets.

This command takes effect only on an aggregate interface corresponding to a dynamic aggregation group.

Link-aggregation traffic redirection cannot operate correctly on an edge aggregate interface.

Examples

# Configure Layer 2 aggregate interface Bridge-Aggregation 1 as an edge aggregate interface.

<Sysname> System-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] lacp edge-port

lacp mode

Use lacp mode passive to configure LACP to operate in passive mode on a port.

Use undo lacp mode to restore the default.

Syntax

lacp mode passive

undo lacp mode

Default

LACP operates in active mode on a port.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

This command takes effect only on member ports of dynamic aggregation groups.

When LACP is operating in passive mode on a local member port and its peer port, both ports cannot send LACPDUs. When LACP is operating in active mode on either end of a link, both ports can send LACPDUs.

Examples

# Configure LACP to operate in passive mode on Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] lacp mode passive

lacp period short

Use lacp period short to enable the short LACP timeout interval (3 seconds) on an interface.

Use undo lacp period to restore the default.

Syntax

lacp period short

undo lacp period

Default

The LACP timeout interval is the long timeout interval (90 seconds) on an interface.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

To avoid traffic interruption during an ISSU, do not enable the short LACP timeout interval before performing the ISSU. For more information about ISSU, see Fundamentals Configuration Guide.

Examples

# Enable the short LACP timeout interval (3 seconds) on Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] lacp period short

lacp select speed

Use lacp select speed to configure a dynamic aggregation group to use port speed as the prioritized criterion for reference port selection.

Use undo lacp select speed to restore the default.

Syntax

lacp select speed

undo lacp select speed

Default

Port ID is the prioritized criterion for reference port selection in a dynamic aggregation group.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

CAUTION

CAUTION:

Changing reference port selection criteria might cause transient traffic interruption. When you use this command, make sure you understand its impact on your network.

 

This command enables a dynamic aggregation group to select a high-speed member port as the reference port.

You must execute this command at both ends of the aggregate link so the peer aggregation systems use the same criteria for reference port selection.

As a best practice, shut down the peer aggregate interfaces before you execute this command and bring up the interfaces after this command is executed on both of them.

This command takes effect only on dynamic aggregate interfaces. On a static aggregate interface, you can execute this command, but the setting cannot take effect.

Examples

# Specify port speed as the prioritized criterion for reference port selection on Layer 2 dynamic aggregate interface Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation mode dynamic

[Sysname-Bridge-Aggregation1] lacp select speed

lacp system-mac

Use lacp system-mac to set the LACP system MAC address.

Use undo lacp system to restore the default.

Syntax

lacp system-mac mac-address

undo lacp system-mac

Default

The LACP system MAC address is the bridge MAC address of the device.

Views

System view

Predefined user roles

network-admin

Parameters

mac-address: Specifies a MAC address in the format of H-H-H. The MAC address cannot be an all-zero, all-F, or multicast MAC address.

Usage guidelines

All S-MLAG devices must use the same LACP system MAC address.

LACPDUs carry the LACP system MAC address configured by using this command. To identify the LACP system MAC address used by a link aggregation group, examine the System ID field in the output from the display link-aggregation verbose command.

You can configure the LACP system MAC address globally and in aggregate interface view. The global LACP system MAC address takes effect on all aggregation groups, and an aggregate-interface-specific LACP system MAC address takes precedence over the global LACP system MAC address.

On a DR system, DR interfaces in the same DR group must use the same LACP system MAC address.

Examples

# Set the LACP system MAC address to 0001-0001-0001.

<Sysname> system-view

[Sysname] lacp system-mac 1-1-1

Related commands

display link-aggregation verbose

port lacp system-mac

lacp system-number

Use lacp system-number to set the LACP system number used by the local device.

Use undo lacp system-number to restore the default.

Syntax

lacp system-number number

undo lacp system-number

Default

The LACP system number is not set.

Views

System view

Predefined user roles

network-admin

Parameters

number: Specifies a number in the range of 1 to 3.

Usage guidelines

You must assign a unique LACP system number to each S-MLAG device.

