Network Address Translation (NAT) translates an IP address in the IP packet header to another IP address. Typically, NAT is configured on gateways to enable private hosts to access external networks and external hosts to access private network resources such as a Web server.

Basic NAT concepts

The following describes basic NAT concepts:

· NAT device—A device configured with NAT. Typically, NAT is configured on the edge device that connects the internal and external networks.

· NAT interface—An interface configured with NAT.

· NAT rule—A rule that NAT follows to translate addresses.

· NAT address—A public IP address used for address translation, and this address is reachable from the external network. The NAT address can be manually assigned or dynamically obtained.

· NAT entry—Stores the mapping between a private IP address and a public IP address. For more information, see "NAT entries."

· Easy IP—Uses the IP address of an interface as the NAT address. The IP address of the interface can be manually assigned or be obtained through DHCP.

Basic NAT operating mechanism

Figure 1 shows the basic NAT operating mechanism.

1. Upon receiving a request from the host to the server, NAT translates the private source address 192.168.1.3 to the public address 20.1.1.1 and forwards the NATed packet. NAT adds a mapping for the two addresses to its NAT table.

2. Upon receiving a response from the server, NAT translates the destination public address to the private address, and forwards the packet to the host.

The NAT operation is transparent to the terminals (the host and the server). NAT hides the private network from the external users and shows that the IP address of the internal host is 20.1.1.1.

Figure 1 Basic NAT operation

‌

NAT applications

Traditional NAT

Traditional NAT is configured on the interface that connects to the public network. It translates the source IP addresses of outgoing packets and destination IP addresses of incoming packets.

Twice NAT

Twice NAT translates the destination IP address on the receiving interface, and the source IP address on the sending interface. The receiving and sending interfaces are both NAT interfaces.

Twice NAT allows VPNs with overlapping addresses to access each other.

Bidirectional NAT

NAT translates the source and destination IP addresses of incoming packets on the receiving interface and outgoing packets on the sending interface.

Bidirectional NAT supports active access to external network resources from internal users when the internal and external IP addresses overlap.

NAT hairpin

NAT hairpin allows internal hosts to access each other through NAT. The source and destination IP address of the packets are translated on the interface connected to the internal network.

NAT hairpin includes P2P and C/S modes:

· P2P—Allows internal hosts to access each other through NAT. The internal hosts first register their public addresses to an external server. Then, the hosts communicate with each other by using the registered IP addresses.

· C/S—Allows internal hosts to access internal servers through NAT addresses. The destination IP address of the packet going to the internal server is translated by matching the NAT Server configuration. The source IP address is translated by matching the outbound dynamic or static NAT entries.

NAT DNS mapping

The DNS server is typically on the public network. For the users on the public network to access an internal server, you can configure the NAT Server feature on the NAT interface that connects to the public network. The NAT Server maps the public IP address and port number to the private IP address and port number of the internal server. Then the public users can access the internal server through the server's domain name or public IP address.

When a user is in the private network, the user cannot access the internal server by using the domain name of the server. This is because the DNS response contains the public IP address of the server. In this case, you can configure NAT DNS mapping to solve the problem.

Figure 2 NAT DNS mapping

‌

As shown in Figure 2, NAT DNS mapping works as follows:

3. The host sends a DNS request containing the domain name of the internal Web server.

4. Upon receiving the DNS response, the NAT device performs a DNS mapping lookup by using the domain name in the response. A NAT DNS mapping maps the domain name to the public IP address, public port number, and the protocol type for the internal server.

5. If a match is found, the NAT continues to compare the public address, public port number, and the protocol type with the NAT Server configuration. The NAT Server configuration maps the public IP address and port number to the private IP address and port number for the internal server.

6. If a match is found, NAT translates the public IP address in the response into the private IP address of the Web server.

7. The internal host receives the DNS response, and obtains the private IP address of the Web server.

NAT control

You can use ACLs to implement NAT control. The match criteria in the ACLs include the source IP address, source port number, destination IP address, destination port number, transport layer protocol, user group, and VPN instance. Only packets permitted by an ACL are processed by NAT.

NAT translation methods

Static NAT

Static NAT creates a fixed mapping between a private address and a public address. It supports connections initiated from internal users to external network and from external users to the internal network. Static NAT applies to regular communications.

Dynamic NAT

Dynamic NAT uses an address pool to translate addresses. It applies to the scenario where a large number of internal users access the external network.

NO-PAT

Not Port Address Translation (NO-PAT) translates a private IP address to an IP public address. The public IP address cannot be used by another internal host until it is released.

NO-PAT supports all IP packets.

PAT

Port Address Translation (PAT) translates multiple private IP addresses to a single public IP address by mapping the private IP address and source port to the public IP address and a unique port. PAT supports TCP and UDP packets, and ICMP request packets.

Figure 3 PAT operation

‌

As shown in Figure 3, PAT translates the source IP addresses of the three packets to the same IP public address and translates their port numbers to different port numbers. Upon receiving a response, PAT translates the destination address and port number of the response, and forwards it to the target host.

PAT supports the following mappings:

· Endpoint-Independent Mapping (EIM)—Uses the same IP and port mapping (EIM entry) for packets from the same source IP and port to any destinations. EIM allows external hosts to initiate connections to the translated IP addresses and ports of internal hosts. It allows internal hosts behind different NAT gateways to access each other.

· Address and Port-Dependent Mapping (APDM)—Uses different IP and port mappings for packets from the same source IP and port to different destination IP addresses and ports. APDM allows an external host to initiate connections to an internal host only under the condition that the internal host has previously accessed the external host. It is secure, but it does not allow internal hosts behind different NAT gateways to access each other.

NAT Server

The NAT Server feature maps a public address and port number to the private IP address and port number of an internal server. This feature allows servers in the private network to provide services for external users.

Figure 4 shows how NAT Server works:

1. Upon receiving a request from the host, NAT translates the public destination IP address and port number to the private IP address and port number of the internal server.

2. Upon receiving a response from the server, NAT translates the private source IP address and port number to the public IP address and port number.

Figure 4 NAT Server operation

‌

Port block-based NAT

Port block-based NAT is a PAT translation based on port ranges. It maps multiple private IP addresses to one public IP address and uses a different port block for each private IP address. For example, the private IP address 10.1.1.1 of an internal host is mapped to the public IP address 202.1.1.1 and port block 10001 to 10256. When the internal host accesses public hosts, the source IP address 10.1.1.1 is translated to 202.1.1.1, and the source ports are translated to ports in the port block 10001 to 10256.

Port block-based NAT includes static and dynamic mappings. It applies to NAT444 and DS-Lite networks.

Static port block mapping

The NAT gateway computes a static port block mapping before address translation. The mapping is between a private IP address and a public IP address with a port block.

When an internal user initiates a connection to the external network, the system performs the following operations:

· Locates a static mapping based on the private IP address of the user and obtains the public IP address and the port block in the mapping.

· Selects a public port number in the port block.

· Translates the private IP address to the public IP address and assigns the selected public port number.

The NAT gateway uses private IP addresses, public IP addresses, a port range, and a port block size to compute static mappings:

1. Divides the port range by the port block size to get the number of available port blocks for each public IP address.

This value is the base number for mapping.

2. Sorts the port blocks in ascending order of the start port number in each block.

3. Sorts the private IP addresses and the public IP addresses separately in ascending order.

4. Maps the first base number of private IP addresses to the first public IP address and its port blocks in ascending order.

For example, the number of available port blocks of each public IP address is m. The first m private IP addresses are mapped to the first public IP address and the m port blocks in ascending order. The next m private IP addresses are mapped to the second IP address and the m port blocks in ascending order. The other static port block mappings are created by analogy.

Dynamic port block mapping

When an internal user initiates a connection to the external network, the dynamic port block-based NAT operates as follows:

1. Uses ACLs to implement translation control. It processes only packets that match an ACL permit rule.

2. Creates a mapping from the internal user's private IP address to a public IP address and a port block.

3. Translates the private IP address to the public IP address, and the source ports to ports in the selected port block for subsequent connections from the private IP address.

4. Withdraws the port block and deletes the dynamic port block mapping when all connections from the private IP address are disconnected.

Dynamic port block mapping supports port block extending. If the ports in the port block for a private address are all occupied, dynamic port block mapping translates the source port to a port in an extended port block.

NAT entries

NAT session entry

NAT creates a NAT session entry for a session and creates an address mapping for the first packet in the session.

A NAT session entry contains extended NAT information, such as interface and translation method. Subsequent packets of the session are translated by using this entry.

· If the direction of the subsequent packets is the same as the direction of the first translated packet, NAT performs the source and destination address translation the same as the first packet.

· If the direction of the subsequent packets is opposite to the direction of the first translated packet, NAT perform reverse address translation. For example, if the source address of the first packet is translated, then the destination address of the subsequent packets is translated.

The session management module maintains the updating and aging of NAT session entries. For information about session management, see Security Configuration Guide.

EIM entry

If EIM is configured on the NAT device, the PAT mode will first create a NAT session entry, and then an EIM entry. The EIM entry is a 3-tuple entry, and it maps a private address/port to a public address/port. The EIM entry ensures:

· Subsequent new connections originating from the same source IP and port uses the same translation as the initial connection.

· Translates the address for new connections initiated from external hosts to the NAT address and port number based on the EIM entry.

An EIM entry ages out after all related NAT session entries age out.

NO-PAT entry

A NO-PAT entry maps a private address to a public address. The same mapping applies to subsequent connections originating from the same source IP.

A NO-PAT entry can also be created during the ALG process for NAT. For information about NAT ALG, see "NAT ALG."

A NO-PAT entry ages out after all related NAT session entries age out.

Port block-based entry

A port block-based entry maps a private IP address to a public IP address and a port block.

Port block-based entries include static and dynamic port block mappings. For information about these mappings, see "Static port block mapping" and "Dynamic port block mapping."

VRF-aware NAT

VRF-aware NAT allows users from different VRF (VPN instances) to access external networks and to access each other.

1. Upon receiving a request from a user in a VRF to an external network, NAT performs the following tasks:

¡ Translates the private source IP address and port number to a public IP address and port number.

¡ Records the VRF information, such as the VRF name.

2. When a response packet arrives, NAT performs the following tasks:

¡ Translates the destination public IP address and port number to the private IP address and port number.

¡ Forwards the packet to the target VRF.

The NAT Server feature supports VRF-aware NAT for external users to access the servers in a VPN instance. For example, to enable a host at 10.110.1.1 in VPN 1 to provide Web services for Internet users, configure NAT Server to use 202.110.10.20 as the public IP address of the Web server.

NAT ALG

NAT ALG (Application Level Gateway) translates address or port information in the application layer payloads to ensure connection establishment.

For example, an FTP application includes a data connection and a control connection. The IP address and port number for the data connection depend on the payload information of the control connection. This requires NAT ALG to translate the address and port information for data connection establishment.

