Contents

IPv6 policy-based routing commands· 1

apply next-hop· 1

description· 1

display ipv6 policy-based-route· 2

display ipv6 policy-based-route interface· 3

display ipv6 policy-based-route local 5

display ipv6 policy-based-route setup· 6

if-match acl 7

ipv6 local policy-based-route· 7

ipv6 policy-based-route (interface view) 8

ipv6 policy-based-route (system view) 9

reset ipv6 policy-based-route statistics· 10

 

IPv6 policy-based routing commands

apply next-hop

Use apply next-hop to set next hops.

Use undo apply next-hop to remove next hops.

Syntax

apply next-hop [ vpn-instance vpn-instance-name ] { ipv6-address [ direct ] [ track track-entry-number ] } &<1-2>

undo apply next-hop [ [ vpn-instance vpn-instance-name | inbound-vpn ] ipv6-address&<1-2> ]

Default

No next hops are set.

Views

IPv6 policy node view

Predefined user roles

network-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. The specified VPN instance must already exist.

ipv6-address: Specifies the IPv6 address of the next hop. If you do not specify the vpn-instance vpn-instance-name option or the inbound-vpn keyword, the next hop belongs to the public network.

direct: Specifies that the next hop must be directly connected to take effect.

track track-entry-number: Specifies a track entry by its number in the range of 1 to 1024.

&<1-2>: Indicates that the argument before it can be entered up to two times.

Usage guidelines

You can specify multiple next hops for backup in one command line or by executing this command multiple times.

With a next hop specified, the undo apply next-hop command removes the next hop.

Without any next hop specified, the undo apply next-hop command removes all next hops.

Examples

# Set a directly-connected next hop of 1::1.

<Sysname> system-view

[Sysname] ipv6 policy-based-route aa permit node 11

[Sysname-pbr6-aa-11] apply next-hop 1::1

description

Use description to configure a description for an IPv6 policy node.

Use undo description to restore the default.

Syntax

description text

undo description

Default

No description is configured for an IPv6 policy node.

Views

IPv6 policy node view

Predefined user roles

network-admin

Parameters

text: Specifies a description, a case-sensitive string of 1 to 127 characters.

Examples

# Configure the description as Officeuse for IPv6 policy node 1.

<Sysname> system-view

[Sysname] ipv6 policy-based-route 1 permit node 1

[Sysname-pbr6-1-1] description Officeuse

display ipv6 policy-based-route

Use display ipv6 policy-based-route to display IPv6 PBR policy information.

Syntax

display ipv6 policy-based-route [ policy policy-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

policy policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters. If you do not specify a policy, this command displays information for all IPv6 PBR policies.

Examples

# Display all IPv6 policy information.

<Sysname> display ipv6 policy-based-route

Policy name: aaa

  node 1 permit:

    if-match acl 2000

    apply next-hop 1000::1

Table 1 Command output

Field	Description
node 1 permit	The match mode of Node 1 is permit.
if-match acl	Compares IPv6 packets with IPv6 ACL.
apply next-hop	Specifies a next hop for permitted IPv6 packets.

 

Related commands

ipv6 policy-based-route (system view)

display ipv6 policy-based-route interface

Use display ipv6 policy-based-route interface to display IPv6 interface PBR configuration and statistics.

Syntax

display ipv6 policy-based-route interface interface-type interface-number [ slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays IPv6 interface PBR configuration and statistics for the master device.

Examples

# Display IPv6 PBR configuration and statistics on VLAN-interface 2.

<Sysname> display ipv6 policy-based-route interface vlan-interface 2

Policy based routing information for interface Vlan-inerface2(failed):

Policy name: aaa

  node 0 deny:

  Matched: 0

  node 1 permit:

    if-match acl 3999

  Matched: 0

  node 2 permit:

    if-match acl 2000

    apply next-hop 1000::1

  Matched: 0

  node 5 permit:

    if-match acl 3101

    apply next-hop 1000::1

  Matched: 0

Total matched: 0

<Sysname> display ipv6 policy-based-route interface Vlan-inerface2

Policy based routing information for interface Vlan-inerface2:

Policy name: aaa

  node 0 deny(not support):

  Matched: 0

  node 1 permit:

    if-match acl 3999

  Matched: 0

  node 2 permit(no resource):

    if-match acl 2000

    apply next-hop 1000::1

  Matched: 0

  node 5 permit:

    if-match acl 3101

    apply next-hop 1000::1

  Matched: 0 (no statistics resource)