The LACP system number configured by using this command takes effect only on aggregate interfaces in S-MLAG groups. Aggregate interfaces not in S-MLAG groups do not use the configured LACP system number in LACPDUs. To view the LACP system number in LACPDUs, examine the Index field in the output from the display link-aggregation verbose command.

Examples

# Set the LACP system number to 1.

<Sysname> system-view

[Sysname] lacp system-number 1

Related commands

display link-aggregation verbose

lacp system-priority

Use lacp system-priority to set the LACP system priority.

Use undo lacp system-priority to restore the default.

Syntax

lacp system-priority priority

undo lacp system-priority

Default

The LACP system priority is 32768.

Views

System view

Predefined user roles

network-admin

Parameters

priority: Specifies the LACP system priority in the range of 0 to 65535. The smaller the value, the higher the LACP system priority.

Usage guidelines

LACPDUs carry the LACP system priority configured by using this command. To identify the LACP system priority used by a link aggregation group, examine the System ID field in the output from the display link-aggregation verbose command.

You can configure the LACP system priority globally and in aggregate interface view. The global LACP system priority takes effect on all aggregation groups, and an aggregate-interface-specific LACP system priority takes precedence over the global LACP system priority.

Examples

# Set the LACP system priority to 64.

<Sysname> system-view

[Sysname] lacp system-priority 64

Related commands

link-aggregation port-priority

port lacp system-priority

lacp transparent enable

Use lacp transparent enable to enable transparent LACPDU transmission on an interface.

Use undo lacp transparent enable to disable transparent LACPDU transmission on an interface.

Syntax

lacp transparent enable

undo lacp transparent enable

Default

Transparent LACPDU transmission is disabled on an interface.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

To establish a dynamic aggregation between two remote CEs in an L2VPN network, use transparent LACPDU transmission on the PEs to which the CEs are attached.

On the PEs, enable transparent LACPDU transmission on the interfaces that transmit traffic between CEs and PEs and between PEs.

Do not use an interface for dynamic link aggregation if you enable transparent LACPDU transmission on that interface. With transparent LACPDU transmission enabled, an interface cannot be selected for aggregation.

Examples

# Enable transparent LACPDU transmission on Ten-GigabitEthernet 1/0/1.

<Sysname> system

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] lacp transparent enable

link-aggregation auto-aggregation enable

Use link-aggregation auto-aggregation enable to enable automatic link aggregation.

Use undo link-aggregation auto-aggregation enable to disable automatic link aggregation.

Syntax

link-aggregation auto-aggregation enable

undo link-aggregation auto-aggregation enable

Default

Automatic link aggregation is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

After you enable automatic link aggregation and LLDP on two connected devices, they automatically establish a dynamic link aggregation based on the information in incoming LLDP frames. The devices each automatically create a dynamic aggregate interface and assign the redundant ports connected to the peer to the aggregation group of that interface. If you disable LLDP or automatic link aggregation on one device, that device removes the aggregation member ports from the aggregation group, but it will retain the aggregate interface. This event will not trigger member port removal actions on the peer device.

If automatic link aggregation is enabled, subinterface creation might fail on LLDP-enabled Layer 3 Ethernet interfaces. As a best practice, do not create subinterfaces on LLDP-enabled Layer 3 Ethernet interfaces.

To ensure correct operation of an automatically created aggregate interface, do not modify the configuration on the member ports of its aggregation group. Doing so might cause the member ports to be removed from the aggregation group.

For DRNI to operate correctly, do not use this command on a DR system.

On an interface, the port link-aggregation group setting takes precedence over automatic link aggregation. The interface will not be added to the aggregation group of an automatically created aggregate interface if it has been the member port of a manually created aggregate interface.

Examples

# Enable automatic link aggregation.

<Sysname> system

[Sysname] link-aggregation auto-aggregation enable

Related commands

lldp enable

lldp global enable

port link-aggregation group

link-aggregation bfd ipv4

Use link-aggregation bfd ipv4 to enable BFD for an aggregation group.

Use undo link-aggregation bfd to disable BFD for an aggregation group.

