verbose: Displays detailed information about Layer 3 interfaces. If you do not specify this keyword, the command displays brief information about Layer 3 interfaces.

Usage guidelines

If you do not specify any parameters, this command displays brief L2VPN information for all Layer 3 interfaces that are mapped to VSIs.

Examples

# Display brief L2VPN information for all Layer 3 interfaces that are mapped to VSIs.

<Sysname> display l2vpn interface

Total number of interfaces: 2, 1 up, 1 down

Interface Owner Link ID State Type

GE1/0/1 vxlan3 1 Up VSI

GE1/0/2 vxlan4 2 Down VSI

Table 1 Command output

Field	Description
Interface	Layer 3 interface name.
Owner	VSI name.
Link ID	The interface's link ID on the VSI.
State	Physical state of the interface: · Up—The interface is physically up. · Down—The interface is physically down.
Type	L2VPN type of the interface. This field displays VSI for the VXLAN feature.

# Display detailed L2VPN information for all Layer 3 interfaces that are mapped to VSIs.

<Sysname> display l2vpn interface verbose

Interface: GE1/0/1

Owner : vsi1

Link ID : 0

State : Up

Type : VSI

E-Tree Mode : root

AC VNID : -

End.Dx2 SID : -

End.Dx2l SID : -

Interface: GE1/0/2

Owner : vsi2

Link ID : 0

State : Down

Type : VSI

E-Tree Mode : root

AC VNID : -

End.Dx2 SID : -

End.Dx2l SID : -

Table 2 Command output

Field	Description
Interface	Layer 3 interface name.
Owner	VSI name.
Link ID	The interface's link ID on the VSI.
State	Physical state of the interface: · Up—The interface is physically up. · Down—The interface is physically down.
Type	L2VPN type of the interface. This field displays VSI for the VXLAN feature.
E-Tree Mode	Role of the AC in EVPN E-tree in the EVPN VPLS or EVPN VPLS over SRv6 network: · root. · leaf.
AC VNID	Virtual nexthop for the AC. This field is available only when AC bypass is configured for the AC.
End.Dx2 SID	This field is not supported in the current software version. End.DX2 SID assigned to the AC in the EVPN VPLS over SRv6 network. This field displays a hyphen (-) if the AC is not assigned any End.DX2 SID.
End.Dx2l SID	This field is not supported in the current software version. End.Dx2l SID assigned to the AC in the EVPN VPLS over SRv6 network. This field displays a hyphen (-) if the AC is not assigned any End.Dx2l SID.

Related commands

display l2vpn service-instance

Field	Description
State	Entry state: Dynamic—Local- or remote-MAC entry dynamically learned in the data plane.
Link ID/Name	For a local MAC address, this field displays the AC's link ID on the VSI. For a remote MAC address, this field displays the tunnel interface name.
Aging	Entry aging state: · Aging. · NotAging.

Use display l2vpn service-instance to display information about Ethernet service instances.

Syntax

display l2vpn service-instance [ interface interface-type interface-number [ service-instance instance-id ] ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

Parameters

interface interface-type interface-number: Specifies a Layer 2 Ethernet interface or Layer 2 aggregate interface by its interface type and number. If you do not specify an interface, this command displays Ethernet service instance information for all Layer 2 Ethernet interfaces and Layer 2 aggregate interfaces.

service-instance instance-id: Specifies an Ethernet service instance by its ID in the range of 1 to 4096. If you do not specify an Ethernet service instance, this command displays information about all Ethernet service instances on the specified Layer 2 Ethernet interface or Layer 2 aggregate interface.

verbose: Displays detailed information about Ethernet service instances. If you do not specify this keyword, the command displays brief information about Ethernet service instances.

Examples

# Display brief information about all Ethernet service instances.

<Sysname> display l2vpn service-instance

Total number of service-instances: 4, 4 up, 0 down

Total number of ACs: 2, 2 up, 0 down

Interface SrvID Owner LinkID State Type

GE1/0/1 3 vsi12 1 Up VSI

GE1/0/1 4 vsi13 1 Up VSI

Table 4 Command output

Field	Description
Total number of ACs	Total number of attachment circuits (ACs) and the number of ACs in each state (up or down).
Interface	Name of a Layer 2 Ethernet interface or Layer 2 aggregate interface.
SrvID	Ethernet service instance ID.
Owner	VSI name. This field is empty if an Ethernet service instance is not mapped to any VSI.
LinkID	Ethernet service instance's link ID on the VSI.
State	Ethernet service instance state: · Up. · Down.
Type	L2VPN type of the Ethernet service instance: · VSI. · VPWS.

# Display detailed information about all Ethernet service instances on GigabitEthernet 1/0/1.

<Sysname> display l2vpn service-instance interface gigabitethernet 1/0/1 verbose

Interface: GE1/0/1

Service Instance : 1

Encapsulation : s-vid 16

VSI Name : vsi10

Link ID : 1

State : Up

E-Tree Mode : root

AC VNID : -

End.DX2 SID : -

End.DX2l SID : -

Table 5 Command output

Field	Description
Interface	Name of a Layer 2 Ethernet interface or Layer 2 aggregate interface.
Service Instance	Ethernet service instance ID.
Encapsulation	Frame match criterion of the Ethernet service instance. If the Ethernet service instance does not contain a match criterion, the command does not display this field.
Link ID	Ethernet service instance's link ID on the VSI.
State	Ethernet service instance state: · Up. · Down.
E-Tree Mode	Role of the AC in EVPN E-tree in the EVPN VPLS or EVPN VPLS over SRv6 network: · root. · leaf.
AC VNID	ID of the virtual next hop for the AC. This field is displayed only when the AC is configured with an AC bypass.
End.Dx2 SID	This field is not supported in the current software version. End.DX2 SID assigned to the AC in the EVPN VPLS over SRv6 network. This field displays a hyphen (-) if the AC is not assigned any End.DX2 SID.
End.Dx2l SID	This field is not supported in the current software version. End.Dx2l SID assigned to the AC in the EVPN VPLS over SRv6 network. This field displays a hyphen (-) if the AC is not assigned any End.Dx2l SID.

