Contents

Policy-based routing commands· 1

apply next-hop· 1

display ip policy-based-route· 1

display ip policy-based-route interface· 2

display ip policy-based-route local 4

display ip policy-based-route setup· 5

if-match acl 6

ip local policy-based-route· 7

ip policy-based-route· 7

policy-based-route· 8

reset ip policy-based-route statistics· 9

 

Policy-based routing commands

apply next-hop

Use apply next-hop to set a next hop.

Use undo apply next-hop to remove the configuration.

Syntax

apply next-hop [ vpn-instance vpn-instance-name ] { ip-address [ direct ] [ track track-entry-number ] }&<1-2>

undo apply next-hop [ [ vpn-instance vpn-instance-name ] ip-address&<1-2> ]

Default

No next hop is set.

Views

Policy node view

Predefined user roles

network-admin

mdc-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. The specified VPN must already exist. The vpn-instance vpn-instance-name option is not supported in the current software version.

ip-address: Specifies the IP address of the next hop.

direct: Specifies that the next hop must be directly connected to take effect.

track track-entry-number: Specifies a track entry by its number in the range of 1 to 1024.

&<1-2>: Indicates that the argument before it can be entered twice at most.

Usage guidelines

You can specify a maximum of two next hops for backup in one command line or by executing this command twice.

With a next hop specified, the undo apply next-hop command removes the next hop.

Without any next hop specified, the undo apply next-hop command removes all next hops.

Examples

# Set a directly-connected next hop of 1.1.1.1.

<Sysname> system-view

[Sysname] policy-based-route aa permit node 11

[Sysname-pbr-aa-11] apply next-hop 1.1.1.1 direct

display ip policy-based-route

Use display ip policy-based-route to display PBR policy information.

Syntax

display ip policy-based-route [ policy policy-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

policy policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters.

Usage guidelines

If no policy is specified, this command displays information about all policies.

If a policy name is specified, this command displays information about the specified policy.

Examples

# Display all policy information.

<Sysname> display ip policy-based-route

Policy name: aaa

  node 1 permit:

    if-match acl 2000

    apply next-hop 1.1.1.1

Table 1 Command output

Field	Description
node 1 permit	The match mode of Node 1 is permit.
if-match acl	Compares packets with the ACL.
apply next-hop	Specifies a next hop for permitted packets.

 

Related commands

policy-based-route

display ip policy-based-route interface

Use display ip policy-based-route interface to display interface PBR configuration and statistics.

Syntax

In standalone mode:

display ip policy-based-route interface interface-type interface-number [ slot slot-number ]

In IRF mode:

display ip policy-based-route interface interface-type interface-number [ chassis chassis-number slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number.

slot slot-number: Displays the PBR configuration and statistics on a card. The slot-number argument is the number of the slot that holds the card. (In standalone mode.)

chassis chassis-number slot slot-number: Displays the PBR configuration and statistics for a card on an IRF member device. The chassis-number argument is the ID of the IRF member device. The slot-number argument is the number of the slot that holds the card. (In IRF mode.)

Examples

# Display PBR configuration and statistics on GigabitEthernet 1/0/1.

<Sysname> display ip policy-based-route interface gigabitethernet 1/0/1

Policy based routing information for interface GigabitEthernet1/0/1(failed):

Policy name: aaa

  node 0 deny:

  Matched: 0

  node 1 permit:

    if-match acl 3999

  Matched: 0

  node 2 permit:

    if-match acl 2000

    apply next-hop 2.2.2.2

  Matched: 0

Total matched: 0

<Sysname> display ip policy-based-route interface gigabitethernet 1/0/1

Policy based routing information for interface GigabitEthernet1/0/1:

Policy name: aaa

  node 0 deny(not support):

  Matched: 0

  node 1 permit:

    if-match acl 3999

  Matched: 0

  node 5 permit:

    if-match acl 3101

    apply next-hop 1.1.1.1

  Matched: 0 (no statistics resource)

Total matched: 0

Table 2 Command output

Field	Description
Policy based routing information for interface GigabitEthernet1/0/1(failed)	PBR configuration and statistics on GigabitEthernet 1/0/1. failed indicates that the policy (including all its nodes) failed to be assigned to the driver. For a global interface (with only a one-dimensional interface number, for example, VLAN-interface 10), failed can be displayed only when you specify the slot slot-number or chassis chassis-number slot slot-number option for the command.
node 0 deny(not support) node 2 permit(no resource)	Match mode of the node, permit or deny. not support means the device does not support match criteria configured on the node. no resource means the device has insufficient ACL resources, and failed to assign ACL resources to the node. For a global interface (with only a one-dimensional interface number, for example, VLAN-interface 10), not support and no resource can be displayed only when you specify the slot slot-number or chassis chassis-number slot slot-number option for the command.
if-match acl	Compares packets with the ACL.
apply next-hop	Specifies a next hop for permitted packets.
Matched: 0 (no statistics resource)	Number of successful matches on the node (no statistics resource indicates insufficient statistics resources). For a global interface (with only a one-dimensional interface number, for example, VLAN-interface 10), no statistics resource can be displayed only when you specify the slot slot-number or chassis chassis-number slot slot-number option for the command.
Total matched	Total number of successful matches on all nodes.

 

Related commands

reset ip policy-based-route statistics

display ip policy-based-route local

Use display ip policy-based-route local to display local PBR configuration and statistics.

Syntax

In standalone mode:

display ip policy-based-route local [ slot slot-number ]

In IRF mode:

display ip policy-based-route local [ chassis chassis-number slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

slot slot-number: Displays the PBR configuration and statistics on a card. The slot-number argument is the number of the slot that holds the card. (In standalone mode.)

chassis chassis-number slot slot-number: Displays the PBR configuration and statistics for a card on an IRF member device. The chassis-number argument is the ID of the IRF member device. The slot-number argument is the number of the slot that holds the card. (In IRF mode.)