Configuring NAT

Restrictions and guidelines: NAT configuration

The general restrictions and guidelines are as follows:

· If you perform all the translation methods, the NAT rules are sorted in the following descending order:

a. NAT Server.

b. Static NAT.

c. NAT static port blocking mapping.

d. Dynamic NAT and NAT dynamic port block mapping.

Dynamic NAT and NAT dynamic port block mapping have the same priority.

Dynamic NAT rules and NAT dynamic port block mapping rules are sorted in descending order of ACL numbers and are effective for IPv4 packets.

Interface-based NAT tasks at a glance

To configure NAT on an interface, perform the following tasks:

1. Configuring a translation method on an interface

¡ Configuring static NAT

¡ Configuring outbound dynamic NAT for interface-based NAT

¡ Configuring common NAT server mappings on an interface

¡ Configuring load sharing NAT server mappings on an interface

¡ Configuring ACL-based NAT server mappings on an interface

¡ Configuring static port block mapping on an interface

¡ Configuring dynamic port block mapping on an interface

2. Enabling flow-triggered port block assignment

3. (Optional.) Configuring NAT hairpin

4. (Optional.) Configuring NAT DNS mapping

5. (Optional.) Configuring NAT ALG

6. (Optional.) Configuring NAT logging

Configuring static NAT

Prerequisites for static NAT configuration

Before configuring static NAT, you must configure an ACL to identify the IP addresses to be translated. For more information about ACLs, see ACL and QoS Configuration Guide.

Configuring outbound one-to-one static NAT

About this task

For address translation from a private IP address to a public IP address, configure outbound one-to-one static NAT on the interface connected to the external network.

· When the source IP address of a packet from the private network matches the local-ip, the source IP address is translated into the global-ip.

· When the destination IP address of a packet from the public network matches the global-ip, the destination IP address is translated into the local-ip.

Configuring outbound one-to-one static NAT on an interface

1. Enter system view.

system-view

2. Configure a one-to-one mapping for outbound static NAT.

nat static outbound local-ip [ vpn-instance local-vpn-instance-name ] global-ip [ vpn-instance global-vpn-instance-name ] [ acl { ipv4-acl-number | name ipv4-acl-name } [ reversible ] ]

3. Enter interface view.

interface interface-type interface-number

4. Enable static NAT on the interface.

nat static enable

By default, static NAT is disabled.

Configuring outbound net-to-net static NAT

About this task

For address translation from a private network to a public network, configure outbound net-to-net static NAT on the interface connected to the external network.

· When the source IP address of a packet from the private network matches the private address range, the source IP address is translated into a public address in the public address range.

· When the destination IP address of a packet from the public network matches the public address range, the destination IP address is translated into a private address in the private address range.

Configuring outbound net-to-net static NAT on an interface

1. Enter system view.

system-view

2. Configure a net-to-net mapping for outbound static NAT.

nat static outbound net-to-net local-start-address local-end-address [ vpn-instance local-vpn-instance-name ] global global-network { mask-length | mask } [ vpn-instance global-vpn-instance-name ] [ acl { ipv4-acl-number | name ipv4-acl-name } [ reversible ] ]

3. Enter interface view.

interface interface-type interface-number

4. Enable static NAT on the interface.

nat static enable

By default, static NAT is disabled.

Configuring dynamic NAT

Restrictions and guidelines for dynamic NAT configuration

You can configure multiple inbound or outbound dynamic NAT rules.

· A NAT rule with an ACL takes precedence over a rule without any ACL.

· If two ACL-based dynamic NAT rules are configured, the rule with the higher ACL number has higher priority.

Prerequisites for dynamic NAT configuration

Before configuring dynamic NAT, you must perform the following tasks:

· Configure an ACL to identify the IP addresses to be translated. For more information about ACLs, see ACL and QoS Configuration Guide.

· Determine whether to enable the Easy IP feature. If you use the IP address of an interface as the NAT address, you are configuring Easy IP.

· Determine a public IP address range for address translation.

· Determine whether to translate port numbers. Use NO-PAT to translate only IP addresses and PAT to translate both IP addresses and port numbers.

Configuring outbound dynamic NAT

About this task

Outbound dynamic NAT translates private IP addresses into public IP addresses.

Restrictions and guidelines

Interface-based outbound dynamic NAT is typically configured on the interface connected to the external network.

Configuring outbound dynamic NAT for interface-based NAT

1. Enter system view.

system-view

2. (Optional.) Specify the Endpoint-Independent Mapping mode for outbound dynamic PAT.

nat mapping-behavior endpoint-independent [ acl { ipv4-acl-number | name ipv4-acl-name } ]

The default mapping mode is Address and Port-Dependent Mapping.

This command takes effect only on outbound dynamic NAT for PAT.

3. Create a NAT address group and enter its view.

nat address-group group-id

4. Add an address range to the address group.

address start-address end-address

By default, an address group does not have any address ranges.

You can add multiple address ranges to an address group, but the address ranges must not overlap.

5. Return to system view.

quit

6. Enter interface view.

interface interface-type interface-number

7. Configure outbound dynamic NAT on the interface. Choose the options to configure as needed:

¡ Configure NO-PAT.

nat outbound [ ipv4-acl-number | name ipv4-acl-name ] address-group group-id [ vpn-instance vpn-instance-name ] no-pat [ reversible ]

¡ Configure PAT.

nat outbound [ ipv4-acl-number | name ipv4-acl-name ] [ address-group group-id ] [ vpn-instance vpn-instance-name ] [ port-preserved ]

You can configure multiple outbound dynamic NAT rules on an interface.

Parameter	Description
address-group	If you do not specify this keyword, the IP address of the interface is used as the NAT address. Easy IP is implemented.
no-pat reversible	If you specify these keywords, you enable reverse address translation. Reverse address translation uses existing NO-PAT entries to translate the destination address for connections actively initiated from the external network to the internal network. The destination address is translated into the private IP address in the matching NO-PAT entry.

‌

Configuring NAT server mappings

About NAT server mappings

Typically, the NAT Server feature is configured on the NAT device to allow servers in the private network or VPN instance to provide services for external users. It maps a public IP address and port number to the private IP address and port number of the internal server.

The NAT Server feature can be implemented by the following methods:

· Common NAT server mappings—Maps the private IP address and the port number of the internal server to a public IP address and a port number. This method allows external hosts to access the internal server by using the specified public IP address.

· Load sharing NAT server mappings—You can add multiple internal servers to an internal server group so that these servers provide the same service for external hosts. The NAT device chooses one internal server based on the weight and number of connections of the servers to respond to a request from an external host to the public address of the internal server group.

· ACL-based NAT server mappings—An extension of common NAT server mapping. A common NAT server mapping maps the private IP address of the internal server to a single public IP address. An ACL-based NAT server mapping the private IP address of the internal server to a set of public IP addresses defined by an ACL. If the destination address of a packet matches a permit rule in the ACL, the destination address is translated into the private IP address of the internal server.

Configuring common NAT server mappings on an interface

Restrictions and guidelines

Typically, interface-based NAT server mappings are configured on the interface connected to the external network.

Procedure

1. Enter system view.

system-view

2. Enter interface view.

interface interface-type interface-number

3. Configure common NAT server mappings. Choose the options to configure as needed:

¡ A single public address with a single or no public port:

nat server [ protocol pro-type ] global { global-address | current-interface | interface interface-type interface-number } [ global-port ] [ vpn-instance global-vpn-instance-name ] inside local-address [ local-port ] [ vpn-instance local-vpn-instance-name ] [ acl { ipv4-acl-number | name ipv4-acl-name } ] [ reversible ]

¡ A single public address with consecutive public ports:

nat server protocol pro-type global { global-address | current-interface | interface interface-type interface-number } global-port1 global-port2 [ vpn-instance global-vpn-instance-name ] inside { { local-address | local-address1 local-address2 } local-port | local-address local-port1 local-port2 } [ vpn-instance local-vpn-instance-name ] [ acl { ipv4-acl-number | name ipv4-acl-name } ]

¡ Consecutive public addresses with no public port:

nat server protocol pro-type global global-address1 global-address2 [ vpn-instance global-vpn-instance-name ] inside { local-address | local-address1 local-address2 } [ local-port ] [ vpn-instance local-vpn-instance-name ] [ acl { ipv4-acl-number | name ipv4-acl-name } ]

¡ Consecutive public addresses with a single public port:

nat server protocol pro-type global global-address1 global-address2 global-port [ vpn-instance global-vpn-instance-name ] inside { local-address [ local-port1 local-port2 ] | [ local-address | local-address1 local-address2 ] [ local-port ] } [ vpn-instance local-vpn-instance-name ] [ acl { ipv4-acl-number | name ipv4-acl-name } ]

You can configure multiple NAT server mappings on an interface.

Configuring load sharing NAT server mappings on an interface

Restrictions and guidelines

When you configure load shared internal servers, you must make sure a user uses the same public address and public port to access the same service on an internal server. For this purpose, make sure value N in the following mappings is equal to or less than the number of servers in the internal server group:

· One public address and N consecutive public port numbers are mapped to one internal server group.

· N consecutive public addresses and one public port number are mapped to one internal server group.

Procedure

1. Enter system view.

system-view

2. Create a NAT Server group and enter its view.

nat server-group group-id

By default, no NAT Server groups exist.

3. Add an internal server into the group.

inside ip inside-ip port port-number [ weight weight-value ]

You can add multiple internal servers to a group.

4. Return to system view.

quit

5. Enter interface view.

interface interface-type interface-number

6. Configure load sharing NAT server mapping.

nat server protocol pro-type global { { global-address | current-interface | interface interface-type interface-number } { global-port | global-port1 global-port2 } | global-address1 global-address2 global-port } [ vpn-instance global-vpn-instance-name ] inside server-group group-id [ vpn-instance local-vpn-instance-name ] [ acl { ipv4-acl-number | name ipv4-acl-name } ]

You can configure multiple load sharing NAT server mappings on an interface.

Configuring ACL-based NAT server mappings on an interface

1. Enter system view.

system-view

2. Enter interface view.

interface interface-type interface-number

3. Configure ACL-based NAT server mapping.

nat server global { ipv4-acl-number | name ipv4-acl-name } inside local-address [ local-port ] [ vpn-instance local-vpn-instance-name ]

You can configure multiple NAT server mappings on an interface.

Configuring port block-based NAT

About port block-based NAT

Port block-based NAT provides outbound address translation. For example in NAT444 application, by configuring port block-based NAT address translation on the NAT444 gateway, multiple private IP addresses are mapped to one public IP address and a different port block is used for each private IP address

Restrictions and guidelines for port block-based NAT configuration

To configure dynamic port block mapping, you must configure port block parameters in the NAT address group.

