WRED avoids global TCP synchronization by randomly dropping packets before a queue is full. WRED sets an upper threshold and lower threshold for each queue, and processes the packets in a queue as follows:

· When the queue size is shorter than the lower threshold, no packet is dropped.

· When the queue size reaches the upper threshold, all subsequent packets are dropped.

· When the queue size is between the lower threshold and the upper threshold, the received packets are dropped at random. The drop probability in a queue increases along with the queue size under the maximum drop probability.

WRED can discard packets based on the IP precedence, DSCP, or MPLS EXP value and selectively discard low-priority packets.

Through combining WRED with WFQ, the flow-based WRED can be realized.

WRED has the following types:

· Port-based WRED: Applies WRED to all packets on a port.

· Queue-based WRED: Applies WRED to only packets on WRED-enabled queues.

· Drop level-based WRED: Applies different WRED parameters to packets with different WRED parameters.

· ACL-based WRED: Applies different WRED parameters to packets matching different ACLs.

· 802.1p-based WRED: Applies different WRED parameters to packets with different 802.1p priorities.

· EXP-based WRED: Applies different WRED parameters to packets with different EXP priorities.

· ATM CLP-based WRED: Applies different WRED parameters to packets with different CLP priorities.

· DSCP-based WRED: Applies different WRED parameters to packets with different DSCP values.

· IP precedence-based WRED: Applies different WRED parameters to packets with different IP precedences.

· FR DE-based WRED: Applies different WRED parameters to packets with different DE bit settings.

ComwareV500R002 supports two WRED configuration approaches:

· Interface configuration—Configure WRED parameters on an interface or PVC and enable WRED.

· WRED table configuration—Configure a WRED table in system view and then apply the WRED table to an interface. A maximum number of 64 WRED tables is supported.

Aggregate CAR

Some switch models support aggregate CAR.

An aggregate CAR action is created globally. It can be directly applied to interfaces or used in the traffic behaviors associated with different traffic classes to police multiple traffic flows as a whole. The total rate of the traffic flows must conform to the traffic policing specifications set in the aggregate CAR action.

MIB file name

hh3c-ifqos2.mib

Root object

iso(1).org(3).dod(6).internet(1).private(4).huawei(2011).hh3c(10).hh3cCommon(2).hh3cQos2(65).hh3cIfQos2(1)

Scalar objects

hh3cIfQoSChassis

Object (OID)

Access

Syntax

Value range

Description

Implementation

hh3cIfQoSChassis

(1.3.6.1.4.1.25506.2.65.1.15.1)

accessible-for-notify

Integer32

0..65534

Chassis number.

hh3cIfQoSSlot

Object (OID)

Access

Syntax

Value range

Description

Implementation

hh3cIfQoSSlot

(1.3.6.1.4.1.25506.2.65.1.15.2)

accessible-for-notify

Integer32

0..65534

Slot number.

hh3cIfQoSCPU

Object (OID)

Access

Syntax

Value range

Description

Implementation

hh3cIfQoSCPU

(1.3.6.1.4.1.25506.2.65.1.15.3)

accessible-for-notify

Integer32

0..65534

CPU number.

hh3cIfQoSChip

Object (OID)

Access

Syntax

Value range

Description

Implementation

hh3cIfQoSChip

(1.3.6.1.4.1.25506.2.65.1.15.4)

accessible-for-notify

Integer32

0..65534

Chip number.

hh3cIfQoSIfName

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSIfName (1.3.6.1.4.1.25506.2.65.1.15.5)	accessible-for-notify	OCTET STRING	SIZE (1..47)	Interface name.

hh3cIfQoSDirection

Object (OID)

Access

Syntax

Value range

Description

Implementation

hh3cIfQoSDirection

(1.3.6.1.4.1.25506.2.65.1.15.6)

accessible-for-notify

Direction

Standard MIB values.

Direction.

hh3cIfQoSPassPacketRate

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSPassPacketRate (1.3.6.1.4.1.25506.2.65.1.15.7)	read-only	Unsigned32	Standard MIB values.	Traffic rate.

hh3cIfQoSCoppProtocol

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSCoppProtocol (1.3.6.1.4.1.25506.2.65.1.15.8)	read-only	OCTET STRING	SIZE (1..31)	Protocol type.

hh3cIfQoSBandwidth

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSBandwidth (1.3.6.1.4.1.25506.2.65.1.15.9)	read-only	Unsigned32	Standard MIB values.	Bandwidth.

hh3cIfQoSServiceName

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSServiceName (1.3.6.1.4.1.25506.2.65.1.15.10)	read-only	OCTET STRING	SIZE (1..63)	Service name.

hh3cIfQoSApplyObject

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSApplyObject (1.3.6.1.4.1.25506.2.65.1.15.11)	read-only	OCTET STRING	SIZE (1..127)	Application object.

hh3cIfQoSFailReason

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSFailReason (1.3.6.1.4.1.25506.2.65.1.15.12)	read-only	OCTET STRING	SIZE (1..127)	Failure causes.

hh3cIfQoSBandwidthUnit

Object (OID)

Access

Syntax

Value range

Description

Implementation

hh3cIfQoSBandwidthUnit (1.3.6.1.4.1.25506.2.65.1.15.13)

read-only

INTEGER

· unitUnavailable (0)

· unitAbsolute (1)

· unitAbsolutePPS (4)

Bandwidth unit.

hh3cIfQoSAggregativeCarNextIndex

Object (OID)	Access	Syntax	Value range	Description	Implementation
1.3.6.1.4.1.25506.2.65.1.4.1.1 (hh3cIfQoSAggregativeCarNextIndex)	read-only	Integer32	1..65534	Aggregate CAR index.	As per the MIB.

hh3cIfQoSWredGroupNextIndex

Object (OID)	Access	Syntax	Value range	Description	Implementation
1.3.6.1.4.1.25506.2.65.1.6.1.1 (hh3cIfQoSWredGroupNextIndex)	read-only	Integer32	0..256	WRED group index.	Implementation varies by product.

hh3cQoSTypeOfServiceMode

Object (OID)

Access

Syntax

Value range

Description

Implementation

1.3.6.1.4.1.25506.2.65.1.12.7.1 (hh3cQoSTypeOfServiceMode)

read-write

Integer32

· disabled (1)

· ipPrecedence (2)

· dscp (3)

· disabled (4)

Global service type.

hh3cQoSTypeOfServiceMode

Object (OID)

Access

Syntax

Value range

Description

Implementation

1.3.6.1.4.1.25506.2.65.1.13.1 (hh3cIfQoSProcessingStatus)

read-only

Integer32

· idle (1)

· busy (2)

QoS module processing status.

Tabular objects

hh3cIfQoSQSModeTable

About this table

This table specifies the queuing mode. This table and hh3cIfQoSQSWeightTable together configure the queuing settings.

Support for operations

Create	Edit/Modify	Delete	Read
Not supported	Supported	Not supported	Supported

Columns

The table index is ifIndex.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSQSMode (1.3.6.1.4.1.25506.2.65.1.1.1.1.1.1)	read-write	INTEGER	· sp(1) · sp0(2) · sp1(3) · sp2(4) · wrr(5) · hwfq(6) · wrr-sp(7) · byteCountWrr(8)byteCountWfq(9) · gmb(10)	Queuing mode.	Implementation varies by product.

Object (OID)

Access

Syntax

Value range

Description

Implementation

hh3cIfQoSQSMode (1.3.6.1.4.1.25506.2.65.1.1.1.1.1.1)

read-write

INTEGER

· sp(1)

· sp0(2)

· sp1(3)

· sp2(4)

· wrr(5)

· hwfq(6)

· wrr-sp(7)

· byteCountWrr(8)byteCountWfq(9)

· gmb(10)

Queuing mode.

Implementation varies by product.

hh3cIfQoSQSWeightTable

About this table

This table configures attributes for non-SP queues. This table and hh3cIfQoSQSModeTable together configure the queuing settings.

Support for operations

Create	Edit/Modify	Delete	Read
Not supported	Supported	Not supported	Supported

Columns

The table indexes are ifIndex and hh3cIfQoSQueueID.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSQueueID (1.3.6.1.4.1.25506.2.65.1.1.1.2.1.1)	not-accessible	Integer32	Standard MIB values.	Queue ID.	As per the MIB.
hh3cIfQoSQueueGroupType (1.3.6.1.4.1.25506.2.65.1.1.1.2.1.2)	read-write	INTEGER	· group0(1) · group1(2) · group2(3) · group3(4) · group4(5)	WRR group.	Implementation varies by product.
hh3cIfQoSQSType (1.3.6.1.4.1.25506.2.65.1.1.1.2.1.3)	read-write	INTEGER	· weight(1) · byte-count(2)	Queuing type.	As per the MIB.
hh3cIfQoSQSValue (1.3.6.1.4.1.25506.2.65.1.1.1.2.1.4)	read-write	Integer32	Standard MIB values.	Scheduling weight.	As per the MIB.
hh3cIfQoSQSMaxDelay (1.3.6.1.4.1.25506.2.65.1.1.1.2.1.5)	read-write	Integer32	Standard MIB values.	Maximum delay.	Not supported. The value is fixed at 9.
hh3cIfQoSQSMinBandwidth (1.3.6.1.4.1.25506.2.65.1.1.1.2.1.6)	read-write	Integer32	Standard MIB values.	Minimum guaranteed bandwidth.	Implementation varies by product.
hh3cIfQoSQSMinBandwidthPercent(1.3.6.1.4.1.25506.2.65.1.1.1.2.1.7)	read-write	Unsigned32	· 0..100 · 255	Percentage of the minimum guaranteed bandwidth to the available bandwidth.	Implementation varies by product.

hh3cIfQoSHardwareQueueRunInfoTable

About this table

This table contains queue-based traffic statistics.