Syntax

link-aggregation bfd ipv4 source ip-address destination ip-address

undo link-aggregation bfd

Default

BFD is disabled for an aggregation group.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

source ip-address: Specifies the unicast source IP address of BFD sessions. The source IP address cannot be 0.0.0.0.

destination ip-address: Specifies the unicast destination IP address of BFD sessions. The destination IP address cannot be 0.0.0.0.

Usage guidelines

Make sure the source and destination IP addresses are reversed between the two ends of an aggregate link. For example, if you execute link-aggregation bfd ipv4 source 1.1.1.1 destination 2.2.2.2 at the local end, execute link-aggregation bfd ipv4 source 2.2.2.2 destination 1.1.1.1 at the peer end. The source and destination IP addresses cannot be the same.

The BFD parameters configured on an aggregate interface take effect on all BFD sessions established by the member ports in its aggregation group. BFD on a link aggregation supports only control packet mode for session establishment and maintenance. The two ends of an established BFD session can only operate in Asynchronous mode. For more information about BFD, see High Availability Configuration Guide.

As a best practice, do not configure BFD for any protocols on a BFD-enabled aggregate interface.

Make sure the number of member ports in the BFD-enabled aggregation group is less than or identical to the number of BFD sessions supported by the device. If the aggregation group contains more member ports than the supported sessions, some Selected ports might change to the Unselected state.

If the number of BFD sessions differs between the two ends of an aggregate link, check their settings for inconsistency in the maximum number of Selected ports. You must make sure the two ends have the same setting for the maximum number of Selected ports.

As a best practice, configure the same source and destination IP addresses for BFD sessions on the DR interfaces in the same DR group.

Examples

# Enable BFD for Layer 2 aggregation group 1, and specify the source and destination IP addresses as 1.1.1.1 and 2.2.2.2 for BFD sessions.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation bfd ipv4 source 1.1.1.1 destination 2.2.2.2

link-aggregation capability

Use link-aggregation capability to configure the link aggregation capability for the device.

Use undo link-aggregation capability to restore the default.

Syntax

link-aggregation capability max-group max-group-number max-selected-port max-selected-port-number

undo link-aggregation capability

Default

A device can have a maximum of 128 aggregation groups and an aggregation group can have a maximum of 8 Selected ports.

Views

System view

Predefined user roles

network-admin

Parameters

max-group max-group-number: Specifies the maximum number of aggregation groups that the device supports. For the S6520X-HI series, S6520X-EI series, S6520X-SI series (except S6520X-26XC-UPWR-SI and S6520X-54XC-UPWR-SI), S5560X-HI series, MS4600 series, and S6520-26Q-SI, the value for the max-group-number argument can be 61, 125, or 128. For the S6520-SI series (except S6520-26Q-SI), S5000-EI series, S6520X-26XC-UPWR-SI,  and S6520X-54XC-UPWR-SI, the value for the max-group-number argument can be 13, 29, or 61.

max-selected-port max-selected-port-number: Specifies the maximum number of Selected ports per aggregation group. The value for the max-selected-port-number argument can be 8, 16, or 32.

Usage guidelines

After you execute this command, save the configuration and reboot the device for the configuration to take effect. Before rebooting the device, make sure you know the possible impact on the network.

This command fails if the number of existing aggregation groups exceeds the configured maximum number.

If you create aggregation groups after executing the link-aggregation capability command and the number of aggregation groups exceeds the configured number, some aggregation groups are deleted at the next reboot.

The maximum number of Selected ports allowed in an aggregation group is limited by one of the following values, whichever value is smaller:

·     Maximum number set by using the link-aggregation selected-port maximum command.

·     Maximum number of Selected ports allowed by the link aggregation capability.

For link aggregation to operate correctly, set the same link aggregation capability for both ends of an aggregate link.

If you execute this command multiple times, the most recent configuration takes effect at the next reboot.

Examples

# Configure the device to support a maximum of 125 aggregation groups and a maximum of 16 Selected ports per aggregation group.

<Sysname> system-view

[Sysname] link-aggregation capability max-group 125 max-selected-port 16

The configuration will take effect at the next reboot. Continue? [Y/N]:y

Please save the configuration, and reboot the device.

