11-Network Management and Monitoring Command Reference

HomeSupportResource CenterSwitchesS12500X-AF SeriesS12500X-AF SeriesTechnical DocumentsReference GuidesCommand ReferencesH3C S12500X-AF Switch Series Command References(R28xx)-6W10011-Network Management and Monitoring Command Reference
04-PTP commands
Title Size Download
04-PTP commands 177.30 KB

PTP commands

Only the default MDC supports PTP. Non-default MDCs do not support PTP or PTP commands. For more information about MDCs, see Virtual Technologies Configuration Guide.

display ptp clock

Use display ptp clock to display PTP clock information.

Syntax

display ptp clock

Views

Any view

Predefined user roles

network-admin

network-operator

Usage guidelines

This command does not display any information if you have not specified a PTP profile (PTP standard) or a PTP mode.

Examples

# Display PTP clock information.

<Sysname> display ptp clock

PTP profile         : IEEE 1588 Version 2

PTP mode            : BC

Slave only          : No

Clock ID            : 000FE2-FFFE-FF0000

Clock type          : ToD1

 ToD direction  : In

 ToD delay time : 0 (ns)

Clock type          : ToD1

 ToD direction  : In

 ToD delay time : 0 (ns)

Clock domain        : 0

Number of PTP ports : 2

Priority1     : 128

Priority2     : 128

Clock quality :

 Class                 : 248

 Accuracy              : 254

 Offset (log variance) : 65535

Offset from master : -4 (ns)

Mean path delay    : 101 (ns)

Steps removed      : 1

Local clock time   : Sun Jan 15 20:57:29 2011

Table 1 Command output

Field

Description

PTP profile

PTP standard:

·     IEEE 1588 version 2.

·     IEEE 802.1AS.

·     SMPTE ST 2059-2.

PTP mode

Clock node type:

·     BC.

·     E2ETC.

·     E2ETC-OC.

·     OC.

·     P2PTC.

·     P2PTC-OC.

Slave only

Whether the OC operates in Slave only mode:

·     Yes.

·     No.

Clock ID

Clock ID for the device, which uniquely identifies a PTP device.

Clock type

Clock type of the device:

Local—Local clock.

Clock domain

PTP domain where the device resides.

Priority1

Priority 1 value for the device.

Priority2

Priority 2 value for the device.

Class

Time class of the device.

Accuracy

Time accuracy of the device.

Offset (log variance)

Offset of the grandmaster clock.

Offset from master

Offset from the master clock node (parent clock node), in nanoseconds.

N/A indicates that information for this field is not obtained.

Mean path delay

Mean path delay, in nanoseconds.

N/A indicates that information for this field is not obtained.

Steps removed

Hops from the grandmaster to the local clock node.

N/A indicates that information for this field is not obtained.

display ptp corrections

Use display ptp corrections to display PTP corrections that have occurred on a subordinate port.

Syntax

display ptp corrections

Views

Any view

Predefined user roles

network-admin

network-operator

Usage guidelines

The PTP corrections are displayed only when the following conditions are met:

·     You have specified a PTP profile and PTP mode for the device.

·     The device has a subordinate port and has performed time or frequency synchronization through the port.

If the subordinate port is changed, the recorded information will be cleared.

Examples

# Display PTP corrections that have occurred on a subordinate port.

<Sysname> display ptp corrections

Slave port   Correction time          Corrections(s,ns)     Rate ratio

FGE1/0/1     Mar 11 03:14:54 2012     0,74                  0.999999973

FGE1/0/1     Mar 11 03:14:55 2012    -1,17                  0.999999980

Table 2 Command output

Field

Description

Slave port

Name of the subordinate port.

Correction time

Time when the correction occurred.

Corrections(s,ns)

Time corrections in seconds or nanoseconds.

N/A indicates that no correction occurred this time.

Rate ratio

Ratio of the subordinate port rate to the master port rate.

N/A indicates that no correction occurred this time.

display ptp foreign-masters-record

Use display ptp foreign-masters-record to display information about foreign master nodes.

Syntax

display ptp foreign-masters-record [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays information about foreign master nodes for all interfaces.

Usage guidelines

Foreign master node information is displayed only when the following conditions are met:

·     You have specified the IEEE 1588 version 2 or SMPTE ST 2059-2 PTP profile.

·     You have specified a PTP mode for the device.

·     The device has a port in slave, passive, or uncalibrated state.

Examples

# Display information about foreign master nodes for all interfaces.

<Sysname> display ptp foreign-masters-record

P1=Priority1, P2=Priority2, C=Class, A=Accuracy,

OSLV=Offset-scaled-log-variance, SR=Steps-removed

GM=Grandmaster

--------- ----------------------- ---- ---- ---- ---- ----- ---------

Interface    Clock ID             P1   P2   C    A    OSLV   SR   GM

--------- ----------------------- ---- ---- ---- ---- ----- ---------

FGE1/0/1     000FE2-FFFE-FF0000   0    128  248  254  65535  0    Yes

FGE1/0/2     000FE2-FFFE-FF0001   0    128  248  254  65535  1    No

Table 3 Command output

Field

Description

Interface

Name of a PTP interface.

Clock ID

Clock ID of the foreign master node.

C

Time class.