Configuring static port block mapping on an interface

Restrictions and guidelines

Interface-based static port block mappings are typically configured on the interface connected to the public network

Procedure

1. Enter system view.

system-view

2. Create a NAT port block group, and enter its view.

nat port-block-group group-id

3. Add a private IP address range to the port block group.

local-ip-address start-address end-address

You can add multiple private IP address ranges to one port block group, but they cannot overlap.

4. Add a public IP address range to the port block group.

global-ip-pool start-address end-address

You can add multiple public IP address ranges to one port block group, but they cannot overlap.

5. Configure the port range for the public IP addresses.

port-range start-port-number end-port-number

By default, the port range is 1 to 65535.

6. Set the port block size.

block-size block-size

By default, the port block size is 256.

7. (Optional.) Set the maximum number of ports that can be assigned for a protocol.

port-limit { icmp | tcp | total | udp } number

By default, no upper limit is set for a protocol.

8. Return to system view.

quit

9. Enter interface view.

interface interface-type interface-number

10. Apply the port block group to the outbound direction of the interface.

nat outbound port-block-group group-id

By default, no port block group is applied to the interface.

You can apply multiple port block groups to one interface.

11. (Optional.) Execute the following commands in sequence to specify the Endpoint-Independent Mapping mode for PAT.

quit

nat mapping-behavior endpoint-independent [ acl { ipv4-acl-number | name ipv4-acl-name } ]

The default mapping mode is Address and Port-Dependent Mapping.

Configuring dynamic port block mapping on an interface

Procedure

1. Enter system view.

system-view

2. (Optional.) Specify the Endpoint-Independent Mapping mode for PAT.

nat mapping-behavior endpoint-independent [ acl { ipv4-acl-number | name ipv4-acl-name } ]

The default mapping mode is Address and Port-Dependent Mapping.

3. Create a NAT address group, and enter its view.

nat address-group group-id

4. Add a public IP address range to the NAT address group.

address start-address end-address

You can add multiple public IP address ranges to an address group, but the IP address ranges in address groups cannot overlap.

5. (Optional.) Configure the port range for the public IP addresses.

port-range start-port-number end-port-number

By default, the port range is 1 to 65535.

The configuration takes effect only on PAT translation mode.

6. (Optional.) Set the maximum number of ports that can be assigned for a protocol.

port-limit { icmp | tcp | total | udp } number

By default, no upper limit is set for a protocol.

7. Configure port block parameters.

port-block block-size block-size [ extended-block-number extended-block-number [ extended-block-size extended-block-size] ]

By default, no port block parameters exist.

The configuration takes effect only on PAT translation mode.

8. Return to system view.

quit

9. Enter interface view.

interface interface-type interface-number

10. Configure PAT for outbound dynamic NAT.

nat outbound [ ipv4-acl-number | name ipv4-acl-name ] [ address-group group-id ] [ vpn-instance vpn-instance-name ] [ port-preserved ]

By default, no outbound dynamic NAT rules exist.

The port-preserved keyword does not take effect on dynamic port block mappings.

Enabling flow-triggered port block assignment

1. Enter system view.

system-view

2. Enable flow-triggered port block assignment.

nat port-block flow-trigger enable

By default, flow-triggered port block assignment is disabled.

Configuring NAT hairpin

Restrictions and guidelines

NAT hairpin works in conjunction with NAT Server, outbound dynamic NAT, or outbound static NAT. To provide service correctly, you must configure NAT hairpin on the same interface module as its collaborative NAT feature.

To configure the P2P mode, you must configure outbound PAT on the interface connected to the external network and enable the EIM mapping mode.

Procedure

1. Enter system view.

system-view

2. Enter interface view.

interface interface-type interface-number

3. Enable NAT hairpin.

nat hairpin enable

By default, NAT hairpin is disabled.

Configuring NAT DNS mapping

Restrictions and guidelines

NAT DNS mapping works in conjunction with NAT Server. NAT DNS mapping maps the domain name of an internal server to the public IP address, public port number, and protocol type of the internal server. NAT Server maps the public IP and port to the private IP and port of the internal server.

Procedure

1. Enter system view.

system-view

2. Configure a NAT DNS mapping.

nat dns-map domain domain-name protocol pro-type { interface interface-type interface-number | ip global-ip } port global-port

You can configure multiple NAT DNS mappings.

Configuring NAT ALG

1. Enter system view.

system-view

2. Configure NAT ALG for a protocol or all protocols.

nat alg { all | dns | ftp | h323 | icmp-error | ils | mgcp | nbt | pptp | rsh | rtsp | sccp | sip | sqlnet | tftp | xdmcp }

By default, NAT ALG is disabled for all supported protocols except for FTP, ICMP error packets, and RTSP.

Configuring NAT logging

Configuring NAT session logging

About this task

NAT session logging records NAT session information, including translation information and access information.

A NAT device generates NAT session logs for the following events:

· NAT session establishment.

· NAT session removal. This event occurs when you add a configuration with a higher priority, remove a configuration, change ACLs, when a NAT session ages out, or when you manually delete a NAT session.

· Active NAT session logging.

Procedure

1. Enter system view.

system-view

2. Enable NAT logging.

nat log enable [ acl { ipv4-acl-number | name ipv4-acl-name } ]

By default, NAT logging is disabled.

3. Enable NAT session logging.

¡ For NAT session establishment events:

nat log flow-begin

¡ For NAT session removal events:

nat log flow-end

¡ For active NAT flows:

nat log flow-active minutes

By default, NAT session logging is disabled.

Configuring NAT444 user logging

About this task

The NAT444 gateway generates a user log whenever it assigns or withdraws a port block. The log includes the private IP address, public IP address, and port block.

A NAT444 gateway generates NAT user logs when one of the following events occurs:

· A port block is assigned.

For the NAT444 static port block mapping, the NAT444 gateway generates a user log when it translates the first connection from a private IP address.

For the NAT444 dynamic port block mapping, the NAT444 gateway generates a user log when it assigns or extends a port block for a private IP address.

· A port block is withdrawn.

For the NAT444 static port block mapping, the NAT444 gateway generates a user log when all connections from a private IP address are disconnected.

For the NAT444 dynamic port block mapping, the NAT444 gateway generates a user log when all the following conditions are met:

¡ All connections from a private IP address are disconnected.

¡ The port blocks (including the extended ones) assigned to the private IP address are withdrawn.

¡ The corresponding mapping entry is deleted.

Prerequisites

Before configuring NAT444 user logging, you must configure the custom log outputting feature. The NAT444 user logs can be exported by the fast log output or flow log output feature. For more information, see fast log output in Network Management and Monitoring Configuration Guide.

Procedure

1. Enter system view.

system-view

2. Enable NAT logging.

nat log enable [ acl { ipv4-acl-number | name ipv4-acl-name } ]

By default, NAT logging is disabled.

The acl keyword does not take effect on NAT444 user logging.

3. Enable NAT444 user logging. Choose the options to configure as needed:

¡ For port block assignment:

nat log port-block-assign

¡ For port block withdrawal:

nat log port-block-withdraw

By default, NAT444 user logging is disabled.

Configuring NAT port block assignment failure logging

About this task

The system generates logs when the system fails port block assignment.

Procedure

1. Enter system view.

system-view

2. Enable NAT logging.

nat log enable [ acl { ipv4-acl-number | name ipv4-acl-name } ]

By default, NAT logging is disabled.

3. Enable logging for port block assignment failures.

nat log port-block-alloc-fail

By default, logging is disabled for port block assignment failures.

Configuring NAT port allocation failure logging

About this task

The system generates logs when port allocation fails in dynamic NAT. Typically, the failure is caused by the fact that all ports are occupied in a port block.

Prerequisites

Before configuring this feature, you must configure the custom log outputting feature. The NAT port allocation failure logs can be exported by using the fast log output or flow log output feature. For more information, see fast log output in Network and Monitoring Configuration Guide.

Procedure

1. Enter system view.

system-view

2. Enable NAT logging.

nat log enable [ acl { ipv4-acl-number | name ipv4-acl-name } ]

By default, NAT logging is disabled.

3. Enable logging for NAT port allocation failures.

nat log port-alloc-fail

By default, logging is disabled for NAT port allocation failures.

Display and maintenance commands for NAT

Execute display commands in any view and reset commands in user view.

Task	Command
Display all NAT configuration information.	display nat all
Display NAT address group information.	display nat address-group [ group-id ]
Display NAT DNS mapping configuration.	display nat dns-map
Display information about NAT EIM entries.	display nat eim [ chassis chassis-number slot slot-number [ cpu cpu-number ] ] [ protocol { icmp \| tcp \| udp } ] [ local-ip { local-ip } ] [ local-port local-port ] [ global-ip global-ip ] [ global-port global-port ]
Display NAT EIM entry statistics.	display nat eim statistics [ chassis chassis-number slot slot-number [ cpu cpu-number ] ]
Display NAT logging configuration.	display nat log
Display information about NAT NO-PAT entries.	display nat no-pat [ chassis chassis-number slot slot-number [ cpu cpu-number ] ]
Display outbound dynamic NAT configuration.	display nat outbound
Display NAT server mappings.	display nat server
Display internal server group configuration.	display nat server-group [ group-id ]
Display NAT sessions.	display nat session [ { source-ip source-ip \| destination-ip destination-ip } * [ vpn-instance vpn -instance-name ] ] [ protocol { dccp \| icmp \| raw-ip \| sctp \| tcp \| udp \| udp-lite } ] [ chassis chassis-number slot slot-number [ cpu cpu-number ] ] [ verbose ]
Display static NAT mappings.	display nat static
Display NAT statistics.	display nat statistics [ summary ] [ chassis chassis-number slot slot-number [ cpu cpu-number ] ]
Display static outbound port block group mapping rules for NAT444.	display nat outbound port-block-group
Display NAT port block group configuration.	display nat port-block-group [ group-id ]
Display NAT port block mappings.	display nat port-block { dynamic \| static } [ chassis chassis-number slot slot-number [ cpu cpu-number ] ]
Delete NAT EIM entries.	reset nat eim [ protocol { icmp \| tcp \| udp } ] [ local-ip { local-ip } ] [ local-port local-port ] [ global-ip global-ip ] [ global-port global-port ] [ chassis chassis-number slot slot-number ]
Clear NAT sessions.	reset nat session [ protocol { tcp \| udp } ] [ chassis chassis-number slot slot-number [ cpu cpu-number ] ]

‌

NAT configuration examples

Example: Configuring outbound one-to-one static NAT

Network configuration

Configure static NAT to allow the host at 10.110.10.8/24 to access the Internet.

