· Only fiber-to-copper transceiver modules can be used to switch the port speed from 1000 Mbps to 100 Mbps. To configure a GE port to operate at 100 Mbps, first install a compatible fiber-to-copper transceiver module and then execute the speed 100 command.

MPUs

You can install one MPU, or two MPUs for redundancy for the router. To install two MPUs for the router, make sure they are the same model.

CSR05SRP1P1

View

Figure2-1 CSR05SRP1P1 view

(1) USB console port	(2) USB 2.0 port
(3) 10/100/1000BASE-T management Ethernet ports (port 1 reserved for future use)	(4) Console port
(5) System reset button	(6) MPU active/standby LED. For the LED description, see Table2-1.
(7) Card status LEDs. For the LED description, see Table2-2.	(8) Power supply status LEDs. For the LED description, see Table2-3.
(9) Fan tray status LEDs. For the LED description, see Table2-4.	(10) Management Ethernet port LED. For the LED description, see Table2-5.

LEDs

Table2-1 MPU active/standby LED description

LED mark	Status	Description
ACTIVE	Steady green	The MPU is in active state.
Off	· The MPU is in standby state. · The MPU is faulty. To further determine the MPU status, see the card status LED description for the MPU.

LED mark

Status

Description

ACTIVE

Steady green

The MPU is in active state.

Off

· The MPU is in standby state.

· The MPU is faulty. To further determine the MPU status, see the card status LED description for the MPU.

Table2-2 Card status LED description

LED status		Description
RUN (green)	ALM (red)	Description
Flashing green (once every 2 seconds)	Off	The card in the corresponding slot is operating correctly.
Fast flashing green (once every 4 seconds)	Steady on	The card in the corresponding slot is loading software. If the card keeps in this state, the software version of the card is not compatible with that of the device.
Flashing green (once every 2 seconds)	Flashing red (once every 4 seconds)	The temperature of the card in the corresponding slot is abnormal. The temperature has exceeded the upper warning temperature threshold or dropped below the lower temperature threshold.
Steady on	Steady on	The card in the corresponding slot is starting or faulty.
Off	Off	No card is available in the corresponding slot.

NOTE:

The ALM LED being on for a while at the system startup does not mean that the card is faulty.

Table2-3 Power supply status LED description

LED status		Description
OK (green)	FAIL (red)	Description
Steady on	Off	All power supplies in the chassis are operating correctly.
Off	Steady on	A minimum of one power supply in the chassis does not have power output. Possible reasons include: · The power supply is faulty. · The power switch for the power supply has not been turned on. · Power cord connection failure. · Power outage of the external power supply system.
Off	Off	· No power supplies are present in the chassis. · No power supply in the chassis has power output. Possible reasons include: ¡ The power supplies are faulty. ¡ The power switches for the power supplies have not been turned on. ¡ Power cord connection failure. ¡ Power outage of the external power supply system.

Table2-4 Fan tray status LED description

LED status		Description
OK (green)	FAIL (red)	Description
Steady on	Off	The fan tray is operating correctly.
Off	Steady on	One or multiple fans in the fan tray are faulty or the fan tray is installed incorrectly.
Off	Off	The router is not powered on.

Table2-5 Management Ethernet port LED description

LED mark	Status	Description
LINK/ACT	Flashing green	The port is in sending or receiving data.
	Steady green	A link is present on the port.
	Off	No link is present on the port.

Ports

Console port

The console port can be connected to a computer for system debugging, configuration, maintenance, management, and host software loading.

Table2-6 Console port specifications

Item	Description
Connector type	RJ-45
Compliant standard	Asynchronous EIA/TIA-232
Transmission baud rate	≤ 115200 bps. The default value is 9600 bps.
Transmission medium and max transmission distance	Common asynchronous serial interface cable, with a maximum transmission distance of 15 m (49.21 ft)
Services	Connects to the serial port on a local PC running a terminal emulation program.

Table2-7 USB console port specifications

Item	Description
Connector type	USB-AB
Compliant standard	USB 2.0, full speed
Transmission baud rate	≤ 115200 bps. The default value is 9600 bps.
Transmission medium and max transmission distance	USB-AB cable, with a maximum transmission distance of 2 m (6.56 ft)
Services	Connects to the USB port on a local PC running a terminal emulation program to provide a command-line interface for the router. A generic USB to serial port driver is required on the PC. Connects routers to PCs or similar terminals that do not have a serial port.

Management Ethernet port

The management Ethernet port can be connected to a computer for router program loading and router debugging, or connects to a remote NMS for remote management.

Table2-8 Management Ethernet port specifications

Item	Description
Connector type	RJ-45
Port quantity	2 (port 1 reserved for future use)
Transmission baud rate	10/100/1000 Mbps
Transmission medium and max transmission distance	Category-5 or above twisted pair cable, with a transmission distance of 100 m (328.08 ft)
Services	For router software upgrade and network management

USB port

USB ports can connect multiple types of devices and provide a higher data transfer rate than common parallel interfaces and serial interfaces.

Table2-9 USB port specifications

Item	Description
Connector type	USB A
Compliant standard	USB 2.0
Services	External storage media

NOTE:

The USB port does not support an extension cable.

Technical specifications

Table2-10 Technical specifications

Item	Description
Dimensions (H × W × D)	52.2 × 399 × 352 mm (2.06 × 15.71 × 13.86 in)
Weight	4.30 kg (9.48 lb)
Maximum power consumption	64 W
Typical power consumption	60 W
Minimum power consumption	58 W
Operating temperature	0°C to 45°C (32°F to 113°F)
SDRAM	8 GB

CSR05SRP1P3-G

View

Figure2-2 CSR05SRP1P3-G view

(1) High-precision time synchronization ports (Both are input ports by default. When both ports are input ports, only port 1 is valid.)	(2) SMB coaxial clock ports (2 input ports and 2 output ports)
(3) USB console port	(4) USB 2.0 port
(5) 1000BASE-T management Ethernet ports	(6) Console port
(7) System reset button	(8) MPU active/standby LED. For the LED description, see Table2-11.
(9) Card status LEDs. For the LED description, see Table2-12.	(10) Power supply status LED. For the LED description, see Table2-13.
(11) Fan tray status LED. For the LED description, see Table2-14.	(12) Management Ethernet port LED. For the LED description, see Table2-15.

LEDs

Table2-11 MPU active/standby LED description

LED mark	Status	Description
ACTIVE	Steady green	The MPU is in active state.
Off	· The MPU is in standby state. · The MPU is faulty. To further determine the MPU status, see the card status LED description for the MPU.

LED mark

Status

Description

ACTIVE

Steady green

The MPU is in active state.

Off

· The MPU is in standby state.

· The MPU is faulty. To further determine the MPU status, see the card status LED description for the MPU.

Table2-12 Card status LED description

LED status	Description
Flashing green	The card in the corresponding slot is operating correctly.
Flashing green (4 Hz)	The card in the corresponding slot is loading software. If the card keeps in this state, the software version of the card is not compatible with that of the device.
Steady red	The card in the corresponding slot is starting or faulty.
Flashing red	The temperature of the card in the corresponding slot is abnormal. The temperature has exceeded the upper warning temperature threshold or dropped below the lower temperature threshold.
Off	No card is available in the corresponding slot.

Table2-13 Power supply status LED description

LED mark	Status	Description
PWR (red or green)	Green	All power supplies in the chassis are operating correctly.
	Steady red	A minimum of one power supply in the chassis does not have power output. Possible reasons include: · The power supply is faulty. · The power switch for the power supply has not been turned on. · Power cord connection failure. · Power outage of the external power supply system.
	Off	· No power supplies are present in the chassis. · No power supply in the chassis has power output. Possible reasons include: ¡ The power supplies are faulty. ¡ The power switches for the power supplies have not been turned on. ¡ Power cord connection failure. ¡ Power outage of the external power supply system.

Table2-14 Fan tray status LED description

LED mark	Status	Description
FAN	Steady green	The fan tray is operating correctly.
	Steady red	One or multiple fans in the fan tray are faulty or the fan tray is installed incorrectly.
	Off	The router is not powered on.

Table2-15 Management Ethernet port LED description

LED mark	Status	Description
LINK/ACT	Flashing green	The port is in sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Ports

Console port

The console port can be connected to a computer for system debugging, configuration, maintenance, management, and host software loading.

Table2-16 Console port specifications

Item	Description
Connector type	RJ-45
Compliant standard	Asynchronous EIA/TIA-232
Transmission baud rate	≤ 115200 bps. The default value is 9600 bps.
Transmission medium and max transmission distance	Common asynchronous serial interface cable, with a maximum transmission distance of 15 m (49.21 ft)
Services	Connects to the serial port on a local PC running a terminal emulation program.

Table2-17 USB console port specifications

Item	Description
Connector type	USB-AB
Compliant standard	USB 2.0, full speed
Transmission baud rate	≤ 115200 bps. The default value is 9600 bps.
Transmission medium and max transmission distance	USB-AB cable, with a maximum transmission distance of 2 m (6.56 ft)
Services	Connects to the USB port on a local PC running a terminal emulation program to provide a command-line interface for the router. A generic USB to serial port driver is required on the PC. Connects routers to PCs or similar terminals that do not have a serial port.

Management Ethernet port

The management Ethernet port can be connected to a computer for router program loading and router debugging, or connects to a remote NMS for remote management.

Table2-18 Management Ethernet port specifications

Item	Description
Connector type	RJ-45
Port quantity	2
Transmission baud rate	1000 Mbps, full duplex
Transmission medium and max transmission distance	Category-5 or above twisted pair cable, with a transmission distance of 100 m (328.08 ft)
Services	For router software upgrade and network management

USB port

USB ports can connect multiple types of devices and provide a higher data transfer rate than common parallel interfaces and serial interfaces.

Table2-19 USB port specifications

Item	Description
Connector type	USB A
Compliant standard	USB 2.0
Services	External storage media

NOTE:

The USB port does not support an extension cable.

SMB coaxial clock input/output port

SMB coaxial clock ports provide input or output clock references at 2.048 Mbps (2.048 MHz). You can set the data rate mode or frequency mode through CLI. Two of them are input ports and two are output ports.

Table2-20 SMB coaxial clock input/output port specifications

Item	Description
Connector type	SMB coaxial
Compliant standard	GJB681
Transmission baud rate	2.048 Mbps
Transmission medium	75 ohm coaxial cable
Services	Sends and receives 2.048 MHz clocks and 2.048 Mbps signals to synchronize the clocks of the router and other devices, such as routers and the terminals.

Table2-21 High-precision time synchronization port specifications

Item	Description
Connector type	RJ-45
Compliant standard	QB-B-016-2010
Transmission baud rate	9600 bps
Transmission medium	Category-5 or above twisted pair cable
Services	You can configure the port as an input port or output port at the CLI. Synchronizes the clocks of the router and other devices, such as GPS receivers and terminals.

Technical specifications

Table2-22 Technical specifications

Item	Description
Dimensions (H × W × D)	52.2 × 399 × 352 mm (2.06 × 15.71 × 13.86 in)
Weight	4.50 kg (9.92 lb)
Maximum power consumption	65 W
Typical power consumption	50 W
Minimum power consumption	40 W
Operating temperature	0°C to 45°C (32°F to 113°F)
SDRAM	16 GB

CSR05SRP1R3

View

Figure2-3 CSR05SRP1R3 view

(1) High-precision time synchronization ports (Both are input ports by default. When both ports are input ports, only port 1 is valid.)	(2) SMB coaxial clock ports (2 input ports and 2 output ports)
(3) USB console port	(4) USB 2.0 port
(5) 1000BASE-T Management Ethernet ports (port 1 reserved for future use)	(6) Console port
(7) System reset button	(8) MPU active/standby LED. For the LED description, see Table2-23.
(9) Card status LEDs. For the LED description, see Table2-24.	(10) Power supply status LEDs. For the LED description, see Table2-25.
(11) Fan tray status LEDs. For the LED description, see Table2-26.	(12) Management Ethernet port LED. For the LED description, see Table2-27.

LEDs

Table2-23 MPU active/standby LED description

LED mark	Status	Description
ACTIVE	Steady green	The MPU is in active state.
Off	· The MPU is in standby state. · The MPU is faulty. To further determine the MPU status, see the card status LED description for the MPU.

LED mark

Status

Description

ACTIVE

Steady green

The MPU is in active state.

Off

· The MPU is in standby state.

· The MPU is faulty. To further determine the MPU status, see the card status LED description for the MPU.

Table2-24 Card status LED description

LED status		Description
RUN (green)	ALM (red)	Description
Flashing green (once every 2 seconds)	Off	The card in the corresponding slot is operating correctly.
Fast flashing green (once every 4 seconds)	Steady on	The card in the corresponding slot is loading software. If the card keeps in this state, the software version of the card is not compatible with that of the device.
Flashing green (once every 2 seconds)	Flashing red (once every 4 seconds)	The temperature of the card in the corresponding slot is abnormal. The temperature has exceeded the upper warning temperature threshold or dropped below the lower temperature threshold.
Steady on	Steady on	The card in the corresponding slot is starting or faulty.
Off	Off	No card is available in the corresponding slot.

NOTE:

The ALM LED being on for a while at the system startup does not mean that the card is faulty.

Table2-25 Power supply status LED description

LED status		Description
OK (green)	FAIL (red)	Description
Steady on	Off	All power supplies in the chassis are operating correctly.
Off	Steady on	A minimum of one power supply in the chassis does not have power output. Possible reasons include: · The power supply is faulty. · The power switch for the power supply has not been turned on. · Power cord connection failure. · Power outage of the external power supply system.
Off	Off	· No power supplies are present in the chassis. · No power supply in the chassis has power output. Possible reasons include: ¡ The power supplies are faulty. ¡ The power switches for the power supplies have not been turned on. ¡ Power cord connection failure. ¡ Power outage of the external power supply system.

Table2-26 Fan tray status LED description

LED status		Description
OK (green)	FAIL (red)	Description
Steady on	Off	The fan tray is operating correctly.
Off	Steady on	One or multiple fans in the fan tray are faulty or the fan tray is installed incorrectly.
Off	Off	The router is not powered on.

Table2-27 Management Ethernet port LED description

LED mark	LED	Description
LINK/ACT	Flashing green	The port is in sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Ports

Console port

The console port can be connected to a computer for system debugging, configuration, maintenance, management, and host software loading.

Table2-28 Console port specifications

Item	Description
Connector type	RJ-45
Compliant standard	Asynchronous EIA/TIA-232
Transmission baud rate	≤ 115200 bps. The default value is 9600 bps.
Transmission medium and max transmission distance	Common asynchronous serial interface cable, with a maximum transmission distance of 15 m (49.21 ft)
Services	Connects to the serial port on a local PC running a terminal emulation program.

Table2-29 USB console port specifications

Item	Description
Connector type	USB-AB
Compliant standard	USB 2.0, full speed
Transmission baud rate	≤ 115200 bps. The default value is 9600 bps.
Transmission medium and max transmission distance	USB-AB cable, with a maximum transmission distance of 2 m (6.56 ft)
Services	Connects to the USB port on a local PC running a terminal emulation program to provide a command-line interface for the router. A generic USB to serial port driver is required on the PC. Connects routers to PCs or similar terminals that do not have a serial port.

Management Ethernet port

The management Ethernet port can be connected to a computer for router program loading and router debugging, or connects to a remote NMS for remote management.

Table2-30 Management Ethernet port specifications

Item	Description
Connector type	RJ-45
Port quantity	2 (port 1 reserved for future use)
Transmission baud rate	1000 Mbps, full duplex
Transmission medium and max transmission distance	Category-5 or above twisted pair cable, with a transmission distance of 100 m (328.08 ft)
Services	For router software upgrade and network management

USB port

USB ports can connect multiple types of devices and provide a higher data transfer rate than common parallel interfaces and serial interfaces.

Table2-31 USB port specifications

Item	Description
Connector type	USB A
Compliant standard	USB 2.0
Services	External storage media

NOTE:

The USB port does not support an extension cable.

SMB coaxial clock input/output port

Table2-32 SMB coaxial clock input/output port specifications

Item	Description
Connector type	SMB coaxial
Compliant standard	GJB681
Transmission baud rate	2.048 Mbps
Transmission medium	75 ohm coaxial cable
Services	Sends and receives 2.048 MHz clocks and 2.048 Mbps signals to synchronize the clocks of the router and other devices, such as routers and the terminals.

Table2-33 High-precision time synchronization port specifications

Item	Description
Connector type	RJ-45
Compliant standard	QB-B-016-2010
Transmission baud rate	9600 bps
Transmission medium	Category-5 or above twisted pair cable
Services	You can configure the port as an input port or output port at the CLI. Synchronizes the clocks of the router and other devices, such as GPS receivers and terminals.

Technical specifications

Table2-34 Technical specifications

Item	Description
Dimensions (H × W × D)	52.2 × 399 × 352 mm (2.06 × 15.71 × 13.86 in)
Weight	4.90 kg (10.80 lb)
Maximum power consumption	130 W
Typical power consumption	95 W
Minimum power consumption	89 W
Operating temperature	0°C to 45°C (32°F to 113°F)
SDRAM	2 × 16 GB

CSR05SRP1R3-G

View

Figure2-4 CSR05SRP1R3-G view

(1) High-precision time synchronization ports (Both are input ports by default. When both ports are input ports, only port 1 is valid.)	(2) SMB coaxial clock output ports (2 in total)
(3) SMB coaxial clock input ports (2 in total)	(4) USB 2.0 port
(5) 1000BASE-T management Ethernet ports	(6) Console port
(7) System reset button	(8) MPU active/standby LED. For the LED description, see Table2-35.
(9) Card status LEDs. For the LED description, see Table2-36.	(10) Power supply status LED. For the LED description, see Table2-37.
(11) Fan tray status LED. For the LED description, see Table2-38.	(12) Management Ethernet port LED. For the LED description, see Table2-39.

LEDs

Table2-35 MPU active/standby LED description

LED mark	Status	Description
ACTIVE	Steady green	The MPU is in active state.
Off	· The MPU is in standby state. · The MPU is faulty. To further determine the MPU status, see the card status LED description for the MPU.

LED mark

Status

Description

ACTIVE

Steady green

The MPU is in active state.

Off

· The MPU is in standby state.

· The MPU is faulty. To further determine the MPU status, see the card status LED description for the MPU.

Table2-36 Card status LED description

LED status	Description
Flashing green	The card in the corresponding slot is operating correctly.
Fast flashing green (4 Hz)	The card in the corresponding slot is loading software. If the card keeps in this state, the current software version of the device is not running the software version compatible with the card.
Steady red	The card in the corresponding slot is starting or faulty.
Flashing red	The temperature of the card in the corresponding slot is abnormal. The temperature has exceeded the upper warning temperature threshold or dropped below the lower temperature threshold.
Off	No card is available in the corresponding slot.

Table2-37 Power supply status LED description

Power supply status LED	Status	Description
PWR (red or green)	Steady green	All power supplies in the chassis are operating correctly.
	Steady red	A minimum of one power supply in the chassis does not have power output. Possible reasons include: · The power supply is faulty. · The power switch for the power supply has not been turned on. · Power cord connection failure. Power outage of the external power supply system.
	Off	· No power supplies are present in the chassis. · No power supply in the chassis has power output. Possible reasons include: ¡ The power supplies are faulty. ¡ The power switches for the power supplies have not been turned on. ¡ Power cord connection failure. ¡ Power outage of the external power supply system.

Table2-38 Fan tray status LED description

Fan tray status LED	Status	Description
FAN (Red or green)	Steady green	The fan tray is operating correctly.
	Steady red	One or more fans in the fan tray have failed or the fan tray is installed incorrectly.
	Off	The router is not powered on.

Table2-39 Management Ethernet port LED description

LED mark	Status	Description
LINK/ACT	Flashing green	The port is in sending or receiving data.
	Steady green	A link is present on the port.
	Off	No link is present on the port.

Ports

Console port

The console port can be connected to a computer for system debugging, configuration, maintenance, management, and host software loading.

Table2-40 Console port specifications

Item	Description
Connector type	RJ-45
Compliant standard	Asynchronous EIA/TIA-232
Transmission baud rate	≤ 115200 bps. The default value is 9600 bps.
Transmission medium and max transmission distance	Common asynchronous serial interface cable, with a maximum transmission distance of 15 m (49.21 ft)
Services	Connects to the serial port on a local PC running a terminal emulation program.

Management Ethernet port

The management Ethernet port can be connected to a computer for router program loading and router debugging, or connects to a remote NMS for remote management.

Table2-41 Management Ethernet port specifications

Item	Description
Connector type	RJ-45
Port quantity	2
Transmission baud rate	1000 Mbps, full duplex
Transmission medium and max transmission distance	Category-5 or above twisted pair cable, with a transmission distance of 100 m (328.08 ft)
Services	For router software upgrade and network management

USB port

USB ports can connect multiple types of devices and provide a higher data transfer rate than common parallel interfaces and serial interfaces.

Table2-42 USB port specifications

Item	Description
Connector type	USB A
Compliant standard	USB 2.0
Services	External storage media

NOTE:

The USB port does not support an extension cable.

SMB coaxial clock input/output port

SMB coaxial clock ports provide input or output clock references at 2.048 Mbps (2.048 MHz). You can set the data rate mode or frequency mode through the CLI. Two of them are input ports and two are output ports.

Table2-43 SMB coaxial clock input/output port specifications

Item	Description
Connector type	SMB coaxial
Compliant standard	GJB681
Transmission baud rate	2.048 Mbps
Transmission medium	75-ohm coaxial cable
Services	Sends and receives 2.048 MHz clocks and 2.048 Mbps signals to synchronize the clocks of the router and other devices, such as routers and the terminals.

High-precision time synchronization port

Table2-44 High-precision time synchronization port specifications

Item	Description
Connector type	RJ-45
Compliant standard	QB-B-016-2010
Transmission baud rate	9600 bps
Transmission medium	Category-5 or above twisted pair cable
Services	You can configure the port as an input port or output port at the CLI. Synchronizes the clocks of the router and other devices, such as GPS receivers and terminals.

Technical specifications

Table2-45 Technical specifications

Item	Description
Dimensions (H × W × D)	52.2 × 399 × 352 mm (2.06 × 15.71 × 13.86 in)
Weight	4.55 kg (10.03 lb)
Maximum power consumption	130 W
Typical power consumption	117 W
Minimum power consumption	55 W
Operating temperature	0°C to 45°C (32°F to 113°F)
SDRAM	16 GB or 32 GB (subject to the card specifications)

SR05SRP1L1

View

Figure2-5 SR05SRP1L1 view

(1) CF card	(2) Console port
(3) USB console port	(4) 10/100/1000BASE-T Management Ethernet port
(5) USB 2.0 port	(6) System reset button
(7) MPU active/standby LED. For the LED description, see Table2-46.	(8) Card status LEDs. For the LED description, see Table2-47.
(9) Fan tray status LEDs. For the LED description, see Table2-48.	(10) Management Ethernet port LEDs. For the LED description, see Table2-49.
(11) CF card LED. For the LED description, see Table2-50.

LEDs

Table2-46 MPU active/standby LED description

LED mark

LED

Description

ACTIVE

Steady green

The MPU is in active state.

Off

· The MPU is in standby state.

· The MPU is faulty. To further determine the MPU status, see the card status LED description for the MPU.

Table2-47 Card status LED description

LED status		Description
RUN (green)	ALM (red)	Description
Flashing green (once every 2 seconds)	Off	The card in the corresponding slot is operating correctly.
Fast flashing green (once every 4 seconds)	Steady on	The card in the corresponding slot is loading software. If the card keeps in this state, the software version of the card is not compatible with that of the card.
Flashing green (once every 2 seconds)	Flashing red (once every 4 seconds)	The temperature of the card in the corresponding slot is abnormal. The temperature has exceeded the upper warning temperature threshold or dropped below the lower temperature threshold.
Steady on	Steady on	The card in the corresponding slot is starting or faulty.
Off	Off	No card is available in the corresponding slot.

NOTE:

The ALM LED being on for a while at the system startup does not mean that the card is faulty.

Table2-48 Fan tray status LED description

LED status		Description
OK (green)	FAIL (red)	Description
Steady on	Off	The fan tray is operating correctly.
Off	Steady on	One or multiple fans in the fan tray are faulty or the fan tray is installed incorrectly.
Off	Off	The router is not powered on.

Table2-49 Management Ethernet port LED description

Status		Description
LINK (green)	ACT (yellow)	Description
Steady on	Flashing green	The port is in sending or receiving data.
Steady on	Off	A link is present on the port.
Off	Off	No link is present on the port.

Table2-50 CF card LED description

LED	Status	Description
CF card (green)	Steady on	The CF card is present and idle. Do not hot swap it.
	Flashing green	The CF card is present and the system is reading/writing the card. Do not hot swap it.
	Off	The CF card is not present, or the CF card is in offline state. You can hot swap it.

Ports

Console port

The console port can be connected to a computer for system debugging, configuration, maintenance, management, and host software loading.

Table2-51 Console port specifications

Item	Description
Connector type	RJ-45
Compliant standard	Asynchronous EIA/TIA-232
Transmission baud rate	≤ 115200 bps. The default value is 9600 bps.
Transmission medium and max transmission distance	Common asynchronous serial interface cable, with a maximum transmission distance of 15 m (49.21 ft)
Services	Connects to the serial port on a local PC running a terminal emulation program.

Table2-52 USB console port specifications

Item	Description
Connector type	USB-AB
Compliant standard	USB 2.0, full speed
Transmission baud rate	≤ 115200 bps. The default value is 9600 bps.
Transmission medium and max transmission distance	USB-AB cable, with a maximum transmission distance of 2 m (6.56 ft)
Services	Connects to the USB port on a local PC running a terminal emulation program to provide a command-line interface for the router. A generic USB to serial port driver is required on the PC. Connects routers to PCs or similar terminals that do not have a serial port.

Management Ethernet port

The management Ethernet port can be connected to a computer for router program loading and router debugging, or connects to a remote NMS for remote management.

Table2-53 Management Ethernet port specifications

Item	Description
Connector type	RJ-45
Port quantity	1
Transmission baud rate	10/100/1000 Mbps
Transmission medium and max transmission distance	Category-5 or above twisted pair cable, with a transmission distance of 100 m (328.08 ft)
Services	For router software upgrade and network management

USB port

USB ports can connect multiple types of devices and provide a higher data transfer rate than common parallel interfaces and serial interfaces.

Table2-54 USB port specifications

Item	Description
Connector type	USB A
Compliant standard	USB 2.0
Services	External storage media

NOTE:

The USB port does not support an extension cable.

CF card slot

A CF card is a mobile storage device that features fast speed, large capacity, small size, light weight, and low power consumption.

Table2-55 External CF card specifications

Item	Description
CF card slots	1
CF card capacity	4 GB
Services	You can use a CF card to store logs, application program files, and configuration files.

NOTE:

Before you use a CF card, insert the CF card into the card slot and fasten the card cover.

Technical specifications

Table2-56 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.05 kg (6.72 lb)
Maximum power consumption	53 W
Typical power consumption	47 W
Minimum power consumption	46 W
Operating temperature	0°C to 45°C (32°F to 113°F)
SDRAM	8 GB or 16 GB (subject to the card specifications)

SR05SRP1L3

View

Figure2-6 SR05SRP1L3 view

(1) High-precision time synchronization ports (Both are input ports by default. When both ports are input ports, only port 1 is valid.)	(2) CF card
(3) SMB coaxial clock ports (2 input ports and 2 output ports)	(4) Console port
(5) USB console port	(6) 10/100/1000BASE-T management Ethernet port
(7) USB 2.0 port	(8) System reset button
(9) MPU active/standby LED. For the LED description, see Table2-57.	(10) Card status LEDs. For the LED description, see Table2-58.
(11) Fan tray status LEDs. For the LED description, see Table2-59.	(12) Management Ethernet port LEDs. For the LED description, see Table2-60.
(13) Card status LED. For the LED description, see Table2-61.

LEDs

Table2-57 MPU active/standby LED description

LED mark

LED

Description

ACTIVE

Steady green

The MPU is in active state.

Off

· The MPU is in standby state.

· The MPU is faulty. To further determine the MPU status, see the card status LED description for the MPU.

Table2-58 Card status LED description

LED status		Description
RUN (green)	ALM (red)	Description
Flashing green (once every 2 seconds)	Off	The card in the corresponding slot is operating correctly.
Fast flashing green (once every 4 seconds)	Steady on	The card in the corresponding slot is loading software. If the card keeps in this state, the software version of the card is not compatible with that of the device.
Flashing green (once every 2 seconds)	Flashing red (once every 4 seconds)	The temperature of the card in the corresponding slot is abnormal. The temperature has exceeded the upper warning temperature threshold or dropped below the lower temperature threshold.
Steady on	Steady on	The card in the corresponding slot is starting or faulty.
Off	Off	No card is available in the corresponding slot.

NOTE:

The ALM LED being on for a while at the system startup does not mean that the card is faulty.

Table2-59 Fan tray status LED description

LED status		Description
OK (green)	FAIL (red)	Description
Steady on	Off	The fan tray is operating correctly.
Off	Steady on	One or multiple fans in the fan tray are faulty or the fan tray is installed incorrectly.
Off	Off	The router is not powered on.

Table2-60 Management Ethernet port LED description

Status		Description
LINK (green)	ACT (yellow)	Description
Steady on	Flashing green	The port is in sending or receiving data.
Steady on	Off	A link is present on the port.
Off	Off	No link is present on the port.

Table2-61 CF card LED description

LED	Status	Description
CF card (green)	Steady on	The CF card is present and idle. Do not hot swap it.
	Flashing green	The CF card is present and the system is reading/writing the card. Do not hot swap it.
	Off	The CF card is not present, or the CF card is in offline state. You can hot swap it.

Ports

Console port

The console port can be connected to a computer for system debugging, configuration, maintenance, management, and host software loading.

Table2-62 Console port specifications

Item	Description
Connector type	RJ-45
Compliant standard	Asynchronous EIA/TIA-232
Transmission baud rate	≤ 115200 bps. The default value is 9600 bps.
Transmission medium and max transmission distance	Common asynchronous serial interface cable, with a maximum transmission distance of 15 m (49.21 ft)
Services	Connects to the serial port on a local PC running a terminal emulation program.

Table2-63 USB console port specifications

Item	Description
Connector type	USB-AB
Compliant standard	USB 2.0, full speed
Transmission baud rate	≤ 115200 bps. The default value is 9600 bps.
Transmission medium and max transmission distance	USB-AB cable, with a maximum transmission distance of 2 m (6.56 ft)
Services	Connects to the USB port on a local PC running a terminal emulation program to provide a command-line interface for the router. A generic USB to serial port driver is required on the PC. Connects routers to PCs or similar terminals that do not have a serial port.

Management Ethernet port

The management Ethernet port can be connected to a computer for router program loading and router debugging, or connects to a remote NMS for remote management.

Table2-64 Management Ethernet port specifications

Item	Description
Connector type	RJ-45
Port quantity	1
Transmission baud rate	10/100/1000 Mbps
Transmission medium and max transmission distance	Category-5 or above twisted pair cable, with a transmission distance of 100 m (328.08 ft)
Services	For router software upgrade and network management

USB port

USB ports can connect multiple types of devices and provide a higher data transfer rate than common parallel interfaces and serial interfaces.

Table2-65 USB port specifications

Item	Description
Connector type	USB A
Compliant standard	USB 2.0
Services	External storage media

NOTE:

The USB port does not support an extension cable.

CF card slot

A CF card is a mobile storage device that features fast speed, large capacity, small size, light weight, and low power consumption.

Table2-66 External CF card specifications

Item	Description
CF card slots	1
CF card capacity	4 GB
Services	You can use a CF card to store logs, application program files, and configuration files.

NOTE:

Before you use a CF card, insert the CF card into the card slot and fasten the card cover.