Related commands

service-instance

display l2vpn vsi

Use display l2vpn vsi to display information about VSIs.

Syntax

display l2vpn vsi [ name vsi-name ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

Parameters

name vsi-name: Specifies a VSI by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command displays information about all VSIs.

verbose: Displays detailed information about VSIs. If you do not specify this keyword, the command displays brief information about VSIs.

Examples

# Display brief information about all VSIs.

<Sysname> display l2vpn vsi

Total number of VSIs: 1, 1 up, 0 down, 0 admin down

VSI Name VSI Index MTU State

vpna 0 1500 Up

Table 6 Command output

Field	Description
MTU	MTU on the VSI.
State	VSI state: · Up—The VSI is up. · Down—The VSI is down. · Admin down—The VSI has been manually shut down by using the shutdown command.

Field

Description

MTU

MTU on the VSI.

State

VSI state:

· Up—The VSI is up.

· Down—The VSI is down.

· Admin down—The VSI has been manually shut down by using the shutdown command.

# Display detailed information about all VSIs.

<Sysname> display l2vpn vsi verbose

VSI Name: vpna

VSI Index : 0

VSI State : Up

MTU : 1500

Bandwidth : -

Broadcast Restrain : -

Multicast Restrain : -

Unknown Unicast Restrain: -

MAC Learning : Enabled

MAC Table Limit : -

MAC Learning rate : -

Drop Unknown : -

PW Redundancy : Slave

VXLAN ID : 10

Tunnels:

Tunnel Name Link ID State Type Flood Proxy Split horizon

Tunnel1 0x5000001 Up Manual Disabled Enabled

Tunnel2 0x5000002 Up Manual Disabled Enabled

ACs:

AC Link ID State

GE1/0/1 0 Up

Table 7 Command output

Field	Description
VSI Description	Description of the VSI. If the VSI does not have a description, the command does not display this field.
VSI State	VSI state: · Up—The VSI is up. · Down—The VSI is down. · Administratively down—The VSI has been manually shut down by using the shutdown command.
MTU	MTU on the VSI.
Bandwidth	Maximum bandwidth (in kbps) for known unicast traffic on the VSI. This field displays a hyphen (-) if it is not available in the current software version.
Broadcast Restrain	Broadcast restraint bandwidth (in kbps). This field displays a hyphen (-) if it is not available in the current software version.
Multicast Restrain	Multicast restraint bandwidth (in kbps). This field displays a hyphen (-) if it is not available in the current software version.
Unknown Unicast Restrain	Unknown unicast restraint bandwidth (in kbps). This field displays a hyphen (-) if it is not available in the current software version.
MAC Learning	State of the MAC learning feature.
MAC Table Limit	Maximum number of MAC address entries on the VSI. This field displays a hyphen (-) if it is not available in the current software version.
MAC Learning Rate	This field is not supported in the current software version. MAC address entry learning rate of the VSI.
Drop Unknown	Action on source MAC-unknown frames received after the maximum number of MAC entries is reached.
State	Tunnel state: · Up—The tunnel is operating correctly. · Blocked—The tunnel is a backup proxy tunnel. Its tunnel interface is up, but the tunnel is blocked because the primary proxy tunnel is operating correctly. ‌ · Defect—The tunnel interface is up, but BFD cannot detect the remote VTEP. This state is not supported in the current software version. · Down—The tunnel interface is down.
Type	Tunnel assignment method: Manual—The tunnel was manually assigned to the VXLAN.
Flood Proxy	Flood proxy state: · Enabled—Flood proxy is enabled. The VTEP sends broadcast, multicast, and unknown unicast traffic to a flood proxy server through the tunnel. The flood proxy server replicates and forwards flood traffic to remote VTEPs. · Disabled—Flood proxy is disabled.
Split horizon	State of split horizon: · Enabled—Split horizon is enabled on the VXLAN tunnel. The VXLAN tunnel does not forward the traffic that is received on other VXLAN tunnels. · Disabled—Split horizon is disabled on the VXLAN tunnel. The VXLAN tunnel forwards the traffic that is received on other VXLAN tunnels.
ACs	ACs that are bound to the VSI.
Link ID	AC's link ID on the VSI.
State	AC state: · Up. · Down.

display vxlan tunnel

Use display vxlan tunnel to display VXLAN tunnel information for VXLANs.

Syntax

display vxlan tunnel [ vxlan-id vxlan-id [ tunnel tunnel-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

Parameters

vxlan-id: Specifies a VXLAN ID in the range of 0 to 16777215. If you do not specify a VXLAN, this command displays VXLAN tunnel information for all VXLANs.

tunnel tunnel-number: Specifies a VXLAN tunnel. The tunnel-number argument represents the tunnel interface number. The value range for the tunnel-number argument is 0 to 65534. If you do not specify a VXLAN tunnel, this command displays information about all VXLAN tunnels associated with the specified VXLAN.

Examples

# Display VXLAN tunnel information for all VXLANs.

<Sysname> display vxlan tunnel

Total number of VXLANs: 1

VXLAN ID: 10, VSI name: vpna, Total tunnels: 3 (3 up, 0 down, 0 defect, 0 blocked)

Tunnel name Link ID State Type Flood proxy Split horizon

Tunnel1 0x5000001 Up Manual Disabled Enabled

Tunnel2 0x5000002 Up Manual Disabled Enabled

# Display VXLAN tunnel information for VXLAN 10.

<Sysname> display vxlan tunnel vxlan-id 10

VXLAN ID: 10, VSI name: vpna, Total tunnels: 3 (3 up, 0 down, 0 defect, 0 blocked)

