• 产品与解决方案
  • 行业解决方案
  • 服务
  • 支持
  • 合作伙伴
  • 新华三人才研学中心
  • 关于我们

20-WLAN配置指导

13-802.11r配置

本章节下载 13-802.11r配置  (216.52 KB)

docurl=/cn/Service/Document_Software/Document_Center/Switches/Catalog/S7500E/S7500E-XS/Configure/Operation_Manual/H3C_S7500E-XS_CG-R7536P02-6W100/20/201704/982758_30005_0.htm

13-802.11r配置


1 802.11r

1.1  简介

802.11r协议中定义的FT(Fast BSS Transition,快速BSS切换)功能用来减少客户端在漫游过程中的时间延迟,从而降低连接中断概率、提高漫游服务质量。

1.1.1  FT实现方式

FT支持两种方式:

·     Over-the-Air:客户端直接与目标AP通信,进行漫游前的认证。

·     Over-the-DS:客户端通过当前AP与目标AP通信,进行漫游前的认证。

1. AC内over-the-air方式漫游

图1-1 AC内over-the-air方式漫游示意图

 

图1-1所示,客户端在连接至同一AC的AP间(AP 1到AP 2)漫游时,信息交互过程描述如下:

(1)     客户端已经与AP 1连接并且要漫游到AP 2;

(2)     客户端向AP 2发送认证请求;

(3)     客户端收到AP 2的认证请求回应;

(4)     客户端向AP 2发送重关联请求;

(5)     客户端收到AP 2的重关联请求回应;

(6)     客户端完成从AP 1到AP 2的漫游。

2. AC间over-the-air方式漫游

图1-2 AC间over-the-air方式漫游示意图

 

图1-2所示,AP 1和AP 2分别连接AC 1和AC 2,在同一移动域内漫游的信息交互过程描述如下:

(1)     客户端与AP 1建立连接;

(2)     AC 1同步客户端漫游信息(PMK、VLAN等信息)到AC 2;

(3)     客户端准备漫游,发送FT认证请求到AP 2;

(4)     客户端收到AP 2发送的FT认证回复;

(5)     客户端向AP 2发送重关联请求;

(6)     客户端收到AP 2的重关联请求回应;

(7)     客户端完成从AP 1到AP 2的漫游。

3. AC内over-the-ds方式漫游

图1-3 AC内over-the-ds方式漫游示意图

 

图1-3所示,客户端在连接至同一AC的AP间(AP 1到AP 2)漫游时,信息交互过程描述如下:

(1)     客户端与AP 1建立连接;

(2)     AC生成、同步、保存客户端的漫游表项;

(3)     客户端准备漫游,向AP 1发送FT认证请求;

(4)     客户端收到AP 1的FT认证回复;

(5)     客户端向AP 2发送重关联请求;

(6)     客户端收到AP 2的重关联请求回应;

(7)     客户端完成从AP 1到AP 2的漫游。

1.1.2  标准与协议

·     802.11r IEEE Standard for Information technology—Telecommunications and information exchange between systems—Local and metropolitan area networks—Specific requirements

1.1.3  注意事项

·     如果有客户端无法关联使能了FT功能的服务,可能是由于客户端的型号较早而不支持FT协议。此时可以创建两个SSID相同的服务,一个使能FT功能,另一个不使能FT功能,而其它配置均相同,以便客户端可以正常使用网络服务。

·     不建议在服务模板下同时开启FT功能和802.1X周期性重认证功能,否则会导致客户端在每次重认证时间间隔到达时重新上线。关于802.1X周期性重认证功能的介绍和配置请参见“WLAN配置指导”中的“WLAN用户接入认证”。

1.2  802.11r配置

表1-1 配置802.11r

操作

命令

说明

进入系统视图

system-view

-

配置WLAN服务模板

wlan service-template service-template-name

-

开启FT功能

ft enable

缺省情况下,FT功能处于关闭状态

(可选)配置FT方式

ft method { over-the-air | over-the-ds }

缺省情况下,FT方式为over-the-air

(可选)配置关联超时时间

ft reassociation-timeout timeout

缺省情况下,关联超时时间为20秒

关联超时时间指的是,客户端在完成认证后,客户端发起关联请求的最大时间间隔。如果在此时间内客户端没有发起关联,则会终止此次漫游

 

