Contents

MSDP commands· 1

cache-sa-enable· 1

display msdp brief 1

display msdp peer-status· 3

display msdp sa-cache· 6

display msdp sa-count 7

encap-data-enable· 8

import-source· 9

msdp· 10

originating-rp· 11

peer 11

peer description· 12

peer mesh-group· 12

peer minimum-ttl 13

peer password· 14

peer request-sa-enable· 14

peer sa-cache-maximum·· 15

peer sa-policy· 16

peer sa-request-policy· 17

reset msdp peer 18

reset msdp sa-cache· 18

reset msdp statistics· 19

shutdown (MSDP view) 19

static-rpf-peer 20

timer retry· 21

 

MSDP commands

cache-sa-enable

Use cache-sa-enable to enable the SA message cache mechanism to cache the (S, G) entries contained in SA messages.

Use undo cache-sa-enable to disable the SA message cache mechanism.

Syntax

cache-sa-enable

undo cache-sa-enable

Default

The SA message cache mechanism is enabled, and the device caches the (S, G) entries contained in received SA messages.

Views

MSDP view

Predefined user roles

network-admin

Examples

# Enable the SA message cache mechanism on the public network, so that the device caches the (S, G) entries contained in the received SA messages.

<Sysname> system-view

[Sysname] msdp

[Sysname-msdp] cache-sa-enable

Related commands

·     display msdp sa-cache

·     display msdp sa-count

display msdp brief

Use display msdp brief to display brief information about MSDP peers.

Syntax

display msdp [ vpn-instance vpn-instance-name ] brief [ state { connect | disabled | established | listen | shutdown } ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays brief information about MSDP peers on the public network.

state: Specifies a state. If you do not specify this keyword, the command displays brief information about MSDP peers in all states.

connect: Specifies the connecting state.

disabled: Specifies the connection failure state.

established: Specifies the session state.

listen: Specifies the listening state.

shutdown: Specifies the shutdown state.

Examples

# Display brief information about MSDP peers in all states on the public network.

<Sysname> display msdp brief

Configured   Established  Listen       Connect      Shutdown     Disabled

1            1            0            0            0            0

 

Peer address    State       Up/Down time    AS         SA count   Reset count

20.20.20.20     Established 00:00:13        100        0          0

Table 1 Command output

Field	Description
Configured	Number of MSDP peers that have been configured.
Established	Number of MSDP peers in established state.
Listen	Number of MSDP peers in listening state.
Connect	Number of MSDP peers in connecting state.
Shutdown	Number of MSDP peers in shutdown state.
Disabled	Number of MSDP peers in disabled state.
Peer address	MSDP peer address.
State	MSDP peer status: ·     Established—A session has been established and the MSDP peer is in session. ·     Listen—A session has been established and the local device acts as the server in listening state. ·     Connect—A session is not established and the local device acts as a client in connecting state. ·     Shutdown—The session has been torn down. ·     Down—The connection failed.
Up/Down time	Length of time since the MSDP peering connection was established or torn down.
AS	Number of the AS where the MSDP peer is located. If the system could not obtain the AS number, this field displays a question mark (?).
SA count	Number of (S, G) entries in the SA cache.
Reset count	MSDP peering connection reset times.

 

display msdp peer-status

Use display msdp peer-status to display detailed status of MSDP peers.

Syntax

display msdp [ vpn-instance vpn-instance-name ] peer-status [ peer-address ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays detailed status of the MSDP peers on the public network.

peer-address: Specifies an MSDP peer by its address. If you do not specify an MSDP peer, this command displays the detailed status of all MSDP peers.