Related commands

display link-aggregation capability

link-aggregation global load-sharing mode

Use link-aggregation global load-sharing mode to set the global link-aggregation load sharing mode.

Use undo link-aggregation global load-sharing mode to restore the default.

Syntax

link-aggregation global load-sharing mode { destination-ip | destination-mac | destination-port | ingress-port | source-ip | source-mac | source-port } *

undo link-aggregation global load-sharing mode

Default

Packets are load shared based on the following information:

·     Source and destination IP addresses.

·     Source and destination MAC addresses.

·     Source and destination ports.

Views

System view

Predefined user roles

network-admin

Parameters

destination-ip: Distributes traffic based on destination IP addresses.

destination-mac: Distributes traffic based on destination MAC addresses.

destination-port: Distributes traffic based on destination ports.

ingress-port: Distributes traffic based on ingress ports.

source-ip: Distributes traffic based on source IP addresses.

source-mac: Distributes traffic based on source MAC addresses.

source-port: Distributes traffic based on source ports.

Usage guidelines

If you execute this command multiple times, the most recent configuration takes effect.

If an unsupported load sharing mode is set, the device displays an error message.

The following are global load sharing modes supported on the device:

·     Default mode (load sharing mode automatically determined based on the packet type).

·     Source IP.

·     Destination IP.

·     Source MAC.

·     Destination MAC.

·     Ingress port.

·     Source IP and destination IP.

·     Source IP and source port.

·     Destination IP and destination port.

·     Source IP, source port, destination IP, and destination port.

·     Any combinations of ingress port, source MAC, and destination MAC.

Examples

# Set the global load sharing mode to load share packets based on destination MAC addresses.

<Sysname> system-view

[Sysname] link-aggregation global load-sharing mode destination-mac

link-aggregation lacp isolate

Use link-aggregation lacp isolate to isolate aggregate interfaces on the device.

Use undo link-aggregation lacp isolate to remove aggregate interface isolation.

Syntax

link-aggregation lacp isolate

undo link-aggregation lacp isolate

Default

Aggregate interfaces are not isolated.

Views

System view

Predefined user roles

network-admin

Usage guidelines

Aggregate interface isolation is applicable to the aggregate interfaces that act as DR interfaces when the device acts a DR member device in a DR system. It gracefully changes all DR interfaces on the device to the Unselected state and switch traffic over to their counterpart DR interfaces on the other DR member device.

This feature takes effect only on dynamic aggregate interfaces. It cannot isolate static aggregate interfaces or IPPs.

As a best practice, make sure no DR interfaces are in DRNI MAD DOWN state before you isolate them. If one of the DR interfaces is in DRNI MAD DOWN state when you isolate them, that DR interface will persist in that state and cannot forward traffic after the isolation is removed.

Examples

# Isolate aggregate interfaces.

<Sysname> system-view

[Sysname] link-aggregation lacp isolate

link-aggregation lacp traffic-redirect-notification enable

Use link-aggregation lacp traffic-redirect-notification enable to enable link-aggregation traffic redirection.

Use undo link-aggregation lacp traffic-redirect-notification enable to disable link-aggregation traffic redirection.

Syntax

link-aggregation lacp traffic-redirect-notification enable

undo link-aggregation lacp traffic-redirect-notification enable

Default

Link-aggregation traffic redirection is disabled.

Views

System view

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

This feature redirects traffic on a Selected port to the remaining available Selected ports of an aggregation group if one of the following events occurs:

·     The port is shut down by using the shutdown command.

·     The slot that hosts the port reboots, and the aggregation group spans multiple slots.

 

 

NOTE:

The device does not redirect traffic to member ports that become Selected during the traffic redirection process.

 

This feature ensures zero packet loss for known unicast traffic, but it does not protect other types of traffic.

This feature applies only to dynamic link aggregation groups.

To prevent traffic interruption, enable link-aggregation traffic redirection on devices at both ends of the aggregate link.

To prevent packet loss that might occur when a slot reboots, do not enable spanning tree together with link-aggregation traffic redirection.

Link-aggregation traffic redirection cannot operate correctly on an edge aggregate interface.