Figure 5 Network diagram

‌

Procedure

# Specify IP addresses for the interfaces on the router. (Details not shown.)

# Configure a QoS policy on the router to redirect traffic that needs NAT to the service card. (Details not shown.)

# Configure a one-to-one static NAT mapping between the private address 10.110.10.8 and the public address 202.38.1.100.

<Router> system-view

[Router] nat static outbound 10.110.10.8 202.38.1.100

# Enable static NAT on GigabitEthernet 1/2/0/2.

[Router] interface gigabitethernet 1/2/0/2

[Router-GigabitEthernet1/2/0/2] nat static enable

Verifying the configuration

# Verify that the host at 10.110.10.8/24 can access the server on the Internet. (Details not shown.)

# Display static NAT configuration.

[Router] display nat static

Slot 0 in chassis 1:

Static NAT mappings:

Totally 1 outbound static NAT mappings.

IP-to-IP:

Local IP : 10.110.10.8

Global IP : 202.38.1.100

Config status: Active

Interfaces enabled with static NAT:

Totally 1 interfaces enabled with static NAT.

Interface: GigabitEthernet1/2/0/2

Config status: Active

# Display NAT session information.

[Router] display nat session verbose

Slot 0 in chassis 1:

Initiator:

Source IP/port: 10.110.10.8/42496

Destination IP/port: 202.38.1.111/2048

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: ICMP(1)

Inbound interface: GigabitEthernet1/2/0/1

Responder:

Source IP/port: 202.38.1.111/42496

Destination IP/port: 202.38.1.100/0

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: ICMP(1)

Inbound interface: GigabitEthernet1/2/0/2

State: ICMP_REPLY

Application: OTHER

Role: -

Failover group ID: -

Start time: 2012-08-16 09:30:49 TTL: 27s

Initiator->Responder: 5 packets 420 bytes

Responder->Initiator: 5 packets 420 bytes

Total sessions found: 1

Example: Configuring outbound dynamic NAT (non-overlapping addresses)

Network configuration

As shown in Figure 6, a company has a private address 192.168.0.0/16 and two public IP addresses 202.38.1.2 and 202.38.1.3. Configure outbound dynamic NAT to allow only internal users on subnet 192.168.1.0/24 to access the Internet.

Figure 6 Network diagram

‌

Procedure

# Specify IP addresses for the interfaces on the router. (Details not shown.)

# Configure a QoS policy on the router to redirect traffic that needs NAT to the service card. (Details not shown.)

# Configure address group 0, and add an address range from 202.38.1.2 to 202.38.1.3 to the group.

<Router> system-view

[Router] nat address-group 0

[Router-address-group-0] address 202.38.1.2 202.38.1.3

[Router-address-group-0] quit

# Configure ACL 2000 to identify packets from subnet 192.168.1.0/24.

[Router] acl basic 2000

[Router-acl-ipv4-basic-2000] rule permit source 192.168.1.0 0.0.0.255

[Router-acl-ipv4-basic-2000] quit

# Enable outbound dynamic PAT on GigabitEthernet 1/2/0/2. The source IP addresses of the packets permitted by the ACL rule is translated into the addresses in address group 0.

[Router] interface gigabitethernet 1/2/0/2

[Router-GigabitEthernet1/2/0/2] nat outbound 2000 address-group 0

[Router-GigabitEthernet1/2/0/2] quit

Verifying the configuration

# Verify that Host A can access the WWW server, while Host B cannot. (Details not shown.)

# Display all NAT configuration and statistics.

[Router] display nat all

Slot 0 in chassis 1:

NAT address group information:

Totally 1 NAT address groups.

Address group 0:

Port range: 1-65535

Address information:

Start address End address

202.38.1.2 202.38.1.3

NAT outbound information:

Totally 1 NAT outbound rules.

Interface: GigabitEthernet1/2/0/2

ACL: 2000 Address group: 0 Port-preserved: N

NO-PAT: N Reversible: N

Config status: Active

NAT logging:

Log enable : Disabled

Flow-begin : Disabled

Flow-end : Disabled

Flow-active : Disabled

Port-block-assign : Disabled

Port-block-withdraw : Disabled

Port-alloc-fail : Enabled

Port-block-alloc-fail : Disabled

Port-usage : Disabled

Port-block-usage : Enabled(Threshold: 40%)

NAT mapping behavior:

Mapping mode : Address and Port-Dependent

ACL : ---

Config status: Active

NAT ALG:

DNS : Disabled

FTP : Enabled

H323 : Disabled

ICMP-ERROR : Enabled

ILS : Disabled

MGCP : Disabled

NBT : Disabled

PPTP : Disabled

RTSP : Enabled

RSH : Disabled

SCCP : Disabled

SIP : Disabled

SQLNET : Disabled

TFTP : Disabled

XDMCP : Disabled

# Display NAT session information generated when Host A accesses the WWW server.

[Router] display nat session verbose

Slot 0 in chassis 1:

Initiator:

Source IP/port: 192.168.1.10/52992

Destination IP/port: 200.1.1.10/2048

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: ICMP(1)

Inbound interface: GigabitEthernet1/2/0/1

Responder:

Source IP/port: 200.1.1.10/4

Destination IP/port: 202.38.1.3/0

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: ICMP(1)

Inbound interface: GigabitEthernet1/2/0/2

State: ICMP_REPLY

Application: OTHER

Role: -

Failover group ID: -

Start time: 2012-08-15 14:53:29 TTL: 12s

Initiator->Responder: 1 packets 84 bytes

Responder->Initiator: 1 packets 84 bytes

Total sessions found: 1

Example: Configuring outbound bidirectional NAT

Network configuration

As shown in Figure 7, the private network where the Web server resides overlaps with the company private network 192.168.1.0/24. The company has two public IP addresses 202.38.1.2 and 202.38.1.3. Configure NAT to allow internal users to access the external Web server by using the server's domain name.

Figure 7 Network diagram

‌

Analysis

To meet the network requirements, you must perform the following tasks:

· Configure inbound dynamic NAT ALG to make sure the internal host reaches the Web server instead of another internal host. NAT ALG can translate the Web server's IP address in the DNS reply payload to a dynamically assigned public address.

· Configure outbound dynamic NAT to translate the source IP address of packets from an internal host to a dynamically assigned public address.

· Add a static route to the public IP address of the external Web server.

Procedure

# Specify IP addresses for the interfaces on the router. (Details not shown.)

# Configure a QoS policy on the router to redirect traffic that needs NAT to the service card. (Details not shown.)

# Enable NAT ALG and DNS.

<Router> system-view

[Router] nat alg dns

# Configure ACL 2000 to identify packets from subnet 192.168.1.0/24.

[Router] acl basic 2000

[Router-acl-ipv4-basic-2000] rule permit source 192.168.1.0 0.0.0.255

[Router-acl-ipv4-basic-2000] quit

# Create address group 1.

[Router] nat address-group 1

# Add address 202.38.1.2 to the group.

[Router-address-group-1] address 202.38.1.2 202.38.1.2

[Router-address-group-1] quit

# Create address group 2.

[Router] nat address-group 2

# Add address 202.38.1.3 to the group.

[Router-address-group-2] address 202.38.1.3 202.38.1.3

[Router-address-group-2] quit

# Enable inbound NO-PAT on GigabitEthernet 1/2/0/2 to translate the source IP address in the DNS reply payload into the address in address group 1, and allow reversible NAT.

[Router] interface gigabitethernet 1/2/0/2

[Router-GigabitEthernet1/2/0/2] nat inbound 2000 address-group 1 no-pat reversible

# Enable outbound PAT on GigabitEthernet 1/2/0/2 to translate the source address of outgoing packets into the address in address group 2.

[Router-GigabitEthernet1/2/0/2] nat outbound 2000 address-group 2

# Configure a static route to 202.38.1.2 with GigabitEthernet 1/2/0/2 as the output interface and 20.2.2.2 as the next hop. (The next hop address varies by network.)

[Router] ip route-static 202.38.1.2 32 gigabitethernet 1/2/0/2 20.2.2.2

Verifying the configuration

# Verify that Host A can access the Web server by using its domain name. (Details not shown.)

# Display all NAT configuration and statistics.

[Router] display nat all

Slot 0 in chassis 1:

NAT address group information:

Totally 2 NAT address groups.

Address group 1:

Port range: 1-65535

Address information:

Start address End address

202.38.1.2 202.38.1.2

Address group 2:

Port range: 1-65535

Address information:

Start address End address

202.38.1.3 202.38.1.3

NAT inbound information:

Totally 1 NAT inbound rules.

Interface: GigabitEthernet1/2/0/2

ACL: 2000 Address group: 1 Add route: N

NO-PAT: Y Reversible: Y

Config status: Active

NAT outbound information:

Totally 1 NAT outbound rules.

Interface: GigabitEthernet1/2/0/2

ACL: 2000 Address group: 2 Port-preserved: N

NO-PAT: N Reversible: N

Config status: Active

NAT logging:

Log enable : Disabled

Flow-begin : Disabled

Flow-end : Disabled

Flow-active : Disabled

Port-block-assign : Disabled

Port-block-withdraw : Disabled

Port-alloc-fail : Enabled

Port-block-alloc-fail : Disabled

Port-usage : Disabled

Port-block-usage : Enabled(Threshold: 40%)

NAT mapping behavior:

Mapping mode : Address and Port-Dependent

ACL : ---

Config status: Active

NAT ALG:

DNS : Enabled

FTP : Enabled

H323 : Disabled

ICMP-ERROR : Enabled

ILS : Disabled

MGCP : Disabled

NBT : Disabled

PPTP : Disabled

RTSP : Enabled

RSH : Disabled

SCCP : Disabled

SIP : Disabled

SQLNET : Disabled

TFTP : Disabled

XDMCP : Disabled

# Display NAT session information generated when Host A accesses the Web server.

[Router] display nat session verbose

Slot 0 in chassis 1:

Initiator:

Source IP/port: 192.168.1.10/1694

Destination IP/port: 202.38.1.2/8080

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: TCP(6)

Inbound interface: GigabitEthernet1/2/0/1

Responder:

Source IP/port: 192.168.1.10/8080

Destination IP/port: 202.38.1.3/1025

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: TCP(6)

Inbound interface: GigabitEthernet1/2/0/2

State: TCP_ESTABLISHED

Role: -

Failover group ID: -

Application: HTTP

Start time: 2012-08-15 14:53:29 TTL: 3597s

Initiator->Responder: 7 packets 308 bytes

Responder->Initiator: 5 packets 312 bytes

Total sessions found: 1

Example: Configuring NAT Server for external-to-internal access

Network configuration

As shown in Figure 8, two Web servers, one FTP server and one SMTP server are in the internal network to provide services for external users. The internal network address is 10.110.0.0/16. The company has three public IP addresses from 202.38.1.1/24 to 202.38.1.3/24.

Configure the NAT Server feature to allow the external user to use public address 202.38.1.1/24 to access the internal servers.

