- Table of Contents
-
- H3C S3100 Series Ethernet Switches Command Manual (For Soliton)(V1.02)
- 00-1Cover
- 01-CLI Commands
- 02-Login Commands
- 03-Configuration File Management Commands
- 04-VLAN Commands
- 05-Management VLAN Commands
- 06-IP Address-IP Performance Commands
- 07-Voice VLAN Commands
- 08-GVRP Commands
- 09-Port Basic Configuration Commands
- 10-Link Aggregation Commands
- 11-Port Isolation Commands
- 12-Port Security-Port Binding Commands
- 13-DLDP Commands
- 14-MAC Address Table Management Commands
- 15-MSTP Commands
- 16-Multicast Commands
- 17-802.1x-System Guard Commands
- 18-AAA Commands
- 19-MAC Address Authentication Commands
- 20-ARP Commands
- 21-DHCP Commands
- 22-ACL Commands
- 23-QoS-QoS Profile Commands
- 24-Mirroring Commands
- 25-Stack-Cluster Commands
- 26-SNMP-RMON Commands
- 27-NTP Commands
- 28-SSH Commands
- 29-File System Management Commands
- 30-FTP-SFTP-TFTP Commands
- 31-Information Center Commands
- 32-System Maintenance and Debugging Commands
- 33-VLAN-VPN Commands
- 34-HWPing Commands
- 35-IPv6 Management Commands
- 36-DNS Commands
- 37-Smart Link-Monitor Link Commands
- 38-Appendix
- Related Documents
-
Title | Size | Download |
---|---|---|
05-Management VLAN Commands | 84.62 KB |
Chapter 1 Management VLAN Configuration Commands
1.1 Management VLAN Configuration Commands
1.1.1 delete static-routes all
1.1.2 display interface Vlan-interface
1.1.4 display ip interface brief
1.1.5 display ip routing-table
1.1.6 display ip routing-table acl
1.1.7 display ip routing-table ip-address
1.1.8 display ip routing-table ip-address1 ip-address2
1.1.9 display ip routing-table protocol
1.1.10 display ip routing-table radix.
1.1.11 display ip routing-table statistics
1.1.12 display ip routing-table verbose
1.1.13 interface Vlan-interface
1.1.17 reset ip routing-table statistics protocol
Chapter 1 Management VLAN Configuration Commands
1.1 Management VLAN Configuration Commands
1.1.1 delete static-routes all
Syntax
delete static-routes all
View
System view
Parameter
None
Description
Use the delete static-routes all command to delete all static routes.
The system will request your confirmation before it deletes all the configured static routes.
Related command: ip route-static and display ip routing-table.
Example
# Delete all the static routes in the router.
<Sysname> system-view
System View: return to User View with Ctrl+Z.
[Sysname] delete static-routes all
Are you sure to delete all the unicast static routes?[Y/N]y
1.1.2 display interface Vlan-interface
Syntax
display interface Vlan-interface [ vlan-id ]
View
Any view
Parameter
vlan-id: ID of the management VLAN interface the information about which is to be displayed.
Description
Use the display interface Vlan-interface command to display the information about the management VLAN interface.
Related command: interface Vlan-interface.
Example
<Sysname> display interface Vlan-interface 1
Vlan-interface1 current state : DOWN
Line protocol current state : DOWN
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 000f-e256-ae10
Internet Address is 192.168.0.39/24 Primary
Description : Vlan-interface1 Interface
The Maximum Transmit Unit is 1500
Table 1-1 Description on the fields of the display interface Vlan-interface command
Field |
Description |
Vlan-interface current state |
Current state of Vlan-interface1 |
Line protocol current state |
Current state of the link layer protocol |
IP Sending Frames' Format |
Format of the sent IP packets |
Hardware address |
MAC address corresponding to the management VLAN interface |
Internet Address Primary |
Primary IP address |
Description |
Description string assigned to the VLAN interface |
The Maximum Transmit Unit |
The maximum transmit unit (MTU) |
1.1.3 display ip interface
Syntax
display ip interface [ Vlan-interface vlan-id ]
View
Any view
Parameter
vlan-id: ID of the management VLAN interface.
