If you do not specify the sessions keyword or the statistics keyword, this command displays all information about 802.1X, including session information, statistics, and configurations.

If you do not specify the interface interface-type interface-number option, this command displays all global and port-specific 802.1X information.

Examples

# Display all information about 802.1X.

<Sysname> display dot1x

Global 802.1X parameters:

802.1X authentication : Enabled

CHAP authentication : Enabled

Max-tx period : 30 s

Handshake period : 15 s

Quiet timer : Disabled

Quiet period : 60 s

Supp timeout : 30 s

Server timeout : 100 s

Reauth period : 3600 s

Max auth requests : 2

SmartOn switch ID : 30

SmartOn supp timeout : 30 s

SmartOn retry counts : 3

EAD assistant function : Disabled

URL : http://www.dwsoft.com

Free IP : 6.6.6.0 255.255.255.0

EAD timeout : 30 min

Domain delimiter : @

Online 802.1X wired users : 1

Ten-GigabitEthernet1/1/1 is link-up

802.1X authentication : Enabled

Handshake : Enabled

Handshake reply : Disabled

Handshake security : Disabled

Unicast trigger : Disabled

Periodic reauth : Disabled

Port role : Authenticator

Authorization mode : Auto

Port access control : Port-based

Multicast trigger : Enabled

Mandatory auth domain : Not configured

Guest VLAN : 3

Auth-Fail VLAN : Not configured

Critical VLAN : Not configured

Critical voice VLAN : Disabled

Re-auth server-unreachable : Logoff

Max online users : 256

SmartOn : Disabled

Add Guest VLAN delay : EAPOL

User IP freezing : Disabled

Reauth period : 60 s

Send Packets Without Tag : Disabled

Max Attempts Fail Number : 0

EAPOL packets: Tx 3, Rx 3

Sent EAP Request/Identity packets : 1

EAP Request/Challenge packets: 1

EAP Success packets: 1

EAP Failure packets: 0

Received EAPOL Start packets : 1

EAPOL LogOff packets: 1

EAP Response/Identity packets : 1

EAP Response/Challenge packets: 1

Error packets: 0

Online 802.1X users: 1

MAC address Auth state

0001-0000-0000 Authenticated

Table 1 Command output

Field	Description
Global 802.1X parameters	Global 802.1X configuration.
802.1X authentication	Whether 802.1X is enabled globally.
CHAP authentication	Performs EAP termination and uses CHAP to communicate with the RADIUS server.
EAP authentication	Relays EAP packets and supports any of the EAP authentication methods to communicate with the RADIUS server.
PAP authentication	Performs EAP termination and uses PAP to communicate with the RADIUS server.
Max-tx period	Username request timeout timer in seconds.
Handshake period	Handshake timer in seconds.
Quiet timer	Status of the quiet timer, enabled or disabled.
Quiet period	Quiet timer in seconds.
Supp timeout	Client timeout timer in seconds.
Server timeout	Server timeout timer in seconds.
Reauth period	Periodic reauthentication timer in seconds.
Max auth requests	Maximum number of attempts for sending an authentication request to a client.
SmartOn switch ID	Switch ID for SmartOn authentication.
SmartOn supp timeout	SmartOn client timeout timer in seconds.
SmartOn retry counts	Maximum number of attempts for retransmitting an EAP-Request/Notification packet to a client.
EAD assistant function	Whether EAD assistant is enabled.
URL	Redirect URL for unauthenticated users using a Web browser to access the network.
Free IP	Network segment accessible to unauthenticated users.
EAD timeout	EAD rule timer in minutes.
Domain delimiter	Domain delimiters supported by the device.
Online 802.1X wired users	Number of wired online 802.1X users.
Ten-GigabitEthernet1/1/1 is link-up	Status of the port. In this example, Ten-GigabitEthernet 1/1/1 is up.
802.1X authentication	Whether 802.1X is enabled on the port.
Handshake	Whether the online user handshake feature is enabled on the port.
Handshake reply	Whether the online user handshake reply feature is enabled on the port.
Handshake security	Whether the online user handshake security feature is enabled on the port.
Unicast trigger	Whether the 802.1X unicast trigger is enabled on the port.
Periodic reauth	Whether 802.1X periodic reauthentication is enabled on the port.
Port role	Role of the port. The port functions only as an Authenticator.
Authorization mode	Authorization state of the port, which can be Force-Authorized, Auto, or Force-Unauthorized.
Port access control	Access control method of the port: · MAC-based—MAC-based access control. · Port-based—Port-based access control.
Multicast trigger	Whether the 802.1X multicast trigger feature is enabled.
Mandatory auth domain	Mandatory authentication domain on the port.
Guest VLAN	802.1X guest VLAN configured on the port. If no 802.1X guest VLAN is configured on the port, this field displays Not configured.
Auth-Fail VLAN	802.1X Auth-Fail VLAN configured on the port. If no 802.1X Auth-Fail VLAN is configured on the port, this field displays Not configured.
Critical VLAN	802.1X critical VLAN configured on the port. If no 802.1X critical VLAN is configured on the port, this field displays Not configured.
Critical voice VLAN	Whether the 802.1X critical voice VLAN is enabled on the port.
Re-auth server-unreachable	Whether to log off online 802.1X users or keep them online when no server is reachable for 802.1X reauthentication.
Max online users	Maximum number of concurrent 802.1X users on the port.
SmartOn	Whether SmartOn authentication is enabled on the port.
Add Guest VLAN delay	Status and mode of the 802.1X guest VLAN assignment delay feature on a port: · EAPOL—EAPOL-triggered 802.1X guest VLAN assignment delay is enabled. · NewMac—New MAC-triggered 802.1X guest VLAN assignment delay is enabled. · ALL—Both EAPOL-triggered and new MAC-triggered 802.1X guest VLAN assignment delays are enabled. · Disabled—802.1X guest VLAN assignment delay is disabled.
User IP freezing	Whether user IP freezing is enabled on the port.
Reauth period	Periodic reauthentication timer in seconds on the port.
Send Packets Without Tag	Whether the device sends 802.1X protocol packets out of the port without VLAN tags.
Max Attempts Fail Number	Maximum number of 802.1X authentication attempts for MAC authenticated users.
EAPOL packets	Number of sent (Tx) and received (Rx) EAPOL packets.
Sent EAP Request/Identity packets	Number of sent EAP-Request/Identity packets.
EAP Request/Challenge packets	Number of sent EAP-Request/MD5-Challenge packets.
EAP Success packets	Number of sent EAP-Success packets.
EAP Failure packets	Number of sent EAP-Failure packets.
Received EAPOL Start packets	Number of received EAPOL-Start packets.
EAPOL LogOff packets	Number of received EAPOL-LogOff packets.
EAP Response/Identity packets	Number of received EAP-Response/Identity packets.
EAP Response/Challenge packets	Number of received EAP-Response/MD5-Challenge packets.
Error packets	Number of received error packets.
Online 802.1X users	Number of online 802.1X users on the port.
MAC address	MAC addresses of the online 802.1X users.
Auth state	Authentication status of the online 802.1X users.

display dot1x connection

Use display dot1x connection to display information about online 802.1X users.

