10-High Availability Command Reference

HomeSupportReference GuidesCommand ReferencesH3C S12500X-AF & S12500-X & S9800 Switch Series Command References(R27xx)-6W10510-High Availability Command Reference
12-Reth interface and redundancy group commands
Title Size Download
12-Reth interface and redundancy group commands 150.58 KB

Reth interface commands

The Reth interface feature is supported only in IRF mode.

bandwidth

Use bandwidth to set the expected bandwidth for a Reth interface.

Use undo bandwidth to restore the default.

Syntax

bandwidth bandwidth-value

undo bandwidth

Default

The expected bandwidth is 10000 kbps for a Reth interface.

Views

Reth interface view

Predefined user roles

network-admin

mdc-admin

Parameters

bandwidth-value: Specifies the expected bandwidth in the range of 1 to 400000000 kbps.

Usage guidelines

The expected bandwidth is an informational parameter used only by higher-layer protocols for calculation. You cannot adjust the actual bandwidth of an interface by using this command.

Examples

# Set the expected bandwidth to 50 kbps for Reth 1.

<Sysname> system-view

[Sysname] interface reth 1

[Sysname-Reth1] bandwidth 50

default

Use default to restore the default settings for a Reth interface.

Syntax

default

Views

Reth interface view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

CAUTION

CAUTION:

The default command might interrupt ongoing network services. Make sure you are fully aware of the impacts of this command when you execute it on a live network.

 

This command might fail to restore the default settings for some commands for reasons such as command dependencies and system restrictions.

To resolve this problem:

1.     Use the display this command in interface view to identify these commands.

2.     Use their undo forms or follow the command reference to restore their default settings.

3.     If the restoration attempt still fails, follow the error message instructions to resolve the problem.

Examples

# Restore the default settings for Reth 1.

<Sysname> system-view

[Sysname] interface reth 1

[Sysname-Reth1] default

description

Use description to configure the description of an interface.

Use undo description to restore the default.

Syntax

description text

undo description

Default

The description of a Reth interface is interface-name plus Interface (for example, Reth1 Interface).

Views

Reth interface view

Predefined user roles

network-admin

mdc-admin

Parameters

text: Specifies a description, a case-sensitive string of 1 to 255 characters.

Examples

# Configure the description of Reth 1 as master-interface.

<Sysname> system-view

[Sysname] interface reth 1

[Sysname-Reth1] description master-interface

display interface reth

Use display interface reth to display Reth interface information.

Syntax

display interface [ reth [ interface-number ] ] [ brief [ description | down ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

reth [ interface-number ]: Specifies Reth interfaces. The interface-number argument specifies an existing Reth interface by its number. If you do not specify the reth keyword, the command displays information about all interfaces. If you specify the reth keyword without the interface-number argument, the command displays information about all Reth interfaces.

brief: Displays brief interface information. If you do not specify this keyword, the command displays detailed interface information.

down: Displays information about interfaces in down state and the causes for the down state. If you do not specify this keyword, the command displays information about interfaces in all states.

description: Displays complete interface descriptions. If you do not specify this keyword, the command displays only the first 27 characters of each interface description.

Examples

# Display detailed information about Reth 1.

<Sysname> display interface reth 1

Reth1

Current state: UP

Line protocol state: UP

Description: Reth1 Interface

Bandwidth: 10000kbps

Maximum transmission unit: 1500

Internet protocol processing: Disabled

IP packet frame type: Ethernet II, hardware address: 0cda-41b5-cf30

IPv6 packet frame type: Ethernet II, hardware address: 0cda-41b5-cf30

Physical: Reth, baudrate: 10000000 bps

Last clearing of counters: Never

Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Input: 0 packets, 0 bytes, 0 drops

Output: 0 packets, 0 bytes, 0 drops

Table 1 Command output

Field

Description

Current state

Physical link state of the interface:

·     Administratively DOWN—The interface has been shut down by using the shutdown command.

·     DOWN—The interface is administratively up, but its physical state is down (possibly because no physical link exists or the link has failed).

·     UP—The interface is both administratively and physically up. A Reth interface is both administratively and physically up when a minimum of one member interface is administratively and physically up.

Line protocol state

Data link layer state of the interface. The state is determined through automatic parameter negotiation at the data link layer.

·     UP—The data link layer protocol is up.

·     DOWN—The data link layer protocol is down.

Description

Description of the interface.

Bandwidth

Expected bandwidth of the interface.

Maximum transmission unit

MTU of the interface.