SMB coaxial clock input/output port

Table2-67 SMB coaxial clock input/output port specifications

Item	Description
Connector type	SMB coaxial
Compliant standard	GJB681
Transmission baud rate	2.048Mbps
Transmission medium	75 ohm coaxial cable
Services	Sends and receives 2.048 MHz clocks and 2.048 Mbps signals to synchronize the clocks of the router and other devices, such as routers and the terminals.

Table2-68 High-precision time synchronization port specifications

Item	Description
Connector type	RJ-45
Compliant standard	QB-B-016-2010
Transmission baud rate	9600 bps
Transmission medium	Category-5 or above twisted pair cable
Services	You can configure the port as an input port or output port at the CLI. Synchronizes the clocks of the router and other devices, such as GPS receivers and terminals.

Technical specifications

Table2-69 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.18 kg (7.01 lb)
Maximum power consumption	53 W
Typical power consumption	52 W
Minimum power consumption	50 W
Operating temperature	0°C to 45°C (32°F to 113°F)
SDRAM	8 GB or 16 GB (subject to the card specifications)

SR05SRP1P3

View

Figure2-7 SR05SRP1P3 view

(1) High-precision time synchronization ports (Both are input ports by default. When both ports are input ports, only port 1 is valid.)	(2) CF card
(3) USB console port	(4) SMB coaxial clock ports (2 input ports and 2 output ports)
(5) USB 2.0 port	(6) 10/100/1000BASE-T management Ethernet ports (port 1 reserved for future use)
(7) Console port	(8) System reset button
(9) MPU active/standby LED. For the LED description, see Table2-70.	(10) Card status LEDs. For the LED description, see Table2-71.
(11) Power supply status LEDs. For the LED description, see Table2-72.	(12) Fan tray status LEDs. For the LED description, see Table2-73.
(13) Management Ethernet port LED. For the LED description, see Table2-74.	(14) CF card LED. For the LED description, see Table2-75.

LED

Table2-70 MPU active/standby LED description

LED mark

LED

Description

ACTIVE

Steady green

The MPU is in active state.

Off

· The MPU is in standby state.

· The MPU is faulty. To further determine the MPU status, see the card status LED description for the MPU.

Table2-71 Card status LED description

LED status		Description
RUN (green)	ALM (red)	Description
Flashing green (once every 2 seconds)	Off	The card in the corresponding slot is operating correctly.
Fast flashing green (once every 4 seconds)	Steady on	The card in the corresponding slot is loading software. If the card keeps in this state, the software version of the card is not compatible with that of the card.
Flashing green (once every 2 seconds)	Flashing red (once every 4 seconds)	The temperature of the card in the corresponding slot is abnormal. The temperature has exceeded the upper warning temperature threshold or dropped below the lower temperature threshold.
Steady on	Steady on	The card in the corresponding slot is starting or faulty.
Off	Off	No card is available in the corresponding slot.

NOTE:

The ALM LED being on for a while at the system startup does not mean that the card is faulty.

Table2-72 Power supply status LED description

LED status		Description
OK (green)	FAIL (red)	Description
Steady on	Off	All power supplies in the chassis are operating correctly.
Off	Steady on	A power supply in the chassis does not have power output. Possible reasons include: · The power supply is faulty. · The power switch for the power supply has not been turned on. · Power cord connection failure. · Power outage of the external power supply system.
Off	Off	· No power supplies are present in the chassis. · No power supply in the chassis has power output. Possible reasons include: ¡ The power supplies are faulty. ¡ The power switches for the power supplies have not been turned on. ¡ Power cord connection failure. ¡ Power outage of the external power supply system.

Table2-73 Fan tray status LED description

LED status		Description
OK (green)	FAIL (red)	Description
Steady on	Off	The fan tray is operating correctly.
Off	Steady on	One or multiple fans in the fan tray are faulty or the fan tray is installed incorrectly.
Off	Off	The router is not powered on.

Table2-74 Management Ethernet port LED description

LED mark	LED	Description
LINK/ACT	Flashing green	The port is in sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Table2-75 CF card LED description

LED	Status	Description
CF card (green)	Steady on	The CF card is present and idle. Do not hot swap it.
	Flashing green	The CF card is present and the system is reading/writing the card. Do not hot swap it.
	Off	The CF card is not present, or the CF card is in offline state. You can hot swap it.

Ports

Console port

The console port can be connected to a computer for system debugging, configuration, maintenance, management, and host software loading.

Table2-76 Console port specifications

Item	Description
Connector type	RJ-45
Compliant standard	Asynchronous EIA/TIA-232
Transmission baud rate	≤ 115200 bps. The default value is 9600 bps.
Transmission medium and max transmission distance	Common asynchronous serial interface cable, with a maximum transmission distance of 15 m (49.21 ft)
Services	Connects to the serial port on a local PC running a terminal emulation program.

Table2-77 USB console port specifications

Item	Description
Connector type	USB-AB
Compliant standard	USB 2.0, full speed
Transmission baud rate	≤ 115200 bps. The default value is 9600 bps.
Transmission medium and max transmission distance	USB-AB cable, with a maximum transmission distance of 2 m (6.56 ft)
Services	Connects to the USB port on a local PC running a terminal emulation program to provide a command-line interface for the router. A generic USB to serial port driver is required on the PC. Connects routers to PCs or similar terminals that do not have a serial port.

Management Ethernet port

The management Ethernet port can be connected to a computer for router program loading and router debugging, or connects to a remote NMS for remote management.

Table2-78 Management Ethernet port specifications

Item	Description
Connector type	RJ-45
Port quantity	2 (port 1 reserved for future use)
Transmission baud rate	10/100/1000 Mbps
Transmission medium and max transmission distance	Category-5 or above twisted pair cable, with a transmission distance of 100 m (328.08 ft)
Services	For router software upgrade and network management

USB port

USB ports can connect multiple types of devices and provide a higher data transfer rate than common parallel interfaces and serial interfaces.

Table2-79 USB port specifications

Item	Description
Connector type	USB A
Compliant standard	USB 2.0
Services	External storage media

NOTE:

The USB port does not support an extension cable.

CF card slot

A CF card is a mobile storage device that features fast speed, large capacity, small size, light weight, and low power consumption.

Table2-80 External CF card specifications

Item	Description
CF card slots	1
CF card capacity	4 GB
Services	You can use a CF card to store logs, application program files, and configuration files.

NOTE:

Before you use a CF card, insert the CF card into the card slot and fasten the card cover.

SMB coaxial clock input/output port

Table2-81 SMB coaxial clock input/output port specifications

Item	Description
Connector type	SMB coaxial
Compliant standard	GJB681
Transmission baud rate	2.048Mbps
Transmission medium	75 ohm coaxial cable
Services	Sends and receives 2.048 MHz clocks and 2.048 Mbps signals to synchronize the clocks of the router and other devices, such as routers and the terminals.

Table2-82 High-precision time synchronization port specifications

Item	Description
Connector type	RJ-45
Compliant standard	QB-B-016-2010
Transmission baud rate	9600 bps
Transmission medium	Category-5 or above twisted pair cable
Services	You can configure the port as an input port or output port at the CLI. Synchronizes the clocks of the router and other devices, such as GPS receivers and terminals.

Technical specifications

Table2-83 Technical specifications

Item	Description
Dimensions (H × W × D)	52.2 × 399 × 352 mm (2.06 × 15.71 × 13.86 in)
Weight	4.80 kg (10.58 lb)
Maximum power consumption	64 W
Typical power consumption	60 W
Minimum power consumption	58 W
Operating temperature	0°C to 45°C (32°F to 113°F)
SDRAM	16 GB

Compatibility information

Table2-84 Compatibility matrix between MPUs and routers

Card model	Applicable router models
SR05SRP1L1	SR8804-X, SR8808-X, SR8812-X
SR05SRP1L3	SR8804-X, SR8808-X, SR8812-X
CSR05SRP1P1	SR8808H-X, SR8816-X
SR05SRP1P3	SR8808H-X, SR8816-X
CSR05SRP1P3-G	SR8808H-X, SR8816-X
CSR05SRP1R3	SR8808H-X, SR8816-X
CSR05SRP1R3-G	SR8808H-X, SR8816-X

SPC/CSPC LPUs (interface modules)

A combo interface is a logical interface that contains an SFP port and an RJ-45 Ethernet port. Only one of them can be activated at a time.

CSPC-GE16XP4L-E

View

Figure2-8 CSPC-GE16XP4L-E view

(1) 10GBASE-R-SFP+ fiber ports (4 in total) (10GE SFP+ modules supported)	(2) Combo interfaces (16 in total) (10GE SFP+ modules supported in 1000BASE-X-SFP fiber ports)
(3) SFP port LED. For the LED description, see Table2-86.	(4) RJ-45 Ethernet Interface LED. For the LED description, see Table2-85.
(5) SFP+ port LED. For the LED description, see Table2-87.

LEDs

Table2-85 RJ-45 Ethernet port LED description

LED	Status	Description
RJ-45 Ethernet port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Table2-86 SFP port LED description

LED	Status	Description
SFP port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Table2-87 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 1000 Mbps.

Ports

Table2-88 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
CSPC-GE16XP4L-E	16-port GE combo interface + 4-port 10GE optical interface module	RJ-45	16	10/100/1000 Mbps
		LC	16	1000 Mbps
		LC	4	10 Gbps

Technical specifications

Table2-89 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	4.35 kg (9.59 lb)
Maximum power consumption	127 W
Typical power consumption	114 W
Minimum power consumption	107 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CSPC-GE24L-E

View

Figure2-9 CSPC-GE24L-E view

(1) Combo interfaces (24 in total) (10GE SFP+ modules supported in 1000BASE-X-SFP fiber ports)	(2) SFP port LED. For the LED description, see Table2-91.
(3) RJ-45 Ethernet Interface LED. For the LED description, see Table2-90.

LEDs

Table2-90 RJ-45 Ethernet port LED description

LED	Status	Description
RJ-45 Ethernet port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Table2-91 SFP port LED description

LED	Status	Description
SFP port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Ports

Table2-92 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
CSPC-GE24L-E	24-port GE Combo interface service module	RJ-45	24	10/100/1000 Mbps
CSPC-GE24L-E	24-port GE Combo interface service module	LC	24	1000 Mbps

Technical specifications

Table2-93 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	4.45 kg (9.81 lb)
Maximum power consumption	114 W
Typical power consumption	110 W
Minimum power consumption	108 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CSPC-GP24GE8XP2L-E

View

Figure2-10 CSPC-GP24GE8XP2L-E view

(1) 10GBASE-R-SFP+ fiber ports (2 in total) (10GE SFP+ modules supported)	(2) 1000BASE-X-SFP fiber ports (24 in total) (GE SFP modules supported)
(3) Combo interfaces (8 in total) (10GE SFP+ modules supported in 1000BASE-X-SFP fiber ports)	(4) RJ-45 Ethernet Interface LED. For the LED description, see Table2-94.
(5) SFP port LED. For the LED description, see Table2-95.	(6) SFP+ port LED. For the LED description, see Table2-96.

LEDs

Table2-94 RJ-45 Ethernet port LED description

LED	Status	Description
RJ-45 Ethernet port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Table2-95 SFP port LED description

LED	Status	Description
SFP port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Table2-96 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 1000 Mbps.

Ports

Table2-97 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
CSPC-GP24GE8XP2L-E	24-port 1000BASE-X Ethernet optical interface (SFP, LC) + 8-port 1000BASE-X Ethernet combo interface + 2-port 10GBASE-R/W Ethernet optical interface line processing unit (SFP+, LC) (E Type)	RJ45	8	10/100/1000 Mbps
		LC	32	1000 Mbps
		LC	2	10 Gbps

Technical specifications

Table2-98 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	4.45 kg (9.81 lb)
Maximum power consumption	126 W
Typical power consumption	113 W
Minimum power consumption	101 W
Operating temperature	0°C to 45°C (32°F to 113°F)

SPC-CP1LAX/SPC-CP1LCX

View

Figure2-11 SPC-CP1LCX view

(1) 100GBASE-R-CFP fiber port (1 in total)	(2) CFP port LED. For the LED description, see Table2-99.

The views of the SPC-CP1LAX and SPC-CP1LCX are similar. This figure uses the SPC-CP1LCX as an example.

LEDs

Table2-99 CFP port LED description

LED	Status	Description
CFP port LED	Flashing	The CFP port is sending or receiving data.
	Steady on	A link is present on the CFP port.
	Off	No link is present on the CFP port.

Ports

Table2-100 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
SPC-CP1LAX	1-port 100GBASE Ethernet optical interface module (CFP, LC) (A Type)	LC	1	100 Gbps
SPC-CP1LCX	1-port 100GBASE Ethernet optical interface module (CFP, LC) (C Type)	LC	1	100 Gbps

Technical specifications

Table2-101 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.50 kg (7.72 lb)
Maximum power consumption	173 W
Typical power consumption	156 W
Minimum power consumption	115 W
Operating temperature	0°C to 45°C (32°F to 113°F)

SPC-CP2LA/SPC-CP2LB

View

Figure2-12 SPC-CP2LA view

(1) 100GBASE-R-CFP fiber ports (2 in total)	(2) CFP port LED. For the LED description, see Table2-102.

The views of the SPC-CP2LA and SPC-CP2LB are similar. This figure uses the SPC-CP2LA as an example.

LEDs

Table2-102 CFP port LED description

LED	Status	Description
CFP port LED	Flashing	The CFP port is sending or receiving data.
	Steady on	A link is present on the CFP port.
	Off	No link is present on the CFP port.

Ports

Table2-103 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
SPC-CP2LA	2-port 100GBASE Ethernet optical interface module (CFP, LC) (A Type)	LC	2	100 Gbps
SPC-CP2LB	2-port 100GBASE Ethernet optical interface module (CFP, LC) (B Type)	LC	2	100 Gbps

Technical specifications

Table2-104 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	4.06 kg (8.96 lb)
Maximum power consumption	197 W
Typical power consumption	178 W
Minimum power consumption	150 W
Operating temperature	0°C to 45°C (32°F to 113°F)

SPC-GP24LA1

View

Figure2-13 SPC-GP24LA1 view

(1) 1000BASE-X-SFP fiber ports (16 in total)	(2) Combo interfaces (8 in total)
(3) SFP port LED. For the LED description, see Table2-106.	(4) RJ-45 Ethernet port LED. For the LED description, see Table2-105.

NOTE:

· A combo interface is a logical interface that contains an SFP fiber port and an RJ-45 copper port. The two ports share one forwarding channel. As a result, they cannot work simultaneously. When you activate one port, the other port is automatically disabled. You can activate the fiber or copper port as needed. By default, the copper port is activated.

· Use a category 5 or above twisted pair cable to connect a 1000BASE-T RJ-45 copper port. The maximum transmission distance is 100 m (328.08 ft).

LEDs

Table2-105 RJ-45 Ethernet port LED description

LED	Status	Description
RJ-45 Ethernet port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Table2-106 SFP port LED description

LED	Status	Description
SFP port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Ports

Table2-107 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
SPC-GP24LA1	16-port 1000BASE-X Ethernet optical interface (SFP, LC) + 8-port combo interface module (A Type)	RJ45	8	10/100/1000 Mbps
		LC	24	100 Mbps
				155 Mbps
				1000 Mbps

Technical specifications

Table2-108 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.01 kg (6.64 lb)
Maximum power consumption	75 W
Typical power consumption	68 W
Minimum power consumption	47 W
Operating temperature	0°C to 45°C (32°F to 113°F)

SPC-GP24XP2LA/SPC-GP24XP2LB

Views

Figure2-14 SPC-GP24XP2LB view

(1) 1000BASE-X-SFP fiber ports (16 in total)	(2) Combo interfaces (8 in total)
(3) 10GBASE-R-XFP fiber ports (2 in total)	(4) SFP port LED. For the LED description, see Table2-110.
(5) RJ-45 Ethernet port LED. For the LED description, see Table2-109.	(6) XFP port LED. For the LED description, see Table2-111.

The views of the SPC-GP24XP2LA and SPC-GP24XP2LB are similar. This figure uses the SPC-GP24XP2LB as an example.

LEDs

Table2-109 RJ-45 Ethernet port LED description

LED	Status	Description
RJ-45 Ethernet port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Table2-110 SFP port LED description

LED	Status	Description
SFP port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Table2-111 XFP port LED description

XFP port LED status		Description
LINK	ACT	Description
Steady on	Flashing green	A link is present, and the XFP port is sending or receiving data.
Steady on	Off	A link is present, but the XFP port is not sending or receiving data.
Off	Off	No link is present on the XFP port.

Ports

Table2-112 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
SPC-GP24XP2LA	16-port 1000BASE-X Ethernet optical interface (SFP, LC) + 8-port combo interface + 2-port 10GE optical interface module (XFP, LC) (A Type)	RJ45	8	10/100/1000 Mbps
		LC	24	100 Mbps
				155 Mbps
				1000 Mbps
		LC	2	10 Gbps
SPC-GP24XP2LB	16-port 1000BASE-X optical interface (SFP, LC) + 8-port combo interface + 2-port 10GE optical interface module (XFP, LC) (B Type)	RJ45	8	10/100/1000 Mbps
		LC	24	100 Mbps
				155 Mbps
				1000 Mbps
		LC	2	10 Gbps

Technical specifications

Table2-113 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.08 kg (6.79 lb)
Maximum power consumption	100 W
Typical power consumption	90 W
Minimum power consumption	51 W
Operating temperature	0°C to 45°C (32°F to 113°F)

SPC-GP44XP4LAX/SPC-GP44XP4LCX

View

Figure2-15 SPC-GP44XP4LCX view

(1) 1000BASE-X-SFP fiber ports (44 in total)	(2) 10GBASE-R-SFP+ fiber ports (4 in total)
(3) SFP port LED. For the LED description, see Table2-114.	(4) SFP+ port LED. For the LED description, see Table2-115.

The views of the SPC-GP44XP4LAX and SPC-GP44XP4LCX are similar. This figure uses the SPC-GP44XP4LCX as an example.

LEDs

Table2-114 SFP port LED description

LED	Status	Description
SFP port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Table2-115 SFP+ port LED description

LED	Status	Description
SFP+ port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 1000 Mbps.

Ports

Table2-116 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
SPC-GP44XP4LAX	44-port 1000BASE-X Ethernet optical interface module (SFP, LC) + 4-port 10GBASE Ethernet optical interface module (SFP+, LC) (A Type)	LC	44	100 Mbps
				155 Mbps
				1000 Mbps
			4	10 Gbps
			4	1000 Mbps
SPC-GP44XP4LCX	44-port 1000BASE-X Ethernet optical interface module (SFP, LC) + 4-port 10GBASE Ethernet optical interface module (SFP+, LC) (C Type)	LC	44	100 Mbps
				155 Mbps
				1000 Mbps
			4	10 Gbps
			4	1000 Mbps

Technical specifications

Table2-117 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.60 kg (7.94 lb)
Maximum power consumption	142 W
Typical power consumption	128 W
Minimum power consumption	118 W
Operating temperature	0°C to 45°C (32°F to 113°F)

SPC-GP48LA1/SPC-GP48LB

View

Figure2-16 SPC-GP48LA1 view

(1) 1000BASE-X-SFP fiber ports (48 in total)	(2) SFP port LED. For the LED description, see Table2-118.

The views of the SPC-GP48LB and SPC-GP48LA1 are similar. This figure uses the SPC-GP48LA1 as an example.

LEDs

Table2-118 SFP port LED description

LED	Status	Description
SFP port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Ports

Table2-119 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
SPC-GP48LA1	48-port 1000BASE-X Ethernet optical interface module (SFP, LC) (A Type)	LC	48	100 Mbps
				155 Mbps
				1000 Mbps
SPC-GP48LB	48-port enhanced 1000BASE-X Ethernet optical interface module (SFP, LC) (B Type)	LC	48	100 Mbps
				155 Mbps
				1000 Mbps

Technical specifications

Table2-120 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.25 kg (7.17 lb)
Maximum power consumption	110 W
Typical power consumption	99 W
Minimum power consumption	43 W
Operating temperature	0°C to 45°C (32°F to 113°F)

SPC-GT48LA1

View

Figure2-17 SPC-GT48LA1 view

(1) 10/100/1000BASE-T copper ports (48 in total)	(2) RJ-45 Ethernet port LED. For the LED description, see Table2-121.

LEDs

Table2-121 RJ-45 Ethernet port LED description

LED	Status	Description
RJ-45 Ethernet port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Ports

Table2-122 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
SPC-GT48LA1	48-port 10/100/1000BASE-T Ethernet interface module (RJ45) (A Type)	RJ45	48	10/100/1000 Mbps

Technical specifications

Table2-123 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.31 kg (7.30 lb)
Maximum power consumption	95 W
Typical power consumption	86 W
Minimum power consumption	67 W
Operating temperature	0°C to 45°C (32°F to 113°F)

SPC-XLP6LAX/SPC-XLP6LCX

View

Figure2-18 SPC-XLP6LCX view

(1) 40GBASE-R-QSFP+ fiber ports (6 in total)	(2) QSFP+ port LED. For the LED description, see Table2-124.

The views of the SPC-XLP6LAX and SPC-XLP6LCX are similar. This figure uses the SPC-XLP6LCX as an example.

LEDs

Table2-124 QSFP + port LED description

LED	Status	Description
QSFP + port LED	Flashing	The QSFP+ port is sending or receiving data.
	Steady on	A link is present on the QSFP+ port.
	Off	No link is present on the QSFP+ port.

Ports

Table2-125 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
SPC-XLP6LAX	6-port 40GBASE Ethernet optical interface module (QSFP+, MPO) (A Type)	LC/MPO	6	40 Gbps
SPC-XLP6LCX	6-port 40GBASE Ethernet optical interface module (QSFP+, MPO) (C Type)	LC/MPO	6	40 Gbps

Technical specifications

Table2-126 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.95 kg (8.71 lb)
Maximum power consumption	290 W
Typical power consumption	261 W
Minimum power consumption	181 W
Operating temperature	0°C to 45°C (32°F to 113°F)

SPC-XP12LAX/SPC-XP12LCX

View

Figure2-19 SPC-XP12LCX view

(1) 10GBASE-R-SFP+ fiber ports (12 in total)	(2) SFP+ port LED. For the LED description, see Table2-127.

The views of the SPC-XP12LAX and SPC-XP12LCX are similar. This figure uses the SPC-XP12LCX as an example.

LEDs

Table2-127 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 1000 Mbps.

Ports

Table2-128 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
CSPC-XP12LAX	12-port 10GE optical interface module	LC	12	10 Gbps
CSPC-XP12LAX	12-port 10GE optical interface module	LC	12	1000 Mbps
CSPC-XP12LCX	12-port 10GE optical interface module	LC	12	10 Gbps
CSPC-XP12LCX	12-port 10GE optical interface module	LC	12	1000 Mbps

Technical specifications

Table2-129 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.65 kg (8.05 lb)
Maximum power consumption	· SPC-XP12LAX: 130 W · SPC-XP12LCX: 173 W
Typical power consumption	· SPC-XP12LAX: 117 W · SPC-XP12LCX: 156 W
Minimum power consumption	· SPC-XP12LAX: 107 W · SPC-XP12LCX: 122 W
Operating temperature	0°C to 45°C (32°F to 113°F)

SPC-XP24LAX/SPC-XP24LCX

View

Figure2-20 SPC-XP24LCX view

(1) 10GBASE-R-SFP+ fiber ports (24 in total)	(2) SFP+ port LED. For the LED description, see Table2-130.

The views of the SPC-XP24LAX and SPC-XP24LCX are similar. This figure uses the SPC-XP24LCX as an example.

LEDs

Table2-130 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 1000 Mbps.

Ports

Table2-131 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
SPC-XP24LAX	24-port 10GBASE Ethernet optical interface module (SFP+, LC) (A Type)	LC	24	10 Gbps
SPC-XP24LAX		LC	24	1000 Mbps
SPC-XP24LCX	4-port 10GBASE Ethernet optical interface module (SFP+, LC) (C Type)	LC	24	10 Gbps
SPC-XP24LCX		LC	24	1000 Mbps

Technical specifications

Table2-132 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	4.15 kg (9.15 lb)
Maximum power consumption	· SPC-XP24LAX: 209 W · SPC-XP24LCX: 294 W
Typical power consumption	· SPC-XP24LAX: 189 W · SPC-XP24LCX: 265 W
Minimum power consumption	· SPC-XP24LAX: 153 W · SPC-XP24LCX: 178 W
Operating temperature	0°C to 45°C (32°F to 113°F)

SPC-XP2LA1

View

Figure2-21 SPC-XP2LA1 view

(1) 10GBASE-R-XFP fiber ports (2 in total)	(2) XFP port LED. For the LED description, see Table2-133.

LEDs

Table2-133 XFP port LED description

XFP port LED status		Description
LINK	ACT	Description
Steady on	Flashing green	A link is present, and the XFP port is sending or receiving data.
Steady on	Off	A link is present, but the XFP port is not sending or receiving data.
Off	Off	No link is present on the XFP port.

Ports

Table2-134 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
SPC-XP2LA1	2-port 10GBASE Ethernet optical interface module (XFP, LC) (A Type)	LC	2	10 Gbps

Technical specifications

Table2-135 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in))
Weight	2.93 kg (6.46 lb)
Maximum power consumption	55 W
Typical power consumption	50 W
Minimum power consumption	43 W
Operating temperature	0°C to 45°C (32°F to 113°F)

SPC-XP4LA1/SPC-XP4LB

View

Figure2-22 SPC-XP4LA1 view

(1) 10GBASE-R-XFP fiber ports (2 in total)	(2) XFP port LED. For the LED description, see Table2-136.

The views of the SPC-XP4LB and SPC-XP4LA1 are similar. This figure uses the SPC-XP4LA1 as an example.

LEDs

Table2-136 XFP port LED description

XFP port LED status		Description
LINK	ACT	Description
Steady on	Flashing green	A link is present, and the XFP port is sending or receiving data.
Steady on	Off	A link is present, but the XFP port is not sending or receiving data.
Off	Off	No link is present on the XFP port.

Ports

Table2-137 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
SPC-XP4LA1	4-port 10GBASE Ethernet optical interface module (XFP, LC) (A Type)	LC	4	10 Gbps
SPC-XP4LB	4-port Enhanced 10GBASE Ethernet optical interface module (XFP, LC) (B Type)	LC	4	10 Gbps

Technical specifications

Table2-138 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	2.93 kg (6.46 lb)
Maximum power consumption	80 W
Typical power consumption	72 W
Minimum power consumption	53 W
Operating temperature	0°C to 45°C (32°F to 113°F)

SPC-XP8LA/SPC-XP8LB

View

Figure2-23 SPC-XP8LA view

(1) 10GBASE-R-SFP+ fiber ports (8 in total)	(2) SFP+ port LED. For the LED description, see Table2-139.

The views of the SPC-XP8LB and SPC-XP8LA are similar. This figure uses the SPC-XP8LA as an example.

LED

Table2-139 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 1000 Mbps.

Ports

Table2-140 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
SPC-XP8LA	8-port 10GBASE Ethernet optical interface module (SFP+, LC) (A Type)	LC	8	100 Mbps
				1000 Mbps
				10 Gbps
SPC-XP8LB	8-port Enhanced 10GBASE Ethernet optical interface module (SFP+, LC) (B Type)	LC	8	10 Gbps
SPC-XP8LB		LC	8	1000 Mbps

Technical specifications

Table2-141 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.44 kg (7.58 lb)
Maximum power consumption	170 W
Typical power consumption	153 W
Minimum power consumption	117 W
Operating temperature	0°C to 45°C (32°F to 113°F)

Compatibility information

Table2-142 Compatibility matrix between SPC/CSPC cards and routers

Card model	SR8804-X, SR8808-X, SR8812-X	SR8808H-X, SR8816-X
SPC-GT48LA1	Supported	Not supported
CSPC-GE24L-E	Supported	Not supported
SPC-GP24LA1	Supported	Not supported
SPC-GP24XP2LA	Supported	Not supported
SPC-GP24XP2LB	Supported	Not supported
CSPC-GP24GE8XP2L-E	Supported	Not supported
CSPC-GE16XP4L-E	Supported	Not supported
SPC-XP2LA1	Supported	Not supported
SPC-XP4LA1	Supported	Not supported
SPC-XP4LB	Supported	Not supported
SPC-XP8LA	Supported	Not supported
SPC-XP8LB	Supported	Not supported
SPC-GP48LA1	Supported	Not supported
SPC-GP48LB	Supported	Not supported
SPC-GP44XP4LCX	Supported	Not supported
SPC-GP44XP4LAX	Supported	Not supported
SPC-XP24LCX	Supported	Not supported
SPC-XP24LAX	Supported	Not supported
SPC-XP12LCX	Supported	Not supported
SPC-XP12LAX	Supported	Not supported
SPC-XLP6LCX	Supported	Not supported
SPC-XLP6LAX	Supported	Not supported
SPC-CP1LCX	Supported	Not supported
SPC-CP1LAX	Supported	Not supported
SPC-CP2LB	Supported	Not supported
SPC-CP2LA	Supported	Not supported

CEPC LPUs (interface modules)

CEPC-CP4RX

View

Figure2-24 CEPC-CP4RX view

(1) 100GBASE-R-CFP2 fiber ports (4 in total)	(2) CFP2 port LED. For the LED description, see Table2-143.

LEDs

Table2-143 CFP2 port LED description

LED	Status	Description
CFP2 port LED	Flashing	The CFP2 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the CFP2 port.
	Off	No link is present on the CFP2 port.

Ports

Table2-144 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
CEPC-CP4RX	4-port 100GBASE Ethernet optical interface module (CFP2)	LC	4	100 Gbps

Technical specifications

Table2-145 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	4.20 kg (9.26 lb)
Maximum power consumption	368 W
Typical power consumption	331 W
Minimum power consumption	228.5 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CEPC-CP4RX-L

Views

Figure2-25 CEPC-CP4RX-L view

(1) 100GBASE-QSFP28 fiber ports (4 in total) (100G QSFP 28 modules supported)	(2) QSFP 28 port LED. For the LED description, see Table2-146.

LEDs

Table2-146 QSFP28 port LED description

LED	Status	Description
QSFP28 port LED	Flashing	The QSFP28 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the QSFP28 port.
	Off	No link is present on the QSFP28 port.

Ports

Table2-147 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
CEPC-CP4RX-L	4-port 100G Ethernet optical interface line processing unit (QSFP28, LC)	LC	4	100 Gbps
CEPC-CP4RX-L		LC	4	40 Gbps

Technical specifications

Table2-148 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	8.30 kg (18.30 lb)
Maximum power consumption	354 W
Typical power consumption	252 W
Minimum power consumption	191 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CEPC-CQ16L1

View

Figure2-26 CEPC-CQ16L1 view

(1) 100GBASE-QSFP28 fiber ports (16 in total)	(2) QSFP 28 port LED. For the LED description, see Table2-149.

LEDs

Table2-149 QSFP28 port LED description

LED	Status	Description
QSFP28 port LED	Flashing	The QSFP28 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the QSFP28 port.
	Off	No link is present on the QSFP28 port.

Ports

IMPORTANT:

Only ports 1, 2, 7, 8, 9, 10, 15, and 16 support switching the speed between 100 Gbps and 40 Gbps.

Table2-150 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
CEPC-CQ16L1	16-port 100G Ethernet optical interface line processing unit (QSFP28,LC)	LC	16	100 Gbps
CEPC-CQ16L1		LC	16	40 Gbps

Technical specifications

Table2-151 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 mm × 399 mm × 370 mm (2.07 in × 15.71 in × 14.57 in)
Weight	8.25 kg (18.19 lb)
Maximum power consumption	1240 W
Typical power consumption	970 W
Minimum power consumption	760 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CEPC-CQ8L

View

Figure2-27 CEPC-CQ8L view

(1) 100GBASE-QSFP28 fiber ports (8 in total) (100G QSFP 28 modules supported)	(2) QSFP 28 port LED. For the LED description, see Table2-152.