Examples

# Display detailed status of MSDP peer 20.20.20.20 on the public network.

<Sysname> display msdp peer-status 20.20.20.20

MSDP peer 20.20.20.20; AS 100

 Description:

 Information about connection status:

   State: Disabled

   Up/down time: 14:41:08

   Resets: 0

   Connection interface: LoopBack0 (20.20.20.30)

   Received/sent messages: 867/867

   Discarded input messages: 0

   Discarded output messages: 0

   Elapsed time since last connection or counters clear: 14:42:40

   Mesh group peer joined: momo

   Last disconnect reason: Hold timer expired with truncated message

   Truncated packet: 5 bytes in buffer, type: 1, length: 20, without packet time: 75s

 Information about (Source, Group)-based SA filtering policy:

   Import policy: None

   Export policy: None

 Information about SA-Requests:

   Policy to accept SA-Requests: None

   Sending SA-Requests status: Disable

 Minimum TTL to forward SA with encapsulated data: 0

 SAs learned from this peer: 0, SA cache maximum for the peer: 4294967295

 Input queue size: 0, Output queue size: 0

 Counters for MSDP messages:

   RPF check failure: 0

   Incoming/outgoing SA: 0/0

   Incoming/outgoing SA-Request: 0/0

   Incoming/outgoing SA-Response: 0/0

   Incoming/outgoing Keepalive: 867/867

   Incoming/outgoing Notification: 0/0

   Incoming/outgoing Traceroutes in progress: 0/0

   Incoming/outgoing Traceroute reply: 0/0

   Incoming/outgoing Unknown: 0/0

   Incoming/outgoing data packet: 0/0

Table 2 Command output

Field	Description
MSDP peer	MSDP peer address.
AS	Number of the AS where the MSDP peer is located. If the system could not obtain the AS number, this field displays a question mark (?).
State	MSDP peer status: ·     Established—A session has been established and the MSDP peer is in session. ·     Listen—A session has been established and the local device acts as the server in listening state. ·     Connect—A session is not established and the local device acts as a client in connecting state. ·     Shutdown—The session has been torn down. ·     Disabled—The connection failed.
Up/Down time	Length of time since the MSDP peering connection was established or torn down.
Resets	MSDP peering connection reset times.
Connection interface	Interface and IP address used for setting up a TCP connection with the remote MSDP peer.
Received/sent messages	Number of SA messages sent and received through this connection.
Discarded input messages	Number of discarded incoming messages.
Discarded output messages	Number of discarded outgoing messages.
Elapsed time since last connection or counters clear	Elapsed time since the MSDP peer information was last cleared.
Mesh group peer joined	Mesh group that the MSDP peer has joined. This field is not displayed if the MSDP peer does not join a mesh group.
Last disconnect reason	Reason why last MSDP peering connection was torn down. If the connection is not terminated, this field does not display any value. ·     Hold timer expired without message—Hold timer expires and the receiving cache has no messages. ·     Hold timer expired with truncated message—Hold timer expires and messages in the receiving buffer are not intact. ¡     bytes in buffer—Size of data in the receiving buffer when the connection was terminated. ¡     type—Type of packets in the receiving buffer when the connection was terminated. ¡     length—Length of packets in the receiving buffer when the connection was terminated. If the packet is too small in size, this field cannot be resolved and is not displayed. ¡     without packet time—Length of time since packets were last processed. ·     Remote peer has been closed—The MSDP peering connection has been torn down. ·     TCP ERROR/HUP event received—Error/hup event received by the TCP socket when the MSDP peer sent messages. ·     Illegal message received—The MSDP peer received illegal messages. ·     Notification received—The MSDP peer received notification messages. ·     Reset command executed—The user executed the reset msdp peer command. ·     Shutdown command executed—The user executed the shutdown command. ·     Interface downed—The MSDP peer received the interface down event when connecting to the remote MSDP peer.
Information about (Source, Group)-based SA filtering policy	SA message filtering list information: ·     Import policy—Filter list for receiving SA messages from the specified MSDP peer. ·     Export policy—Filter list for forwarding SA messages from the specified MSDP peer.
Information about SA-Requests	SA request information: ·     Policy to accept SA request messages—Filtering rule for receiving or forwarding SA request messages from the specified MSDP peer. If SA request messages are not filtered, this field displays None. ·     Sending SA requests status—Whether the MSDP peer is enabled to send an SA request message to the designated MSDP peer after receiving a new join message.
Minimum TTL to forward SA with encapsulated data	Lower TTL threshold for the multicast packets encapsulated in SA messages.
SAs learned from this peer	Number of cached (S, G) entries learned from the specified MSDP peer.
SA-cache maximum for the peer	Maximum number of (S, G) entries learned from the specified MSDP peer that the device can cache.
Input queue size	Data size cached in the input queue.
Output queue size	Data size cached in the output queue.
Counters for MSDP message	MSDP peer statistics: ·     RPF check failure—Number of SA messages discarded because of RPF check failure. ·     Incoming/outgoing SA—Number of received and sent SA messages. ·     Incoming/outgoing SA-Request—Number of received and sent SA requests. ·     Incoming/outgoing SA-Response—Number of received and sent SA responses. ·     Incoming/outgoing Keepalive—Number of received and sent keepalive messages. ·     Incoming/outgoing Notification—Number of received and sent notification messages. ·     Incoming/outgoing Traceroutes in progress—Number of received and sent traceroute-in-progress messages. ·     Incoming/outgoing Traceroute reply—Number of received and sent traceroute replies. ·     Incoming/outgoing Unknown—Number of received and sent unknown messages. ·     Incoming/outgoing data packet—Number of received and sent SA messages encapsulated with multicast data.