Figure 8 Network diagram

‌

Procedure

# Specify IP addresses for the interfaces on the router. (Details not shown.)

# Configure a QoS policy on the router to redirect traffic that needs NAT to the service card. (Details not shown.)

# Enter interface view of GigabitEthernet 1/2/0/2.

<Router> system-view

[Router] interface gigabitethernet 1/2/0/2

# Configure a NAT server mapping to allow external users to access the FTP server by using the address 202.38.1.1 and port 21.

[Router-GigabitEthernet1/2/0/2] nat server protocol tcp global 202.38.1.1 21 inside 10.110.10.3 ftp

# Configure a NAT server mapping to allow external users to access the Web server 1 by using the address 202.38.1.1 and port 80.

[Router-GigabitEthernet1/2/0/2] nat server protocol tcp global 202.38.1.1 80 inside 10.110.10.1 http

# Configure a NAT server mapping to allow external users to access the Web server 2 by using the address 202.38.1.1 and port 8080.

[Router-GigabitEthernet1/2/0/2] nat server protocol tcp global 202.38.1.1 8080 inside 10.110.10.2 http

# Configure a NAT server mapping to allow external users to access the SMTP server by using the address 202.38.1.1 and port number defined by SMTP.

[Router-GigabitEthernet1/2/0/2] nat server protocol tcp global 202.38.1.1 smtp inside 10.110.10.4 smtp

[Router-GigabitEthernet1/2/0/2] quit

Verifying the configuration

# Verify that the host on the external network can access the internal servers by using the public addresses. (Details not shown.)

# Display all NAT configuration and statistics.

[Router] display nat all

Slot 0 in chassis 1:

NAT internal server information:

Totally 4 internal servers.

Interface: GigabitEthernet1/2/0/2

Protocol: 6(TCP)

Global IP/port: 202.38.1.1/21

Local IP/port : 10.110.10.3/21

Config status : Active

Interface: GigabitEthernet1/2/0/2

Protocol: 6(TCP)

Global IP/port: 202.38.1.1/25

Local IP/port : 10.110.10.4/25

Config status : Active

Interface: GigabitEthernet1/2/0/2

Protocol: 6(TCP)

Global IP/port: 202.38.1.1/80

Local IP/port : 10.110.10.1/80

Config status : Active

Interface: GigabitEthernet1/2/0/2

Protocol: 6(TCP)

Global IP/port: 202.38.1.1/8080

Local IP/port : 10.110.10.2/80

Config status : Active

NAT logging:

Log enable : Disabled

Flow-begin : Disabled

Flow-end : Disabled

Flow-active : Disabled

Port-block-assign : Disabled

Port-block-withdraw : Disabled

Port-alloc-fail : Enabled

Port-block-alloc-fail : Disabled

Port-usage : Disabled

Port-block-usage : Enabled(Threshold: 40%)

NAT mapping behavior:

Mapping mode : Address and Port-Dependent

ACL : ---

Config status: Active

NAT ALG:

DNS : Disabled

FTP : Enabled

H323 : Disabled

ICMP-ERROR : Enabled

ILS : Disabled

MGCP : Disabled

NBT : Disabled

PPTP : Disabled

RTSP : Enabled

RSH : Disabled

SCCP : Disabled

SIP : Disabled

SQLNET : Disabled

TFTP : Disabled

XDMCP : Disabled

# Display NAT session information generated when Host accesses the FTP server.

[Router] display nat session verbose

Slot 0 in chassis 1:

Initiator:

Source IP/port: 202.38.1.10/1694

Destination IP/port: 202.38.1.1/21

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: TCP(6)

Inbound interface: GigabitEthernet1/2/0/2

Responder:

Source IP/port: 10.110.10.3/21

Destination IP/port: 202.38.1.10/1694

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: TCP(6)

Inbound interface: GigabitEthernet1/2/0/1

State: TCP_ESTABLISHED

Application: FTP

Role: -

Failover group ID: -

Start time: 2012-08-15 14:53:29 TTL: 3597s

Initiator->Responder: 7 packets 308 bytes

Responder->Initiator: 5 packets 312 bytes

Total sessions found: 1

Example: Configuring NAT Server for external-to-internal access through domain name

Network configuration

As shown in Figure 9, Web server at 10.110.10.2/24 in the internal network provides services for external users. A DNS server at 10.110.10.3/24 is used to resolve the domain name of the Web server. The company has two public IP addresses: 202.38.1.2 and 202.38.1.3.

Configure NAT Server to allow external users to access the internal Web server by using the domain name.

Figure 9 Network diagram

‌

Analysis

To meet the network configuration requirements, you must perform the following tasks:

· Configure NAT Server to map the private IP address and port of the DNS server to a public address and port. NAT Server allows the external host to access the internal DNS server for domain name resolution.

· Enable ALG for DNS and configure outbound dynamic NAT to translate the private IP address of the Web server in the payload of the DNS response packet into a public IP address.

Procedure

# Specify IP addresses for the interfaces on the router. (Details not shown.)

# Configure a QoS policy on the router to redirect traffic that needs NAT to the service card. (Details not shown.)

# Enable NAT ALG for DNS.

<Router> system-view

[Router] nat alg dns

# Configure ACL 2000 to identify packets from 10.110.10.2.

[Router] acl basic 2000

[Router-acl-ipv4-basic-2000] rule permit source 10.110.10.2 0

[Router-acl-ipv4-basic-2000] quit

# Create address group 1.

[Router] nat address-group 1

# Add address 202.38.1.3 to the group.

[Router-address-group-1] address 202.38.1.3 202.38.1.3

[Router-address-group-1] quit

# Configure NAT Server on GigabitEthernet 1/2/0/2 to map the address 202.38.1.1 to 10.110.10.3. External users can access the internal DNS server.

[Router] interface gigabitethernet 1/2/0/2

[Router-GigabitEthernet1/2/0/2] nat server protocol udp global 202.38.1.2 inside 10.110.10.3 dns

# Enable outbound NO-PAT on GigabitEthernet 1/2/0/2. Use the address in address group 1 to translate the private address in DNS response payload, and allow reversible NAT.

[Router-GigabitEthernet1/2/0/2] nat outbound 2000 address-group 1 no-pat reversible

[Router-GigabitEthernet1/2/0/2] quit

Verifying the configuration

# Verify that the host on the external network can access the internal Web server by using the server's domain name. (Details not shown.)

# Display all NAT configuration and statistics.

[Router] display nat all

Slot 0 in chassis 1:

NAT address group information:

Totally 1 NAT address groups.

Address group 1:

Port range: 1-65535

Address information:

Start address End address

202.38.1.3 202.38.1.3

NAT outbound information:

Totally 1 NAT outbound rules.

Interface: GigabitEthernet1/2/0/2

ACL: 2000 Address group: 1 Port-preserved: N

NO-PAT: Y Reversible: Y

Config status: Active

NAT internal server information:

Totally 1 internal servers.

Interface: GigabitEthernet1/2/0/2

Protocol: 17(UDP)

Global IP/port: 202.38.1.2/53

Local IP/port : 10.110.10.3/53

Config status : Active

NAT logging:

Log enable : Disabled

Flow-begin : Disabled

Flow-end : Disabled

Flow-active : Disabled

Port-block-assign : Disabled

Port-block-withdraw : Disabled

Port-alloc-fail : Enabled

Port-block-alloc-fail : Disabled

Port-usage : Disabled

Port-block-usage : Enabled(Threshold: 40%)

NAT mapping behavior:

Mapping mode : Address and Port-Dependent

ACL : ---

Config status: Active

NAT ALG:

DNS : Enabled

FTP : Enabled

H323 : Disabled

ICMP-ERROR : Enabled

ILS : Disabled

MGCP : Disabled

NBT : Disabled

PPTP : Disabled

RTSP : Enabled

RSH : Disabled

SCCP : Disabled

SIP : Disabled

SQLNET : Disabled

TFTP : Disabled

XDMCP : Disabled

# Display NAT session information generated when Host accesses Web server.

[Router] display nat session verbose

Slot 0 in chassis 1:

Initiator:

Source IP/port: 200.1.1.2/1694

Destination IP/port: 202.38.1.3/8080

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: TCP(6)

Inbound interface: GigabitEthernet1/2/0/2

Responder:

Source IP/port: 10.110.10.2/8080

Destination IP/port: 202.1.1.2/1694

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: TCP(6)

Inbound interface: GigabitEthernet1/2/0/1

State: TCP_ESTABLISHED

Application: HTTP

Role: -

Failover group ID: -

Start time: 2012-08-15 14:53:29 TTL: 3597s

Initiator->Responder: 7 packets 308 bytes

Responder->Initiator: 5 packets 312 bytes

Total sessions found: 1

Example: Configuring NAT hairpin in C/S mode

Network configuration

As shown in Figure 10, the internal FTP server at 192.168.1.4/24 provides services for internal and external users. The private network uses two public IP addresses 202.38.1.1 and 202.38.1.2.

Configure NAT hairpin in C/S mode to allow external and internal users to access the internal FTP server by using public IP address 202.38.1.2.

Figure 10 Network diagram

‌

Requirements analysis

To allow external hosts to access the internal FTP server by using a public IP address, configure NAT Server on the interface connected to the external network.

To allow internal hosts to access the internal FTP server by using a public IP address, perform the following tasks:

· Enable NAT hairpin on the interface connected to the internal network.

· Configure outbound NAT on the interface where the NAT server mapping is configured. The destination address is translated by matching the NAT server mapping. The source address is translated by matching the outbound NAT.

Procedure

# Specify IP addresses for the interfaces on the router. (Details not shown.)

# Configure a QoS policy on the router to redirect traffic that needs NAT to the service card. (Details not shown.)

# Configure ACL 2000 to identify packets from subnet 192.168.1.0/24.

<Router> system-view

[Router] acl basic 2000

[Router-acl-ipv4-basic-2000] rule permit source 192.168.1.0 0.0.0.255

[Router-acl-ipv4-basic-2000] quit

# Configure a NAT server mapping on GigabitEthernet 1/2/0/2 to map the IP address of the FTP server to a public address, allowing external users to access the internal FTP server.

[Router] interface gigabitethernet 1/2/0/2

[Router-GigabitEthernet1/2/0/2] nat server protocol tcp global 202.38.1.2 inside 192.168.1.4 ftp

# Enable outbound NAT with Easy IP on GigabitEthernet 1/2/0/2 so that NAT translates the source addresses of the packets from internal hosts into the IP address of GigabitEthernet 1/2/0/2.

[Router-GigabitEthernet1/2/0/2] nat outbound 2000

# Enable NAT hairpin on GigabitEthernet 1/2/0/1.

[Router] interface gigabitethernet 1/2/0/1

[Router-GigabitEthernet1/2/0/1] nat hairpin enable

[Router-GigabitEthernet1/2/0/1] quit

Verifying the configuration

# Verify that both internal and external hosts can access the internal FTP server through the public address. (Details not shown.)