Syntax

display dot1x connection [ interface interface-type interface-number | slot slot-number | user-mac mac-address | user-name name-string ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface interface-type interface-number: Specifies a port by its type and number. If you do not specify a port, this command displays online 802.1X user information for all ports.

slot slot-number: Specifies an IRF member device by its member ID or specifies a PEX by its virtual slot number. On an IRF fabric, this command displays online 802.1X user information for all member devices if you do not specify a member device. On an IRF 3 system, this command displays online 802.1X user information for all IRF member devices and PEXs if you do not specify an IRF member device or PEX.

user-mac mac-address: Specifies an 802.1X user by MAC address. The mac-address argument represents the MAC address of the user, in the form of H-H-H. If you do not specify an 802.1X user, this command displays all online 802.1X user information.

user-name name-string: Specifies an 802.1X user by its name. The name-string argument represents the username, a case-sensitive string of 1 to 253 characters. If you do not specify an 802.1X user, this command displays all online 802.1X user information.

Examples

# Display information about all online 802.1X users.

<Sysname> display dot1x connection

Slot ID: 1

User MAC address: 0015-e9a6-7cfe

Access interface: Ten-GigabitEthernet1/1/1

Username: ias

Authentication domain: h3c

IPv4 address: 192.168.1.1

IPv6 address: 2000:0:0:0:1:2345:6789:abcd

Authentication method: CHAP

Initial VLAN: 1

Authorization untagged VLAN: 6

Authorization tagged VLAN list: 1 to 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 29 31 33

35 37 40 to 100

Authorization ACL ID: 3001

Termination action: Default

Session timeout period: 2 s

Online from: 2013/03/02 13:14:15

Online duration: 0h 2m 15s

Total 1 connections matched.

Table 2 Command output

Field	Description
User MAC address	MAC address of the user.
Access interface	Interface through which the user access the device.
Authentication domain	ISP domain used for 802.1X authentication.
IPv4 address	IPv4 address of the user. If the device does not get the IPv4 address of the user, this field is not available.
IPv6 address	IPv6 address of the user. If the device does not get the IPv6 address of the user, this field is not available.
Authentication method	EAP message handling method: · CHAP—Performs EAP termination and uses CHAP to communicate with the RADIUS server. · EAP—Relays EAP packets and supports any of the EAP authentication methods to communicate with the RADIUS server. · PAP—Performs EAP termination and uses PAP to communicate with the RADIUS server.
Initial VLAN	VLAN to which the user belongs before 802.1X authentication.
Authorization untagged VLAN	Untagged VLAN authorized to the user.
Authorization tagged VLAN list	Tagged VLANs authorized to the user.
Authorization ACL ID	ACL authorized to the user.
Termination action	Action attribute assigned by the server to terminate the user session: · Default—Logs off the online authenticated 802.1X user when the session timeout timer expires. This attribute does not take effect when 802.1X periodic reauthentication is enabled and the periodic reauthentication timer is shorter than the session timeout timer. · Radius-request—Reauthenticates the online user when the session timeout timer expires, regardless of whether the 802.1X periodic reauthentication feature is enabled or not. If the device performs local authentication, this field displays N/A.
Session timeout period	Session timeout timer assigned by the server. If the device performs local authentication, this field displays N/A.
Online from	Time from which the 802.1X user came online.
Online duration	Online duration of the 802.1X user.
Total xxx connections matched.	Number of online 802.1X users.

dot1x

Use dot1x to enable 802.1X globally or on a port.

Use undo dot1x to disable 802.1X globally or on a port.

Syntax

dot1x

undo dot1x

Default

802.1X is neither enabled globally nor enabled for any port.

Views

System view

Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

For the 802.1X feature to take effect on a port, you must enable the feature both globally and on the port.

Examples

# Enable 802.1X globally.

<Sysname> system-view

[Sysname] dot1x

# Enable 802.1X on Ten-GigabitEthernet 1/1/1.

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x

[Sysname-Ten-GigabitEthernet1/1/1] quit

Related commands

display dot1x

dot1x after-mac-auth max-attempt

Use dot1x after-mac-auth max-attempt to set the maximum number of 802.1X authentication attempts for MAC authenticated users on a port.

Use undo dot1x after-mac-auth max-attempt to restore the default.

Syntax

dot1x after-mac-auth max-attempt max-attemps

undo dot1x after-mac-auth max-attempt

Default

The number of 802.1X authentication attempts for MAC authenticated users is not limited on a port.

Views

Ethernet interface view

Predefined user roles

network-admin

Parameters

max-attempts: Specifies a number in the range of 1 to 50.

Usage guidelines

The device denies 802.1X authentication requests of a MAC authenticated user after the maximum number of 802.1X authentication attempts has been made.

The device will recount the number of 802.1X authentication attempts made by a MAC authenticated user if a user logoff or device reboot event occurs.

Examples

# Configure Ten-GigabitEthernet 1/1/1 to allow a maximum of 10 802.1X authentication attempts made by a MAC authenticated user.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x after-mac-auth max-attempt 10

dot1x authentication-method

Use dot1x authentication-method to specify an EAP message handling method.

Use undo dot1x authentication-method to restore the default.

Syntax

dot1x authentication-method { chap | eap | pap }

undo dot1x authentication-method

Default

The access device performs EAP termination and uses CHAP to communicate with the RADIUS server.