LEDs

Table2-152 QSFP28 port LED description

LED	Status	Description
QSFP28 port LED	Flashing	The QSFP28 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the QSFP28 port.
	Off	No link is present on the QSFP28 port.

Ports

Table2-153 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
CEPC-CQ8L	8-port 100G Ethernet optical interface line processing unit (QSFP28, LC)	LC	8	100 Gbps

Technical specifications

Table2-154 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 mm × 399 mm × 370 mm (2.07 in × 15.71 in × 14.57 in)
Weight	8.00 kg (17.64 lb)
Maximum power consumption	CEPC-CQ8L: 1100 W
Typical power consumption	CEPC-CQ8L: 880 W
Minimum power consumption	CEPC-CQ8L: 653 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CEPC-DQ2L1-G

View

Figure2-28 CEPC-DQ2L1-G view

(1) QSFP-DD port LED. For the LED description, see Table2-155.	(2) 400GBASE-R-QSFP-DD fiber ports (2 in total) (400G QSFP-DD transceiver modules supported)
(3) Card status LED. For the LED description, see Table2-156.

LEDs

Table2-155 QSFP-DD port LED description

LED	Status	Description
QSFP-DD port LED	Flashing	The QSFP-DD port is sending or receiving data.
	On	A link is present on the QSFP-DD port.
	Off	No link is present on the QSFP-DD port.

Table2-156 Card status LED description

LED	Status	Description
RUN (Green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing (about eight times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Ports

Table2-157 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
CEPC-DQ2L1-G	2-port 400G Ethernet optical interface line processing unit (QSFP-DD,LC)	LC	2	400 Gbps

Technical specifications

Table2-158 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 × 399 × 370 mm (2.07 × 15.71 × 14.57 in)
Weight	6.96 kg (15.34 lb)
Maximum power consumption	540 W
Typical power consumption	510 W
Minimum power consumption	450 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CEPC-XP24LX

View

Figure2-29 CEPC-XP24LX view

(1) 10GBASE-R/W-SFP+ fiber ports (24 in total) (10GE SFP+ modules supported)	(2) SFP+ port LED. For the LED description, see Table2-159.

LEDs

Table2-159 SFP+ port LED description

LED	Status	Description
SFP+ port LED	Flashing	The SFP+ port is sending or receiving data.
	Steady on	A link is present on the SFP+ port.
	Off	No link is present on the SFP+ port.

Ports

Table2-160 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
CEPC-XP24LX	24-port 10GBASE-R/W Ethernet optical interface line processing unit (SFP+, LC)	LC	24	10 Gbps

Technical specifications

Table2-161 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	4.70 kg (10.36 lb)
Maximum power consumption	321 W
Typical power consumption	289 W
Minimum power consumption	237.6 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CEPC-XP48RX

View

Figure2-30 CEPC-XP48RX view

(1) 10GBASE-R-SFP+ fiber ports (48 in total)	(2) SFP+ port LED. For the LED description, see Table2-162.

LEDs

Table2-162 SFP+ port LED description

LED	Status	Description
SFP+ port LED	Flashing	The SFP+ port is sending or receiving data.
	Steady on	A link is present on the SFP+ port.
	Off	No link is present on the SFP+ port.

Ports

Table2-163 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
CEPC-XP48RX	48-port 10GBASE-R/W Ethernet optical interface module (SFP+, LC)	LC	48	10 Gbps

Technical specifications

Table2-164 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	4.75 kg (10.47 lb)
Maximum power consumption	407 W
Typical power consumption	336 W
Minimum power consumption	234.8 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CEPC-XP4LX

View

Figure2-31 CEPC-XP4LX view

(1) 10GBASE-R/W-SFP+ fiber ports (4 in total) (10GE SFP+ modules supported)	(2) SFP+ port LED. For the LED description, see Table2-165.

LEDs

Table2-165 SFP+ port LED description

LED	Status	Description
SFP+ port LED	Flashing	The SFP+ port is sending or receiving data.
	Steady on	A link is present on the SFP+ port.
	Off	No link is present on the SFP+ port.

Ports

Table2-166 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
CEPC-XP4LX	4-port 10GBASE-R/W Ethernet optical interface line processing unit module (SFP+, LC)	LC	4	10 Gbps

Technical specifications

Table2-167 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	4.90 kg (10.80 lb)
Maximum power consumption	184 W
Typical power consumption	117 W
Minimum power consumption	102 W
Operating temperature	0°C to 45°C (32°F to 113°F)

Configuration restrictions and guidelines

For adequate ventilation and cooling, you can install the CEPC-CP4RX, CEPC-XP48RX, and CEPC-XP24LX cards in the following slots only when the other slots are not available.

· SR8808-X router—Slots 0, 8 and 9.

· SR8812-X router—Slots 0 and 13.

Compatibility information

Table2-168 Compatibility matrix between CEPC cards and routers

Card model	SR8804-X	SR8808-X, SR8812-X	SR8808H-X, SR8816-X
CEPC-CP4RX	Not supported	Supported	Supported
CEPC-CP4RX-L	Not supported	Supported	Supported
CEPC-XP48RX	Not supported	Supported	Supported
CEPC-XP24LX	Not supported	Supported	Supported
CEPC-XP4LX	Supported	Supported	Supported
CEPC-CQ8L	Not supported	Not supported	Supported
CEPC-CQ16L1	Not supported	Not supported	Supported
CEPC-DQ2L1-G	Not supported	Not supported	Supported

SPEX/CSPEX base cards

SPEX-1204/CSPEX-1104-E/CSPEX-1304X/CSPEX-1404X/CSPEX-1504X

IMPORTANT:

A CSPEX-1104-E card supports a maximum of three MIC-XP4L1 and MIC-GP4L subcards in total.

View

Figure2-32 SPEX-1204 view

(1) Card status LED. For the LED description, see Table2-169.

The views of SPEX-1204, CSPEX-1304X, CSPEX-1404X, CSPEX-1504X, CSPEX-1504XA, and CSPEX-1104-E are similar. This figure uses the SPEX-1204 as an example.

LEDs

Table2-169 LED description

LED	Status	Description
RUN (green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing (about eight times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Subcard slots

Table2-170 Subcard slots

Card model	Number of subcard slots
CSPEX-1104-E	4
SPEX-1204	4
CSPEX-1304X	4
CSPEX-1404X	4
CSPEX-1504X	4

Technical specifications

Table2-171 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	· CSPEX-1104-E: 3.45 kg (7.61 lb) · SPEX-1204: 3.50 kg (7.72 lb) · CSPEX-1304X: 3.75 kg (8.27 lb) · CSPEX-1404X: 7.20 kg (15.87 lb) · CSPEX-1504X: 7.20 kg (15.87 lb)
Maximum power consumption	· CSPEX-1104-E: 164 W · SPEX-1204: 190 W · CSPEX-1304X: 184 W · CSPEX-1404X: 230 W · CSPEX-1504X: 261 W
Typical power consumption	· CSPEX-1104-E: 88 W · SPEX-1204: 104 W · CSPEX-1304X: 101 W · CSPEX-1404X: 138 W · CSPEX-1504X: 154 W
Minimum power consumption	· CSPEX-1104-E: 79 W · SPEX-1204: 88 W · CSPEX-1304X: 90 W · CSPEX-1404X: 111.6 W · CSPEX-1504X: 112.1 W
Operating temperature	· 0°C to 45°C (32°F to 113°F)

CSPEX-1502X/CSPEX-1602X

View

Figure2-33 CSPEX-1602X view

(1) Card status LED. For the LED description, see Table2-172.

The views of the CSPEX-1602X and CSPEX-1502X are similar. This figure uses the CSPEX-1602X as an example.

LEDs

Table2-172 LED description

LED	Status	Description
RUN (green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing (about eight times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Subcard slots

Table2-173 Subcard slots

Card model	Number of subcard slots
CSPEX-1502X	2
CSPEX-1602X	2

Technical specifications

Table2-174 Technical specifications

Item	Description
Dimensions (H × W × D)	· 40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	· CSPEX-1502X: 3.95 kg (8.71 lb) · CSPEX-1602X: 7.50 kg (16.53 lb)
Maximum power consumption	· CSPEX-1502X: 270 W · CSPEX-1602X: 354 W
Typical power consumption	· CSPEX-1502X: 135 W · CSPEX-1602X: 222 W
Minimum power consumption	· CSPEX-1502X: 120 W · CSPEX-1602X: 174.6 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CSPEX-1512X/CSPEX-1612X/CSPEX-1812X/CSPEX-1812X-E/CSPEX-1802X/CSPEX-1802XB/CSPEX-2612X-E

View

Figure2-34 CSPEX-1512X view

(1) Card status LED. For the LED description, see Table2-175.

The views of the CSPEX-1512X, CSPEX-1612X, CSPEX-1812X, CSPEX-1812X-E, CSPEX-1802X, CSPEX-1802XB, and CSPEX-2612X-E are similar. This figure uses the CSPEX-1512X as an example.

LEDs

Table2-175 LED description

LED	Status	Description
RUN (green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing (about eight times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Subcard slots

Table2-176 Subcard slots

Card model	Number of subcard slots
CSPEX-1512X	2
CSPEX-1612X	2
CSPEX-1812X	2
CSPEX-1812X-E	2
CSPEX-1802X	2
CSPEX-1802XB	2
CSPEX-2612X-E	2

Technical specifications

Table2-177 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 mm × 399 mm × 352 mm (2.07 in × 15.71 in × 13.86 in)
Weight	· CSPEX-1512X: 5.40 kg (11.90 lb) · CSPEX-1612X: 8.75 kg (19.29 lb) · CSPEX-1812X: 5.95 kg (13.12 lb) · CSPEX-1812X-E, CSPEX-1802X, CSPEX-1802XB: 9.00 kg (19.84 lb) · CSPEX-2612X-E: 6.00 kg (13.23 lb)
Maximum power consumption	· CSPEX-1512X: 281 W · CSPEX-1612X: 320 W · CSPEX-1812X: 657 W · CSPEX-1812X-E, CSPEX-1802X, CSPEX-1802XB: 486 W · CSPEX-2612X-E: 538 W
Typical power consumption	· CSPEX-1512X: 202 W · CSPEX-1612X: 238 W · CSPEX-1812X: 426 W · CSPEX-1812X-E, CSPEX-1802X, CSPEX-1802XB: 333 W · CSPEX-2612X-E: 457 W
Minimum power consumption	· CSPEX-1512X: 185 W · CSPEX-1612X: 200 W · CSPEX-1812X: 413 W · CSPEX-1812X-E, CSPEX-1802X, CSPEX-1802XB: 275 W · CSPEX-2612X-E: 330 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CSPEX-1804X

View

Figure2-35 CSPEX-1804X view

(1) Card status LED. For the LED description, see Table2-178.

LEDs

Table2-178 LED description

LED	Status	Description
RUN (green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing (about eight times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Subcard slots

Table2-179 Subcard slots

Card model	Number of subcard slots
CSPEX-1804X	4

Technical specifications

Table2-180 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 mm × 399 mm × 352 mm (2.07 in × 15.71 in × 13.86 in)
Weight	6.30 kg (13.89 lb)
Maximum power consumption	625 W
Typical power consumption	510
Minimum power consumption	460 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CSPEX-2304X-G

View

Figure2-36 CSPEX-2304X-G view

(1) Card status LED. For the LED description, see Table2-181.

LEDs

Table2-181 LED description

LED	Status	Description
RUN (green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing (about eight times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Subcard slots

Table2-182 Subcard slots

Card model	Number of subcard slots
CSPEX-2304X-G	4

Technical specifications

Table2-183 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	4.65 kg (10.25 lb)
Maximum power consumption	280 W
Typical power consumption	242 W
Minimum power consumption	200 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CSPEX-2304X-G2

View

Figure2-37 CSPEX-2304X-G2 view

(1) Card status LED. For the LED description, see Table2-184.

LEDs

Table2-184 LED description

LED	Status	Description
RUN (Green)	Steady on	The card is faulty.
	Off	The card is faulty or is not in position.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing (about eight times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Subcard slots

Table2-185 Subcard slots

Card model	Number of subcard slots
CSPEX-2304X-G2	4

Technical specifications

Table2-186 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.80 kg (8.38 lb)
Maximum power consumption	261 W
Power consumption (with typical configuration)	154 W
Minimum power consumption	112 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CSPEX-2304X-LG

View

Figure2-38 CSPEX-2304X-LG view

(1) Card status LED. For the LED description, see Table2-187.

LEDs

Table2-187 LED description

LED	Status	Description
RUN (Green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing (about eight times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Subcard slots

Table2-188 Subcard slots

Card model	Number of subcard slots
CSPEX-2304X-LG	4

Technical specifications

Table2-189 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	4.65 kg (10.25 lb)
Maximum power consumption	280 W
Typical power consumption	242 W
Minimum power consumption	200 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CSPEX-2314X-G

View

Figure2-39 CSPEX-2314X-G view

(1) Card status LED. For the LED description, see Table2-190.

LEDs

Table2-190 LED description

LED	Status	Description
RUN (Green)	Steady on	The card is faulty.
	Off	The card is faulty or is not in position.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing (about eight times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Subcard slots

Table2-191 CSPEX-2314X-G subcard slots

Card model	Number of subcard slots
CSPEX-2314X-G	4

Technical specifications

Table2-192 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 × 399 × 352 mm (2.07 × 15.71 × 13.86 in)
Weight	11.57 kg (25.51 lb)
Maximum power consumption	385 W
Power consumption (with typical configuration)	333 W
Minimum power consumption	185 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CSPEX-2314X-G1

View

Figure2-40 CSPEX-2314X-G1 view

(1) Card status LED. For the LED description, see Table2-193.

LEDs

Table2-193 LED description

LED	Status	Description
RUN (Green)	Steady on	The card is faulty.
	Off	The card is faulty or is not in position.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing (about eight times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Subcard slots

Table2-194 Subcard slots

Card model	Number of subcard slots
CSPEX-2314X-G1	4

Technical specifications

Table2-195 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 × 399 × 352 mm (2.07 × 15.71 × 13.86 in)
Weight	5.15 kg (11.35 lb)
Maximum power consumption	320 W
Power consumption (with typical configuration)	268 W
Minimum power consumption	120 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CSPEX-2314X-G2

View

Figure2-41 CSPEX-2314X-G2 view

(1) Card status LED. For the LED description, see Table2-196.

LEDs

Table2-196 LED description

LED	Status	Description
RUN (Green)	Steady on	The card is faulty.
	Off	The card is faulty or is not in position.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing (about eight times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Subcard slots

Table2-197 Subcard slots

Card model	Number of subcard slots
CSPEX-2314X-G2	4

Technical specifications

Table2-198 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 × 399 × 352 mm (2.07 × 15.71 × 13.86 in)
Weight	5.15 kg (11.35 lb)
Maximum power consumption	320 W
Power consumption (with typical configuration)	268 W
Minimum power consumption	120 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CSPEX-2612X3-E

View

Figure2-42 CSPEX-2612X3-E view

(1) Card status LED. For the LED description, see Table2-199.

LEDs

Table2-199 LED description

LED	Status	Description
RUN (Green)	Steady on	The card is faulty.
	Off	The card is faulty or is not in position.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing (about eight times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Subcard slots

Table2-200 Subcard slots

Card model	Number of subcard slots
CSPEX-2612X3-E	2

Technical specifications

Table2-201 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 × 399 × 352 mm (2.07 × 15.71 × 13.86 in)
Weight	9.00 kg (19.84 lb)
Maximum power consumption	610 W
Power consumption (with typical configuration)	410 W
Minimum power consumption	317 W
Operating temperature	0°C to 45°C (32°F to 113°F)

Configuration restrictions and guidelines

An SR8804-X router installed with Type-A switching fabric modules does not support the CSPEX-1304X, CSPEX-1404X, or CSPEX-1504X cards.

For adequate ventilation and cooling, you can install the CSPEX-1602X cards in the following slots only when the other slots are not available.

· SR8808-X router—Slots 0, 8 and 9.

· SR8812-X router—Slots 0 and 13.

Compatibility information

Table2-202 Compatibility matrix between SPEX/CSPEX cards and routers

Card model	SR8804-X	SR8808-X	SR8812-X	SR8808H-X, SR8816-X
SPEX-1204	Supported	Supported	Supported	Not supported
CSPEX-1104-E	Supported	Supported	Supported	Not supported
CSPEX-1304X	Supported	Supported	Supported	Supported
CSPEX-1404X	Supported	Supported	Supported	Supported
CSPEX-1502X	Not supported	Supported	Supported	Supported
CSPEX-1504X	Supported	Supported	Supported	Supported
CSPEX-1602X	Not supported	Supported	Supported	Supported
CSPEX-1802X	Not supported	Not supported	Not supported	Supported
CSPEX-1802XB	Not supported	Not supported	Not supported	Supported
CSPEX-1804X	Not supported	Not supported	Not supported	Supported
CSPEX-1512X	Not supported	Not supported	Not supported	Supported
CSPEX-1612X	Not supported	Not supported	Not supported	Supported
CSPEX-1812X	Not supported	Not supported	Not supported	Supported
CSPEX-1812X-E	Not supported	Not supported	Not supported	Supported
CSPEX-2304X-G	Supported	Supported	Not supported	Supported
CSPEX-2304X-G2	Supported	Supported	Supported	Supported
CSPEX-2304X-LG	Supported	Supported	Not supported	Supported
CSPEX-2314X-G	Not supported	Not supported	Not supported	Supported
CSPEX-2314X-G1	Not supported	Not supported	Not supported	Supported
CSPEX-2314X-G2	Not supported	Not supported	Not supported	Supported
CSPEX-2612X-E	Not supported	Not supported	Not supported	Supported
CSPEX-2612X3-E	Not supported	Not supported	Not supported	Supported

Table2-203 Compatibility matrixes between SPEX/CSPEX cards and subcards (1)

Subcard model	SPEX/CSPEX card
Subcard model	SPEX-1204	CSPEX-1304X	CSPEX-1504X/CSPEX-1404X/CSPEX-2304X-G2	CSPEX-1502X	CSPEX-1602X	CSPEX-1804X
GIC-CLP2L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-CQ1LF	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-CQ1L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-ET16L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-GP12L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-GT10L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-MSC-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-PSP4L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-SP4L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-SP8L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-TCP8L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-XP4L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-XP6L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-XP12LF	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-XP12L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
PIC-GP10L	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Not supported	Not supported	Not supported	Not supported	Not supported
PIC-TCP8L	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Not supported	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Not supported	Not supported	Not supported
PIC-PSP4L	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Not supported	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Not supported	Not supported	Not supported
PIC-PS2G4L	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Not supported	Not supported	Not supported	Not supported	Not supported
PIC-PUP1L	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Not supported	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Not supported	Not supported	Not supported
PIC-XP1L	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GT20L	Not supported	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Not supported	Not supported	Not supported
MIC-GT20L1	Not supported	Not supported	Supported only by CSPEX-1504X and CSPEX-2304X-G2	Not supported	Not supported	Not supported
MIC-ET16L	Supported	Supported	Supported	Not supported	Not supported	Not supported
MIC-CLP2L	Supported	Supported	Supported	Not supported	Not supported	Not supported
MIC-CLP4L	Supported	Supported	Supported	Not supported	Not supported	Not supported
MIC-SP4L	Supported	Supported	Supported	Not supported	Not supported	Not supported
MIC-SP8L	Supported	Supported	Supported	Not supported	Not supported	Not supported
MIC-GP4L	Subcard slots 1 and 2: Not supported. Subcard slots 3 and 4: Supported.	Supported	Supported	Not supported	Not supported	Not supported
MIC-GP8L	Subcard slots 1 and 2: Not supported. Subcard slots 3 and 4: Supported.	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GP10L1	Subcard slots 1 and 2: Not supported. Subcard slots 3 and 4: Supported.	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GP10L2	Not supported	Not supported	Supported only by CSPEX-1504X and CSPEX-2304X-G2	Not supported	Not supported	Not supported
MIC-GP10L-V2	Not supported	Subcard slots 1, 2, and 3: Supported. Subcard slot 4: Not supported.	Supported	Not supported	Not supported	Not supported
MIC-GP20L	Not supported	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Not supported	Not supported	Not supported
MIC-GP20L1	Not supported	Not supported	Not supported	Supported	Supported	Not supported
MIC-XP2L	Not supported	Supported	Supported	Not supported	Not supported	Not supported
MIC-XP2L-LAN	Not supported	Supported	Supported	Not supported	Not supported	Not supported
MIC-XP4L1	Not supported	Supported	Supported	Not supported	Not supported	Not supported
MIC-XP5L	Not supported	Supported	Supported	Not supported	Not supported	Not supported
MIC-XP5L1	Not supported	Supported	Supported	Not supported	Not supported	Not supported
MIC-XP5L2	Not supported	Supported	Supported	Not supported	Not supported	Not supported
MIC-XP8L	Not supported	Not supported	Not supported	Supported	Not supported	Not supported
MIC-XP10LF	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-XP10L-LAN	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-XP20L	Not supported	Not supported	Not supported	Supported	Supported	Not supported
MIC-QP1L	Not supported	Supported	Supported	Not supported	Not supported	Not supported
MIC-CP1L	Not supported	Not supported	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Not supported	Not supported	Not supported
MIC-CP1L-V2	Not supported	Not supported	Not supported	Not supported	Not supported	Supported
MIC-CP2L	Not supported	Not supported	Not supported	Supported	Supported	Not supported
MIC-CP2L-V2	Not supported	Not supported	Not supported	Not supported	Not supported	Supported
MIC-CQ1L1	Not supported	Not supported	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Not supported	Not supported	Not supported
MIC-CQ1L2	Not supported	Not supported	Not supported.	Not supported	Not supported	Not supported
MIC-CQ1LF	Not supported	Not supported	Not supported.	Not supported	Not supported	Not supported
MIC-CQ2L	Not supported	Not supported	Not supported	Supported	Supported	Not supported
MIC-PSP4L	Not supported	Supported	Supported	Not supported	Not supported	Not supported
MIC-TCP8L	Not supported	Subcard slots 1, 2, and 3: Supported. Subcard slot 4: Not supported.	Supported	Not supported	Not supported	Not supported
MIC-SEC	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-GT20L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-QP3L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-GP20L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-GP24L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-GP24L1	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-GP24L1B	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-XP5L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-XP10L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-XP20L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-XP20L1	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-XP20L1B	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-CC1L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-CC2L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-CQ1L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-CQ2L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-CQ2LB	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-GP20L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-XP5L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-XP10L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-XP20L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-YGS4L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-LGQ2L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-LGQ4L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-CQ1LF	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-CQ2LF	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-CC1L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-CC2L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported

Table2-204 Compatibility matrixes between SPEX/CSPEX cards and subcards (2)

Subcard model	SPEX/CSPEX card
Subcard model	CSPEX-1104-E	CSPEX-1512X	CSPEX-1612X	CSPEX-1812X	CSPEX-1812X-E	CSPEX-1802X
GIC-CLP2L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-CQ1LF	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-CQ1L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-ET16L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-GP12L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-GT10L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-MSC-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-PSP4L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-SP4L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-SP8L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-TCP8L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-XP4L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-XP6L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-XP12LF	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
GIC-XP12L-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
PIC-GP10L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
PIC-XP1L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
PIC-TCP8L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
PIC-PS2G4L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
PIC-PSP4L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
PIC-PUP1L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GP4L	Supported, a maximum of 3.	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GP8L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GP10L1	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GP10L2	Supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-SP4L	Supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-CLP2L	Supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-CLP4L	Supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-SP8L	Supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-ET16L	Supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GP20L	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GP20L1	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GT20L	Subcard slots 1 and 2: Supported. Subcard slots 3 and 4: Not supported.	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GT20L1	Supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-CP1L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GP10L-V2	Supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-XP2L	Supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-XP2L-LAN	Supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-XP4L1	Supported, a maximum of 3	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-XP5L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-XP8L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-XP10LF	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-XP10L-LAN	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-XP5L1	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-XP5L2	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-XP20L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-CP2L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-QP1L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-CP1L-V2	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-CP2L-V2	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-CQ1L1	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-CQ1L2	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-CQ1LF	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-CQ2L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-PSP4L	Supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-TCP8L	Supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-SEC	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-GT20L	Not supported	Supported	Supported	Supported	Not supported	Not supported
NIC-QP3L	Not supported	Not supported	Not supported	Not supported	Not supported	Supported
NIC-GP20L	Not supported	Supported	Supported	Supported	Not supported	Not supported
NIC-GP24L	Not supported	Supported	Supported	Supported	Not supported	Not supported
NIC-GP24L1	Not supported	Not supported	Not supported	Not supported	Supported	Supported
NIC-GP24L1B	Not supported	Not supported	Not supported	Not supported	Not supported	Supported
NIC-XP5L	Not supported	Supported	Supported	Supported	Supported	Supported
NIC-XP10L	Not supported	Supported	Supported	Supported	Supported	Supported
NIC-XP20L	Not supported	Not supported	Not supported	Supported	Supported	Supported
NIC-XP20L1	Not supported	Not supported	Not supported	Supported	Supported	Supported
NIC-XP20L1B	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-CC1L	Not supported	Not supported	Supported	Supported	Supported	Supported
NIC-CC2L	Not supported	Not supported	Not supported	Supported	Supported	Supported
NIC-CQ1L	Not supported	Not supported	Supported	Supported	Supported	Supported
NIC-CQ2L	Not supported	Not supported	Not supported	Supported	Supported	Supported
NIC-CQ2LB	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-GP20L	Not supported	Supported	Supported	Supported	Not supported	Not supported
RX-NIC-XP5L	Not supported	Supported	Supported	Supported	Supported	Supported
RX-NIC-XP10L	Not supported	Supported	Supported	Supported	Supported	Supported
RX-NIC-XP20L	Not supported	Not supported	Not supported	Supported	Supported	Supported
RX-NIC-YGS4L	Not supported	Not supported	Not supported	Supported	Supported	Supported
RX-NIC-LGQ2L	Not supported	Not supported	Not supported	Supported	Supported	Supported
RX-NIC-LGQ4L	Not supported	Not supported	Not supported	Supported	Not supported	Supported
RX-NIC-CQ1LF	Not supported	Not supported	Not supported	Supported	Supported	Supported
RX-NIC-CQ2LF	Not supported	Not supported	Not supported	Supported	Supported	Supported
RX-NIC-CC1L	Not supported	Supported	Supported	Supported	Supported	Supported
RX-NIC-CC2L	Not supported	Not supported	Not supported	Supported	Supported	Supported

Table2-205 Compatibility matrixes between SPEX/CSPEX cards and subcards (3)

Subcard model	SPEX/CSPEX card
Subcard model	CSPEX-1802XB	CSPEX-2304X-G CSPEX-2304X-LG	CSPEX-2314X-G	CSPEX-2314X-G1 CSPEX-2314X-G2	CSPEX-2612X-E	CSPEX-2612X3-E
GIC-CLP2L-G	Not supported	Not supported	Supported	Supported	Not supported	Not supported
GIC-CQ1LF	Not supported	Not supported	Supported	Supported (only in subcard slots 1 and 2)	Not supported	Not supported
GIC-CQ1L-G	Not supported	Not supported	Supported	Supported	Not supported	Not supported
GIC-ET16L-G	Not supported	Not supported	Supported	Supported	Not supported	Not supported
GIC-GP12L-G	Not supported	Not supported	Supported	Supported	Not supported	Not supported
GIC-GT10L-G	Not supported	Not supported	Supported	Supported	Not supported	Not supported
GIC-MSC-G	Not supported	Not supported	Supported	Supported	Not supported	Not supported
GIC-PSP4L-G	Not supported	Not supported	Supported	Supported	Not supported	Not supported
GIC-SP4L-G	Not supported	Not supported	Supported	Supported	Not supported	Not supported
GIC-SP8L-G	Not supported	Not supported	Supported	Supported	Not supported	Not supported
GIC-TCP8L-G	Not supported	Not supported	Supported	Supported	Not supported	Not supported
GIC-XP4L-G	Not supported	Not supported	Supported	Supported	Not supported	Not supported
GIC-XP6L-G	Not supported	Not supported	Supported	Supported	Not supported	Not supported
GIC-XP12LF	Not supported	Not supported	Supported	Supported (only in subcard slots 1 and 2)	Not supported	Not supported
GIC-XP12L-G	Not supported	Not supported	Supported	Supported	Not supported	Not supported
PIC-GP10L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
PIC-XP1L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
PIC-TCP8L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
PIC-PS2G4L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
PIC-PSP4L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
PIC-PUP1L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GP4L	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-GP8L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GP10L1	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GP10L2	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-SP4L	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-CLP2L	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-CLP4L	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-SP8L	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-ET16L	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-GP20L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GP20L1	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GT20L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GT20L1	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-CP1L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-GP10L-V2	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-XP2L	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-XP2L-LAN	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-XP4L1	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-XP5L	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-XP8L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-XP10LF	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-XP10L-LAN	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-XP5L1	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-XP5L2	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-XP20L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-CP2L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-QP1L	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-CP1L-V2	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-CP2L-V2	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-CQ1L1	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-CQ1L2	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-CQ1LF	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-CQ2L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MIC-PSP4L	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-TCP8L	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
MIC-SEC	Not supported	Supported	Not supported	Not supported	Not supported	Not supported
NIC-GT20L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-QP3L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-GP20L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-GP24L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-GP24L1	Not supported	Not supported	Not supported	Not supported	Supported	Not supported
NIC-GP24L1B	Supported	Not supported	Not supported	Not supported	Not supported	Supported
NIC-XP5L	Not supported	Not supported	Not supported	Not supported	Supported	Not supported
NIC-XP10L	Not supported	Not supported	Not supported	Not supported	Supported	Not supported
NIC-XP20L	Not supported	Not supported	Not supported	Not supported	Not supported	Supported
NIC-XP20L1	Not supported	Not supported	Not supported	Not supported	Supported	Not supported
NIC-XP20L1B	Supported	Not supported	Not supported	Not supported	Not supported	Supported
NIC-CC1L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-CC2L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
NIC-CQ1L	Not supported	Not supported	Not supported	Not supported	Supported	Supported
NIC-CQ2L	Not supported	Not supported	Not supported	Not supported	Supported	Not supported
NIC-CQ2LB	Supported	Not supported	Not supported	Not supported	Not supported	Supported
RX-NIC-GP20L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-XP5L	Not supported	Not supported	Not supported	Not supported	Supported	Not supported
RX-NIC-XP10L	Not supported	Not supported	Not supported	Not supported	Supported	Not supported
RX-NIC-XP20L	Not supported	Not supported	Not supported	Not supported	Supported	Not supported
RX-NIC-YGS4L	Not supported	Not supported	Not supported	Not supported	Supported	Not supported
RX-NIC-LGQ2L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-LGQ4L	Not supported	Not supported	Not supported	Not supported	Supported	Not supported
RX-NIC-CQ1LF	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-CQ2LF	Not supported	Not supported	Not supported	Not supported	Supported	Not supported
RX-NIC-CC1L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-NIC-CC2L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported

MPE base cards

MPE-1104

View

Figure2-43 MPE-1104 view

(1) Card status LED. For the LED description, see Table2-206.

LEDs

Table2-206 LED description

LED	Status	Description
RUN (green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing (about eight times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Subcard slots

Table2-207 Subcard slots

Card model	Number of subcard slots
MPE-1104	4

Technical specifications

Table2-208 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.52 kg (7.76 lb)
Maximum power consumption	158 W
Typical power consumption	94 W
Minimum power consumption	91 W
Operating temperature	0°C to 45°C (32°F to 113°F)

Configuration restrictions and guidelines

The subslot restrictions of an MPE card depend on the subslot mode. For more information about subslot modes, see H3C SR8800-X Routers Configuration Guides.