Support for operations

Create	Edit/Modify	Delete	Read
Not supported	Not supported	Not supported	Supported

Columns

The table indexes are ifIndex and hh3cIfQoSQueueID.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSPassPackets (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.1)	read-only	Counter64	Standard MIB values.	Number of forwarded packets.	As per the MIB.
hh3cIfQoSDropPackets (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.2)	read-only	Counter64	Standard MIB values.	Number of dropped packets.	As per the MIB.
hh3cIfQoSPassBytes (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.3)	read-only	Counter64	Standard MIB values.	Number of forwarded bytes.	As per the MIB.
hh3cIfQoSPassPPS (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.4)	read-only	Unsigned32	Standard MIB values.	Packet forwarding rate in packets per second.	As per the MIB.
hh3cIfQoSPassBPS (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.5)	read-only	Unsigned32	Standard MIB values.	Packet forwarding rate in bytes per second.	As per the MIB.
hh3cIfQoSDropBytes (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.6)	read-only	Counter64	Standard MIB values.	Number of dropped bytes.	As per the MIB.
hh3cIfQoSQueueLengthInPkts (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.7)	read-only	Unsigned32	Standard MIB values.	Maximum queue length in packets.	As per the MIB.
hh3cIfQoSQueueLengthInBytes (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.8)	read-only	Unsigned32	Standard MIB values.	Maximum queue length in bytes.	Not supported
hh3cIfQoSCurQueuePkts (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.9)	read-only	Unsigned32	Standard MIB values.	Current queue length in packets.	Not supported
hh3cIfQoSCurQueueBytes (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.10)	read-only	Unsigned32	Standard MIB values.	Current queue length in bytes.	Not supported
hh3cIfQoSCurQueuePPS (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.11)	read-only	Unsigned32	Standard MIB values.	Number of packets enqueued per second.	Not supported
hh3cIfQoSCurQueueBPS (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.12)	read-only	Unsigned32	Standard MIB values.	Number of bytes enqueued per second.	Not supported
hh3cIfQoSTailDropPkts (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.13)	read-only	Counter64	Standard MIB values.	Number of packets dropped by tail drop.	Not supported
hh3cIfQoSTailDropBytes (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.14)	read-only	Counter64	Standard MIB values.	Number of bytes dropped by tail drop.	Not supported
hh3cIfQoSTailDropPPS (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.15)	read-only	Unsigned32	Standard MIB values.	Number of packets dropped per second by tail drop.	Not supported
hh3cIfQoSTailDropBPS (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.16)	read-only	Unsigned32	Standard MIB values.	Number of bytes dropped per second by tail drop.	Not supported
hh3cIfQoSWredDropPkts (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.17)	read-only	Counter64	Standard MIB values.	Number of packets dropped by WRED.	Not supported
hh3cIfQoSWredDropBytes (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.18)	read-only	Counter64	Standard MIB values.	Number of bytes dropped by WRED.	Not supported
hh3cIfQoSWredDropPPS (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.19)	read-only	Unsigned32	Standard MIB values.	Number of packets dropped per second by WRED.	Not supported
hh3cIfQoSWredDropBPS (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.20)	read-only	Unsigned32	Standard MIB values.	Number of bytes dropped per second by WRED.	Not supported
hh3cIfQoSPeakPassPPS (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.24)	read-only	Unsigned32	Standard MIB values.	Peak number of packets forwarded.	As per the MIB.
hh3cIfQoSPeakPassBPS (1.3.6.1.4.1.25506.2.65.1.1.2.1.1.25)	read-only	Unsigned32	Standard MIB values.	Peak number of bytes forwarded.	As per the MIB.

hh3cIfQoSHQueueTcpRunInfoTable

About this table

This table contains queue-based traffic statistics on TCP packets and non-TCP packets.

Support for operations

Create	Edit/Modify	Delete	Read
Not supported	Not supported	Not supported	Supported

Columns

The table indexes are ifIndex and hh3cIfQoSQueueID.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSWredDropLPreNTcpPkts (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.1)	read-only	Counter64	Standard MIB values.	Number of low-priority non-TCP packets dropped by WRED.	As per the MIB.
hh3cIfQoSWredDropLPreNTcpBytes (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.2)	read-only	Counter64	Standard MIB values.	Number of low-priority non-TCP bytes dropped by WRED.	As per the MIB.
hh3cIfQoSWredDropLPreNTcpPPS (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.3)	read-only	Unsigned32	Standard MIB values.	Number of low-priority non-TCP packets dropped by WRED per second.	As per the MIB.
hh3cIfQoSWredDropLPreNTcpBPS (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.4)	read-only	Unsigned32	Standard MIB values.	Number of low-priority non-TCP bytes dropped by WRED per second.	As per the MIB.
hh3cIfQoSWredDropLPreTcpPkts (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.5)	read-only	Counter64	Standard MIB values.	Number of low-priority TCP packets dropped by WRED.	As per the MIB.
hh3cIfQoSWredDropLPreTcpBytes (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.6)	read-only	Counter64	Standard MIB values.	Number of low-priority TCP bytes dropped by WRED.	As per the MIB.
hh3cIfQoSWredDropLPreTcpPPS (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.7)	read-only	Unsigned32	Standard MIB values.	Number of low-priority TCP packets dropped by WRED per second.	As per the MIB.
hh3cIfQoSWredDropLPreTcpBPS (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.8)	read-only	Unsigned32	Standard MIB values.	Number of low-priority TCP bytes dropped by WRED per second.	As per the MIB.
hh3cIfQoSWredDropHPreNTcpPkts (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.9)	read-only	Counter64	Standard MIB values.	Number of high-priority non-TCP packets dropped by WRED.	As per the MIB.
hh3cIfQoSWredDropHPreNTcpBytes (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.10)	read-only	Counter64	Standard MIB values.	Number of high-priority non-TCP bytes dropped by WRED.	As per the MIB.
hh3cIfQoSWredDropHPreNTcpPPS (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.11)	read-only	Unsigned32	Standard MIB values.	Number of high-priority non-TCP packets dropped by WRED per second.	As per the MIB.
hh3cIfQoSWredDropHPreNTcpBPS (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.12)	read-only	Unsigned32	Standard MIB values.	Number of high-priority non-TCP bytes dropped by WRED per second.	As per the MIB.
hh3cIfQoSWredDropHPreTcpPkts (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.13)	read-only	Counter64	Standard MIB values.	Number of high-priority TCP packets dropped by WRED.	As per the MIB.
hh3cIfQoSWredDropHPreTcpBytes (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.14)	read-only	Counter64	Standard MIB values.	Number of high-priority TCP bytes dropped by WRED.	As per the MIB.
hh3cIfQoSWredDropHPreTcpPPS (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.15)	read-only	Unsigned32	Standard MIB values.	Number of high-priority TCP packets dropped by WRED per second.	As per the MIB.
hh3cIfQoSWredDropHPreTcpBPS (1.3.6.1.4.1.25506.2.65.1.1.2.2.1.16)	read-only	Unsigned32	Standard MIB values.	Number of high-priority TCP bytes dropped by WRED per second.	As per the MIB.

hh3cIfQoSLRConfigTable

About this table

This table configures the inbound or outbound rate limit on an interface.

Support for operations

Create	Edit/Modify	Delete	Read
Supported	Supported	Supported	Supported

Columns

The table indexes are ifIndex and hh3cIfQoSLRDirection.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSLRDirection (1.3.6.1.4.1.25506.2.65.1.3.1.1.1)	not-accessible	Direction	Standard MIB values.	Rate limit direction.	Implementation varies by product.
hh3cIfQoSLRCir (1.3.6.1.4.1.25506.2.65.1.3.1.1.2)	read-create	Unsigned32	Standard MIB values.	CIR.	Implementation varies by product.
hh3cIfQoSLRCbs (1.3.6.1.4.1.25506.2.65.1.3.1.1.3)	read-create	Unsigned32	Standard MIB values.	CBS.	Implementation varies by product.
hh3cIfQoSLREbs (1.3.6.1.4.1.25506.2.65.1.3.1.1.4)	read-create	Unsigned32	Standard MIB values.	EBS.	Implementation varies by product.
hh3cIfQoSRowStatus (1.3.6.1.4.1.25506.2.65.1.3.1.1.5)	read-create	RowStatus	Standard MIB values.	Row status.	· active(1) · createAndGo(4) · destroy(6)
hh3cIfQoSLRPir (1.3.6.1.4.1.25506.2.65.1.3.1.1.6)	read-create	Unsigned32	Standard MIB values.	PIR.	Implementation varies by product.
hh3cIfQoSLRUnit (1.3.6.1.4.1.25506.2.65.1.3.1.1.7)	read-create	INTEGER	· unitAbsolute(1) · unitPercent(2)	Rate limit unit.	Implementation varies by product.

hh3cIfQoSLRRunInfoTable

About this table

This table contains rate limit statistics on an interface.

Support for operations

Create	Edit/Modify	Delete	Read
Not supported	Not supported	Not supported	Supported

Columns

The table indexes are ifIndex and hh3cIfQoSLRDirection.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSLRRunInfoPassedPackets (1.3.6.1.4.1.25506.2.65.1.3.2.1.1)	read-only	Counter64	Standard MIB values.	Number of forwarded packets.	As per the MIB.
hh3cIfQoSLRRunInfoPassedBytes (1.3.6.1.4.1.25506.2.65.1.3.2.1.2)	read-only	Counter64	Standard MIB values.	Number of forwarded bytes.	As per the MIB.
hh3cIfQoSLRRunInfoDelayedPackets (1.3.6.1.4.1.25506.2.65.1.3.2.1.3)	read-only	Counter64	Standard MIB values.	Number of delayed packets.	As per the MIB.
hh3cIfQoSLRRunInfoDelayedBytes (1.3.6.1.4.1.25506.2.65.1.3.2.1.4)	read-only	Counter64	Standard MIB values.	Number of delayed bytes.	As per the MIB.
hh3cIfQoSLRRunInfoActiveShaping (1.3.6.1.4.1.25506.2.65.1.3.2.1.5)	read-only	INTEGER	· active(1) · inactive(2)	Rate limit configuration status.	As per the MIB.

hh3cIfQoSAggregativeCarConfigTable

About this table

This table contains aggregate CAR configuration, which can police the traffic on multiple ports. Routers do not support aggregate CAR. Some switch models support aggregate CAR.