Views

System view

Predefined user roles

network-admin

Parameters

chap: Configures the access device to perform Extensible Authentication Protocol (EAP) termination and use the Challenge Handshake Authentication Protocol (CHAP) to communicate with the RADIUS server.

eap: Configures the access device to relay EAP packets, and supports any of the EAP authentication methods to communicate with the RADIUS server.

pap: Configures the access device to perform EAP termination and use the Password Authentication Protocol (PAP) to communicate with the RADIUS server.

Usage guidelines

The access device terminates or relays EAP packets.

· In EAP termination mode—The access device re-encapsulates and sends the authentication data from the client in standard RADIUS packets to the RADIUS server. The device performs either CHAP or PAP authentication with the RADIUS server. In this mode the RADIUS server supports only MD5-Challenge EAP authentication, and the username and password EAP authentication initiated by an iNode client.

¡ PAP transports usernames and passwords in plain text. The authentication method applies to scenarios that do not require high security. To use PAP, the client can be an H3C iNode 802.1X client.

¡ CHAP transports username in plaintext and encrypted password over the network. CHAP is more secure than PAP.

· In EAP relay mode—The access device relays EAP messages between the client and the RADIUS server. The EAP relay mode supports multiple EAP authentication methods, such as MD5-Challenge, EAP-TL, and PEAP. To use this mode, make sure the RADIUS server meets the following requirements:

¡ Supports the EAP-Message and Message-Authenticator attributes.

¡ Uses the same EAP authentication method as the client.

If this mode is used, the user-name-format command configured in RADIUS scheme view does not take effect. For more information about the user-name-format command, see "RADIUS commands."

If RADIUS authentication is used, you must configure the access device to use the same authentication method (PAP, CHAP, or EAP) as the RADIUS server.

Examples

# Enable the access device to terminate EAP packets and perform PAP authentication with the RADIUS server.

<Sysname> system-view

[Sysname] dot1x authentication-method pap

Related commands

display dot1x

dot1x auth-fail vlan

Use dot1x auth-fail vlan to configure an 802.1X Auth-Fail VLAN on a port.

Use undo dot1x auth-fail vlan to restore the default.

Syntax

dot1x auth-fail vlan authfail-vlan-id

undo dot1x auth-fail vlan

Default

No 802.1X Auth-Fail VLAN exists on a port.

Views

Ethernet interface view

Predefined user roles

network-admin

Parameters

authfail-vlan-id: Specifies the ID of the 802.1X Auth-Fail VLAN on the port. The value range for the VLAN ID is 1 to 4094. Make sure the VLAN has been created.

Usage guidelines

An 802.1X Auth-Fail VLAN accommodates users who have failed 802.1X authentication for any other reason than unreachable servers. Users in the Auth-Fail VLAN can access a limited set of network resources.

You cannot specify a VLAN as both a super VLAN and an 802.1X Auth-Fail VLAN on a port. For more information about super VLANs, see Layer 2—LAN Switching Configuration Guide.

To delete a VLAN that has been configured as an 802.1X Auth-Fail VLAN, you must first use the undo dot1x auth-fail vlan command.

Examples

# Configure VLAN 100 as the Auth-Fail VLAN on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x auth-fail vlan 100

Related commands

display dot1x

dot1x critical eapol

Use dot1x critical eapol to enable the sending of an EAP-Success packet to a client when the 802.1X client user is assigned to the 802.1X critical VLAN on a port.

Use undo dot1x critical eapol to restore the default.

Syntax

dot1x critical eapol

undo dot1x critical eapol

Default

The device sends an EAP-Failure packet to a client when the 802.1X client user is assigned to the 802.1X critical VLAN on a port.

Views

Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

This command allows specific 802.1X users in the critical VLAN to pass reauthentication directly when the device detects a reachable server. The device sends EAP-Success packets to the 802.1X clients that cannot respond to the EAP-Request packets of the device (for example, the Windows built-in 802.1X client).

Examples

# Send an EAP-Success packet to a client when the 802.1X client user is assigned to the 802.1X critical VLAN on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x critical eapol

Related commands

dot1x critical vlan

Use dot1x critical vlan to configure an 802.1X critical VLAN on a port.

Use undo dot1x critical vlan to restore the default.

Syntax

dot1x critical vlan critical-vlan-id

undo dot1x critical vlan

Default

No 802.1X critical VLAN exists on a port.

Views

Ethernet interface view

Predefined user roles

network-admin

Parameters

critical-vlan-id: Specifies the ID of the 802.1X critical VLAN on the port. The value range for the VLAN ID is 1 to 4094. Make sure the VLAN has been created.

Usage guidelines

An 802.1X critical VLAN accommodates users who fail 802.1X authentication because all the RADIUS servers in their ISP domains are unreachable. Users in the critical VLAN can access a limited set of network resources depending on the configuration.

You cannot specify a VLAN as both a super VLAN and an 802.1X critical VLAN on a port. For more information about super VLANs, see Layer 2—LAN Switching Configuration Guide.

To delete a VLAN that has been configured as an 802.1X critical VLAN, you must first use the undo dot1x critical vlan command.

Examples

# Specify VLAN 100 as the 802.1X critical VLAN on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x critical vlan 100

Related commands

display dot1x

dot1x critical-voice-vlan

Use dot1x critical-voice-vlan to enable the 802.1X critical voice VLAN on a port.

Use undo dot1x critical-voice-vlan to restore the default.

Syntax

dot1x critical-voice-vlan

undo dot1x critical-voice-vlan

Default

The 802.1X critical voice VLAN is disabled on a port.

Views

Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

The 802.1X critical voice VLAN on a port accommodates 802.1X voice users that have failed authentication because none of the RADIUS servers in their ISP domain are reachable.

Before you enable the 802.1X critical voice VLAN on the port, make sure the following requirements are met:

· The port is configured with the voice VLAN.

To configure a voice VLAN on a port, use the voice-vlan enable command (see Layer 2—LAN Switching Command Reference).

· LLDP is enabled both globally and on the port.

The device uses LLDP to identify voice users. For information about LLDP commands, see Layer 2—LAN Switching Command Reference.

Examples

# Enable the 802.1X critical voice VLAN on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x critical-voice-vlan

Related commands

display dot1x

lldp enable (Layer 2—LAN Switching Command Reference)

lldp global enable (Layer 2—LAN Switching Command Reference)

voice-vlan enable (Layer 2—LAN Switching Command Reference)

dot1x domain-delimiter

Use dot1x domain-delimiter to specify a set of domain name delimiters supported by the device.