Description
Use the display ip interface command to display the information about a specified VLAN interface.
Example
# Display the information about VLAN-interface 1.
<Sysname> display ip interface Vlan-interface 1
Vlan-interface1 current state :UP
Line protocol current state :UP
Internet Address is 192.168.0.39/24 Primary
Broadcast address : 192.168.0.255
The Maximum Transmit Unit : 1500 bytes
IP packets input number: 7420, bytes: 557679, multicasts: 1
IP packets output number: 7509, bytes: 385809, multicasts: 0
TTL invalid packet number: 0
ICMP packet input number: 0
Echo reply: 0
Unreachable: 0
Source quench: 0
Routing redirect: 0
Echo request: 0
Router advert: 0
Router solicit: 0
Time exceed: 0
IP header bad: 0
Timestamp request: 0
Timestamp reply: 0
Information request: 0
Information reply: 0
Netmask request: 0
Netmask reply: 0
Unknown type: 0
Table 1-2 Description on the fields of the display ip interface command
Field |
Description |
Vlan-interface1 current state |
Current state of Vlan-interface1 |
Line protocol current state |
Current state of the link layer protocol |
Internet Address |
IP address |
Broadcast address |
Broadcast address |
The Maximum Transmit Unit |
The maximum transmit unit (MTU) |
IP packets input number: 11790, bytes: 550920, multicasts: 3049 IP packets output number: 8374, bytes: 404537, multicasts: 0 |
Number of received/sent packets (total), bytes, and multicast packets. |
TTL invalid packet number |
Number of received packets with TTL errors |
ICMP packet input number |
Number of received ICMP messages |
Echo reply |
Echo replies |
Unreachable |
Unreachable messages |
Source quench |
Source quench messages |
Routing redirect |
Routing redirect messages |
Echo request |
Echo requests |
Router advert |
Router advertisements |
Router solicit |
Router solicit messages |
Time exceed |
Time exceed messages |
IP header bad |
IP header bad messages |
Timestamp request |
Timestamp requests |
Timestamp reply |
Timestamp replies |
Information request |
Information requests |
Information reply |
Information replies |
Netmask request |
Netmask requests |
Netmask reply |
Netmask replies |
Unknown type |
Messages with unknown type |
1.1.4 display ip interface brief
Syntax
display ip interface brief [ Vlan-interface [ vlan-id ] ]
View
Any view
Parameter
vlan-id: ID of the management VLAN interface.
Description
Use the display ip interface brief command to display brief information about a specified VLAN interface.
Example
# Display brief information about VLAN-interface1.
<Sysname> display ip interface brief vlan-interface 1
*down: administratively down
(l): loopback
(s): spoofing
Interface IP Address Physical Protocol Description
Vlan-interface1 192.168.0.39 up up Vlan-inte...
Table 1-3 Description on fields of the display ip interface brief command
Field |
Description |
*down |
The interface is administratively shut down with the shutdown command. |
(s) |
Spoofing attribute of the interface. It indicates that the interface whose link layer protocol is displayed up may have no such a link present or the link is set up only on demand. |
Interface |
Interface name |
IP Address |
IP address of the interface (If no IP address is configured, “unassigned” is displayed.) |
Physical |
Physical state of the interface |
Protocol |
Link layer protocol state of the interface |
Description |
Description information for the interface |
1.1.5 display ip routing-table
Syntax
display ip routing-table [ | { begin | exclude | include } regular-expression ]
View
Any view
Parameter
regular-expression: Regular expression, which specifies a match character string.
|: Uses the regular expression to match the output routing information.
begin: Displays the routing information from the route entry containing the specified character string.
include: Displays all routing information containing the specified character string.
exclude: Displays all routing information without the specified character string.