 

display msdp sa-cache

Use display msdp sa-cache to display (S, G) entries in the SA cache.

Syntax

display msdp [ vpn-instance vpn-instance-name ] sa-cache [ group-address | source-address | as-number ] *

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays (S, G) entries in the SA cache on the public network.

group-address: Specifies a multicast group by its IP address in the range of 224.0.1.0 to 239.255.255.255. If you do not specify a multicast group, this command displays (S, G) entries in the SA cache for all multicast groups.

source-address: Specifies a multicast source by its IP address. If you do not specify a multicast source, this command displays (S, G) entries in the SA cache for all sources.

as-number: Specifies an AS number in the range of 1 to 4294967295. If you do not specify an AS number, this command displays (S, G) entries in the SA cache for all ASs.

Usage guidelines

You must execute the cache-sa-enable command before you execute this command. Otherwise, this command does not display any output.

Examples

# Display (S, G) entries in the SA cache on the public network.

<Sysname> display msdp sa-cache

Total Source-Active Cache - 5 entries

Matched 5 entries

 

Source          Group           Origin RP       Pro  AS         Uptime   Expires

10.10.1.2       225.0.0.1       10.10.10.10     BGP  100        00:00:11 00:05:49

10.10.1.2       225.0.0.2       10.10.10.10     BGP  100        00:00:11 00:05:49

10.10.1.2       225.0.0.3       10.10.10.10     BGP  100        00:00:11 00:05:49

10.10.1.2       225.0.0.4       10.10.10.10     BGP  100        00:00:11 00:05:49

10.10.1.2       225.0.0.5       10.10.10.10     BGP  100        00:00:11 00:05:49

Table 3 Command output

Field	Description
Total Source-Active Cache	Total number of multicast sources in the SA cache.
Matched	Total number of (S, G) entries that match a multicast sources.
Source	Multicast source address.
Group	Multicast group address.
Origin RP	Address of the RP that generated the (S, G) entry.
Pro	Type of protocol from which the AS number of the origin RP originates. If the system could not obtain the AS number, this field displays a question mark (?).
AS	AS number of the origin RP. If the system could not obtain the AS number, this field displays a question mark (?).
Uptime	Length of time for which the cached (S, G) entry has existed.
Expires	Length of time in which the cached (S, G) entry will expire.

 

Related commands

cache-sa-enable

display msdp sa-count

Use display msdp sa-count to display the number of (S, G) entries in the SA cache.

Syntax

display msdp [ vpn-instance vpn-instance-name ] sa-count [ as-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays the number of (S, G) entries in the SA cache on the public network.

as-number: Specifies an AS number in the range of 1 to 4294967295. If you do not specify an AS number, this command displays the number of (S, G) entries in the SA cache for all ASs.