Global link-aggregation traffic redirection settings take effect on all aggregation groups. A link aggregation group preferentially uses the group-specific link-aggregation traffic redirection settings. If group-specific link-aggregation traffic redirection is not configured, the group uses the global link-aggregation traffic redirection settings.

As a best practice, enable link-aggregation traffic redirection on a per-interface basis. If you enable this feature globally, communication with a third-party peer device might be affected if the peer is not compatible with this feature.

As a best practice, make sure the status of link-aggregation traffic redirection is the same on the DR interfaces in the same DR group.

Examples

# Enable link-aggregation traffic redirection.

<Sysname> system-view

[Sysname] link-aggregation lacp traffic-redirect-notification enable

link-aggregation load-sharing mode local-first

Use link-aggregation load-sharing mode local-first to enable local-first load sharing for link aggregation.

Use undo link-aggregation load-sharing mode local-first to disable local-first load sharing for link aggregation.

Syntax

link-aggregation load-sharing mode local-first

undo link-aggregation load-sharing mode local-first

Default

Local-first load sharing is enabled for link aggregation.

Views

System view

Predefined user roles

network-admin

Usage guidelines

Use local-first load sharing in a multidevice link aggregation scenario to distribute traffic preferentially across member ports on the ingress card or device. Local-first load sharing takes effect only on known unicast traffic.

If you disable local-first load sharing, packets on an aggregate interface are load shared among all its Selected ports on IRF member devices.

Examples

# Disable local-first load sharing for link aggregation.

<Sysname> system-view

[Sysname] undo link-aggregation load-sharing mode local-first

link-aggregation mode

Use link-aggregation mode dynamic to configure an aggregation group to operate in dynamic aggregation mode and enable LACP.

Use undo link-aggregation mode to restore the default.

Syntax

link-aggregation mode dynamic

undo link-aggregation mode

Default

An aggregation group operates in static aggregation mode.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

When you change the aggregation mode, make sure you understand the impact of the change on services.

Aggregation mode change might cause Selected member ports to become Unselected.

Examples

# Configure Layer 2 aggregation group 1 to operate in dynamic aggregation mode.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation mode dynamic

link-aggregation port-priority

Use link-aggregation port-priority to set the port priority of an interface.

Use undo link-aggregation port-priority to restore the default.

Syntax

link-aggregation port-priority priority

undo link-aggregation port-priority

Default

The port priority of an interface is 32768.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

priority: Specifies the port priority in the range of 0 to 65535. The smaller the value, the higher the port priority.

Examples

# Set the port priority to 64 for Layer 2 Ethernet interface Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] link-aggregation port-priority 64

# Set the port priority to 64 for Layer 3 Ethernet interface Ten-GigabitEthernet 1/0/2.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/2

[Sysname-Ten-GigabitEthernet1/0/2] link-aggregation port-priority 64

Related commands

lacp system-priority

link-aggregation selected-port maximum

Use link-aggregation selected-port maximum to set the maximum number of Selected ports allowed in an aggregation group.

Use undo link-aggregation selected-port maximum to restore the default.

Syntax

link-aggregation selected-port maximum max-number [ lacp-sync ]

undo link-aggregation selected-port maximum

Default

The maximum number of Selected ports allowed in an aggregation group is 8.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

max-number: Specifies the maximum number of Selected ports allowed in an aggregation group. The value range for this argument is 1 to 8.

lacp-sync: Synchronizes the maximum number of Selected ports through LACPDUs. If you do not specify this keyword, the aggregate interface does not synchronize the maximum number of Selected ports with the peer.

Usage guidelines

Executing this command might cause some of the Selected ports in an aggregation group to become Unselected ports.

For a static aggregate link, you must set the maximum number of Selected ports to the same value at its two ends.

For a dynamic aggregate link, you must set the maximum number of Selected ports to the same value at its two ends if you do not specify the lacp-sync keyword. If you specify this keyword, the two ends of the aggregate link compare their maximum Selected port number settings and use the smaller value.

The maximum number of Selected ports allowed in the aggregation groups must be the same for the local and peer ends.

For an aggregation group, the maximum number of Selected ports must be equal to or higher than the minimum number of Selected ports.