Description
Use the display ip routing-table command to display the summary information about the routing table.
This command displays the summary information about a routing table, with the items of a routing entry contained in one line. The information displayed includes destination IP address/mask length, protocol, preference, cost, next hop and outbound interface.
The display ip routing-table command only displays the routes currently in use, that is, the optimal routes.
Example
# Display the summary information about the routing table.
<Sysname> display ip routing-table
Routing Table: public net
Destination/Mask Protocol Pre Cost Nexthop Interface
127.0.0.0/8 DIRECT 0 0 127.0.0.1 InLoopBack0
127.0.0.1/32 DIRECT 0 0 127.0.0.1 InLoopBack0
Table 1-4 Description on the fields of the display ip routing-table command
Field |
Description |
Destination/Mask |
Destination IP address/mask length |
Protocol |
Routing protocol that discovers the route |
Pre |
Route preference |
Cost |
Route cost |
Nexthop |
Next hop IP address of the route |
Interface |
Outbound interface, through which packets destined for the destination network segment are to be transmitted |
1.1.6 display ip routing-table acl
Syntax
display ip routing-table acl acl-number [ verbose ]
View
Any view
Parameter
acl-number: Number of a basic access control list (ACL), in the range of 2000 to 2999.
verbose: Displays the detailed information about the active and inactive routes that match the specified ACL. If you do not specify this keyword, only the summary information about the active routes matching the specified ACL is displayed.
Description
Use the display ip routing-table acl command to display the routes that match a specified basic ACL.
As this command displays the routes that match a specified basic ACL, you can use it to trace routing policies.
Example
# Display the summary information about the active routes that match ACL 2000.
<Sysname> system-view
System View: return to User View with Ctrl+Z.
[Sysname] acl number 2000
[Sysname-acl-basic-2000] rule permit source 10.1.1.1 0.0.0.255
[Sysname-acl-basic-2000] rule deny source any
[Sysname-acl-basic-2000] display ip routing-table acl 2000
Routes matched by access-list 2000:
Summary count: 1
Destination/Mask Protocol Pre Cost Nexthop Interface
10.1.1.0/24 STATIC 60 0 192.168.0.31 Vlan-interface1
Refer to Table 1-4 for the description on the output fields.
# Display the detailed information about the active and inactive routes that match ACL 2000.
[Sysname] display ip routing-table acl 2000 verbose
Routes matched by access-list 2000:
+ = Active Route, - = Last Active, # = Both * = Next hop in use
Summary count: 1
**Destination: 10.1.1.0 Mask: 255.255.255.0
Protocol: #STATIC Preference: 60
*NextHop: 192.168.0.31 Interface: 192.168.0.51(Vlan-interface1)
State: <Int ActiveU Gateway Static Unicast>
Age: 1:48:18 Cost: 0/0
Table 1-5 Description on the fields of the display ip routing-table acl command
Field |
Description |
|
Destination |
Destination address |
|
Mask |
Mask |
|
Protocol |
Routing protocol that discovers the route |
|
Preference |
Route preference |
|
NextHop |
Next hop IP address |
|
Interface |
Outbound interface, through which packets destined for the destination network segment are to be transmitted |
|
State |
Descriptions on the route state are as follows: |
|
ActiveU |
Valid unicast route. “U” stands for unicast. |
|
Blackhole |
Blackhole route is the same as reject route except that a router drops a packet traveling along a blackhole route without sending ICMP unreachable messages to the source of the packets. |
|
Delete |
The route is deleted. |
|
Gateway |
The route is not a direct route. |
|
Hidden |
The route is a hidden route. The system hides routes that are temporarily unavailable for some reasons (such as the policy configured or the interface is down) for later use. |
|
Holddown |
The route is held down. Holddown is a kind of route advertisement policy used in some D-V (distance vector) routing protocols (such as RIP) to avoid the propagation of some incorrect routes and improve the transmission speed of route-unreachable information. For details, refer to corresponding routing protocols. |
|
Int |
The route is discovered by the internal gateway protocol (IGP). |
|
NoAdvise |