Use undo dot1x domain-delimiter to restore the default.

Syntax

dot1x domain-delimiter string

undo dot1x domain-delimiter

Default

The device supports only the at sign (@) delimiter for 802.1X users.

Views

System view

Predefined user roles

network-admin

Parameters

string: Specifies a set of 1 to 16 domain name delimiters for 802.1X users. No space is required between delimiters. Available delimiters include the at sign (@), backslash (\), dot (.), and forward slash (/). If you want to use backslash (\) as the domain name delimiter, you must enter the escape character (\) along with the backslash (\) sign.

Usage guidelines

Any character in the configured set can be used as the domain name delimiter for 802.1X authentication users. Usernames that include domain names can use the format of username@domain-name, domain-name\username, username.domain-name, or username/domain-name.

The delimiter set you configured overrides the default setting. If the at sign (@) is not included in the delimiter set, the device does not support the 802.1X users who use this sign as the domain name delimiter.

If a username string contains multiple configured delimiters, the device takes the rightmost delimiter in the username string as the domain name delimiter. For example, if you configure the forward slash (/), dot (.), and backslash (\) as delimiters, the domain name delimiter for the username string 121.123/22\@abc is the backslash (\). The username is @abc and the domain name is 121.123/22.

Examples

# Specify the at sign (@) and forward slash (/) as domain name delimiters.

<Sysname> system-view

[Sysname] dot1x domain-delimiter @/

Related commands

display dot1x

dot1x ead-assistant enable

Use dot1x ead-assistant enable to enable the EAD assistant feature.

Use undo dot1x ead-assistant enable to disable the EAD assistant feature.

Syntax

dot1x ead-assistant enable

undo dot1x ead-assistant enable

Default

The EAD assistant feature is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

The EAD assistant feature enables the access device to redirect a user seeking to access the network to download and install EAD client. This feature eliminates the tedious job of the administrator to deploy EAD clients.

For the EAD assistant feature to take effect on a port, you must set the port authorization mode to auto.

The feature is mutually exclusive with MAC authentication and port security. You must disable MAC authentication and port security globally before you enable the EAD assistant feature.

Examples

# Enable the EAD assistant feature.

<Sysname> system-view

[Sysname] dot1x ead-assistant enable

Related commands

display dot1x

dot1x ead-assistant free-ip

dot1x ead-assistant url

dot1x ead-assistant free-ip

Use dot1x ead-assistant free-ip to configure a free IP.

Use undo dot1x ead-assistant free-ip to remove the specified or all free IP addresses.

Syntax

dot1x ead-assistant free-ip ip-address { mask-address | mask-length }

undo dot1x ead-assistant free-ip { ip-address { mask-address | mask-length } | all }

Default

No free IPs exist. Users cannot access any segments before they pass 802.1X authentication.

Views

System view

Predefined user roles

network-admin

Parameters

ip-address: Specifies a freely accessible IP address segment, also called a free IP.

mask: Specifies an IP address mask.

mask-length: Specifies IP address mask length in the range of 1 to 32.

all: Removes all free IP addresses.

Usage guidelines

With EAD assistant enabled on the device, unauthenticated 802.1X users can access the network resources in the free IP segments before they pass 802.1X authentication.

Execute this command multiple times to configure multiple free IPs.

Examples

# Configure 192.168.1.1/16 as a free IP.

<Sysname> system-view

[Sysname] dot1x ead-assistant free-ip 192.168.1.1 255.255.0.0

Related commands

display dot1x

dot1x ead-assistant enable

dot1x ead-assistant url

Use dot1x ead-assistant url to configure a redirect URL.

Use undo dot1x ead-assistant url to restore the default.

Syntax

dot1x ead-assistant url url-string

undo dot1x ead-assistant url

Default

No redirect URL exists.

Views

System view

Predefined user roles

network-admin

Parameters

url-string: Specifies the redirect URL, a case-sensitive string of 1 to 256 characters in the format http://string or https://string. If the specified URL does not start with http:// or https://, the URL is considered to start with http:// by default.

Usage guidelines

When an unauthenticated user uses a Web browser to access networks other than the free IP, the device redirects the user to the redirect URL.

The redirect URL must be on the free IP subnet.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Configure the redirect URL as http://test.com.

<Sysname> system-view

[Sysname] dot1x ead-assistant url http://test.com

Related commands

display dot1x

dot1x ead-assistant enable

dot1x ead-assistant free-ip

dot1x eapol untag

Use dot1x eapol untag to enable the device to send 802.1X protocol packets out of a port without VLAN tags.

Use undo dot1x eapol untag to restore the default.

Syntax

dot1x eapol untag

undo dot1x eapol untag

Default

The device can send 802.1X protocol packets out of a port with VLAN tags.

Views

Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

This command enables the device to send 802.1X protocol packets out of an 802.1X-enabled port without VLAN tags. It prevents terminal devices connected to the port from failing 802.1X authentication because they cannot identify VLAN tags.

This command applies only to Ethernet ports whose link type is hybrid or trunk.

Examples

# Enable the device to send 802.1X protocol packets out of Ten-GigabitEthernet 1/1/1 without VLAN tags.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x eapol untag

Related commands

display dot1x

dot1x guest-vlan

Use dot1x guest-vlan to configure an 802.1X guest VLAN on a port.

Use undo dot1x guest-vlan to restore the default.

Syntax

dot1x guest-vlan guest-vlan-id

undo dot1x guest-vlan

Default

No 802.1X guest VLAN exists on a port.

Views

Ethernet interface view

Predefined user roles

network-admin

Parameters

guest-vlan-id: Specifies the ID of the 802.1X guest VLAN. The value range for the VLAN ID is 1 to 4094. Make sure the VLAN has been created.

Usage guidelines

An 802.1X guest VLAN accommodates users who have not performed 802.1X authentication. In the guest VLAN, users can access a limited set of network resources, such as a software server, to download anti-virus software and system patches.

You cannot specify a VLAN as both a super VLAN and an 802.1X guest VLAN on a port. For more information about super VLANs, see Layer 2—LAN Switching Configuration Guide.

To delete a VLAN that has been configured as a guest VLAN, you must use the undo dot1x guest-vlan command first.

Examples

# Specify VLAN 100 as the 802.1X guest VLAN on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x guest-vlan 100

Related commands

display dot1x

dot1x guest-vlan-delay

Use dot1x guest-vlan-delay to enable 802.1X guest VLAN assignment delay on a port.