Support for operations

Create	Edit/Modify	Delete	Read
Supported	Supported	Supported	Supported

Columns

The table index is hh3cIfQoSAggregativeCarIndex.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSAggregativeCarIndex (1.3.6.1.4.1.25506.2.65.1.4.1.2.1.1)	not-accessible	Integer32	1..65534	Aggregate CAR index.	As per the MIB.
hh3cIfQoSAggregativeCarName (1.3.6.1.4.1.25506.2.65.1.4.1.2.1.2)	read-create	OCTET STRING	SIZE (1..31)	Aggregate CAR name.	As per the MIB.
hh3cIfQoSAggregativeCarCir (1.3.6.1.4.1.25506.2.65.1.4.1.2.1.3)	read-create	Unsigned32	Standard MIB values.	CIR.	As per the MIB.
hh3cIfQoSAggregativeCarCbs (1.3.6.1.4.1.25506.2.65.1.4.1.2.1.4)	read-create	Unsigned32	Standard MIB values.	CBS.	Implementation varies by product.
hh3cIfQoSAggregativeCarEbs (1.3.6.1.4.1.25506.2.65.1.4.1.2.1.5)	read-create	Unsigned32	Standard MIB values.	EBS.	Implementation varies by product.
hh3cIfQoSAggregativeCarPir (1.3.6.1.4.1.25506.2.65.1.4.1.2.1.6)	read-create	Unsigned32	Standard MIB values.	PIR.	Implementation varies by product.
hh3cIfQoSAggregativeCarGreenActionType (1.3.6.1.4.1.25506.2.65.1.4.1.2.1.7)	read-create	Hh3cIfCarAction	Standard MIB values.	Action to take on green packets.	Implementation varies by product.
hh3cIfQoSAggregativeCarGreenActionValue (1.3.6.1.4.1.25506.2.65.1.4.1.2.1.8)	read-create	Integer32	· 0..63 · 255	Value to mark for green packets.	Implementation varies by product.
hh3cIfQoSAggregativeCarYellowActionType (1.3.6.1.4.1.25506.2.65.1.4.1.2.1.9)	read-create	Hh3cIfCarAction	Standard MIB values.	Action to take on yellow packets.	Implementation varies by product.
hh3cIfQoSAggregativeCarYellowActionValue (1.3.6.1.4.1.25506.2.65.1.4.1.2.1.10)	read-create	Integer32	· 0..63 · 255	Value to mark for yellow packets.	Implementation varies by product.
hh3cIfQoSAggregativeCarRedActionType (1.3.6.1.4.1.25506.2.65.1.4.1.2.1.11)	read-create	Hh3cIfCarAction	Standard MIB values.	Action to take on red packets.	Implementation varies by product.
hh3cIfQoSAggregativeCarRedActionValue (1.3.6.1.4.1.25506.2.65.1.4.1.2.1.12)	read-create	Integer	· 0..63 · 255	Value to mark for red packets.	Implementation varies by product.
hh3cIfQoSAggregativeCarType (1.3.6.1.4.1.25506.2.65.1.4.1.2.1.13)	read-create	INTEGER	· aggregative(1) · NotAggregative(2) · hierarchy(3)	Aggregate CAR type.	Implementation varies by product.
hh3cIfQoSAggregativeCarRowStatus (1.3.6.1.4.1.25506.2.65.1.4.1.2.1.14)	read-create	RowStatus	Standard MIB values.	Row status.	As per the MIB.

hh3cIfQoSAggregativeCarApplyTable

About this table

This table contains aggregate CAR application information for an interface.

Support for operations

Create	Edit/Modify	Delete	Read
Supported	Supported	Supported	Supported

Columns

The table indexes are ifIndex, hh3cIfQoSAggregativeCarApplyDirection, hh3cIfQoSAggregativeCarApplyRuleType, and hh3cIfQoSAggregativeCarApplyRuleValue.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSAggregativeCarApplyDirection (1.3.6.1.4.1.25506.2.65.1.4.1.3.1.1)	not-accessible	Direction	Standard MIB values.	CAR direction.	Implementation varies by product.
hh3cIfQoSAggregativeCarApplyRuleType (1.3.6.1.4.1.25506.2.65.1.4.1.3.1.2)	not-accessible	INTEGER	· ipv4acl(1) · ipv6acl(2) · carl(3) · any(4)	CAR type.	Implementation varies by product.
hh3cIfQoSAggregativeCarApplyRuleValue (1.3.6.1.4.1.25506.2.65.1.4.1.3.1.3)	not-accessible	Integer32	0..2147483647	CAR type value.	.Implementation varies by product.
hh3cIfQoSAggregativeCarApplyCarIndex (1.3.6.1.4.1.25506.2.65.1.4.1.3.1.4)	read-create	Integer32	1..65534	Aggregate CAR index.	As per the MIB.
hh3cIfQoSAggregativeCarApplyRowStatus (1.3.6.1.4.1.25506.2.65.1.4.1.3.1.5)	read-create	RowStatus	Standard MIB values.	Row status.	As per the MIB.

hh3cIfQoSAggregativeCarRunInfoTable

About this table

This table contains aggregate CAR statistics.

Support for operations

Create	Edit/Modify	Delete	Read
Not supported	Not supported	Not supported	Not supported

Columns

The table index is hh3cIfQoSAggregativeCarIndex.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSAggregativeCarGreenPackets (1.3.6.1.4.1.25506.2.65.1.4.1.4.1.1)	read-only	Counter64	Standard MIB values.	Number of green packets.	Implementation varies by product.
hh3cIfQoSAggregativeCarGreenBytes (1.3.6.1.4.1.25506.2.65.1.4.1.4.1.2)	read-only	Counter64	Standard MIB values.	Number of green bytes.	Implementation varies by product.
hh3cIfQoSAggregativeCarYellowPackets (1.3.6.1.4.1.25506.2.65.1.4.1.4.1.3)	read-only	Counter64	Standard MIB values.	Number of yellow packets.	Implementation varies by product.
hh3cIfQoSAggregativeCarYellowBytes (1.3.6.1.4.1.25506.2.65.1.4.1.4.1.4)	read-only	Counter64	Standard MIB values.	Number of yellow bytes.	Implementation varies by product.
hh3cIfQoSAggregativeCarRedPackets (1.3.6.1.4.1.25506.2.65.1.4.1.4.1.5)	read-only	Counter64	Standard MIB values.	Number of red packets.	Implementation varies by product.
hh3cIfQoSAggregativeCarRedBytes (1.3.6.1.4.1.25506.2.65.1.4.1.4.1.6)	read-only	Counter64	Standard MIB values.	Number of red bytes.	Implementation varies by product.

hh3cIfQoSTricolorCarConfigTable

About this table

This table contains three-color CAR configuration.

Support for operations

Create	Edit/Modify	Delete	Read
Supported	Supported	Supported	Supported

Columns

The table index is hh3cIfQoSAggregativeCarIndex.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSTricolorCarDirection (1.3.6.1.4.1.25506.2.65.1.4.2.1.1.1)	not-accessible	Direction	Standard MIB values.	Aggregate CAR index.	Implementation varies by product.
hh3cIfQoSTricolorCarType (1.3.6.1.4.1.25506.2.65.1.4.2.1.1.2)	not-accessible	INTEGER	· ipv4acl(1) · ipv6acl(2) · carl(3) · any(4)	Aggregate CAR name.	Implementation varies by product.
hh3cIfQoSTricolorCarValue (1.3.6.1.4.1.25506.2.65.1.4.2.1.1.3)	not-accessible	Integer32	0..2147483647	CAR.	Implementation varies by product.
hh3cIfQoSTricolorCarCir (1.3.6.1.4.1.25506.2.65.1.4.2.1.1.4)	read-create	Unsigned32	Standard MIB values.	CIR.	Implementation varies by product.
hh3cIfQoSTricolorCarCbs (1.3.6.1.4.1.25506.2.65.1.4.2.1.1.5)	read-create	Unsigned32	Standard MIB values.	CBS.	Implementation varies by product.
hh3cIfQoSTricolorCarEbs (1.3.6.1.4.1.25506.2.65.1.4.2.1.1.6)	read-create	Unsigned32	Standard MIB values.	EBS.	Implementation varies by product.
hh3cIfQoSTricolorCarPir (1.3.6.1.4.1.25506.2.65.1.4.2.1.1.7)	read-create	Unsigned32	Standard MIB values.	PIR.	Implementation varies by product.
hh3cIfQoSTricolorCarGreenActionType (1.3.6.1.4.1.25506.2.65.1.4.2.1.1.8)	read-create	Hh3cIfCarAction	Standard MIB values.	Action to take on green packets.	Implementation varies by product.
hh3cIfQoSTricolorCarGreenActionValue (1.3.6.1.4.1.25506.2.65.1.4.2.1.1.9)	read-create	Integer32	· 0..63 · 255	Value to mark for green packets.	Implementation varies by product.
hh3cIfQoSTricolorCarYellowActionType (1.3.6.1.4.1.25506.2.65.1.4.2.1.1.10)	read-create	Hh3cIfCarAction	Standard MIB values.	Action to take on yellow packets.	Implementation varies by product.
hh3cIfQoSTricolorCarYellowActionValue (1.3.6.1.4.1.25506.2.65.1.4.2.1.1.11)	read-create	Integer32	· 0..63 · 255	Value to mark for yellow packets.	Implementation varies by product.
hh3cIfQoSTricolorCarRedActionType (1.3.6.1.4.1.25506.2.65.1.4.2.1.1.12)	read-create	Hh3cIfCarAction	Standard MIB values.	Action to take on red packets.	Implementation varies by product.
hh3cIfQoSTricolorCarRedActionValue (1.3.6.1.4.1.25506.2.65.1.4.2.1.1.13)	read-create	Integer32	· 0..63 · 255	Value to mark for red packets.	Implementation varies by product.
hh3cIfQoSTricolorCarRowStatus (1.3.6.1.4.1.25506.2.65.1.4.2.1.1.14)	read-create	RowStatus	Standard MIB values.	Row status.	As per the MIB.
hh3cIfQoSTricolorCarUnitType (1.3.6.1.4.1.25506.2.65.1.4.2.1.1.15)	read-create	INTEGER	· unitAbsolute(1) · unitPercent(2)	Rate limit unit.	.Implementation varies by product.

hh3cIfQoSTricolorCarRunInfoTable

About this table

This table contains three-color CAR statistics.