Internet protocol processing: Disabled

The interface is not assigned an IP address and cannot process IP packets.

Internet Address

IP address of the interface. The primary attribute indicates that the address is the primary IP address.

IP packet frame type

IPv4 packet framing format.

hardware address

MAC address of the interface.

IPv6 packet frame type

IPv6 packet framing format.

Physical

Interface type.

Last clearing of counters

Last time when the reset counters interface command was used to clear the interface statistics.

If the reset counters interface command has never been used on the interface since the device startup, this field displays Never.

Last 300 second input:  0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 second output:  0 bytes/sec, 0 bits/sec, 0 packets/sec

Average incoming and outgoing traffic rate for the last 300 seconds.

Input: 0 packets, 0 bytes, 0 drops

Incoming traffic statistics on the interface:

·     Number of packets.

·     Number of bytes.

·     Number of dropped packets due to insufficient receive buffer.

Output: 0 packets, 0 bytes, 0 drops

Outgoing traffic statistics on the interface:

·     Number of packets.

·     Number of bytes.

·     Number of dropped packets due to insufficient send buffer.

Brief information on interfaces in route mode

Brief information about Layer 3 interfaces.

Interface

Abbreviated interface name.

Link

Physical link state of the interface:

·     UP—The interface is physically up.

·     DOWN—The interface is physically down.

·     ADM—The interface has been shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command.

·     Stby—The interface is a backup interface in standby state. To see the primary interface, use the display interface-backup state command.

Protocol

Data link layer protocol state of the interface:

·     UP—The data link layer protocol of the interface is up.

·     DOWN—The data link layer protocol of the interface is down.

·     UP(s)—The data link layer protocol of the interface is up, but the link is an on-demand link or does not exist. The (s) attribute represents the spoofing flag.

Primary IP

Primary IP address of the interface. This field displays two hyphens (--) if the interface does not have an IP address.

Description

Description of the interface.

 

# Display brief information about Reth 1.

<Sysname> display interface reth 1 brief

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface            Link Protocol Primary IP         Description

Reth1                DOWN DOWN     --

# Display the causes for the down state of Reth 1.

<Sysname> display interface reth 1 brief down

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Interface            Link Cause

Reth1                DOWN Not connected

Table 2 Command output

Field

Description

Brief information on interfaces in route mode:

Brief information about Layer 3 interfaces.

Interface

Interface name.

Link

Physical link state of the interface:

·     UP—The interface is physically up.

·     DOWN—The interface is physically down.

·     ADM—The interface has been shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command.

·     Stby—The interface is a backup interface in standby state. To see the primary interface, use the display interface-backup state command.

Protocol

Data link layer protocol state of the interface:

·     UP—The data link layer protocol of the interface is up.

·     DOWN—The data link layer protocol of the interface is down.

·     UP(s)—The data link layer protocol of the interface is up, but the link is an on-demand link or does not exist. The (s) attribute represents the spoofing flag. This value is typical of null interfaces and loopback interfaces.

Primary IP

Primary IP address of the interface. This field displays two hyphens (--) if the interface does not have an IP address.

Description

Description of the interface.

Cause

Cause for the physical link state of an interface to be DOWN:

·     Administratively—The interface has been manually shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command.

·     Not connected—No physical connection exists (possibly because the network cable is disconnected or faulty).

 

display reth interface

Use display reth interface to display information about the member interfaces of a Reth interface.

Syntax

display reth interface reth interface-number

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

reth interface-number: Specifies a Reth interface by its number. The value for this argument is 1 or 2.

Examples

# Display information about the member interfaces of Reth 1.

<Sysname> display reth interface reth 1

Reth1 :

  Redundancy group  : aaa

  Member         Physical status       Forwarding status      Presence status

  MGE1/1/0/1      UP                    Active                 Normal

  MGE1/1/0/2      UP                    Inactive               Normal

Table 3 Command output

Field

Description

Redundancy group

The redundancy group to which the Reth interface belongs.

If the Reth interface is not in any redundancy group, this field displays N/A.

Member

Name of the member interface.

Physical status

Physical status of the member interface:

·     Down (redundancy down)—The interface has been shut down by the Reth module.

·     Down—The interface is administratively up but physically down possibly because no physical link is present or the link has failed.

·     UP—The interface is both administratively and physically up.

Forwarding status

Forwarding status of the member interface:

·     Active—The member interface can forward packets.

·     Inactive—The member interface cannot forward packets.

Presence status

Status of the member interface:

·     Normal—The member interface exists.

·     Absent—The member interface does not exist.