A

Time accuracy.

OSLV

Offset of the grandmaster clock.

SR

Hops from the grandmaster to the local clock node.

GM

Whether the node represents the grandmaster clock:

·     Yes.

·     No.

display ptp interface

Use display ptp interface to display PTP running information for an interface.

Syntax

display ptp interface [ interface-type interface-number | brief ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays PTP running information for all interfaces.

brief: Displays brief PTP running information for all interfaces. If you do not specify this keyword, this command displays detailed PTP running information for the specified interface or all interfaces.

Usage guidelines

The detailed PTP running information can be displayed only if you enable PTP on the interface. The brief PTP running information can be displayed only when PTP is operating on the interface.

Examples

# Display brief PTP running information for all interfaces.

<Sysname> display ptp interface brief

Name         State        Delay mechanism  Clock step  Asymmetry correction

FGE1/0/1     Slave        E2E              Two         0

FGE1/0/2     Passive      E2E              Two         0

# Display detailed PTP running information for FortyGigE 1/0/1.

<Sysname> display ptp interface fortygige 1/0/1

Clock ID                    : 000FE2-FFFE-FF0000

Port number                 : 15

PTP version                 : 2

PTP enable                  : Enabled

Transport of PTP            : User Datagram Protocol (IPv4)

Unicast destination address : 10.10.10.2

DSCP priority               : 56

Port state                  : Slave

Force state                 : No

Clock step                  : Two

Asymmetry correction        : 0

Delay mechanism             : End to End

Announce interval (log mean)           : 1

Announce receipt time out              : 3

Sync interval (log mean)               : 2

Delay request interval (log mean)      : 2

Peer delay request interval (log mean) : 0

Mean path delay                        : 0 (ns)

Table 4 Command output

Field

Description

Name

Name of the PTP interface.

State

States of the PTP interface:

·     Slave—Receives synchronization messages.

·     Uncalibrated—Temporary state before the interface enters Slave state.

·     Passive—Neither receives nor sends synchronization messages. A PTP interface is in passive state after it receives an announce messages.

·     Master—Sends synchronization messages.

·     Premaster—Temporary state before the interface enters Master state.

·     Listening—Neither receives nor sends synchronization messages. A PTP interface is in listening state after being initialized.

·     Faulty—PTP is running incorrectly. A PTP interface in faulty state does not process PTP messages.

·     Disabled—PTP is not running on the interface. A PTP interface in disabled state does not process PTP messages.

·     Initializing—The interface is initializing. A PTP interface in initializing state does not process PTP messages.

·     N/A—No PTP interface state is obtained.

Delay mechanism

Delay measurement mechanism:

·     End to End—Request-response mechanism.

·     Peer to Peer—Peer delay mechanism.

Clock step

Mode for carrying timestamps:

·     One—Single-step mode. This field is not supported in the current software version.

·     Two—Two-step mode.

Asymmetry correction

Asymmetric delay correction value (in nanoseconds).

Clock ID

Clock ID of the device where the interface resides.

PTP version

PTP version number. The version number is always 2.

PTP enable

Whether PTP is enabled or disabled:

·     Enabled.

·     Disabled.

Transport of PTP

PTP message transport protocol:

·     User Datagram Protocol (IPv4).

·     IEEE 802.3/Ethernet.

Unicast destination address

Destination IP address for unicast PTP messages that are transmitted over IPv4 UDP. This field is not displayed if the ptp unicast-destination command is not executed.

DSCP priority

DSCP value for PTP messages that are transmitted over IPv4 UDP. This field is not displayed if the ptp dscp command is not executed.

VLAN

VLAN ID for PTP messages. This field is not displayed if the ptp vlan command is not executed.

Dot1p priority

802.1p precedence for PTP messages. This field is not displayed if the ptp vlan command is not executed.

Force state

Whether the force state is configured:

·     Yes.

·     No.

Announce interval (log mean)

Announce message sending interval (in seconds) = 2interna. This field displays the value for the interval exponent.

Announce receipt time out

Number of announcement intervals before the receiving node stops receiving announce messages. If a member node does not receive any announce message from the master node within the specified value, it considers the master node invalid.

Sync interval (log mean)

Sync message sending interval (in seconds) = 2interval. This field displays the value for the interval exponent.

Delay request interval (log mean)

Minimum delay request message sending interval (in seconds) = 2interval. This field displays the value for the interval exponent.

Peer delay request interval (log mean)

Peer delay request message sending interval (in seconds) = 2interval. This field displays the value for the interval exponent.

Mean path delay

Mean path delay, in nanoseconds.

display ptp parent

Use display ptp parent to display parent node (master node) information for the PTP device.

Syntax

display ptp parent

Views

Any view

Predefined user roles

network-admin

network-operator

Usage guidelines

The command does not display any information in any of the following circumstances:

·     You have not specified a PTP profile or a PTP mode for the device.

·     You have specified the TC clock node type.

·     You have executed the ptp active force-state command.