Compatibility information

Table2-209 Compatibility matrix between MPE cards and routers

Card model	SR8804-X	SR8808-X, SR8812-X	SR8808H-X, SR8816-X
MPE-1104	Supported	Supported	Not supported

Table2-210 Compatibility matrix between MPE cards and subcards

Subcard model	MPE cards
GIC-CLP2L-G	Not supported
GIC-CQ1LF	Not supported
GIC-CQ1L-G	Not supported
GIC-ET16L-G	Not supported
GIC-GP12L-G	Not supported
GIC-GT10L-G	Not supported
GIC-MSC-G	Not supported
GIC-PSP4L-G	Not supported
GIC-SP4L-G	Not supported
GIC-SP8L-G	Not supported
GIC-TCP8L-G	Not supported
GIC-XP4L-G	Not supported
GIC-XP6L-G	Not supported
GIC-XP12LF	Not supported
GIC-XP12L-G	Not supported
PIC-GP10L	Not supported
PIC-TCP8L	Not supported
PIC-PSP4L	Not supported
PIC-PS2G4L	Not supported
PIC-PUP1L	Not supported
PIC-XP1L	Not supported
MIC-GT20L	Not supported
MIC-GT20L1	Not supported
MIC-CLP4L	Supported
MIC-ET16L	Supported
MIC-CLP2L	Supported
MIC-SP8L	Only one is supported. Can be installed only slot 1 or slot 2.
MIC-SP4L	Supported
MIC-GP4L	Supported
MIC-GP8L	Not supported in slot 3 or slot 4
MIC-GP10L1	Not supported
MIC-GP10L2	Not supported
MIC-GP10L-V2	Not supported
MIC-GP20L	Not supported
MIC-GP20L1	Not supported
MIC-XP2L	Not supported
MIC-XP2L-LAN	Not supported
MIC-XP4L1	Not supported
MIC-XP5L	Not supported
MIC-XP5L1	Not supported
MIC-XP5L2	Not supported
MIC-XP8L	Not supported
MIC-XP10LF	Not supported
MIC-XP10L-LAN	Not supported
MIC-XP20L	Not supported
MIC-QP1L	Not supported
MIC-CP1L	Not supported
MIC-CP1L-V2	Not supported
MIC-CP2L	Not supported
MIC-CP2L-V2	Not supported
MIC-CQ1L1	Not supported
MIC-CQ1L2	Not supported
MIC-CQ1LF	Not supported
MIC-CQ2L	Not supported
MIC-PSP4L	Not supported
MIC-TCP8L	Not supported
MIC-SEC	Not supported
NIC-GT20L	Not supported
NIC-QP3L	Not supported
NIC-GP20L	Not supported
NIC-GP24L	Not supported
NIC-GP24L1	Not supported
NIC-GP24L1B	Not supported
NIC-XP5L	Not supported
NIC-XP10L	Not supported
NIC-XP20L	Not supported
NIC-XP20L1	Not supported
NIC-XP20L1B	Not supported
NIC-CC1L	Not supported
NIC-CC2L	Not supported
NIC-CQ1L	Not supported
NIC-CQ2L	Not supported
NIC-CQ2LB	Not supported
RX-NIC-GP20L	Not supported
RX-NIC-XP5L	Not supported
RX-NIC-XP10L	Not supported
RX-NIC-XP20L	Not supported
RX-NIC-YGS4L	Not supported
RX-NIC-LGQ2L	Not supported
RX-NIC-LGQ4L	Not supported
RX-NIC-CQ1LF	Not supported
RX-NIC-CQ2LF	Not supported
RX-NIC-CC1L	Not supported
RX-NIC-CC2L	Not supported

SPE base cards

RX-SPE200/RX-SPE200-E

View

Figure2-44 RX-SPE200 view

(1) Card status LED. For the LED description, see Table2-211.

The views of the RX-SPE200 and RX-SPE200-E are similar. This figure uses the RX-SPE200 as an example.

LEDs

Table2-211 LED description

LED	Status	Description
RUN (green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing (about eight times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Subcard slots

Table2-212 Subcard slots

Card model	Number of subcard slots
RX-SPE200	2
RX-SPE200-E	2

Technical specifications

Table2-213 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 mm × 399 mm × 352 mm (2.07 in × 15.71 in × 13.86 in)
Weight	· RX-SPE200: 5.35 kg (11.79 lb) · RX-SPE200-E: 5.00 kg (11.02 lb)
Maximum power consumption	· RX-SPE200: 530 W · RX-SPE200-E: 270 W
Typical power consumption	· RX-SPE200: 300 W · RX-SPE200-E: 135 W
Minimum power consumption	· RX-SPE200: 280 W · RX-SPE200-E: 120 W
Operating temperature	0°C to 45°C (32°F to 113°F)

Compatibility information

Table2-214 Compatibility matrix between SPE cards and routers

Card model	SR8804-X	SR8808-X, SR8812-X	SR8808H-X, SR8816-X
RX-SPE200	Not supported	Not supported	Supported
RX-SPE200-E	Not supported	Not supported	Supported

Table2-215 Compatibility matrix between SPE cards and subcards

Subcard model	RX-SPE200	RX-SPE200-E
GIC-CLP2L-G	Not supported	Not supported
GIC-CQ1LF	Not supported	Not supported
GIC-CQ1L-G	Not supported	Not supported
GIC-ET16L-G	Not supported	Not supported
GIC-GP12L-G	Not supported	Not supported
GIC-GT10L-G	Not supported	Not supported
GIC-MSC-G	Not supported	Not supported
GIC-PSP4L-G	Not supported	Not supported
GIC-SP4L-G	Not supported	Not supported
GIC-SP8L-G	Not supported	Not supported
GIC-TCP8L-G	Not supported	Not supported
GIC-XP4L-G	Not supported	Not supported
GIC-XP6L-G	Not supported	Not supported
GIC-XP12LF	Not supported	Not supported
GIC-XP12L-G	Not supported	Not supported
PIC-GP10L	Not supported	Not supported
PIC-TCP8L	Not supported	Not supported
PIC-PSP4L	Not supported	Not supported
PIC-PS2G4L	Not supported	Not supported
PIC-PUP1L	Not supported	Not supported
PIC-XP1L	Not supported	Not supported
MIC-GT20L	Not supported	Not supported
MIC-GT20L1	Not supported	Not supported
MIC-CLP4L	Not supported	Not supported
MIC-ET16L	Not supported	Not supported
MIC-CLP2L	Not supported	Not supported
MIC-SP8L	Not supported	Not supported
MIC-SP4L	Not supported	Not supported
MIC-GP4L	Not supported	Not supported
MIC-GP8L	Not supported	Not supported
MIC-GP10L1	Not supported	Not supported
MIC-GP10L2	Not supported	Not supported
MIC-GP10L-V2	Not supported	Not supported
MIC-GP20L	Not supported	Not supported
MIC-GP20L1	Not supported	Not supported
MIC-XP2L	Not supported	Not supported
MIC-XP2L-LAN	Not supported	Not supported
MIC-XP4L1	Not supported	Not supported
MIC-XP5L	Not supported	Not supported
MIC-XP5L1	Not supported	Not supported
MIC-XP5L2	Not supported	Not supported
MIC-XP8L	Not supported	Not supported
MIC-XP10LF	Not supported	Not supported
MIC-XP10L-LAN	Not supported	Not supported
MIC-XP20L	Not supported	Not supported
MIC-QP1L	Not supported	Not supported
MIC-CP1L	Not supported	Not supported
MIC-CP1L-V2	Not supported	Not supported
MIC-CP2L	Not supported	Not supported
MIC-CP2L-V2	Not supported	Not supported
MIC-CQ1L1	Not supported	Not supported
MIC-CQ2L	Not supported	Not supported
MIC-PSP4L	Not supported	Not supported
MIC-TCP8L	Not supported	Not supported
MIC-SEC	Not supported	Not supported
NIC-GT20L	Supported	Not supported
NIC-QP3L	Supported	Supported
NIC-GP20L	Supported	Not supported
NIC-GP24L	Supported	Not supported
NIC-GP24L1	Not supported	Supported
NIC-GP24L1B	Not supported	Not supported
NIC-XP5L	Not supported	Not supported
NIC-XP10L	Supported	Not supported
NIC-XP20L	Not supported	Not supported
NIC-XP20L1	Not supported	Not supported
NIC-XP20L1B	Not supported	Not supported
NIC-CC1L	Not supported	Not supported
NIC-CC2L	Not supported	Not supported
NIC-CQ1L	Supported	Not supported
MIC-CQ1L2	Not supported	Not supported
MIC-CQ1LF	Not supported	Not supported
NIC-CQ2L	Not supported	Not supported
NIC-CQ2LB	Not supported	Not supported
RX-NIC-GP20L	Supported	Not supported
RX-NIC-XP5L	Supported	Supported
RX-NIC-XP10L	Supported	Supported
RX-NIC-XP20L	Not supported	Not supported
RX-NIC-YGS4L	Supported	Supported
RX-NIC-LGQ2L	Supported	Supported
RX-NIC-LGQ4L	Not supported	Not supported
RX-NIC-CQ1LF	Supported	Supported
RX-NIC-CQ2LF	Not supported	Not supported
RX-NIC-CC1L	Supported	Supported
RX-NIC-CC2L	Not supported	Not supported

GIC subcards

IMPORTANT:

· To use a GIC interface card, you must install it on a CSPEX base card. You cannot install it directly on the router.

· For the compatibility between GIC interface cards and CSPEX base cards, see the compatibility information for the base cards.

· Some GIC subcards support changing the speed and operating mode. For more information, see H3C SR8800-X Routers Configuration Guides.

GIC-CLP2L-G

View

Figure2-45 GIC-CLP2L-G view

(1) OC-3/STM-1 SFP fiber ports (2 in total)

(2) Port LED. For the LED description, see Table2-216.

LEDs

Table2-216 WAN port LED description

LED	Status	Description
WAN port LED (ACT/ALM)	Steady green	A link is present on the WAN port.
	Flashing green	The WAN port is receiving or sending data correctly.
	Steady yellow	A transceiver module has been installed in the WAN port, but an alarm has occurred.
	Off	No transceiver module is installed in the WAN port.

Ports

Table2-217 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
GIC-CLP2L-G	2-port OC-3/STM-1 (155M) channelized POS optical interface card	LC	2	155 Mbps (OC-3/STM-1)

Technical specifications

Table2-218 Technical specifications

Item	Description
Dimensions (H × W × D)	22.3 × 190 × 154 mm (0.88 × 7.48 × 6.06 in)
Weight	1.05 kg (2.31 lb)
Maximum power consumption	18 W
Minimum power consumption	16 W
Operating temperature	0°C to 45°C (32°F to 113°F)

GIC-CQ1LF

View

Figure2-46 GIC-CQ1LF view

(1) 100G/50G/40G fiber port (1 in total)	(2) 50G/40G fiber port (1 in total)
(3) 50G/40G fiber port LED. For the LED description, see Table2-219.	(4) 100G/50G/40G fiber port LED. For the LED description, see Table2-219.

LEDs

Table2-219 Fiber port LED description

LED	Status	Description
Fiber port LED (LINK/ACT)	Flashing	The port is receiving or sending data.
	On	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of a QSFP28 port by observing the color of its LED. Green indicates a speed of 100 Gbps, and yellow indicates a speed of 50 Gbps or 40 Gbps.

Ports

Table2-220 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
GIC-CQ1LF	2-port 50G/1-port 100G flexible Ethernet optical interface card	LC	1	100 Gbps
			2	40 Gbps
			2	50 Gbps

NOTE:

You can change the speed of only port 1 to 100 Gbps. After the change, port 2 is unavailable. For more information about the commands used for changing the speed of ports on the subcard, see H3C SR8800-X Routers Command Reference.

Technical specifications

Table2-221 Technical specifications

Item	Description
Dimensions (H × W × D)	22.3 × 190 × 154 mm (0.88 × 7.48 × 6.06 in)
Weight	0.75 kg (1.65 lb)
Maximum power consumption	50 W
Minimum power consumption	27 W
Operating temperature	0°C to 45°C (32°F to 113°F)

GIC-CQ1L-G

View

Figure2-47 GIC-CQ1L-G view

(1) 100GBASE-R QSFP28 fiber port (1 in total)

(2) QSFP28 port LED. For the LED description, see Table2-222.

LEDs

Table2-222 QSFP28 port LED description

LED	Status	Description
QSFP28 port LED	Flashing	The QSFP28 port is receiving or sending data.
	On	A link is present on the QSFP28 port.
	Off	No link is present on the QSFP28 port.

NOTE:

You can identify the speed of a QSFP28 port by observing the color of its LED. Green indicates a speed of 100 Gbps, and yellow indicates a speed of 10 Gbps.

Ports

Table2-223 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
GIC-CQ1L-G	1-port 100G Ethernet optical interface card	LC	1	100 Gbps
GIC-CQ1L-G	1-port 100G Ethernet optical interface card	LC	1	10 Gbps

Technical specifications

Table2-224 Technical specifications

Item	Description
Dimensions (H × W × D)	22.3 × 190 × 154 mm (0.88 × 7.48 × 6.06 in)
Weight	1.00 kg (2.20 lb)
Maximum power consumption	15 W
Minimum power consumption	13 W
Operating temperature	0°C to 45°C (32°F to 113°F)

GIC-ET16L-G

View

Figure2-48 GIC-ET16L-G view

(1) E1-HM96 copper ports (16 in total)

(2) Port LED. For the LED description, see Table2-225.

LEDs

Table2-225 WAN port LED description

LED	Status	Description
ACT/ALM	Steady green	A link is present on the port.
	Flashing green	The port is receiving or sending data correctly.
	Steady yellow	An E1 cable is has been connected to the port, but an alarm has occurred.
	Off	No E1 cable is connected to the port.

Ports

Table2-226 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
GIC-ET16L-G	16-port E1 copper interface card	HM96 male connector	16	E1

Technical specifications

Table2-227 Technical specifications

Item	Description
Dimensions (H × W × D)	22.3 × 190 × 154 mm (0.88 × 7.48 × 6.06 in)
Weight	1.00 kg (2.20 lb)
Maximum power consumption	14 W
Minimum power consumption	12 W
Operating temperature	0°C to 45°C (32°F to 113°F)

GIC-GP12L-G

View

Figure2-49 GIC-GP12L-G view

(1) 1000BASE-X SFP fiber ports (12 in total)

(2) SFP port LED. For the LED description, see Table2-228.

LEDs

Table2-228 GE SFP port LED description

LED	Status	Description
GE SFP port LED (LINK/ACT)	Flashing	The SFP port is receiving or sending data.
	On	A link is present on the SFP port.
	Off	No link is present on the SFP port.

NOTE:

You can identify the speed of an SFP port by observing the color of its LED. Green indicates a speed of 1000 Mbps, and yellow indicates a speed of 10/100 Mbps.

Ports

Table2-229 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
GIC-GP12L-G	12-port 1000BASE-X Ethernet optical interface card	LC	12	10/100/1000 Mbps

Technical specifications

Table2-230 Technical specifications

Item	Description
Dimensions (H × W × D)	22.3 × 190 × 154 mm (0.88 × 7.48 × 6.06 in)
Weight	1.05 kg (2.31 lb)
Maximum power consumption	26 W
Minimum power consumption	15 W
Operating temperature	0°C to 45°C (32°F to 113°F)

GIC-GT10L-G

View

Figure2-50 GIC-GT10L-G view

(1) RJ45 Ethernet port LEDs. For the LED description, see Table2-231.

(2) 10/100/1000BASE-T copper ports (10 in total)

LEDs

Table2-231 RJ45 Ethernet port LED description

LED	Status	Description
RJ45 Ethernet port LED	LINK: Steady green	A 1000 Mbps link is present on the port.
	LINK: Flashing green	The port is receiving or sending data at 1000 Mbps.
	ACT: Steady yellow	A 10/100 Mbps link is present on the port.
	ACT: Flashing yellow	The port is receiving or sending data at 10/100 Mbps.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an RJ45 Ethernet port by observing the color of its LEDs. A green LINK LED indicates a speed of 1000 Mbps, and a yellow ACT LED indicates a speed of 10/100 Mbps.

Ports

Table2-232 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
GIC-GT10L-G	10-port 1000BASE-T Ethernet copper interface card	RJ45	10	10/100/1000 Mbps

Technical specifications

Table2-233 Technical specifications

Item	Description
Dimensions (H × W × D)	22.3 × 190 × 154 mm (0.88 × 7.48 × 6.06 in)
Weight	0.77 kg (1.70 lb)
Maximum power consumption	20 W
Minimum power consumption	17 W
Operating temperature	0°C to 45°C (32°F to 113°F)

GIC-MSC-G

View

Figure2-51 GIC-MSC-G view

Ports

Table2-234 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
GIC-MSC-G	Network data mutiservice processing interface card (GIC)	N/A	N/A	N/A

Technical specifications

Table2-235 Technical specifications

Item	Description
Dimensions (H × W × D)	22.3 × 190 × 154 mm (0.88 × 7.48 × 6.06 in)
Weight	0.70 kg (1.54 lb)
Maximum power consumption	13 W
Minimum power consumption	11 W
Operating temperature	0°C to 45°C (32°F to 113°F)

GIC-PSP4L-G

View

Figure2-52 GIC-PSP4L-G view

(1) OC-48c/STM-16c POS fiber ports (4 in total)

(2) Port LED. For the LED description, see Table2-236.

LEDs

Table2-236 WAN port LED description

LED	Status	Description
WAN port LED (ACT/ALM)	Steady green	A link is present on the WAN port.
	Flashing green	The WAN port is receiving or sending data correctly.
	Steady yellow	A transceiver module has been installed in the WAN port, but an alarm has occurred.
	Off	No transceiver module is installed in the WAN port.

Ports

Table2-237 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
GIC-PSP4L-G	4-port OC-48c/STM-16c (2.5G) POS optical interface card	LC	4	2.5 Gbps

Technical specifications

Table2-238 Technical specifications

Item	Description
Dimensions (H × W × D)	22.3 × 190 × 154 mm (0.88 × 7.48 × 6.06 in)
Weight	0.74 kg (1.63 lb)
Maximum power consumption	20 W
Minimum power consumption	16 W
Operating temperature	0°C to 45°C (32°F to 113°F)

GIC-SP4L-G

View

Figure2-53 GIC-SP4L-G view

(1) Four OC-3/STM-1c POS/ATM fiber ports or one OC-12c/STM-4c POS/ATM fiber port (only port 1 supports OC-12c/STM-4c)

(2) Port LED. For the LED description, see Table2-239.

LEDs

Table2-239 WAN port LED description

LED	Status	Description
WAN port LED (ACT/ALM)	Steady green	A link is present on the WAN port.
	Flashing green	The WAN port is receiving or sending data correctly.
	Steady yellow	A transceiver module has been installed in the WAN port, but an alarm has occurred.
	Off	No transceiver module is installed in the WAN port.

Ports

Table2-240 Port specifications

Card model

Description

Connector type

Port quantity

Port transmission speed

GIC-SP4L-G

4-port OC-3c/STM-1c (155M) POS/ATM or 1-port OC-12c/STM-4c (622M) POS/ATM optical interface card

The card does not support switching to ATM mode.

155 Mbps (OC-3/STM-1)

622 Mbps (OC-12/STM-4)

NOTE:

You can change the speed of only port 1 to 622 Mbps. After the change, other ports are unavailable. For more information about the command used for changing the operating mode of the subcard, see H3C SR8800-X Routers Command Reference.

Technical specifications

Table2-241 Technical specifications

Item	Description
Dimensions (H × W × D)	22.3 × 190 × 154 mm (0.88 × 7.48 × 6.06 in)
Weight	0.74 kg (1.63 lb)
Maximum power consumption	20 W
Minimum power consumption	16 W
Operating temperature	0°C to 45°C (32°F to 113°F)

GIC-SP8L-G

View

Figure2-54 GIC-SP8L-G view

(1) OC-3c/STM-1c POS fiber ports (8 in total)

(2) Port LED. For the LED description, see Table2-242.

LEDs

Table2-242 WAN port LED description

LED	Status	Description
WAN port LED (ACT/ALM)	Steady green	A link is present on the WAN port.
	Flashing green	The WAN port is receiving or sending data correctly.
	Steady yellow	A transceiver module has been installed in the WAN port, but an alarm has occurred.
	Off	No transceiver module is installed in the WAN port.

Ports

Table2-243 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
GIC-SP8L-G	8-port OC-3c/STM-1c (155M) POS optical interface card	LC	8	155 Mbps (OC-3/STM-1)

Technical specifications

Table2-244 Technical specifications

Item	Description
Dimensions (H × W × D)	22.3 × 190 × 154 mm (0.88 × 7.48 × 6.06 in)
Weight	0.75 kg (1.65 lb)
Maximum power consumption	24 W
Minimum power consumption	16 W
Operating temperature	0°C to 45°C (32°F to 113°F)

GIC-TCP8L-G

View

Figure2-55 GIC-TCP8L-G view

(1) OC-3c/OC-12c POS/GE fiber ports (8 in total)

(2) Port LED. For the LED description, see Table2-245.

LEDs

Table2-245 WAN port LED description

LED	Status	Description
WAN port LED (ACT/ALM)	Steady green	A link is present on the WAN port.
	Flashing green	The WAN port is receiving or sending data correctly.
	Steady yellow	A transceiver module has been installed in the WAN port, but an alarm has occurred.
	Off	No transceiver module is installed in the WAN port.

Ports

Table2-246 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
GIC-TCP8L-G	8-port OC-3c/OC-12c (622M/155M) POS/GE optical interface card	LC	8	155 Mbps (OC-3/STM-1)
				622 Mbps (OC-12/STM-4)
				10/100/1000 Mbps

Technical specifications

Table2-247 Technical specifications

Item	Description
Dimensions (H × W × D)	22.3 × 190 × 154 mm (0.88 × 7.48 × 6.06 in)
Weight	1.05 kg (2.31 lb)
Maximum power consumption	24 W
Minimum power consumption	16 W
Operating temperature	0°C to 45°C (32°F to 113°F)

GIC-XP4L-G

View

Figure2-56 GIC-XP4L-G view

(1) 10GBASE-R/W SFP+ fiber ports (4 in total)

(2) SFP+ port LED. For the LED description, see Table2-248.

LEDs

Table2-248 SFP+ port LED description

LED	Status	Description
10GE SFP+ port LED (LINK/ACT)	Flashing	The SFP+ port is receiving or sending data.
	On	A link is present on the SFP+ port.
	Off	No link is present on the SFP+ port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 10/100/1000 Mbps.

Ports

Table2-249 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
GIC-XP4L-G	4-port 10GBASE-R/W Ethernet optical interface card	LC	4	10/100/1000 Mbps
GIC-XP4L-G	4-port 10GBASE-R/W Ethernet optical interface card	LC	4	10 Gbps

Technical specifications

Table2-250 Technical specifications

Item	Description
Dimensions (H × W × D)	22.3 × 190 × 154 mm (0.88 × 7.48 × 6.06 in)
Weight	1.05 kg (2.31 lb)
Maximum power consumption	23 W
Minimum power consumption	15 W
Operating temperature	0°C to 45°C (32°F to 113°F)

GIC-XP6L-G

View

Figure2-57 GIC-XP6L-G view

(1) 10GBASE-R/W SFP+ fiber ports (6 in total)

(2) SFP+ port LED. For the LED description, see Table2-251.

LEDs

Table2-251 SFP+ port LED description

LED	Status	Description
10GE SFP+ port LED (LINK/ACT)	Flashing	The SFP+ port is receiving or sending data.
	On	A link is present on the SFP+ port.
	Off	No link is present on the SFP+ port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 10/100/1000 Mbps.

Ports

Table2-252 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
GIC-XP6L-G	6-port 10GBASE-R/W Ethernet optical interface card	LC	6	10/100/1000 Mbps
GIC-XP6L-G	6-port 10GBASE-R/W Ethernet optical interface card	LC	6	10 Gbps

Technical specifications

Table2-253 Technical specifications

Item	Description
Dimensions (H × W × D)	22.3 × 190 × 154 mm (0.88 × 7.48 × 6.06 in)
Weight	1.05 kg (2.31 lb)
Maximum power consumption	24 W
Minimum power consumption	15 W
Operating temperature	0°C to 45°C (32°F to 113°F)

GIC-XP12LF

View

Figure2-58 GIC-XP12LF view

(1) 10GBASE-R/W SFP+ fiber ports (12 in total)

(2) SFP+ port LED. For the LED description, see Table2-254.

LEDs

Table2-254 SFP+ port LED description

LED	Status	Description
SFP+ port LED (LINK/ACT)	Flashing	The SFP+ port is receiving or sending data.
	On	A link is present on the SFP+ port.
	Off	No link is present on the SFP+ port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 25 Gbps, and yellow indicates a speed of 10 Gbps or 1000 Mbps.

Ports

Table2-255 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
GIC-XP12LF	12-port 10GBASE-R flexible Ethernet optical interface card	LC	12	1000 Mbps
			12	10 Gbps
			4	25 Gbps

NOTE:

You can change the speed of only ports 1 to 4 to 25 Gbps. When any of these ports operates at 25 Gbps, ports 11 and 12 are unavailable. Follow these restrictions and guidelines when you change the port speed:

· Ports 1 and 7 form a group. After you change port 1 to a 25GE interface, port 7 is unavailable.

· Ports 2 and 8 form a group. After you change port 2 to a 25GE interface, port 8 is unavailable.

· Ports 3 and 9 form a group. After you change port 3 to a 25GE interface, port 9 is unavailable.

· Ports 4 and 10 form a group. After you change port 4 to a 25GE interface, port 10 is unavailable.

· Ports 5 and 6 cannot be changed to 25GE interfaces, and they are not affected by any speed change of other ports.

For more information about the commands used for changing the speed of ports on the subcard, see H3C SR8800-X Routers Command Reference.

Technical specifications

Table2-256 Technical specifications

Item	Description
Dimensions (H × W × D)	22.3 × 190 × 154 mm (0.88 × 7.48 × 6.06 in)
Weight	0.75 kg (1.65 lb)
Maximum power consumption	46 W
Minimum power consumption	24 W
Operating temperature	0°C to 45°C (32°F to 113°F)

GIC-XP12L-G

View

Figure2-59 GIC-XP12L-G view

(1) 10GBASE-R/W SFP+ fiber ports (12 in total)

(2) SFP+ port LED. For the LED description, see Table2-257.

LEDs

Table2-257 SFP+ port LED description

LED	Status	Description
10GE SFP+ port LED (LINK/ACT)	Flashing	The SFP+ port is receiving or sending data.
	On	A link is present on the SFP+ port.
	Off	No link is present on the SFP+ port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 10/100/1000 Mbps.

Ports

Table2-258 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
GIC-XP12L-G	12-port 10GBASE-R/W Ethernet optical interface card	LC	12	10/100/1000 Mbps
GIC-XP12L-G	12-port 10GBASE-R/W Ethernet optical interface card	LC	12	10 Gbps

Technical specifications

Table2-259 Technical specifications

Item	Description
Dimensions (H × W × D)	22.3 × 190 × 154 mm (0.88 × 7.48 × 6.06 in)
Weight	1.05 kg (2.31 lb)
Maximum power consumption	28 W
Minimum power consumption	15 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC subcards

IMPORTANT:

· To use a MIC interface card, you must install it on a CMPE, SPE, or SPEX/CSPEX base card. You cannot install it directly on the router.

· For the compatibility between MIC interface cards and CMPE, SPE, or SPEX/CSPEX base cards, see the compatibility information for the base cards.

· A combo interface is a logical interface that contains an SFP port and an RJ-45 Ethernet port. Only one of them can be activated at a time.

· Some MIC subcards support changing the speed and operating mode. For more information, see H3C SR8800-X Routers Configuration Guides.

MIC-CLP2L

View

Figure2-60 MIC-CLP2L view

(1) CPOS-OC3/STM1-SFP port (2 in total)	(2) Port LED. For the LED description, see Table2-260.

LEDs

Table2-260 WAN port LED description

LED	Status	Description
WAN port LED (ACT/ALM)	Flashing green	The port is up and is receiving or sending data correctly.
	Steady green	The port is up and no services are running on the port.
	Steady red	An alarm has occurred.
	Off	The port is down.

Ports

Table2-261 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-CLP2L	2-port OC-3/STM-1 CPOS optical interface card	LC	2	155 Mbps (OC-3/STM-1)

Technical specifications

Table2-262 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.32 kg (0.71 lb)
Maximum power consumption	10.9 W
Minimum power consumption	9.8 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-CLP4L

View

Figure2-61 MIC-CLP4L view

(1) CPOS-OC3/STM1-SFP port (4 in total)	(2) Port LED. For the LED description, see Table2-263.

LEDs

Table2-263 WAN port LED description

LED	Status	Description
WAN port LED (ACT/ALM)	Flashing green	The port is up and is receiving or sending data correctly.
	Steady green	The port is up and no services are running on the port.
	Steady red	An alarm has occurred.
	Off	The port is down.

Ports

Table2-264 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-CLP4L	4-port OC-3/STM-1 CPOS optical interface card	LC	4	155 Mbps (OC-3/STM-1)

Technical specifications

Table2-265 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.30 kg (0.66 lb)
Maximum power consumption	12.9 W
Minimum power consumption	9.8 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-CP1L

View

Figure2-62 MIC-CP1L view

(1) 100GBASE-R-CFP fiber ports (1 in total)	(2) CFP port LED. For the LED description, see Table2-266

LEDs

Table2-266 CFP port LED description

LED	Status	Description
CFP port LED	Flashing	The CFP port is sending or receiving data.
	Steady on	A link is present on the CFP port.
	Off	No link is present on the CFP port.

Ports

Table2-267 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-CP1L	1-port 100G optical interface card (CFP, LC)	LC	1	100 Gbps

Technical specifications

Table2-268 Technical specifications

Item	Description
Dimensions (H × W × D)	37 mm × 171 mm × 157 mm (1.46 in × 6.73 in × 6.18 in)
Weight	0.55 kg (1.21 lb)
Maximum power consumption	11.8 W
Minimum power consumption	3.3 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-CP1L-V2

View

Figure2-63 MIC-CP1L-V2 view

(1) CFP2 port LED. For the LED description, see Table2-269.	(2) 100GBASE-R-CFP2 fiber ports (1 in total)

LEDs

Table2-269 CFP2 port LED description

LED	Status	Description
CFP2 port LED	Flashing	The CFP2 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the CFP2 port.
	Off	No link is present on the CFP2 port.

Ports

Table2-270 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-CP1L-V2	1-port 100G Ethernet optical interface card (CFP2, LC)	LC	1	100 Gbps

Technical specifications

Table2-271 Technical specifications

Item	Description
Dimensions (H × W × D)	23 mm × 137 mm × 119 mm (0.91 in × 5.39 in × 4.69 in)
Weight	0.45 kg (0.99 lb)
Maximum power consumption	8.7 W
Minimum power consumption	6 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-CP2L

View

Figure2-64 MIC-CP2L view

(1) 100GBASE-R-CFP2 fiber ports (2 in total) (100G CFP2 modules supported)	(2) CFP2 port LED. For the LED description, see Table2-272.

LEDs

Table2-272 CFP2 port LED description

LED	Status	Description
CFP2 port LED	Flashing	The CFP2 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the CFP2 port.
	Off	No link is present on the CFP2 port.