The route is not advertised when the router advertises routes based on policies |
|
NotInstall |
The route are not loaded to the core routing table but can be advertised. Normally, the routes with the highest preference in the routing table are loaded to the core routing table and are advertised. |
|
Reject |
The packets travel along the route will be dropped. Besides, the router sends ICMP unreachable messages to the source of the dropped packets. The Reject routes are usually used for network testing. |
|
Retain |
The route is not deleted when the routes in the core routing table are deleted. You can enable static routes to remain in the core routing table by configure them to be in retain state. |
|
Static |
Static routes configured manually on the router are marked as static. Such routes are not lost when you perform the save operation and then restart the router. |
|
Unicast |
The route is a unicast route. |
|
Age |
Time period during which the route is allowed to be in the routing table, in the form of hh:mm:ss. |
|
Cost |
Cost of the route |
1.1.7 display ip routing-table ip-address
Syntax
display ip routing-table ip-address [ mask ] [ longer-match ] [ verbose ]
View
Any view
Parameter
ip-address: Destination IP address, in dotted decimal notation.
mask: Mask of the destination IP address, which can be in dotted decimal notation or be an integer ranging from 0 to 32.
longer-match: Displays all the routes leading to the destination coupled with the default mask.
verbose: Displays the detailed information about the active and inactive routes leading to the destination. If this keyword is not specified, only the summary information about the active routes is displayed.
Description
Use the display ip routing-table ip-address command to display the information about the routes leading to a specified destination.
The output information of this command differs with the arguments/keywords specified as follows:
l display ip routing-table ip-address
For the destination address ip-address, if there are some routes matched within the natural mask range, the active routes which best match ip-address are displayed.
l display ip routing-table ip-address mask
Only the routes which match exactly the specified destination address and mask are displayed.
l display ip routing-table ip-address longer-match
All routes with their destination addresses matched within the natural mask range are displayed.
l display ip routing-table ip-address mask longer-match
All routes with their destination addresses matched within the specified mask range are displayed.
Example
# Display the summary information of the routes with their destination addresses matched within the natural mask range.
<Sysname> display ip routing-table 10.1.1.0
Destination/Mask Protocol Pre Cost Nexthop Interface
10.1.1.0/24 STATIC 60 0 192.168.0.31 Vlan-interface1
Refer to Table 1-4 for the description on the output fields.
# Display the detailed information of the routes with their destination addresses matched within the natural mask range.
<Sysname> display ip routing-table 10.1.1.0 verbose
Routing tables:
+ = Active Route, - = Last Active, # = Both * = Next hop in use
Summary count: 1
**Destination: 10.1.1.0 Mask: 255.255.255.0
Protocol: #STATIC Preference: 60
*NextHop: 192.168.0.31 Interface: 192.168.0.246(Vlan-interface1)
State: <Int ActiveU Gateway Static Unicast>
Age: 32:31 Cost: 0/0
Refer to Table 1-5 for the description on the output fields.
1.1.8 display ip routing-table ip-address1 ip-address2
Syntax
display ip routing-table ip-address1 mask1 ip-address2 mask2 [ verbose ]
View
Any view
Parameter
ip-address1, ip-address2: Destination IP addresses in dotted decimal notation. ip-address1 and mask1, together with ip-address2 and mask2, determine an IP address range. The starting address of the IP address range is determined by the ip-address1 and mask1 arguments; and the end address of the IP address range is determined by the ip-address2 and mask2 arguments.
mask1, mask2: IP address masks. These two arguments can be in dotted decimal notation or two integers ranging from 0 to 32.
verbose: Displays the detailed information about the active and inactive routes. If you do not specify this keyword, only the summary information about the active routes is displayed.