Tunnel name Link ID State Type Flood proxy Split horizon

Tunnel1 0x5000001 Up Manual Disabled Enabled

Tunnel2 0x5000002 Up Manual Disabled Enabled

# Display information about VXLAN tunnel 0 for VXLAN 10.

<Sysname> display vxlan tunnel vxlan-id 10 tunnel 0

Interface: Tunnel0

Link ID : 0x5000000

State : Up

Type : Manual

Flood Proxy : Disabled

Split horizon : Enabled

Table 8 Command output

Field	Description
Link ID	Tunnel's link ID in the VXLAN.
State	Tunnel state: · Up—The tunnel is operating correctly. · Blocked—The tunnel is a backup proxy tunnel. Its tunnel interface is up, but the tunnel is blocked because the primary proxy tunnel is operating correctly. ‌ · Defect—The tunnel interface is up, but BFD cannot detect the remote VTEP. This state is not supported in the current software version. · Down—The tunnel interface is down.
Type	Tunnel assignment method: Manual—The tunnel was manually assigned to the VXLAN.
Flood proxy	Flood proxy state: · Enabled—Flood proxy is enabled. The VTEP sends broadcast, multicast, and unknown unicast traffic to a flood proxy server through the tunnel. The flood proxy server replicates and forwards flood traffic to remote VTEPs. · Disabled—Flood proxy is disabled.
Split horizon	State of split horizon: · Enabled—Split horizon is enabled on the VXLAN tunnel. The VXLAN tunnel does not forward the traffic that is received on other VXLAN tunnels. · Disabled—Split horizon is disabled on the VXLAN tunnel. The VXLAN tunnel forwards the traffic that is received on other VXLAN tunnels.

‌

Related commands

tunnel

vxlan

encapsulation

Use encapsulation to configure a frame match criterion for an Ethernet service instance.

Use undo encapsulation to restore the default.

Syntax

encapsulation s-vid vlan-id-list [ only-tagged ]

encapsulation { default | tagged | untagged }

undo encapsulation

Default

An Ethernet service instance does not contain a frame match criterion.

Views

Ethernet service instance view

Predefined user roles

network-admin

context-admin

Parameters

s-vid: Matches frames that are tagged with the specified outer 802.1Q VLAN IDs.

vlan-id: Specifies an 802.1Q VLAN ID in the range of 1 to 4094.

vlan-id-list: Specifies a space-separated list of up to eight VLAN items. Each item specifies a VLAN ID or a range of VLAN IDs in the format of vlan-id1 to vlan-id2. The value range for VLAN IDs is 1 to 4094.

only-tagged: Matches tagged frames. If the outer 802.1Q VLAN is not the PVID, the matching result does not differ, whether or not you specify the only-tagged keyword. If the outer 802.1Q VLAN is the PVID, the matching result depends on whether or not the only-tagged keyword is specified.

· To match only PVID-tagged frames, specify the only-tagged keyword.

· To match both untagged frames and PVID-tagged frames, do not specify the only-tagged keyword.

default: Matches frames that do not match any other Ethernet service instance on the interface. On an interface, you can configure this criterion only in one Ethernet service instance. The Ethernet service instance matches any frames if it is the only instance on the interface.

tagged: Matches any frames that have an 802.1Q VLAN tag.

untagged: Matches any frames that do not have an 802.1Q VLAN tag.

Usage guidelines

An Ethernet service instance can contain only one match criterion. To change the match criterion, first execute the undo encapsulation command to remove the original criterion. When you remove the match criterion in an Ethernet service instance, the mapping between the service instance and the VSI is removed automatically.

Examples

# Configure Ethernet service instance 1 on GigabitEthernet 1/0/1 to match frames that have an outer 802.1Q VLAN ID of 111.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] service-instance 1

[Sysname-GigabitEthernet1/0/1-srv1] encapsulation s-vid 111

Related commands

display l2vpn service-instance

l2vpn enable

Use l2vpn enable to enable L2VPN.

Use undo l2vpn enable to disable L2VPN.

Syntax

l2vpn enable

undo l2vpn enable

Default

L2VPN is disabled.

Views

System view

Predefined user roles

network-admin

context-admin

Usage guidelines

You must enable L2VPN before you can configure L2VPN settings.

Examples

# Enable L2VPN.

<Sysname> system-view

[Sysname] l2vpn enable

mtu

Use mtu to set the MTU for a VSI.

Use undo mtu to restore the default.

Syntax

mtu size

undo mtu

Default

The default MTU of a VSI is 1500 bytes.

Views

VSI view

Predefined user roles

network-admin

context-admin

Parameters

size: Specifies an MTU value. The value range for this argument is 300 to 65535.

Usage guidelines

The MTU set by using this command limits the maximum length of the packets that a VSI receives from ACs and forwards through VXLAN tunnels. The MTU does not limit the maximum length of other packets in the VXLAN VSI.

Fragmentation is disabled for a VSI that uses the default MTU. If you set a MTU for a VSI, the packets longer than the MTU are fragmented.

Examples

# Set the MTU to 1400 bytes for VSI vxlan1.

<Sysname> system-view

[Sysname] vsi vxlan1

[Sysname-vsi-vxlan1] mtu 1400

Related commands

display l2vpn vsi

reset l2vpn mac-address

Use reset l2vpn mac-address to clear dynamic MAC address entries on VSIs.

Syntax

reset l2vpn mac-address [ vsi vsi-name ]

Views

User view

Predefined user roles

network-admin

context-admin

Parameters

vsi vsi-name: Specifies a VSI by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command clears all dynamic MAC address entries on all VSIs.

Usage guidelines

Use this command when the number of dynamic MAC address entries reaches the limit or the device learns incorrect MAC addresses.

Examples

# Clear the dynamic MAC address entries on VSI vpn1.

<Sysname> reset l2vpn mac-address vsi vpn1

Related commands

display l2vpn mac-address vsi

service-instance

Use service-instance to create an Ethernet service instance and enter its view, or enter the view of an existing Ethernet service instance.

Use undo service-instance to delete an Ethernet service instance.

Syntax

service-instance instance-id

undo service-instance instance-id

Default

No Ethernet service instances exist.

Views

Layer 2 aggregate interface view

Layer 2 Ethernet interface view

Predefined user roles

network-admin

context-admin

Parameters

instance-id: Specifies an Ethernet service instance ID in the range of 1 to 4096.

Examples

# On Layer 2 Ethernet interface GigabitEthernet 1/0/1, create Ethernet service instance 1 and enter Ethernet service instance view.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] service-instance 1

[Sysname-GigabitEthernet1/0/1-srv1]

Related commands

display l2vpn service-instance

shutdown

Use shutdown to shut down a VSI.