1.3  802.11r典型配置举例

1.3.1  FT Over-the-DS方式PSK模式配置举例

1. 组网需求

图1-4所示,客户端在AC内的不同AP间进行漫游,使用Over-the-DS方式,通过PSK模式对客户端进行身份认证与密钥管理。

2. 组网图

图1-4 FT Over-the-DS方式PSK身份认证与密钥管理模式配置组网图

 

3. 配置步骤

# 创建无线服务模板acstname。

<AC> system-view

[AC] wlan service-template acstname

# 配置无线服务的SSID为service。

[AC-wlan-st-acstname] ssid service

# 配置身份认证与密钥管理的模式是PSK模式,配置使用明文字符串12345678作为PSK密钥。

[AC-wlan-st-acstname] akm mode psk

[AC-wlan-st-acstname] preshared-key pass-phrase simple 12345678

# 配置AES-CCMP加密套件,配置在AP发送信标和探查响应帧时携带RSN IE。

[AC-wlan-st-acstname] cipher-suite ccmp

[AC-wlan-st-acstname] security-ie rsn

# 开启FT功能。

[AC-wlan-st-acstname] ft enable

# 配置重关联超时时间为50秒。

[AC-wlan-st-acstname] ft reassociation-timeout 50

# 配置FT方式为Over-the-DS。

[AC-wlan-st-acstname] ft method over-the-ds

# 使能无线服务。

[AC-wlan-st-acstname] service-template enable

[AC-wlan-st-acstname] quit

# 创建AP,名称为1,并将无线服务模板acstname绑定到AP 1的Radio2上。

[AC] wlan ap 1

[AC-wlan-ap-1] radio 2

[AC-wlan-ap-1-radio-2] service-template acstname

[AC-wlan-ap-1-radio-2] radio enable

[AC-wlan-ap-1-radio-2] quit

[AC-wlan-ap-1] quit

# 创建AP,名称为2,并将无线服务模板acstname绑定到AP 2的Radio2上。

[AC] wlan ap 2

[AC-wlan-ap-2] radio 2

[AC-wlan-ap-2-radio-2] service-template acstname

[AC-wlan-ap-2-radio-2] radio enable

[AC-wlan-ap-2-radio-2] quit

[AC-wlan-ap-2] quit

4. 验证配置

# 在AC上通过display wlan service-template命令可以查看服务模板的配置情况。

[AC] display wlan service-template acstname verbose

Service template name        : acstname

SSID                         : service

SSID-hide                    : Disabled

User-isolation               : Disabled

Service template status      : Enabled

Maximum clients per BSS      : Not configured

Frame format                 : Dot3

Seamless-roam                : Disabled

Seamless-roam RSSI threshold : 50

Seamless-roam RSSI gap       : 20

VLAN ID                      : 1

AKM mode                     : PSK

Security IE                  : RSN

Cipher suite                 : CCMP

TKIP countermeasure time     : 0 sec

PTK lifetime                 : 43200 sec

GTK rekey                    : Enabled

GTK rekey method             : Time-based

GTK rekey time               : 86400 sec

GTK rekey client-offline     : Disabled

User authentication mode     : Bypass

Intrusion protection         : Disabled

Intrusion protection mode    : Temporary-block

Temporary block time         : 180 sec

Temporary service stop time  : 20 sec

Fail VLAN ID                 : Not configured

802.1X handshake             : Disabled

802.1X handshake secure      : Disabled

802.1X domain                : Not configured

MAC-auth domain              : Not configured

Max 802.1X users             : 4096

Max MAC-auth users           : 4096

802.1X re-authenticate       : Disabled

Authorization fail mode      : Online

Accounting fail mode         : Online

Authorization                : Permitted

Key derivation               : SHA1

PMF status                   : Disabled

Hotspot policy number        : Not configured

Forward policy               : Not configured

Forwarder                    : AC

FT Status                    : Enable

FT Method                    : over-the-ds

FT Reassociation Deadline    : 50 sec

QoS trust                    : Port

QoS priority                 : 0

# 客户端上线后,在AC上通过display wlan client verbose命令可以查看客户端的详细信息。

[AC] display wlan client verbose

Total number of clients: 1

 