Usage guidelines

This command displays the output only after you execute the cache-sa-enable command.

Examples

# Display the number of (S, G) entries in the SA cache on the public network.

<Sysname> display msdp sa-count

(S, G) entries statistics, counted by peer

  Peer address       SA count

  10.10.10.10        5

 

(S, G) entries statistics, counted by AS

  AS         Source count        Group count

  ?          3                   3

 

5 (S, G) entries in total

Table 4 Command output

Field	Description
(S, G) entries statistics, counted by peer	Number of (S, G) entries on an MSDP peer basis.
Peer address	Address of the MSDP peer that sent SA messages.
SA count	Number of (S, G) entries from this MSDP peer.
(S, G) entries statistics, counted by AS	Number of cached (S, G) entries on an AS basis.
AS	AS number. If the system could not obtain the AS number, this field displays a question mark (?).
Source count	Number of multicast sources in this AS.
Group count	Number of multicast groups in this AS.
(S, G) entries in total	Total number of (S, G) entries.

 

Related commands

cache-sa-enable

encap-data-enable

Use encap-data-enable to enable multicast data encapsulation in SA messages.

Use undo encap-data-enable to restore the default.

Syntax

encap-data-enable

undo encap-data-enable

Default

An SA message contains only (S, G) entries. Multicast data is not encapsulated in an SA message.

Views

MSDP view

Predefined user roles

network-admin

Examples

# Enable multicast data encapsulation in SA messages on the public network.

<Sysname> system-view

[Sysname] msdp

[Sysname-msdp] encap-data-enable

import-source

Use import-source to configure an SA message creation policy.

Use undo import-source to remove the configured SA message creation policy.

Syntax

import-source [ acl acl-number ]

undo import-source

Default

When an SA message is created, all the (S, G) entries within the domain are advertised in the SA message.

Views

MSDP view

Predefined user roles

network-admin

Parameters

acl-number: Specifies an IPv4 basic or advanced ACL number in the range of 2000 to 3999. If you specify an ACL, this command advertises only the (S, G) entries that the ACL permits. The command does not advertise any (S, G) entries when one of the following conditions exists:

·     You do not specify an ACL.

·     The specified ACL does not exist.

·     The specified ACL does not have any valid rules.

Usage guidelines

This command controls the creation of SA messages. To control forwarding or acceptance of SA messages, use the peer sa-policy command.

When you configure a rule in the IPv4 ACL, follow these restrictions and guidelines:

·     For the rule to take effect, do not specify the vpn-instance vpn-instance option.

·     In a basic ACL, the source source-address source-wildcard option specifies a multicast group address.

·     In an advanced ACL, the source source-address source-wildcard option specifies a multicast source address. The destination dest-address dest-wildcard option specifies a multicast group address.

·     Among the other optional parameters, only the fragment keyword and the time-range time-range-name option take effect.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# On the public network, configure an SA creation policy to advertise only the (10.10.0.0/16, 225.1.0.0/16) entries when creating an SA message.

<Sysname> system-view

[Sysname] acl number 3101

[Sysname-acl-adv-3101] rule permit ip source 10.10.0.0 0.0.255.255 destination 225.1.0.0 0.0.255.255

[Sysname-acl-adv-3101] quit

[Sysname] msdp

[Sysname-msdp] import-source acl 3101

Related commands

peer sa-policy

msdp

Use msdp to enable MSDP and enter MSDP view.

Use undo msdp to disable MSDP and remove the configurations in MSDP view to release the resources occupied by MSDP.

Syntax

msdp [ vpn-instance vpn-instance-name ]

undo msdp [ vpn-instance vpn-instance-name ]

Default

MSDP is disabled.

Views

System view

Predefined user roles

network-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command applies to the public network.

Usage guidelines

You must enable IP multicast routing on the public network or for a VPN instance before you execute this command.