 

interface reth

Use interface reth to create a Reth interface and enter its view, or enter the view of an existing Reth interface.

Use undo interface reth to delete a Reth interface.

Syntax

interface reth interface-number

undo interface reth interface-number

Default

No Reth interfaces exist.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

interface-number: Specifies a Reth interface by its number. The value for this argument is 1 or 2.

Usage guidelines

A Reth interface is a virtual Layer 3 interface that uses two member interfaces to ensure link availability.

You cannot delete a Reth interface if it has member interfaces.

Examples

# Create Reth 1 and enter its view.

<Sysname> system-view

[Sysname] interface reth 1

[Sysname-Reth1]

member interface

Use member interface to assign a member interface to a Reth interface.

Use undo member interface to remove a member interface from a Reth interface.

Syntax

member interface interface-type interface-number priority priority

undo member interface interface-type interface-number

Default

A Reth interface does not have member interfaces.

Views

Reth interface view

Predefined user roles

network-admin

mdc-admin

Parameters

interface-type interface-number: Specifies an interface by its type and number. The interface must be a management Ethernet port.

priority: Specifies an interface priority in the range of 1 to 255. The higher the value, the higher the interface priority.

Usage guidelines

You can assign a maximum of two member interfaces to a Reth interface. An interface can belong to only one Reth interface.

As a best practice, assign interfaces of the same type and same speed to a Reth interface.

When the two member interfaces of a Reth interface are up, the system chooses the interface with the higher priority as the active interface to forward packet. The interface with the lower priority is inactive and cannot forward packets.

Do not specify a Reth interface as the outgoing interface in IPv6 static neighbor entries if its member interfaces contain subinterfaces. For more information about IPv6 static neighbor entries, see Layer 3—IP Services Configuration Guide.

Examples

# Assign M-GigabitEthernet 1/0/0/1 and M-GigabitEthernet 1/1/0/2 to Reth 1, and set their priority to 100 and 50, respectively.

<Sysname> system-view

[Sysname] interface reth 1

[Sysname-Reth1] member interface M-GigabitEthernet 1/0/0/1 priority 100

[Sysname-Reth1] member interface M-GigabitEthernet 1/0/0/2 priority 50

mtu

Use mtu to set the MTU of a Reth interface.

Use undo mtu to restore the default.

Syntax

mtu size

undo mtu

Default

The MTU is 1500 bytes for a Reth interface.

Views

Reth interface view

Predefined user roles

network-admin

mdc-admin

Parameters

size: Specifies the MTU in bytes. The value range for this argument is 46 to 1500.

Usage guidelines

The MTU size of a Reth interface affects the fragmentation and reassembly of IP packets on the interface.

For the configured MTU size to take effect, execute the shutdown command, and then the undo shutdown command on the interface.

Examples

# Set the MTU to 200 bytes for Reth 1.

<Sysname> system-view

[Sysname] interface reth 1

[Sysname-Reth1] mtu 200

reset counters interface reth

Use reset counters interface reth to clear statistics for Reth interfaces.

Syntax

reset counters interface [ reth [ interface-number ] ]

Views

User view

Predefined user roles

network-admin

mdc-admin

Parameters

reth [ interface-number ]: Specifies Reth interfaces. The interface-number argument specifies an existing Reth interface by its number. If you do not specify the reth keyword, the command clears statistics for all interfaces. If you specify the reth keyword without the interface-number argument, the command clears statistics for all Reth interfaces.

Usage guidelines

Use this command to clear history statistics before you collect traffic statistics for a time period.

Examples

# Clear statistics for Reth 1.

<Sysname> reset counters interface reth 1

shutdown

Use shutdown to shut down a Reth interface.

Use undo shutdown to bring up a Reth interface.

Syntax

shutdown

undo shutdown

Default

A Reth interface is up.

Views

Reth interface view

Predefined user roles

network-admin

mdc-admin

Examples

# Shut down Reth 1.

<Sysname> system-view

[Sysname] interface reth 1

[Sysname-Reth1] shutdown


Redundancy group commands

The redundancy group feature is supported only in IRF mode.

bind chassis

Use bind chassis to bind a redundancy group node to an IRF member device.

Use undo bind chassis to remove the binding between a redundancy group node and an IRF member device.

Syntax

bind chassis chassis-number

undo bind chassis

Default

A redundancy group node is not bound to an IRF member device.

Views

Redundancy group node view

Predefined user roles

network-admin

mdc-admin

Parameters

chassis-number: Specifies an IRF member device by its member ID.