Use undo shutdown to bring up a VSI.

Syntax

shutdown

undo shutdown

Default

VSIs are not manually shut down.

Views

VSI view

Predefined user roles

network-admin

context-admin

Usage guidelines

Use this command to temporarily disable a VSI to provide Layer 2 switching services. The shutdown action does not change settings on the VSI. You can continue to configure the VSI. After you bring up the VSI again, the VSI provides services based on the latest settings.

Examples

# Shut down VSI vpn1.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] shutdown

Related commands

display l2vpn vsi

statistics enable (tunnel interface view)

Use statistics enable to enable packet statistics for a manually created VXLAN or VXLAN-DCI tunnel.

Use undo statistics enable to disable packet statistics for a manually created VXLAN or VXLAN-DCI tunnel.

Syntax

statistics enable

undo statistics enable

Default

The packet statistics feature is disabled for a manually created VXLAN or VXLAN-DCI tunnel.

Views

VXLAN tunnel interface view

VXLAN-DCI tunnel interface view

Predefined user roles

network-admin

context-admin

Examples

# Enable packet statistics for VXLAN tunnel interface Tunnel 0.

<Sysname> system-view

[Sysname] interface tunnel 0 mode vxlan

[Sysname-Tunnel0] statistics enable

Related commands

display interface tunnel (Layer 3—IP Services Command Reference)

reset counters interface tunnel (Layer 3—IP Services Command Reference)

tunnel statistics vxlan auto

tunnel

Use tunnel to assign a VXLAN tunnel to a VXLAN.

Use undo tunnel to remove a VXLAN tunnel from a VXLAN.

Syntax

tunnel tunnel-number [ flooding-proxy ]

undo tunnel tunnel-number

Default

A VXLAN does not contain VXLAN tunnels.

Views

VXLAN view

Predefined user roles

network-admin

context-admin

Parameters

tunnel-number: Specifies a tunnel interface number. The value range for this argument is 0 to 1023. The tunnel must be a VXLAN tunnel.

flooding-proxy: Enables flood proxy on the tunnel for the VTEP to send flood traffic to the flood proxy server. The flood proxy server replicates and forwards flood traffic to remote VTEPs. If you do not specify this keyword, flood proxy is disabled on the tunnel.

remote-vni vxlan-id: Specifies a remote VXLAN ID. The value range for the vxlan-id argument varies by device model. You can specify this option only for a VXLAN-DCI tunnel.

Usage guidelines

This command assigns a VXLAN tunnel to a VXLAN to provide Layer 2 connectivity for the VXLAN between two sites. In unicast mode, the system floods unknown unicast, multicast, and broadcast traffic to each tunnel in the VXLAN.

You can assign multiple VXLAN tunnels to a VXLAN, and configure a VXLAN tunnel to trunk multiple VXLANs.

On a VSI, you can enable flood proxy on multiple VXLAN tunnels. The first tunnel that is enabled with flood proxy works as the primary proxy tunnel to forward broadcast, multicast, and unknown unicast traffic. Other proxy tunnels are backups that do not forward traffic when the primary proxy tunnel is operating correctly.

To modify the flood proxy setting on a VXLAN tunnel, you must first use the undo tunnel command to remove the tunnel.

Examples

# Assign VXLAN tunnels 1 and 2 to VXLAN 10000.

<Sysname> system-view

[Sysname] vsi vpna

[Sysname-vsi-vpna] vxlan 10000

[Sysname-vsi-vpna-vxlan-10000] tunnel 1

[Sysname-vsi-vpna-vxlan-10000] tunnel 2

Related commands

display vxlan tunnel

tunnel global source-address

Use tunnel global source-address to specify a global source address for VXLAN tunnels.

Use undo tunnel global source-address to restore the default.

Syntax

tunnel global source-address { ipv4-address | ipv6 ipv6-address }

undo tunnel global source-address [ ipv6 ]

Default

No global source address is specified for VXLAN tunnels.

Views

System view

Predefined user roles

network-admin

context-admin

Parameters

ipv4-address: Specifies an IPv4 address.

ipv6 ipv6-address: Specifies an IPv6 address. If you do not specify the ipv6 keyword when executing the undo tunnel global source-address command, the command deletes the global source IPv4 address for VXLAN tunnels.

Usage guidelines

A VXLAN tunnel uses the global source address if you do not specify a source interface or source address for the tunnel.

The global source address takes effect only on VXLAN tunnels.

IPv4 VXLAN tunnels use the global source IPv4 address, and IPv6 VXLAN tunnels use the global source IPv6 addresses.

Examples

# Specify 1.1.1.1 as the global source address for VXLAN tunnels.

<Sysname> system-view

[Sysname] tunnel global source-address 1.1.1.1

vsi

Use vsi to create a VSI and enter its view, or enter the view of an existing VSI.

Use undo vsi to delete a VSI.

Syntax

vsi vsi-name

undo vsi vsi-name

Default

No VSIs exist.

Views

System view

Predefined user roles

network-admin

context-admin

Parameters

vsi-name: Specifies a VSI name, a case-sensitive string of 1 to 31 characters.

Usage guidelines

A VSI acts as a virtual switch to provide Layer 2 switching services for a VXLAN on a VTEP. A VSI has all functions of a physical Ethernet switch, including source MAC address learning, MAC address aging, and flooding.

A VSI can provide services only for one VXLAN.

Examples

# Create VSI vxlan10 and enter VSI view.

<Sysname> system-view

[Sysname] vsi vxlan10

[Sysname-vsi-vxlan10]

Related commands

display l2vpn vsi

vxlan

Use vxlan to create a VXLAN and enter its view, or enter the view of an existing VXLAN.

Use undo vxlan to restore the default.

Syntax

vxlan vxlan-id

undo vxlan

Default

No VXLANs exist.

Views

VSI view

Predefined user roles

network-admin

context-admin

Parameters

vxlan-id: Specifies a VXLAN ID in the range of 0 to 16777215.

Usage guidelines

You can create only one VXLAN for a VSI. The VXLAN ID for each VSI must be unique.