MAC address                       : fc25-3f03-8361

IPv4 address                      : 10.1.1.114

IPv6 address                      : N/A

Username                          : N/A

AID                               : 1

AP ID                             : 1

AP name                           : 1

Radio ID                          : 2

SSID                              : service

BSSID                             : 000f-e266-7788

VLAN ID                           : 1

Power save mode                   : Active

Wireless mode                     : 802.11gn

Channel bandwidth                 : 20MHz

SM power save                     : Enabled

SM power save mode                : Static

Short GI for 20MHz                : Not supported

Short GI for 40MHz                : Not supported

STBC RX capability                : Supported

STBC TX capability                : Not supported

Support HT-MCS set                : 0, 1, 2, 3, 4, 5, 6, 7

QoS mode                          : WMM

Listen interval                   : 20

RSSI                              : 0

Rx/Tx rate                        : 65/65

Authentication method             : Open system

Security mode                     : RSN

AKM mode                          : PSK

Encryption cipher                 : CCMP

User authentication mode          : Bypass

Authorization ACL ID              : N/A

Authorization user profile        : N/A

Roam status                       : N/A

Key derivation                    : SHA256

PMF status                        : N/A

Forward policy                    : N/A

Online time                       : 0hr 0min 41sec

FT status                         : Active

# 客户端漫游成功后,在AC上通过display wlan client verbose命令,可以看到结果如下。

[AC] display wlan client verbose

Total number of clients: 1

 

 MAC address                       : fc25-3f03-8361

 IPv4 address                      : 10.1.1.114

 IPv6 address                      : N/A

 Username                          : N/A

 AID                               : 1

 AP ID                             : 2

 AP name                           : 2

 Radio ID                          : 2

 SSID                              : service

 BSSID                             : 000f-e211-2233

 VLAN ID                           : 1

 Power save mode                   : Active

 Wireless mode                     : 802.11gn

 Channel bandwidth                 : 20MHz

 SM power save                     : Enabled

 SM power save mode                : Static

 Short GI for 20MHz                : Not supported

 Short GI for 40MHz                : Not supported

 STBC RX capability                : Supported

 STBC TX capability                : Not supported

 Support HT-MCS set                : 0, 1, 2, 3, 4, 5, 6, 7

 QoS mode                          : WMM

 Listen interval                   : 20

 RSSI                              : 0

 Rx/Tx rate                        : 0/0

 Authentication method             : FT

 Security mode                     : RSN

 AKM mode                          : PSK

 Encryption cipher                 : CCMP

 User authentication mode          : Bypass

 Authorization ACL ID              : N/A

 Authorization user profile        : N/A

 Roam status                       : Intra-AC roam

 Key derivation                    : SHA256

 PMF status                        : N/A

 Forward policy                    : N/A

 Online time                       : 0hr 0min 27sec

 FT status                         : Active

1.3.2  FT Over-the-Air方式PSK模式配置举例

1. 组网需求

图1-4所示,客户端在AC内的不同AP间进行漫游,使用Over-the-Air方式,通过PSK模式对客户端进行身份认证与密钥管理。

2. 配置步骤

# 创建无线服务模板acstname。

<AC> system-view

[AC] wlan service-template acstname

# 配置无线服务的SSID为service。

[AC-wlan-st-acstname] ssid service

# 配置身份认证与密钥管理的模式是PSK模式,配置使用明文字符串12345678作为PSK密钥。

[AC-wlan-st-acstname] akm mode psk

[AC-wlan-st-acstname] preshared-key pass-phrase simple 12345678

# 配置AES-CCMP加密套件,配置在AP发送信标和探查响应帧时携带RSN IE。

[AC-wlan-st-acstname] cipher-suite ccmp

[AC-wlan-st-acstname] security-ie rsn

# 开启FT功能。

[AC-wlan-st-acstname] ft enable

# 配置重关联超时时间为50秒。

[AC-wlan-st-acstname] ft reassociation-timeout 50

# 使能无线服务模板。

[AC-wlan-st-acstname] service-template enable

[AC-wlan-st-acstname] quit

# 创建AP,名称为1,并将无线服务模板acstname绑定到AP 1的Radio2上。

[AC] wlan ap 1

[AC-wlan-ap-1] radio 2

[AC-wlan-ap-1-radio-2] service-template acstname

[AC-wlan-ap-1-radio-2] radio enable

[AC-wlan-ap-1-radio-2] quit

[AC-wlan-ap-1] quit

# 创建AP,名称为2,并将无线服务模板acstname绑定到AP 2的Radio2上。

[AC] wlan ap 2

[AC-wlan-ap-2] radio 2

[AC-wlan-ap-2-radio-2] service-template acstname

[AC-wlan-ap-2-radio-2] radio enable

[AC-wlan-ap-2-radio-2] quit

[AC-wlan-ap-2] quit

3. 验证配置

# 客户端上线后,在AC通过display wlan client verbose命令可以看到结果如下。

[AC] display wlan client verbose

Total number of clients: 1

 