Support for operations

Create	Edit/Modify	Delete	Read
Not supported	Not supported	Not supported	Supported

Columns

The table indexes are ifIndex, hh3cIfQoSTricolorCarDirection, hh3cIfQoSTricolorCarType, and hh3cIfQoSTricolorCarValue.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSTricolorCarGreenPackets (1.3.6.1.4.1.25506.2.65.1.4.2.2.1.1)	read-only	Counter64	Standard MIB values.	Number of green packets.	Implementation varies by product.
hh3cIfQoSTricolorCarGreenBytes (1.3.6.1.4.1.25506.2.65.1.4.2.2.1.2)	read-only	Counter64	Standard MIB values.	Number of green bytes.	Implementation varies by product.
hh3cIfQoSTricolorCarYellowPackets (1.3.6.1.4.1.25506.2.65.1.4.2.2.1.3)	read-only	Counter64	Standard MIB values.	Number of yellow packets.	Implementation varies by product.
hh3cIfQoSTricolorCarYellowBytes (1.3.6.1.4.1.25506.2.65.1.4.2.2.1.4)	read-only	Counter64	Standard MIB values.	Number of yellow bytes.	Implementation varies by product.
hh3cIfQoSTricolorCarRedPackets (1.3.6.1.4.1.25506.2.65.1.4.2.2.1.5)	read-only	Counter64	Standard MIB values.	Number of red packets.	Implementation varies by product.
hh3cIfQoSTricolorCarRedBytes (1.3.6.1.4.1.25506.2.65.1.4.2.2.1.6)	read-only	Counter64	Standard MIB values.	Number of red bytes.	Implementation varies by product.

hh3cIfQoSGTSConfigTable

About this table

This table contains GTS configuration information.

Support for operations

Create	Edit/Modify	Delete	Read
Supported	Supported	Supported	Supported

Columns

The table indexes are ifIndex, hh3cIfQoSGTSClassRuleType, and hh3cIfQoSGTSClassRuleValue.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSGTSClassRuleType (1.3.6.1.4.1.25506.2.65.1.5.1.1.1)	not-accessible	INTEGER	· any(1) · ipv4acl(2) · ipv6acl(3) · queue(4)	GTS type.	Supports only queue(4).
hh3cIfQoSGTSClassRuleValue (1.3.6.1.4.1.25506.2.65.1.5.1.1.2)	not-accessible	Integer32	0..2147483647	GTS type value.	The value range is 0 to 7.
hh3cIfQoSGTSCir (1.3.6.1.4.1.25506.2.65.1.5.1.1.3)	read-create	Unsigned32	Standard MIB values.	CIR.	· The value range is 300 to 1000000 for GE interfaces. · The value range is 300 to 10000000 for 10-GE interfaces. · The value range is 300 to 40000000 for 40-GE interfaces. · The value range is 300 to 100000000 for 100-GE interfaces.
hh3cIfQoSGTSCbs (1.3.6.1.4.1.25506.2.65.1.5.1.1.4)	read-create	Unsigned32	Standard MIB values.	CBS.	· The value range is 4096 to 133169152 for GE interfaces. · The value range is 4096 to 133169152 for 10-GE interfaces. · The value range is 4096 to 535822336 for 40-GE interfaces. · The value range is 4096 to 1341128704 for 100-GE interfaces.
hh3cIfQoSGTSEbs (1.3.6.1.4.1.25506.2.65.1.5.1.1.5)	read-create	Unsigned32	Standard MIB values.	EBS in bytes.	Not supported.
hh3cIfQoSGTSQueueLength (1.3.6.1.4.1.25506.2.65.1.5.1.1.6)	read-create	Integer32	Standard MIB values.	Queue length.	Not supported.
hh3cIfQoSGTSConfigRowStatus (1.3.6.1.4.1.25506.2.65.1.5.1.1.7)	read-create	RowStatus	Standard MIB values.	Row status.	· active(1) · createAndGo(4) · destroy(6)
hh3cIfQoSGTSPir (1.3.6.1.4.1.25506.2.65.1.5.1.1.8)	read-create	Unsigned32	Standard MIB values.	PIR.	Not supported.
hh3cIfQoSGTSUnitType (1.3.6.1.4.1.25506.2.65.1.5.1.1.9)	read-create	INTEGER	· unitAbsolute (1) · unitPercent(2)	GTS unit.	Supports only unitAbsolute(1).

hh3cIfQoSGTSRunInfoTable

About this table

This table contains GTS statistics.

Support for operations

Create	Edit/Modify	Delete	Read
Not supported	Not supported	Not supported	Supported

Columns

The table indexes are ifIndex, hh3cIfQoSGTSClassRuleType, and hh3cIfQoSGTSClassRuleValue.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSGTSQueueSize (1.3.6.1.4.1.25506.2.65.1.5.2.1.1)	read-only	Integer32	Standard MIB values.	Current number of packets in the queue.	As per the MIB.
hh3cIfQoSGTSPassedPackets (1.3.6.1.4.1.25506.2.65.1.5.2.1.2)	read-only	Counter64	Standard MIB values.	Number of forwarded packets.	As per the MIB.
hh3cIfQoSGTSPassedBytes (1.3.6.1.4.1.25506.2.65.1.5.2.1.3)	read-only	Counter64	Standard MIB values.	Number of forwarded bytes.	As per the MIB.
hh3cIfQoSGTSDiscardPackets (1.3.6.1.4.1.25506.2.65.1.5.2.1.4)	read-only	Counter64	Standard MIB values.	Number of dropped packets.	As per the MIB.
hh3cIfQoSGTSDiscardBytes (1.3.6.1.4.1.25506.2.65.1.5.2.1.5)	read-only	Counter64	Standard MIB values.	Number of dropped bytes.	As per the MIB.
hh3cIfQoSGTSDelayedPackets (1.3.6.1.4.1.25506.2.65.1.5.2.1.6)	read-only	Counter64	Standard MIB values.	Number of delayed packets.	As per the MIB.
hh3cIfQoSGTSDelayedBytes (1.3.6.1.4.1.25506.2.65.1.5.2.1.7)	read-only	Counter64	Standard MIB values.	Number of delayed bytes.	As per the MIB.

hh3cIfQoSWredGroupTable

About this table

This table creates a WRED table.

Support for operations

Create	Edit/Modify	Delete	Read
Supported	Supported	Supported	Supported

Columns

The table index is hh3cIfQoSWredGroupIndex.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSWredGroupIndex (1.3.6.1.4.1.25506.2.65.1.6.1.2.1.1)	not-accessible	Integer32	0..256	WRED table index.	Implementation varies by product.
hh3cIfQoSWredGroupName (1.3.6.1.4.1.25506.2.65.1.6.1.2.1.2)	read-create	OCTET STRING	SIZE (1..32)	WRED table name.	As per the MIB.
hh3cIfQoSWredGroupType (1.3.6.1.4.1.25506.2.65.1.6.1.2.1.3)	read-create	INTEGER	· userdefined(0) · dot1p(1) · ippre(2) · dscp(3) · localpre(4) · atmclp(5) · frde(6) · exp(7) · queue(8) · dropLevel(9)	WRED table type.	.Implementation varies by product.
hh3cIfQoSWredGroupWeightingConstant (1.3.6.1.4.1.25506.2.65.1.6.1.2.1.4)	read-create	Integer32	1..15	WRED exponent for average queue size calculation.	The default value is 9.
hh3cIfQoSWredGroupRowStatus (1.3.6.1.4.1.25506.2.65.1.6.1.2.1.6)	read-create	RowStatus	Standard MIB values.	Row status.	As per the MIB.

hh3cIfQoSWredGroupContentTable

About this table

This table configures a WRED table.

Support for operations

Create	Edit/Modify	Delete	Read
Not supported	Supported	Not supported	Supported

Columns

The table indexes are hh3cIfQoSWredGroupIndex, hh3cIfQoSWredGroupContentIndex, and hh3cIfQoSWredGroupContentSubIndex.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSWredGroupContentIndex (1.3.6.1.4.1.25506.2.65.1.6.1.3.1.1)	not-accessible	Integer32	0..63	Second index.	Implementation varies by product.
hh3cIfQoSWredGroupContentSubIndex (1.3.6.1.4.1.25506.2.65.1.6.1.3.1.2)	not-accessible	Integer32	0..63	Third index.	Implementation varies by product.
hh3cIfQoSWredLowLimit (1.3.6.1.4.1.25506.2.65.1.6.1.3.1.3)	read-create	Integer32	Standard MIB values.	Lower limit.	Implementation varies by product.
hh3cIfQoSWredHighLimit (1.3.6.1.4.1.25506.2.65.1.6.1.3.1.4)	read-create	Integer32	Standard MIB values.	Higher limit.	Implementation varies by product.
hh3cIfQoSWredDiscardProb (1.3.6.1.4.1.25506.2.65.1.6.1.3.1.5)	read-create	Integer32	Standard MIB values.	Drop probability.	Implementation varies by product.
hh3cIfQoSWredGroupExponent (1.3.6.1.4.1.25506.2.65.1.6.1.3.1.6)	read-create	Integer32	0..15	WRED exponent for average queue size calculation.	The default value is 9.
hh3cIfQoSWredRowStatus (1.3.6.1.4.1.25506.2.65.1.6.1.3.1.7)	read-create	RowStatus	Standard MIB values.	Row status.	As per the MIB.

hh3cIfQoSWredGroupApplyIfTable

About this table

This table contains WRED table application information for an interface.

Support for operations

Create	Edit/Modify	Delete	Read
Supported	Supported	Supported	Supported

Columns

The table index is ifIndex.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSWredGroupApplyIndex (1.3.6.1.4.1.25506.2.65.1.6.1.4.1.1)	read-create	Integer32	0..256	WRED table index.	As per the MIB.
hh3cIfQoSWredGroupApplyName (1.3.6.1.4.1.25506.2.65.1.6.1.4.1.2)	read-only	OCTET STRING	SIZE (1..32)	WRED table name.	As per the MIB.
hh3cIfQoSWredGroupIfRowStatus (1.3.6.1.4.1.25506.2.65.1.6.1.4.1.3)	read-create	RowStatus	Standard MIB values.	Row status.	As per the MIB.

hh3cIfQoSPortPriorityTable

About this table

This table contains the port priority. After the switch receives a packet, it performs priority mapping according to the configured priority trust mode. If no local precedence is successfully assigned or no packet priority is trusted, the switch uses the priority of the input interface as the local precedence or 802.1p priority for priority mapping. Routers do not support this table.