Examples

# Display parent node information for the PTP device.

<Sysname> display ptp parent

Parent clock:

 Parent clock ID                         : 000FE2-FFFE-FF0005

 Parent port number                      : 15

 Observed parent offset (log variance)   : N/A

 Observed parent clock phase change rate : N/A

Grandmaster clock:

 Grandmaster clock ID: 000FE2-FFFE-FF0000

 Grandmaster clock quality:

  Class                 : 248

  Accuracy              : 254

  Offset (log variance) : 65535

  Priority1             : 128

  Priority2             : 128

Table 5 Command output

Field

Description

Parent port number

Outgoing interface number of the parent clock.

Observed parent offset (log variance)

Offset from the parent clock node.

N/A indicates that information for this field is not obtained.

Class

Time class of the grandmaster clock.

Accuracy

Time accuracy of the grandmaster clock.

Offset (log variance)

Offset of the grandmaster clock.

Priority1

Priority 1 value of the grandmaster clock.

Priority2

Priority 2 value of the grandmaster clock.

display ptp statistics

Use display ptp statistics to display PTP statistics.

Syntax

display ptp statistics [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays PTP statistics for all interfaces.

Usage guidelines

The command does not display any PTP statistics if you have not specified a PTP profile or a PTP mode.

Examples

# Display PTP statistics on FortyGigE 1/0/1.

<Sysname> display ptp statistics interface fortygige 1/0/1

                     Received packets

--------------------------------------------------------------------------

Announce :0          Sync      :0          Signaling          :0

DelayReq :0          DelayResp :0          FollowUp           :0

PdelayReq:0          PdelayResp:0          PdelayRespFollowUp :0

 

                     Sent packets

--------------------------------------------------------------------------

Announce :476        Sync      :2543       Signaling          :0

DelayReq :0          DelayResp :0          FollowUp           :2542

PdelayReq:238        PdelayResp:0          PdelayRespFollowUp :0

 

                     Discarded packets

--------------------------------------------------------------------------

Announce :0          Sync      :0          Signaling          :0

DelayReq :0          DelayResp :0          FollowUp           :0

PdelayReq:0          PdelayResp:0          PdelayRespFollowUp :0

Table 6 Command output

Field

Description

Received packets

Statistics about received PTP messages.

Sent packets

Statistics about sent PTP messages.

Discarded packets

Statistics about discarded PTP messages.

display ptp time-property

Use display ptp time-property to display PTP clock properties.

Syntax

display ptp time-property

Views

Any view

Predefined user roles

network-admin

network-operator

Usage guidelines

This command does not display any information in any of the following circumstances:

·     You have not specified a PTP profile or a clock node type.

·     You have specified the e2etc or p2ptc clock node type.

·     You have executed the ptp active force-state command.

Examples

# Display PTP clock properties.

<Sysname> display ptp time-property

PTP clock time property:

 Current UTC offset valid : True

 Current UTC offset       : 33

 Leap59 : Yes

 Leap61 : No

 Time traceable      : True

 Frequency traceable : True

 PTP timescale       : True

 Time source         : 0xA0 (Internal oscillator)

Table 7 Command output

Field

Description

Current UTC offset valid

Whether the Coordinated Universal Time (UTC) offset is valid:

·     True—Yes.

·     False—No.

Current UTC offset

Cumulative offset (in seconds) between the UTC of the grandmaster clock and the International Atomic Time (TAI).

Leap59

Whether cumulative offset is minus 1:

·     Yes.

·     No.

Leap61

Whether cumulative offset is plus 1:

·     Yes.

·     No.

Time traceable

Whether the PTP time is traceable:

·     True—Yes.

·     False—No.

Frequency traceable

Whether the PTP frequency is traceable:

·     True—Yes.

·     False—No.

PTP timescale

The possible timescales available for use by the grandmaster clock:

·     True—PTP timescale.

·     False—Non-PTP timescale.

Time source

Attributes of the grandmaster clock:

·     Atomic clock.

·     GPS.

·     Handset.

·     Internal oscillator.

·     NTP.

·     Other.

·     PTP.

·     Terrestrial radio.

·     Unknown.

ptp active force-state

Use ptp active force-state to activate the port role configuration.

Use undo ptp active force-state to restore the default.

Syntax

ptp active force-state

undo ptp active force-state

Default

The port role configuration is not activated.

Views

System view

Predefined user roles

network-admin

Usage guidelines

This command is available only after you specify a PTP profile and a PTP mode.

Examples

# Activate the port role configuration.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] ptp active force-state

Related commands

ptp force-state

ptp mode

ptp profile

ptp announce-interval

Use ptp announce-interval to set the interval for sending announce messages.

Use undo ptp announce-interval to restore the default.

Syntax

ptp announce-interval interval

undo ptp announce-interval

Default

For the IEEE 1588 version 2 PTP profile, the interval argument value is 1 and the announce message sending interval is 2 (21) seconds.

For the IEEE 802.1AS PTP profile, the interval argument value is 0 and the announce message sending interval is 1 (20) second.

For the SMPTE ST 2059-2 PTP profile, the interval argument value is –2 and the announce message sending interval is 1/4 (2-2) second.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

interval: Specifies an exponent, to the power of which base 2 is raised to get the interval in seconds for sending announce messages. When the PTP profile is IEEE 1588 version 2, the value range for the interval argument is 0 to 4. When the PTP profile is IEEE 802.1AS, the value range for the interval argument is 0 to 6. When the PTP profile is SMPTE ST 2059-2, the value range for the interval argument is –3 to 1.

