- Table of Contents
-
- 03-WLAN Command References
- 00-Preface
- 01-AP management commands
- 02-Radio management commands
- 03-WLAN access commands
- 04-WLAN security commands
- 05-WLAN authentication commands
- 06-WIPS commands
- 07-WLAN QoS commands
- 08-WLAN roaming commands
- 09-WLAN load balancing commands
- 10-WLAN radio resource measurement commands
- 11-Channel scanning commands
- 12-Band navigation commands
- 13-WLAN high availability commands
- 14-802.11r commands
- 15-Wireless location commands
- 16-AC hierarchy commands
- 17-WLAN RRM commands
- 18-WLAN IP snooping commands
- 19-WLAN probe commands
- 20-WLAN forwarding commands
- 21-Spectrum management commands
- 22-WLAN radio load balancing commands
- 23-User isolation commands
- 24-Packet capture commands
- 25-802.1X client commands
- 26-IP source guard commands
- Related Documents
-
Title | Size | Download |
---|---|---|
14-802.11r commands | 33.12 KB |
WLAN 802.11r commands
ft enable
Use ft enable to enable fast BSS transition (FT).
Use undo ft enable to disable FT.
Syntax
ft enable
undo ft enable
Default
FT is disabled.
Views
Service template view
Predefined user roles
network-admin
Usage guidelines
FT minimizes the delay when a client roams from a BSS to another BSS within the same ESS. During 802.11r FT, a client needs to exchange messages with the target AP. FT provides two message exchanging methods.
Enable FT only when the service template is disabled.
If FT is enabled, you must disable WPA IE and local authentication. To disable WPA IE, use the undo security-ie wpa command.
Examples
# Enable FT.
<Sysname> system-view
[Sysname] wlan service-template st
[Sysname-wlan-st-st] ft enable
Related commands
security-ie
ft method
Use ft method to set the FT method.
Use undo ft method to restore the default.
Syntax
ft method { over-the-air | over-the-ds }
undo ft method
Default
The FT method is over-the-air.
Views
Service template view
Predefined user roles
network-admin
Parameters
over-the-air: Specifies over-the-air FT. This method enables clients to communicate directly with the target AP for pre-roaming authentication.
over-the-ds: Specifies over-the-DS FT. This method enables clients to communicate with the target AP through the current AP for pre-roaming authentication.
Usage guidelines
Set the FT method only when the service template is disabled.
This command takes effect only when FT is enabled.
Examples
# Set the FT method to over-the-DS.
<Sysname> system-view
[Sysname] wlan service-template st
[Sysname-wlan-st-st] ft method over-the-ds
Related commands
ft enable
ft reassociation-timeout
Use ft reassociation-timeout to set the reassociation timeout timer.
Use undo ft reassociation-timeout to restore the default.
Syntax
ft reassociation-timeout timeout
undo ft reassociation-timeout
Default
The reassociation timeout timer is 20 seconds.
Views
Service template view
Predefined user roles
network-admin
Parameters
timeout: Specifies the reassociation timeout timer in the range of 1 to 100 seconds.
Usage guidelines
The roaming process is terminated if a client does not send any reassociation requests before the timeout timer expires.
Set the reassociation timeout timer only when the service template is disabled.
This command takes effect only when FT is enabled.
Examples
# Set the reassociation timeout timer to 30 seconds.
<Sysname> system-view
[Sysname] wlan service-template st
[Sysname-wlan-st-st] ft reassociation-timeout 30
Related commands
ft enable