Support for operations

Create	Edit/Modify	Delete	Read
Not supported	Supported	Not supported	Supported

Columns

The table index is ifIndex.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSPortPriorityValue (1.3.6.1.4.1.25506.2.65.1.7.1.1.1.1)	read-write	Integer32	0..7	Port priority.	Implementation varies by product.

hh3cIfQoSPortPirorityTrustTable

About this table

This table contains the priority trust mode.

Support for operations

Create	Edit/Modify	Delete	Read
Not supported	Supported	Not supported	Supported

Columns

The table index is ifIndex.

Object (OID)

Access

Syntax

Value range

Description

Implementation

hh3cIfQoSPortPriorityTrustTrustType (1.3.6.1.4.1.25506.2.65.1.7.1.2.1.1)

read-write

INTEGER

· untrust(1)

· dot1p(2)

· dscp(3)

· exp(4)

· ipPrecedence (5)

· dot11e(6)

· auto(7)

Priority trust mode.

Implementation varies by product.

hh3cIfQoSPortPriorityTrustOvercastType (1.3.6.1.4.1.25506.2.65.1.7.1.2.1.2)

read-write

INTEGER

· noOvercast(1)

· overcastDSCP(2)

· overcastCOS(3)

· overcast(4)

Overwrite mode.

Implementation varies by product.

hh3cIfQoSPrePriMapTable

About this table

This table configures a priority map.

Support for operations

Create	Edit/Modify	Delete	Read
Not supported	Supported	Not supported	Supported

Columns

The table indexes are hh3cIfQoSPrePriMapTableType, hh3cIfQoSPrePriMapTableColor, hh3cIfQoSPrePriMapTableDirection, and hh3cIfQoSPrePriMapTableImportValue.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSPrePriMapTableType (1.3.6.1.4.1.25506.2.65.1.9.1.4.1.1)	not-accessible	INTEGER	· dot1pToLp(1) · dot1pToDp(2) · expToLp(3) · dscpToLp(4) · expToDp(5) · dscpToDp(6) · dscpToDot1p(7) · dot1pToDscp(8) · dscpToDscp(9) · dscpToExp(10) · expToDscp(11) · expToDot1p(12) · expToExp(13) · lpToDot1p(14) · dot1pToRpr(15) · dscpToRpr(16) · expToRpr(17) · ippreToRpr(18) · upToDot1p(19) · upToDscp(20) · upToExp(21) · upToDp(22) · upToLp(23) · upToRpr(24) · upToFc(25) · lpTodscp(26) · dot11eToLp(27) · lpToDot11e(28) · lpToLp(29) · dot1pToExp(30) · lpToExp(31) · lpToDp(32) · upToUp(33) · dot1pToDot1p(34)	Priority map type.	Implementation varies by product.
hh3cIfQoSPrePriMapTableColor (1.3.6.1.4.1.25506.2.65.1.9.1.4.1.2)	not-accessible	INTEGER	· nocolor(1) · green(2) · yellow(3) · red(4)	Priority map color.	Implementation varies by product.
hh3cIfQoSPrePriMapTableDirection (1.3.6.1.4.1.25506.2.65.1.9.1.4.1.3)	not-accessible	INTEGER	· nodirection(1) · inbound(2) · outbound(3)	Priority map direction.	Implementation varies by product.
hh3cIfQoSPrePriMapTableImportValue (1.3.6.1.4.1.25506.2.65.1.9.1.4.1.4)	not-accessible	Integer32	0..63	Input values of the priority map.	As per the MIB.
hh3cIfQoSPrePriMapTableExportValue (1.3.6.1.4.1.25506.2.65.1.9.1.4.1.5)	read-write	Integer32	0..63	Output values of the priority map.	As per the MIB.

hh3cQoSRemarkTcpPortPriTable

About this table

This table contains TCP port-based priority information.

Support for operations

Create	Edit/Modify	Delete	Read
Supported	Supported	Supported	Supported

Columns

The table index is hh3cQoSRemarkTcpPortStart.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cQoSRemarkTcpPortStart(1.3.6.1.4.1.25506.2.65.1.12.1.1.1)	not-accessible	Integer32	0..65535	Start port number of a TCP port range.	As per the MIB.
hh3cQoSRemarkTcpPortEnd (1.3.6.1.4.1.25506.2.65.1.12.1.1.2)	read-create	Integer32	0..65535	End port number of a TCP port range.	As per the MIB.
hh3cQoSRemarkTcpPortType (1.3.6.1.4.1.25506.2.65.1.12.1.1.3)	read-create	INTEGER	· ipAll(1) · ipv4(2) · ipv6(3)	IP type of matching packets.	As per the MIB.
hh3cQoSRemarkTcpPortDot1p (1.3.6.1.4.1.25506.2.65.1.12.1.1.4)	read-create	Unsigned32	· 0..7 · 255	802.1p priority value of matching packets.	As per the MIB.
hh3cQoSRemarkTcpPortDscp (1.3.6.1.4.1.25506.2.65.1.12.1.1.5)	read-create	Unsigned32	· 0..63 · 255	DSCP value of matching packets.	As per the MIB.
hh3cQoSRemarkTcpPortRowStatus (1.3.6.1.4.1.25506.2.65.1.12.1.1.6)	read-create	RowStatus	Standard MIB values.	Row status.	· active(1) · createAndGo(4) · destroy(6)

hh3cQoSRemarkUdpPortPriTable

About this table

This table contains UDP port-based priority information.

Support for operations

Create	Edit/Modify	Delete	Read
Supported	Supported	Supported

Columns

The table index is hh3cQoSRemarkUdpPortStart.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cQoSRemarkUdpPortStart (1.3.6.1.4.1.25506.2.65.1.12.2.1.1)	not-accessible	Integer32	0..65535	Start port number of a UDP port range.	As per the MIB.
hh3cQoSRemarkUdpPortEnd (1.3.6.1.4.1.25506.2.65.1.12.2.1.2)	read-create	Integer32	0..65535	End port number of the UDP port range.	As per the MIB.
hh3cQoSRemarkUdpPortType (1.3.6.1.4.1.25506.2.65.1.12.2.1.3)	read-create	INTEGER	· ipAll(1) · ipv4(2) · ipv6(3)	IP type of matching packets.	As per the MIB.
hh3cQoSRemarkUdpPortDot1p (1.3.6.1.4.1.25506.2.65.1.12.2.1.4)	read-create	Unsigned32	· 0..7 · 255	802.1p priority value of matching packets.	As per the MIB.
hh3cQoSRemarkUdpPortDscp (1.3.6.1.4.1.25506.2.65.1.12.2.1.5)	read-create	Unsigned32	· 0..63 · 255	DSCP value of matching packets.	As per the MIB.
hh3cQoSRemarkUdpPortRowStatus(1.3.6.1.4.1.25506.2.65.1.12.2.1.6)	read-create	RowStatus	Standard MIB values.	Row status.	· active(1) · createAndGo(4) · destroy(6)

hh3cQoSRemarkIPv4AddrPriTable

About this table

This table contains IPv4 address-based priority information.

Support for operations

Create	Edit/Modify	Delete	Read
Supported	Supported	Supported	Supported

Columns

The table index is hh3cQoSRemarkIPv4AddrValue.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cQoSRemarkIPv4AddrValue (1.3.6.1.4.1.25506.2.65.1.12.3.1.1)	not-accessible	IpAddress	Standard MIB values.	IPv4 address.	As per the MIB.
hh3cQoSRemarkIPv4AddrMask (1.3.6.1.4.1.25506.2.65.1.12.3.1.2)	read-create	IpAddress	Standard MIB values.	Mask for the IPv4 address.	As per the MIB.
hh3cQoSRemarkIPv4AddrMaskLength (1.3.6.1.4.1.25506.2.65.1.12.3.1.3)	read-create	Unsigned32	· 1..32 · 4294967295	Mask length for the IPv4 address	As per the MIB.
hh3cQoSRemarkIPv4AddrDot1p (1.3.6.1.4.1.25506.2.65.1.12.3.1.4)	read-create	Unsigned32	· 0..7 · 255	802.1p priority value of matching packets.	As per the MIB.
hh3cQoSRemarkIPv4AddrDscp (1.3.6.1.4.1.25506.2.65.1.12.3.1.5)	read-create	Unsigned32	· 0..63 · 255	DSCP value of matching packets.	As per the MIB.
hh3cQoSRemarkIPv4AddrRowStatus (1.3.6.1.4.1.25506.2.65.1.12.3.1.6)	read-create	RowStatus	Standard MIB values.	Row status.	· active(1) · createAndGo(4) · destroy(6)

hh3cQoSRemarkIPv6AddrPriTable

About this table

This table contains IPv6 address-based priority information.

Support for operations

Create	Edit/Modify	Delete	Read
Supported	Supported	Supported	Supported

Columns

The table index is hh3cQoSRemarkIPv6AddrValue.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cQoSRemarkIPv6AddrValue (1.3.6.1.4.1.25506.2.65.1.12.4.1.1)	not-accessible	InetAddressIPv6	Standard MIB values.	IPv6 address.	As per the MIB.
hh3cQoSRemarkIPv6AddrPrefixLength (1.3.6.1.4.1.25506.2.65.1.12.4.1.2)	read-create	InetAddressPrefixLength	Standard MIB values.	Prefix length for the IPv6 address.	As per the MIB.
hh3cQoSRemarkIPv6AddrDot1p (1.3.6.1.4.1.25506.2.65.1.12.4.1.3)	read-create	Unsigned32	· 0..7 · 255	802.1p priority value of matching packets.	As per the MIB.
hh3cQoSRemarkIPv6AddrDscp (1.3.6.1.4.1.25506.2.65.1.12.4.1.4)	read-create	Unsigned32	· 0..63 · 255	DSCP value of matching packets.	As per the MIB.
hh3cQoSRemarkIPv6AddrRowStatus (1.3.6.1.4.1.25506.2.65.1.12.4.1.5)	read-create	RowStatus	Standard MIB values.	Row status.	· active(1) · createAndGo(4) · destroy(6)

hh3cQoSRemarkProtocolPriTable

About this table

This table contains Layer 3 protocol-based priority information.

