01-Fundamentals Configuration Guide

HomeSupportConfigure & DeployConfiguration GuidesH3C S6800[S6860][S6861] (R27xx) & S6820 (R630x) Switch Series Configuration Guide-6W10201-Fundamentals Configuration Guide
04-FTP and TFTP configuration
Title Size Download
04-FTP and TFTP configuration 154.92 KB

Configuring FTP

About FTP

File Transfer Protocol (FTP) is an application layer protocol for transferring files from one host to another over an IP network. It uses TCP port 20 to transfer data and TCP port 21 to transfer control commands.

FTP is based on the client/server model. The device can act as the FTP server or FTP client.

FTP file transfer modes

FTP supports the following transfer modes:

·           Binary mode—Used to non-text files, such as .app, .bin, and .btm files.

·           ASCII mode—Used to transfer text files, such as .txt, .bat, and .cfg files.

When the device acts as the FTP client, you can set the transfer mode (binary by default). When the device acts as the FTP server, the transfer mode is determined by the FTP client.

FTP operation modes

FTP can operate in either of the following modes:

·           Active mode (PORT)—The FTP server initiates the TCP connection. This mode is not suitable when the FTP client is behind a firewall, for example, when the FTP client resides in a private network.

·           Passive mode (PASV)—The FTP client initiates the TCP connection. This mode is not suitable when the server does not allow the client to use a random unprivileged port greater than 1024.

FTP operation mode varies depending on the FTP client program.

FIPS compliance

The device supports the FIPS mode that complies with NIST FIPS 140-2 requirements. Support for features, commands, and parameters might differ in FIPS mode and non-FIPS mode. For more information about FIPS mode, see Security Configuration Guide.

FTP is not supported in FIPS mode.

Using the device as an FTP server

To use the device as an FTP server, you must enable the FTP server and configure authentication and authorization on the device. Other commands are optional.

FTP server configuration tasks at a glance

To use the device as an FTP server, perform the following tasks:

1.      Enabling the FTP server

2.      Configuring client authentication and authorization

3.      (Optional.) Configuring FTP server access control

4.      (Optional.) Setting connection management parameters

5.      (Optional.) Specifying an SSL server policy for SFTP connections

6.      (Optional.) Setting the DSCP value for outgoing FTP packets

7.      (Optional.) Manually releasing FTP connections

Enabling the FTP server

1.      Enter system view.

system-view

2.      Enable the FTP server.

ftp server enable

By default, the FTP server is disabled.

Configuring client authentication and authorization

Perform this task on the FTP server to authenticate FTP clients and set the authorized directories that authenticated clients can access.

The following authentication modes are available:

·           Local authentication—The device looks up the client's username and password in the local user account database. If a match is found, authentication succeeds.

·           Remote authentication—The device sends the client's username and password to a remote authentication server for authentication. The user account is configured on the remote authentication server rather than the device.

The following authorization modes are available:

·           Local authorization—The device assigns authorized directories to FTP clients based on the locally configured authorization attributes.

·           Remote authorization—A remote authorization server assigns authorized directories on the device to FTP clients.

For more information about configuring authentication and authorization, see AAA in Security Configuration Guide.

Configuring FTP server access control

About FTP server access control

Use ACLs to prevent unauthorized access. If an applied ACL does not exist or does not have any rules, no user login restriction is applied. If the ACL exists and has rules, only FTP clients permitted by the ACL can access the device.

Restrictions and guidelines

This configuration takes effect only for FTP connections to be established. It does not affect existing FTP connections.

If you configure FTP server access control multiple times, the most recent configuration takes effect.

Procedure

1.      Enter system view.

system-view

2.      Use an ACL to control access to the FTP server.

ftp server acl { advanced-acl-number | basic-acl-number | ipv6 { advanced-acl-number | basic-acl-number } }

By default, no ACL is used for access control.

3.      Enable logging for FTP login attempts that are denied by the FTP login control ACL.

ftp server acl-deny-log enable

By default, logging is disabled for FTP login attempts that are denied by the FTP login control ACL.