Examples

# Create VXLAN 10000 for VSI vpna and enter VXLAN view.

<Sysname> system-view

[Sysname] vsi vpna

[Sysname-vsi-vpna] vxlan 10000

[Sysname-vsi-vpna-vxlan-10000]

Related commands

vsi

vxlan fast-forwarding enable

Use vxlan fast-forwarding enable to enable VXLAN fast forwarding.

Use undo vxlan fast-forwarding enable to disable VXLAN fast forwarding.

Syntax

vxlan fast-forwarding enable

undo vxlan fast-forwarding enable

Default

VXLAN fast forwarding is disabled.

Views

System view

Predefined user roles

network-admin

context-admin

Usage guidelines

VXLAN fast forwarding enables the device to bypass QoS and security services when the device forwards data traffic over VXLAN tunnels based on the software. As a best practice, enable this feature to improve forwarding speed only when QoS and security services are not configured on the following interfaces:

· VSI interfaces.

· Traffic outgoing interfaces for VXLAN tunnels.

When VXLAN fast forwarding is enabled, a VXLAN tunnel cannot use ECMP routes to load share traffic. Instead, it selects one route from the ECMP routes to forward VXLAN packets.

Examples

# Enable VXLAN fast forwarding.

<Sysname> system

[Sysname] vxlan fast-forwarding enable

vxlan invalid-udp-checksum discard

Use vxlan invalid-udp-checksum discard to enable the device to drop the VXLAN packets that fail UDP checksum check.

Use undo vxlan invalid-udp-checksum discard to restore the default.

Syntax

vxlan invalid-udp-checksum discard

undo vxlan invalid-udp-checksum discard

Default

The device does not check the UDP checksum of VXLAN packets.

Views

System view

Predefined user roles

network-admin

context-admin

Usage guidelines

This command enables the device to check the UDP checksum of VXLAN packets.

The device always sets the UDP checksum of VXLAN packets to 0. For compatibility with third-party devices, a VXLAN packet can pass the check if its UDP checksum is 0 or correct. If its UDP checksum is incorrect, the VXLAN packet fails the check and is dropped.

Examples

# Enable the device to drop the VXLAN packets that fail UDP checksum check.

<Sysname> system-view

[Sysname] vxlan invalid-udp-checksum discard

vxlan udp-port

Use vxlan udp-port to set the destination UDP port number for VXLAN packets.

Use undo vxlan udp-port to restore the default.

Syntax

vxlan udp-port port-number

undo vxlan udp-port

Default

The destination UDP port number is 4789 for VXLAN packets.

Views

System view

Predefined user roles

network-admin

context-admin

Parameters

port-number: Specifies a UDP port number in the range of 1 to 65535. As a best practice, specify a port number in the range of 1024 to 65535 to avoid conflict with well-known ports.

Usage guidelines

You must configure the same destination UDP port number on all VTEPs in a VXLAN.

Examples

# Set the destination UDP port number to 6666 for VXLAN packets.

<Sysname> system-view

[Sysname] vxlan udp-port 6666

xconnect vsi

Use xconnect vsi to map an AC to a VSI.

Use undo xconnect vsi to restore the default.

Syntax

xconnect vsi vsi-name [ access-mode { ethernet | vlan } ] [ track track-entry-number&<1-3> ]

undo xconnect vsi

Default

An AC is not mapped to any VSI.

Views

Ethernet service instance view

Interface view

Predefined user roles

network-admin

context-admin

Parameters

vsi-name: Specifies the VSI name, a case-sensitive string of 1 to 31 characters.

access-mode: Specifies an access mode. If the AC is an Ethernet service instance or Layer 3 subinterface, you can specify this keyword. The default access mode is VLAN. If the AC is a Layer 3 interface, you cannot specify this keyword.

ethernet: Specifies the Ethernet access mode.

vlan: Specifies the VLAN access mode.

track track-entry-number&<1-3>: Specifies a space-separated list of up to three track entry numbers in the range of 1 to 1024. The AC is up only if a minimum of one associated track entry is in positive state.

Usage guidelines

For traffic that matches a Layer 3 interface, the system uses the VSI's MAC address table to make a forwarding decision.

For traffic that matches an Ethernet service instance on an interface, the system uses the VSI's MAC address table to make a forwarding decision.

To execute this command for an Ethernet service instance, you must first use the encapsulation command to add a traffic match criterion to the service instance.

The access mode determines how a VTEP processes the 802.1Q VLAN tags in the inner Ethernet frames assigned to the VSI.

· VLAN access mode—Ethernet frames received from or sent to the local site must contain 802.1Q VLAN tags.

¡ For an Ethernet frame received from the local site, the VTEP removes all its 802.1Q VLAN tags before forwarding the frame.

¡ For an Ethernet frame destined for the local site, the VTEP adds 802.1Q VLAN tags to the frame before forwarding the frame.

In VLAN access mode, VXLAN packets sent between VXLAN sites do not contain 802.1Q VLAN tags. VXLAN can provide Layer 2 connectivity for different 802.1Q VLANs between sites. You can use different 802.1Q VLANs to provide the same service in different sites.

· Ethernet access mode—The VTEP does not process the 802.1Q VLAN tags of Ethernet frames received from or sent to the local site.

¡ For an Ethernet frame received from the local site, the VTEP forwards the frame with the 802.1Q VLAN tags intact.

¡ For an Ethernet frame destined for the local site, the VTEP forwards the frame without adding 802.1Q VLAN tags.

In Ethernet access mode, VXLAN packets sent between VXLAN sites contain 802.1Q VLAN tags. VXLAN cannot provide Layer 2 connectivity for different 802.1Q VLANs between sites. You must use the same 802.1Q VLAN to provide the same service between sites.

After you modify the access mode on a Layer 3 subinterface AC, local VMs that access the VXLAN network through the subinterface cannot communicate with remote VMs. To resolve this issue, you must clear the ARP entries on the local VMs or configure them to periodically send gratuitous ARP packets.

Examples

# Map GigabitEthernet 1/0/1 to VSI vpn1.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] quit

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] xconnect vsi vpn1

Related commands

display l2vpn interface

display l2vpn service-instance

encapsulation

vsi

VXLAN IP gateway commands

arp distributed-gateway dynamic-entry synchronize

Use arp distributed-gateway dynamic-entry synchronize to enable dynamic ARP entry synchronization for distributed VXLAN IP gateways.