Total matched: 0

Table 2 Command output

Field	Description
Policy based routing information for interface XXXX (failed)	IPv6 PBR configuration and statistics on the interface. This field displays failed in brackets if none of the nodes in the policy has been successfully issued to the driver. The failed status will persist even after the policy is successfully issued. To clear the failed status, you must remove the policy from the interface and then apply it on the interface again. NOTE: The failed status is available on a per-slot basis. To obtain this information, you must specify a slot number when you execute the command. ·     For a global interface (for example, a VLAN interface), which might have member physical interfaces on multiple slots, specify a slot that contains its member interfaces. ·     For a physical interface, specify its slot number.
node 0 deny(not support) node 2 permit(no resource)	Match mode of the node, permit or deny. If a node fails to be issued to the driver, the command displays the cause in brackets, which include: ·     not support—The device does not support the match criteria configured on the node. ·     no resource—No sufficient resources (for example, ACLs) are available for the node. NOTE: The cause is available only on a per-slot basis. To obtain this information, you must specify a slot number when you execute the command. ·     For a global interface (for example, a VLAN interface), which might have member physical interfaces on multiple slots, specify a slot that contains its member interfaces. ·     For a physical interface, specify its slot number.
if-match acl	Compares IPv6 packets with the IPv6 ACL.
apply next-hop	Specifies a next hop for permitted IPv6 packets.
Matched: 0 (no statistics resource)	Number of successful matches on the node. If the device does not have sufficient resources to count matches, this field displays no statistics resource in brackets. NOTE: The statistics collection failure cause is available only on a per-slot basis. To obtain this information, you must specify a slot number when you execute the command. ·     For a global interface (for example, a VLAN interface), which might have member physical interfaces on multiple slots, specify a slot that contains its member interfaces. ·     For a physical interface, specify its slot number.
Total matched	Total number of successful matches on all nodes.

 

Related commands

reset ipv6 policy-based-route statistics

display ipv6 policy-based-route local

Use display ipv6 policy-based-route local to display IPv6 local PBR configuration and statistics.

Syntax

display ipv6 policy-based-route local [ slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays IPv6 local PBR configuration and statistics for the master device.

Examples

# Display IPv6 local PBR configuration and statistics.

<Sysname> display ipv6 policy-based-route local

Policy based routing information for local:

Policy name: aaa

  node 0 deny:

  Matched: 0

  node 1 permit:

    if-match acl 3999

  Matched: 0

  node 2 permit:

    if-match acl 2000

    apply next-hop 1::1

  Matched: 0

  node 5 permit:

    if-match acl 3101

    apply next-hop 2::2

  Matched: 0

Total matched: 0

Table 3 Command output

Field	Description
Policy based routing information for local	IPv6 local PBR configuration and statistics.
node 0 deny/node 2 permit	Match mode of the node, permit or deny.
if-match acl	Compares packets with the ACL.
apply next-hop	Specifies a next hop for permitted packets.
Matched: 0	Number of successful matches on the node.
Total matched	Total number of successful matches on all nodes.

 

Related commands

reset ipv6 policy-based-route statistics

display ipv6 policy-based-route setup

Use display ipv6 policy-based-route setup to display IPv6 PBR configuration.

Syntax

display ipv6 policy-based-route setup

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display IPv6 PBR configuration.

<Sysname> display ipv6 policy-based-route setup

Policy name              Type               Interface

pr01                     Forward            Vlan-interface 2

pr02                     Local              N/A

pr03                     Global             N/A

Table 4 Command output

Field	Description
Policy name	Policy name.
Type	Type of the PBR: ·     Forward—Interface PBR. ·     Local—Local PBR. ·     Global—Global PBR.
Interface	Interface where the policy is applied. This field displays N/A for IPv6 local PBR and IPv6 global PBR.

 

Related commands

ipv6 policy-based-route (interface view)

if-match acl

Use if-match acl to set an ACL match criterion.

Use undo if-match acl to restore the default.

Syntax

if-match acl { ipv6-acl-number | name ipv6-acl-name }

undo if-match acl

Default

No ACL match criterion is set.