Usage guidelines

You can create only one-to-one bindings between redundancy group nodes and IRF member devices.

The node in a binding can use interfaces of the bound IRF member device as members. Member interfaces on one node of a redundancy group back up the member interfaces on the other node.

You cannot change the binding for a node if the node has member interfaces.

Examples

# Bind node 1 in redundancy group aaa to IRF member device 3.

<Sysname> system-view

[Sysname] redundancy group aaa

[Sysname-redundancy-group-aaa] node 1

[Sysname-redundancy-group-aaa-node1] bind chassis 3

display redundancy group

Use display redundancy group to display redundancy group information.

Syntax

display redundancy group [ group-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

group-name: Specifies a redundancy group by its name, a case-sensitive string of 1 to 15 characters. If you do not specify a redundancy group, this command displays information about all redundancy groups.

Examples

# Display information about the redundancy group aaa.

<Sysname> display redundancy group aaa

Redundancy group aaa (ID 1):

  Node ID      Chassis        Priority   Status           Track weight

  1            Chassis1       100        Secondary        -255

  2            Chassis2       99         Primary          255

 

Preempt delay time remained   : 0    min

Preempt delay timer setting   : 1    min

Remaining hold-down time      : 0    sec

Hold-down timer setting       : 300  sec

Manual switchover request     : No

 

Member interfaces:

    Reth1          Reth2

Node 1:

  Node member     Physical status

    FGE1/1/0/2     DOWN

    FGE1/1/0/4     DOWN(redundancy down)

  Track info:

    Track    Status       Reduced weight     Interface

    1        Negative     255                FGE1/1/0/2(Fault)

    2        Negative     255                FGE1/1/0/4

Node 2:

  Node member    Physical status

    FGE2/1/0/2    UP

    FGE2/1/0/4    UP

  Track info

    Track    Status       Reduced weight     Interface

    3        Positive     55                 FGE2/1/0/2

    4        Positive     55                 FGE2/1/0/4

Table 4 Command output

Field

Description

Priority

Priority of the node.

Status

Node status:

·     Primary—The primary node. It can forward packets.

·     Secondary—The secondary node. When the high-priority node acts as the secondary node, all its member interfaces are shut down by the Reth module and cannot forward packets. When the low-priority node acts as the secondary node, all its member interfaces can forward packets.

Track weight

Weight of the node.

Preempt delay time remained

Remaining preemption delay time in minutes.

Preempt delay timer setting

Configured preemption delay timer in minutes.

Remaining hold-down time

Remaining hold-down time in seconds.

Hold-down timer setting

Configured hold-down timer in seconds.

Manual switchover request

Manual switchover request:

·     Yes—A request is issued.

·     No—No request is issued.

Member interfaces

Reth interfaces in the redundancy group.

Node 1

Detailed information about the redundancy group node.

Node member

Member interfaces on the redundancy group node.

Physical status

Physical status of the member interfaces on the node:

·     Down (redundancy down)—The interface is shut down by the Reth module.

·     Down—The interface is administratively up but physically down possibly because no physical link is present or the link has failed.

·     UP—The interface is both administratively and physically up.

Track info

Information about the track entries associated with the node.

Track

Track entry number.

Status

Track entry status.

Reduced weight

Weight decrement rate of the node.

Interface

The interface excluded from the shutdown action by the Reth module.

If the interface has failed, this field displays Fault. If the interface is not present, this field displays Absent.

 

hold-down-interval

Use hold-down-interval to set the hold-down timer for a redundancy group.

Use undo hold-down-interval to restore the default.

Syntax

hold-down-interval second

undo hold-down-interval

Default

The hold-down timer is 1 second for a redundancy group.

Views

Redundancy group view

Predefined user roles

network-admin

mdc-admin

Parameters

second: Specifies the hold-down timer in the range of 0 to 1800 seconds.

Usage guidelines

Set the hold-down timer to prevent frequent switchovers. The hold-down timer specifies the minimum interval between two switchovers. This timer starts when a switchover is finished. The redundancy group can perform another switchover only after the hold-down timer expires.

Examples

# Set the hold-down timer to 300 seconds for redundancy group aaa.

<Sysname> system-view

[Sysname] redundancy group aaa

[Sysname-redundancy-group-aaa] hold-down-interval 300

member interface

Use member interface to assign a Reth interface to a redundancy group.

Use undo member interface to remove a Reth interface from a redundancy group.

Syntax

member interface reth interface-number

undo member interface reth interface-number

Default

A redundancy group does not contain Reth interfaces.