Examples

# Enable IP multicast routing and MSDP on the public network, and enter public network MSDP view.

<Sysname> system-view

[Sysname] multicast routing

[Sysname-mrib] quit

[Sysname] msdp

[Sysname-msdp]

Related commands

multicast routing

originating-rp

Use originating-rp to configure the originating RP of SA messages.

Use undo originating-rp to restore the default.

Syntax

originating-rp interface-type interface-number

undo originating-rp

Default

SA messages are originated by real RPs.

Views

MSDP view

Predefined user roles

network-admin

Parameters

interface-type interface-number: Specifies an interface by its type and number.

Examples

# On the public network, configure VLAN-interface 100 as the originating RP of SA messages.

<Sysname> system-view

[Sysname] msdp

[Sysname-msdp] originating-rp vlan-interface 100

peer

Use peer to specify an MSDP peer.

Use undo peer to remove an MSDP peer.

Syntax

peer peer-address connect-interface interface-type interface-number

undo peer peer-address

Default

MSDP peers do not exist.

Views

MSDP view

Predefined user roles

network-admin

Parameters

peer-address: Specifies an MSDP peer by its IP address.

connect-interface interface-type interface-number: Specifies an interface by its type and number. The local device uses the primary IP address of the specified interface as the source IP address when setting up a TCP connection with the remote MSDP peer.

Usage guidelines

You must execute this command before you use any other peer commands. Otherwise, the system notifies you that the MSDP peer does not exist.

Examples

# On the public network, configure the router with IP address 125.10.7.6 as the MSDP peer of the local router, and configure VLAN-interface 100 as the local connection port.

<Sysname> system-view

[Sysname] msdp

[Sysname-msdp] peer 125.10.7.6 connect-interface vlan-interface 100

peer description

Use peer description to configure the description for an MSDP peer.

Use undo peer description to delete the description for an MSDP peer.

Syntax

peer peer-address description text

undo peer peer-address description

Default

An MSDP peer is not configured with a description.

Views

MSDP view

Predefined user roles

network-admin

Parameters

peer-address: Specifies an MSDP peer by its IP address.

text: Specifies a description, a case-sensitive string of 1 to 80 characters, including spaces.

Examples

# On the public network, configure a description of CustomerA for the device at 125.10.7.6.

<Sysname> system-view

[Sysname] msdp

[Sysname-msdp] peer 125.10.7.6 description CustomerA

peer mesh-group

Use peer mesh-group to assign an MSDP peer to a mesh group.

Use undo peer mesh-group to remove an MSDP peer from a mesh group.

Syntax

peer peer-address mesh-group name

undo peer peer-address mesh-group

Default

An MSDP peer does not belong to a mesh group.

Views

MSDP view

Predefined user roles

network-admin

Parameters

peer-address: Specifies an MSDP peer by its IP address.

name: Specifies a mesh group, a case-sensitive string of 1 to 32 characters. A mesh group name must not contain any spaces.

Examples

# On the public network, assign MSDP peer 125.10.7.6 to mesh group Group1.

<Sysname> system-view

[Sysname] msdp

[Sysname-msdp] peer 125.10.7.6 mesh-group Group1

peer minimum-ttl

Use peer minimum-ttl to set the lower TTL threshold for multicast data packets encapsulated in SA messages.

Use undo peer minimum-ttl to restore the default.

Syntax

peer peer-address minimum-ttl ttl-value

undo peer peer-address minimum-ttl

Default

The lower TTL threshold for a multicast packet to be encapsulated in an SA message is 0.

Views

MSDP view

Predefined user roles

network-admin

Parameters

peer-address: Specifies an MSDP peer by its IP address.

ttl-value: Specifies the lower TTL threshold in the range of 0 to 255.

Examples

# On the public network, set the lower TTL threshold of multicast packets to be encapsulated in SA messages for MSDP peer 110.10.10.1 to 10. Only multicast data packets whose TTL values are larger than or equal to 10 can be encapsulated in SA messages and forwarded to MSDP peer 110.10.10.1.