Views

IPv6 policy node view

Predefined user roles

network-admin

Parameters

ipv6-acl-number: Specifies an IPv6 ACL by its number in the range of 2000 to 3999. The value range of a basic ACL is 2000 to 2999 and that of an advanced ACL is 3000 to 3999.

name ipv6-acl-name: Specifies an IPv6 ACL by its name, a case-insensitive string of 1 to 63 characters starting with a letter. The ACL name cannot be all. For the command to take effect, make sure the specified IPv6 ACL is a basic or advanced ACL.

Examples

# Configure Node 10 of policy aa to permit the packets matching ACL 2000.

<Sysname> system-view

[Sysname] ipv6 policy-based-route aa permit node 10

[Sysname-pbr6-aa-10] if-match acl 2000

# Configure Node 10 of policy aa to permit the packets matching ACL aaa.

<Sysname> system-view

[Sysname] ipv6 policy-based-route aa permit node 10

[Sysname-pbr6-aa-10] if-match acl name aaa

ipv6 local policy-based-route

Use ipv6 local policy-based-route to configure IPv6 local PBR based on a specified policy.

Use undo ipv6 local policy-based-route to restore the default.

Syntax

ipv6 local policy-based-route policy-name

undo ipv6 local policy-based-route

Default

No policy is referenced for IPv6 local PBR.

Views

System view

Predefined user roles

network-admin

Parameters

policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters. The specified IPv6 policy must already exist.

Usage guidelines

You can apply only one policy locally. Before you apply a new policy, you must first remove the current policy.

IPv6 local PBR is used to route locally generated packets except the packets destined for the sender. This feature might affect local services. Do not configure IPv6 local PBR unless doing so is required.

Examples

# Configure IPv6 local PBR based on policy aaa.

<Sysname> system-view

[Sysname] ipv6 local policy-based-route aaa

Related commands

display ipv6 policy-based-route setup

ipv6 policy-based-route (system view)

ipv6 policy-based-route (interface view)

Use ipv6 policy-based-route to configure IPv6 interface PBR by applying an IPv6 policy to an interface.

Use undo ipv6 policy-based-route to restore the default.

Syntax

ipv6 policy-based-route policy-name

undo ipv6 policy-based-route

Default

No IPv6 policy is applied to an interface.

Views

Interface view

Predefined user roles

network-admin

Parameters

policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters. The specified policy must already exist.

Examples

# Apply policy aaa to VLAN-interface 2.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] ipv6 policy-based-route aaa

Related commands

display ipv6 policy-based-route setup

ipv6 policy-based-route (system view)

ipv6 policy-based-route (system view)

Use ipv6 policy-based-route to create an IPv6 policy node and enter its view, or enter the view of an existing IPv6 policy node.

Use undo ipv6 policy-based-route to delete an IPv6 policy or IPv6 policy node.

Syntax

ipv6 policy-based-route policy-name [ deny | permit ] node node-number

undo ipv6 policy-based-route policy-name [ deny | node node-number | permit ]

Default

No IPv6 policy nodes exist.

Views

System view

Predefined user roles

network-admin

Parameters

policy-name: Specifies a policy name, a case-sensitive string of 1 to 19 characters.

deny: Specifies the match mode for the policy node as deny.

permit: Specifies the match mode for the policy node as permit (default mode).

node node-number: Specifies the number of the IPv6 policy node. A smaller number has a higher priority. The value range for the node-number argument is 0 to 255.

Usage guidelines

To delete an IPv6 policy that has already applied to an interface, you must delete the policy from the interface first.

If a policy node is specified, the undo ipv6 policy-based-route command deletes the specified policy node. If a match mode is specified, the command deletes all nodes configured with the match mode. If no node is specified, the command deletes the whole policy.

Examples

# Create permit-mode Node 10 for IPv6 policy aaa and enter its view.

<Sysname> system-view

[Sysname] ipv6 policy-based-route aaa permit node 10

[Sysname-pbr6-aaa-10]

Related commands

display ipv6 policy-based-route

reset ipv6 policy-based-route statistics

Use reset ipv6 policy-based-route statistics to clear IPv6 PBR statistics.

Syntax

reset ipv6 policy-based-route statistics [ policy policy-name ]

Views

User view

Predefined user roles

network-admin

Parameters

policy policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters. If you do not specify a policy, this command clears IPv6 PBR statistics for all policies.

Examples

# Clear all IPv6 PBR statistics.

<Sysname> reset ipv6 policy-based-route statistics

Related commands

display ipv6 policy-based-route interface

display ipv6 policy-based-route local