Description
Use the display ip routing-table ip-address1 ip-address2 command to display the information about the routes with their destinations within the specified destination IP address range.
Example
# Display the information about the routes with their destinations within the range of 1.1.1.0 to 2.2.2.0.
<Sysname> display ip routing-table 1.1.1.0 24 2.2.2.0 24
Routing tables:
Summary count: 1
Destination/Mask Protocol Pre Cost Nexthop Interface
1.1.1.0/24 DIRECT 0 0 1.1.1.1 Vlan-interface1
Refer to Table 1-4 for the description on the output fields.
1.1.9 display ip routing-table protocol
Syntax
display ip routing-table protocol protocol [ inactive | verbose ]
View
Any view
Parameter
protocol: This argument can be one of the following:
l direct: Displays the information about the direct routes.
l static: Displays the information about the static routes.
inactive: Displays the information about the inactive routes. If you do not specify this keyword, the information about both active and inactive routes is displayed.
verbose: Displays the detailed route information. If you do not specify this keyword, only the summary route information is displayed.
Description
Use the display ip routing-table protocol command to display the information about specified type of routes.
Example
# Display the summary information about all the direct routes.
<Sysname> display ip routing-table protocol direct
DIRECT Routing tables:
Summary count: 4
DIRECT Routing table status:<active>:
Summary count: 4
Destination/Mask Protocol Pre Cost Nexthop Interface
127.0.0.0/8 DIRECT 0 0 127.0.0.1 InLoopBack0
127.0.0.1/32 DIRECT 0 0 127.0.0.1 InLoopBack0
192.168.0.0/24 DIRECT 0 0 192.168.0.246 Vlan-interface1
192.168.0.246/32 DIRECT 0 0 127.0.0.1 InLoopBack0
DIRECT Routing table status:<inactive>:
Summary count: 0
# Display the summary information about the static routing table.
<Sysname> display ip routing-table protocol static
STATIC Routing tables:
Summary count: 1
STATIC Routing table status:<active>:
Summary count: 1
Destination/Mask Protocol Pre Cost Nexthop Interface
10.1.1.0/24 STATIC 60 0 192.168.0.31 Vlan-interface1
STATIC Routing table status:<inactive>:
Summary count: 0
Refer to Table 1-4 for the description on the output fields.
1.1.10 display ip routing-table radix
Syntax
display ip routing-table radix
View
Any view
Parameter
None
Description
Use the display ip routing-table radix command to display the information about the routes in a routing table in a hierarchical way.
Example
# Display the information about the routes in a routing table in a hierarchical way.
<Sysname> display ip routing-table radix
Radix tree for INET (2) inodes 2 routes 2:
+--8+--{127.0.0.0
+-32+--{127.0.0.1
Table 1-6 Description on the fields of the display ip routing-table radix command
Field |
Description |
INET |
Address family |
inodes |
Number of nodes |
routes |
Number of routes |
1.1.11 display ip routing-table statistics
Syntax
display ip routing-table statistics
View
Any view
Parameter
None
Description
Use the display ip routing-table statistics command to display the statistics of a routing table.
The statistics information displayed by this command includes:
l The total number of the routes
l The number of the active routes
l The number of the added routes
l The number of the routes with deleted flags
Example
# Display the statistics information about the routing table.
<Sysname> display ip routing-table statistics
Routing tables:
Proto route active added deleted
DIRECT 2 2 2 0
STATIC 0 0 0 0
Total 2 2 2 0
Table 1-7 Description on the fields of the display ip routing-table statistics command
Field |
Description |
Proto |
Routing protocol |
route |
Total number of routes |
active |
Number of the active routes that are currently in use |
added |
Number of the routes that are added to the routing table after the switch starts or the routing table is cleared last time |
deleted |
Number of the routes with deleted flags (this type of routes will be removed after a period of time) |
Total |
Total numbers of various routes |
1.1.12 display ip routing-table verbose
Syntax
display ip routing-table verbose
View
Any view
Parameter
None
Description
Use the display ip routing-table verbose command to display the detailed information about a routing table.