<Sysname> system-view

[Sysname] msdp

[Sysname-msdp] peer 110.10.10.1 minimum-ttl 10

peer password

Use peer password to configure an MD5 authentication key used by both MSDP peers to establish a TCP connection.

Use undo peer password to restore the default.

Syntax

peer peer-address password { cipher | simple } password

undo peer peer-address password

Default

MSDP peers do not perform MD5 authentication to establish TCP connections.

Views

MSDP view

Predefined user roles

network-admin

Parameters

peer-address: Specifies an MSDP peer by its IP address.

cipher: Specifies a ciphertext MD5 authentication key.

simple: Specifies a plaintext MD5 authentication key.

password: Specifies a key string. This argument is case sensitive. If simple is specified, it must be a string of 1 to 80 characters. If cipher is specified, it must be a ciphertext string of 33 to 137 characters.

Usage guidelines

The MSDP peers involved in MD5 authentication must be configured with the same authentication method and key. Otherwise, the authentication fails and the TCP connection cannot be established.

For security purposes, all keys, including keys configured in plain text, are saved in cipher text.

Examples

# On the public network, configure an MD5 authentication key in plaintext as aabbcc for the TCP connections between the local end and MSDP peer 10.1.100.1.

<Sysname> system-view

[Sysname] msdp

[Sysname-msdp] peer 10.1.100.1 password simple aabbcc

peer request-sa-enable

Use peer request-sa-enable to enable the device to send an SA request message to an MSDP peer after receiving a new join message.

Use undo peer request-sa-enable to disable the device from sending an SA request message to an MSDP peer.

Syntax

peer peer-address request-sa-enable

undo peer peer-address request-sa-enable

Default

After receiving a new join message, the device does not send an SA request message to any MSDP peers. Instead, it waits for an SA message.

Views

MSDP view

Predefined user roles

network-admin

Parameters

peer-address: Specifies an MSDP peer by its IP address.

Usage guidelines

You must disable SA message cache mechanism before you execute this command. Otherwise, the device does not send out SA request messages.

Examples

# On the public network, disable the SA message cache mechanism.

<Sysname> system-view

[Sysname] msdp

[Sysname-msdp] undo cache-sa-enable

# Enable the device to send an SA request message to MSDP peer 125.10.7.6 after it receives a new join message.

[Sysname-msdp] peer 125.10.7.6 request-sa-enable

Related commands

·     cache-sa-enable

·     display msdp peer-status

peer sa-cache-maximum

Use peer sa-cache-maximum to set the maximum number of (S, G) entries in the SA cache learned from an MSDP peer.

Use undo peer sa-cache-maximum to restore the default.

Syntax

peer peer-address sa-cache-maximum sa-limit

undo peer peer-address sa-cache-maximum

Default

The device can cache a maximum of 4294967295 (S, G) entries learned from any MSDP peer.

Views

MSDP view

Predefined user roles

network-admin

Parameters

peer-address: Specifies an MSDP peer by its IP address.

sa-limit: Specifies the maximum number of (S, G) entries in the SA cache, in the range of 1 to 4294967295.

Examples

# On the public network, set the maximum number of (S, G) entries in the SA cache learned from MSDP peer 125.10.7.6 to 100.

<Sysname> system-view

[Sysname] msdp

[Sysname-msdp] peer 125.10.7.6 sa-cache-maximum 100

Related commands

·     display msdp brief

·     display msdp peer-status

·     display msdp sa-count

peer sa-policy

Use peer sa-policy to configure an SA incoming or outgoing policy.

Use undo peer sa-policy to remove the configured SA incoming or outgoing policy.

Syntax

peer peer-address sa-policy { export | import } [ acl acl-number ]

undo peer peer-address sa-policy { export | import }

Default

No SA incoming or outgoing policy exists. All SA messages are accepted or forwarded.