MAC address                       : fc25-3f03-8361

IPv4 address                      : 10.1.1.114

IPv6 address                      : N/A

Username                          : N/A

AID                               : 1

AP ID                             : 1

AP name                           : 1

Radio ID                          : 2

SSID                              : service

BSSID                             : 000f-e266-7788

VLAN ID                           : 1

Power save mode                   : Active

Wireless mode                     : 802.11gn

Channel bandwidth                 : 20MHz

SM power save                     : Enabled

SM power save mode                : Static

Short GI for 20MHz                : Not supported

Short GI for 40MHz                : Not supported

STBC RX capability                : Supported

STBC TX capability                : Not supported

Support HT-MCS set                : 0, 1, 2, 3, 4, 5, 6, 7

QoS mode                          : WMM

Listen interval                   : 20

RSSI                              : 0

Rx/Tx rate                        : 65/65

Authentication method             : Open system

Security mode                     : RSN

AKM mode                          : PSK

Encryption cipher                 : CCMP

User authentication mode          : Bypass

Authorization ACL ID              : N/A

Authorization user profile        : N/A

Roam status                       : N/A

Key derivation                    : SHA256

PMF status                        : N/A

Forward policy                    : N/A

Online time                       : 0hr 0min 41sec

FT status                         : Active

# 客户端漫游成功后,在AC上通过display wlan client verbose命令可以看到结果如下。

[AC] display wlan client verbose

Total number of clients: 1

 