Usage guidelines

This command is available only after you specify a PTP profile and a PTP mode.

The master node uses the value configured on its interface as the interval for sending announce messages.

Examples

# Set the announce message sending interval to 4 (22) seconds on FortyGigE 1/0/1.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp announce-interval 2

Related commands

ptp mode

ptp profile

ptp announce-timeout

Use ptp announce-timeout to set the timeout multiplier for the announce message receiving interval.

Use undo ptp announce-timeout to restore the default.

Syntax

ptp announce-timeout multiple-value

undo ptp announce-timeout

Default

The timeout multiplier for the announce message receiving interval is 3.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

multiple-value: Sets the timeout multiplier for the announce message receiving interval, in the range of 2 to 10.

Usage guidelines

A master node periodically sends announce messages to the member nodes.

·     IEEE 1588 version 2 or SMPTE ST 2059-2—If a member node does not receive any announce message from the master node within multiple-value times the announce message sending interval, it determines that the master node is invalid.

·     IEEE 802.1AS—If a member node does not receive any announce message from the master node within multiple-value times the announce message sending interval configured on the master node, it determines that the master node is invalid.

This command is available only after you specify a PTP profile and a PTP mode.

To ensure a stable PTP network, set the timeout multiplier for receiving announce messages to a value in the range of 5 to 7.

Examples

# Set the timeout multiplier for the announce message sending interval to 5 on FortyGigE 1/0/1.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp announce-timeout 5

Related commands

ptp announce-interval

ptp mode

ptp profile

ptp asymmetry-correction

Use ptp asymmetry-correction to set the asymmetric delay correction time.

Use undo ptp asymmetry-correction to restore the default.

Syntax

ptp asymmetry-correction { minus | plus } value

undo ptp asymmetry-correction

Default

The asymmetric delay correction time is 0 nanoseconds, which means that delay correction is not performed.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

minus: Subtracts the specified asymmetric delay correction value.

plus: Adds the specified asymmetric delay correction value.

value: Specifies the asymmetric delay correction value in the range of 0 to 2000000 nanoseconds.

Usage guidelines

This command is available only after you specify a PTP profile and a PTP mode.

Examples

# Set the asymmetric delay correction time to 100 nanoseconds on FortyGigE 1/0/1.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp asymmetry-correction plus 100

Related commands

ptp mode

ptp profile

ptp delay-mechanism

Use ptp delay-mechanism to specify a delay measurement mechanism for a BC or an OC.

Use undo ptp delay-mechanism to restore the default.

Syntax

ptp delay-mechanism { e2e | p2p }

undo ptp delay-mechanism

Default

The default setting varies by PTP profile:

·     IEEE 1588 version 2 or SMPTE ST 2059-2 PTP profile—The request-response delay measurement applies.

·     IEEE 802.1AS PTP profile—The peer delay measurement mechanism applies.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

e2e: Specifies the request-response mechanism.

p2p: Specifies the peer delay mechanism.

Usage guidelines

You can configure this command only after you have specified a PTP profile and PTP mode for the device. Follow these restrictions and guidelines when you configure this command:

·     IEEE 1588 version 2 or SMPTE ST 2059-2 PTP profile:

¡     You can configure this command only for a BC or OC clock node.

¡     The E2ETC, E2ETC+OC, P2PTC, and P2PTC+OC clock nodes do not support this command. The E2ETC and E2ETC+OC clock nodes support both the request-response and peer delay measurement mechanisms. The P2PTC clock node supports only the peer delay measurement mechanism.

·     IEEE 802.1AS PTP profile: Supports only the peer delay measurement mechanism and does not support this command.

Examples

# Specify the OC clock node type. Specify the request-response delay measurement mechanism (e2e) on FortyGigE 1/0/1.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp delay-mechanism e2e

Related commands

ptp mode

ptp profile

ptp destination-mac

Use ptp destination-mac to configure the destination MAC address for non-peer delay messages.

Use undo ptp destination-mac to restore the default.

Syntax

ptp destination-mac mac-address

undo ptp destination-mac

Default

The destination MAC address for non-peer delay messages is 011B-1900-0000.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

mac-address: Specifies the destination MAC address for non-peer delay messages as 0180-C200-000E or 011B-1900-0000.

Usage guidelines

This command is available only after you specify IEEE 1588 version 2 or SMPTE ST 2059-2 as the PTP profile and specify a PTP mode.

Peer delay messages include Pdelay_Req, Pdelay_Resp, and Pdelay_Resp_Follow_Up messages. The destination MAC address for peer delay messages is 0180-C200-000E, which cannot be modified.

This command takes effect only if PTP messages are encapsulated in IEEE 802.3/Ethernet packets.

Examples

# Configure the destination MAC address for non-peer delay messages as 0180-C200-000E on FortyGigE 1/0/1.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp destination-mac 0180-c200-000e

Related commands

ptp mode

ptp profile

ptp domain

Use ptp domain to specify a PTP domain.

Use undo ptp domain to restore the default.

Syntax

ptp domain domain-number

undo ptp domain

Default

When the PTP profile is IEEE 1588 version 2 or IEEE 802.1AS, the device is in PTP domain 0.

When the PTP profile is SMPTE ST 2059-2, the device is in PTP domain 127.