Views

Redundancy group view

Predefined user roles

network-admin

mdc-admin

Parameters

reth interface-number: Specifies an existing Reth interface by its number. The value for this argument is 1 or 2.

Usage guidelines

You can assign a Reth interface to only one redundancy group.

A redundancy group can contain a maximum of 32 Reth interfaces.

Examples

# Assign Reth 1 to redundancy group aaa.

<Sysname> system-view

[Sysname] redundancy group aaa

[Sysname-redundancy-group-aaa] member interface reth 1

node

Use node to create a redundancy group node and enter its view, or enter the view of an existing redundancy group node.

Use undo node to remove a redundancy group node.

Syntax

node node-id

undo node node-id

Default

No redundancy group nodes exist.

Views

Redundancy group view

Predefined user roles

network-admin

mdc-admin

Parameters

node-id: Specifies a redundancy group node ID in the range of 1 to 2.

Usage guidelines

You can create a maximum of two nodes for a redundancy group. One is the primary node, and the other is the secondary node.

Before you delete a redundancy group node, you must remove the binding between the node and its IRF member device.

Examples

# Create node 1 for redundancy group aaa.

<Sysname> system-view

[Sysname] redundancy group aaa

[Sysname-redundancy-group-aaa] node 1

Related commands

bind chassis

node-member interface

Use node-member interface to assign a physical Ethernet interface to a redundancy group node.

Use undo node-member interface to remove a physical Ethernet interface from a redundancy group node.

Syntax

node-member interface interface-type interface-number

undo node-member interface interface-type interface-number

Default

A redundancy group node does not have member interfaces.

Views

Redundancy group node view

Predefined user roles

network-admin

mdc-admin

Parameters

interface-type interface-number: Specifies a physical interface by its type and number. The interface must belong to the IRF member device that is bound to the node.

Usage guidelines

Before you assign physical Ethernet interfaces to a redundancy group node, you must use the bind chassis command to bind the node to an IRF member device.

The physical Ethernet interfaces cannot be members of Reth interfaces.

An interface can be assigned to only one redundancy group node.

Examples

# Assign FortyGigE 1/1/0/1 to node 1 of redundancy group aaa.

<Sysname> system-view

[Sysname] redundancy group aaa

[Sysname-redundancy-group-aaa] node 1

[Sysname-redundancy-group-aaa-node1]node-member interface fortygige 1/1/0/1

Related commands

bind chassis

preempt-delay

Use preempt-delay to set the preemption delay timer for a redundancy group.

Use undo preempt-delay to restore the default.

Syntax

preempt-delay min

undo preempt-delay

Default

The preemption delay timer is 1 minute for a redundancy group.

Views

Redundancy group view

Predefined user roles

network-admin

mdc-admin

Parameters

min: Specifies the preemption delay timer in the range of 0 to 12 minutes. If you set this timer to 0 seconds, manual and automatic switchovers to the high-priority node are disabled.

Usage guidelines

The preemption delay timer specifies the delay before a switchover to the high-priority node occurs after the switchover is triggered. The delay allows the system to process events (such as interface state changes) required for the switchover.

Examples

# Set the preemption delay timer to 2 minutes for redundancy group aaa.

<Sysname> system-view

[Sysname] redundancy group aaa

[Sysname-redundancy-group-aaa] preempt-delay 2

priority

Use priority to set the priority of a redundancy group node.

Use undo priority to restore the default.

Syntax

priority priority

undo priority

Default

The priority of a redundancy group node is 1.

Views

Redundancy group node view

Predefined user roles

network-admin

mdc-admin

Parameters

priority: Specifies the priority in the range of 1 to 255. The higher the value, the higher the priority.

Usage guidelines

By default, the high-priority node is the primary node, and the low-priority node is the secondary node. If both nodes have the same priority, the lower-numbered node is the primary node.

Examples

# Set the priority to 3 for node 1 of redundancy group aaa.

<Sysname> system-view

[Sysname] redundancy group aaa

[Sysname-redundancy-group-aaa] node 1

[Sysname-redundancy-group-aaa-node1] priority 3

redundancy group

Use redundancy group to create a redundancy group and enter its view, or enter the view of an existing redundancy group.

Use undo redundancy group to remove a redundancy group.

Syntax

redundancy group group-name

undo redundancy group group-name

Default

No redundancy groups exist.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

group-name: Specifies a redundancy group name, a case-sensitive string of 1 to 15 characters.

Usage guidelines

You can create a maximum of 255 redundancy groups.

