10-H3C WA系列上行链路完整性检测配置举例
本章节下载: 10-H3C WA系列上行链路完整性检测配置举例 (117.76 KB)
H3C WA系列上行链路完整性检测配置举例
关键词:链路完整性, uplink
摘 要:在无线环境中,当AP的上行链路状态变为down时,用户即使关联到AP,也无法使用网络资源。可以通过配置上行链路完整性检查,当AP的上行链路出现故障时,用户无法关联到该AP,从而可以强迫用户关联到其它AP上去。
缩略语:
缩略语 |
英文全名 |
中文解释 |
AP |
Access Point |
接入点 |
目 录
上行链路检测功能是在AP的上行链路都出现故障时,禁止无线用户连接到该AP。
当AP的上行链路都出现故障时,AP无法连接到外部网络。若继续让无线用户连接到该AP,无线用户仍然无法访问外部网络.利用上行链路检测功能,可以在上行链路出现故障时,禁止无线用户连接到该AP。
本配置举例中的AP使用的是WA1208E-GP无线局域网接入点。
在AP的接口Ethernet1/0/1上配置上行链路完整性检测功能,接口Ethernet1/0/1关闭,AP强迫用户下线,并且用户无法搜索到该AP的SSID;接口Ethernet1/0/1打开,重新连接用户,用户可以搜索到该AP的SSID,可以连接到该AP。
图3-1 上行链路完整性检测组网图
<AP> display version
H3C Comware Platform Software
Comware Software, Version 5.00, 0001
Copyright (c) 2004-2008 Hangzhou H3C Tech. Co., Ltd. All rights reserved.
Compiled May 7 2008 18:04:56, RELEASE SOFTWARE
WA1208E-GP uptime is 0 week, 1 day, 0 hour, 13 minutes
CPU type: IXP422
64M bytes SDRAM Memory
8M bytes Flash Memory
Pcb Version: Ver.A
Basic BootROM Version: 2.01
Extend BootROM Version: 2.01
[SLOT 1]CON (Hardware)Ver.A, (Driver)1.0
[SLOT 1]ETH1/0/1 (Hardware)Ver.A, (Driver)1.0
[SLOT 1]RADIO1/0/1 (Hardware)Ver.A, (Driver)1.0
[AP]display current-confiuration
#
version 5.20, Beta 1102
#
sysname AP
#
domain default enable system
#
wlan uplink-interface Ethernet1/0/1
#
vlan 1
#
domain system
access-limit disable
state active
idle-cut disable
self-service-url disable
#
wlan rrm
dot11a mandatory-rate 6 12 24
dot11a supported-rate 9 18 36 48 54
dot11b mandatory-rate 1 2
dot11b supported-rate 5.5 11
dot11g mandatory-rate 1 2 5.5 11
dot11g supported-rate 6 9 12 18 24 36 48 54
#
wlan service-template 1 clear
ssid ChinaNet
authentication-method open-system
service-template enable
#
interface NULL0
#
interface Ethernet1/0/1
#
interface Ethernet1/0/2
#
interface WLAN-BSS1
#
interface WLAN-Radio1/0/1
#
interface WLAN-Radio1/0/2
service-template 1 interface wlan-bss 1
#
user-interface con 0
user-interface vty 0 4
#
# 进入系统视图。
<AP> system-view
# 创建一个clear类型的服务模板1。
[AP]wlan service-template 1 clear
# 设置服务模板1的SSID为ChinaNet。
[AP-wlan-st-1]ssid ChinaNet
# 使能开放式系统认证。
[AP-wlan-st-1]authentication-method open-system
# 使能服务模板1。
[AP-wlan-st-1]service-template enable
# 在系统视图下创建编号为1的WLAN-BSS接口。
[AP]interface WLAN-BSS 1
# 在无线接口WLAN-Radio 1/0/2上绑定服务模版1和接口WLAN-BSS 1。
[AP]interface WLAN-Radio 1/0/2
[AP-WLAN-Radio1/0/2]service-template 1 interface WLAN-BSS 1
[AP]wlan uplink-interface ethernet 1/0/1。
可通过以下方式验证上述配置:
按照如上步骤配置上行链路检测功能。
让用户连接到该AP。
[AP]display wlan client
Total Number of Clients : 1
Total Number of Clients Connected : 1
Client Information
--------------------------------------------------------------------------
MAC Address BSSID AID State PS Mode QoS Mode
--------------------------------------------------------------------------
0009-5b94-2f23 000f-e27b-3e74 501 Running Active None
--------------------------------------------------------------------------
关闭接口Ethernet1/0/1,可以发现AP强迫用户下线,并且用户无法搜索到该AP的SSID。
[AP]interface ethernet 1/0/1
[AP-Ethernet1/0/1]shutdown
#Apr 2 17:45:49:342 2000 H3C IFNET/4/INTERFAPE UPDOWN:
Trap 1.3.6.1.6.3.1.1.5.3<linkDown>: Interface 9371648 is Down, ifAdminStatus is
2, ifOperStatus is 2
%Apr 2 17:45:49:343 2000 H3C IFNET/4/LINK UPDOWN:
Ethernet1/0/1: link status is DOWN
[AP-Ethernet1/0/1]display wlan client
% Info: Clients do not exist.
打开接口Ethernet1/0/1,重新连接用户,用户可以搜索到该AP的SSID,可以连接到该AP。
无
《H3C WA系列无线局域网接入点设备 用户手册》“WLAN分册”中的“WLAN”。
不同款型规格的资料略有差异, 详细信息请向具体销售和400咨询。H3C保留在没有任何通知或提示的情况下对资料内容进行修改的权利!