Views

System view

Predefined user roles

network-admin

Parameters

domain-number: Specifies a PTP domain by its number. When the PTP profile is IEEE 1588 version 2 or IEEE 802.1AS, the value range for the domain-number argument is 0 to 255. When the PTP profile is SMPTE ST 2059-2, the value range for the domain-number argument is 0 to 127.

Usage guidelines

This command is available only after you specify a PTP profile and a PTP mode.

Examples

# Configure the PTP domain number to use for the device as 2.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] ptp domain 2

Related commands

ptp mode

ptp profile

ptp dscp

Use ptp dscp to set a DSCP value for PTP messages that are transmitted over IPv4 UDP.

Use undo ptp dscp to restore the default.

Syntax

ptp dscp dscp

undo ptp dscp

Default

The DSCP value is 56 for PTP messages that are transmitted over IPv4 UDP.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

dscp: Sets a DSCP value in the range of 0 to 63 for PTP messages.

Usage guidelines

This command is available only after you specify a PTP profile and a PTP mode.

The IEEE 802.1AS PTP profile does not support this command.

This command takes effect only if PTP messages are transmitted over IPv4 UDP.

Examples

# Set the DSCP value to 63 for PTP messages transmitted over IPv4 UDP on FortyGigE 1/0/1.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp transport-protocol udp

[Sysname-FortyGigE1/0/1] ptp dscp 63

Related commands

ptp mode

ptp profile

ptp transport-protocol

ptp enable

Use ptp enable to enable PTP.

Use undo ptp enable to disable PTP.

Syntax

ptp enable

undo ptp enable

Default

PTP is disabled.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

This command is available only after you specify a PTP profile and a PTP mode.

You can enable PTP on only one port if the clock node type of the device is OC.

As a best practice, enable PTP on an interface after you configure PTP parameters.

To enable PTP on a Layer 3 Ethernet interface that has been assigned to a VPN instance, you must specify this VPN instance in the ptp source ip-address vpn-instance vpn-instance-name command if PTP messages are to be transmitted in multicast mode over IPv4 UDP.

Examples

# Configure the clock node type as OC, and enable PTP on FortyGigE 1/0/1.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp enable

# Configure the clock node type as E2ETC, and enable PTP on FortyGigE 1/0/1 and FortyGigE 1/0/2.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode e2etc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp enable

[Sysname-FortyGigE1/0/1] interface fortygige 1/0/2

[Sysname-FortyGigE1/0/2] ptp enable

Related commands

ptp mode

ptp profile

ptp source

ptp force-state

Use ptp force-state to configure a role for a PTP port.

Use undo ptp force-state to restore the default.

Syntax

ptp force-state { master | passive | slave }

undo ptp force-state

Default

The PTP port role is automatically calculated by BMC.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

master: Specifies the PTP port as a master port.

passive: Specifies the PTP port as a passive port.

slave: Specifies the PTP port as a subordinate port.

Usage guidelines

By default, the PTP port roles are automatically negotiated based on the BMC algorithm. If you use this command to change the role of one PTP port, all the other PTP ports in the PTP domain stop working. For these PTP ports to function, you must specify roles for each of them by using this command. As a best practice, enable automatic negotiation of PTP port roles based on the BMC algorithm.

This command is available only after you specify a PTP profile and a PTP mode.

You can configure only one subordinate port for a device.

Examples

# Configure the clock node type as OC. Specify the PTP port FortyGigE 1/0/1 as a subordinate port.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp force-state slave

Related commands

ptp active force-state

ptp mode

ptp profile

ptp slave-only

ptp min-delayreq-interval

Use ptp min-delayreq-interval to set the minimum interval for sending delay request messages.

Use undo ptp min-delayreq-interval to restore the default.

Syntax

ptp min-delayreq-interval interval

undo ptp min-delayreq-interval

Default

When the PTP profile is IEEE 1588 version 2 or SMPTE ST 2059-2, the minimum interval for sending delay request messages is 1 (20) second.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

interval: Specifies an exponent, to the power of which base 2 is raised to get the interval in seconds for sending delay request messages. When the PTP profile is IEEE 1588 version 2, the value range for the interval argument is –4 to 6. When the PTP profile is SMPTE ST 2059-2, the value range for the interval argument is –5 to 4.

Usage guidelines

When a member clock receives a Sync message, it responds by sending a Delay_Req message and starts a timer defined by this command. The member clock will not send another Delay_Req message until it receives a Sync message after the timer expires.

This command is available only after you specify a PTP profile and a PTP mode.

The IEEE 802.1AS PTP profile does not support this command.

In PTP multicast transport mode, this command takes effect only when configured on the master clock. The master clock sends the value to a member clock through PTP messages to control the interval for the member clock to send Delay_Req messages. To view the interval, execute the display ptp interface command on the member clock.

In PTP unicast transport mode, this command takes effect when configured on member clocks. It does not take effect when configured on the master clock.

When the PTP profile is SMPTE ST 2059-2, set the interval argument to a value in the range of ptp syn-interval interval to ptp syn-interval interval plus 5 as a best practice.