Ports

Table2-273 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-CP2L	2-port 100G Ethernet optical interface card (CFP2, LC)	LC	2	100 Gbps

Technical specifications

Table2-274 Technical specifications

Item	Description
Dimensions (H × W × D)	38 mm × 179 mm × 149 mm (1.50 in × 7.05 in × 5.87 in)
Weight	0.80 kg (1.76 lb)
Maximum power consumption	18.1 W
Minimum power consumption	8.6 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-CP2L-V2

View

Figure2-65 MIC-CP2L-V2 view

(1) QSFP28 port LED. For the LED description, see Table2-275.	(2) 100GBASE-R-QSFP28 fiber ports (2 in total)

LEDs

Table2-275 QSFP28 port LED description

LED	Status	Description
QSFP28 port LED	Flashing	The QSFP28 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the QSFP28 port.
	Off	No link is present on the QSFP28 port.

Ports

Table2-276 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-CP2L-V2	2-port 100G Ethernet optical interface card (QSFP28)	LC	2	100 Gbps

Technical specifications

Table2-277 Technical specifications

Item	Description
Dimensions (H × W × D)	23 mm × 137 mm × 119 mm (0.91 in × 5.39 in × 4.69 in)
Weight	0.40 kg (0.88 lb)
Maximum power consumption	15 W
Minimum power consumption	9.3 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-CQ1L1

View

Figure2-66 MIC-CQ1L1 view

(1) 100GBASE-R-QSFP28 port (1 in total)	(2) QSFP28 port LED. For the LED description, see Table2-278

LEDs

Table2-278 QSFP28 port LED description

LED	Status	Description
QSFP28 port LED	Flashing	The QSFP28 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the QSFP28 port.
	Off	No link is present on the QSFP28 port.

Ports

Table2-279 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-CQ1L1	1-port 100G Ethernet optical interface card	LC	1	100 Gbps
MIC-CQ1L1	1-port 100G Ethernet optical interface card	LC	1	40 Gbps

Technical specifications

Table2-280 Technical specifications

Item	Description
Dimensions (H × W × D)	37 mm × 171 mm × 157 mm (1.46 in × 6.73 in × 6.18 in)
Weight	0.50 kg (1.10 lb)
Maximum power consumption	15 W
Minimum power consumption	9 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-CQ1L2

View

Figure2-67 MIC-CQ1L2 view

(1) QSFP28 port LED. For the LED description, see Table2-281.	(2) 100GBASE-R-QSFP28 fiber ports (1 in total)

LEDs

Table2-281 QSFP28 port LED description

LED	Status	Description
QSFP28 port LED	Flashing	The QSFP28 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the QSFP28 port.
	Off	No link is present on the QSFP28 port.

Ports

Table2-282 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-CQ1L2	1-port 100G Ethernet optical interface card	LC	1	· 100 Gbps
MIC-CQ1L2	1-port 100G Ethernet optical interface card	LC	1	· 40 Gbps

Technical specifications

Table2-283 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.45 kg (0.99 lb)
Maximum power consumption	15 W
Minimum power consumption	9 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-CQ1LF

View

Figure2-68 MIC-CQ1LF view

(1) 100G/50G/40G fiber port LED. For the LED description, see Table2-284.	(2) 100G/50G/40G fiber port (1 in total)
(3) 50G/40G fiber port (1 in total)	(4) 50G/40G fiber port LED. For the LED description, see Table2-284.

LEDs

Table2-284 Fiber port LED description

LED	Status	Description
Fiber port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of a port by observing the color of its LED. Green indicates a speed of 100 Gbps, and yellow indicates a speed of 50 Gbps or 40 Gbps.

Ports

Table2-285 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-CQ1LF	2-port 50G/1-port 100G flexible Ethernet optical interface card (QSFP28,LC)	LC	1	100 Gbps
			2	50 Gbps
			2	40 Gbps

NOTE:

Technical specifications

Table2-286 Technical specifications

Item	Description
Dimensions (H × W × D)	36 × 171 × 157 mm (1.42 × 6.73 × 6.18 in)
Weight	0.58 kg (1.28 lb)
Maximum power consumption	27 W
Minimum power consumption	21 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-CQ2L

View

Figure2-69 MIC-CQ2L view

(1) QSFP28 port LED. For the LED description, see Table2-287.	(2) 100GBASE-R-QSFP28 fiber ports (2 in total)

LEDs

Table2-287 QSFP28 port LED description

LED	Status	Description
QSFP28 port LED	Flashing	The QSFP28 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the QSFP28 port.
	Off	No link is present on the QSFP28 port.

Ports

Table2-288 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-CQ2L	2-port 100G Ethernet optical interface card (QSFP28)	LC	2	100 Gbps
MIC-CQ2L	2-port 100G Ethernet optical interface card (QSFP28)	LC	2	40 Gbps

Technical specifications

Table2-289 Technical specifications

Item	Description
Dimensions (H × W × D)	38 mm × 179 mm × 149 mm (1.50 in × 7.05 in × 5.87 in)
Weight	0.40 kg (0.88 lb)
Maximum power consumption	16 W
Minimum power consumption	8 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-ET16L

View

Figure2-70 MIC-ET16L view

(1) E1-HM96 copper ports (16 in total)	(2) Port LED. For the LED description, see Table2-290.

LED

Table2-290 LED description

LED	Status	Description
ACT/ALM	Flashing green	The port is sending or receiving data.
	Steady green	A link is present, but the port is not receiving or sending data.
	Steady red	An alarm has occurred.
	Off	No link is present on the port.

Ports

Table2-291 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-ET16L	16-port E1 electrical interface card (HM96 male connector)	HM96 male	16	E1

Technical specifications

Table2-292 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.30 kg (0.66 lb)
Maximum power consumption	8.7W
Minimum power consumption	8.6 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-GP10L1/MIC-GP10L2

View

Figure2-71 MIC-GP10L1 view

(1) 1000BASE-X-SFP fiber ports (10 in total)	(2) SFP port LED. For the LED description, see Table2-293.

The views of the MIC-GP10L1 and MIC-GP10L2 are similar. This figure uses the MIC-GP10L1 as an example.

LEDs

Table2-293 GE SFP port LED description

LED	Status	Description
GE SFP port LED (LINK/ACT)	Flashing green	The SFP port is sending or receiving data.
	Green	A link is present on the SFP port.
	Off	No link is present on the SFP port.

Ports

Table2-294 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-GP10L1	10-port 1000BASE-X optical interface card (SFP, LC)	LC	10	100 Mbps
MIC-GP10L1	10-port 1000BASE-X optical interface card (SFP, LC)	LC	10	1000 Mbps
MIC-GP10L2	10-port 1000BASE-X Ethernet optical interface card (SFP, LC)	LC	10	100 Mbps
MIC-GP10L2		LC	10	1000 Mbps

Technical specifications

Table2-295 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	· MIC-GP10L1: 0.30 kg (0.66 lb) · MIC-GP10L2: 0.48 kg (1.06 lb)
Maximum power consumption	· MIC-GP10L1: 7.9 W · MIC-GP10L2: 30 W
Minimum power consumption	· MIC-GP10L1: 2.1 W · MIC-GP10L2: 20 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-GP10L-V2

View

Figure2-72 MIC-GP10L-V2 view

(1) 1000BASE-X-SFP fiber ports (10 in total)	(2) SFP port LED. For the LED description, see Table2-296.

LEDs

Table2-296 GE SFP port LED description

LED	Status	Description
GE SFP port LED (LINK/ACT)	Flashing green	The SFP port is sending or receiving data.
	Green	A link is present on the SFP port.
	Off	No link is present on the SFP port.

Ports

Table2-297 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-GP10L-V2	10-port 1000BASE-X Ethernet optical interface card (SFP, LC)	LC	10	100 Mbps
MIC-GP10L-V2		LC	10	1000 Mbps

Technical specifications

Table2-298 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.35 kg (0.77 lb)
Maximum power consumption	9.4 W
Minimum power consumption	9.3 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-GP20L

View

Figure2-73 MIC-GP20L view

(1) 1000BASE-X-SFP fiber ports (20 in total)	(2) SFP port LED. For the LED description, see Table2-299.

LEDs

Table2-299 GE SFP port LED description

LED	Status	Description
GE SFP port LED (LINK/ACT)	Flashing green	The SFP port is sending or receiving data.
	Steady green	A link is present on the SFP port.
	Off	No link is present on the SFP port.

Ports

Table2-300 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-GP20L	20-port 1000BASE-X Ethernet optical interface card (SFP, LC)	LC	20	100 Mbps
MIC-GP20L		LC	20	1000 Mbps

Technical specifications

Table2-301 Technical specifications

Item	Description
Dimensions (H × W × D)	37 mm × 171 mm × 157 mm (1.46 in × 6.73 in × 6.18 in)
Weight	0.55 kg (1.21 lb)
Maximum power consumption	23 W
Minimum power consumption	7.6 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-GP20L1

View

Figure2-74 MIC-GP20L1 view

(1) 1000BASE-X-SFP fiber ports (20 in total)	(2) SFP port LED. For the LED description, see Table2-302.

LEDs

Table2-302 GE SFP port LED description

LED	Status	Description
GE SFP port LED (LINK/ACT)	Flashing green	The SFP port is sending or receiving data.
	Green	A link is present on the SFP port.
	Off	No link is present on the SFP port.

Ports

Table2-303 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-GP20L1	20-port 1000BASE-X Ethernet optical interface card (SFP, LC)	LC	20	100 Mbps
MIC-GP20L1		LC	20	1000 Mbps

Technical specifications

Table2-304 Technical specifications

Item	Description
Dimensions (H × W × D)	38 mm × 179 mm × 149 mm (1.50 in × 7.05 in × 5.87 in)
Weight	0.80 kg (1.76 lb)
Maximum power consumption	18 W
Minimum power consumption	7 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-GP4L

View

Table2-305 MIC-GP4L view

(1) Combo interfaces (4 in total)	(2) Combo fiber port LINK/ACT LED. For the LED description, see Table2-306.
(3) Combo copper LINK LED. For the LED description, see Table2-306.	(4) Combo copper ACT LED. For the LED description, see Table2-306.

LEDs

Table2-306 Combo ports LED description

Port type	LED	Status	Description
Combo fiber port	LINK/ACT	Steady on	The port is up.
		Flashing green	The port is receiving or sending data correctly.
		Off	The port is down.
Combo copper port	LINK (Green)	Steady on	The port is up.
	LINK (Green)	Off	The port is down.
	ACT (Orange)	Flashing green	The port is receiving or sending data correctly.
	ACT (Orange)	Off	The port is not receiving or sending data.

Ports

Table2-307 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-GP4L	4-port 1000BASE-X/1000BASE-T combo interface card	RJ45	4	10/100/1000 Mbps
		LC	4	100 Mbps
		LC	4	1000 Mbps

Technical specifications

Table2-308 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.31 kg (0.68 lb)
Maximum power consumption	5.5 W
Minimum power consumption	0.8 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-GP8L

View

Figure2-75 MIC-GP8L view

(1) 1000BASE-X-SFP fiber ports (8 in total)	(2) SFP port LED. For the LED description, see Table2-309.

LEDs

Table2-309 GE SFP port LED description

LED	Status	Description
GE SFP port LED (LINK/ACT)	Flashing green	The SFP port is sending or receiving data.
	Green	A link is present on the SFP port.
	Off	No link is present on the SFP port.

Ports

Table2-310 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-GP8L	8-port 1000BASE-X optical interface card (SFP, LC)	LC	8	100 Mbps
MIC-GP8L	8-port 1000BASE-X optical interface card (SFP, LC)	LC	8	1000 Mbps

Technical specifications

Table2-311 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.29 kg (0.64 lb)
Maximum power consumption	4.7 W
Minimum power consumption	0.6 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-GT20L/MIC-GT20L1

View

Figure2-76 MIC-GT20L view

(1) 10/100/1000BASE-T copper ports (20 in total)	(2) RJ45 Ethernet port LED. For the description for the RJ45 port LEDs on the MIC-GT20L, see Table2-312. For the description for the RJ45 port LEDs on the MIC-GT20L1, see Table2-313.

The views of the MIC-GT20L and MIC-GT20L1 are similar. This figure uses the MIC-GT20L as an example.

LEDs

Table2-312 RJ45 Ethernet port LED description (1)

LED	Status	Description
RJ-45 Ethernet port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Table2-313 RJ45 Ethernet port LED description (2)

LED	Status	Description
RJ-45 Ethernet port LED	LINK: Steady green	A 1000 Mbps link is present on the port.
	LINK: Flashing green	The port is receiving or sending data at 1000 Mbps.
	ACT: Steady yellow	A 10/100 Mbps link is present on the port.
	ACT: Flashing yellow	The port is receiving or sending data at 10/100 Mbps.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an RJ-45 Ethernet port by observing the color of its LEDs. A green LINK LED indicates a speed of 1000 Mbps, and a yellow ACT LED indicates a speed of 10/100 Mbps.

Ports

Table2-314 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-GT20L	20-port 1000BASE-X Ethernet electrical interface card (RJ45)	RJ45	20	10/100/1000 Mbps
MIC-GT20L1	20-port 1000BASE-T Ethernet copper interface card (RJ45)	RJ45	20	10/100/1000 Mbps

Technical specifications

Table2-315 Technical specifications

Item	Description
Dimensions (H × W × D)	37 mm × 171 mm × 157 mm (1.46 in × 6.73 in × 6.18 in)
Weight	· MIC-GT20L: 0.50 kg (1.10 lb) · MIC-GT20L1: 0.40 kg (0.88 lb)
Maximum power consumption	· MIC-GT20L: 11.9 W · MIC-GT20L1: 39 W
Minimum power consumption	· MIC-GT20L: 9.2 W · MIC-GT20L1: 28 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-PSP4L

View

Figure2-77 MIC-PSP4L view

(1) OC-48c/STM-16c POS fiber ports (4 in total)	(2) Port LED. For the LED description, see Table2-316.

LEDs

Table2-316 WAN port LED description

LED	Status	Description
WAN port LED (ACT/ALM)	Flashing green	The port is up and is receiving or sending data correctly.
	Steady green	The port is up and no services are running on the port.
	Steady red	An alarm has occurred.
	Off	The port is down.

Ports

Table2-317 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-PSP4L	4-port OC-48c/STM-16c POS optical interface card (SFP, LC)	LC	4	2.5 Gbps

Technical specifications

Table2-318 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.40 kg (0.88 lb)
Maximum power consumption	33 W
Minimum power consumption	29 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-QP1L

View

Figure2-78 MIC-QP1L view

(1) 40GBASE-R-QSFP+ fiber port (1 in total)	(2) QSFP+ port LED. For the LED description, see Table2-319.

LEDs

Table2-319 QSFP + port LED description

LED	Status	Description
QSFP + port LED	Flashing	The QSFP+ port is sending or receiving data.
	Steady on	A link is present on the QSFP+ port.
	Off	No link is present on the QSFP+ port.

Ports

Table2-320 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-QP1L	1-port 40G Ethernet optical interface card (QSFP+, LC)	LC	1	40 Gbps
MIC-QP1L	1-port 40G Ethernet optical interface card (QSFP+, LC)	LC	4 (after splitting)	10 Gbps

NOTE:

You can execute a command to split the 40G port into four 10G breakout interfaces. For more information about the command, see H3C SR8800-X Routers Command Reference.

Technical specifications

Table2-321 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.35 kg (0.77 lb)
Maximum power consumption	7 W
Minimum power consumption	3 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-SP4L

View

Figure2-79 MIC-SP4L view

(1) OC-3c/STM-1c POS/ATM fiber ports (4 in total) or OC-12c/STM-4c POS/ATM fiber port (port 1)	(2) Port LED. For the LED description, see Table2-322.

LEDs

Table2-322 WAN port LED description

LED	Status	Description
WAN port LED (ACT/ALM)	Flashing green	The port is up and is receiving or sending data correctly.
	Steady green	The port is up and no services are running on the port.
	Steady red	An alarm has occurred.
	Off	The port is down.

Ports

Table2-323 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-SP4L	4-port OC-3c/STM-1c POS/ATM or 1-port OC-12c/STM-4c POS/ATM optical interface card (SFP, LC)	LC	4	155 Mbps (OC-3/STM-1)
MIC-SP4L		LC	1	622 Mbps (OC-12/STM-4)

NOTE:

Technical specifications

Table2-324 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.30 kg (0.66 lb)
Maximum power consumption	13.5 W
Minimum power consumption	9.6 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-SP8L

View

Figure2-80 MIC-SP8L view

(1) OC-3c/STM-1c POS fiber ports (8 in total)	(2) Port LED. For the LED description, see Table2-325.

LEDs

Table2-325 WAN port LED description

LED	Status	Description
WAN port LED (ACT/ALM)	Flashing green	The port is up and is receiving or sending data correctly.
	Steady green	The port is up and no services are running on the port.
	Steady red	An alarm has occurred.
	Off	The port is down.

Ports

Table2-326 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-SP8L	8-port OC-3c/STM-1c POS optical interface card (SFP, LC)	LC	8	155 Mbps (OC-3/STM-1)

Technical specifications

Table2-327 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.30 kg (0.66 lb)
Maximum power consumption	16.3 W
Minimum power consumption	14 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-TCP8L

View

Figure2-81 MIC-TCP8L view

(1) OC-3c/OC-12c POS/GE fiber ports (8 in total)	(2) Port LED. For the LED description, see Table2-328.

LEDs

Table2-328 WAN port LED description

LED	Status	Description
WAN port LED (ACT/ALM)	Flashing green	The port is up and is receiving or sending data correctly.
	Steady green	The port is up and no services are running on the port.
	Steady red	An alarm has occurred.
	Off	The port is down.

Ports

Table2-329 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-TCP8L	8-port OC-3c/OC-12c POS/GE optical interface card (SFP, LC)	LC	8	100 Mbps
				155 Mbps (OC-3/STM-1)
				622 Mbps (OC-12/STM-4)
				1000 Mbps

Technical specifications

Table2-330 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.40 kg (0.88 lb)
Maximum power consumption	30 W
Minimum power consumption	28 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-XP10LF

View

Figure2-82 MIC-XP10LF view

(1) Port LED. For the LED description, see Table2-331.	(2) 25GBASE-R-SFP28 fiber ports (ports 1 to 4) or 10GBASE-R-SFP+ fiber ports

LEDs

Table2-331 Port LED description

LED	Status	Description
Port LED	Flashing	The port is receiving or sending data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP28 port by observing the color of its LED. Green indicates a speed of 25 Gbps, and yellow indicates a speed of 10 Gbps or 1000 Mbps.

Ports

Table2-332 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-XP10LF	10-port 10GBASE-R flexible Ethernet optical interface card (SFP+,LC)	LC	10	1000 Mbps
			10	10 Gbps
			4	25 Gbps

NOTE:

You can change the speed of only ports 1 to 4 to 25 Gbps. Follow these restrictions and guidelines when you change the port speed:

· Ports 1 and 7 form a group. After you change port 1 to a 25GE interface, port 7 is unavailable.

· Ports 2 and 8 form a group. After you change port 2 to a 25GE interface, port 8 is unavailable.

· Ports 3 and 9 form a group. After you change port 3 to a 25GE interface, port 9 is unavailable.

· Ports 4 and 10 form a group. After you change port 4 to a 25GE interface, port 10 is unavailable.

· Ports 5 and 6 cannot be changed to 25GE interfaces, and they are not affected by any speed change of other ports.

For more information about the commands used for changing the speed of ports on the subcard, see H3C SR8800-X Routers Command Reference.

Technical specifications

Table2-333 Technical specifications

Item	Description
Dimensions (H × W × D)	36 × 171 × 157 mm (1.42 × 6.73 × 6.18 in)
Weight	0.61 kg (1.34 lb)
Maximum power consumption	37 W
Minimum power consumption	30 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-XP10L-LAN

View

Figure2-83 MIC-XP10L-LAN view

(1) 10GBASE-R-SFP+ fiber ports or 1000BASE-X-SFP fiber ports (10 in total)	(2) SFP+ port LED. For the LED description, see Table2-334.

LEDs

Table2-334 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 1000 Mbps.

Ports

Table2-335 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-XP10L-LAN	10-port 10GBASE-R Ethernet optical interface card (SFP+, LC)-LAN	LC	10	10 Gbps
MIC-XP10L-LAN		LC	10	1000 Mbps

Technical specifications

Table2-336 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.46 kg (1.01 lb)
Maximum power consumption	20 W
Minimum power consumption	12 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-XP20L

View

Figure2-84 MIC-XP20L view

(1) 10GBASE-R/W-SFP+ fiber ports (20 in total) (10GE SFP+ modules supported)	(2) SFP+ port LED. For the LED description, see Table2-337.

LEDs

Table2-337 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 100/1000 Mbps.

Ports

Table2-338 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-XP20L	20-port 10GBASE-R/W Ethernet optical interface card (SFP+, LC)	LC	20	100 Mbps
				1000 Mbps
				10 Gbps

Technical specifications

Table2-339 Technical specifications

Item	Description
Dimensions (H × W × D)	38 mm × 179 mm × 149 mm (1.50 in × 7.05 in × 5.87 in)
Weight	0.95 kg (2.09 lb)
Maximum power consumption	53 W
Minimum power consumption	38.3 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-XP2L

View

Figure2-85 MIC-XP2L view

(1) 10GBASE-R/W-SFP+ fiber ports (2 in total)	(2) SFP+ port LED. For the LED description, see Table2-340.

LEDs

Table2-340 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 100/1000 Mbps.

Ports

Table2-341 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-XP2L	2-port 10GBASE-R Ethernet optical interface card (SFP+, LC)	LC	2	100 Mbps
				1000 Mbps
				10 Gbps

Technical specifications

Table2-342 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.29 kg (0.64 lb)
Maximum power consumption	13 W
Minimum power consumption	10 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-XP2L-LAN

View

Figure2-86 MIC-XP2L-LAN view

(1) 10GBASE-R-SFP+ fiber ports (2 in total)	(2) SFP+ port LED. For the LED description, see Table2-343.

LEDs

Table2-343 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 100/1000 Mbps.

Ports

Table2-344 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-XP2L-LAN	2-port 10GBASE-R Ethernet optical interface card (SFP+, LC)-LAN	LC	2	100 Mbps
				1000 Mbps
				10 Gbps

Technical specifications

Table2-345 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.28 kg (0.62 lb)
Maximum power consumption	9 W
Minimum power consumption	6 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-XP4L1

View

Figure2-87 MIC-XP4L1 view

(1) 10GBASE-R/W-SFP+ fiber ports (4 in total)	(2) SFP+ port LED. For the LED description, see Table2-346.

LEDs

Table2-346 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 100/1000 Mbps.

Ports

Table2-347 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-XP4L1	4-port 10GBASE-R/W Ethernet optical interface card 1 (SFP+, LC)	LC	4	100 Mbps
				1000 Mbps
				10 Gbps

Technical specifications

Table2-348 MIC-XP4L1

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.30 kg (0.66 lb)
Maximum power consumption	13 W
Minimum power consumption	11 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-XP5L

View

Figure2-88 MIC-XP5L view

(1) 10GBASE-R/W-SFP+ fiber ports (5 in total)	(2) SFP+ port LED. For the LED description, see Table2-349.

LEDs

Table2-349 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 100/1000 Mbps.

Ports

Table2-350 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-XP5L	5-port 10GBASE-R/W Ethernet optical interface card (SFP+, LC)	LC	5	100 Mbps
				1000 Mbps
				10 Gbps

Technical specifications

Table2-351 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.30 kg (0.66 lb)
Maximum power consumption	14.2 W
Minimum power consumption	10.4 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-XP5L1/MIC-XP5L2

View

Figure2-89 MIC-XP5L1 view

(1) 10GBASE-R/W-SFP+ fiber ports (5 in total)	(2) SFP+ port LED. For the LED description, see Table2-352.

The views of the MIC-XP5L1 and MIC-XP5L2 are similar. This figure uses the MIC-XP5L1 as an example.

LEDs

Table2-352 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 100/1000 Mbps.

Ports

Table2-353 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-XP5L1	5-port 10GBASE-R/W Ethernet optical interface card	LC	5	100 Mbps
				1000 Mbps
				10 Gbps
MIC-XP5L2	5-port 10GBASE-R Ethernet optical interface card	LC	5	100 Mbps
				1000 Mbps
				10 Gbps

Technical specifications

Table2-354 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.35 kg (0.77 lb)
Maximum power consumption	· MIC-XP5L1: 13 W · MIC-XP5L2: 6.4 W
Minimum power consumption	· MIC-XP5L1: 11 W · MIC-XP5L2: 2.3 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-XP8L

View

Figure2-90 MIC-XP8L view

(1) 10GBASE-R/W-SFP+ fiber ports (8 in total)	(2) SFP+ port LED. For the LED description, see Table2-355.

LEDs

Table2-355 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 1000 Mbps.

Ports

Table2-356 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-XP8L	8-port 10GBASE-R/W Ethernet optical interface card (SFP+, LC)	LC	8	10 Gbps
MIC-XP8L		LC	8	1000 Mbps

Technical specifications

Table2-357 Technical specifications

Item	Description
Dimensions (H × W × D)	38 mm × 179 mm × 149 mm (1.50 in × 7.05 in × 5.87 in)
Weight	0.70 kg (1.54 lb)
Maximum power consumption	22 W
Minimum power consumption	16 W
Operating temperature	0°C to 45°C (32°F to 113°F)

NIC subcards

IMPORTANT:

· To use a NIC interface card, you must install it on a CMPE, SPE, or SPEX/CSPEX base card. You cannot install it directly on the router.

· For the compatibility between NIC interface cards and CMPE, SPE, or SPEX/CSPEX base cards, see the compatibility information for the base cards.

· Some NIC subcards support changing the speed and operating mode. For more information, see H3C SR8800-X Routers Configuration Guides.

NIC-CC1L

View

Figure2-91 NIC-CC1L view

(1) 100GBASE-R-CFP2 fiber ports (1 in total)	(2) CFP2 port LED. For the LED description, see Table2-358.

LEDs

Table2-358 CFP2 port LED description

LED	Status	Description
CFP2 port LED	Flashing	The CFP2 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the CFP2 port.
	Off	No link is present on the CFP2 port.

Ports

Table2-359 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
NIC-CC1L	1-port 100G Ethernet optical interface card	LC	1	100 Gbps

Technical specifications

Table2-360 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.60 kg (1.32 lb)
Maximum power consumption	9.7 W
Minimum power consumption	9.6 W
Operating temperature	0°C to 45°C (32°F to 113°F)

NIC-CC2L

View

Figure2-92 NIC-CC2L view

(1) 100GBASE-R-CFP2 fiber ports (2 in total)	(2) CFP2 port LED. For the LED description, see Table2-361.

LEDs

Table2-361 CFP2 port LED description

LED	Status	Description
CFP2 port LED	Flashing	The CFP2 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the CFP2 port.
	Off	No link is present on the CFP2 port.

Ports

Table2-362 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
NIC-CC2L	2-port 100G Ethernet optical interface card	LC	2	100 Gbps

Technical specifications

Table2-363 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.85 kg (1.87 lb)
Maximum power consumption	21 W
Minimum power consumption	19.2 W
Operating temperature	0°C to 45°C (32°F to 113°F)

NIC-CQ1L

View

Figure2-93 NIC-CQ1L view

(1) 100GBASE-R-QSFP28 fiber ports (1 in total)	(2) QSFP28 port LED. For the LED description, see Table2-364.

LEDs

Table2-364 QSFP28 port LED description

LED	Status	Description
QSFP28 port LED	Flashing	The QSFP28 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the QSFP28 port.
	Off	No link is present on the QSFP28 port.

Ports

Table2-365 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
NIC-CQ1L	1-port 100G Ethernet optical interface card	LC	1	100 Gbps

Technical specifications

Table2-366 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.35 kg (0.77 lb)
Maximum power consumption	13 W
Minimum power consumption	8 W
Operating temperature	0°C to 45°C (32°F to 113°F)

NIC-CQ2L/NIC-CQ2LB

View

Figure2-94 NIC-CQ2L view

(1) 100GBASE-R-QSFP28 fiber ports (2 in total)	(2) QSFP28 port LED. For the LED description, see Table2-367.

The views of NIC-CQ2L and NIC-CQ2LB are similar. This figure uses the NIC-CQ2L as an example.

LEDs

Table2-367 QSFP28 port LED description

LED	Status	Description
QSFP28 port LED	Flashing	The QSFP28 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the QSFP28 port.
	Off	No link is present on the QSFP28 port.

Ports

Table2-368 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
NIC-CQ2L	2-port 100G Ethernet optical interface card	LC	2	100 Gbps
NIC-CQ2LB	2-port 100G Ethernet optical interface card B	LC	2	100 Gbps

Technical specifications

Table2-369 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	· NIC-CQ2L: 0.35 kg (0.77 lb) · NIC-CQ2LB: 0.75 kg (1.65 lb)
Maximum power consumption	26 W
Minimum power consumption	16 W
Operating temperature	0°C to 45°C (32°F to 113°F)

NIC-GP20L

View

Figure2-95 NIC-GP20L view

(1) 1000BASE-X-SFP fiber ports (20 in total)	(2) SFP port LED. For the LED description, see Table2-370.

LEDs

Table2-370 GE SFP port LED description

LED	Status	Description
GE SFP port LED (LINK/ACT)	Flashing green	The SFP port is sending or receiving data.
	Green	A link is present on the SFP port.
	Off	No link is present on the SFP port.

Ports

Table2-371 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
NIC-GP20L	20-port 1000BASE-X Ethernet optical interface card	LC	20	100 Mbps
NIC-GP20L	20-port 1000BASE-X Ethernet optical interface card	LC	20	1000 Mbps

Technical specifications

Table2-372 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.65 kg (1.43 lb)
Maximum power consumption	13.8 W
Minimum power consumption	12 W
Operating temperature	0°C to 45°C (32°F to 113°F)

NIC-GP24L

View

Figure2-96 NIC-GP24L view

(1) 1000BASE-X-SFP fiber ports (24 in total)	(2) SFP port LED. For the LED description, see Table2-373.

LEDs

Table2-373 GE SFP port LED description

LED	Status	Description
GE SFP port LED (LINK/ACT)	Flashing green	The SFP port is sending or receiving data.
	Green	A link is present on the SFP port.
	Off	No link is present on the SFP port.

Ports

Table2-374 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
NIC-GP24L	24-port 1000BASE-X Ethernet optical interface card	LC	24	100 Mbps
NIC-GP24L	24-port 1000BASE-X Ethernet optical interface card	LC	24	1000 Mbps

Technical specifications

Table2-375 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.50 kg (1.10 lb)
Maximum power consumption	28 W
Minimum power consumption	20 W
Operating temperature	0°C to 45°C (32°F to 113°F)

NIC-GP24L1/NIC-GP24L1B

View

Figure2-97 NIC-GP24L1 view

(1) 1000BASE-X-SFP fiber ports (24 in total)	(2) SFP port LED. For the LED description, see Table2-376.

The views of the NIC-GP24L1 and NIC-GP24L1B are similar. This figure uses the NIC-GP24L1 as an example.

LEDs

Table2-376 GE SFP port LED description

LED	Status	Description
GE SFP port LED (LINK/ACT)	Flashing green	The SFP port is sending or receiving data.
	Green	A link is present on the SFP port.
	Off	No link is present on the SFP port.

Ports

Table2-377 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
NIC-GP24L1	24-port 1000BASE-X Ethernet optical interface card	LC	24	100 Mbps
NIC-GP24L1	24-port 1000BASE-X Ethernet optical interface card	LC	24	1000 Mbps
NIC-GP24L1B	24-port 1000BASE-X Ethernet optical interface card B	LC	24	1000 Mbps

Technical specifications

Table2-378 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	1.00 kg (2.20 lb)
Maximum power consumption	47 W
Minimum power consumption	41 W
Operating temperature	0°C to 45°C (32°F to 113°F)

NIC-GT20L

View

Figure2-98 NIC-GT20L view

(1) 10/100/1000BASE-T copper ports (20 in total)	(2) RJ-45 Ethernet port LED. For the LED description, see Table2-379.