Use undo dot1x guest-vlan-delay to disable the specified 802.1X guest VLAN assignment delay on a port.

Syntax

dot1x guest-vlan-delay { eapol | new-mac }

undo dot1x guest-vlan-delay [ eapol | new-mac ]

Default

802.1X guest VLAN assignment delay is disabled on a port.

Views

Ethernet interface view

Predefined user roles

network-admin

Parameters

eapol: Specifies EAPOL-triggered 802.1X guest VLAN assignment delay. This keyword takes effect if 802.1X authentication is triggered by EAPOL-Start packets.

new-mac: Specifies new MAC-triggered 802.1X guest VLAN assignment delay. This keyword takes effect if 802.1X authentication is triggered by packets from unknown MAC addresses.

Usage guidelines

This command enables the device to delay assigning an 802.1X-enabled port to the 802.1X guest VLAN when 802.1X authentication is triggered on the port.

To use this feature, the 802.1X-enabled port must perform MAC-based access control.

When 802.1X authentication is triggered on a port, the device performs the following operations:

1. Sends a unicast EAP-Request/Identity packet to the MAC address that triggers the authentication.

2. Retransmits the packet if no response has been received within the username request timeout interval set by using the dot1x timer tx-period command.

3. Assigns the port the 802.1X guest VLAN after the maximum number of request attempts set by using the dot1x retry command is reached.

If you use the undo command without any keyword, the command disables both EAPOL-triggered and new MAC-triggered 802.1X guest VLAN assignment delay on a port.

Examples

# Enable EAPOL-triggered 802.1X guest VLAN assignment delay on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x guest-vlan-delay eapol

Related commands

display dot1x

dot1x guest-vlan

dot1x retry

dot1x timer tx-period

dot1x handshake

Use dot1x handshake to enable the online user handshake feature.

Use undo dot1x handshake to disable the online user handshake feature.

Syntax

dot1x handshake

undo dot1x handshake

Default

The online user handshake feature is enabled.

Views

Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

The online user handshake feature enables the device to periodically send EAP-Request/Identity packets to the client for verifying the connectivity status of online 802.1X users. The device sets a user to the offline state if it does not receive an EAP-Response/Identity packet from the user after making the maximum attempts within the handshake timer. To set the handshake timer, use the dot1x timer handshake-period command. To set the maximum handshake attempts, use the dot1x retry command.

Examples

# Enable the online user handshake feature on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x handshake

Related commands

display dot1x

dot1x timer handshake-period

dot1x retry

dot1x handshake reply enable

Use dot1x handshake reply enable to enable the 802.1X online user handshake reply feature.

Use undo dot1x handshake reply enable to disable the 802.1X online user handshake reply feature.

Syntax

dot1x handshake reply enable

undo dot1x handshake reply enable

Default

The 802.1X online user handshake reply feature is disabled.

Views

Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

This command enables the device to reply to 802.1X clients' EAP-Response/Identity packets with EAP-Success packets during the online handshake process.

Use this command only if 802.1X clients will go offline without receiving EAP-Success packets from the device.

Examples

# Enable the 802.1X online user handshake reply feature on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x handshake reply enable

Related commands

dot1x handshake

dot1x handshake secure

Use dot1x handshake secure to enable the online user handshake security feature.

Use undo dot1x handshake secure to disable the online user handshake security feature.

Syntax

dot1x handshake secure

undo dot1x handshake secure

Default

The online user handshake security feature is disabled.

Views

Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

The online user handshake security feature enables the device to prevent users from using illegal client software.

The feature is implemented based on the online user handshake feature. To bring the security function into effect, make sure the online user handshake feature is enabled.

The online user handshake security feature takes effect only on the network where the iNode client and IMC server are used.

Examples

# Enable the online user handshake security feature on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x handshake secure

Related commands

display dot1x

dot1x handshake

dot1x mandatory-domain

Use dot1x mandatory-domain to specify a mandatory 802.1X authentication domain on a port.

Use undo dot1x mandatory-domain to restore the default.

Syntax

dot1x mandatory-domain domain-name

undo dot1x mandatory-domain

Default

No mandatory 802.1X authentication domain is specified on a port.

Views

Ethernet interface view

Predefined user roles

network-admin

Parameters

domain-name: Specifies the ISP domain name, a case-insensitive string of 1 to 255 characters.

Usage guidelines

When the system authenticates an 802.1X user trying to access a port, it selects an authentication domain in the following order:

1. Mandatory domain.

2. ISP domain specified in the username.

3. Default ISP domain.

Examples

# Specify my-domain as the mandatory authentication domain for 802.1X users on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x mandatory-domain my-domain

Related commands

display dot1x

dot1x max-user

Use dot1x max-user to set the maximum number of concurrent 802.1X users on a port.

Use undo dot1x max-user to restore the default.

Syntax

dot1x max-user max-number

undo dot1x max-user

Default

The device allows a maximum of 4294967295 concurrent 802.1X users on a port.

Views

Ethernet interface view

Predefined user roles

network-admin

Parameters

max-number: Specifies the maximum number of concurrent 802.1X users on a port. The value range is 1 to 4294967295.

Usage guidelines

Set the maximum number of concurrent 802.1X users on a port to prevent the system resources from being overused. When the maximum number is reached, the port denies subsequent 802.1X users.

Examples

# Set the maximum number of concurrent 802.1X users to 32 on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x max-user 32

Related commands

display dot1x

dot1x multicast -trigger

Use dot1x multicast-trigger to enable the 802.1X multicast trigger feature.

Use undo dot1x multicast-trigger to disable the 802.1X multicast trigger feature.

Syntax

dot1x multicast-trigger

undo dot1x multicast-trigger

Default

The 802.1X multicast trigger feature is enabled.

Views

Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

The multicast trigger feature enables the device to act as the initiator. The device periodically multicasts EAP-Request/Identity packets out of a port to detect 802.1X clients and trigger authentication. You can use the dot1x timer tx-period command to set the interval for sending multicast EAP-Request/Identity packets.

Examples

# Enable the multicast trigger feature on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x multicast-trigger

Related commands

display dot1x

dot1x timer tx-period

dot1x unicast-trigger

dot1x port-control

Use dot1x port-control to set the authorization state for the port.

Use undo dot1x port-control to restore the default.