Setting connection management parameters

1.      Enter system view.

system-view

2.      Set the FTP connection idle-timeout timer.

ftp timeout minutes

By default, the FTP connection idle-timeout timer is 30 minutes.

If no data transfer occurs on an FTP connection before the idle-timeout timer expires, the FTP server closes the FTP connection.

3.      Set the maximum number of concurrent FTP users.

aaa session-limit ftp max-sessions

By default, the maximum number of concurrent FTP users is 32.

Changing this setting does not affect users who are currently online. If the new limit is less than the number of online FTP users, no additional FTP users can log in until the number drops below the new limit. For more information about this command, see Security Command Reference.

Specifying an SSL server policy for SFTP connections

About specifying an SSL server policy for SFTP connections

After you associate an SSL server policy with the device, a client that supports SFTP will establish a secure connection to the device to ensure data security.

Procedure

1.      Enter system view.

system-view

2.      Associate an SSL server policy with the FTP server to ensure data security.

ftp server ssl-server-policy policy-name

By default, no SSL server policy is associated with the FTP server.

Setting the DSCP value for outgoing FTP packets

1.      Enter system view.

system-view

2.      Set the DSCP value for outgoing FTP packets.

IPv4:

ftp server dscp dscp-value

IPv6:

ftp server ipv6 dscp dscp-value

By default, the DSCP value is 0.

Manually releasing FTP connections

To manually release FTP connections, execute the following commands in user view:

·           Release the FTP connection established by using a specific user account:

free ftp user username

·           Release the FTP connection to a specific IP address:

free ftp user-ip [ ipv6 ] ip-address [ port port ]

Display and maintenance commands for the FTP server

Execute display commands in any view.

 

Task

Command

Display FTP server configuration and status information.

display ftp-server

Display detailed information about online FTP users.

display ftp-user

Example: Using the device as an FTP server

Network configuration

·           Configure the IRF fabric as an FTP server.

·           Create a local user account named abc on the FTP server. Set the password to 123456.

·           Use the user account to log in to the FTP server from the FTP client.

·           Upload the temp.bin file from the FTP client to the FTP server.

Download configuration file config.cfg from the FTP server to the FTP client for backup.

Figure 1 Network diagram

Procedure

1.      Configure IP addresses as shown in Figure 1. Make sure the IRF fabric and the PC can reach each other. (Details not shown.)

2.      Configure the FTP server:

# Examine the storage space on the member devices. If the free space is insufficient, use the delete/unreserved file command to delete unused files. (Details not shown.)

# Create a local user with username abc and password 123456.

<Sysname> system-view

[Sysname] local-user abc class manage

[Sysname-luser-manage-abc] password simple 123456

# Assign the network-admin user role to the user. Set the working directory to the root directory of the flash memory on the master. (To set the working directory to the root directory of the flash memory on the subordinate member, you must include the slot number in the directory path.)

[Sysname-luser-manage-abc] authorization-attribute user-role network-admin work-directory flash:/

# Assign the service type FTP to the user.

[Sysname-luser-manage-abc] service-type ftp

[Sysname-luser-manage-abc] quit

# Enable the FTP server.

[Sysname] ftp server enable

[Sysname] quit

3.      Perform FTP operations from the FTP client:

# Log in to the FTP server at 1.1.1.1 using username abc and password 123456.

c:\> ftp 1.1.1.1

Connected to 1.1.1.1.