Before you delete a redundancy group, make sure all its Reth interfaces and nodes, are removed.

Examples

# Create redundancy group aaa and enter its view.

<Sysname> system-view

[Sysname] redundancy group aaa

snmp-agent trap enable rddc

Use snmp-agent trap enable rddc to enable SNMP notifications for redundancy groups.

Use undo snmp-agent trap enable rddc to disable SNMP notifications for redundancy groups.

Syntax

snmp-agent trap enable rddc

undo snmp-agent trap enable rddc

Default

SNMP notifications are enabled for redundancy groups.

Views

System view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

This command enables SNMP notifications for the following events:

·     A manual switchover is performed.

·     An interface goes down.

·     A faulty interface is recovered.

For redundancy group event notifications to be sent correctly, you must also configure SNMP on the device. For more information about SNMP configuration, see the network management and monitoring configuration guide for the device.

Examples

# Enable SNMP notifications for redundancy groups.

<Sysname> system-view

[Sysname] snmp-agent trap enable rddc

switchover request

Use switchover request to request a switchover to the low-priority node.

Syntax

switchover request

Views

Redundancy group view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

Use this command to request a switchover to the low-priority node when both of the redundancy group nodes are operating correctly. This command can be used in scenarios where component replacement is required for the high-priority node.

Examples

# Request a switchover to the low-priority node for redundancy group aaa.

<Sysname> system-view

[Sysname] redundancy group aaa

[Sysname-redundancy-group-aaa] switchover request

Related commands

switchover reset

switchover reset

Use switchover reset to request a switchover to the high-priority node.

Syntax

switchover reset

Views

Redundancy group view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

Use this command to request a switchover to the high-priority node when both of the redundancy group nodes are operating correctly.

Examples

# Request a switchover to the high-priority node for redundancy group aaa.

<Sysname> system-view

[Sysname] redundancy group aaa

[Sysname-redundancy-group-aaa] switchover reset

Related commands

switchover request

track

Use track to associate a track entry with a redundancy group node.

Use undo track to remove the association between a track entry and a redundancy group node.

Syntax

track track-entry-number [ reduced weight-reduced ] [ interface interface-type interface-number ]

undo track track-entry-number

Default

A redundancy group node is not associated with track entries.

Views

Redundancy group node view

Predefined user roles

network-admin

mdc-admin

Parameters

track-entry-number: Specifies a track entry by its number in the range of 1 to 1024.

reduced weight-reduced: Specifies the weight decrement rate in the range of 1 to 255. The default is 255.

interface interface-type interface-number: Specifies an interface by its type and number. The interface will be excluded from the shutdown action by the Reth module. If you do not specify this option, no interface is excluded from the shutdown action by the Reth module. You must specify the tracked interface for this option if the interface has one of the following roles:

·     Member of the redundancy group.

·     Member of a Reth interface in the redundancy group.

Usage guidelines

You can associate a maximum of 64 track entries with a redundancy group node.

As a best practice, associate a redundancy group node with an existing track entry. If the track entry does not exist, a switchover might occur.

Do not exclude a subinterface from the shutdown action if both the subinterface and its main interface have one of the following roles on the high-priority node:

·     Member of the redundancy group.

·     Member of a Reth interface in the redundancy group.

When the Reth module shuts down the main interface, the subinterface is also shut down. The shutdown subinterface cannot recover automatically to trigger an automatic switchover.

Examples

# Associate track entries 1 and 2 with redundancy group node 1. Exclude FortyGigE 1/1/0/1 and FortyGigE 2/1/0/1 from the shutdown action by the Reth module.

<Sysname> system-view

[Sysname] track 1 interface fortygige 1/1/0/1

[Sysname] track 2 interface fortygige 2/1/0/1

[Sysname] redundancy group aaa

[Sysname-redundancy-group-aaa] node 1

[Sysname-redundancy-group-aaa-node1] track 1 reduced 50 interface fortygige 1/1/0/1

[Sysname-redundancy-group-aaa-node1] track 2 reduced 50 interface fortygige 2/1/0/1

  • Cloud & AI
  • InterConnect
  • Intelligent Computing
  • Security
  • SMB Products
  • Intelligent Terminal Products
  • Product Support Services
  • Technical Service Solutions
All Services
  • Resource Center
  • Policy
  • Online Help
All Support
  • Become a Partner
  • Partner Resources
  • Partner Business Management
All Partners
  • Profile
  • News & Events
  • Online Exhibition Center
  • Contact Us
All About Us
新华三官网