Use undo arp distributed-gateway dynamic-entry synchronize to disable dynamic ARP entry synchronization for distributed VXLAN IP gateways.

Syntax

arp distributed-gateway dynamic-entry synchronize

undo arp distributed-gateway dynamic-entry synchronize

Default

Dynamic ARP entry synchronization is disabled for distributed VXLAN IP gateways.

Views

System view

Predefined user roles

network-admin

context-admin

Usage guidelines

When local proxy ARP is enabled on distributed VXLAN IP gateways, each gateway learns ARP information independently. A gateway does not forward ARP packets destined for its local VSI interfaces to other gateways. For distributed VXLAN IP gateways to have the same ARP entries, you must enable dynamic ARP entry synchronization.

A controller can also synchronize ARP entries among distributed VXLAN IP gateways. When you use a controller, do not enable dynamic ARP entry synchronization.

Examples

# Enable dynamic ARP entry synchronization for distributed VXLAN IP gateways.

<Sysname> system-view

[Sysname] arp distributed-gateway dynamic-entry synchronize

Related commands

distributed-gateway local

local-proxy-arp enable (Layer 3—IP Services Command Reference)

bandwidth

Use bandwidth to set the expected bandwidth for a VSI interface.

Use undo bandwidth to restore the default.

Syntax

bandwidth bandwidth-value

undo bandwidth

Default

The expected bandwidth (in kbps) equals the interface baudrate divided by 1000.

Views

VSI interface view

VSI subinterface view

Predefined user roles

network-admin

context-admin

Parameters

bandwidth-value: Specifies the expected bandwidth, in the range of 1 to 400000000 kbps.

Usage guidelines

The expected bandwidth is an informational parameter used only by higher-layer protocols for calculation. You cannot adjust the actual bandwidth of an interface by using this command.

Examples

# Set the expected bandwidth to 10000 kbps for VSI-interface 100.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] bandwidth 10000

default

Use default to restore the default settings for a VSI interface.

Syntax

default

Views

VSI interface view

VSI subinterface view

Predefined user roles

network-admin

context-admin

Usage guidelines

CAUTION:

The default command might interrupt ongoing network services. Make sure you are fully aware of the impact of this command when you use it on a live network.

This command might fail to restore the default settings for some commands for reasons such as command dependencies and system restrictions.

To resolve this problem:

1. Use the display this command in interface view to identify these commands.

2. Use their undo forms or follow the command reference to restore their default settings.

3. If the restoration attempt still fails, follow the error message instructions to resolve the problem.

Examples

# Restore the default settings for VSI-interface 100.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] default

This command will restore the default settings. Continue? [Y/N]:y

description

Use description to configure the description of a VSI interface.

Use undo description to restore the default.

Syntax

description text

undo description

Default

The description of a VSI interface is interface-name plus Interface (for example, Vsi-interface100 Interface).

Views

VSI interface view

VSI subinterface view

Predefined user roles

network-admin

context-admin

Parameters

text: Specifies a description, a case-sensitive string of 1 to 255 characters.

Examples

# Configure the description as gateway for VXLAN 10 for VSI-interface 100.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] description gateway for VXLAN 10

display interface vsi-interface

Use display interface vsi-interface to display information about VSI interfaces.

Syntax

display interface [ vsi-interface [ vsi-interface-id ] ] [ brief [ description | down ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

Parameters

vsi-interface [ vsi-interface-id ]: Specifies a VSI interface by its number. Make sure the specified VSI interface has been created on the device. If you do not specify the vsi-interface [ vsi-interface-id ] option, this command displays information about all interfaces. If you specify only the vsi-interface keyword, this command displays information about all VSI interfaces. If you specify a VSI interface, this command displays information about the specified interface.

brief: Display brief interface information. If you do not specify this keyword, the command displays detailed interface information.

description: Displays complete interface descriptions. If you do not specify this keyword, the command displays only the first 27 characters of interface descriptions.

down: Displays interfaces that are physically down as well as the down reason. If you do not specify this keyword, the command does not filter output by physical interface state.

Examples

# Display information about VSI-interface 100.

<Sysname> display interface vsi-interface 100

Vsi-interface100

Current state: UP

Line protocol state: UP

Description: Vsi-interface100 Interface

Bandwidth: 1000000 kbps

Maximum transmission unit: 1500

Internet address: 10.1.1.1/24 (primary)

IP packet frame type: Ethernet II, hardware address: 0011-2200-0102

IPv6 packet frame type: Ethernet II, hardware address: 0011-2200-0102

Physical: Unknown, baudrate: 1000000 kbps

Last clearing of counters: Never

Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Input: 0 packets, 0 bytes, 0 drops