LEDs

Table2-379 RJ-45 Ethernet port LED description

LED	Status	Description
RJ-45 Ethernet port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Ports

Table2-380 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
NIC-GT20L	20-port 1000BASE-T Ethernet copper interface card	RJ45	20	10/100/1000 Mbps

Technical specifications

Table2-381 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.75 kg (1.65 lb)
Maximum power consumption	16.5 W
Minimum power consumption	14.6 W
Operating temperature	0°C to 45°C (32°F to 113°F)

NIC-QP3L

View

Figure2-99 NIC-QP3L view

(1) 40GBASE-R-QSFP+ fiber ports (3 in total)	(2) QSFP+ port LED. For the LED description, see Table2-382.

LEDs

Table2-382 QSFP+ port LED description

LED	Status	Description
QSFP+ port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

Ports

Table2-383 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
NIC-QP3L	3-port 40G Ethernet optical interface card (QSFP+,LC)	LC	3	40 Gbps

Technical specifications

Table2-384 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 × 179 × 118 mm (1.87 × 7.05 × 4.65 in)
Weight	0.75 kg (1.65 lb)
Maximum power consumption	34 W
Minimum power consumption	33 W
Operating temperature	0°C to 45°C (32°F to 113°F)

NIC-XP10L

View

Figure2-100 NIC-XP10L view

(1) 10GBASE-R/W-SFP+ fiber ports (10 in total)	(2) SFP+ port LED. For the LED description, see Table2-385.

LEDs

Table2-385 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 1000 Mbps.

Ports

Table2-386 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
NIC-XP10L	10-port 10GBASE-R/W Ethernet optical interface card	LC	10	10 Gbps
NIC-XP10L	10-port 10GBASE-R/W Ethernet optical interface card	LC	10	1000 Mbps

Technical specifications

Table2-387 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.65 kg (1.43 lb)
Maximum power consumption	27.4 W
Minimum power consumption	26.9 W
Operating temperature	0°C to 45°C (32°F to 113°F)

NIC-XP20L

View

Figure2-101 NIC-XP20L view

(1) 10GBASE-R/W-SFP+ fiber ports (20 in total)	(2) SFP+ port LED. For the LED description, see Table2-388.

LEDs

Table2-388 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 1000 Mbps.

Ports

Table2-389 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
NIC-XP20L	20-port 10GBASE-R/W Ethernet optical interface card	LC	20	10 Gbps
NIC-XP20L	20-port 10GBASE-R/W Ethernet optical interface card	LC	20	1000 Mbps

Technical specifications

Table2-390 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.90 kg (1.98 lb)
Maximum power consumption	58 W
Minimum power consumption	39 W
Operating temperature	0°C to 45°C (32°F to 113°F)

NIC-XP20L1/NIC-XP20L1B

View

Figure2-102 NIC-XP20L1 view

(1) 10GBASE-R/W-SFP+ fiber ports or 1000BASE-X-SFP fiber ports (20 in total)	(2) SFP+ port/SFP port LED. For the SFP+ port LED description, see Table2-391. For the SFP port LED description, see Table2-392

The views of the NIC-XP20L1 and NIC-XP20L1B are similar. This figure uses the NIC-XP20L1 as an example.

LEDs

Table2-391 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 1000 Mbps.

Table2-392 GE SFP port LED description

LED	Status	Description
GE SFP port LED (LINK/ACT)	Flashing green	The SFP port is sending or receiving data.
	Green	A link is present on the SFP port.
	Off	No link is present on the SFP port.

Ports

Table2-393 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
NIC-XP20L1	20-port 10GBASE-R/W Ethernet optical interface card	LC	20	10 Gbps
NIC-XP20L1	20-port 10GBASE-R/W Ethernet optical interface card	LC	20	1000 Mbps
NIC-XP20L1B	20-port 10GBASE-R/W Ethernet optical interface card B	LC	20	10 Gbps
NIC-XP20L1B	20-port 10GBASE-R/W Ethernet optical interface card B	LC	20	1000 Mbps

Technical specifications

Table2-394 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	· NIC-XP20L1: 1.00 kg (2.20 lb) · NIC-XP20L1B: 0.90 kg (1.98 lb)
Maximum power consumption	60 W
Minimum power consumption	50 W
Operating temperature	0°C to 45°C (32°F to 113°F)

NIC-XP5L

View

Figure2-103 NIC-XP5L view

(1) 10GBASE-R/W-SFP+ fiber ports (5 in total)	(2) SFP+ port LED. For the LED description, see Table2-395.

LEDs

Table2-395 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 100/1000 Mbps.

Ports

Table2-396 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
NIC-XP5L	5-port 10GBASE-R/W Ethernet optical interface card	LC	5	100 Mbps
				1000 Mbps
				10 Gbps

Technical specifications

Table2-397 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.60 kg (1.32 lb)
Maximum power consumption	14.9 W
Minimum power consumption	11 W
Operating temperature	0°C to 45°C (32°F to 113°F)

RX-NIC-CC1L

View

Figure2-104 RX-NIC-CC1L view

(1) 100GBASE-R-CFP2 fiber ports (1 in total)	(2) CFP2 port LED. For the LED description, see Table2-398.

LEDs

Table2-398 CFP2 port LED description

LED	Status	Description
CFP2 port LED	Flashing	The CFP2 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the CFP2 port.
	Off	No link is present on the CFP2 port.

Ports

Table2-399 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
RX-NIC-CC1L	1-port 100G Ethernet optical interface card	LC	1	100 Gbps

Technical specifications

Table2-400 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.60 kg (1.32 lb)
Maximum power consumption	9.7 W
Minimum power consumption	9.6 W
Operating temperature	0°C to 45°C (32°F to 113°F)

RX-NIC-CC2L

View

Figure2-105 RX-NIC-CC2L view

(1) 100GBASE-R-CFP2 fiber ports (2 in total)	(2) CFP2 port LED. For the LED description, see Table2-401.

LEDs

Table2-401 CFP2 port LED description

LED	Status	Description
CFP2 port LED	Flashing	The CFP2 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the CFP2 port.
	Off	No link is present on the CFP2 port.

Ports

Table2-402 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
RX-NIC-CC2L	2-port 100G Ethernet optical interface card	LC	2	100 Gbps

Technical specifications

Table2-403 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.85 kg (1.87 lb)
Maximum power consumption	21 W
Minimum power consumption	19.2 W
Operating temperature	0°C to 45°C (32°F to 113°F)

RX-NIC-CQ1LF

View

Figure2-106 RX-NIC-CQ1LF view

(1) 100GBASE-R-QSFP28 port (1 in total)	(2) QSFP28 port LED. For the description, see Table2-404.

LEDs

Table2-404 QSFP28 port LED description

LED	Status	Description
QSFP28 port LED	Flashing	The QSFP28 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the QSFP28 port.
	Off	No link is present on the QSFP28 port.

NOTE:

You can identify the speed of a QSFP28 port by observing the color of its LED. Green indicates a speed of 100 Gbps, and yellow indicates a speed of 50 Mbps.

Ports

Table2-405 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
RX-NIC-CQ1LF	1-port 100G flexible Ethernet optical interface card	LC	1	100 Gbps
RX-NIC-CQ1LF	1-port 100G flexible Ethernet optical interface card	LC	1	50 Gbps

Technical specifications

Table2-406 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.85 kg (1.87 lb)
Maximum power consumption	53 W
Minimum power consumption	35 W
Operating temperature	0°C to 45°C (32°F to 113°F)

RX-NIC-CQ2LF

View

Figure2-107 RX-NIC-CQ1LF view

(1) 100GBASE-R-QSFP28 fiber ports (2 in total).	(2) QSFP28 port LED. For the description, see Table2-407.

LEDs

Table2-407 QSFP28 port LED description

LED	Status	Description
QSFP28 port LED	Flashing	The QSFP28 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the QSFP28 port.
	Off	No link is present on the QSFP28 port.

NOTE:

You can identify the speed of a QSFP28 port by observing the color of its LED. Green indicates a speed of 100 Gbps, and yellow indicates a speed of 50 Mbps.

Ports

Table2-408 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
RX-NIC-CQ2LF	2-port 100G flexible Ethernet optical interface card	LC	2	100 Gbps
RX-NIC-CQ2LF	2-port 100G flexible Ethernet optical interface card	LC	2	50 Gbps

Technical specifications

Table2-409 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	1.00 kg (2.20 lb)
Maximum power consumption	61 W
Minimum power consumption	38 W
Operating temperature	0°C to 45°C (32°F to 113°F)

RX-NIC-GP20L

View

Figure2-108 RX-NIC-GP20L view

(1) 1000BASE-X-SFP fiber ports (20 in total)	(2) SFP port LED. For the LED description, see Table2-410.

LEDs

Table2-410 GE SFP port LED description

LED	Status	Description
GE SFP port LED (LINK/ACT)	Flashing green	The SFP port is sending or receiving data.
	Green	A link is present on the SFP port.
	Off	No link is present on the SFP port.

Ports

Table2-411 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
RX-NIC-GP20L	20-port 1000BASE-X Ethernet optical interface card	LC	20	100 Mbps
RX-NIC-GP20L	20-port 1000BASE-X Ethernet optical interface card	LC	20	1000 Mbps

Technical specifications

Table2-412 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.65 kg (1.43 lb)
Maximum power consumption	13.8 W
Minimum power consumption	12 W
Operating temperature	0°C to 45°C (32°F to 113°F)

RX-NIC-LGQ2L

View

Figure2-109 RX-NIC-LGQ2L view

(1) 50GBASE-R-QSFP28 fiber ports (2 in total)	(2) QSFP28 port LED. For the LED description, see Table2-413.

LEDs

Table2-413 QSFP28 port LED description

LED	Status	Description
QSFP28 port LEDs	Flashing	The QSFP28 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the QSFP28 port.
	Off	No link is present on the QSFP28 port.

Ports

Table2-414 Port specifications

Card model

Description

Connector type

Port quantity

Port transmission speed

RX-NIC-LGQ2L

2-port 50G Ethernet optical interface card

Standard Ethernet mode: 50 Gbps

Flexible Ethernet mode: 50 Gbps

Technical specifications

Table2-415 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.85 kg (1.87 lb)
Maximum power consumption	61 W
Minimum power consumption	38 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

RX-NIC-LGQ4L

View

Figure2-110 RX-NIC-LGQ4L view

(1) 50GBASE-R-QSFP28 fiber ports (4 in total)	(2) QSFP28 port LED. For the description, see Table2-416.

LEDs

Table2-416 QSFP28 port LED description

LED	Status	Description
QSFP28 port LED	Flashing	The QSFP28 port is sending or receiving data at 100 Gbps.
	Steady on	A 100 Gbps link is present on the QSFP28 port.
	Off	No link is present on the QSFP28 port.

Ports

Table2-417 Port specifications

Card model

Description

Connector type

Port quantity

Port transmission speed

RX-NIC-LGQ4L

4-port 50G Ethernet optical interface card

Standard Ethernet mode: 50 Gbps

Flexible Ethernet mode: 50 Gbps

Technical specifications

Table2-418 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.90 kg (1.98 lb)
Maximum power consumption	92 W
Minimum power consumption	55 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

RX-NIC-XP10L

View

Figure2-111 RX-NIC-XP10L view

(1) 10GBASE-R/W-SFP+ fiber ports (10 in total)	(2) SFP+ port LED. For the LED description, see Table2-419.

LEDs

Table2-419 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 100/1000 Mbps.

Ports

Table2-420 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
RX-NIC-XP10L	10-port 10GBASE-R/W Ethernet optical interface card	LC	10	100 Mbps
				1000 Mbps
				10 Gbps

Technical specifications

Table2-421 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.65 kg (1.43 lb)
Maximum power consumption	27.4 W
Minimum power consumption	26.9 W
Operating temperature	0°C to 45°C (32°F to 113°F)

RX-NIC-XP20L

View

Figure2-112 RX-NIC-XP20L view

(1) 10GBASE-R/W-SFP+ fiber ports (20 in total)	(2) SFP+ port LED. For the LED description, see Table2-422.

LEDs

Table2-422 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 100/1000 Mbps.

Ports

Table2-423 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
RX-NIC-XP20L	20-port 10GBASE-R/W Ethernet optical interface card	LC	20	100 Mbps
				1000 Mbps
				10 Gbps

Technical specifications

Table2-424 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	1.00 kg (2.20 lb)
Maximum power consumption	58 W
Minimum power consumption	39 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

RX-NIC-XP5L

View

Figure2-113 RX-NIC-XP5L view

(1) 10GBASE-R/W-SFP+ fiber ports (5 in total)	(2) SFP+ port LED. For the LED description, see Table2-425.

LEDs

Table2-425 SFP + port LED description

LED	Status	Description
SFP + port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of an SFP+ port by observing the color of its LED. Green indicates a speed of 10 Gbps, and yellow indicates a speed of 100/1000 Mbps.

Ports

Table2-426 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
RX-NIC-XP5L	5-port 10GBASE-R/W Ethernet optical interface card	LC	5	100 Mbps
				1000 Mbps
				10 Gbps

Technical specifications

Table2-427 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.60 kg (1.32 lb)
Maximum power consumption	14.9 W
Minimum power consumption	11 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

RX-NIC-YGS4L

View

Figure2-114 RX-NIC-YGS4L view

(1) 10GBASE-R-SFP+ port or 25GBASE-R-SFP28 port (4 in total)	(2) SFP28 port LED. For the LED description, see Table2-428.

LEDs

Table2-428 SFP28 port LED description

LED	Status	Description
SFP28 port LED	Flashing	The port is sending or receiving data.
	Steady on	A link is present on the port.
	Off	No link is present on the port.

NOTE:

You can identify the speed of a QSFP28 port by observing the color of its LED. Green indicates a speed of 100 Gbps, and yellow indicates a speed of 50 Mbps.

Ports

Table2-429 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
RX-NIC-YGS4L	4-port 25G Ethernet optical interface card	LC	4	10 Gbps
RX-NIC-YGS4L	4-port 25G Ethernet optical interface card	LC	4	25 Gbps

Technical specifications

Table2-430 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 mm × 179 mm × 118 mm (1.87 in × 7.05 in × 4.65 in)
Weight	0.80 kg (1.76 lb)
Maximum power consumption	38 W
Minimum power consumption	25 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

PIC subcards

IMPORTANT:

· To use a PIC interface card, you must install it on a CMPE, SPE, or SPEX/CSPEX base card. You cannot install it directly on the router.

· For the compatibility between PIC interface cards and CMPE, SPE, or SPEX/CSPEX base cards, see the compatibility information for the base cards.

PIC-GP10L

View

Figure2-115 PIC-GP10L view

(1) 1000BASE-X-SFP Ethernet fiber port (10 in total)	(2) SFP port LED. For the LED description, see Table2-431.

LEDs

Table2-431 GE SFP port LED description

LED	Status	Description
GE SFP port LED (LINK/ACT)	Flashing green	The SFP port is sending or receiving data.
	Green	A link is present on the SFP port.
	Off	No link is present on the SFP port.

Ports

Table2-432 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
PIC-GP10L	10-port 1000BASE-X optical interface card (SFP, LC)	LC	10	100 Mbps
PIC-GP10L	10-port 1000BASE-X optical interface card (SFP, LC)	LC	10	1000 Mbps

Technical specifications

Table2-433 PIC-GP10L

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.45 kg (0.99 lb)
Maximum power consumption	21 W
Minimum power consumption	9.5 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

PIC-PS2G4L

View

Figure2-116 PIC-PS2G4L view

(1) OC48c/STM16c-SFP POS fiber ports (2 in total)	(2) 1000BASE-X-SFP GE fiber ports (4 in total)
(3) POS port LED. For the LED description, see Table2-434.	(4) GE port LED. For the LED description, see Table2-435.

LEDs

Table2-434 WAN port LED description

LED	Status	Description
WAN port LED (ACT/ALM)	Green	The port is up and is receiving or sending data correctly.
	Steady red	An alarm has occurred.
	Off	The port is down.

Table2-435 GE SFP port LED description

LED	Status	Description
GE SFP port LED (LINK/ACT)	Flashing green	The SFP port is sending or receiving data.
	Green	A link is present on the SFP port.
	Off	No link is present on the SFP port.

Ports

Table2-436 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
PIC-PS2G4L	2-port OC-48c/STM-16c POS optical interface (SFP, LC) + 4-port 1000BASE-X optical interface card (SFP, LC)	LC	2	2.5 Gbps (OC-48/STM-16)
			4	100 Mbps
			4	1000 Mbps

Technical specifications

Table2-437 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.40 kg (0.88 lb)
Maximum power consumption	16 W
Minimum power consumption	9.3 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

PIC-PSP4L

View

Figure2-117 PIC-PSP4L view

(1) OC48c/STM16c-SFP POS fiber ports (4 in total)	(2) Port LED. For the LED description, see Table2-438.

LEDs

Table2-438 WAN port LED description

LED	Status	Description
WAN port LED (ACT/ALM)	Green	The port is up and is receiving or sending data correctly.
	Steady red	An alarm has occurred.
	Off	The port is down.

Ports

Table2-439 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
PIC-PSP4L	4-port OC-48c/STM-16c POS optical interface card (SFP, LC)	LC	4	2.5 Gbps (OC-48/STM-16)

Technical specifications

Table2-440 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.40 kg (0.88 lb)
Maximum power consumption	18 W
Minimum power consumption	9.7 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

PIC-PUP1L

View

Figure2-118 PIC-PUP1L view

(1) OC192c/STM64c-XFP POS fiber port (1 in total)	(2) Port LED. For the LED description, see Table2-441.

LEDs

Table2-441 WAN port LED description

LED	Status	Description
WAN port LED (ACT/ALM)	Green	The port is up and is receiving or sending data correctly.
	Steady red	An alarm has occurred.
	Off	The port is down.

Ports

Table2-442 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
PIC-PUP1L	1-port OC-192c/STM-64c POS optical interface card (XFP, LC)	LC	1	10 Gbps (OC-192/STM-64)

Technical specifications

Table2-443 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.50 kg (1.10 lb)
Maximum power consumption	19 W
Minimum power consumption	14.3 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

PIC-TCP8L

View

Figure2-119 PIC-TCP8L view

(1) OC3c/OC12c/1000BASE-X-SFP POS/GE fiber ports (8 in total)	(2) Port LED. For the LED description, see Table2-444.

LEDs

Table2-444 WAN port LED description

LED	Status	Description
WAN port LED (ACT/ALM)	Green	The port is up and is receiving or sending data correctly.
	Steady red	An alarm has occurred.
	Off	The port is down.

Ports

Table2-445 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
PIC-TCP8L	8-port OC-3c/OC-12c POS/GE optical interface card (SFP, LC)	LC	8	100 Mbps
				155 Mbps (OC-3/STM-1)
				622 Mbps (OC-12/STM-4)
				1000 Mbps

Technical specifications

Table2-446 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.40 kg (0.88 lb)
Maximum power consumption	17 W
Minimum power consumption	9.7 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

PIC-XP1L

View

Figure2-120 PIC-XP1L view

(1) 10GBASE-R/W-XFP Ethernet fiber port (1 in total)	(2) XFP port LED. For the LED description, see Table2-447.

LEDs

Table2-447 10GE XFP port LED description

LED	Status	Description
10GE XFP port LED (LINK/ACT)	Flashing green	The XFP port is sending or receiving data.
	Green	A link is present on the XFP port.
	Off	No link is present on the XFP port.

Ports

Table2-448 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
PIC-XP1L	1-port 10GBASE-R/W Ethernet optical interface card (XFP, LC)	LC	1	10 Gbps

Technical specifications

Table2-449 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.45 kg (0.99 lb)
Maximum power consumption	23.7 W
Minimum power consumption	12.5 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

OAA modules

A combo interface is a logical interface that contains an SFP port and an RJ-45 Ethernet port. Only one of them can be activated at a time.

LSU1ADECEA0

View

Figure2-121 LSU1ADECEA0 view

(1) Console port (CONSOLE)	(2) USB port (reserved for future use)
(3) Combo copper port (10/100/1000BASE-T)	(4) Combo copper port LED (LINK/ACT)
(5) Combo fiber port (1000BASE-X)	(6) Combo fiber port LED (LINK/ACT)
(7) Alarm LED (ALM)	(8) System LED (RUN)
(9) Ejector lever	(10) Captive screw

LEDs

Table2-450 LED description

LED	Mark	Status	Description
Alarm LED	ALM	Off	The system is operating correctly.
Alarm LED	ALM	Steady red	A critical fault is present on the system and the fault must be handled immediately.
System LED	RUN	Off	No power is input or the service module has failed.
		Steady green	The system is running incorrectly.
		Slow flashing green (1 Hz)	The system is operating correctly.
		Fast flashing green (8 Hz)	The system is loading software or has not started.
Combo interface LED	LINK/ACT	Off	No link is present.
		Steady green	A link is present.
		Flashing green	The interface is sending or receiving data.

Ports

Table2-451 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
LSU1ADECEA0	Application delivery service module	RJ-45	2	10/100/1000 Mbps
LSU1ADECEA0	Application delivery service module	LC	2	1000 Mbps

Technical specifications

Table2-452 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.90 kg (8.60 lb)
Maximum power consumption	150 W
Minimum power consumption	109 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

IM-ACG1000X-IV

View

Figure2-122 IM-ACG1000X-IV view

(1) Captive screw	(2) Ejector lever
(3) Drive slot	(4) Console port (CONSOLE)
(5) GE Ethernet copper interface (10/100/1000BASE-T)	(6) USB port
(7) Drive LED (HD)	(8) System LED (SYS)

LEDs

Table2-453 LED description

LED	Mark	Status	Description
Drive LED	HD	Fast flashing green	Data is being read from or written to the drive.
		Steady green	The drive is running correctly.
		Off	The drive is absent.
System LED	SYS	Off	No power is input or the service module has failed.
		Slow flashing green	The system is operating correctly.
		Fast flashing green	The system is loading software.

Ports

Table2-454 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
IM-ACG1000X-IV	Application control gateway module	RJ45	1	10/100/1000 Mbps

Technical specifications

Table2-455 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	4.80 kg (10.60 lb)
Maximum power consumption	235 W
Minimum power consumption	175 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

IM-IPSX-IV

View

Figure2-123 IM-IPSX-IV view

(1) Captive screw	(2) Ejector lever
(3) Drive slot	(4) Console port (CONSOLE)
(5) GE Ethernet copper interface (10/100/1000BASE-T)	(6) USB port
(7) Drive LED (HD)	(8) System LED (SYS)

LEDs

Figure2-124 LED description

LED	Mark	Status	Description
Drive LED	HD	Fast flashing green	Data is being read from or written to the drive.
		Steady green	The drive is running correctly.
		Off	The drive is absent.
System LED	SYS	Off	No power is input or the service module has failed.
		Slow flashing green	The system is operating correctly.
		Fast flashing green	The system is loading software.

Ports

Table2-456 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
IM-IPSX-IV	Intrusion prevention system module	RJ45	1	10/100/1000 Mbps

Technical specifications

Table2-457 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	4.80 kg (10.58 lb)
Maximum power consumption	235 W
Minimum power consumption	175 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

IM-NGFWX-IV

View

Figure2-125 IM-NGFWX-IV view

(1) Captive screw	(2) Ejector lever
(3) Drive slot	(4) Console port (CONSOLE)
(5) GE Ethernet copper interface (10/100/1000BASE-T)	(6) USB port
(7) Drive LED (HD)	(8) System LED (SYS)

LEDs

Table2-458 LED description

LED	Mark	Status	Description
Drive LED	HD	Fast flashing green	Data is being read from or written to the drive.
		Steady green	The drive is running correctly.
		Off	The drive is absent.
System LED	SYS	Off	No power is input or the service module has failed.
		Slow flashing green	The system is operating correctly.
		Fast flashing green	The system is loading software.

Ports

Table2-459 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
IM-NGFWX-IV	Firewall module	RJ45	1	10/100/1000 Mbps

Technical specifications

Table2-460 Technical specifications

Item	Description
Dimensions (H × W × D)	40 mm × 399 mm × 352 mm (1.57 in × 15.71 in × 13.86 in)
Weight	4.80 kg (10.58 lb)
Maximum power consumption	235 W
Minimum power consumption	175 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

LSU1FWCEA0

View

Figure2-126 LSU1FWCEA0 view

(1) Console port (CONSOLE)	(2) USB port (reserved for future use)
(3) Combo copper port (10/100/1000BASE-T)	(4) Combo copper port LED (LINK/ACT)
(5) Combo fiber port (1000BASE-X)	(6) Combo fiber port LED (LINK/ACT)
(7) Alarm LED (ALM)	(8) System LED (RUN)
(9) Ejector lever	(10) Captive screw

LEDs

Table2-461 LED description

LED	Mark	Status	Description
Alarm LED	ALM	Off	The system is operating correctly.
Alarm LED	ALM	Steady red	A critical fault has occurred to the system and the fault must be handled immediately.
System LED	RUN	Off	No power is input or the service module has failed.
		Steady green	The system is running incorrectly.
		Slow flashing green (1 Hz)	The system is operating correctly.
		Fast flashing green (8 Hz)	The system is loading software or has not started.
Combo interface LED	LINK/ACT	Off	No link is present.
		Steady green	A link is present.
		Flashing green	The interface is sending or receiving data.

Ports

Table2-462 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
LSU1FWCEA0	Firewall module	RJ45	2	10/100/1000 Mbps
LSU1FWCEA0	Firewall module	LC	2	1000 Mbps

Technical specifications

Table2-463 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.90 kg (8.60 lb)
Maximum power consumption	150 W
Minimum power consumption	109 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

LSU1IPSBEA0

View

Figure2-127 LSU1IPSBEA0 view

(1) Console port (CONSOLE)	(2) USB port ( Control power supply of the external PFC power fail safeguard module)
(3) Combo copper port (10/100/1000BASE-T)	(4) Combo copper port LED (LINK/ACT)
(5) Combo fiber port (1000BASE-X)	(6) Combo fiber port LED (LINK/ACT)
(7) Alarm LED (ALM)	(8) System LED (RUN)
(9) Ejector lever	(10) Captive screw

LEDs

Table2-464 LED description

LED	Mark	Status	Description
Alarm LED	ALM	Off	The system is operating correctly.
Alarm LED	ALM	Steady red	A critical fault has occurred to the system and the fault must be handled immediately.
System LED	RUN	Off	No power is input or the service module has failed.
		Steady green	The system is running incorrectly.
		Slow flashing green (1 Hz)	The system is operating correctly.
		Fast flashing green (8 Hz)	The system is loading software or has not started.
Combo interface LED	LINK/ACT	Off	No link is present.
		Steady green	A link is present.
		Flashing green	The interface is sending or receiving data.

Ports

Table2-465 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
LSU1IPSBEA0	Intrusion prevention system module	RJ45	2	10/100/1000 Mbps
LSU1IPSBEA0	Intrusion prevention system module	LC	2	1000 Mbps

Technical specifications

Table2-466 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.90 kg (8.60 lb)
Maximum power consumption	150 W
Minimum power consumption	109 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

LSU3FWCEA0

View

Figure2-128 LSU3FWCEA0 view

(1) Console port (CONSOLE)	(2) USB port (reserved for future use)
(3) Combo copper port (10/100/1000BASE-T)	(4) Combo copper port LED (LINK/ACT)
(5) Combo fiber port (1000BASE-X)	(6) Combo fiber port LED (LINK/ACT)
(7) Alarm LED (ALM)	(8) System LED (RUN)
(9) Ejector lever	(10) Captive screw

LEDs

Table2-467 LED description

LED	Mark	Status	Description
Alarm LED	ALM	Off	The system is operating correctly.
Alarm LED	ALM	Steady red	A critical fault has occurred to the system and the fault must be handled immediately.
System LED	RUN	Off	No power is input or the service module has failed.
		Steady green	The system is running incorrectly.
		Slow flashing green (1 Hz)	The system is operating correctly.
		Fast flashing green (8 Hz)	The system is loading software or has not started.
Combo interface LED	LINK/ACT	Off	No link is present.
		Steady green	A link is present.
		Flashing green	The interface is sending or receiving data.

Ports

Table2-468 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
LSU3FWCEA0	Firewall module	RJ45	2	10/100/1000 Mbps
LSU3FWCEA0	Firewall module	LC	2	1000 Mbps

Technical specifications

Table2-469 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	3.90 kg (8.60 lb)
Maximum power consumption	150 W
Minimum power consumption	109 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

Configuration restrictions and guidelines

For adequate ventilation and cooling, install the IM-NGFWX-IV, IM-IPSX-IV, and IM-ACG1000X-IV cards in the following slots only when the other slots are not available.

· SR8808-X router—Slots 0, 8 and 9.

· SR8812-X router—Slots 0 and 13.

Compatibility information

Table2-470 Compatibility matrix between OAA cards and routers

Card model	SR8804-X, SR8808-X, SR8812-X	SR8808H-X, SR8816-X
IM-NGFWX-IV	Supported	Supported
LSU1FWCEA0	Supported	Not supported
LSU3FWCEA0	Supported	Not supported
IM-IPSX-IV	Supported	Supported
LSU1IPSBEA0	Supported	Not supported
IM-ACG1000X-IV	Supported	Supported
LSU1ADECEA0	Supported	Not supported

IM modules (Universal line processing unit)

IM-APA-I

NOTE:

The IM-APA-I provides one subcard slot. You can use it with an IM-SP-B subcard for double iBRAS packet processing rate.

View

Figure2-129 IM-APA-I view

(1) Card status LED. For the LED description, see Table2-471.

LEDs

Table2-471 Card status LED description

LED	Status	Description
RUN (Green)	Steady on	The card is faulty.
	Off	The card is faulty or is not in position.
	Flashing (once per second)	The card is operating correctly.
	Fast flashing	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Ports

Table2-472 Port specifications

Card model	Description
IM-APA-I	iBRAS application-aware line processing unit

Technical specifications

Table2-473 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 × 399 × 352 mm (2.07 × 15.71 × 13.86 in)
Weight	3.12 kg (6.88 lb)
Maximum power consumption	400 W
Power consumption (with typical configuration)	260 W
Minimum power consumption	248 W
Operating temperature	0°C to 45°C (32°F to 113°F)

IM-APA-I3

NOTE:

The IM-APA-I3 provides one subcard slot. You can use it with an IM-SP-B3 subcard for double iBRAS packet processing rate.

View

Figure2-130 IM-APA-I3 view

(1) Card status LED. For the LED description, see Table2-474.

LED

Table2-474 Card status LED description

LED	Status	Description
RUN (Green)	Steady on	The card is faulty.
	Off	The card is faulty or is not in position.
	Flashing (once per second)	The card is operating correctly.
	Fast flashing (four times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Ports

Table2-475 Port specifications

Card model	Description
IM-APA-I3	iBRAS application-aware line processing unit

Technical specifications

Table2-476 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 × 399 × 361 mm (2.07 × 15.71 × 14.21 in)
Weight	8.93 kg (19.69 lb)
Maximum power consumption	516 W
Power consumption (with typical configuration)	274 W
Minimum power consumption	265 W
Operating temperature	0°C to 45°C (32°F to 113°F)

IM-MSUX (1 U)

View

Figure2-131 IM-MSUX (1 U) view

(1) Card status LED. For the LED description, see Table2-477.

LED

Table2-477 Card status LED description

LED	Status	Description
RUN (green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (once per second)	The card is operating correctly.
	Fast flashing	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Ports

Table2-478 Port specifications

Card model	Description
IM-MSUX (1 U)	Universal line processing unit

Technical specifications

Table2-479 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Weight	4.95 kg (10.91 lb)
Maximum power consumption	186 W
Typical power consumption	175 W
Minimum power consumption	158.2 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

IM-MSUX (1.2 U)

View

Figure2-132 IM-MSUX (1.2 U) view

(1) Card status LED. For the LED description, see Table2-480.