# Display all NAT configuration and statistics.

[Router]display nat all

Slot 0 in chassis 1:

NAT outbound information:

Totally 1 NAT outbound rules.

Interface: GigabitEthernet1/2/0/2

ACL: 2000 Address group: --- Port-preserved: N

NO-PAT: N Reversible: N

Config status: Active

NAT internal server information:

Totally 1 internal servers.

Interface: GigabitEthernet1/2/0/2

Protocol: 6(TCP)

Global IP/port: 202.38.1.2/21

Local IP/port : 192.168.1.4/21

Config status : Active

NAT logging:

Log enable : Disabled

Flow-begin : Disabled

Flow-end : Disabled

Flow-active : Disabled

Port-block-assign : Disabled

Port-block-withdraw : Disabled

Port-alloc-fail : Enabled

Port-block-alloc-fail : Disabled

Port-usage : Disabled

Port-block-usage : Enabled(Threshold: 40%)

NAT hairpinning:

Totally 1 interfaces enabled with NAT hairpinning.

Interface: GigabitEthernet1/2/0/1

Config status: Active

NAT mapping behavior:

Mapping mode : Address and Port-Dependent

ACL : ---

Config status: Active

NAT ALG:

DNS : Disabled

FTP : Enabled

H323 : Disabled

ICMP-ERROR : Enabled

ILS : Disabled

MGCP : Disabled

NBT : Disabled

PPTP : Disabled

RTSP : Enabled

RSH : Disabled

SCCP : Disabled

SIP : Disabled

SQLNET : Disabled

TFTP : Disabled

XDMCP : Disabled

# Display NAT session information generated when Host A accesses the FTP server.

[Router] display nat session verbose

Slot 0 in chassis 1:

Initiator:

Source IP/port: 192.168.1.2/1694

Destination IP/port: 202.38.1.2/21

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: TCP(6)

Inbound interface: GigabitEthernet1/2/0/1

Responder:

Source IP/port: 192.168.1.4/21

Destination IP/port: 202.38.1.1/1025

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: TCP(6)

Inbound interface: GigabitEthernet1/2/0/1

State: TCP_ESTABLISHED

Application: FTP

Role: -

Failover group ID: -

Start time: 2012-08-15 14:53:29 TTL: 3597s

Initiator->Responder: 7 packets 308 bytes

Responder->Initiator: 5 packets 312 bytes

Total sessions found: 1

Example: Configuring NAT hairpin in P2P mode

Network configuration

In the P2P application, internal clients must register their IP address to the external server and the server records the registered IP addresses and port numbers of the internal clients. An internal client must request the IP address and port number of another client from the external server before accessing the client.

Configure NAT hairpin so that:

· The internal clients can register the same public address to the external server.

· The internal clients can access each other through the IP address and port number obtained from the server.

Figure 11 Network diagram

‌

Requirements analysis

To meet the network requirements, you must perform the following tasks:

· Configure outbound dynamic PAT on the interface connected to the external network, so the internal clients can access the external server for registration.

· Configure the mapping behavior for PAT as Endpoint-Independent Mapping because the registered IP address and port number should be accessible for any source address.

· Enable NAT hairpin on the interface connected to the internal network so that internal clients can access each other through the public address.

Procedure

# Specify IP addresses for the interfaces on the router. (Details not shown.)

# Configure a QoS policy on the router to redirect traffic that needs NAT to the service card. (Details not shown.)

# Configure ACL 2000 to identify packets from subnet 192.168.1.0/24.

<Router> system-view

[Router] acl basic 2000

[Router-acl-ipv4-basic-2000] rule permit source 192.168.1.0 0.0.0.255

[Router-acl-ipv4-basic-2000] quit

# Configure outbound dynamic PAT with Easy IP on GigabitEthernet 1/2/0/2. The IP address of GigabitEthernet 1/2/0/2 is used as the public address for the source address translation of the packets from internal to external.

[Router] interface gigabitethernet 1/2/0/2

[Router-GigabitEthernet1/2/0/2] nat outbound 2000

# Configure the Endpoint-Independent Mapping mode for PAT. For packets with the same source address and port number and permitted by ACL 2000, the source address and port number are translated to the same public address and port number.

[Router] nat mapping-behavior endpoint-independent acl 2000

# Enable NAT hairpin on GigabitEthernet 1/2/0/1.

[Router] interface gigabitethernet 1/2/0/1

[Router-GigabitEthernet1/2/0/1] nat hairpin enable

[Router-GigabitEthernet1/2/0/1] quit

Verifying the configuration

# Verify that Host A, Host B, and Host C can access each other after they register their IP addresses and port numbers to the external server. (Details not shown.)

# Display all NAT configuration and statistics.

[Router] display nat all

Slot 0 in chassis 1:

NAT outbound information:

Totally 1 NAT outbound rules.

Interface: GigabitEthernet1/2/0/2

ACL: 2000 Address group: --- Port-preserved: N

NO-PAT: N Reversible: N

Config status: Active

NAT logging:

Log enable : Disabled

Flow-begin : Disabled

Flow-end : Disabled

Flow-active : Disabled

Port-block-assign : Disabled

Port-block-withdraw : Disabled

Port-alloc-fail : Enabled

Port-block-alloc-fail : Disabled

Port-usage : Disabled

Port-block-usage : Enabled(Threshold: 40%)

NAT hairpinning:

Totally 1 interfaces enabled with NAT hairpinning.

Interface: GigabitEthernet1/2/0/1

Config status: Active

NAT mapping behavior:

Mapping mode : Endpoint-Independent

ACL : 2000

Config status: Active

NAT ALG:

DNS : Disabled

FTP : Enabled

H323 : Disabled

ICMP-ERROR : Enabled

ILS : Disabled

MGCP : Disabled

NBT : Disabled

PPTP : Disabled

RTSP : Enabled

RSH : Disabled

SCCP : Disabled

SIP : Disabled

SQLNET : Disabled

TFTP : Disabled

XDMCP : Disabled

# Display NAT sessions that are generated when Client A accesses Client B.

[Router] display nat session verbose

Slot 0 in chassis 1:

Initiator:

Source IP/port: 192.168.1.3/44929

Destination IP/port: 202.38.1.3/1

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: UDP(17)

Inbound interface: GigabitEthernet1/2/0/1

Responder:

Source IP/port: 192.168.1.2/69

Destination IP/port: 202.38.1.3/1024

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: UDP(17)

Inbound interface: GigabitEthernet1/2/0/1

State: UDP_READY

Application: TFTP

Role: -

Failover group ID: -

Start time: 2012-08-15 15:53:36 TTL: 46s

Initiator->Responder: 1 packets 56 bytes

Responder->Initiator: 1 packets 72 bytes

Total sessions found: 1

Example: Configuring Twice NAT

Network configuration

As shown in Figure 12, two departments are in different VPN instances with overlapping addresses. Configure twice NAT so that Host A and Host B in different departments can access each other.

Figure 12 Network diagram

‌

Requirements analysis

This is a typical application of twice NAT. Both the source and destination addresses of packets between the two VPNs need to be translated. Configure static NAT on both interfaces connected to the VPNs on the NAT device.

Procedure

# Specify VPN instances and IP addresses for the interfaces on the router. (Details not shown.)

# Configure a QoS policy on the router to redirect traffic that needs NAT to the service card. (Details not shown.)

# Configure a static outbound NAT mapping between 192.168.1.2 in vpn 1 and 172.16.1.2 in vpn 2.

<Router> system-view

[Router] nat static outbound 192.168.1.2 vpn-instance vpn1 172.16.1.2 vpn-instance vpn2

# Configure a static outbound NAT mapping between 192.168.1.2 in vpn 2 and 172.16.2.2 in vpn 1.

[Router] nat static outbound 192.168.1.2 vpn-instance vpn2 172.16.2.2 vpn-instance vpn1

# Enable static NAT on GigabitEthernet 1/2/0/2.

[Router] interface gigabitethernet 1/2/0/2

[Router-GigabitEthernet1/2/0/2] nat static enable

# Enable static NAT on GigabitEthernet 1/2/0/1.

[Router] interface gigabitethernet 1/2/0/1

[Router-GigabitEthernet1/2/0/1] nat static enable

[Router-GigabitEthernet1/2/0/1] quit

Verifying the configuration

# Verify that Host A and Host B can access each other. The public address for Host A is 172.16.1.2 and that for Host B is 172.16.2.2. (Details not shown.)

# Display all NAT configuration and statistics.

[Router] display nat all

Slot 0 in chassis 1:

Static NAT mappings:

Totally 2 outbound static NAT mappings.

IP-to-IP:

Local IP : 192.168.1.2

Global IP : 172.16.1.2

Local VPN : vpn1

Global VPN : vpn2

Config status: Active

IP-to-IP:

Local IP : 192.168.1.2

Global IP : 172.16.2.2

Local VPN : vpn2

Global VPN : vpn1

Config status: Active

Interfaces enabled with static NAT:

Totally 2 interfaces enabled with static NAT.

Interface: GigabitEthernet1/2/0/1

Config status: Active

Interface: GigabitEthernet1/2/0/2

Config status: Active

NAT logging:

Log enable : Disabled

Flow-begin : Disabled

Flow-end : Disabled

Flow-active : Disabled

Port-block-assign : Disabled

Port-block-withdraw : Disabled

Port-alloc-fail : Enabled

Port-block-alloc-fail : Disabled

Port-usage : Disabled

Port-block-usage : Enabled(Threshold: 40%)

NAT mapping behavior:

Mapping mode : Address and Port-Dependent

ACL : ---

Config status: Active

NAT ALG:

DNS : Disabled

FTP : Enabled

H323 : Disabled

ICMP-ERROR : Enabled

ILS : Disabled

MGCP : Disabled

NBT : Disabled

PPTP : Disabled

RTSP : Enabled

RSH : Disabled

SCCP : Disabled

SIP : Disabled

SQLNET : Disabled

TFTP : Disabled

XDMCP : Disabled

# Display NAT session information generated when Host A accesses Host B.

[Router] display nat session verbose

Slot 0 in chassis 1:

Initiator:

Source IP/port: 192.168.1.2/42496

Destination IP/port: 172.16.2.2/2048

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: vpn1/-/-

Protocol: ICMP(1)

Inbound interface: GigabitEthernet1/2/0/1

Responder:

Source IP/port: 192.168.1.2/42496

Destination IP/port: 172.16.1.2/0

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: vpn2/-/-

Protocol: ICMP(1)

Inbound interface: GigabitEthernet1/2/0/2

State: ICMP_REPLY

Application: OTHER

Role: -

Failover group ID: -

Start time: 2012-08-16 09:30:49 TTL: 27s

Initiator->Responder: 5 packets 420 bytes

Responder->Initiator: 5 packets 420 bytes

Total sessions found: 1

Example: Configuring load sharing NAT Server

Network configuration

As shown in Figure 13, three FTP servers are in the intranet to provide FTP services for external users. Configure NAT so that these external users use the address 202.38.1.1/16 to access the servers and the three FTP servers implement load sharing.