 MAC address                       : fc25-3f03-8361

 IPv4 address                      : 10.1.1.114

 IPv6 address                      : N/A

 Username                          : N/A

 AID                               : 1

 AP ID                             : 2

 AP name                           : 2

 Radio ID                          : 2

 SSID                              : service

 BSSID                             : 000f-e211-2233

 VLAN ID                           : 1

 Power save mode                   : Active

 Wireless mode                     : 802.11gn

 Channel bandwidth                 : 20MHz

 SM power save                     : Enabled

 SM power save mode                : Static

 Short GI for 20MHz                : Not supported

 Short GI for 40MHz                : Not supported

 STBC RX capability                : Supported

 STBC TX capability                : Not supported

 Support HT-MCS set                : 0, 1, 2, 3, 4, 5, 6, 7

 QoS mode                          : WMM

 Listen interval                   : 20

 RSSI                              : 0

 Rx/Tx rate                        : 0/0

 Authentication method             : FT

 Security mode                     : RSN

 AKM mode                          : PSK

 Encryption cipher                 : CCMP

 User authentication mode          : Bypass

 Authorization ACL ID              : N/A

 Authorization user profile        : N/A

 Roam status                       : Intra-AC roam

 Key derivation                    : SHA256

 PMF status                        : N/A

 Forward policy                     : N/A

 Online time                       : 0hr 0min 27sec

 FT status                         : Active

1.3.3  FT Over-the-DS方式802.1X模式配置举例

1. 组网需求

图1-4所示,客户端在AC内的不同AP间进行漫游,使用Over-the-DS方式,通过802.1X模式对客户端进行身份认证与密钥管理。

2. 配置步骤

# 创建无线服务模板stname。

<AC> system-view

[AC] wlan service-template stname

# 配置无线服务的SSID为service。

[AC-wlan-st-stname] ssid service

# 配置身份认证与密钥管理的模式是802.1X模式。

[AC-wlan-st-stname] akm mode dot1x

# 配置AES-CCMP加密套件,配置在AP发送信标和探查响应帧时携带RSN IE。

[AC-wlan-st-stname] cipher-suite ccmp

[AC-wlan-st-stname] security-ie rsn

# 配置客户端安全认证方式为802.1X。

[AC-wlan-st-stname] client-security authentication-mode dot1x

[AC-wlan-st-stname] dot1x domain imc

# 开启FT功能。

[AC-wlan-st-stname] ft enable

# 配置FT方法为Over-the-DS。

[AC-wlan-st-stname] ft method over-the-ds

# 使能无线服务。

[AC-wlan-st-stname] service-template enable

[AC-wlan-st-stname] quit

# 配置802.1X认证方式为EAP。

[AC] dot1x authentication-method eap

# 创建RADIUS方案imcc。配置主认证服务器的IP地址为10.1.1.3,与认证服务器交互报文时的共享密钥为明文12345678。配置主计费服务器的IP地址为10.1.1.3,与计费服务器交互报文时的共享密钥为明文12345678。配置发送给RADIUS服务器的用户名不带ISP域名。

[AC] radius scheme imcc

[AC-radius-imcc] primary authentication 10.1.1.3

[AC-radius-imcc] primary accounting 10.1.1.3

[AC-radius-imcc] key authentication simple 12345678

[AC-radius-imcc] key accounting simple 12345678

[AC-radius-imcc] user-name-format without-domain

[AC-radius-imcc] quit

# 创建认证域并配置使用RADIUS方案进行认证、授权、计费。

[AC] domain imc

[AC-isp-imc] authentication lan-access radius-scheme imcc

[AC-isp-imc] authorization lan-access radius-scheme imcc

[AC-isp-imc] accounting lan-access radius-scheme imcc

[AC-isp-imc] quit

# 创建AP,名称为1,并将无线服务模板acstname绑定到AP 1的Radio2上。

[AC] wlan ap 1

[AC-wlan-ap-1] radio 2

[AC-wlan-ap-1-radio-2] service-template acstname

[AC-wlan-ap-1-radio-2] radio enable

[AC-wlan-ap-1-radio-2] quit

[AC-wlan-ap-1] quit

# 创建AP,名称为2,并将无线服务模板acstname绑定到AP 2的Radio2上。

[AC] wlan ap 2

[AC-wlan-ap-2] radio 2

[AC-wlan-ap-2-radio-2] service-template acstname

[AC-wlan-ap-2-radio-2] radio enable

[AC-wlan-ap-2-radio-2] quit

[AC-wlan-ap-2] quit

3. 验证配置

# 在AC上通过display wlan service-template命令可以查看服务模板的配置情况。

[AC] display wlan service-template stname verbose

Service template name        : stname

SSID                         : service

SSID-hide                    : Disabled

User-isolation               : Disabled

Service template status      : Enabled

Maximum clients per BSS      : Not configured

Frame format                 : Dot3

Seamless-roam                : Disabled

Seamless-roam RSSI threshold : 50

Seamless-roam RSSI gap       : 20

VLAN ID                      : 1

AKM mode                     : 802.1X

Security IE                  : RSN

Cipher suite                 : CCMP

TKIP countermeasure time     : 0 sec

PTK lifetime                 : 43200 sec

GTK rekey                    : Enabled

GTK rekey method             : Time-based

GTK rekey time               : 86400 sec

GTK rekey client-offline     : Disabled

User authentication mode     : 802.1X

Intrusion protection         : Disabled

Intrusion protection mode    : Temporary-block

Temporary block time         : 180 sec

Temporary service stop time  : 20 sec

Fail VLAN ID                 : Not configured

802.1X handshake             : Disabled

802.1X handshake secure      : Disabled

802.1X domain                : imc

MAC-auth domain              : Not configured

Max 802.1X users             : 4096

Max MAC-auth users           : 4096

802.1X re-authenticate       : Disabled

Authorization fail mode      : Online

Accounting fail mode         : Online

Authorization                : Permitted

Key derivation               : SHA1

PMF status                   : Disabled

Hotspot policy number        : Not configured

Forward policy               : Not configured

Forwarder                    : AC

FT Status                    : Enable

FT Method                    : over-the-ds

FT Reassociation Deadline    : 20 sec

QoS trust                    : Port

QoS priority                 : 0

# 客户端上线后,在AC上通过display wlan client verbose命令可以看到结果如下。

[AC] display wlan client verbose

Total number of clients: 1

 