Support for operations

Create	Edit/Modify	Delete	Read
Supported	Supported	Supported	Supported

Columns

The table index is hh3cQoSRemarkProtocolValue.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cQoSRemarkProtocolValue (1.3.6.1.4.1.25506.2.65.1.12.5.1.1)	not-accessible	Integer32	· ip(1) · ipx(2) · arp(3) · appletalk(4) · sna(5) · netbeui(6)	Layer 3 protocol type.	As per the MIB.
hh3cQoSRemarkProtocolDot1p (1.3.6.1.4.1.25506.2.65.1.12.5.1.2)	read-create	Unsigned32	· 0..7 · 255	802.1p priority value of matching packets.	As per the MIB.
hh3cQoSRemarkProtocolRowStatus (1.3.6.1.4.1.25506.2.65.1.12.5.1.3)	read-create	RowStatus	Standard MIB values.	Row status.	· active(1) · createAndGo(4) · destroy(6)

hh3cQoSRemarkVlanPriTable

About this table

This table contains VLAN-based priority information.

Support for operations

Create	Edit/Modify	Delete	Read
Supported	Supported	Supported	Supported

Columns

The table index is hh3cQoSRemarkVlanStart.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cQoSRemarkVlanStart (1.3.6.1.4.1.25506.2.65.1.12.6.1.1)	not-accessible	Ingeter32	1..4094	Start VLAN of a VLAN range.	As per the MIB.
hh3cQoSRemarkVlanEnd (1.3.6.1.4.1.25506.2.65.1.12.6.1.2)	read-create	Ingeter32	1..4094	End VLAN of the VLAN range.	As per the MIB.
hh3cQoSRemarkVlanDot1p (1.3.6.1.4.1.25506.2.65.1.12.6.1.3)	read-create	Unsigned32	· 0..7 · 255	802.1p priority value of matching packets.	As per the MIB.
hh3cQoSRemarkVlanDscp (1.3.6.1.4.1.25506.2.65.1.12.6.1.4)	read-create	Unsigned32	· 0..63 · 255	DSCP value of matching packets.	As per the MIB.
hh3cQoSRemarkVlanRowStatus (1.3.6.1.4.1.25506.2.65.1.12.6.1.5)	read-create	RowStatus	Standard MIB values.	Row status.	· active(1) · createAndGo(4) · destroy(6)

hh3cIfQoSCoppFlowStatTable

About this table

This table contains protocol traffic statistics for a control plane.

Support for operations

Create	Edit/Modify	Delete	Read
Not supported	Not supported	Not supported	Supported

Columns

The table indexes are hh3cIfQoSCoppFlowStatChassis, hh3cIfQoSCoppFlowStatSlot, and hh3cIfQoSCoppFlowStatProType.

Object (OID)	Access	Syntax	Value range	Description	Implementation
hh3cIfQoSCoppFlowStatChassis (1.3.6.1.4.1.25506.2.65.1.14.1.1.1)	not-accessible	Unsigned32	Standard MIB values.	Chassis number for the control plane.	As per the MIB.
hh3cIfQoSCoppFlowStatSlot (1.3.6.1.4.1.25506.2.65.1.14.1.1.2)	not-accessible	Unsigned32	Standard MIB values.	Slot number for the control plane.	As per the MIB.
hh3cIfQoSCoppFlowStatProType (1.3.6.1.4.1.25506.2.65.1.14.1.1.3)	not-accessible	Unsigned32	1..65	Protocol type.	As per the MIB.
hh3cIfQoSCoppFlowPassPackets (1.3.6.1.4.1.25506.2.65.1.14.1.1.4)	read-only	Counter64	Standard MIB values.	Number of forwarded packets.	As per the MIB.
hh3cIfQoSCoppFlowPassBytes (1.3.6.1.4.1.25506.2.65.1.14.1.1.5)	read-only	Counter64	Standard MIB values.	Number of forwarded bytes.	As per the MIB.
hh3cIfQoSCoppFlowDropPackets (1.3.6.1.4.1.25506.2.65.1.14.1.1.6)	read-only	Counter64	Standard MIB values.	Number of dropped packets.	As per the MIB.
hh3cIfQoSCoppFlowDropBytes (1.3.6.1.4.1.25506.2.65.1.14.1.1.7)	read-only	Counter64	Standard MIB values.	Number of dropped bytes.	As per the MIB.

Notifications

The following information describes the notifications included in the HH3C-IFQOS2-MIB module.

hh3cIfQoS8QueueResouceOverAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.1	The downlink resources of an 8-queue scheduling profile are insufficient.	Error	Major	hh3cIfQoS8QueueResouceOverRecover	OFF

Notification triggers

The notification is generated when the downlink (network side to user side) resources of an 8-queue scheduling profile are insufficient.

System impact

The qos user-queue command might not take effect.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCPU (1.3.6.1.4.1.25506.2.65.1.15.3)	CPU number	N/A	Integer32	0 to 65534
hh3cIfQoSChip (1.3.6.1.4.1.25506.2.65.1.15.4)	Chip number	N/A	Integer32	0 to 65534
hh3cIfQoSDirection (1.3.6.1.4.1.25506.2.65.1.15.6)	Direction	N/A	Direction	As per the MIB

Recommended action

To resolve the issue:

1. Delete or optimized related configuration.

2. If you cannot identify the configuration to be deleted or optimized, collect alarm information and configuration data, and then contact H3C Support for help.

hh3cIfQoS8QueueResouceOverRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.2	The resources of an 8-queue user-queue profile are sufficient.	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when the resources of an 8-queue user-queue profile are sufficient.

System impact

No negative impact on the system.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCPU (1.3.6.1.4.1.25506.2.65.1.15.3)	CPU number	N/A	Integer32	0 to 65534
hh3cIfQoSChip (1.3.6.1.4.1.25506.2.65.1.15.4)	Chip number	N/A	Integer32	0 to 65534
hh3cIfQoSDirection (1.3.6.1.4.1.25506.2.65.1.15.6)	Direction	N/A	Direction	As per the MIB

Recommended action

No action is required.

hh3cIfQoS8QueueResoucePreAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.3	The resource usage of an 8-queue scheduling profile exceeds 90%.	Error	Minor	hh3cIfQoS8QueueResoucePreRecover	OFF

Notification triggers

The notification is generated when the resource usage of an 8-queue scheduling profile exceeds 90%.

System impact

No negative impact on the system.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCPU (1.3.6.1.4.1.25506.2.65.1.15.3)	CPU number	N/A	Integer32	0 to 65534
hh3cIfQoSChip (1.3.6.1.4.1.25506.2.65.1.15.4)	Chip number	N/A	Integer32	0 to 65534
hh3cIfQoSDirection (1.3.6.1.4.1.25506.2.65.1.15.6)	Direction	N/A	Direction	As per the MIB

Recommended action

To resolve the issue:

1. Delete or optimized related configuration.

2. If you cannot identify the configuration to be deleted or optimized, collect alarm information and configuration data, and then contact H3C Support for help.

hh3cIfQoS8QueueResoucePreRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.4	The resource usage of an 8-queue scheduling profile fell below 90%.	Recovery	Minor	N/A	OFF

Notification triggers

The notification is generated when the resource usage of an 8-queue scheduling profile falls below 90%.

System impact

No negative impact on the system.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCPU (1.3.6.1.4.1.25506.2.65.1.15.3)	CPU number	N/A	Integer32	0 to 65534
hh3cIfQoSChip (1.3.6.1.4.1.25506.2.65.1.15.4)	Chip number	N/A	Integer32	0 to 65534
hh3cIfQoSDirection (1.3.6.1.4.1.25506.2.65.1.15.6)	Direction	N/A	Direction	As per the MIB

Recommended action

No action is required.

hh3cIfQoSBufferOverAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.5	Queue buffer usage alarm.	Error	Minor	hh3cIfQoSBufferOverRecover	OFF

Notification triggers

An alarm is generated when the queue buffer usage reaches or exceeds 90%.

System impact

Packet loss occurs on high-priority queues.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCPU (1.3.6.1.4.1.25506.2.65.1.15.3)	CPU number	N/A	Integer32	0 to 65534
hh3cIfQoSChip (1.3.6.1.4.1.25506.2.65.1.15.4)	Chip number	N/A	Integer32	0 to 65534
hh3cIfQoSDirection (1.3.6.1.4.1.25506.2.65.1.15.6)	Direction	N/A	Direction	As per the MIB

Recommended action

To resolve the issue:

1. Reduce deployed services.

2. If the issue persists, collect alarm information, log messages, and configuration data, and then contact H3C Support for help.

hh3cIfQoSBufferOverRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.6	Queue buffer usage alarm recovery.	Recovery	Minor	N/A	OFF

Notification triggers

The notification is generated when the queue buffer usage alarm recovers.

System impact

No negative impact on the system.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCPU (1.3.6.1.4.1.25506.2.65.1.15.3)	CPU number	N/A	Integer32	0 to 65534
hh3cIfQoSChip (1.3.6.1.4.1.25506.2.65.1.15.4)	Chip number	N/A	Integer32	0 to 65534

Recommended action

No action is required.

hh3cIfQoSModeChannelOverPortShapAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.7	The channelized bandwidth exceeds the interface rate limit.	Error	Major	hh3cIfQoSModeChannelOverPortShapRecover	OFF

Notification triggers

The notification is generated when the channelized bandwidth exceeds the interface rate limit.

System impact

The channelized bandwidth does not take effect.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCPU (1.3.6.1.4.1.25506.2.65.1.15.3)	CPU number	N/A	Integer32	0 to 65534
hh3cIfQoSIfName (1.3.6.1.4.1.25506.2.65.1.15.5)	Interface name	N/A	OCTET STRING	SIZE (1 to 47)

Recommended action

To resolve the issue:

1. Use the mode channel-bandwidth command to set a smaller channelized bandwidth.

2. If the issue persists, collect alarm information, log messages, and configuration data, and then contact H3C Support for help.

hh3cIfQoSModeChannelOverPortShapRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.8	The channelized bandwidth is smaller than the interface rate limit.	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when the channelized bandwidth is smaller than the interface rate limit.

System impact

No negative impact on the system.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCPU (1.3.6.1.4.1.25506.2.65.1.15.3)	CPU number	N/A	Integer32	0 to 65534
hh3cIfQoSIfName (1.3.6.1.4.1.25506.2.65.1.15.5)	Interface name	N/A	OCTET STRING	SIZE (1 to 47)

Recommended action

No action is required.

hh3cIfQoSExclusiveBandApplyFailAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.9	Exclusive bandwidth application failure alarm.	Error	Major	hh3cIfQoSExclusiveBandApplyFailRecover	OFF

Notification triggers

The notification is generated when the exclusive bandwidth fails to be applied.