Figure 13 Network diagram

‌

Procedure

# Specify IP addresses for the interfaces on the router. (Details not shown.)

# Configure a QoS policy on the router to redirect traffic that needs NAT to the service card. (Details not shown.)

# Create NAT Server group 0, and add members to the group.

<Router> system-view

[Router] nat server-group 0

[Router-nat-server-group-0] inside ip 10.110.10.1 port 21

[Router-nat-server-group-0] inside ip 10.110.10.2 port 21

[Router-nat-server-group-0] inside ip 10.110.10.3 port 21

[Router-nat-server-group-0] quit

# Associate NAT Server group 0 with GigabitEthernet 1/2/0/2 so that servers in the server group can provide FTP services.

[Router] interface gigabitethernet 1/2/0/2

[Router-GigabitEthernet1/2/0/2] nat server protocol tcp global 202.38.1.1 ftp inside server-group 0

[Router-GigabitEthernet1/2/0/2] quit

Verifying the configuration

# Verify that external hosts can access the internal FTP server group. (Details not shown.)

# Display all NAT configuration and statistics.

[Router] display nat all

Slot 0 in chassis 1:

NAT server group information:

Totally 1 NAT server groups.

Group Number Inside IP Port Weight

0 10.110.10.1 21 100

10.110.10.2 21 100

10.110.10.3 21 100

NAT internal server information:

Totally 1 internal servers.

Interface: GigabitEthernet1/2/0/2

Protocol: 6(TCP)

Global IP/port: 202.38.1.1/21

Local IP/port : server group 0

10.110.10.1/21 (Connections: 1)

10.110.10.2/21 (Connections: 2)

10.110.10.3/21 (Connections: 2)

Config status : Active

NAT logging:

Log enable : Disabled

Flow-begin : Disabled

Flow-end : Disabled

Flow-active : Disabled

Port-block-assign : Disabled

Port-block-withdraw : Disabled

Port-alloc-fail : Enabled

Port-block-alloc-fail : Disabled

Port-usage : Disabled

Port-block-usage : Enabled(Threshold: 40%)

NAT mapping behavior:

Mapping mode : Address and Port-Dependent

ACL : ---

Config status: Active

NAT ALG:

DNS : Disabled

FTP : Enabled

H323 : Disabled

ICMP-ERROR : Enabled

ILS : Disabled

MGCP : Disabled

NBT : Disabled

PPTP : Disabled

RTSP : Enabled

RSH : Disabled

SCCP : Disabled

SIP : Disabled

SQLNET : Disabled

TFTP : Disabled

XDMCP : Disabled

# Display NAT session information generated when external hosts access an internal FTP server.

[Router] display nat session verbose

Slot 0 in chassis 1:

Initiator:

Source IP/port: 202.38.1.25/53957

Destination IP/port: 202.38.1.1/21

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: TCP(6)

Inbound interface: GigabitEthernet1/2/0/2

Responder:

Source IP/port: 10.110.10.3/21

Destination IP/port: 202.38.1.25/53957

DS-Lite tunnel peer: -

VPN instance/VLAN ID/VLL ID: -/-/-

Protocol: TCP(6)

Inbound interface: GigabitEthernet1/2/0/1

State: TCP_ESTABLISHED

Application: FTP

Role: -

Failover group ID: -

Start time: 2012-08-16 11:06:07 TTL: 26s

Initiator->Responder: 1 packets 60 bytes

Responder->Initiator: 2 packets 120 bytes

Total sessions found: 1

Example: Configuring NAT DNS mapping

Network configuration

As shown in Figure 14, the internal Web server at 10.110.10.1/16 and FTP server at 10.110.10.2/16 provide services for external user. The company has three public addresses 202.38.1.1 through 202.38.1.3. The DNS server at 202.38.1.4 is on the external network.

Configure NAT so that:

· The public IP address 202.38.1.2 is used by external users to access the Web and FTP servers.

· External users can use the public address or domain name of internal servers to access them.

· Internal users can access the internal servers by using their domain names.

Figure 14 Network diagram

‌

Requirements analysis

To meet the network requirements, perform the following tasks:

· Configure NAT Server by mapping the public IP addresses and port numbers of the internal servers to a public address and port numbers so that external users can access the internal servers.

· Configure NAT DNS mapping and ALG so that the public IP address of the internal server in the payload of the DNS response packet can be translated to the private IP address.

Procedure

# Specify IP addresses for the interfaces on the router. (Details not shown.)

# Configure a QoS policy on the router to redirect traffic that needs NAT to the service card. (Details not shown.)

# Enable NAT ALG for DNS.

<Router> system-view

[Router] nat alg dns

# Enter interface view of GigabitEthernet 1/2/0/2.

[Router] interface gigabitethernet 1/2/0/2

# Configure NAT Server to allow external hosts to access the internal Web server by using the address 202.38.1.2.

[Router-GigabitEthernet1/2/0/2] nat server protocol tcp global 202.38.1.2 inside 10.110.10.1 http

# Configure NAT Server to allow external hosts to access the internal FTP server by using the address 202.38.1.2.

[Router-GigabitEthernet1/2/0/2] nat server protocol tcp global 202.38.1.2 inside 10.110.10.2 ftp

# Enable outbound NAT with Easy IP on GigabitEthernet 1/2/0/2.

[Router-GigabitEthernet1/2/0/2] nat outbound

# Configure two NAT DNS mapping entries by mapping the domain name www.server.com of the Web server to 202.38.1.2, and ftp.server.com of the FTP server to 202.38.1.2.

[Router] nat dns-map domain www.server.com protocol tcp ip 202.38.1.2 port http

[Router] nat dns-map domain ftp.server.com protocol tcp ip 202.38.1.2 port ftp

[Router] quit

Verifying the configuration

# Verify that both internal and external hosts can access the internal servers by using domain names. (Details not shown.)

# Display all NAT configuration and statistics.

[Router] display nat all

Slot 0 in chassis 1:

NAT outbound information:

Totally 1 NAT outbound rules.

Interface: GigabitEthernet1/2/0/2

ACL: --- Address group: --- Port-preserved: N

NO-PAT: N Reversible: N

Config status: Active

NAT internal server information:

Totally 2 internal servers.

Interface: GigabitEthernet1/2/0/2

Protocol: 6(TCP)

Global IP/port: 202.38.1.2/21

Local IP/port : 10.110.10.2/21

Config status : Active

Interface: GigabitEthernet1/2/0/2

Protocol: 6(TCP)

Global IP/port: 202.38.1.2/80

Local IP/port : 10.110.10.1/80

Config status : Active

NAT DNS mapping information:

Totally 2 NAT DNS mappings.

Domain name: ftp.server.com

Global IP : 202.38.1.2

Global port: 21

Protocol : TCP(6)

Config status: Active

Domain name: www.server.com

Global IP : 202.38.1.2

Global port: 80

Protocol : TCP(6)

Config status: Active

NAT logging:

Log enable : Disabled

Flow-begin : Disabled

Flow-end : Disabled

Flow-active : Disabled

Port-block-assign : Disabled

Port-block-withdraw : Disabled

Port-alloc-fail : Enabled

Port-block-alloc-fail : Disabled

Port-usage : Disabled

Port-block-usage : Enabled(Threshold: 40%)

NAT mapping behavior:

Mapping mode: Address and Port-Dependent

ACL : ---

Config status: Active

NAT ALG:

DNS : Enabled

FTP : Enabled

H323 : Disabled

ICMP-ERROR : Enabled

ILS : Disabled

MGCP : Disabled

NBT : Disabled

PPTP : Disabled

RTSP : Enabled

RSH : Disabled

SCCP : Disabled

SIP : Disabled

SQLNET : Disabled

TFTP : Disabled

XDMCP : Disabled

Example: Configuring NAT static port block mapping

Network configuration

As shown in Figure 15, configure NAT static port block mapping to allow users at private IP addresses 10.110.10.1 to 10.110.10.10 to use public IP address 202.38.1.100 for accessing the Internet. Configure the port range as 10001 to 15000, and set the port block size to 500.

Figure 15 Network diagram

‌

Procedure

# Specify IP addresses for the interfaces on the router. (Details not shown.)

# Configure a QoS policy on the router to redirect traffic that needs NAT to the service card. (Details not shown.)

# Create NAT port block group 1.

<Router> system-view

[Router] nat port-block-group 1

# Add the private IP addresses from 10.110.10.1 to 10.110.10.10 to the port block group.

[Router-port-block-group-1] local-ip-address 10.110.10.1 10.110.10.10

# Add the public IP address 202.38.1.100 to the port block group.

[Router-port-block-group-1] global-ip-pool 202.38.1.100 202.38.1.100

# Set the port block size to 500.

[Router-port-block-group-1] block-size 500

# Configure the port range as 10001 to 15000.

[Router-port-block-group-1] port-range 10001 15000

[Router-port-block-group-1] quit

# Apply the port block group 1 to the outbound direction of GigabitEthernet 1/2/0/2.

[Router] interface gigabitethernet 1/2/0/2

[Router-GigabitEthernet1/2/0/2] nat outbound port-block-group 1

[Router-GigabitEthernet1/2/0/2] quit

# Enable flow-triggered port block assignment.

[Router] nat port-block flow-trigger enable

Verifying the configuration

# Verify that users at the private IP addresses can access the Internet. (Details not shown.)

# Display all NAT configuration and statistics.

[Router] display nat all

Slot 0 in chassis 1:

NAT logging:

Log enable : Disabled

Flow-begin : Disabled

Flow-end : Disabled

Flow-active : Disabled

Port-block-assign : Disabled

Port-block-withdraw : Disabled

Port-alloc-fail : Enabled

Port-block-alloc-fail : Disabled

Port-usage : Disabled

Port-block-usage : Enabled(Threshold: 40%)

NAT mapping behavior:

Mapping mode : Address and Port-Dependent

ACL : ---

Config status: Active

NAT ALG:

DNS : Disabled

FTP : Enabled

H323 : Disabled

ICMP-ERROR : Enabled

ILS : Disabled

MGCP : Disabled

NBT : Disabled

PPTP : Disabled

RTSP : Enabled

RSH : Disabled

SCCP : Disabled

SIP : Disabled

SQLNET : Disabled

TFTP : Disabled

XDMCP : Disabled

NAT port block group information:

Totally 1 NAT port block groups.

Port block group 1:

Port range: 10001-15000

Block size: 500

Local IP address information:

Start address End address VPN instance

10.110.10.1 10.110.10.10 ---

Global IP pool information:

Start address End address

202.38.1.100 202.38.1.100

NAT outbound port block group information:

Totally 1 outbound port block group items.