Examples

# Set the minimum interval to 4 (22) seconds for sending delay request messages on FortyGigE 1/0/1.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp min-delayreq-interval 2

Related commands

ptp mode

ptp profile

ptp syn-interval

ptp mode

Use ptp mode to specify a clock node type for the device.

Use undo ptp mode to restore the default.

Syntax

IEEE 1588v2 PTP profile:

ptp mode { bc | e2etc | e2etc-oc | oc | p2ptc | p2ptc-oc }

undo ptp mode

IEEE 802.1AS PTP profile:

ptp mode { bc | oc | p2ptc | p2ptc-oc }

undo ptp mode

SMPTE ST 2059-2 PTP profile:

ptp mode { bc | e2etc | oc | p2ptc }

undo ptp mode

Default

No clock node type is specified.

Views

System view

Predefined user roles

network-admin

Parameters

bc: Specifies the boundary clock (BC) type.

e2etc: Specifies the end-to-end transparent clock (E2ETC) type.

e2etc-oc: Specifies the E2ETC+OC type.

oc: Specifies the ordinary clock (OC) type.

p2ptc: Specifies the peer-to-peer transparent clock (P2PTC) type.

p2ptc-oc: Specifies the P2PTC+OC type.

Usage guidelines

CAUTION

CAUTION:

If you change the clock node type for the device, all settings except for the PTP profile will be removed.

This command is available only after you specify a PTP profile.

When the PTP profile is IEEE 802.1AS, you cannot specify the E2ETC or E2ETC+OC clock node type.

When the PTP profile is SMPTE ST 2059-2, you cannot specify the E2ETC+OC or P2PTC+OC clock node type.

Examples

# Specify the OC clock node type for the device.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

Related commands

ptp profile

ptp pdelay-req-interval

Use ptp pdelay-req-interval to set the interval for sending peer delay request messages.

Use undo ptp pdelay-req-interval to restore the default.

Syntax

ptp pdelay-req-interval interval

undo ptp pdelay-req-interval

Default

The interval for sending peer delay request messages is 1 (20) second.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

interval: Specifies an exponent, to the power of which base 2 is raised to get the interval in seconds for sending peer delay request messages. When the PTP profile is IEEE 1588 version 2, the value range for the interval argument is 0 to 5. When the PTP profile is IEEE 802.1AS, the value range for the interval argument is –4 to 6. When the PTP profile is SMPTE ST 2059-2, the value range for the interval argument is –5 to 4.

Usage guidelines

This command is available only after you specify a PTP profile and a PTP mode.

When the PTP profile is SMPTE ST 2059-2, set the interval argument to a value in the range of ptp syn-interval interval to ptp syn-interval interval plus 5 as a best practice.

Examples

# Set the interval to 4 (22) seconds for sending peer delay request messages on FortyGigE 1/0/1.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp pdelay-req-interval 2

Related commands

ptp mode

ptp profile

ptp syn-interval

ptp port-mode

Use ptp port-mode to configure the port type as OC for a TC+OC (including E2ETC+OC and P2PTC+OC) clock.

Use undo ptp port-mode to restore the default.

Syntax

ptp port-mode oc

undo ptp port-mode

Default

The type of all ports on an E2ETC+OC or a P2PTC+OC clock is TC.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

oc: Specifies the port type for a TC+OC clock as OC.

Usage guidelines

This command is applicable only to E2ETC+OC and P2PTC+OC clocks and is available only after you specify a PTP profile and a PTP mode.

The SMPTE ST 2059-2 PTP profile does not support this command.

Examples

# Specify the P2PTC+OC clock node type for the device. Specify the OC port type for FortyGigE 1/0/1.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode p2ptc-oc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp port-mode oc

Related commands

ptp mode

ptp profile

ptp priority

Use ptp priority clock-source to configure the priority for the specified clock for GM election through BMC.

Use undo ptp priority clock-source to restore the specified priority to its default value.

Syntax

ptp priority clock-source local { priority1 priority1 | priority2 priority2 }

undo ptp priority clock-source local { priority1 | priority2 }

Default

When the PTP profile is IEEE 1588 version 2 or SMPTE ST 2059-2, the priority 1 and priority 2 values are both 128.

When the PTP profile is IEEE 802.1AS, the priority 1 value is 246 and the priority 2 value is 248.

Views

System view

Predefined user roles

network-admin

Parameters

local: Specifies the local clock.

priority1 priority1: Specifies priority 1 for the clock, in the range of 0 to 255. A numerically smaller value has higher priority.

priority2 priority2: Specifies priority 2 for the clock, in the range of 0 to 255. A numerically smaller value has higher priority.

Usage guidelines

This command is available only after you specify a PTP profile and a PTP mode.

Examples

# Set priority 1 to 10 for the local clock.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] ptp priority clock-source local priority1 10

Related commands

ptp mode

ptp profile

ptp profile

Use ptp profile to specify a PTP profile for the device.

Use undo ptp profile to restore the default.

Syntax

ptp profile { 1588v2 | 8021as | st2059-2 }

undo ptp profile

Default

PTP operates only after you specify a PTP profile.

Views

System view

Predefined user roles

network-admin

Parameters

1588v2: Specifies the IEEE 1588 version 2 PTP profile.

8021as: Specifies the IEEE 802.1AS PTP profile.

st2059-2: Specifies the SMPTE ST 2059-2 PTP profile.