MAC address                       : fc25-3f03-8361

IPv4 address                      : 10.1.1.114

IPv6 address                      : N/A

Username                          : w2

AID                               : 1

AP ID                             : 1

AP name                           : 1

Radio ID                          : 2

SSID                              : service

BSSID                             : 000f-e266-7788

VLAN ID                           : 1

Power save mode                   : Active

Wireless mode                     : 802.11gn

Channel bandwidth                 : 20MHz

SM power save                     : Enabled

SM power save mode                : Static

Short GI for 20MHz                : Not supported

Short GI for 40MHz                : Not supported

STBC RX capability                : Supported

STBC TX capability                : Not supported

Support HT-MCS set                : 0, 1, 2, 3, 4, 5, 6, 7

QoS mode                          : WMM

Listen interval                   : 20

RSSI                              : 0

Rx/Tx rate                        : 0/0

Authentication method             : Open system

Security mode                     : RSN

AKM mode                          : 802.1X

Encryption cipher                 : CCMP

User authentication mode          : 802.1X

Authorization ACL ID              : N/A

Authorization user profile        : N/A

Roam status                       : N/A

Key derivation                    : SHA256

PMF status                        : N/A

Forward policy                    : N/A

Online time                       : 0hr 0min 7sec

FT status                         : Active

# 客户端漫游成功后,在AC上通过display wlan client verbose命令可以看到结果如下。

[AC] display wlan client verbose

Total number of clients: 1

 

MAC address                       : fc25-3f03-8361

IPv4 address                      : 10.1.1.114

IPv6 address                      : N/A

Username                          : w2

AID                               : 1

AP ID                             : 2

AP name                           : 2

Radio ID                          : 2

SSID                              : service

BSSID                             : 000f-e211-2233

VLAN ID                           : 1

Power save mode                   : Active

Wireless mode                     : 802.11gn

Channel bandwidth                 : 20MHz

SM power save                     : Enabled

SM power save mode                : Static

Short GI for 20MHz                : Not supported

Short GI for 40MHz                : Not supported

STBC RX capability                : Supported

STBC TX capability                : Not supported

Support HT-MCS set                : 0, 1, 2, 3, 4, 5, 6, 7

QoS mode                          : WMM

Listen interval                   : 20

RSSI                              : 0

Rx/Tx rate                        : 0/0

Authentication method             : FT

Security mode                     : RSN

AKM mode                          : 802.1X

Encryption cipher                 : CCMP

User authentication mode          : 802.1X

Authorization ACL ID              : N/A

Authorization user profile        : N/A

Roam status                       : Intra-AC roam

Key derivation                    : SHA256

PMF status                        : N/A

Forward policy                    : N/A

Online time                       : 0hr 0min 7sec

FT status                         : Active

1.3.4  FT Over-the-Air方式802.1X模式配置举例

1. 组网需求

图1-4所示,客户端在AC内的不同AP间进行漫游,使用Over-the-Air方式,通过802.1X模式对客户端进行身份认证与密钥管理。

2. 配置步骤

# 创建无线服务模板stname。

<AC> system-view

[AC]wlan service-template stname

# 配置无线服务的SSID为service。

[AC-wlan-st-stname] ssid service

# 配置身份认证与密钥管理的模式是802.1X模式。

[AC-wlan-st-stname] akm mode dot1x

# 配置AES-CCMP加密套件,配置在AP发送信标和探查响应帧时携带RSN IE。

[AC-wlan-st-stname] cipher-suite ccmp

[AC-wlan-st-stname] security-ie rsn

# 配置客户端安全认证方式为802.1X。

[AC-wlan-st-stname] client-security authentication-mode dot1x

[AC-wlan-st-stname] dot1x domain imc

# 开启FT功能。

[AC-wlan-st-stname] ft enable

# 使能无线服务。

[AC-wlan-st-stname] service-template enable

[AC-wlan-st-stname] quit

# 配置802.1X认证方式为EAP。

[AC] dot1x authentication-method eap

# 创建RADIUS方案imcc。配置主认证服务器的IP地址为10.1.1.3,与认证服务器交互报文时的共享密钥为明文12345678。配置主计费服务器的IP地址为10.1.1.3,与计费服务器交互报文时的共享密钥为明文12345678。配置发送给RADIUS服务器的用户名不带ISP域名。