LEDs

Table2-480 Card status LED description

LED	Status	Description
RUN (green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (once per second)	The card is operating correctly.
	Fast flashing	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Ports

Table2-481 Port specifications

Card model	Description
IM-MSUX (1.2 U)	Universal line processing unit

Technical specifications

Table2-482 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 × 399 × 352 mm (2.07 × 15.71 × 13.86 in)
Weight	4.85 kg (10.69 lb)
Maximum power consumption	186 W
Typical power consumption	175 W
Minimum power consumption	158.2 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

IM-MSEX-B

NOTE:

The IM-MSEX-B provides one subcard slot. You can use it without a subcard, or use it with an IM-SP-B subcard for double CGN packet processing rate.

View

Figure2-133 IM-MSEX-B view

(1) Card status LED. For the LED description, see Table2-483.

LEDs

Table2-483 Card status LED description

LED	Status	Description
RUN (green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (once per second)	The card is operating correctly.
	Fast flashing	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Ports

Table2-484 Port specifications

Card model	Description
IM-MSEX-B	Service processing unit

Technical specifications

Table2-485 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 × 399 × 352 mm (2.07 × 15.71 × 13.86 in)
Weight	3.12 kg (6.88 lb)
Maximum power consumption	400 W
Typical power consumption	260 W
Minimum power consumption	248 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

IM-MSEX-B3

NOTE:

The IM-MSEX-B3 provides one subcard slot. You can use it without a subcard, or use it with an IM-SP-B3 subcard for double CGN packet processing rate.

View

Figure2-134 IM-MSEX-B3 view

(1) Card status LED. For the LED description, see Table2-486.

LEDs

Table2-486 Card status LED description

LED	Status	Description
RUN (Green)	Steady on	The card is faulty.
	Off	The card is faulty or is not in position.
	Flashing (once per second)	The card is operating correctly.
	Fast flashing (four times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Ports

Table2-487 Port specifications

Card model	Description
IM-MSEX-B3	Service processing unit

Technical specifications

Table2-488 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 × 399 × 361 mm (2.07 × 15.71 × 14.21 in)
Weight	8.93 kg (19.69 lb)
Maximum power consumption	516 W
Power consumption (with typical configuration)	274 W
Minimum power consumption	265 W
Operating temperature	0°C to 45°C (32°F to 113°F)

IM-SP-B

NOTE:

The IM-SP-B subcard must be installed on an IM-APA-I or IM-MSEX-B for use. It occupies one subcard slot and does not provide ports.

View

Figure2-135 IM-SP-B view

(1) Card status LED. For the LED description, see Table2-489.

LEDs

Table2-489 Card status LED description

LED	Status	Description
RUN (green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (once per second)	The card is operating correctly.
	Fast flashing	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Ports

Table2-490 Port specifications

Card model	Description
IM-SP-B	Universal expansion service processing module

Technical specifications

Table2-491 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 × 170 × 192 mm (1.87 × 6.69 × 7.56 in)
Weight	1.20 kg (2.65 lb)
Maximum power consumption	130 W
Minimum power consumption	95 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

IM-SP-B3

NOTE:

The IM-SP-B3 subcard must be installed on an IM-APA-I3 or IM-MSEX-B3 for use. It occupies one subcard slot and does not provide ports.

View

Figure2-136 IM-SP-B3 view

(1) Card status LED. For the LED description, see Table2-492.

LEDs

Table2-492 Card status LED description

LED	Status	Description
RUN (Green)	Steady on	The card is faulty.
	Off	The card is faulty or is not in position.
	Flashing (once per second)	The card is operating correctly.
	Fast flashing (four times per second)	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Ports

Table2-493 Port specifications

Card model	Description
IM-SP-B3	Universal expansion service processing module

Technical specifications

Table2-494 Technical specifications

Item	Description
Dimensions (H × W × D)	47.5 × 190 × 154 mm (1.87 × 7.48 × 6.06 in)
Weight	1.26 kg (2.78 lb)
Maximum power consumption	127 W
Minimum power consumption	124 W
Operating temperature	0°C to 45°C (32°F to 113°F)

Configuration restrictions and guidelines

For adequate ventilation and cooling, install the IM-MSUX cards in the following slots only when the other slots are not available:

· SR8808-X router—Slots 0, 8 and 9.

· SR8812-X router—Slots 0 and 13.

Compatibility information

Table2-495 Compatibility matrix between universal line processing units and routers

Card model	SR8804-X	SR8808-X, SR8812-X	SR8808H-X, SR8816-X
IM-APA-I	Not supported	Not supported	Supported
IM-APA-I3	Not supported	Not supported	Supported
IM-MSUX (1 U)	Supported	Supported	Supported
IM-MSUX (1.2 U)	Not supported	Not supported	Supported
IM-MSEX-B	Not supported	Not supported	Supported
IM-MSEX-B3	Not supported	Not supported	Supported

IM modules (Security monitor line processing unit)

IM-SMUX

View

Figure2-137 IM-SMUX view

(1) Card status LED. For the LED description, see Table2-496.

LEDs

Table2-496 Card status LED description

LED	Status	Description
RUN (green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing	The card is starting up. If the LED keeps fast flashing, the card fails registration.

Ports

Table2-497 Port specifications

Card model	Description
IM-SMUX	Security monitor line processing unit

Technical specifications

Table2-498 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 × 399 × 352 mm (2.07 × 15.71 × 13.86 in)
Weight	4.85 kg (10.69 lb)
Maximum power consumption	186 W
Typical power consumption	175 W
Minimum power consumption	159 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

Compatibility information

Table2-499 Compatibility matrix between security monitor line processing units and routers

Card model	SR8804-X	SR8808-X, SR8812-X	SR8808H-X, SR8816-X
IM-SMUX	Not supported	Not supported	Supported

IM modules (Network data encryption service processing unit)

IM-SFMX

NOTE:

The IM-SFMX provides one subcard slot. When used without a subcard, it uses non-SM algorithms to encrypt and decrypt network data. When used with an MIC-SM, it uses SM algorithms to encrypt and decrypt network data.

View

Figure2-138 IM-SFMX view

(1) Card status LED. For the LED description, see Table2-500.

LEDs

Table2-500 Card status LED description

LED	Status	Description
RUN (green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Ports

Table2-501 Port specifications

Card model	Description
IM-SFMX	Network data encryption service processing unit

Technical specifications

Table2-502 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 399 × 355 mm (1.57 × 15.71 × 13.86 in)
Weight	4.05 kg (8.93 lb)
Maximum power consumption	165 W
Typical power consumption	113 W
Minimum power consumption	90 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

MIC-SEC

NOTE:

The MIC-SEC occupies one subcard slot. It must be installed on a base card for use. For compatibilities between the MIC-SEC subcard and MPE, SPE, or SPEX/CSPEX base cards, see compatibility information for the base cards.

View

Figure2-139 MIC-SEC view

Ports

Table2-503 Port specifications

Card model	Description	Connector type	Port quantity	Port transmission speed
MIC-SEC	Network data encryption service processing interface card	N/A	N/A	N/A

Technical specifications

Table2-504 Technical specifications

Item	Description
Dimensions (H × W × D)	18 × 171 × 157 mm (0.71 × 6.73 × 6.18 in)
Weight	0.40 kg (0.88 lb)
Maximum power consumption	31 W
Minimum power consumption	29 W
Operating temperature	0°C to 45°C (32°F to 113°F)

MIC-SM

NOTE:

· The MIC-SM is not hot swappable.

· The MIC-SM must be installed on an IM-SFMX for use. It occupies one subcard slot.

· The MIC-SM is provided with six USB keys for you to obtain user roles to manage the card. To obtain a user role, first insert a USB key into USB port AUTH. For more information about the encryption card configuration, see H3C SR8800-X Routers Configuration Guides.

View

Figure2-140 MIC-SM view

(1) Card status LED. For the LED description, see Table2-505.	(2) USB port KEY (reserved for future use)
(3) USB port AUTH

LEDs

Table2-505 Card status LED description

LED	Status	Description
RUN (green)	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (about once per second)	The card is operating correctly.
	Fast flashing	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Ports

Table2-506 Port specifications

Card model	Description
MIC-SM	Network data encryption interface card

Technical specifications

Table2-507 Technical specifications

Item	Description
Dimensions (H × W × D)	37 × 179 × 149 mm (1.46 in × 7.05 in × 5.87 in)
Weight	0.90 kg (1.98 lb)
Maximum power consumption	40 W
Minimum power consumption	25 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

Compatibility information

Table2-508 Compatibility matrix between security monitor line processing units and routers

Card model	SR8804-X	SR8808-X, SR8812-X	SR8808H-X, SR8816-X
IM-SMUX	Not supported	Not supported	Supported

IM modules (Universal open application platform)

IM-OAPX

View

Figure2-141 IM-OAPX view

No.	Description
(1)	Power on/standby button and system power LED
(2)	2.5 in SATA drive slot
(3)	Drive Present/Active LED
(4)	Drive Fault/UID LED
(5)	BMC network port (1 Gb, RJ45) with default IP 192.168.1.2/24
(6)	Shared network port, which can be used as the following: · Ethernet port (1Gb, RJ45) · BMC network port (1Gb, RJ45), with default IP automatically obtained through DHCP)
(7)	BMC network port status LED
(8)	Shared network port status LED
(9)	VGA connector
(10)	USB 2.0 port
(11)	USB 3.0 port
(12)	Console port
(13)	UID LED
(14)	RUN LED
(15)	Health LED

LEDs

Table2-509 System power LED description

LED	Status	Description
Power on/standby button and system power LED	Steady green	The system has started up.
	Flashing green (1 Hz)	The system is starting up.
	Steady amber	The system is in standby mode.
	Off	The system is powered off.

Table2-510 Health LED description

LED	Status	Description
Health LED	Steady green	The system is operating correctly.
	Flashing green (4 Hz)	The BMC is currently resetting and initializing.
	Flashing yellow and green (1 Hz)	A minor alarm occurs in the system, including an alarm on an error monitored by BMC or an alarm on hardware.
	Flashing yellow (1 Hz)	A major alarm occurs in the system, including an alarm on an error monitored by BMC, an alarm on hardware or CPU.

Table2-511 RUN LED description

LED	Status	Description
RUN LED	Steady on	The card is faulty.
	Off	The card is faulty or is not present.
	Flashing (1 Hz)	The card is operating correctly.
	Fast flashing	The card is starting up. If the LED keeps fast flashing, card registration has failed.

Table2-512 UID LED description

LED	Status	Description
UID LED	Steady blue	The UID LED is activated. You can activate the UID LED in the following methods: · Press down the UID LED. · Power on the UID LED from BMC.
	Flashing blue	· 1 Hz: The system is being remote managed by BMC or performing software update. · 4Hz: BMC is restarting by pressing the UID button or LED for 8 seconds.
	Off	The UID LED is not activated.

Table2-513 Drive LED description

Fault/UID LED (orange/blue)	Present/Active LED (green)	Description
Flashing orange (0.5 Hz)	Steady green/flashing green (4 Hz)	A predictive alarm occurs on the drive. Replace the drive in time.*
Steady orange	Steady green/flashing green (4 Hz)	An error occurs on the drive. Replace the drive immediately.
Steady blue	Steady green/flashing green (4 Hz)	The drive is operating correctly and has been selected by the array management tool.
Off	Flashing (4 Hz)	The drive is present. Data is being read from or written to the drive, or the drive is being used for array migration or rebuilding.
Off	Steady on	The drive is present but no data being read from or written to the drive.
Off	Off	The drive is not installed properly.

Table2-514 BMC network port LED description

LED	Status	Description
BMC network port LED	Steady green	The network port is being activated.
	Flashing green (1 Hz)	The network port is receiving or sending data.
	Off	The network port is disconnected.

Table2-515 Shared network port LED description

LED	Status	Description
Shared network port LED	Steady green	The network port is being activated.
	Flashing green (1 Hz)	The network port is receiving or sending data.
	Off	The network port is disconnected.

Ports

Table2-516 Port specifications

Card model	Description
IM-OAPX	Universal open application platform

Technical specifications

Table2-517 Technical specifications

Item	Description
Dimensions (H × W × D)	52.5 × 399 × 352 mm (2.07 × 15.71 × 13.86 in)
Weight	6.25 kg (13.78 lb)
Maximum power consumption	320 W
Typical power consumption	310 W
Minimum power consumption	295 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)
Processor	Intel Skylake Xeon CPU · A maximum power consumption of 205 W · A maximum of 2.6 GHz CPU clock speed · 38.5 MB cache
Memory	Support six DDR4 memory modules · Single DIMM capacity: 32 GB · Total memory capacity: 192 GB
Storage	Maximum storage capacity: 2 × 960 GB
Chipset	Intel C62x Lewisburg chipset compatible with LBG-T SKU
User port	· 2 × console ports · 1 × BMC network port · 1 × shared network port (used as an Ethernet port or a BMC network port) · 1 × VGA connector · 1 × USB port (USB 3.0) · 2 × USB ports (USB 2.0)

Table2-518 Drive specifications

Model	Capacity	Interface type	Interface rate
UIS-SSD-960GB-SATA-6G-SFF-EV	960 G	SATA	6 Gbps
UN-SSD-960G-SATA-6G-SFF-EV-1	960 G	SATA	6 Gbps

Configuration restrictions and guidelines

To avoid data loss on drives, you must shut down the universal open application platform before performing the following operations:

· Reboot or hot swap the universal open application platform.

· Reboot or shut down the router.

Do not install the universal open application platform in slot 6 of the SR8808-X router or slot 8 of the SR8812-X router.

The console port on the panel of the universal open application platform is only for users. The internal console port of the universal open application platform is only for H3C Support to perform maintenance and updates. Operations without permission are not allowed. H3C will not be liable for any consequences caused thereby.

The shared network interface can operate only at 1000 Mbps and can be connected only with a GE Ethernet port.

USB ports on the universal open application platform do not support extension cable connection.

Compatibility information

Table2-519 Compatibility matrix between the universal open application platform and routers

Card model	SR8804-X	SR8808-X, SR8812-X	SR8808H-X, SR8816-X
IM-OAPX	Supported	Supported	Supported

Switching fabric modules

SFC-04-1/SFC-04-2/SFC-04-3/SFC-04-4

View

Figure2-142 SFC-04-1 view

NOTE:

The views of the SFC-04-1, SFC-04-2, SFC-04-3, and SFC-04-4 are similar. This figure uses the SFC-04-1 as an example.

Technical specifications

Table2-520 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 256 × 298 mm (1.57 × 10.08 × 11.73 in)
Weight	1.00 kg (2.20 lb)
Maximum power consumption	N/A
Minimum power consumption	N/A
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

SFC-04B/SFC-04D

View

Figure2-143 SFC-04B view

(1) Switching fabric module status LED. For the LED description, see Table2-521.	(2) Console port

NOTE:

The views of the SFC-04B and SFC-04D are similar. This figure uses the SFC-04B as an example.

LEDs

Table2-521 Switching fabric module status LED description

LED status		Description
RUN	ALM	Description
Flashing (0.5 Hz)	Off	The switching fabric module is operating correctly.
Off	Steady on	The switching fabric module is faulty.
Flashing (0.5 Hz)	Steady on	The temperature of the switching fabric module has exceeded the upper limit or dropped below the lower limit.
Off	Off	The switching fabric module has not started up.
Steady on	Off	The switching fabric module is starting up.

Technical specifications

Table2-522 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 256 × 298 mm (1.57 × 10.08 × 11.73 in)
Weight	· SFC-04B: 1.75 kg (3.86 lb) · SFC-04D: 1.71 kg (3.77 lb)
Maximum power consumption	· SFC-04B: 65 W · SFC-04D: 80 W
Typical power consumption	· SFC-04B: 59 W · SFC-04D: 72 W
Minimum power consumption	· SFC-04B: 48 W · SFC-04D: 60 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

SFC-08B/SFC-08D

View

Figure2-144 SFC-08B view

(1) Console port	(2) Switching fabric module status LED. For the LED description, see Table2-523.

NOTE:

The views of the SFC-08B and SFC-08D are similar. This figure uses the SFC-08B as an example.

LEDs

Table2-523 Switching fabric module status LED description

LED status		Description
RUN	ALM	Description
Flashing (0.5 Hz)	Off	The switching fabric module is operating correctly.
Off	Steady on	The switching fabric module is faulty.
Flashing (0.5 Hz)	Steady on	The temperature of the switching fabric module has exceeded the upper limit or dropped below the lower limit.
Off	Off	The switching fabric module has not started up.
Steady on	Off	The switching fabric module is starting up.

Technical specifications

Table2-524 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 426 × 298 mm (1.57 × 16.77 × 11.73 in)
Weight	· SFC-08B: 2.50 kg (5.51 lb) · SFC-08D: 2.77 kg (6.11 lb)
Maximum power consumption	· SFC-08B: 60 W · SFC-08D: 135 W
Typical power consumption	· SFC-08B: 54 W · SFC-08D: 122 W
Minimum power consumption	· SFC-08B: 44 W · SFC-08D: 101 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

SFC-08E

View

Figure2-145 SFC-08E view

(1) Switching fabric module status LED. For the LED description, see Table2-525.

LEDs

Table2-525 Switching fabric module status LED description

LED status		Description
RUN	ALM	Description
Flashing (0.5 Hz)	Off	The switching fabric module is operating correctly.
Off	Steady on	The switching fabric module is faulty.
Flashing (0.5 Hz)	Steady on	The temperature of the switching fabric module has exceeded the upper limit or dropped below the lower limit.
Off	Off	The switching fabric module has not started up.
Steady on	Off	The switching fabric module is starting up.

Technical specifications

Table2-526 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 426 × 298 mm (1.57 × 16.77 × 11.73 in)
Weight	3.55 kg (7.83 lb)
Maximum power consumption	140 W
Typical power consumption	130 W
Minimum power consumption	73 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

SFC-08E1/SFC-08T

View

Figure2-146 SFC-08T view

(1) Switching fabric module status LED. For the LED description, see Table2-527.

NOTE:

The views of the SFC-08E1 and SFC-08T are similar. This figure uses the SFC-08T as an example.

LEDs

Table2-527 Switching fabric module status LED description

RUN LED status	Description
Flashing (0.5 Hz)	The switching fabric module is operating correctly.
Flashing (8 Hz)	The switching fabric module is starting up.
Off	The switching fabric module has not started up.

Technical specifications

Table2-528 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 562 × 298 mm (1.57 × 22.13 × 11.73 in)
Weight	· CSFC-08E1: 5.20 kg (11.46 lb) · CSFC-08T: 5.15 kg (11.35 lb)
Maximum power consumption	· CSFC-08E1: 125 W · CSFC-08T: 129 W
Typical power consumption	· CSFC-08E1: 112 W · CSFC-08T: 116 W
Minimum power consumption	· CSFC-08E1: 75 W · CSFC-08T: 100 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

CSFC-08T-G

View

Figure2-147 CSFC-08T-G view

(1) Switching fabric module status LED. For the LED description, see Table2-529.

LEDs

Table2-529 Switching fabric module status LED description

RUN LED status	Description
Flashing (0.5 Hz)	The switching fabric module is operating correctly.
Flashing (8 Hz)	The switching fabric module is starting up.
Off	The switching fabric module has not started up.

Technical specifications

Table2-530 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 562 × 298 mm (1.57 × 22.13 × 11.73 in)
Weight	5.30 kg (11.68 lb)
Maximum power consumption	130 W
Typical power consumption	110 W
Minimum power consumption	100 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

SFC-12B /SFC-12D

View

Figure2-148 SFC-12B view

(1) Console port	(2) Switching fabric module status LED. For the LED description, see Table2-531.

NOTE:

The views of the SFC-12B and SFC-12D are similar. This figure uses the SFC-12B as an example.

LEDs

Table2-531 Switching fabric module status LED description

LED status		Description
RUN	ALM	Description
Flashing (0.5 Hz)	Off	The switching fabric module is operating correctly.
Off	Steady on	The switching fabric module is faulty.
Flashing (0.5 Hz)	Steady on	The temperature of the switching fabric module has exceeded the upper limit or dropped below the lower limit.
Off	Off	The switching fabric module has not started up.
Steady on	Off	The switching fabric module is starting up.

Technical specifications

Table2-532 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 602 × 298 mm (1.57 × 23.70 × 11.73 in)
Weight	· SFC-12B: 3.89 kg (8.58 lb) · SFC-12D: 4.51 kg (9.94 lb)
Maximum power consumption	· SFC-12B: 140 W · SFC-12D: 255 W
Typical power consumption	· SFC-12B: 126 W · SFC-12D: 230 W
Minimum power consumption	· SFC-12B: 107 W · SFC-12D: 195 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

SFC-12E

View

Figure2-149 SFC-12E view

(1) Console port	(2) Air inlet vents
(3) Switching fabric module status LED. For the LED description, see Table2-533.

LEDs

Table2-533 Switching fabric module status LED description

LED status		Description
RUN	ALM	Description
Flashing (0.5 Hz)	Off	The switching fabric module is operating correctly.
Off	Steady on	The switching fabric module is faulty.
Flashing (0.5 Hz)	Steady on	The temperature of the switching fabric module has exceeded the upper limit or dropped below the lower limit.
Off	Off	The switching fabric module has not started up.
Steady on	Off	The switching fabric module is starting up.

Technical specifications

Table2-534 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 602 × 298 mm (1.57 × 23.70 × 11.73 in)
Weight	5.30 kg (11.68 lb)
Maximum power consumption	178 W
Typical power consumption	161 W
Minimum power consumption	146 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

SFC-16T/SFC-16E

View

Figure2-150 SFC-16E view

(1) Switching fabric module status LED. For the LED description, see Table2-535.

NOTE:

The views of the SFC-16T and SFC-16E are similar. This figure uses the SFC-16E as an example.

LEDs

Table2-535 Switching fabric module status LED description

RUN LED status	Description
Flashing (0.5 Hz)	The switching fabric module is operating correctly.
Flashing (8 Hz)	The switching fabric module is starting up.
Off	The switching fabric module has not started up.

Technical specifications

Table2-536 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 961 × 298 mm (1.57 × 37.83 × 11.73 in)
Weight	· CSFC-16T: 10.25 kg (22.60 lb) · CSFC-16E: 10.50 kg (23.15 lb)
Maximum power consumption	· CSFC-16T: 402 W · CSFC-16E: 248 W
Typical power consumption	· CSFC-16T: 361 W · CSFC-16E: 220 W
Minimum power consumption	· CSFC-16T: 267 W · CSFC-16E: 159 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

CSFC-16T3

View

Figure2-151 CSFC-16T3 view

(1) Switching fabric module status LED. For the LED description, see Table2-537.

LEDs

Table2-537 Switching fabric module status LED description

RUN LED status	Description
Flashing (0.5 Hz)	The switching fabric module is operating correctly.
Flashing (8 Hz)	The switching fabric module is starting up.
Off	The switching fabric module has not started up.

Technical specifications

Table2-538 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 961 × 298 mm (1.57 × 37.83 × 11.73 in)
Weight	10.35 kg (22.82 lb)
Maximum power consumption	600 W
Power consumption (with typical configuration)	380 W
Minimum power consumption	256 W
Operating temperature	0°C to 45°C (32°F to 113°F)

CSFC-16T-G

View

Figure2-152 CSFC-16T-G view

(1) Switching fabric module status LED. For the LED description, see Table2-539.

LEDs

Table2-539 Switching fabric module status LED description

RUN LED status	Description
Flashing (0.5 Hz)	The switching fabric module is operating correctly.
Flashing (8 Hz)	The switching fabric module is starting up.
Off	The switching fabric module has not started up.

Technical specifications

Table2-540 Technical specifications

Item	Description
Dimensions (H × W × D)	40 × 961 × 298 mm (1.57 × 37.83 × 11.73 in)
Weight	10.30 kg (22.71 lb)
Maximum power consumption	120 W
Typical power consumption	110 W
Minimum power consumption	100 W
Operating temperature	0 °C to 45 °C (32 °F to 113 °F)

Configuration restrictions and guidelines

Do not mix Type-B, Type-D, Type-E, Type-T, and Type-TG switching fabric modules in any combinations on the same router.

If you use Type-B, Type-D, Type-E, Type-T, or Type-TG switching fabric modules for the router, a minimum of two are required. For an SR8808H-X router, you must install switching fabric modules in slots 10 and 12. Slot 11 can be used only when five switching fabric modules are required. For an SR8816-X router, you must install switching fabric modules in slots 18 and 20. Slot 19 can be used only when five switching fabric modules are required. For other routers, slots 1, 3, and 4 take precedence over the other slots for switching fabric module installation.

The console port on a switching fabric module is only for H3C Support to perform maintenance and updates. Operations without permission are not allowed. H3C will not be liable for any consequences caused thereby.

If Type-A switching fabric modules are used, use the four together and install each into the specified slot. Each Type-A switching fabric module has a mark specifying the slot for installation. For example, the SFC-04-1 has the mark Notes:Please insert to Slot 6.

After you change a Type-B or Type-D switching fabric module to a Type-A switching fabric module on the SR8804-X router, you must restart the router.

Compatibility information

Table2-541 Compatibility matrix between switching fabric modules and routers

Chassis model	Available switching fabric module model	Number
SR8804-X	Type-A: SFC-04-1, SFC-04-2, SFC-04-3, and SFC-04-4	4 (1 for each switching fabric module model)
SR8804-X	· Type-B: SFC-04B · Type-D: SFC-04D	2 to 4
SR8808-X	· Type-B: SFC-08B · Type-D: SFC-08D · Type-E: SFC-08E	2 to 4
SR8808H-X	· Type-E: SFC-08E1 · Type-T: SFC-08T · Type-TG: CSFC-08T-G	2 to 5
SR8812-X	· Type-B: SFC-12B · Type-D: SFC-12D · Type-E: SFC-12E	2 to 4
SR8816-X	· Type-E: SFC-16E · Type-T: SFC-16T, CSFC-16T3 · Type-TG: CSFC-16T-G	2 to 5

Table2-542 Compatibility matrix between switching fabric modules and service modules (1)

Service module	Type-A switching fabric module	SFC-04B	SFC-04D	SFC-08B	SFC-08D	SFC-12B SFC-12D
SPC-GT48LA1	Supported	Supported	Supported	Supported	Supported	Supported
CSPC-GE24L-E	Supported	Supported	Supported	Supported	Supported	Supported
SPC-GP24LA1	Supported	Supported	Supported	Supported	Supported	Supported
SPC-GP48LA1	Supported	Supported	Supported	Supported	Supported	Supported
SPC-GP48LB	Supported	Supported	Supported	Supported	Supported	Supported
SPC-GP24XP2LA	Supported	Supported	Supported	Supported	Supported	Supported
SPC-GP24XP2LB	Supported	Supported	Supported	Supported	Supported	Supported
CSPC-GP24GE8XP2L-E	Supported	Supported	Supported	Supported	Supported	Supported
CSPC-GE16XP4L-E	Supported	Supported	Supported	Supported	Supported	Supported
SPC-GP44XP4LAX	Not supported	Supported	Supported	Supported	Supported	Supported
SPC-GP44XP4LCX	Not supported	Supported	Supported	Supported	Supported	Supported
SPC-XP2LA1	Supported	Supported	Supported	Supported	Supported	Supported
SPC-XP4LA1	Supported	Supported	Supported	Supported	Supported	Supported
SPC-XP4LB	Supported	Supported	Supported	Supported	Supported	Supported
SPC-XP8LA	Supported	Supported	Supported	Supported	Supported	Supported
SPC-XP8LB	Supported	Supported	Supported	Supported	Supported	Supported
SPC-XP12LAX	Not supported	Supported	Supported	Supported	Supported	Supported
SPC-XP12LCX	Not supported	Supported	Supported	Supported	Supported	Supported
SPC-XP24LAX	Not supported	Supported	Supported	Supported	Supported	Supported
SPC-XP24LCX	Not supported	Supported	Supported	Supported	Supported	Supported
SPC-XLP6LAX	Not supported	Supported	Supported	Supported	Supported	Supported
SPC-XLP6LCX	Not supported	Supported	Supported	Supported	Supported	Supported
SPC-CP1LAX	Not supported	Supported	Supported	Supported	Supported	Supported
SPC-CP1LCX	Not supported	Supported	Supported	Supported	Supported	Supported
SPC-CP2LA	Not supported	Supported	Supported	Supported	Supported	Supported
SPC-CP2LB	Not supported	Supported	Supported	Supported	Supported	Supported
CEPC-XP4LX	Not supported	Supported	Supported	Supported	Supported	Supported
CEPC-XP24LX	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CEPC-XP48RX	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CEPC-CP4RX	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CEPC-CP4RX-L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CEPC-CQ8L	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CEPC-CQ16L1	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CEPC-DQ2L1-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
SPEX-1204	Supported	Supported	Supported	Supported	Supported	Supported
CSPEX-1104-E	Supported	Supported	Supported	Supported	Supported	Supported
CSPEX-1304X	Not supported	Supported	Supported	Supported	Supported	Supported
CSPEX-1404X	Not supported	Supported	Supported	Supported	Supported	Supported
CSPEX-1502X	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CSPEX-1504X	Not supported	Supported	Supported	Supported	Supported	Supported
CSPEX-1602X	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CSPEX-1802X	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CSPEX-1802XB	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CSPEX-1804X	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CSPEX-1512X	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CSPEX-1612X	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CSPEX-1812X	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CSPEX-1812X-E	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CSPEX-2304X-G	Not supported	Supported	Supported	Supported	Supported	Not supported
CSPEX-2304X-G2	Not supported	Supported	Supported	Supported	Supported	Supported
CSPEX-2304X-LG	Not supported	Supported	Supported	Supported	Supported	Not supported
CSPEX-2314X-G	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CSPEX-2314X-G1	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CSPEX-2314X-G2	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CSPEX-2612X-E	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
CSPEX-2612X3-E	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
MPE-1104	Supported	Supported	Supported	Supported	Supported	Supported
RX-SPE200	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
RX-SPE200-E	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
IM-NGFWX-IV	Not supported	Supported	Supported	Supported	Supported	Supported
LSU1FWCEA0	Supported	Supported	Supported	Supported	Supported	Supported
LSU3FWCEA0	Supported	Supported	Supported	Supported	Supported	Supported
IM-IPSX-IV	Not supported	Supported	Supported	Supported	Supported	Supported
LSU1IPSBEA0	Supported	Supported	Supported	Supported	Supported	Supported
IM-ACG1000X-IV	Not supported	Supported	Supported	Supported	Supported	Supported
LSU1ADECEA0	Supported	Supported	Supported	Supported	Supported	Supported
IM-APA-I	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
IM-APA-I3	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
IM-MSUX (1 U)	Not supported	Supported	Supported	Supported	Supported	Supported
IM-MSUX (1.2 U)	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
IM-MSEX-B	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
IM-MSEX-B3	Not supported	Not supported	Not supported	Not supported	Not supported	Not supported
IM-SMUX	Not supported	Supported	Supported	Supported	Supported	Not supported
IM-SFMX	Not supported	Supported	Supported	Supported	Supported	Supported
IM-OAPX	Not supported	Supported	Supported	Supported	Supported	Supported

Table2-543 Compatibility matrix between switching fabric modules and service modules (2)