Syntax

dot1x port-control { authorized-force | auto | unauthorized-force }

undo dot1x port-control

Default

The default port authorization state is auto.

Views

Ethernet interface view

Predefined user roles

network-admin

Parameters

authorized-force: Places the port in authorized state, enabling users on the port to access the network without authentication.

auto: Places the port initially in unauthorized state to allow only EAPOL packets to pass, and places the port in authorized state after a user passes authentication. You can use this option in most scenarios.

unauthorized-force: Places the port in unauthorized state, denying any access requests from users on the port.

Usage guidelines

You can use this command to set the port authorization state to determine whether a client is granted access to the network.

Examples

# Set the authorization state of Ten-GigabitEthernet 1/1/1 to unauthorized-force.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x port-control unauthorized-force

Related commands

display dot1x

dot1x port-method

Use dot1x port-method to specify an access control method for the port.

Use undo dot1x port-method to restore the default.

Syntax

dot1x port-method { macbased | portbased }

undo dot1x port-method

Default

MAC-based access control applies.

Views

Ethernet interface view

Predefined user roles

network-admin

Parameters

macbased: Uses MAC-based access control on the port to separately authenticate each user attempting to access the network. Using this method, when an authenticated user logs off, no other online users are affected.

portbased: Uses port-based access control on the port. Using this method, once an 802.1X user passes authentication on the port, any subsequent user can access the network through the port without authentication. When the authenticated user logs off, all other users are logged off.

Examples

# Configure Ten-GigabitEthernet 1/1/1 to implement port-based access control.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x port-method portbased

Related commands

display dot1x

dot1x quiet-period

Use dot1x quiet-period to enable the quiet timer.

Use undo dot1x quiet-period to disable the quiet timer.

Syntax

dot1x quiet-period

undo dot1x quiet-period

Default

The quiet timer is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

When a client fails 802.1X authentication, the device must wait a period of time before it can process authentication requests from the client. You can use the dot1x timer quiet-period command to set the quiet timer.

Examples

# Enable the quiet timer and set the quiet timer to 100 seconds.

<Sysname> system-view

[Sysname] dot1x quiet-period

[Sysname] dot1x timer quiet-period 100

Related commands

display dot1x

dot1x timer

dot1x re-authenticate

Use dot1x re-authenticate to enable the 802.1X periodic reauthentication feature.

Use undo dot1x re-authenticate to disable the 802.1X periodic reauthentication feature.

Syntax

dot1x re-authenticate

undo dot1x re-authenticate

Default

The 802.1X periodic reauthentication feature is disabled.

Views

Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

Periodic reauthentication enables the access device to periodically authenticate online 802.1X users on a port. This feature tracks the connection status of online users and updates the authorization attributes assigned by the server, such as the ACL and VLAN.

You can use the dot1x timer reauth-period command to configure the interval for reauthentication.

Examples

# Enable the 802.1X periodic reauthentication feature on Ten-GigabitEthernet 1/1/1, and set the periodic reauthentication interval to 1800 seconds.

<Sysname> system-view

[Sysname] dot1x timer reauth-period 1800

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x re-authenticate

Related commands

display dot1x

dot1x timer

dot1x re-authenticate manual

Use dot1x re-authenticate manual to manually reauthenticate all online 802.1X users on a port.

Syntax

dot1x re-authenticate manual

Views

Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

After this command is executed, this device reauthenticates all online 802.1X users on a port. The command takes effect regardless of the server-assigned reauthentication attribute and the periodic reauthentication feature.

Examples

# Manually reauthenticate all online 802.1X users on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x re-authenticate manual

Related commands

dot1x re-authenticate

dot1x re-authenticate server-unreachable keep-online

Use dot1x re-authenticate server-unreachable keep-online to enable the keep-online feature on a port.

Use undo dot1x re-authenticate server-unreachable to restore the default.

Syntax

dot1x re-authenticate server-unreachable keep-online

undo dot1x re-authenticate server-unreachable

Default

The keep-online feature is disabled on a port. The device logs off online 802.1X authenticated users if no server is reachable for 802.1X reauthentication.

Views

Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

This feature keeps authenticated 802.1X users online when no server is reachable for 802.1X reauthentication.

Examples

# Enable the keep-online feature on Ten-GigabitEthernet 1/1/1 for 802.1X reauthentication.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x re-authenticate server-unreachable keep-online

Related commands

display dot1x

dot1x re-authenticate

dot1x retry

Use dot1x retry to set the maximum number of attempts for sending an authentication request to a client.

Use undo dot1x retry to restore the default.

Syntax

dot1x retry retries

undo dot1x retry

Default

A maximum of two attempts are made to send an authentication request to a client.

Views

System view

Predefined user roles

network-admin

Parameters

retries: Specifies the maximum number of attempts for sending an authentication request to a client. The value range is 1 to 10.

Usage guidelines

The access device retransmits an authentication request to a client in any of the following situations:

· The device does not receive any responses from the client within the username request timeout timer. The timer is set by using the dot1x timer tx-period tx-period-value command for the EAP-Request/Identity packet.

· The device does not receive any responses from the client within the client timeout timer. The timer is set by using the dot1x timer supp-timeout supp-timeout-value command for the EAP-Request/MD5-Challenge packet.

The access device stops retransmitting the request, if it has made the maximum number of request transmission attempts but still received no response.

Examples

# Set the maximum number of attempts to 9 for sending an authentication request to a client.

<Sysname> system-view

[Sysname] dot1x retry 9

Related commands

display dot1x

dot1x timer

dot1x smarton

Use dot1x smarton to enable the SmartOn feature on a port.

Use undo dot1x smarton to disable the SmartOn feature on a port.

Syntax

dot1x smarton

undo dot1x smarton

Default

The SmartOn feature is disabled on a port.

Views

Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

When a SmartOn-enabled port receives an EAPOL-Start packet from an 802.1X client, it sends a unicast EAP-Request/Notification packet to the client. The client will respond with an EAP-Response/Notification packet, which contains the SmartOn switch ID and the MD5 digest of the SmartOn password. The device compares the digest in the packet with the digest on the device. If they are the same, the device continues to perform 802.1X authentication for the client. Otherwise, the device denies the client's 802.1X authentication request.

The SmartOn feature and the online user handshake feature are mutually exclusive.