You can use this command to display all the routes, including the inactive and invalid routes.
Example
# Display the detailed information about the routing table.
<Sysname> display ip routing-table verbose
Routing Tables:
+ = Active Route, - = Last Active, # = Both * = Next hop in use
Destinations: 2 Routes: 2
Holddown: 0 Delete: 0 Hidden: 0
**Destination: 127.0.0.0 Mask: 255.0.0.0
Protocol: #DIRECT Preference: 0
*NextHop: 127.0.0.1 Interface: 127.0.0.1(InLoopBack0)
State: <NoAdvise Int ActiveU Retain Unicast>
Age: 57:12 Cost: 0/0
**Destination: 127.0.0.1 Mask: 255.255.255.255
Protocol: #DIRECT Preference: 0
*NextHop: 127.0.0.1 Interface: 127.0.0.1(InLoopBack0)
State: <NotInstall NoAdvise Int ActiveU Retain Gateway Unicast>
Age: 57:12 Cost: 0/0
The statistics of the routing table are displayed first, and then the detailed descriptions of each route. Table 1-5 describes the route states and Table 1-8 describes the statistics information about the routing table.
Table 1-8 Description on the fields of the display ip routing-table verbose command
Field |
Description |
Holddown |
Number of the routes that are held down |
Delete |
Number of the deleted routes |
Hidden |
Number of the hidden routes |
1.1.13 interface Vlan-interface
Syntax
interface Vlan-interface vlan-id
undo interface Vlan-interface vlan-id
View
System view
Parameter
vlan-id: ID of the management VLAN, in the range of 1 to 4094.
Description
Use the interface Vlan-interface command to create a management VLAN interface and enter management VLAN interface view.
Use the undo interface Vlan-interface command to remove the management VLAN interface.
Before creating a management VLAN interface, make sure the VLAN identified by the vlan-id argument is created and is configured as the management VLAN.
Note that:
To create the VLAN interface for the management VLAN on a switch operating as the management device in a cluster, make sure the ID of the management VLAN is consistent with that of the cluster management VLAN, that is, the vlan-id argument in the management-vlan vlan-id command when you configure the cluster management VLAN. Otherwise, the configuration fails.
Example
# Create VLAN 10 and configure it as the management VLAN. Create VLAN 10 interface and enter VLAN 10 interface view.
<Sysname> system-view
System View: return to User View with Ctrl+Z.
[Sysname] vlan 10
[Sysname-vlan10] quit
[Sysname] management-vlan 10
[Sysname] interface Vlan-interface 10
[Sysname-Vlan-interface10]
1.1.14 ip address
Syntax
ip address ip-address mask
undo ip address [ ip-address mask ]
View
VLAN interface view
Parameter
ip-address: IP address to be assigned to the management VLAN interface.
mask: Mask of the IP address to be assigned to the management VLAN interface. The mask can be in dotted decimal notation or an integer in the range of 0 to 32.
Description
Use the ip address command to assign an IP address with the mask to a management VLAN interface.
Use the undo ip address command to remove the IP address assigned to a management VLAN interface.
Related command: display interface Vlan-interface.
Example
# Assign the IP address 192.168.0.51 (with the mask 255.255.255.0) to the management VLAN interface. (Assume that VLAN 1 is the management VLAN.)
<Sysname> system-view
System View: return to User View with Ctrl+Z.