System impact

The exclusive bandwidth does not take effect.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCPU (1.3.6.1.4.1.25506.2.65.1.15.3)	CPU number	N/A	Integer32	0 to 65534
hh3cIfQoSIfName (1.3.6.1.4.1.25506.2.65.1.15.5)	Interface name	N/A	OCTET STRING	SIZE (1 to 47)

Recommended action

Collect alarm information and configuration data, and then contact H3C Support for help.

hh3cIfQoSExclusiveBandApplyFailRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.10	Exclusive bandwidth application failure alarm recovery.	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when the exclusive bandwidth application failure alarm recovers.

System impact

No negative impact on the system.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCPU (1.3.6.1.4.1.25506.2.65.1.15.3)	CPU number	N/A	Integer32	0 to 65534
hh3cIfQoSIfName (1.3.6.1.4.1.25506.2.65.1.15.5)	Interface name	N/A	OCTET STRING	SIZE (1 to 47)

Recommended action

No action is required.

hh3cIfQoSExclusiveBandOverAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.11	Exclusive bandwidth exceeding maximum interface bandwidth.	Error	Major	hh3cIfQoSExclusiveBandOverRecover	OFF

Notification triggers

The notification is generated when the exclusive bandwidth value exceeds the maximum interface bandwidth. The configuration will also become ineffective.

System impact

The exclusive bandwidth does not take effect.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCPU (1.3.6.1.4.1.25506.2.65.1.15.3)	CPU number	N/A	Integer32	0 to 65534
hh3cIfQoSIfName (1.3.6.1.4.1.25506.2.65.1.15.5)	Interface name	N/A	OCTET STRING	SIZE (1 to 47)

Recommended action

Configure an exclusive bandwidth value that is smaller than the maximum interface bandwidth.

hh3cIfQoSExclusiveBandOverRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.12	Exclusive bandwidth exceeding maximum interface bandwidth alarm recovery.	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when the alarm that the configured exclusive bandwidth value exceeds the maximum interface bandwidth recovers.

System impact

No negative impact on the system.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCPU (1.3.6.1.4.1.25506.2.65.1.15.3)	CPU number	N/A	Integer32	0 to 65534
hh3cIfQoSIfName (1.3.6.1.4.1.25506.2.65.1.15.5)	Interface name	N/A	OCTET STRING	SIZE (1 to 47)

Recommended action

No action is required.

hh3cIfQoSLRDiscardAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.13	The outgoing traffic of an interface exceeds the configured CIR	Error	Major	hh3cIfQoSLRDiscardAlarmRecover	OFF

Notification triggers

The notification is generated when the outgoing traffic of an interface exceeds the configured CIR.

System impact

The outgoing traffic of an interface might be dropped.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSIfName (1.3.6.1.4.1.25506.2.65.1.15.5)	Interface name	N/A	OCTET STRING	SIZE (1 to 47)
hh3cIfQoSLRCir (1.3.6.1.4.1.25506.2.65.1.3.1.1.2)	CIR	N/A	Unsigned32	Standard MIB values.
hh3cIfQoSPassPacketRate (1.3.6.1.4.1.25506.2.65.1.15.7)	Outgoing traffic rate of the interface	N/A	Unsigned32	Standard MIB values.

Recommended action

Increase the CIR on the interface.

hh3cIfQoSLRDiscardAlarmRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.14	The outgoing traffic rate of an interface drops below the configured CIR	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when the outgoing traffic rate of an interface drops below the configured CIR.

System impact

No negative impact on the system.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSIfName (1.3.6.1.4.1.25506.2.65.1.15.5)	Interface name	N/A	OCTET STRING	SIZE (1 to 47)
hh3cIfQoSLRCir (1.3.6.1.4.1.25506.2.65.1.3.1.1.2)	CIR	N/A	Unsigned32	Standard MIB values.
hh3cIfQoSPassPacketRate (1.3.6.1.4.1.25506.2.65.1.15.7)	Outgoing traffic rate of the interface	N/A	Unsigned32	Standard MIB values.

Recommended action

No action is required.

hh3cIfQoSCarDiscardAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.15	Packets are dropped by CAR on an interface	Error	Major	hh3cIfQoSCarDiscardAlarmRecover	OFF

Notification triggers

The notification is generated when packets are dropped by CAR on an interface.

System impact

Traffic might be dropped.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSIfName (1.3.6.1.4.1.25506.2.65.1.15.5)	Interface name	N/A	OCTET STRING	SIZE (1 to 47)
hh3cIfQoSDirection (1.3.6.1.4.1.25506.2.65.1.15.6)	Direction	N/A	Direction	Standard MIB values.

Recommended action

Cancel the CAR settings or increase the CIR.

hh3cIfQoSCarDiscardAlarmRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.16	Packets dropped by CAR on an interface have been recovered	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when packets dropped by CAR on an interface have been recovered.

System impact

No negative impact on the system.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSIfName (1.3.6.1.4.1.25506.2.65.1.15.5)	Interface name	N/A	OCTET STRING	SIZE (1 to 47)
hh3cIfQoSDirection (1.3.6.1.4.1.25506.2.65.1.15.6)	Direction	N/A	Direction	Standard MIB values.

Recommended action

No action is required.

hh3cIfQoSCoppDropPktAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.17	Packets are dropped by CAR on the control plane	Error	Major	hh3cIfQoSCoppDropPktAlarmRecover	OFF

Notification triggers

The notification is generated when packets are dropped by CAR on the control plane.

System impact

Packets are dropped by CAR on the control plane, and services or internal control information might not be able to be processed.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCoppProtocol (1.3.6.1.4.1.25506.2.65.1.15.8)	Protocol type	N/A	OCTET STRING	SIZE (1 to 31)
hh3cIfQoSBandwidth (1.3.6.1.4.1.25506.2.65.1.15.9)	Bandwidth	N/A	Unsigned32	Standard MIB values.
1.3.6.1.4.1.25506.2.65.1.15.13 (hh3cIfQoSBandwidthUnit)	Bandwidth unit	N/A	INTEGER	· unitUnavailable (0) · unitAbsolute (1) · unitAbsolutePPS (4)

Recommended action

Cancel the CAR settings for the control plane.

hh3cIfQoSCoppDropPktAlarmRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.18	Packets dropped by CAR on the control plane have been recovered	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when packets dropped by CAR on the control plane have been recovered.

System impact

No negative impact on the system.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCoppProtocol (1.3.6.1.4.1.25506.2.65.1.15.8)	Protocol type	N/A	OCTET STRING	SIZE (1 to 31)
hh3cIfQoSBandwidth (1.3.6.1.4.1.25506.2.65.1.15.9)	Bandwidth	N/A	Unsigned32	Standard MIB values.
1.3.6.1.4.1.25506.2.65.1.15.13 (hh3cIfQoSBandwidthUnit)	Bandwidth unit	N/A	INTEGER	· unitUnavailable (0) · unitAbsolute (1) · unitAbsolutePPS (4)

Recommended action

No action is required.

hh3cIfQoSQueExcpAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.19	Packets fail to be forwarded due to queue exceptions.	Error	Major	hh3cIfQoSQueExcpAlarmRecover	OFF

Notification triggers

The notification is generated when packets fail to be forwarded due to queue exceptions.

System impact

Packets cannot be forwarded.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCoppProtocol (1.3.6.1.4.1.25506.2.65.1.15.8)	Protocol type	N/A	OCTET STRING	SIZE (1 to 31)

Recommended action

Collect alarm information and configuration data, and then contact H3C Support for help.

hh3cIfQoSQueExcpAlarmRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.20	Packets failing to be forwarded due to queue exceptions have been recovered.	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when packets failing to be forwarded due to queue exceptions have been recovered.

System impact

No negative impact on the system.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSCoppProtocol (1.3.6.1.4.1.25506.2.65.1.15.8)	Protocol type	N/A	OCTET STRING	SIZE (1 to 31)

Recommended action

No action is required.

hh3cIfQoSBoardL3AclResLack

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.21	Layer 3 ACL resources are insufficient.	Error	Major	N/A	OFF

Notification triggers

The notification is generated when Layer 3 ACL resources are insufficient.

System impact

ACL rules do not take effect or fail to be matched.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSServiceName (1.3.6.1.4.1.25506.2.65.1.15.10)	Service name	N/A	OCTET STRING	SIZE (1 to 63)
hh3cIfQoSFailReason (1.3.6.1.4.1.25506.2.65.1.15.12)	Failure reason	N/A	OCTET STRING	SIZE (1 to 127)

Recommended action

Collect alarm information and configuration data, and then contact H3C Support for help.

hh3cIfQoSAclResAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.22	ACL resources are insufficient.	Error	Major	hh3cIfQoSAclResAlarmRecover	OFF

Notification triggers

The notification is generated when ACL resources are insufficient.

System impact

ACL rules do not take effect or fail to be matched.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSServiceName (1.3.6.1.4.1.25506.2.65.1.15.10)	Service name	N/A	OCTET STRING	SIZE (1 to 63)
hh3cIfQoSApplyObject (1.3.6.1.4.1.25506.2.65.1.15.11)	Application object	N/A	OCTET STRING	SIZE (1 to 127)
hh3cIfQoSDirection (1.3.6.1.4.1.25506.2.65.1.15.6)	Direction	N/A	Direction	Standard MIB values.
hh3cIfQoSFailReason (1.3.6.1.4.1.25506.2.65.1.15.12)	Failure reason	N/A	OCTET STRING	SIZE (1 to 127)

Recommended action

Collect alarm information and configuration data, and then contact H3C Support for help.

hh3cIfQoSAclResAlarmRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.22	The ACL resource alarm is cleared.	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when the ACL resource alarm is cleared.

System impact

No negative impact on the system.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534
hh3cIfQoSServiceName (1.3.6.1.4.1.25506.2.65.1.15.10)	Service name	N/A	OCTET STRING	SIZE (1 to 63)
hh3cIfQoSApplyObject (1.3.6.1.4.1.25506.2.65.1.15.11)	Application object	N/A	OCTET STRING	SIZE (1 to 127)
hh3cIfQoSDirection (1.3.6.1.4.1.25506.2.65.1.15.6)	Direction	N/A	Direction	Standard MIB values.
hh3cIfQoSFailReason (1.3.6.1.4.1.25506.2.65.1.15.12)	Failure reason	N/A	OCTET STRING	SIZE (1 to 127)

Recommended action

No action is required.

hh3cIfQoSAclMemFullAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.24	The ACL forwarding engine memory is exhausted.	Error	Major	hh3cIfQoSAclMemFullAlarmRecover	OFF

Notification triggers

The notification is generated when the ACL forwarding engine memory is exhausted.