220 FTP service ready.

User(1.1.1.1:(none)):abc

331 Password required for abc.

Password:

230 User logged in.

# Use the ASCII mode to download configuration file config.cfg from the FTP server to the PC for backup.

ftp> ascii

200 TYPE is now ASCII

ftp> get config.cfg back-config.cfg

# Use the binary mode to upload the temp.bin file from the PC to the root directory of the flash memory on the master.

ftp> binary

200 TYPE is now 8-bit binary

ftp> put temp.bin

# Exit FTP.

ftp> bye

Using the device as an FTP client

FTP client configuration tasks at a glance

To use the device as an FTP server, perform the following tasks:

1.      Establishing an FTP connection

2.      (Optional.) Displaying command help information

3.      (Optional.) Displaying directories and files on the FTP server

4.      (Optional.) Managing directories on the FTP server

5.      (Optional.) Working with files on the FTP server

6.      (Optional.) Changing to another user account

7.      (Optional.) Maintaining and troubleshooting the FTP connection

8.      (Optional.) Terminating the FTP connection

Establishing an FTP connection

FTP connection establishment task list

To establish an FTP connection, perform the following tasks:

1.      (Optional.) Specifying a source IP address for outgoing FTP packets

2.      Establishing an FTP connection

3.      Setting the FTP file transfer mode and operation mode

Restrictions and guidelines

The source IP address specified in the ftp command takes precedence over the one set by the ftp client source command.

The source IP address specified in the ftp ipv6 command takes precedence over the one set by the ftp client ipv6 source command.

Specifying a source IP address for outgoing FTP packets

1.      Enter system view.

system-view

2.      Specify a source IP address for outgoing FTP packets.

IPv4:

ftp client source { interface interface-type interface-number | ip source-ip-address }

By default, no source IP address is specified. The device uses the primary IP address of the output interface as the source IP address.

IPv6:

ftp client ipv6 source { interface interface-type interface-number | ipv6 source-ipv6-address }

By default, no source IPv6 address is specified. The source address is automatically selected as defined in RFC 3484.

Establishing an FTP connection

·           Log in to the FTP server from user view.

IPv4:

ftp [ ftp-server [ service-port ] [ vpn-instance vpn-instance-name ] [ dscp dscp-value | source { interface interface-type interface-number | ip source-ip-address } | -d ] * ]

IPv6:

ftp ipv6 [ ftp-server [ service-port ] [ vpn-instance vpn-instance-name ] [ dscp dscp-value | source { interface interface-type interface-number | ipv6 source-ipv6-address } | -d ] * [ -i interface-type interface-number ] ]

·           Log in to the FTP server from FTP client view.

a.    Enter FTP client view.

ftp [ ipv6 ]

b.    Log in to the FTP server.

open server-address [ service-port ]

Setting the FTP file transfer mode and operation mode

1.      Enter FTP client view from user view.

ftp

2.      Set the file transfer mode.

¡  Set the file transfer mode to ASCII.

ascii

¡  Set the file transfer mode to binary.

binary

The default file transfer mode is binary.

3.      Change the FTP operation mode.

passive

The default FTP operation mode is passive.

Displaying command help information

1.      Enter FTP client view from user view.

ftp

2.      Display command help information.

¡  help [ command-name ]

¡  ? [ command-name ]

Displaying directories and files on the FTP server

1.      Enter FTP client view from user view.

ftp

2.      Display directories and files on the FTP server.

¡  dir [ remotefile [ localfile ] ]

¡  ls [ remotefile [ localfile ] ]

Managing directories on the FTP server

Prerequisites

Use the dir or ls command to display the directories and files on the FTP server.

Procedure

1.      Enter FTP client view from user view.

ftp

2.      Manage directories on the FTP server.

¡  Display the working directory that is being accessed on the FTP server.

pwd

¡  Change the working directory on the FTP server.

cd { directory | .. | / }

¡  Return to the upper level directory on the FTP server.

cdup

¡  Create a directory on the FTP server.

mkdir directory

¡  Delete a directory from the remote FTP server.

rmdir directory

Managing directories on the FTP client

1.      Enter FTP client view from user view.

ftp

2.      Display or change the local working directory of the FTP client.

lcd [ directory | / ]

To upload a file, use this command to change to the directory where the file resides. Downloaded files are saved in the working directory.

Working with files on the FTP server

Prerequisites

Use the dir or ls command to display the directories and files on the FTP server.