Examples

# Enable the SmartOn feature on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x smarton

Related commands

display dot1x

dot1x smarton switched

dot1x smarton password

Use dot1x smarton password to set a SmartOn password.

Use undo dot1x smarton password to restore the default.

Syntax

dot1x smarton password { cipher | simple } string

undo dot1x smarton password

Default

No SmartOn password is set.

Views

System view

Predefined user roles

network-admin

Parameters

cipher: Specifies a password in encrypted form.

simple: Specifies password in plaintext form. For security purposes, the password specified in plaintext form will be stored in encrypted form.

string: Specifies the password. Its plaintext form is a case-sensitive string of 1 to 16 characters. Its encrypted form is a case-sensitive string of 1 to 53 characters

Usage guidelines

The device checks the MD5 digest of the SmartOn password in each received EAP-Response/Notification packet. If the digest is different from the SmartOn password digest on the device, the device stops the 802.1X authentication process for the client that sends this packet.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Set the SmartOn password to abc in plaintext form.

<Sysname> system-view

[Sysname] dot1x smarton password simple abc

Related commands

display dot1x

dot1x smarton

dot1x smarton switched

dot1x smarton retry

Use dot1x smarton retry to set the maximum number of attempts for retransmitting an EAP-Request/Notification packet to a client.

Use undo dot1x smarton retry to restore the default.

Syntax

dot1x smarton retry retries

undo dot1x smarton retry

Default

A maximum of three attempts are made to retransmit an EAP-Request/Notification packet to a client.

Views

System view

Predefined user roles

network-admin

Parameters

retries: Specifies the maximum attempts for retransmitting an EAP-Request/Notification packet to a client. The value range is 1 to 10.

Usage guidelines

When the device sends an EAP-Request/Notification packet to the client, the SmartOn client timeout timer (set by using the dot1x smarton timer supp-timeout command) starts. If the device does not receive any EAP-Response/Notification packets from the client within the timer, it retransmits the EAP-Request/Notification packet to the client. After the device has made the maximum retransmission attempts but received no response, it stops the 802.1X authentication process for the client.

Examples

# Set the maximum attempts to 5 for retransmitting an EAP-Request/Notification packet.

<Sysname> system-view

[Sysname] dot1x smarton retry 5

Related commands

display dot1x

dot1x smarton timer supp-timeout

dot1x smarton switchid

Use dot1x smarton switchid to set a SmartOn switch ID.

Use undo dot1x smarton switchid to restore the default.

Syntax

dot1x smarton switchid switch-string

undo dot1x smarton switchid

Default

No SmartOn switch ID exists.

Views

System view

Predefined user roles

network-admin

Parameters

switch-string: Specifies the SmartOn switch ID, a case-sensitive string of 1 to 30 characters.

Usage guidelines

The device checks the SmartOn switch ID in each received EAP-Response/Notification packet. If the switch ID is not the same as the switch ID on the device, the device stops the 802.1X authentication process for the client that sends this packet.

Examples

# Set the SmartOn switch ID to abc.

<Sysname> system-view

[Sysname] dot1x smarton switchid abc

Related commands

display dot1x

dot1x smarton

dot1x smarton password

dot1x smarton timer supp-timeout

Use dot1x smarton timer supp-timeout to set the SmartOn client timeout timer.

Use undo dot1x smarton timer supp-timeout to restore the default.

Syntax

dot1x smarton timer supp-timeout supp-timeout-value

undo dot1x smarton timer supp-timeout

Default

The SmartOn client timeout timer is 30 seconds.

Views

System view

Predefined user roles

network-admin

Parameters

supp-timeout-value: Specifies the SmartOn client timeout timer in seconds. The value range is 10 to 120.

Usage guidelines

The SmartOn client timeout timer starts when the device sends an EAP-Request/Notification packet to the client. If the device does not receive any EAP-Response/Notification packets from the client within the timer interval, it retransmits the EAP-Request/Notification packet. After the device has made the maximum retransmission attempts but received no response, it stops the 802.1X authentication process for the client. To set the maximum retransmission attempts, use the dot1x smarton retry command.

Examples

# Set the SmartOn client timeout timer to 20 seconds.

<Sysname> system-view

[Sysname] dot1x smarton timer supp-timeout 20

Related commands

display dot1x

dot1x smarton retry

dot1x timer

Use dot1x timer to set an 802.1X timer.

Use undo dot1x timer to restore the default of an 802.1X timer.

Syntax

dot1x timer { ead-timeout ead-timeout-value | handshake-period handshake-period-value | quiet-period quiet-period-value | reauth-period reauth-period-value | server-timeout server-timeout-value | supp-timeout supp-timeout-value | tx-period tx-period-value }

undo dot1x timer { ead-timeout | handshake-period | quiet-period | reauth-period | server-timeout | supp-timeout | tx-period }

Default

The following 802.1X timers apply:

· EAD rule timer: 30 minutes.

· Handshake timer: 15 seconds.

· Quiet timer: 60 seconds.

· Periodic reauthentication timer: 3600 seconds.

· Server timeout timer: 100 seconds.

· Client timeout timer: 30 seconds.

· Username request timeout timer: 30 seconds.

Views

System view

Predefined user roles

network-admin

Parameters

ead-timeout ead-timeout-value: Specifies the EAD rule timer in minutes. The value range for the ead-timeout-value argument is 1 to 1440.

handshake-period handshake-period-value: Specifies the handshake timer in seconds. The value range for the handshake-period-value argument is 5 to 1024.

quiet-period quiet-period-value: Specifies the quiet timer in seconds. The value range for the quiet-period-value argument is 10 to 120.

reauth-period reauth-period-value: Specifies the periodic reauthentication timer in seconds. The value range for the reauth-period-value argument is 60 to 7200.

server-timeout server-timeout-value: Specifies the server timeout timer in seconds. The value range for the server-timeout-value argument is 100 to 300.

supp-timeout supp-timeout-value: Specifies the client timeout timer in seconds. The value range for the supp-timeout-value argument is 1 to 120.

tx-period tx-period-value: Specifies the username request timeout timer in seconds. The value range for the tx-period-value argument is 1 to 120.

Usage guidelines

In most cases, the default settings are sufficient. You can edit the timers, depending on the network conditions.

· In a low-speed network, increase the client timeout timer.

· In a vulnerable network, set the quiet timer to a high value.

· In a high-performance network with quick authentication response, set the quiet timer to a low value.

