Login
- Table of Contents
- Related Documents
-
| Title | Size | Download |
|---|---|---|
| 05-Loop detection commands | 73.77 KB |
Contents
loopback-detection global action
loopback-detection global enable
loopback-detection interval-time
display loopback-detection
Use display loopback-detection to display the loop detection configuration and status.
Syntax
display loopback-detection
Views
Any view
Predefined user roles
network-admin
network-operator
mdc-admin
mdc-operator
Example
# Display the loop detection configuration and status.
<Sysname> display loopback-detection
Loopback detection is enabled.
Loopback detection interval is 30 second(s).
Loopback is detected on following interfaces:
Interface Action mode
GigabitEthernet3/0/2 Shutdown
GigabitEthernet3/0/3 None
Table 1 Command output
|
Field |
Description |
|
Action mode |
Loop protection action: · None—When a loop is detected on a port, the device generates a log but performs no action on the port. · Shutdown—When a loop is detected on a port, the device generates a log and shuts down the port to disable it from receiving and sending any frames. |
loopback-detection action
Use loopback-detection action to configure the loop protection action on a per-port basis.
Use undo loopback-detection action to restore the default.
Syntax
loopback-detection action shutdown
undo loopback-detection action
Default
When the device detects a loop on a port, it generates a log but performs no action on the port.
Views
Layer 2 Ethernet interface view, Layer 2 aggregate interface view
Predefined user roles
network-admin
mdc-admin
Parameters
shutdown: Enables the shutdown mode. If a loop is detected, the device generates a log and shuts down the port.
Usage guidelines
To configure the loop protection action globally, use the loopback-detection global action command.
The global configuration applies to all ports. The per-port configuration applies to the individual ports. The per-port configuration takes precedence over the global configuration.
Example
# Set the loop protection action to shutdown on port GigabitEthernet 3/0/1.
<Sysname> system-view
[Sysname] interface gigabitethernet 3/0/1
[System-GigabitEthernet3/0/1] loopback-detection action shutdown
· display loopback-detection
· loopback-detection global action
loopback-detection enable
Use loopback-detection enable to enable loop detection on a per-port basis.
Use undo loopback-detection enable to disable loop detection on a port.
Syntax
loopback-detection enable vlan { vlan-list | all }
undo loopback-detection enable vlan { vlan-list | all }
Default
The loop detection feature is disabled on ports.
Views
Layer 2 Ethernet interface view, Layer 2 aggregate interface view
Predefined user roles
network-admin
mdc-admin
Parameters
vlan-list: Specifies a space-separated list of up to 10 VLAN items. Each item specifies a VLAN ID or a range of VLAN IDs in the form of vlan-id1 to vlan-id2. The value range for VLAN IDs is 1 to 4094. The ID for vlan-id2 must be equal to or greater than the ID for vlan-id1.
all: Specifies all existing VLANs.
Usage guidelines
To enable loop detection globally, use the loopback-detection global enable command.
The global configuration applies to all ports in the specified VLAN. The per-port configuration applies to the individual port only when the port belongs to the specified VLAN. The per-port configuration takes precedence over the global configuration.
Example
# Enable loop detection on port GigabitEthernet 3/0/1 for VLAN 10 through VLAN 20.
<Sysname> system-view
[Sysname] interface gigabitethernet 3/0/1
[System-GigabitEthernet3/0/1] loopback-detection enable vlan 10 to 20
· display loopback-detection
· loopback-detection global enable
loopback-detection global action
Use loopback-detection global action to configure the global loop protection action.
Use undo loopback-detection global action to restore the default.
Syntax
loopback-detection global action shutdown
undo loopback-detection global action
Default
When the device detects a loop on a port, it generates a log but performs no action on the port.
Views
System view
Predefined user roles
network-admin
mdc-admin
Parameters
shutdown: Enables the shutdown mode. If a loop is detected, the device generates a log and shuts down the port.
Usage guidelines
To configure the loop protection action on a per-port basis, use the loopback-detection action command in interface view.
The global configuration applies to all ports. The per-port configuration applies to the individual ports. The per-port configuration takes precedence over the global configuration.
Example
# Set the global loop protection action to shutdown.
<Sysname> system-view
[System] loopback-detection global action shutdown
Related commands
· display loopback-detection
· loopback-detection action
loopback-detection global enable
Use loopback-detection global enable to enable loop detection globally.
Use undo loopback-detection global enable to disable loop detection globally.
Syntax
loopback-detection global enable vlan { vlan-list | all }
undo loopback-detection global enable vlan { vlan-list | all }
Default
The loop detection feature is globally disabled.
Views
System view
Predefined user roles
network-admin
mdc-admin
Parameters
vlan-list: Specifies a space-separated list of up to 10 VLAN items. Each item specifies a VLAN ID or a range of VLAN IDs in the form of vlan-id1 to vlan-id2. The value range for VLAN IDs is 1 to 4094. The ID for vlan-id2 must be equal to or greater than the ID for vlan-id1.
all: Specifies all existing VLANs.
Usage guidelines
To enable loop detection on a per-port basis, use the loopback-detection enable command in interface view.
The global configuration applies to all ports in the specified VLAN. The per-port configuration applies to the individual port only when the port belongs to the specified VLAN. The per-port configuration takes precedence over the global configuration.
Example
# Globally enable loop detection for VLAN 10 through VLAN 20.
<Sysname> system-view
[System] loopback-detection global enable vlan 10 to 20
Related commands
· display loopback-detection
· loopback-detection enable
loopback-detection interval-time
Use loopback-detection interval-time to set the loop detection interval.
Use undo loopback-detection interval-time to restore the default.
Syntax
loopback-detection interval-time interval
undo loopback-detection interval-time
Default
The loop detection interval is 30 seconds.
Views
System view
Predefined user roles
network-admin
mdc-admin
Parameters
interval: Sets the loop detection interval (in seconds) in the range of 1 to 300.
Usage guidelines
With loop detection enabled, the device sends loop detection frames at the specified interval. A shorter interval offers more sensitive detection but consumes more resources. Consider the system performance and loop detection speed when you set the loop detection interval.
Example
# Set the loop detection interval to 10 seconds.
<Sysname> system-view
[Sysname] loopback-detection interval-time 10
Related commands
display loopback-detection