System impact

ACL rules fail to be matched.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534

Recommended action

Collect alarm information and configuration data, and then contact H3C Support for help.

hh3cIfQoSAclMemFullAlarmRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.25	The ACL forwarding engine memory is recovered.	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when the ACL forwarding engine memory is recovered.

System impact

No negative impact on the system.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
hh3cIfQoSChassis (1.3.6.1.4.1.25506.2.65.1.15.1)	Chassis number	N/A	Integer32	0 to 65534
hh3cIfQoSSlot (1.3.6.1.4.1.25506.2.65.1.15.2)	Slot number	N/A	Integer32	0 to 65534

Recommended action

No action is required.

hh3cIfQoSBufferAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.26	QoS buffer alarm.	Error	Major	hh3cIfQoSBufferAlarmRecover	OFF

Notification triggers

The notification is generated when buffer resources are insufficient.

System impact

QoS forwarding services are affected.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
1.3.6.1.4.1.25506.2.65.1.15.2 (hh3cIfQoSSlot)	Slot number	N/A	Integer32	0..65534
1.3.6.1.4.1.25506.2.65.1.15.4 (hh3cIfQoSChip)	Chip number	N/A	Integer32	0..65534

Recommended action

Collect alarm information and configuration data, and then contact H3C Support for help.

hh3cIfQoSBufferAlarmRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.27	QoS buffer recovery.	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when buffer resources are sufficient.

System impact

QoS forwarding services are normal.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
1.3.6.1.4.1.25506.2.65.1.15.2 (hh3cIfQoSSlot)	Slot number	N/A	Integer32	0..65534
1.3.6.1.4.1.25506.2.65.1.15.4 (hh3cIfQoSChip)	Chip number	N/A	Integer32	0..65534

Recommended action

No action is required.

hh3cIfQoSQueBufferOverrunAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.28	The buffer usage of a queue reaches the threshold.	Error	Major	hh3cIfQoSQueBufferOverrunRecover	OFF

Notification triggers

The notification is generated when the buffer usage of a queue reaches the threshold.

System impact

Packet loss occurs in the outbound direction.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
1.3.6.1.4.1.25506.2.65.1.15.14 (hh3cIfQoSQueBufferQueID)	Queue ID.	N/A	Integer32	0..65535
1.3.6.1.4.1.25506.2.65.1.15.5 (hh3cIfQoSIfName)	Interface name.	N/A	OCTET STRING	SIZE (1..47)
1.3.6.1.4.1.25506.2.65.1.15.19 (hh3cIfQoSSlot)	Slot number.	N/A	Integer32	0..65534
1.3.6.1.4.1.25506.2.65.1.15.15 (hh3cIfQoSQueBufferUsedCell)	Buffer used during congestion.	N/A	Unsigned32	Standard MIB values.
1.3.6.1.4.1.25506.2.65.1.15.16 (hh3cIfQoSQueBufferUsedLength)	Queue length during congestion.	N/A	Unsigned32	Standard MIB values.
1.3.6.1.4.1.25506.2.65.1.15.17 (hh3cIfQoSQueBufferDiscard)	Packets dropped.	N/A	Counter64	Standard MIB values.

Recommended action

Collect alarm information and configuration data, and then contact H3C Support for help.

hh3cIfQoSQueBufferOverrunRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.29	The buffer usage of a queue falls below the threshold.	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when the buffer usage of a queue falls below the threshold.

System impact

No packets are dropped in the outbound direction.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
1.3.6.1.4.1.25506.2.65.1.15.14 (hh3cIfQoSQueBufferQueID)	Queue ID.	N/A	Integer32	0..65535
1.3.6.1.4.1.25506.2.65.1.15.5 (hh3cIfQoSIfName)	Interface name.	N/A	OCTET STRING	SIZE (1..47)
1.3.6.1.4.1.25506.2.65.1.15.19 (hh3cIfQoSSlot)	Slot number.	N/A	Integer32	0..65534
1.3.6.1.4.1.25506.2.65.1.15.15 (hh3cIfQoSQueBufferUsedCell)	Buffer used during congestion.	N/A	Unsigned32	Standard MIB values.
1.3.6.1.4.1.25506.2.65.1.15.16 (hh3cIfQoSQueBufferUsedLength)	Queue length during congestion.	N/A	Unsigned32	Standard MIB values.
1.3.6.1.4.1.25506.2.65.1.15.17 (hh3cIfQoSQueBufferDiscard)	Packets dropped.	N/A	Counter64	Standard MIB values.

Recommended action

No action is required.

hh3cIfQoSFCoEPriorityAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.30	Priority mapping alarm.	Error	Major	hh3cIfQoSFCoEPriorityRecover	OFF

Notification triggers

The notification is generated when the PHB-to-802.1p priority mapping is disabled in the outbound direction of an interface.

System impact

FCoE packets might be dropped because the priority of FCoE packets is incorrect.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

None.

Recommended action

Collect alarm information and configuration data, and then contact H3C Support for help.

hh3cIfQoSFCoEPriorityRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.31	Priority mapping recovery.	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when the PHB-to-802.1p priority mapping is enabled in the outbound direction of an interface.

System impact

No FCoE packets are dropped due to low priority.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

None.

Recommended action

No action is required.

hh3cIfQoSRcyPortPktsDropAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.32	Packets are dropped on a loopback interface.	Error	Major	hh3cIfQoSRcyPortPktsDropRecover	OFF

Notification triggers

The notification is generated when packets are dropped on a loopback interface.

System impact

Packets are dropped on a loopback interface.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
1.3.6.1.4.1.25506.2.65.1.15.18 (hh3cIfQoSPortID)	Interface ID.	N/A	Integer32	0..65535
1.3.6.1.4.1.25506.2.65.1.15.2 (hh3cIfQoSSlot)	Slot number.	N/A	Integer32	0..65534
1.3.6.1.4.1.25506.2.65.1.15.4 (hh3cIfQoSChip)	Chip number.	N/A	Integer32	0..65534

Recommended action

Collect alarm information and configuration data, and then contact H3C Support for help.

hh3cIfQoSRcyPortPktsDropRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.33	Packets are no longer dropped on a loopback interface.	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when packets are no longer dropped on a loopback interface.

System impact

Packets are no longer dropped on a loopback interface.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
1.3.6.1.4.1.25506.2.65.1.15.18 (hh3cIfQoSPortID)	Interface ID.	N/A	Integer32	0..65535
1.3.6.1.4.1.25506.2.65.1.15.2 (hh3cIfQoSSlot)	Slot number.	N/A	Integer32	0..65534
1.3.6.1.4.1.25506.2.65.1.15.4 (hh3cIfQoSChip)	Chip number.	N/A	Integer32	0..65534

Recommended action

No action is required.

hh3cIfQoSStormSuppressAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.34	QoS storm suppression alarm.	Error	Major	hh3cIfQoSStormSuppressRecover	OFF

Notification triggers

The notification is generated when the QoS storm suppression feature is abnormal.

System impact

The QoS storm suppression feature is abnormal.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
1.3.6.1.4.1.25506.2.65.1.15.2 (hh3cIfQoSSlot)	Slot number.	N/A	Integer32	0..65534

Recommended action

Collect alarm information and configuration data, and then contact H3C Support for help.

hh3cIfQoSStormSuppressRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.35	QoS storm suppression alarm.	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when the QoS storm suppression feature is normal.

System impact

The QoS storm suppression feature is normal.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
1.3.6.1.4.1.25506.2.65.1.15.2 (hh3cIfQoSSlot)	Slot number.	N/A	Integer32	0..65534

Recommended action

No action is required.

hh3cIfQoSUniPktsDiscardAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.36	Unicast packets are dropped.	Error	Major	hh3cIfQoSUniPktsDiscardRecover	OFF

Notification triggers

The notification is generated when unicast packets are dropped.

System impact

Unicast packets are dropped.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
1.3.6.1.4.1.25506.2.65.1.15.2 (hh3cIfQoSSlot)	Slot number.	N/A	Integer32	0..65534

Recommended action

Collect alarm information and configuration data, and then contact H3C Support for help.

hh3cIfQoSUniPktsDiscardRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.37	Unicast packets are no longer dropped.	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when unicast packets are no longer dropped.

System impact

Unicast packets are no longer dropped.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
1.3.6.1.4.1.25506.2.65.1.15.2 (hh3cIfQoSSlot)	Slot number.	N/A	Integer32	0..65534

Recommended action

No action is required.

hh3cIfQoSIngressDiscardAlarm

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.38	Packet scheduling in the inbound direction fails.	Error	Major	hh3cIfQoSIngressDiscardRecover	OFF

Notification triggers

The notification is generated when packet scheduling in the inbound direction fails.

System impact

Packet scheduling in the inbound direction fails.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
1.3.6.1.4.1.25506.2.65.1.15.2 (hh3cIfQoSSlot)	Slot number.	N/A	Integer32	0..65534

Recommended action

Collect alarm information and configuration data, and then contact H3C Support for help.

hh3cIfQoSIngressDiscardRecover

Basic information

OID	Event	Type	Severity	Recovery notification	Default status
1.3.6.1.4.1.25506.2.65.1.16.0.39	Packet scheduling in the inbound direction succeeds.	Recovery	Major	N/A	OFF

Notification triggers

The notification is generated when packet scheduling in the inbound direction succeeds.

System impact

Packet scheduling in the inbound direction succeeds.

Status control

ON

· CLI: Use the snmp-agent trap enable qos command.

OFF

· CLI: Use the undo snmp-agent trap enable qos command.

Objects

OID (object name)	Description	Index nodes	Type	Value range
1.3.6.1.4.1.25506.2.65.1.15.2 (hh3cIfQoSSlot)	Slot number.	N/A	Integer32	0..65534

Recommended action

No action is required.

13-ACL and QoS

WRED

Aggregate CAR

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations

Columns

About this table

Support for operations