Interface: GigabitEthernet1/2/0/2

Port-block-group: 1

Config status : Active

# Display NAT444 static port block mappings.

[Router] display nat port-block static

Slot 0 in chassis 1:

Local VPN Local IP Global IP Port block Connections

--- 10.110.10.1 202.38.1.100 10001-10500 2

--- 10.110.10.2 202.38.1.100 10501-11000 0

--- 10.110.10.3 202.38.1.100 11001-11500 0

--- 10.110.10.4 202.38.1.100 11501-12000 0

--- 10.110.10.5 202.38.1.100 12001-12500 1

--- 10.110.10.6 202.38.1.100 12501-13000 0

--- 10.110.10.7 202.38.1.100 13001-13500 0

--- 10.110.10.8 202.38.1.100 13501-14000 0

--- 10.110.10.9 202.38.1.100 14001-14500 0

--- 10.110.10.10 202.38.1.100 14501-15000 0

Example: Configuring NAT dynamic port block mapping

Network configuration

As shown in Figure 16, a company uses private IP address on network 192.168.0.0/16 and public IP addresses 202.38.1.2 and 202.38.1.3. Configure NAT dynamic port block mapping to meet the following requirements:

· Only users on subnet 192.168.1.0/24 can use public IP addresses 202.38.1.2 and 202.38.1.3 to access the Internet.

· The port range for the public IP addresses is 1024 to 65535.

· The port block size is 300.

· If the ports in the assigned port block are all used, extend another port block for users.

Figure 16 Network diagram

‌

Procedure

# Specify IP addresses for the interfaces on the router. (Details not shown.)

# Configure a QoS policy on the router to redirect traffic that needs NAT to the service card. (Details not shown.)

# Create public address group 0.

<Router> system-view

[Router] nat address-group 0

# Add public IP addresses 202.38.1.2 and 202.38.1.3 to the NAT address group.

[Router-address-group-0] address 202.38.1.2 202.38.1.3

# Configure the port range as 1024 to 65535.

[Router-address-group-0] port-range 1024 65535

# Set the port block size to 300 and the extended port block number to 1.

[Router-address-group-0] port-block block-size 300 extended-block-number 1

[Router-address-group-0] quit

# Configure an ACL to identify packets from subnet 192.168.1.0/24.

[Router] acl basic 2000

[Router-acl-ipv4-basic-2000] rule permit source 192.168.1.0 0.0.0.255

[Router-acl-ipv4-basic-2000] quit

# Configure outbound NAT on GigabitEthernet 1/2/0/2.

[Router] interface gigabitethernet 1/2/0/2

[Router-GigabitEthernet1/2/0/2] nat outbound 2000 address-group 0

[Router-GigabitEthernet1/2/0/2] quit

# Enable flow-triggered port block assignment.

[Router] nat port-block flow-trigger enable

Verifying the configuration

# Verify that Host A can access external servers, but Host B and Host C cannot. (Details not shown.)

# Display all NAT configuration and statistics.

[Router] display nat all

Slot 0 in chassis 1:

NAT address group information:

Totally 1 NAT address groups.

Address group 0:

Port range: 1024-65535

Port block size: 300

Extended block number: 1

Address information:

Start address End address

202.38.1.2 202.38.1.3

NAT outbound information:

Totally 1 NAT outbound rules.

Interface: GigabitEthernet1/2/0/2

ACL: 2000 Address group: 0 Port-preserved: N

NO-PAT: N Reversible: N

Config status: Active

NAT logging:

Log enable : Disabled

Flow-begin : Disabled

Flow-end : Disabled

Flow-active : Disabled

Port-block-assign : Disabled

Port-block-withdraw : Disabled

Port-alloc-fail : Enabled

Port-block-alloc-fail : Disabled

Port-usage : Disabled

Port-block-usage : Enabled(Threshold: 40%)

NAT mapping behavior:

Mapping mode : Address and Port-Dependent

ACL : ---

Config status: Active

NAT ALG:

DNS : Disabled

FTP : Enabled

H323 : Disabled

ICMP-ERROR : Enabled

ILS : Disabled

MGCP : Disabled

NBT : Disabled

PPTP : Disabled

RTSP : Enabled

RSH : Disabled

SCCP : Disabled

SIP : Disabled

SQLNET : Disabled

TFTP : Disabled

XDMCP : Disabled

# Display NAT statistics.

[Router] display nat statistics

Slot 1:

Total session entries: 0

Total EIM entries: 0

Total inbound NO-PAT entries: 0

Total outbound NO-PAT entries: 0

Total static port block entries: 0

Total dynamic port block entries: 430

Active static port block entries: 0

Active dynamic port block entries: 1

Example: Configuring NAT log export to the information center

Network configuration

As shown in Figure 17, configure NAT on the device for the internal host to access the Internet. Configure NAT logging on the device and configure the device to export the NAT logs to the information center. The NAT logs in the information center are used for monitoring the internal host.

Figure 17 Network diagram

Prerequisites

Assign IP addresses to interfaces on the device and make sure the device and the host can reach each other.

Procedure

# Specify the information center as the destination for flow log export.

<Device> system-view

[Device] userlog flow syslog

# Enable NAT logging.

[Device] nat log enable

# Enable logging for NAT session establishment events.

[Device] nat log flow-begin

# Enable logging for NAT session removal events.

[Device] nat log flow-end

# Enable logging for active NAT flows and set the logging interval to 10 minutes.

[Device] nat log flow-active 10

[Device] quit

Verifying the configuration

# Display the internal host's access records in the log buffer.

<Device> dir

Directory of cf:/

38 -rw- 141 Aug 07 2015 17:54:43 ifindex.dat

39 drw- - Aug 18 2014 17:51:38 license

40 drw- - May 20 2015 14:36:20 logfile

249852 KB total (232072 KB free)

File system type of cf: FAT32

<Device> cd logfile

<Device> dir

<Device> more logfile.log

…

%Jan 31 14:20:29:856 2020 Admin NAT/6/NAT_FLOW: -MDC=1-Chassis=1-Slot=7; Protoco

l(1001)=UDP;Application(1002)=http;SrcIPAddr(1003)=192.168.1.9;SrcPort(1004)=808

0;NatSrcIPAddr(1005)=104.3.1.4;NatSrcPort(1006)=13501;DstIPAddr(1007)=1.1.0.2;Ds

tPort(1008)=80;NatDstIPAddr(1009)=1.1.0.2;NatDstPort(1010)=80;InitPktCount(1044)

=1;InitByteCount(1046)=1262;RplyPktCount(1045)=0;RplyByteCount(1047)=0;RcvVPNIns

tance(1042)=;SndVPNInstance(1043)=;RcvDSLiteTunnelPeer(1040)=;SndDSLiteTunnelPee

r(1041)=;BeginTime_e(1013)=01312020142029;EndTime_e(1014)=;Event(1048)=(8)Sessio

n created;

…

Table 1 Command output

Field	Description
Protocol(1001)=ICMP	Protocol type.
SrcIPAddr(1003)=10.110.10.8	Source IP address before NAT.
SrcPort(1004)=259	Source TCP or UDP port before NAT.
NatSrcIPAddr(1005)=202.38.1.100	Source IP address after NAT.
NatSrcPort(1006)=0	Source TCP or UDP port after NAT.
DstIPAddr(1007)=202.38.1.2	Destination IP address before NAT.
DstPort(1008)=2048	Destination TCP or UDP port before NAT.
NatDstIPAddr(1009)=202.38.1.2	Destination IP address after NAT.
NatDstPort(1010)=259	Destination TCP or UDP port after NAT.
BeginTime_e(1013)=08102015200630	Start time of the flow, in the MMDDYYYYHHMMSS format.
EndTime_e(1014)=08102015200700	End time of the flow, in the MMDDYYYYHHMMSS format.

‌

Example: Configuring NAT log export to the log server

Network configuration

As shown in Figure 18, configure the device to export the NAT logs to the log server. The NAT logs in the log server are used for monitoring the internal user.

Figure 18 Network diagram

‌

Prerequisites

Assign IP addresses to interfaces on the device. Make sure the routes between the device and the user and between the device and the log server are reachable.

Procedure

# Enable NAT logging.

<Device> system-view

[Device] nat log enable

# Enable logging for NAT session establishment events.

[Device] nat log flow-begin

# Enable logging for NAT session removal events.

[Device] nat log flow-end

# Enable logging for active NAT flows and set the logging interval to 10 minutes.

[Device] nat log flow-active 10

# Set the flow log version to 3.0.

[Device] userlog flow export version 3

# Export flow log entries to port 2000 on the log host at 1.2.3.6.

[Device] userlog flow export host 1.2.3.6 port 2000

# Specify 2.2.2.2 as the source IP address for flow log packets.

[Device] userlog flow export source-ip 2.2.2.2

[Device] quit

Verifying the configuration

# Display the flow log configuration and statistics.

<Device> display userlog export

Flow:

Export flow log as UDP Packet.

Version: 3.0

Source ipv4 address: 2.2.2.2

Source ipv6 address:

Log load balance function: Disabled

Local time stamp: Disabled

Number of log hosts: 1

Log host 1:

Host/Port: 1.2.3.6/2000

Total logs/UDP packets exported: 112/87

06-Layer 3—IP Services Configuration Guide

NAT overview

NAT translation methods

NO-PAT

PAT

Interface-based NAT tasks at a glance

Configuring static NAT

About this task

Configuring outbound one-to-one static NAT on an interface

About this task

Configuring outbound net-to-net static NAT on an interface

Configuring dynamic NAT

About this task

Restrictions and guidelines

Configuring NAT server mappings

Configuring common NAT server mappings on an interface

Restrictions and guidelines

Procedure

Configuring load sharing NAT server mappings on an interface

Restrictions and guidelines

Procedure

Configuring port block-based NAT

Restrictions and guidelines

Procedure

Procedure

Enabling flow-triggered port block assignment

Restrictions and guidelines

Procedure

Configuring NAT DNS mapping

Restrictions and guidelines

Procedure

Configuring NAT logging

About this task

Procedure

Configuring NAT444 user logging

About this task

Prerequisites

Procedure

About this task

Procedure

About this task

Prerequisites

Procedure

Display and maintenance commands for NAT

Network configuration

Procedure

Verifying the configuration

Network configuration

Procedure

Verifying the configuration

Network configuration

Analysis

Procedure

Verifying the configuration

Example: Configuring NAT Server for external-to-internal access

Network configuration

Procedure

Verifying the configuration

Network configuration

Analysis

Procedure

Verifying the configuration

Network configuration

Requirements analysis

Procedure

Verifying the configuration

Network configuration

Requirements analysis

Procedure

Verifying the configuration

Network configuration

Requirements analysis

Procedure

Verifying the configuration

Network configuration

Procedure

Verifying the configuration

Network configuration

Requirements analysis

Procedure