The maximum number of Selected ports allowed in an aggregation group is limited by one of the following values, whichever value is smaller:

·     Maximum number set by using the link-aggregation selected-port maximum command.

·     Maximum number of Selected ports allowed by the link aggregation capability.

You can implement backup between two ports by performing the following tasks:

·     Assigning two ports to an aggregation group.

·     Setting the maximum number of Selected ports to 1 for the aggregation group.

Then, only one Selected port is allowed in the aggregation group at any point in time, while the Unselected port acts as a backup port.

Examples

# Set the maximum number of Selected ports to 5 for Layer 2 aggregation group 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation selected-port maximum 5

Related commands

link-aggregation selected-port minimum

link-aggregation selected-port minimum

Use link-aggregation selected-port minimum to set the minimum number of Selected ports in an aggregation group.

Use undo link-aggregation selected-port minimum to restore the default.

Syntax

link-aggregation selected-port minimum { min-number | percentage number }

undo link-aggregation selected-port minimum

Default

The minimum number of Selected ports in an aggregation group is not specified.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

min-number: Specifies the minimum number of Selected ports in an aggregation group required to bring up the aggregate interface. The value range for this argument is 1 to 8.

percentage number: Sets the minimum percentage of Selected ports in an aggregation group. The value range for the number argument is 1 to 100.

Usage guidelines

IMPORTANT

IMPORTANT:

After you set the minimum percentage of Selected ports for an aggregation group, aggregate interface flapping might occur when ports join or leave an aggregation group. Make sure you are fully aware of the impacts of this setting when you configure it on a live network.

 

You can set either the minimum number or the minimum percentage of Selected ports for an aggregation group. If you configure both settings on an aggregate interface, the higher Selected port number limit takes effect.

Executing this command might cause all member ports in the aggregation group to become Unselected ports.

You must set the same minimum number or minimum percentage of Selected ports at the two ends of an aggregate link.

For an aggregation group, the minimum number of Selected ports must be equal to or lower than the maximum number of Selected ports.

Examples

# Set the minimum number of Selected ports to 3 for Layer 2 aggregation group 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation selected-port minimum 3

Related commands

link-aggregation selected-port maximum

link-delay

Use link-delay to set the physical state change suppression interval on an aggregate interface.

Use undo link-delay to restore the default.

Syntax

link-delay { down | up } [ msec ] delay-time

undo link-delay { down | up }

Default

Each time the physical link of an aggregate interface goes up or comes down, the system immediately reports the change to the CPU.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

down: Suppresses link-down events.

up: Suppresses link-up events.

msec: Sets the physical state change suppression interval in milliseconds. If you do not specify this keyword, the suppression interval is in seconds.

delay-time: Sets the physical state change suppression interval. To report a physical state change immediately to the CPU, set the interval to 0.

·     If you do not specify the msec keyword, the value range is 0 to 30 seconds.

·     If you specify the msec keyword, the value range is 0 to 10000 milliseconds, and the value must be a multiple of 100.

Usage guidelines

You can configure this feature to suppress link-down events, link-up events, or both. If an event of the specified type persists when the suppression interval expires, the system reports the event.

On an interface, you can configure different suppression intervals for link-up and link-down events. If you execute the link-delay command multiple times for an event type, the most recent configuration takes effect on that event type.

When you configure suppression interval settings on an aggregate interface, make sure its peer interface is also an aggregate interface in the same aggregation mode. In addition, the suppression interval settings must be the same between the peer aggregate interfaces.

As a best practice, use the default setting in an S-MLAG environment.

Use this command on an aggregate interface to reduce the impact of interface flapping on upper-layer services, for example, on a DRNI IPP. For more information about IPPs, see Layer 2—LAN Switching Configuration Guide.

Examples

# Set the link-down event suppression interval to 8 seconds on Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-delay down 8

# Set the link-down event suppression interval to 8 seconds on Route-Aggregation 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] link-delay down 8

mtu

Use mtu to set the MTU of a Layer 3 aggregate interface or subinterface.

Use undo mtu to restore the default.

Syntax

mtu size

undo mtu

Default

The MTU of Layer 3 aggregate interfaces and subinterfaces is 1500 bytes.