Output: 0 packets, 0 bytes, 0 drops

Table 9 Command output

Field	Description
Current state	Physical link state of the interface: · Administratively DOWN—The interface has been shut down by using the shutdown command. · DOWN—The interface is administratively up, but its physical state is down. · UP—The interface is both administratively and physically up.
Line protocol state	Data link layer state of the interface: · UP—The data link layer protocol is up. · UP(spoofing)—The data link layer protocol is up, but the link is an on-demand link or does not exist. · DOWN—The data link layer protocol is down.
Description	Description of the interface.
Bandwidth	Expected bandwidth of the interface.
Maximum transmission unit	MTU of the interface.
Internet protocol processing: Disabled	The interface is not assigned an IP address and cannot process IP packets.
Internet address: ip-address/mask-length (Type)	IP address of the interface and type of the address in parentheses. Possible IP address types include: · Primary—Manually configured primary IP address. · Sub—Manually configured secondary IP address. If the interface has both primary and secondary IP addresses, the primary IP address is displayed. If the interface has only secondary IP addresses, the lowest secondary IP address is displayed. · DHCP-allocated—DHCP allocated IP address. For more information, see DHCP client configuration in Layer 3—IP Services Configuration Guide. · BOOTP-allocated—BOOTP allocated IP address. For more information, see BOOTP client configuration in Layer 3—IP Services Configuration Guide. · PPP-negotiated—IP address assigned by a PPP server during PPP negotiation. For more information, see PPP configuration in PPP and PPPoE Configuration Guide. · Unnumbered—IP address borrowed from another interface. · MAD—IP address assigned to an IRF member device for MAD on the interface. For more information, see IRF configuration in Virtual Technologies Configuration Guide.
IP packet frame type	IPv4 packet framing format.
hardware address	MAC address.
IPv6 packet frame type	IPv6 packet framing format.
Physical	Physical type of the interface, which is fixed at Unknown.
baudrate	Interface baudrate in kbps.
Last clearing of counters	Last time when the reset counters interface vsi-interface command was used to clear interface statistics. This field displays Never if the reset counters interface vsi-interface command has never been used on the interface since the device startup.
Last 300 seconds input rate	Average input rate for the last 300 seconds.
Last 300 seconds output rate	Average output rate for the last 300 seconds.
Input: 0 packets, 0 bytes, 0 drops	Incoming traffic statistics on the interface: · Number of incoming packets. · Number of incoming bytes. · Number of dropped incoming packets.
Output: 0 packets, 0 bytes, 0 drops	Outgoing traffic statistics on the interface: · Number of outgoing packets. · Number of outgoing bytes. · Number of dropped outgoing packets.

# Display brief information about all VSI interfaces.

<Sysname> display interface vsi-interface brief

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface Link Protocol Primary IP Description

Vsi100 DOWN DOWN --

# Display brief information and complete description for VSI-interface 100.

<Sysname> display interface vsi-interface 100 brief description

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface Link Protocol Primary IP Description

Vsi100 UP UP 1.1.1.1 VSI-interface100

# Displays interfaces that are physically down and the down reason.

<Sysname> display interface brief down

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Interface Link Cause

Vsi100 DOWN Administratively

Vsi200 DOWN Administratively

Table 10 Command output

Field	Description
Interface	Abbreviated interface name.
Link	Physical link state of the interface: · UP—The interface is physically up. · DOWN—The interface is physically down. · ADM—The interface has been shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command. · Stby—The interface is a backup interface in standby state. To see the primary interface, use the display interface-backup state command.
Protocol	Data link layer protocol state of the interface: · UP—The data link layer protocol of the interface is up. · UP (s)—The data link layer protocol of the interface is up, but the link is an on-demand link or does not exist. The (s) attribute represents the spoofing flag. · DOWN—The data link layer protocol of the interface is down.
Primary IP	Primary IP address of the interface. This field displays two hyphens (--) if the interface does not have an IP address.
Description	Description of the interface.
Cause	Cause for the physical link state of an interface to be DOWN: · Administratively—The interface has been manually shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command. · Not connected—The interface is not mapped to any VSI, or the mapped VSI does not have any AC or VXLAN tunnel.

Related commands

reset counters interface vsi-interface

distributed-gateway local

Use distributed-gateway local to specify a VSI interface as a distributed gateway to provide services for the local site.

Use undo distributed-gateway local to restore the default.

Syntax

distributed-gateway local

undo distributed-gateway local

Default

A VSI interface is not a distributed gateway.

Views

VSI interface view

Predefined user roles

network-admin

context-admin

Usage guidelines

If a VXLAN uses distributed gateway services, you must assign the same IP address to the VXLAN's VSI interfaces on different VTEPs. To avoid IP address conflicts, you must specify the VSI interface on each VTEP as a distributed gateway.

Examples

# Specify VSI-interface 100 as a distributed gateway.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] distributed-gateway local

gateway subnet

Use gateway subnet to assign a subnet to a VSI.

Use undo gateway subnet to remove a subnet from a VSI.

Syntax

gateway subnet { ipv4-address wildcard-mask | ipv6-address prefix-length }

undo gateway subnet { ipv4-address wildcard-mask | ipv6-address prefix-length }

Default

No subnet is assigned to a VSI.

Views

VSI view

Predefined user roles

network-admin

context-admin

Parameters

ipv4-address: Specifies an IPv4 subnet address in dotted-decimal notation.

wildcard-mask: Specifies a wildcard mask in dotted decimal notation. In contrast to a network mask, the 0 bits in a wildcard mask represent "do care" bits, and the 1 bits represent "don't care" bits. If the "do care" bits in a packet's IP address are identical to the "do care" bits in the specified subnet address, the packet is assigned to the VSI. All "don't care" bits are ignored. The 0s and 1s in a wildcard mask can be noncontiguous. For example, 0.255.0.255 is a valid wildcard mask.

ipv6-address prefix-length: Specifies an IPv6 subnet address and the address prefix length in the range of 1 to 128.

Usage guidelines

You must configure this command on VSIs that share a gateway interface. This command enables the VSI interface to identify the VSI of a packet.

You can assign a maximum of eight IPv4 and IPv6 subnets to a VSI.

You must specify a gateway interface for a VSI before you can assign subnets to the VSI. If you remove the gateway interface from the VSI, the VSI's subnet settings are automatically deleted.

For VSIs that share a gateway interface, the subnets must be unique.

Examples

# Assign subnet 100.0.10.0/24 to VSI vxlan.

<Sysname> system-view

[Sysname] vsi vxlan

[Sysname-vsi-vxlan] gateway subnet 100.0.10.0 0.0.0.255

gateway vsi-interface

Use gateway vsi-interface to specify a gateway interface for a VSI.

Use undo gateway vsi-interface to restore the default.

Syntax

gateway vsi-interface vsi-interface-id

undo gateway vsi-interface

Default

No gateway interface is specified for a VSI.

Views

VSI view

Predefined user roles

network-admin

context-admin

Parameters

vsi-interface-id: Specifies a VSI interface by its number. The value range for this argument is 0 to 8191.

Usage guidelines

A VSI can have only one gateway interface. Multiple VSIs can share a gateway interface.

Examples

# Specify VSI-interface 100 as the gateway interface for VSI vpna.

<Sysname> system-view

[Sysname] vsi vpna

[Sysname-vsi-vpna] gateway vsi-interface 100

Related commands

interface vsi-interface

Use interface vsi-interface to create a VSI interface and enter its view, or enter the view of an existing VSI interface.