Procedure

1.      Enter FTP client view from user view.

ftp

2.      Work with files on the FTP server.

¡  Delete a file from the FTP server permanently.

delete remotefile

This command requires that you have the delete right.

¡  Rename a file.

rename [ oldfilename [ newfilename ] ]

¡  Upload a file to the FTP server.

put localfile [ remotefile ]

¡  Download a file from the FTP server.

get remotefile [ localfile ]

¡  Add the content of a file on the FTP client to a file on the FTP server.

append localfile [ remotefile ]

¡  Specify the retransmit marker.

restart marker

Use this command together with the put, get, or append command.

¡  Update a local file.

newer remotefile

¡  Get the missing part of a file.

reget remotefile [ localfile ]

Changing to another user account

About changing to another user account

After you log in to the FTP server, you can initiate an FTP authentication to change to a new account. By changing to a new account, you can get a different privilege without re-establishing the FTP connection.

Restrictions and guidelines

For successful account change, you must enter the new username and password correctly. A wrong username or password can cause the FTP connection to be disconnected.

Procedure

1.      Enter FTP client view from user view.

ftp

2.      Initiate an FTP authentication on the current FTP connection.

user username [ password ]

Maintaining and troubleshooting the FTP connection

About maintaining and troubleshooting the FTP connection

After you use the device to establish an FTP connection to the FTP server, use the commands in this section to locate and troubleshoot problems about the FTP connection.

Procedure

1.      Enter FTP client view from user view.

ftp

2.      Maintain and troubleshoot the FTP connection.

¡  Display FTP commands supported by the FTP server.

rhelp

¡  Display help information about an FTP command that is supported by the FTP server.

rhelp protocol-command

¡  Display FTP server status.

rstatus

¡  Display detailed information about a directory or file on the FTP server.

rstatus remotefile

¡  Display FTP connection status.

status

¡  Display the system information of the FTP server.

system

¡  Enable or disable FTP operation information display.

verbose

By default, this function is enabled.

¡  Enable FTP client debugging.

debug

By default, FTP client debugging is disabled.

¡  Clear the reply information in the buffer.

reset

Terminating the FTP connection

1.      Enter FTP client view from user view.

ftp

2.      Terminate the connection.

¡  Terminate the connection to the FTP server without exiting FTP client view.

disconnect

close

¡  Terminate the connection to the FTP server and return to user view.

bye

quit

Display and maintenance commands for the FTP client

Execute the display command in any view.

 

Task

Command

Display source IP address information on the FTP client.

display ftp client source

Example: Using the device as an FTP client

Network configuration

As shown in Figure 2, the PC is acting as an FTP server. A user account with username abc and password 123456 has been created on the PC.

·           Use the IRF fabric as an FTP client to log in to the FTP server.

·           Download the temp.bin file from the FTP server to the FTP client.

Upload configuration file config.cfg from the FTP client to the FTP server for backup.

Figure 2 Network diagram

Procedure

# Configure IP addresses as shown in Figure 2. Make sure the IRF fabric and PC can reach each other. (Details not shown.)

# Examine the storage space on the member devices. If the free space is insufficient, use the delete/unreserved file command to delete unused files. (Details not shown.)

# Log in to the FTP server at 10.1.1.1 using username abc and password 123456.

<Sysname> ftp 10.1.1.1

Press CTRL+C to abort.

Connected to 10.1.1.1 (10.1.1.1).