Usage guidelines

Specify a PTP profile for the device before any other PTP configurations.

Changing or removing a PTP profile clears all settings under the PTP profile.

Examples

# Specify the IEEE 1588 version 2 PTP profile.

<Sysname> system-view

[Sysname] ptp profile 1588v2

ptp slave-only

Use ptp slave-only to configure the OC to operate only as a member clock.

Use undo ptp slave-only to restore the default.

Syntax

ptp slave-only

undo ptp slave-only

Default

An OC can operate either as a master clock or a member clock.

Views

System view

Predefined user roles

network-admin

Usage guidelines

This command is applicable only to OCs and is available only after you specify a PTP profile and a PTP mode.

You can execute the ptp force-state command to specify a subordinate port as a master port or passive port even if the OC operates as a member clock.

Examples

# Specify the OC clock node type for the device. Configure the OC to operate only as a member clock.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] ptp slave-only

Related commands

ptp force-state

ptp mode

ptp profile

ptp source

Use ptp source to configure the source IP address for multicast PTP messages transmitted over IPv4 UDP.

Use undo ptp source to remove the specified source IP address for multicast PTP messages transmitted over IPv4 UDP.

Syntax

ptp source ip-address [ vpn-instance vpn-instance-name ]

undo ptp source ip-address [ vpn-instance vpn-instance-name ]

Default

No source IP address is configured for multicast PTP messages transmitted over IPv4 UDP.

Views

System view

Predefined user roles

network-admin

Parameters

ip-address: Specifies the source IP address for multicast PTP messages transmitted over IPv4 UDP.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance used for communication between the local device and the peer device. The vpn-instance-name argument is a case-sensitive string of 1 to 31 characters. If the peer device belongs to the public network, do not specify this option.

Usage guidelines

This command is available only after you specify a PTP profile and a PTP mode. The IEEE 802.1AS profile does not support this command.

This command takes effect only when PTP messages are transmitted over IPv4 UDP in multicast mode.

If a PTP-enabled Layer 3 Ethernet interface has been assigned to a VPN instance, you must specify the VPN instance in the ptp source ip-address vpn-instance vpn-instance-name command.

Examples

# Configure the source IP address as 3.5.1.5 for multicast PTP messages transmitted over IPv4 UDP.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] ptp source 3.5.1.5

Related commands

ptp mode

ptp profile

ptp transport-protocol

ptp syn-interval

Use ptp syn-interval to set the interval for sending Sync messages.

Use undo ptp syn-interval to restore the default.

Syntax

ptp syn-interval interval

undo ptp syn-interval

Default

When the PTP profile is IEEE 1588 version 2, the interval argument value is 0 and the interval for sending Sync messages is 1 (20) second.

When the PTP profile is IEEE 802.1AS or SMPTE ST 2059-2, the interval argument value is –3 and the interval for sending Sync messages is 1/8 (2-3) seconds.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

interval: Specifies an exponent, to the power of which base 2 is raised to get the interval in seconds for sending Sync messages. When the PTP profile is IEEE 802.1AS, the value range for the interval argument is -4 to 6. When the PTP profile is IEEE 1588 version 2, the value range for the interval argument is -1 to 1. When the PTP profile is SMPTE ST 2059-2, the value range for the interval argument is –5 to –1.

Usage guidelines

This command is available only after you specify a PTP profile and a PTP mode.

Examples

# Set the Sync message sending interval to 2 (21) seconds on FortyGigE 1/0/1.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp syn-interval 1

Related commands

ptp mode

ptp profile

ptp transport-protocol

Use ptp transport-protocol to configure the IPv4 UDP transport protocol for PTP messages.

Use undo ptp transport-protocol to restore the default.

Syntax

ptp transport-protocol udp

undo ptp transport-protocol

Default

PTP messages are transported through IEEE 802.3 and Ethernet.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

udp: Specifies the IPv4 UDP transport protocol for PTP messages.

Usage guidelines

This command is available only after you specify a PTP profile and a PTP mode.

This command is not available for the IEEE 802.1AS or SMPTE ST 2059-2 PTP profile.

Examples

# Configure the IPv4 UDP transport protocol for PTP messages on FortyGigE 1/0/1.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp transport-protocol udp

Related commands

ptp mode

ptp profile

ptp unicast-destination

Use ptp unicast-destination to configure the destination IP address for unicast PTP messages transmitted over IPv4 UDP.

Use undo ptp unicast-destination to restore the default.

Syntax

ptp unicast-destination ip-address

undo ptp unicast-destination ip-address

Default

No destination IP address is configured for unicast PTP messages transmitted over IPv4 UDP.

Views

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

ip-address: Specifies the destination IP address for unicast PTP messages transmitted over IPv4 UDP.

Usage guidelines

This command is available only after you specify a PTP profile and a PTP mode.

The IEEE 802.1AS profile does not support this command.

This command takes effect only when PTP messages are transmitted over IPv4 UDP.

Examples

# Configure the destination IP address as 10.10.10.2 for unicast PTP messages transmitted over IPv4 UDP.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp transport-protocol udp

[Sysname-FortyGigE1/0/1] ptp unicast-destination 10.10.10.2

Related commands

ptp mode

ptp profile

ptp transport-protocol

ptp utc

Use ptp utc to add or subtract one second from the UTC scale on the specified date.