Views

MSDP view

Predefined user roles

network-admin

Parameters

export: Specifies the outgoing direction.

import: Specifies the incoming direction.

peer-address: Specifies an MSDP peer by its IP address.

acl-number: Specifies an IPv4 advanced ACL number in the range of 3000 to 3999. If you specify an ACL, the device accepts and forwards only SA messages that the ACL permits. The device discards all SA messages when one of the following conditions exists:

·     You do not specify an ACL.

·     The specified ACL does not exist.

·     The specified ACL does not have any valid rules.

Usage guidelines

This command controls the acceptance or forwarding of SA messages. To control the creation of SA messages, use the import-source command.

When you configure a rule in the IPv4 advanced ACL, follow these restrictions and guidelines:

·     For the rule to take effect, do not specify the vpn-instance vpn-instance option.

·     The source source-address source-wildcard option specifies a multicast source address.

·     The destination dest-address dest-wildcard option specifies a multicast group address.

·     Among the other optional parameters, only the fragment keyword and the time-range time-range-name option take effect.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# On the public network, configure an SA outgoing policy to forward only SA messages that ACL 3100 permits to MSDP peer 125.10.7.6.

<Sysname> system-view

[Sysname] acl number 3100

[Sysname-acl-adv-3100] rule permit ip source 170.15.0.0 0.0.255.255 destination 225.1.0.0 0.0.255.255

[Sysname-acl-adv-3100] quit

[Sysname] msdp

[Sysname-msdp] peer 125.10.7.6 connect-interface vlan-interface 100

[Sysname-msdp] peer 125.10.7.6 sa-policy export acl 3100

Related commands

·     display msdp peer-status

·     import-source

peer sa-request-policy

Use peer sa-request-policy to configure an SA request policy.

Use undo peer sa-request-policy to remove the configured SA request policy.

Syntax

peer peer-address sa-request-policy [ acl acl-number ]

undo peer peer-address sa-request-policy

Default

No SA request policy exists.

Views

MSDP view

Predefined user roles

network-admin

Parameters

peer-address: Specifies an MSDP peer by its IP address.

acl-number: Specifies an IPv4 basic ACL number in the range of 2000 to 2999. If you specify an ACL, the device accepts only SA requests that the ACL permits. The device discards all SA requests when one of the following conditions exists:

·     You do not specify an ACL.

·     The specified ACL does not exist.

·     The specified ACL does not have any valid rules.

Usage guidelines

When you configure a rule in the IPv4 basic ACL, follow these restrictions and guidelines:

·     For the rule to take effect, do not specify the vpn-instance vpn-instance option.

·     The source source-address source-wildcard option specifies a multicast group address.

·     Among the other optional parameters, only the fragment keyword and the time-range time-range-name option take effect.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# On the public network, configure an SA request policy to process SA requests originated from MSDP peer 175.58.6.5 with multicast groups in the range of 225.1.1.0/24.

<Sysname> system-view

[Sysname] acl number 2001

[Sysname-acl-basic-2001] rule permit source 225.1.1.0 0.0.0.255

[Sysname-acl-basic-2001] quit

[Sysname] msdp

[Sysname-msdp] peer 175.58.6.5 sa-request-policy acl 2001

reset msdp peer

Use reset msdp peer to reset the TCP connection with an MSDP peer and clear statistics for the MSDP peer.

Syntax

reset msdp [ vpn-instance vpn-instance-name ] peer [ peer-address ]

Views

User view

Predefined user roles

network-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command resets the TCP connection with the specified MSDP peer and clears statistics for the MSDP peer on the public network.

peer-address: Specifies an MSDP peer by its IP address. If you do not specify an MSDP peer, this command resets the TCP connections with all MSDP peers.

Examples

# On the public network, reset the TCP connection with MSDP peer 125.10.7.6, and clear all statistics for this MSDP peer.

<Sysname> reset msdp peer 125.10.7.6

reset msdp sa-cache

Use reset msdp sa-cache to clear (S, G) entries from the SA cache.