· In a network with authentication servers of different performance, adjust the server timeout timer.

The network device uses the following 802.1X timers:

· EAD rule timer (EAD timeout)—Sets the lifetime of each EAD rule. When the timer expires or the user passes authentication, the rule is removed. If users fail to download the EAD client or fail to pass authentication within the timer, they must reconnect to the network to access the free IP.

· Handshake timer (handshake-period)—Sets the interval at which the access device sends client handshake requests to check the online status of a client that has passed authentication. If the device does not receive a response after sending the maximum number of handshake requests, it considers that the client has logged off.

· Quiet timer (quiet-period)—Starts when a client fails authentication. The access device must wait the time period before it can process the authentication attempts from the client.

· Periodic reauthentication timer (reauth-period)—Sets the interval at which the network device periodically reauthenticates online 802.1X users. To enable 802.1X periodic reauthentication on a port, use the dot1x re-authenticate command.

· Server timeout timer (server-timeout)—Starts when the access device sends a RADIUS Access-Request packet to the authentication server. If no response is received when this timer expires, the access device retransmits the request to the server.

· Client timeout timer (supp-timeout)—Starts when the access device sends an EAP-Request/MD5-Challenge packet to a client. If no response is received when this timer expires, the access device retransmits the request to the client.

· Username request timeout timer (tx-period)—Starts when the device sends an EAP-Request/Identity packet to a client in response to an authentication request. If the device does not receive a response before this timer expires, it retransmits the request. The timer also sets the interval at which the network device sends multicast EAP-Request/Identity packets to detect clients that cannot actively request authentication.

The change to the periodic reauthentication timer applies to the users who have been online only after the old timer expires. Other timer changes take effect immediately on the device.

Examples

# Set the server timeout timer to 150 seconds.

<Sysname> system-view

[Sysname] dot1x timer server-timeout 150

Related commands

display dot1x

dot1x timer reauth-period

Use dot1x timer reauth-period to set the 802.1X periodic reauthentication timer on a port.

Use undo dot1x timer reauth-period to restore the default.

Syntax

dot1x timer reauth-period reauth-period-value

undo dot1x timer reauth-period

Default

No 802.1X periodic reauthentication timer is configured on a port. The port uses the global 802.1X periodic reauthentication timer.

Views

Ethernet interface view

Predefined user roles

network-admin

Parameters

reauth-period-value: Specifies the 802.1X periodic reauthentication timer in seconds. The value range for the reauth-period-value argument is 60 to 7200.

Usage guidelines

The device reauthenticates online 802.1X users on a port at the specified periodic reauthentication interval when the port is enabled with periodic reauthentication. To enable periodic reauthentication on a port, use the dot1x re-authenticate command.

A change to the periodic reauthentication timer applies to online users only after the old timer expires.

The device selects a periodic reauthentication timer for 802.1X reauthentication in the following order:

1. Server-assigned reauthentication timer.

2. Port-specific reauthentication timer.

3. Global reauthentication timer.

4. Default reauthentication timer.

Examples

# Set the 802.1X periodic reauthentication timer to 60 seconds on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1 1/0/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x timer reauth-period 60

Related commands

dot1x timer

dot1x unicast-trigger

Use dot1x unicast-trigger to enable the 802.1X unicast trigger feature.

Use undo dot1x unicast-trigger to disable the 802.1X unicast trigger feature.

Syntax

dot1x unicast-trigger

undo dot1x unicast-trigger

Default

The 802.1X unicast trigger feature is disabled.

Views

Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

The unicast trigger feature enables the access device to initiate 802.1X authentication when the device receives a data frame from an unknown source MAC address. The device sends a unicast EAP-Request/Identity packet to the unknown source MAC address. It will retransmit the packet if it does not receive any responses within a period of time (set by using the dot1x timer tx-period command). This process continues until the maximum number of request attempts (set by using the dot1x retry command) is reached.

Examples

# Enable the unicast trigger feature on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x unicast-trigger

Related commands

display dot1x

dot1x multicast-trigger

dot1x retry

dot1x timer

dot1x user-ip freeze

Use dot1x user-ip freeze to enable 802.1X user IP freezing.

Use undo dot1x user-ip freeze to disable 802.1X user IP freezing.

Syntax

dot1x user-ip freeze

undo dot1x user-ip freeze

Default

802.1X user IP freezing is disabled.

Views

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

This command prevents 802.1X-generated IPSG bindings from being updated because of user IP changes. For information about IP source guard commands, see "IP source guard commands."

Examples

# Enable 802.1X user IP freezing on Ten-GigabitEthernet 1/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/1/1

[Sysname-Ten-GigabitEthernet1/1/1] dot1x user-ip freeze

reset dot1x guest-vlan

Use reset dot1x guest-vlan to remove users from the 802.1X guest VLAN on a port.

Syntax

reset dot1x guest-vlan interface interface-type interface-number [ mac-address mac-address ]

Views

User view

Predefined user roles

network-admin

Parameters

interface interface-type interface-number: Specifies a port by its type and number.

mac-address mac-address: Specifies the MAC address of an 802.1X user in the guest VLAN. If you do not specify this option, the command removes all 802.1X users from the 802.1X guest VLAN on the port.

Examples

# Remove the 802.1X user with MAC address 1-1-1 from the 802.1X guest VLAN on Ten-GigabitEthernet 1/1/1.

<Sysname> reset dot1x guest-vlan interface ten-gigabitethernet 1/1/1 mac-address 1-1-1

Related commands

dot1x guest-vlan

reset dot1x statistics

Use reset dot1x statistics to clear 802.1X statistics.

Syntax

reset dot1x statistics [ interface interface-type interface-number ]

Views

User view

Predefined user roles

network-admin

Parameters

interface interface-type interface-number: Specifies a port by its type and number. If you do not specify a port, this command clears 802.1X statistics on all ports.

Examples

# Clear 802.1X statistics on Ten-GigabitEthernet 1/1/1.

<Sysname> reset dot1x statistics interface ten-gigabitethernet 1/1/1

Related commands

display dot1x

10-Security Command Reference

802.1X commands

dot1x auth-fail vlan

dot1x handshake secure

dot1x multicast-trigger

dot1x port-control

dot1x quiet-period

dot1x re-authenticate

dot1x smarton password

dot1x user-ip freeze

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

News & Events

Contact Us

dot1x multicast -trigger