Use undo ptp utc to restore the default.

Syntax

ptp utc { leap59-date | leap61-date } date

undo ptp utc { leap59-date | leap61-date }

Default

No second is added to or subtracted from the UTC scale.

Views

System view

Predefined user roles

network-admin

Parameters

leap59-date: Subtracts one second from the UTC time scale at the last minute (23:59) on the specified date.

leap61-date: Adds one second to the UTC time scale at the last minute (23:59) on the specified date.

date: Sets the date to adjust UTC, in the format of YYYY/MM/DD. The value range for YYYY and MM is 2000 to 2035 and 1 to 12, respectively. The value range for DD depends on the specified month. For the configuration to take effect, do not specify a date earlier than the current date.

Usage guidelines

UTC is based on International Atomic Time (TAI), a high-precision atomic coordinate time scale, and adjusted by leap seconds for synchronization with astronomical time.

UTC is constantly compared with UT1 (astronomical time, reflecting the earth's rotation). The International Bureau of Weights and Measures (BIPM) will notify to add or subtract one second from the UTC time scale at the last minute on a specific date (typically June 30 or December 31) to ensure that the difference between UTC and UT1 is within one second.

You can use this command to add or subtract one second from the UTC time on the specific date as published by BIPM.

You can configure this command only after you have specified a PTP profile and PTP mode for the device.

This command takes effect only when it is configured on the master clock node and the local clock of the master clock node is the GM.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Assume that the current date is August 8, 2016. Specify the BC clock node type for the device. According to information published by BIPM, add one second to the UTC time at 23:59:60 on December 31, 2016.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode bc

[Sysname] ptp utc offset 36

[Sysname] ptp utc leap61-date 2016/12/31

Related commands

ptp mode

ptp profile

ptp utc offset

ptp utc offset

Use ptp utc offset to set the cumulative offset of UTC relative to TAI.

Use undo ptp utc offset to restore the default.

Syntax

ptp utc offset utc-offset

undo ptp utc offset

Default

The cumulative offset of UTC relative to TAI is 0 seconds.

Views

System view

Predefined user roles

network-admin

Parameters

utc-offset: Sets the cumulative offset of UTC relative to TAI, in seconds. The value range for the utc-offset argument is 0 to 999.

Usage guidelines

A time difference exists between UTC and TAI. Internet devices typically use the UTC time. To provide more accurate time, PTP also uses TAI. If the device acts as a subordinate clock node, it uses the UTC time and TAI time of the clock reference. If the device acts as the clock reference, it will calculate the TAI time based on the UTC time and synchronize the UTC and TAI time to the subordinate clocks. TAI provided by the device = Current UTC + cumulative offset + leap second.

BIPM periodically publishes the cumulative offset of UTC relative to TAI. Use the value published by BIPM to configure this command.

You can configure this command only after you have specified a PTP profile and PTP mode for the device.

This command takes effect only when it is configured on the master clock node and the local clock of the master clock node is the GM.

Examples

# According to information published by BIPM, the cumulative offset of UTC relative to TAI is 37 seconds. Set the cumulative offset of UTC relative to TAI to 37 seconds.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode bc

[Sysname] ptp utc offset 37

Related commands

ptp mode

ptp profile

ptp utc

ptp vlan

Use ptp vlan to specify a VLAN tag for PTP messages.

Use undo ptp vlan to restore the default.

Syntax

ptp vlan vlan-id [ dot1p dot1p-value ]

undo ptp vlan [ dot1p ]

Default

PTP messages do not have a VLAN tag.

Views

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Parameters

vlan vlan-id: Specifies a VLAN by its ID. The value range for the vlan-id argument is 1 to 4094.

dot1p dot1p-value: Specifies an 802.1p precedence for PTP messages, in the range of 0 to 7. The default 802.1p precedence is 7 (the highest).

Usage guidelines

This command is available only after you specify a PTP profile and a PTP mode.

Examples

# Specify VLAN 2 and set the 802.1p precedence to 6 for PTP messages.

<Sysname> system-view

[Sysname] ptp profile 1588v2

[Sysname] ptp mode oc

[Sysname] interface fortygige 1/0/1

[Sysname-FortyGigE1/0/1] ptp vlan 2 dot1p 6

Related commands

ptp mode

ptp profile

reset ptp statistics

Use reset ptp statistics to clear PTP statistics.

Syntax

reset ptp statistics [ interface interface-type interface-number ]

Views

User view

Predefined user roles

network-admin

Parameters

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command clears PTP statistics on all interfaces.

Examples

# Clear PTP statistics on FortyGigE 1/0/1.

<Sysname> reset ptp statistics interface fortygige 1/0/1

Related commands

display ptp statistics

  • Cloud & AI
  • InterConnect
  • Intelligent Computing
  • Security
  • SMB Products
  • Intelligent Terminal Products
  • Product Support Services
  • Technical Service Solutions
All Services
  • Resource Center
  • Policy
  • Online Help
All Support
  • Become a Partner
  • Partner Resources
  • Partner Business Management
All Partners
  • Profile
  • News & Events
  • Online Exhibition Center
  • Contact Us
All About Us
新华三官网