Syntax

reset msdp [ vpn-instance vpn-instance-name ] sa-cache [ group-address ]

Views

User view

Predefined user roles

network-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command clears (S, G) entries from the SA cache on the public network.

group-address: Specifies a multicast group by its IP address in the range of 224.0.1.0 to 239.255.255.255. If you do not specify a multicast group, this command clears the cached (S, G) entries for all multicast groups from the SA cache.

Examples

# Clear the (S, G) entries for multicast group 225.5.4.3 from the SA cache on the public network.

<Sysname> reset msdp sa-cache 225.5.4.3

Related commands

·     cache-sa-enable

·     display msdp sa-cache

reset msdp statistics

Use reset msdp statistics to clear statistics for an MSDP peer without resetting the TCP connection with the MSDP peer.

Syntax

reset msdp [ vpn-instance vpn-instance-name ] statistics [ peer-address ]

Views

User view

Predefined user roles

network-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command clears statistics for the specified MSDP peer without resetting the TCP connection with the MSDP peer on the public network.

peer-address: Specifies an MSDP peer by its IP address. If you do not specify an MSDP peer, this command clears statistics for all MSDP peers without resetting the TCP connections with all MSDP peers.

Examples

# On the public network, clear statistics for MSDP peer 125.10.7.6 without resetting the TCP connection with the peer.

<Sysname> reset msdp statistics 125.10.7.6

shutdown (MSDP view)

Use shutdown to tear down the connection with an MSDP peer.

Use undo shutdown to re-establish the connection an MSDP peer.

Syntax

shutdown peer-address

undo shutdown peer-address

Default

The connections with an MSDP peer is active.

Views

MSDP view

Predefined user roles

network-admin

Parameters

peer-address: Specifies an MSDP peer by its IP address.

Examples

# Tear down the connection with MSDP peer 125.10.7.6 on the public network.

<Sysname> system-view

[Sysname] msdp

[Sysname-msdp] shutdown 125.10.7.6

Related commands

·     display msdp brief

·     display msdp peer-status

static-rpf-peer

Use static-rpf-peer to configure a static RPF peer.

Use undo static-rpf-peer to remove a static RPF peer.

Syntax

static-rpf-peer peer-address [ rp-policy ip-prefix-name ]

undo static-rpf-peer peer-address

Default

No static RPF peers exist.

Views

MSDP view

Predefined user roles

network-admin

Parameters

peer-address: Specifies an MSDP peer by its IP address.

rp-policy ip-prefix-name: Specifies a filtering policy based on RP addresses in SA messages by its name, a case-sensitive string of 1 to 63 characters. If you specify a filtering policy, the device does not perform RPF checks on SA messages permitted by the policy. If you do not specify a filtering policy, the device performs RPF checks on all SA messages.

Usage guidelines

This command prevents SA messages forwarded by the static RPF peer from undertaking the RPF check.

Examples

# On the public network, configure IP prefix list list1 to permit SA messages originated by RPs in the range of 130.10.0.0/16.

<Sysname> system-view

[Sysname] ip prefix-list list1 permit 130.10.0.0 16 great-equal 16 less-equal 32

# On the public network, configure the interface with IP address 130.10.7.6 as the static RPF peer and reference IP prefix list list1.

[Sysname] msdp

[Sysname-msdp] peer 130.10.7.6 connect-interface vlan-interface 100

[Sysname-msdp] static-rpf-peer 130.10.7.6 rp-policy list1

Related commands

·     display msdp peer-status

·     ip prefix-list

timer retry

Use timer retry to set the MSDP connection retry interval.

Use undo timer retry to restore the default.

Syntax

timer retry interval

undo timer retry

Default

The MSDP connection retry interval is 30 seconds.

Views

MSDP view

Predefined user roles

network-admin

Parameters

interval: Specifies an MSDP connection retry interval in the range of 1 to 60 seconds.

Examples

# Set the MSDP connection retry interval to 60 seconds on the public network.

<Sysname> system-view

[Sysname] msdp

[Sysname-msdp] timer retry 60