[Sysname] interface Vlan-interface 1
[Sysname-Vlan-interface1] ip address 192.168.0.51 255.255.255.0
1.1.15 ip route-static
Syntax
ip route-static ip-address { mask | mask-length } { interface-type interface-number | next-hop } [ preference preference-value ] [ reject | blackhole ] [ description text ]
undo ip route-static ip-address { mask | mask-length } [ interface-type interface-number | next-hop ] [ preference preference-value ]
View
System view
Parameter
ip-address: Destination IP address, in dotted decimal notation.
mask: IP address mask, in dotted decimal notation.
mask-length: Mask length, in the range of 0 to 32.
interface-type interface-number: Next hop outgoing interface. Currently, you can specify a NULL interface only. A null interface is a virtual interface. Packets destined for a null interface are discarded, helping to reduce system load.
next-hop: IP address of the next hop of this route, in dotted decimal notation.
preference-value: Preference of this route, in the range of 1 to 255.
reject: Specifies the route as an unreachable route. When a static route destined for a destination address is of the reject attribute, all the IP packets destined for the destination address are discarded, and the source host is informed that the destination address is unreachable.
blackhole: Specifies the route as a black hole route. When a static route destined for a destination address is of the blackhole attribute, the outgoing interface of the route is Null 0 regardless of the next hop address. All the IP packets destined for the destination address are discarded, and the source host is not informed that the destination address is unreachable.
description text: Specifies a descriptive string for the static route. The text argument is a case-sensitive string of 1 to 60 characters (including the space).
Description
Use the ip route-static command to configure a static route.
Use the undo ip route-static command to remove a static route.
By default, the system can obtain the subnet route directly connected to the router. When you configure a static route, if no preference is specified for the route, the preference defaults to 60. Note that routes with the same destinations, the same next hops, but different preferences are different routes. Among these routes, the one with least preference (which means the highest preference) is chosen to be the current route. A route configured using the ip route-static command is a reachable route if neither of the reject and blackhole keywords is specified.
Note the following when configuring a static route:
l The next hop address of a static route cannot be the VLAN interface address of the local switch.
l A static route with both its destination IP address and mask both being 0.0.0.0 is the default route. When no matched entry is found in the routing table, a received packet is forwarded according to the default route.
Related command: display ip routing-table.
Example
# Configure the next hop of the default route as 129.102.0.2.
<Sysname> system-view
System View: return to User View with Ctrl+Z.
[Sysname] ip route-static 0.0.0.0 0.0.0.0 129.102.0.2
1.1.16 management-vlan
Syntax
management-vlan vlan-id
undo management-vlan
View
System view
Parameter
vlan-id: ID of the management VLAN, in the range of 1 to 4094.
Description
Use the management-vlan command to configure a VLAN as the management VLAN.
Use the undo management vlan command to restore the default.
VLAN 1 is the default management VLAN.
Example
# Configure VLAN 2 as the management VLAN.
<Sysname> system-view
System View: return to User View with Ctrl+Z.
[Sysname] management-vlan 2
1.1.17 reset ip routing-table statistics protocol
Syntax
reset ip routing-table statistics protocol { all | protocol }
View
User view
Parameter
all: Specifies all protocols.
protocol: Specifies a protocol, which can be static, or direct.
Description
Use the reset ip routing-table statistics protocol command to clear the statistics of routes in a routing table.
Example
# Before executing the reset ip routing-table statistics protocol command, use the display ip routing-table statistics command to display the routing statistics:
<Sysname> display ip routing-table statistics
Routing tables:
Proto route active added deleted
DIRECT 4 4 24 20
STATIC 0 0 1 1
Total 4 4 25 21
# Clear the routing statistics of all protocols from the IP routing table.
<Sysname> reset ip routing-table statistics protocol all
This will erase the specific routing counters information.
Are you sure?[Y/N]y
# Display the routing statistics in the IP routing table.
<Sysname> display ip routing-table statistics
Routing tables:
Proto route active added deleted
DIRECT 4 4 0 0
STATIC 0 0 0 0
Total 4 4 0 0
The above information shows that the routing statistics in the IP routing table is cleared.