Examples

# Display local PBR configuration and statistics.

<Sysname> display ip policy-based-route local

Policy based routing information for local:

Policy name: aaa

  node 0 deny:

  Matched: 0

  node 1 permit:

    if-match acl 3999

  Matched: 0

  node 2 permit:

    if-match acl 2000

    apply next-hop 2.2.2.2

  Matched: 0

  node 5 permit:

    if-match acl 3101

    apply next-hop 1.1.1.1

  Matched: 0

Total matched: 0

Table 3 Command output

Field	Description
Policy based routing information for local	Local PBR configuration and statistics.
node 0 deny/node 2 permit	Match mode of the node: permit or deny.
if-match acl	Compares packets with the ACL.
apply next-hop	Specifies a next hop for permitted packets.
Matched: 0	Number of successful matches on the node.
Total matched	Total number of successful matches on all nodes.

 

Related commands

reset ip policy-based-route statistics

display ip policy-based-route setup

Use display ip policy-based-route setup to display PBR configuration.

Syntax

display ip policy-based-route setup

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Examples

# Display PBR configuration.

<Sysname> display ip policy-based-route setup

Policy Name              Interface Name

pr01                     GigabitEthernet 1/0/1

Table 4 Command output

Field	Description
Interface Name	Interface where the policy is applied.

 

Related commands

ip policy-based-route

if-match acl

Use if-match acl to set an ACL match criterion.

Use undo if-match acl to remove the ACL match criterion.

Syntax

if-match acl { acl-number | name acl-name }

undo if-match acl

Default

No ACL match criterion is set.

Views

Policy node view

Predefined user roles

network-admin

mdc-admin

Parameters

acl-number: Specifies an ACL by its number in the range of 2000 to 2999 for a basic ACL, and in the range of 3000 to 3999 for an advanced ACL.

name acl-name: Specifies an ACL by its name, a case-insensitive string of 1 to 63 characters starting with letter a to z or A to Z. The ACL name cannot be all.

Examples

# Configure Node 11 of policy aa to permit the packets matching ACL 2011.

<Sysname> system-view

[Sysname] policy-based-route aa permit node 11

[Sysname-pbr-aa-11] if-match acl 2011

# Configure Node 11 of policy aa to permit the packets matching ACL aaa.

<Sysname> system-view

[Sysname] policy-based-route aa permit node 11

[Sysname-pbr-aa-11] if-match acl name aaa

ip local policy-based-route

Use ip local policy-based-route to configure local PBR based on a policy.

Use undo ip local policy-based-route to remove the configuration.

Syntax

ip local policy-based-route policy-name

undo ip local policy-based-route

Default

No policy is referenced for local PBR.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters. The specified policy must already exist.

Usage guidelines

You can apply only one policy locally. Before you apply a new policy, you must first remove the current policy.

Local PBR is used to route locally generated packets. This feature might affect local services, such as ping and Telnet. Do not configure local PBR unless doing so is required.

Examples

# Configure local PBR based on policy aaa.

<Sysname> system-view

[Sysname] ip local policy-based-route aaa

Related commands

·     display ip policy-based-route setup

·     policy-based-route

ip policy-based-route

Use ip policy-based-route to configure interface PBR by applying a policy to an interface.

Use undo ip policy-based-route to remove the configuration.

Syntax

ip policy-based-route policy-name

undo ip policy-based-route

Default

No policy is applied to an interface.

Views

Interface view

Predefined user roles

network-admin

mdc-admin

Parameters

policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters. The specified policy must already exist.

Usage guidelines

You can apply only one policy to an interface. Before you apply a new policy, you must first remove the current policy from the interface.

Examples

# Apply policy aaa to VLAN-interface 2.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-Vlan2] interface vlan-interface 2

[Sysname-Vlan-interface2] ip policy-based-route aaa

Related commands

·     display ip policy-based-route setup

·     policy-based-route

policy-based-route

Use policy-based-route to create a policy node and enter policy node view.

Use undo policy-based-route to remove a policy or policy node.

Syntax

policy-based-route policy-name [ deny | permit ] node node-number

undo policy-based-route policy-name [ deny | node node-number | permit ]

Default

No policy node is created.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters.

deny: Specifies the match mode for the policy node as deny.

permit: Specifies the match mode for the policy node as permit (default mode).

node node-number: Specifies a policy node by its number in the range of 0 to 255. A smaller number has a higher priority.

Usage guidelines

A policy that has been applied to an interface or locally cannot be removed. To remove it, you must first cancel the application.

·     If a policy node is specified, the undo policy-based-route command removes the specified policy node.

·     If a match mode is specified, the command removes all nodes configured with the match mode.

·     If no policy node or match mode is specified, the command removes the whole policy.

Examples

# Create permit-mode of Node 10 for policy policy1 and enter policy node view.

<Sysname> system-view

[Sysname] policy-based-route policy1 permit node 10

[Sysname-pbr-policy1-10]

Related commands

display ip policy-based-route

reset ip policy-based-route statistics

Use reset ip policy-based-route statistics to clear PBR statistics.

Syntax

reset ip policy-based-route statistics [ policy policy-name ]

Views

User view

Predefined user roles

network-admin

mdc-admin

Parameters

policy policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters.

Usage guidelines

If no policy is specified, the command clears all PBR statistics.

If a policy is specified, the command clears the PBR statistics for the specified policy.

To view PBR statistics, use the display ip policy-based-route interface command.

Examples

# Clear all PBR statistics.

<Sysname> reset ip policy-based-route statistics

Related commands

·     display ip policy-based-route interface

·     display ip policy-based-route local