Views

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

Predefined user roles

network-admin

Parameters

size: Specifies an MTU in bytes. The value range for this argument is 128 to 1560.

Examples

# Set the MTU of interface Route-Aggregation 1 to 1430 bytes.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] mtu 1430

Related commands

display interface

port lacp system-mac

Use port lacp system-mac to set the LACP system MAC address on an aggregate interface.

Use undo port lacp system to restore the default.

Syntax

port lacp system-mac mac-address

undo port lacp system-mac

Default

The LACP system MAC address is the bridge MAC address of the device.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

mac-address: Specifies a MAC address in the format of H-H-H. The MAC address cannot be an all-zero, all-F, or multicast MAC address.

Usage guidelines

LACPDUs carry the LACP system MAC address configured by using this command. To identify the LACP system MAC address used by a link aggregation group, examine the System ID field in the output from the display link-aggregation verbose command.

You can configure the LACP system MAC address globally and in aggregate interface view. The global LACP system MAC address takes effect on all aggregation groups, and an aggregate-interface-specific LACP system MAC address takes precedence over the global LACP system MAC address.

Member devices in an S-MLAG system must use the same LACP system MAC address.

On a DR system, DR interfaces in the same DR group must use the same LACP system MAC address.

Examples

# Set the LACP system MAC address to 0002-0002-0002 on Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] port lacp system-mac 2-2-2

Related commands

display link-aggregation verbose

lacp system-mac

port lacp system-priority

Use port lacp system-priority to set the LACP system priority on an aggregate interface.

Use undo port lacp system-priority to restore the default.

Syntax

port lacp system-priority priority

undo port lacp system-priority

Default

The LACP system priority is 32768.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

priority: Specifies the LACP system priority in the range of 0 to 65535. The smaller the value, the higher the LACP system priority.

Usage guidelines

LACPDUs carry the LACP system priority configured by using this command. To identify the LACP system priority used by a link aggregation group, examine the System ID field in the output from the display link-aggregation verbose command.

You can configure the LACP system priority globally and in aggregate interface view. The global LACP system priority takes effect on all aggregation groups, and an aggregate-interface-specific LACP system priority takes precedence over the global LACP system priority.

Member devices in an S-MLAG system must use the same LACP system priority.

Examples

# Set the LACP system priority to 32 on Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] port lacp system-priority 32

Related commands

display link-aggregation verbose

lacp system-priority

port link-aggregation group

Use port link-aggregation group to assign an interface to an aggregation group.

Use undo port link-aggregation group to remove an interface from the aggregation group to which it belongs.

Syntax

port link-aggregation group { group-id [ force ] | auto [ group-id ] }

undo port link-aggregation group

Default

An interface does not belong to any aggregation group.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

group-id: Specifies an aggregation group by its aggregate interface number. The value range for the number argument is 1 to 1024.

force: Enables the current interface to synchronize attribute configurations from the aggregate interface. If you do not specify this keyword, the current interface does not synchronize attribute configurations from the aggregate interface when it joins the aggregation group. This keyword is supported only on Layer 2 Ethernet interfaces.

auto: Enables automatic assignment.

Usage guidelines

A Layer 2 Ethernet interface can be assigned to a Layer 2 aggregation group only. A Layer 3 Ethernet interface can be assigned to a Layer 3 aggregation group only.

An interface can belong to only one aggregation group.

An interface cannot join an aggregation group if it has different attribute configurations from the aggregate interface. After joining an aggregation group, an interface inherits the attribute configurations on the aggregate interface. You can modify the attribute configurations only on the aggregate interface.

The force keyword takes effect only when you assign the interface to an aggregation group. It cannot be saved in the running configuration or a configuration file.

Automatic assignment is available only on Layer 2 and Layer 3 Ethernet interfaces.

When you enable automatic assignment, you can specify a preferred aggregation group, which must be in dynamic mode.

The device assigns the interface to the preferred aggregation group as long as the LACPDUs received on the interface match the peer information of the reference port in the group.

If you do not specify a preferred group or if the preferred group match fails, the device attempts to select a matching group from the existing dynamic aggregation groups. If no match is found, the device creates a dynamic aggregation group based on the LACPDUs and assigns the interface to that aggregation group.