Use undo interface vsi-interface to delete a VSI interface.

Syntax

interface vsi-interface vsi-interface-id

undo interface vsi-interface vsi-interface-id

Default

No VSI interfaces exist.

Views

System view

Predefined user roles

network-admin

context-admin

Parameters

vsi-interface-id: Specifies a VSI interface number. The value range for this argument is 0 to 8191.

Examples

# Create VSI-interface 100 and enter VSI interface view.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100]

Related commands

gateway vsi-interface

mac-address

Use mac-address to assign a MAC address to a VSI interface.

Use undo mac-address to restore the default.

Syntax

mac-address mac-address

undo mac-address

Default

The MAC address of a VSI interface is the bridge MAC address.

Views

VSI interface view

Predefined user roles

network-admin

context-admin

Parameters

mac-address: Specifies a MAC address in H-H-H format.

Examples

# Assign MAC address 0001-0001-0001 to VSI-interface 100.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] mac-address 1-1-1

mtu

Use mtu to set the MTU for a VSI interface.

Use undo mtu to restore the default.

Syntax

mtu size

undo mtu

Default

The MTU is 1500 bytes.

Views

VSI interface view

VSI subinterface view

Predefined user roles

network-admin

context-admin

Parameters

size: Specifies an MTU value in the range of 46 to 1500 bytes.

Examples

# Set the MTU to 1430 bytes for VSI-interface 100.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] mtu 1430

reset counters interface vsi-interface

Use reset counters interface vsi-interface to clear packet statistics on VSI interfaces.

Syntax

reset counters interface [ vsi-interface [ vsi-interface-id ] ]

Views

User view

Predefined user roles

network-admin

context-admin

Parameters

vsi-interface [ vsi-interface-id ]: Specifies a VSI interface by its number. Make sure the specified VSI interface has been created on the device. If you do not specify the vsi-interface [ vsi-interface-id ] option, this command clears packet statistics on all interfaces. If you specify only the vsi-interface keyword, this command clears packet statistics on all VSI interfaces. If you specify a VSI interface, this command clears packet statistics on the specified interface.

Usage guidelines

Use this command to clear history statistics before you collect traffic statistics for a time period.

Examples

# Clear packet statistics on VSI-interface 100.

<Sysname> reset counters interface vsi-interface 100

Related commands

display interface vsi-interface

shutdown

Use shutdown to shut down a VSI interface.

Use undo shutdown to bring up a VSI interface.

Syntax

shutdown

undo shutdown

Default

A VSI interface is not manually shut down.

Views

VSI interface view

Predefined user roles

network-admin

context-admin

Usage guidelines

CAUTION:

If you shut down a VSI interface, the VXLAN network using this VSI interface as the gateway will be unable to communicate with other networks at Layer 3. Make sure you are fully aware of the impact of this command when you use it on a live network.

Examples

# Shut down VSI-interface 100.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] shutdown

vtep group member local

Use vtep group member local to assign the local VTEP to a VTEP group.

Use undo vtep group member local to remove the local VTEP from a VTEP group.

Syntax

vtep group group-ip member local member-ip

undo vtep group group-ip member local

Default

A VTEP is not assigned to any VTEP group.

Views

System view

Predefined user roles

network-admin

context-admin

Parameters

group-ip: Specifies a VTEP group by its group IP address. The IP address must already exist on the local VTEP.

member-ip: Specifies the member VTEP IP address for the local VTEP. The IP address must already exist on the local VTEP.

Usage guidelines

Member VTEPs in a VTEP group cannot use the group IP address or share an IP address.

Examples

# Assign the local VTEP to VTEP group 1.1.1.1, and specify 2.2.2.2 as the member VTEP IP address of the local VTEP.

<Sysname> system-view

[Sysname] vtep group 1.1.1.1 member local 2.2.2.2

Related commands

vtep group member remote

Use vtep group member remote to specify a VTEP group and its member VTEPs.

Use undo vtep group member remote to remove a VTEP group and its member VTEPs.

Syntax

vtep group group-ip member remote member-ip&<1-8>

undo vtep group group-ip member remote

Default

No VTEP group is specified.

Views

System view

Predefined user roles

network-admin

context-admin

Parameters

group-ip: Specifies a VTEP group by its group IP address.

member-ip&<1-8>: Specifies a space-separated list of up to eight member VTEP IP addresses.

Examples

# Specify VTEP group 1.1.1.1 and its member VTEPs at 2.2.2.2, 3.3.3.3, and 4.4.4.4.

<Sysname> system-view

[Sysname] vtep group 1.1.1.1 member remote 2.2.2.2 3.3.3.3 4.4.4.4

Related commands

vtep group member local

vxlan tunnel arp-learning disable

Use vxlan tunnel arp-learning disable to disable remote ARP learning for VXLANs.

Use undo vxlan tunnel arp-learning disable to enable remote ARP learning for VXLANs.

Syntax

vxlan tunnel arp-learning disable

undo vxlan tunnel arp-learning disable

Default

Remote ARP learning is enabled for VXLANs.

Views

System view

Predefined user roles

network-admin

context-admin

Usage guidelines

By default, the device learns ARP information of remote VMs from packets received on VXLAN tunnel interfaces. To save resources on VTEPs in an SDN transport network, you can temporarily disable remote ARP learning when the controller and VTEPs are synchronizing entries. After the entry synchronization is completed, use the undo vxlan tunnel arp-learning disable command to enable remote ARP learning.

As a best practice, disable remote ARP learning for VXLANs only when the controller and VTEPs are synchronizing entries.

Examples

# Disable remote ARP learning for VXLANs.

<Sysname> system

[Sysname] vxlan tunnel arp-learning disable

20-VXLAN Command Reference

VXLAN commands

display l2vpn interface

l2vpn enable

mtu

statistics enable (tunnel interface view)

vxlan

vxlan udp-port

display interface vsi-interface

reset counters interface vsi-interface

Cloud & AI

InterConnect

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Resources

Partner Business Management

Company Information

News & Events

Contact Us