220 WFTPD 2.0 service (by Texas Imperial Software) ready for new user

User (10.1.1.1:(none)): abc

331 Give me your password, please

Password:

230 Logged in successfully

Remote system type is MSDOS.

ftp>

# Set the file transfer mode to binary.

ftp> binary

200 TYPE is now 8-bit binary

# Download the temp.bin file from the PC to the root directory of the flash memory on the master device.

ftp> get temp.bin

local: temp.bin remote: temp.bin

150 Connecting to port 47457

226 File successfully transferred

23951480 bytes received in 95.399 seconds (251.0 kbyte/s)

# Download the temp.bin file from the PC to the root directory of the flash memory on the subordinate member (with member ID of 2).

ftp> get temp.bin slot2#flash:/temp.bin

# Use the ASCII mode to upload configuration file config.cfg from the IRF fabric to the PC for backup.

ftp> ascii

200 TYPE is now ASCII

ftp> put config.cfg back-config.cfg

local: config.cfg remote: back-config.cfg

150 Connecting to port 47461

226 File successfully transferred

3494 bytes sent in 5.646 seconds (618.00 kbyte/s)

ftp> bye

221-Goodbye. You uploaded 2 and downloaded 2 kbytes.

221 Logout.

<Sysname>


Configuring TFTP

About TFTP

Trivial File Transfer Protocol (TFTP) is a simplified version of FTP for file transfer over secure reliable networks. TFTP uses UDP port 69 for data transmission. In contrast to TCP-based FTP, TFTP does not require authentication or complex message exchanges, and is easier to deploy. TFTP is suited for reliable network environments.

FIPS compliance

The device supports the FIPS mode that complies with NIST FIPS 140-2 requirements. Support for features, commands, and parameters might differ in FIPS mode and non-FIPS mode. For more information about FIPS mode, see Security Configuration Guide.

TFTP is not supported in FIPS mode.

Restrictions and guidelines: TFTP configuration

You can upload a file from the device to the TFTP server or download a file from the TFTP server to the device.

As a best practice to download a file, specify a nonexistent file name as the destination file name. If you download a file with a file name that exists in the target directory, the device deletes the existing file and saves the new one. If file download fails due to network disconnection or other reasons, the original file cannot be restored.

The device can act only as a TFTP client.

Configuring and using the IPv4 TFTP client

1.      Enter system view.

system-view

2.      (Optional.) Use an ACL to control the client's access to TFTP servers.

tftp-server acl acl-number

By default, no ACL is used for access control.

3.      Specify the source IP address for TFTP packets sent by the TFTP client.

tftp client source { interface interface-type interface-number | ip source-ip-address }

By default, no source IP address is specified. The device uses the primary IP address of the output interface as the source IP address.

4.      Return to user view.

quit

5.      Download or upload a file in an IPv4 network.

tftp tftp-server { get | put | sget } source-filename [ destination-filename ] [ vpn-instance vpn-instance-name ] [ dscp dscp-value | source { interface interface-type interface-number | ip source-ip-address } ] *

The source IP address specified in this command takes precedence over the source IP address set by using the tftp client source command.

Configuring and using the IPv6 TFTP client

1.      Enter system view.

system-view

2.      (Optional.) Use an ACL to control the client's access to TFTP servers.

tftp-server ipv6 acl ipv6-acl-number

By default, no ACL is used for access control.

3.      Specify the source IPv6 address for TFTP packets sent by the TFTP client.

tftp client ipv6 source { interface interface-type interface-number | ipv6 source-ipv6-address }

By default, no source IPv6 address is specified. The source address is automatically selected as defined in RFC 3484.

4.      Return to user view.

quit

5.      Download or upload a file in an IPv6 network.

tftp ipv6 tftp-server [ -i interface-type interface-number ] { get | put | sget } source-filename [ destination-filename ] [ vpn-instance vpn-instance-name ] [ dscp dscp-value | source { interface interface-type interface-number | ipv6 source-ipv6-address } ] *

The source IP address specified in this command takes precedence over the one set by the tftp client ipv6 source command.

  • Cloud & AI
  • InterConnect
  • Intelligent Computing
  • Security
  • SMB Products
  • Intelligent Terminal Products
  • Product Support Services
  • Technical Service Solutions
All Services
  • Resource Center
  • Policy
  • Online Help
All Support
  • Become a Partner
  • Partner Resources
  • Partner Business Management
All Partners
  • Profile
  • News & Events
  • Online Exhibition Center
  • Contact Us
All About Us
新华三官网