As a best practice, do not modify the configuration on an automatically created aggregate interface or its member ports.

Examples

# Assign Layer 2 Ethernet interface Ten-GigabitEthernet 1/0/1 to Layer 2 aggregation group 1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] port link-aggregation group 1

# Assign Layer 3 Ethernet interface Ten-GigabitEthernet 1/0/2 to Layer 3 aggregation group 2.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/2

[Sysname-Ten-GigabitEthernet1/0/2] port link-aggregation group 2

port s-mlag group

Use port s-mlag group to assign an aggregate interface to an S-MLAG group.

Use undo port s-mlag group to restore the default.

Syntax

port s-mlag group group-id

undo port s-mlag group

Default

An aggregate interface is not in any S-MLAG group.

Views

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

group-id: Specifies an S-MLAG group number in the range of 1 to 1024.

Usage guidelines

Use S-MLAG only to establish aggregate links with servers.

You can assign only Layer 2 aggregate interfaces in dynamic mode to an S-MLAG group.

Each S-MLAG group can contain only one aggregate interface on each device.

The aggregate interfaces in an S-MLAG group cannot be used as DR interfaces or IPPs in DRNI. For more information about DR interfaces and IPPs, see DRNI configuration in Layer 2—LAN Switching Configuration Guide.

Examples

# Assign Bridge-Aggregation 1 to S-MLAG group 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] port s-mlag group 1

reset counters interface

Use reset counters interface to clear statistics for the specified aggregate interfaces.

Syntax

reset counters interface [ { bridge-aggregation | route-aggregation } [ interface-number ] ]

Views

User view

Predefined user roles

network-admin

Parameters

bridge-aggregation: Specifies Layer 2 aggregate interfaces.

route-aggregation: Specifies Layer 3 aggregate interfaces.

interface-number: Specifies an existing aggregate interface number.

Usage guidelines

Use this command to clear history statistics before you collect traffic statistics for a time period.

If you do not specify an aggregate interface type, the command clears statistics for all interfaces in the system.

If you specify only an aggregate interface type, the command clears statistics for all aggregate interfaces of the specified type.

The bridge-aggregation or route-aggregation keyword is available only when aggregate interfaces of the corresponding type exist on the device.

Examples

# Clear the statistics about interface Bridge-Aggregation 1.

<Sysname> reset counters interface bridge-aggregation 1

reset lacp statistics

Use reset lacp statistics to clear LACP statistics for the specified link aggregation member ports.

Syntax

reset lacp statistics [ interface interface-list ]

Views

User view

Predefined user roles

network-admin

Parameters

interface interface-list: Specifies a list of link aggregation member ports, in the format interface-type interface-number1 [ to interface-type interface-number2 ]. The value for the interface-number1 argument must be equal to or greater than the value for the interface-number2 argument. If you do not specify any member ports, the command clears LACP statistics for all member ports.

Examples

# Clear LACP statistics for all link aggregation member ports.

<Sysname> reset lacp statistics

Related commands

display link-aggregation member-port

shutdown

Use shutdown to shut down an interface.

Use undo shutdown to bring up an interface.

Syntax

shutdown

undo shutdown

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

Predefined user roles

network-admin

Usage guidelines

CAUTION

CAUTION:

The shutdown command will disconnect all links established on an interface. Make sure you are fully aware of the impacts of this command when you use it on a live network.

 

Shutting down or bringing up a Layer 3 aggregate interface shuts down or brings up its subinterfaces. Shutting down or bringing up a Layer 3 aggregate subinterface does not affect its main interface.

Examples

# Bring up Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] undo shutdown

 

  • Cloud & AI
  • InterConnect
  • Intelligent Computing
  • Security
  • SMB Products
  • Intelligent Terminal Products
  • Product Support Services
  • Technical Service Solutions
All Services
  • Resource Center
  • Policy
  • Online Help
All Support
  • Become a Partner
  • Partner Resources
  • Partner Business Management
All Partners
  • Profile
  • News & Events
  • Online Exhibition Center
  • Contact Us
All About Us
新华三官网