[AC] radius scheme imcc

[AC-radius-imcc] primary authentication 10.1.1.3

[AC-radius-imcc] primary accounting 10.1.1.3

[AC-radius-imcc] key authentication simple 12345678

[AC-radius-imcc] key accounting simple 12345678

[AC-radius-imcc] user-name-format without-domain

[AC-radius-imcc] quit

# 创建认证域并配置使用RADIUS方案进行认证、授权、计费。

[AC] domain imc

[AC-isp-imc] authentication lan-access radius-scheme imcc

[AC-isp-imc] authorization lan-access radius-scheme imcc

[AC-isp-imc] accounting lan-access radius-scheme imcc

[AC-isp-imc] quit

# 创建AP,名称为1,并将无线服务模板acstname绑定到AP 1的Radio2上。

[AC] wlan ap 1

[AC-wlan-ap-1] radio 2

[AC-wlan-ap-1-radio-2] service-template acstname

[AC-wlan-ap-1-radio-2] radio enable

[AC-wlan-ap-1-radio-2] quit

[AC-wlan-ap-1] quit

# 创建AP,名称为2,并将无线服务模板acstname绑定到AP 2的Radio2上。

[AC] wlan ap 2

[AC-wlan-ap-2] radio 2

[AC-wlan-ap-2-radio-2] service-template acstname

[AC-wlan-ap-2-radio-2] radio enable

[AC-wlan-ap-2-radio-2] quit

[AC-wlan-ap-2] quit

3. 验证配置

# 客户端上线后,在AC上通过display wlan client verbose命令可以看到结果如下。

[AC] display wlan client verbose

Total number of clients: 1

 

MAC address                       : fc25-3f03-8361

IPv4 address                      : 10.1.1.114

IPv6 address                      : N/A

Username                          : w2

AID                               : 1

AP ID                             : 1

AP name                           : 1

Radio ID                          : 2

SSID                              : service

BSSID                             : 000f-e266-7788

VLAN ID                           : 1

Power save mode                   : Active

Wireless mode                     : 802.11gn

Channel bandwidth                 : 20MHz

SM power save                     : Enabled

SM power save mode                : Static

Short GI for 20MHz                : Not supported

Short GI for 40MHz                : Not supported

STBC RX capability                : Supported

STBC TX capability                : Not supported

Support HT-MCS set                : 0, 1, 2, 3, 4, 5, 6, 7

QoS mode                          : WMM

Listen interval                   : 20

RSSI                              : 0

Rx/Tx rate                        : 0/0

Authentication method             : Open system

Security mode                     : RSN

AKM mode                          : 802.1X

Encryption cipher                 : CCMP

User authentication mode          : 802.1X

Authorization ACL ID              : N/A

Authorization user profile        : N/A

Roam status                       : N/A

Key derivation                    : SHA256

PMF status                        : N/A

Forward policy                    : N/A

Online time                       : 0hr 0min 19sec

FT status                         : Active

# 客户端漫游成功后,在AC上通过display wlan client verbose命令可以看到结果如下。

[AC] display wlan client verbose

Total number of clients: 1

 

MAC address                       : fc25-3f03-8361

IPv4 address                      : 10.1.1.114

IPv6 address                      : N/A

Username                          : w2

AID                               : 1

AP ID                             : 2

AP name                           : 2

Radio ID                          : 2

SSID                              : service

BSSID                             : 000f-e211-2233

VLAN ID                           : 1

Power save mode                   : Active

Wireless mode                     : 802.11gn

Channel bandwidth                 : 20MHz

SM power save                     : Enabled

SM power save mode                : Static

Short GI for 20MHz                : Not supported

Short GI for 40MHz                : Not supported

STBC RX capability                : Supported

STBC TX capability                : Not supported

Support HT-MCS set                : 0, 1, 2, 3, 4, 5, 6, 7

QoS mode                          : WMM

Listen interval                   : 20

RSSI                              : 0

Rx/Tx rate                        : 0/0

Authentication method             : FT

Security mode                     : RSN

AKM mode                          : 802.1X

Encryption cipher                 : CCMP

User authentication mode          : 802.1X

Authorization ACL ID              : N/A

Authorization user profile        : N/A

Roam status                       : Intra-AC roam

Key derivation                    : SHA256

PMF status                        : N/A

Forward policy                    : N/A

Online time                       : 0hr 0min 7sec

FT status                         : Active

 

不同款型规格的资料略有差异, 详细信息请向具体销售和400咨询。H3C保留在没有任何通知或提示的情况下对资料内容进行修改的权利!

新华三官网
联系我们