Service module	SFC-08E	SFC-08E1	SFC-12E	SFC-08T	CSFC-08T-G
SPC-GT48LA1	Not supported	Not supported	Not supported	Not supported	Not supported
CSPC-GE24L-E	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-GP24LA1	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-GP48LA1	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-GP48LB	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-GP24XP2LA	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-GP24XP2LB	Not supported	Not supported	Not supported	Not supported	Not supported
CSPC-GP24GE8XP2L-E	Not supported	Not supported	Not supported	Not supported	Not supported
CSPC-GE16XP4L-E	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-GP44XP4LAX	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-GP44XP4LCX	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-XP2LA1	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-XP4LA1	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-XP4LB	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-XP8LA	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-XP8LB	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-XP12LAX	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-XP12LCX	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-XP24LAX	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-XP24LCX	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-XLP6LAX	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-XLP6LCX	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-CP1LAX	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-CP1LCX	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-CP2LA	Not supported	Not supported	Not supported	Not supported	Not supported
SPC-CP2LB	Not supported	Not supported	Not supported	Not supported	Not supported
CEPC-XP4LX	Supported	Supported	Supported	Supported	Supported
CEPC-XP24LX	Supported	Supported	Supported	Supported	Not supported
CEPC-XP48RX	Supported	Supported	Supported	Supported	Not supported
CEPC-CP4RX	Supported	Supported	Supported	Supported	Not supported
CEPC-CP4RX-L	Supported	Supported	Supported	Supported	Not supported
CEPC-CQ8L	Not supported	Not supported	Not supported	Supported	Not supported
CEPC-CQ16L1	Not supported	Not supported	Not supported	Supported	Not supported
CEPC-DQ2L1-G	Not supported	Not supported	Not supported	Supported	Not supported
SPEX-1204	Not supported	Not supported	Not supported	Not supported	Not supported
CSPEX-1104-E	Not supported	Not supported	Not supported	Not supported	Not supported
CSPEX-1304X	Supported	Supported	Supported	Supported	Supported
CSPEX-1404X	Supported	Supported	Supported	Supported	Supported
CSPEX-1502X	Supported	Supported	Supported	Supported	Not supported
CSPEX-1504X	Supported	Supported	Supported	Supported	Supported
CSPEX-1602X	Supported	Supported	Supported	Supported	Not supported
CSPEX-1802X	Not supported	Supported	Not supported	Supported	Supported
CSPEX-1802XB	Not supported	Supported	Not supported	Supported	Not supported
CSPEX-1804X	Not supported	Supported	Not supported	Supported	Supported
CSPEX-1512X	Not supported	Supported	Not supported	Supported	Supported
CSPEX-1612X	Not supported	Supported	Not supported	Supported	Supported
CSPEX-1812X	Not supported	Supported	Not supported	Supported	Supported
CSPEX-1812X-E	Not supported	Supported	Not supported	Supported	Supported
CSPEX-2304X-G	Supported	Supported	Not supported	Supported	Supported
CSPEX-2304X-G2	Supported	Supported	Supported	Supported	Supported
CSPEX-2304X-LG	Supported	Supported	Not supported	Supported	Supported
CSPEX-2314X-G	Not supported	Supported	Not supported	Supported	Supported
CSPEX-2314X-G1	Not supported	Supported	Not supported	Supported	Supported
CSPEX-2314X-G2	Not supported	Supported	Not supported	Supported	Supported
CSPEX-2612X-E	Not supported	Supported	Not supported	Supported	Supported
CSPEX-2612X3-E	Not supported	Supported	Not supported	Supported	Not supported
MPE-1104	Not supported	Not supported	Not supported	Not supported	Not supported
RX-SPE200	Not supported	Supported	Not supported	Supported	Supported
RX-SPE200-E	Not supported	Supported	Not supported	Supported	Supported
IM-NGFWX-IV	Supported	Supported	Supported	Supported	Supported
LSU1FWCEA0	Not supported	Not supported	Not supported	Not supported	Not supported
LSU3FWCEA0	Not supported	Not supported	Not supported	Not supported	Not supported
IM-IPSX-IV	Supported	Supported	Supported	Supported	Supported
LSU1IPSBEA0	Not supported	Not supported	Not supported	Not supported	Not supported
IM-ACG1000X-IV	Supported	Supported	Supported	Supported	Supported
LSU1ADECEA0	Not supported	Not supported	Not supported	Not supported	Not supported
IM-APA-I	Not supported	Supported	Not supported	Supported	Not supported
IM-APA-I3	Not supported	Supported	Not supported	Supported	Not supported
IM-MSUX (1 U)	Supported	Supported	Supported	Supported	Supported
IM-MSUX (1.2 U)	Not supported	Supported	Not supported	Supported	Not supported
IM-MSEX-B	Not supported	Supported	Not supported	Supported	Not supported
IM-MSEX-B3	Not supported	Supported	Not supported	Supported	Not supported
IM-SMUX	Not supported	Supported	Not supported	Supported	Supported
IM-SFMX	Supported	Supported	Supported	Not supported	Not supported
IM-OAPX	Supported	Supported	Supported	Supported	Supported

Table2-544 Compatibility matrix between switching fabric modules and service modules (3)

Service module	SFC-16E	SFC-16T	CSFC-16T3	CSFC-16T-G
SPC-GT48LA1	Not supported	Not supported	Not supported	Not supported
CSPC-GE24L-E	Not supported	Not supported	Not supported	Not supported
SPC-GP24LA1	Not supported	Not supported	Not supported	Not supported
SPC-GP48LA1	Not supported	Not supported	Not supported	Not supported
SPC-GP48LB	Not supported	Not supported	Not supported	Not supported
SPC-GP24XP2LA	Not supported	Not supported	Not supported	Not supported
SPC-GP24XP2LB	Not supported	Not supported	Not supported	Not supported
CSPC-GP24GE8XP2L-E	Not supported	Not supported	Not supported	Not supported
CSPC-GE16XP4L-E	Not supported	Not supported	Not supported	Not supported
SPC-GP44XP4LAX	Not supported	Not supported	Not supported	Not supported
SPC-GP44XP4LCX	Not supported	Not supported	Not supported	Not supported
SPC-XP2LA1	Not supported	Not supported	Not supported	Not supported
SPC-XP4LA1	Not supported	Not supported	Not supported	Not supported
SPC-XP4LB	Not supported	Not supported	Not supported	Not supported
SPC-XP8LA	Not supported	Not supported	Not supported	Not supported
SPC-XP8LB	Not supported	Not supported	Not supported	Not supported
SPC-XP12LAX	Not supported	Not supported	Not supported	Not supported
SPC-XP12LCX	Not supported	Not supported	Not supported	Not supported
SPC-XP24LAX	Not supported	Not supported	Not supported	Not supported
SPC-XP24LCX	Not supported	Not supported	Not supported	Not supported
SPC-XLP6LAX	Not supported	Not supported	Not supported	Not supported
SPC-XLP6LCX	Not supported	Not supported	Not supported	Not supported
SPC-CP1LAX	Not supported	Not supported	Not supported	Not supported
SPC-CP1LCX	Not supported	Not supported	Not supported	Not supported
SPC-CP2LA	Not supported	Not supported	Not supported	Not supported
SPC-CP2LB	Not supported	Not supported	Not supported	Not supported
CEPC-XP4LX	Supported	Supported	Not supported	Supported
CEPC-XP24LX	Supported	Supported	Not supported	Not supported
CEPC-XP48RX	Supported	Supported	Not supported	Not supported
CEPC-CP4RX	Supported	Supported	Not supported	Not supported
CEPC-CP4RX-L	Supported	Supported	Not supported	Not supported
CEPC-CQ8L	Not supported	Supported	Not supported	Not supported
CEPC-CQ16L1	Not supported	Supported	Not supported	Not supported
CEPC-DQ2L1-G	Not supported	Supported	Not supported	Not supported
SPEX-1204	Not supported	Not supported	Not supported	Not supported
CSPEX-1104-E	Not supported	Not supported	Not supported	Not supported
CSPEX-1304X	Supported	Supported	Not supported	Supported
CSPEX-1404X	Supported	Supported	Not supported	Supported
CSPEX-1502X	Supported	Supported	Not supported	Not supported
CSPEX-1504X	Supported	Supported	Not supported	Supported
CSPEX-1602X	Supported	Supported	Not supported	Not supported
CSPEX-1802X	Supported	Supported	Not supported	Not supported
CSPEX-1802XB	Supported	Supported	Supported	Not supported
CSPEX-1804X	Supported	Supported	Not supported	Supported
CSPEX-1512X	Supported	Supported	Not supported	Supported
CSPEX-1612X	Supported	Supported	Not supported	Supported
CSPEX-1812X	Supported	Supported	Not supported	Supported
CSPEX-1812X-E	Supported	Supported	Supported	Supported
CSPEX-2304X-G	Supported	Supported	Not supported	Supported
CSPEX-2304X-G2	Supported	Supported	Not supported	Supported
CSPEX-2304X-LG	Supported	Supported	Not supported	Supported
CSPEX-2314X-G	Supported	Supported	Not supported	Supported
CSPEX-2314X-G1	Supported	Supported	Not supported	Supported
CSPEX-2314X-G2	Supported	Supported	Not supported	Supported
CSPEX-2612X-E	Supported	Supported	Not supported	Not supported
CSPEX-2612X3-E	Supported	Supported	Supported	Not supported
MPE-1104	Not supported	Not supported	Not supported	Not supported
RX-SPE200	Supported	Supported	Not supported	Supported
RX-SPE200-E	Supported	Supported	Not supported	Not supported
IM-NGFWX-IV	Supported	Supported	Not supported	Supported
LSU1FWCEA0	Not supported	Not supported	Not supported	Not supported
LSU3FWCEA0	Not supported	Not supported	Not supported	Not supported
IM-IPSX-IV	Supported	Supported	Not supported	Supported
LSU1IPSBEA0	Not supported	Not supported	Not supported	Not supported
IM-ACG1000X-IV	Supported	Supported	Not supported	Supported
LSU1ADECEA0	Not supported	Not supported	Not supported	Not supported
IM-APA-I	Supported	Supported	Supported	Not supported
IM-APA-I3	Supported	Supported	Supported	Not supported
IM-MSUX (1 U)	Supported	Supported	Supported	Supported
IM-MSUX (1.2 U)	Supported	Supported	Supported	Not supported
IM-MSEX-B	Supported	Supported	Supported	Not supported
IM-MSEX-B3	Supported	Supported	Supported	Not supported
IM-SMUX	Supported	Supported	Supported	Supported
IM-SFMX	Supported	Not supported	Not supported	Not supported
IM-OAPX	Supported	Supported	Not supported	Supported

Power supplies

The router supports the PSR1200B-12A, PSR1200B-12A1-F, LSUM1AC1200, LSUM1AC2500, PSR2500-12A, LSUM1DC2400, PSR2400-12D, PSR2400-D, and PSR2500B-12AHD-F power supplies.

PSR1200B-12A/LSUM1AC1200

View

Figure2-153 PSR1200B-12A view

(1) Captive screw	(2) Power supply handle
(3) Power input receptacle	(4) Air inlet vent
(5) Power output status LED	(6) Power input status LED

NOTE:

The views of the PSR1200B-12A and LSUM1AC1200 power supplies are similar. This figure uses the PSR1200B-12A as an example.

LEDs

Table2-545 PSR1200B-12A/LSUM1AC1200 LED description

LED mark	Status	Description
AC	Steady green	The power supply is operating correctly.
	Off	No power input.
	Off	The input voltage is too low and the power supply has entered self-protection state.
DC	Steady green	Power output of the power supply is normal.
	Steady red	Power output of the power supply is abnormal. The power supply has an output short circuit, output overcurrent, output overvoltage, input undervoltage, or remote shutdown alarm and has entered self-protection state.
	Steady amber	An overtemperature alarm is present.

Technical specifications

Table2-546 Technical specifications

Item	Description
Dimensions (H × W × D)	41 × 102 × 410 mm (1.61 × 4.02 × 16.14 in)
Weight	2.27 kg (5.00 lb)
Inputs	1
Rated input voltage range	100 VAC to 240 VAC @ 50 Hz or 60 Hz
Input voltage range	90 VAC to 290 VAC
Maximum input current	16 A
Rated output voltage	12 VDC
Rated output current	100 A
Rated output power	1200 W
Front-level circuit breaker/fuse	≥ 20 A
Heat dissipation	Built-in fans
Power cable	Standard C19 cable (3*1.5mm²)

PSR1200B-12A1-F

View

Figure2-154 PSR1200B-12A1-F power supply view

(1) Captive screw	(2) Power supply handle
(3) Power input receptacle	(4) Air inlet vent
(5) Power output status LED	(6) Power input status LED

LEDs

Table2-547 PSR1200B-12A1-F LED description

LED mark	Status	Description
AC	Steady green	The power supply is operating correctly.
	Off	No power input.
	Off	The input voltage is too low and the power supply has entered self-protection state.
DC	Steady green	Normal power output.
	Steady red	Power output of the power supply is abnormal. The power supply has an output short circuit, output overcurrent, output overvoltage, input undervoltage, or remote shutdown alarm and has entered self-protection state.
	Steady amber	An overtemperature alarm is present.

Technical specifications

Table2-548 Technical specifications

Item	Description
Dimensions (H × W × D)	41 × 102 × 410 mm (1.61 × 4.02 × 16.14 in)
Weight	2.27 kg (5.00 lb)
Inputs	1
Rated input voltage range	· 200 VAC to 240 VAC @ 50 Hz or 60 Hz · 240 VDC
Input voltage range	· 180 VAC to 264 VAC · 192 VDC to 320 VDC
Maximum input current	10 A
Rated output voltage	12 VDC
Rated output current	100 A
Rated output power	1200 W
Front-level circuit breaker/fuse	≥ 20 A
Heat dissipation	Built-in fans
Power cable	Standard C13 cable (3*1.0mm²)

PSR2500-12A/LSUM1AC2500

View

Figure2-155 PSR2500-12A view

(1) Captive screw	(2) Power supply handle
(3) Power input receptacle	(4) Air inlet vent
(5) Power output status LED	(6) Power input status LED

NOTE:

The views of the PSR2500-12A and LSUM1AC2500 power supplies are similar. This figure uses the PSR2500-12A as an example.

LEDs

Table2-549 PSR2500-12A/LSUM1AC2500 LED description

LED mark	Status	Description
AC	Steady green	The power supply is operating correctly.
	Off	No power input.
	Off	The input voltage is too low and the power supply has entered self-protection state.
DC	Steady green	Power output of the power supply is normal.
	Steady red	Power output of the power supply is abnormal. The power supply has an output short circuit, output overcurrent, output overvoltage, input undervoltage, or remote shutdown alarm and has entered self-protection state.
	Steady amber	An overtemperature alarm is present.

Technical specifications

Table2-550 Technical specifications

Item	Description
Dimensions (H × W × D)	41 × 102 × 410 mm (1.61 × 4.02 × 16.14 in)
Weight	2.50 kg (5.51 lb)
Inputs	1
Rated input voltage range	· 100 VAC to 240 VAC @ 50 Hz or 60 Hz · 240 VDC
Input voltage range	· 90 VAC to 264 VAC · 190 VDC to 290 VDC
Maximum input current	16 A
Rated output voltage	12 VDC
Rated output current	· 100 A (100 VAC to 180 VAC input) · 208 A (180 VAC to 240 VAC or 240 VDC input)
Rated output power	· 1200 W (100 VAC to 180 VAC input) · 2500 W (180 VAC to 240 VAC or 240 VDC input)
Front-level circuit breaker/fuse	≥ 20 A
Heat dissipation	Built-in fans
Power cable	Standard C19 cable (3*1.5mm²)

PSR2400-12D/LSUM1DC2400

View

Figure2-156 PSR2400-12D view

(1) Captive screw	(2) Power supply handle
(3) Power input status LED	(4) Power output status LED
(5) DC input negative terminal (–)	(6) DC input positive terminal (+)

NOTE:

The views of the PSR2400-12D and LSUM1DC2400 power supplies are similar. This figure uses the PSR2400-12D as an example.

LEDs

Table2-551 PSR2400-12D/LSUM1DC2400 LED description

LED mark	Status	Description
INP OK	Steady green	The power supply is operating correctly.
	Off	No power input.
	Off	The input voltage is too low and the power supply has entered self-protection state.
DC/FLT	Steady green	Power output of the power supply is normal.
	Steady red	Power output of the power supply is abnormal. The power supply has an output short circuit, output overcurrent, output overvoltage, input undervoltage, or remote shutdown alarm and has entered self-protection state.
	Steady amber	An overtemperature alarm is present.

Technical specifications

Table2-552 Technical specifications

Item	Description
Dimensions (H × W × D)	41 × 102 × 410 mm (1.61 × 4.02 × 16.14 in)
Weight	2.40 kg (5.29 lb)
Inputs	1
Rated input voltage range	–48 VDC to –60 VDC
Input voltage range	–36 VDC to –72 VDC
Maximum input current	78 A
Rated output voltage	12 VDC
Rated output current	200 A
Rated output power	2400 W
Front-level circuit breaker/fuse	≥ 100 A
Heat dissipation	Built-in fans
Power cable	PWC01 2P cable

PSR2400-D

View

Figure2-157 PSR2400-D view

(1) Captive screw	(2) Power supply handle
(3) Power input status LED	(4) Power output status LED
(5) DC input negative terminal (–)	(6) DC input positive terminal (+)

LEDs

Table2-553 PSR2400-D LED description

LED mark	Status	Description
INP OK	Steady green	The power supply is operating correctly.
	Off	No power input.
	Off	The input voltage is too low and the power supply has entered self-protection state.
DC/FLT	Steady green	Power output of the power supply is normal.
	Steady red	Power output of the power supply is abnormal. The power supply has an output short circuit, output overcurrent, output overvoltage, input undervoltage, or remote shutdown alarm and has entered self-protection state.
	Steady amber	An overtemperature alarm is present.

Technical specifications

Table2-554 Technical specifications

Item	Description
Dimensions (H × W × D)	41 × 102 × 410 mm (1.61 × 4.02 × 16.14 in)
Weight	2.40 kg (5.29 lb)
Inputs	1
Rated input voltage range	–48 VDC to –60 VDC
Input voltage range	–36 VDC to –72 VDC
Maximum input current	78 A
Rated output voltage	12 VDC
Rated output current	200 A
Rated output power	2400 W
Front-level circuit breaker/fuse	≥ 100 A
Heat dissipation	Built-in fans
Power cable	ST M5 cable

PSR2500B-12AHD-F

View

Figure2-158 PSR2500B-12AHD-F view

(1) Captive screw	(2) Power supply handle
(3) Power input receptacle	(4) Power output status LED
(5) Power input status LED	(6) Air inlet vent

LEDs

Table2-555 PSR2500B-12AHD-F LED description

LED mark	Status	Description
IN	Steady green	The power supply is operating correctly.
	Off	No power input.
	Off	The input voltage is too low and the power supply has entered self-protection state.
OUT	Steady green	Power output of the power supply is normal.
	Steady red	Power output of the power supply is abnormal. The power supply has an output short circuit, output overcurrent, output overvoltage, input undervoltage, or remote shutdown alarm and has entered self-protection state.
	Steady amber	An overtemperature alarm is present.

Technical specifications

Table2-556 Technical specifications

Item	Description
Dimensions (H × W × D)	41 × 102 × 410 mm (1.61 × 4.02 × 16.14 in)
Weight	2.75 kg (6.06 lb)
Inputs	1
Rated input voltage range	· 100 VAC to 240 VAC @ 50 Hz or 60 Hz · 240 VDC to 380 VDC
Input voltage range	· 90 VAC to 290 VAC · 180 VDC to 400 VDC
Maximum input current	16 A
Rated output voltage	12 VDC
Rated output current	· 100 A (100 VAC to 180 VAC input) · 208 A (180 VAC to 240 VAC or 240 VDC to 380 VDC input)
Rated output power	· 1200 W (100 VAC to 180 VAC input) · 2500 W (180 VAC to 240 VAC or 240 VDC to 380 VDC input)
Front-level circuit breaker/fuse	≥ 20 A
Heat dissipation	Built-in fans
Power cable	Standard HVDCB cable (3*1.5mm²)

PSR2200-12D-F

View

Figure2-159 PSR2200-12D-F power supply view

(1) Captive screw	(2) Power supply handle
(3) Power input status LED	(4) Power output status LED
(5) DC input positive terminal (+)	(6) DC input negative terminal (–)
(7) Air inlet vent

LEDs

Table2-557 PSR2200-12D-F LED description

LED mark	Status	Description
INP OK	Steady green	The power supply system is operating correctly.
	Off	No power input.
	Off	The input voltage is too low and the power supply has entered self-protection state.
DC/FLT	Steady green	Power output of the power supply system is normal.
	Steady red	Power output of the power supply system is abnormal. The power supply has an output short circuit, output overcurrent, output overvoltage, input undervoltage, or remote shutdown alarm and has entered self-protection state.
	Steady amber	An overtemperature alarm was triggered.

Technical specifications

Table2-558 Technical specifications

Item	Description
Dimensions (H × W × D)	41 × 102 × 410 mm (1.61 × 4.02 × 16.14 in)
Weight	1.78 kg (3.92 lb)
Inputs	1
Rated input voltage range	–48 VDC to –60 VDC
Input voltage range	–38.4 VDC to –72 VDC
Maximum input current	70 A
Rated output voltage	12 VDC
Rated output current	184 A
Rated output power	2200 W
Front-level circuit breaker/fuse	≥ 100 A
Heat dissipation	Built-in fans
Power cable	ST M5 cable

PSR2400-12A-F

View

Figure2-160 PSR2400-12A-F power supply view

(1) Captive screw	(2) Power supply handle
(3) Power input receptacle	(4) Air inlet vent
(5) Power output status LED	(6) Power input status LED

LEDs

Table2-559 PSR2400-12A-F LED description

LED mark	Status	Description
AC	Steady green	The power supply system is operating correctly.
	Off	No power input.
	Off	The input voltage is too low and the power supply has entered self-protection state.
DC	Steady green	Power output of the power supply system is normal.
	Steady red	Power output of the power supply system is abnormal. The power supply has an output short circuit, output overcurrent, output overvoltage, input undervoltage, or remote shutdown alarm and has entered self-protection state.
	Steady amber	An overtemperature alarm was triggered.

Technical specifications

Table2-560 Technical specifications

Item	Description
Dimensions (H × W × D)	41 × 102 × 410 mm (1.61 × 4.02 × 16.14 in)
Weight	2.20 kg (4.85 lb)
Inputs	1
Rated input voltage range	· 100 VAC to 240 VAC @ 50 Hz or 60 Hz · 240 VDC
Input voltage range	· 90 VAC to 290 VAC · 180 VDC to 320 VDC
Maximum input current	16 A
Rated output voltage	12 VDC
Rated output current	· 100 A (100 VAC to 175 VAC input) · 200 A (175 VAC to 240 VAC or 240 VDC input)
Rated output power	· 1200 W (100 VAC to 175 VAC input) · 2400 W (175 VAC to 240 VAC or 240 VDC input)
Front-level circuit breaker/fuse	≥ 32 A
Heat dissipation	Built-in fans
Power cable	Standard C19 cable (3*1.5mm²)

PSR2400-12AHD-F

View

Figure2-161 PSR2400-12AHD-F power supply view

(1) Captive screw	(2) Power supply handle
(3) Power input receptacle	(4) Air inlet vent
(5) Power output status LED	(6) Power input status LED

LEDs

Table2-561 PSR2400-12AHD-F LED description

LED mark	Status	Description
IN	Steady green	The power supply system is operating correctly.
	Off	No power input.
	Off	The input voltage is too low and the power supply has entered self-protection state.
OUT	Steady green	Power output of the power supply system is normal.
	Steady red	Power output of the power supply system is abnormal. The power supply has an output short circuit, output overcurrent, output overvoltage, input undervoltage, or remote shutdown alarm and has entered self-protection state.
	Steady amber	An overtemperature alarm was triggered.

Technical specifications

Table2-562 Technical specifications

Item	Description
Dimensions (H × W × D)	41 × 102 × 410 mm (1.61 × 4.02 × 16.14 in)
Weight	2.20 kg (4.85 lb)
Inputs	1
Rated input voltage range	· 100 VAC to 240 VAC @ 50 Hz or 60 Hz · 240 VDC to 380 VDC
Input voltage range	· 90 VAC to 290 VAC · 180 VDC to 410 VDC
Maximum input current	16 A
Rated output voltage	12 VDC
Rated output current	· 100 A (100 VAC to 175 VAC input) · 200 A (175 VAC to 240 VAC or 240 VDC to 380 VDC input)
Rated output power	· 1200 W (100 VAC to 175 VAC input) · 2400 W (175 VAC to 240 VAC or 240 VDC to 380 VDC input)
Front-level circuit breaker/fuse	≥ 32 A
Heat dissipation	Built-in fans
Power cable	Standard HVDCB cable (3*1.5mm²)

Configuration restrictions and guidelines

As a best practice, make sure the rated current of a single circuit breaker is not less than 1.2 times the maximum input current of the power supply.

You can select a certain number of power supplies according to the power supply conditions at the installation site and actual power consumption of your router. Make sure the total maximum output power of the installed power supplies is greater than the system power consumption. As a best practice, reserve 20% of the maximum output power.

Do not install power supplies of different models on the same router.

When the temperature of a power supply exceeds the upper limit or drops below the lower limit, the power supply shuts down automatically. When the temperature returns into the normal range, the power supply starts up automatically.

Compatibility information

Table2-563 Compatibility matrix between power supplies and routers

Power supply model	SR8804-X	SR8808-X (one fan tray)/SR8808-X (dual fan trays)	SR8808H-X	SR8812-X	SR8816-X
LSUM1AC1200	●	●	●	●	●
PSR1200B-12A	●	●	●	●	●
PSR1200B-12A1-F	●	●	●	●	●
LSUM1AC2500	●	●	●	●	●
PSR2500-12A	●	●	●	●	●
LSUM1DC2400	●	●	●	●	●
PSR2400-12D	●	●	●	●	●
PSR2400-D	●	●	●	●	●
PSR2500B-12AHD-F	●	●	●	●	●
PSR2200-12D-F	—	—	●	—	●
PSR2400-12A-F	—	—	●	—	●
PSR2400-12AHD-F	—	—	●	—	●

NOTE:

· "●" indicates that the power supply is compatible with the chassis.

· "—" indicates that the power supply is not compatible with the chassis.

Fan trays

The router came with fan trays installed. To replace a fan tray, make sure the new fan tray is compatible with the router.

SR8804-X fan tray

View

Figure2-162 SR8804-X fan tray view

(1) Captive screw	(2) Status LED
(3) Fan tray handle	(4) Fan tray handle pivot
(5) Fan

LEDs

Table2-564 Fan tray LED description

LED status		Description
OK	FAIL	Description
Steady on	Off	The fan tray is operating correctly.
Off	Steady on	The fan tray is faulty.
Off	Off	The fan tray has not been powered on.

Technical specifications

Table2-565 Technical specifications

Item	Description
Dimensions (H × W × D)	106 × 255 × 643 mm (4.17 × 10.04 × 25.32 in)
Weight	4.70 kg (10.36 lb)
Maximum power consumption	240 W
Typical power consumption	190 W
Minimum power consumption	12 W
Number of fans	8
Fan diameter	92 mm (3.62 in)
Max fan speed	6000 RPM
Maximum air flow rate	960 CFM (27.18 m3/min)

SR8808-X (one fan tray) fan tray

View

Figure2-163 SR8808-X (one fan tray) fan tray view

(1) Fan	(2) Status LED
(3) Captive screw	(4) Fan tray handle
(5) Fan tray handle pivot

LEDs

Table2-566 Fan tray LED description

LED status		Description
OK	FAIL	Description
Steady on	Off	The fan tray is operating correctly.
Off	Steady on	The fan tray is faulty.
Off	Off	The fan tray has not been powered on.

Technical specifications

Table2-567 Technical specifications

Item	Description
Dimensions (H × W × D)	80 × 440 × 654 mm (3.15 × 17.32 × 25.75 in)
Weight	8.30 kg (18.30 lb)
Maximum power consumption	300 W
Typical power consumption	260 W
Minimum power consumption	13 W
Number of fans	12
Fan diameter	120 mm (4.72 in)
Max fan speed	5200 RPM
Maximum air flow rate	1152 CFM (32.62 m3/min)

SR8808-X (dual fan trays) fan tray

View

Figure2-164 SR8808-X (dual fan trays) fan tray view

(1) Fan	(2) Status LED
(3) Captive screw	(4) Fan tray handle
(5) Fan tray handle pivot

LEDs

Table2-568 Fan tray LED description

LED status		Description
OK	FAIL	Description
Steady on	Off	The fan tray is operating correctly.
Off	Steady on	The fan tray is faulty.
Off	Off	The fan tray has not been powered on.

Technical specifications

The SR8808-X (dual fan trays) has two fan trays, which are the same in technical specifications. Table2-569 describes the specifications for a single SR8808-X (dual fan trays) fan tray.

Table2-569 Single SR8808-X (dual fan trays) fan tray specifications

Item	Description
Dimensions (H × W × D)	49 × 440 × 654 mm (1.93 × 17.32 × 25.75 in)
Weight	7.40 kg (16.31 lb)
Maximum power consumption	320 W
Typical power consumption	63 W
Minimum power consumption	18 W
Number of fans	12
Fan diameter	120 mm (4.72 in)
Max fan speed	5200 RPM
Maximum air flow rate	1152 CFM (32.62 m3/min)

SR8808H-X/SR8816-X fan tray

View

Figure2-165 SR8808H-X fan tray view

(1) Captive screw	(2) Status LED
(3) Fan tray handle	(4) Fan

NOTE:

The views of the SR8808H-X fan tray and SR8816-X fan tray are similar. This figure uses the SR8808H-X fan tray as an example.

LEDs

Table2-570 Fan tray LED description

LED mark	Status	Description
RUN	Steady green	The fan tray is operating correctly.
	Steady red	· The fan tray is faulty. · The fan tray is installed incorrectly.
	Off	The fan tray has not been powered on.

Technical specifications

The SR8808H-X router has eight fan trays, and the SR8816-X router has fifteen fan trays, which are the same in technical specifications. Table2-571 describes the technical specifications of a single SR8808H-X router fan tray.

Table2-571 Single SR8808H-X router fan tray technical specifications

Item	Description
Dimensions (H × W × D)	191 × 81 × 159 mm (7.52 × 3.19 × 6.26 in)
Weight	1.35 kg (2.98 lb)
Maximum power consumption	143 W
Typical power consumption	114 W
Minimum power consumption	18 W
Number of fans	2
Fan diameter	80 mm (3.15 in)
Max fan speed	12800 RPM
Maximum air flow rate	350 CFM (9.91 m3/min)

SR8812-X fan tray

View

Figure2-166 SR8812-X fan tray view

(1) Captive screw	(2) Status LED
(3) Fan tray handle	(4) Fan tray handle pivot
(5) Fan

LEDs

Table2-572 Fan tray LED description

LED status		Description
OK	FAIL	Description
Steady on	Off	The fan tray is operating correctly.
Off	Steady on	The fan tray is faulty.
Off	Off	The fan tray has not been powered on.

Technical specifications

Table2-573 Technical specifications

Item	Description
Dimensions (H × W × D)	84 × 301 × 646 mm (3.31 × 11.85 × 25.43 in)
Weight	· Upper fan tray: 4.49 kg (9.90 lb) · Lower fan tray: 3.61 kg (7.96 lb)
Maximum power consumption	· Upper fan tray: 190 W · Lower fan tray: 110 W
Typical power consumption	· Upper fan tray: 160 W · Lower fan tray: 100 W
Minimum power consumption	· Upper fan tray: 9 W · Lower fan tray: 7 W
Number of fans	· Upper fan tray: 8 · Lower fan tray: 4
Fan diameter	120 mm (4.72 in)
Max fan speed	5200 RPM
Maximum air flow rate	· Upper fan tray: 1040 CFM (29.45 m3/min) · Lower fan tray: 720 CFM (20.39 m3/min)

Air filters

CAUTION:

Clean air filters periodically (once or more times every three months) to guarantee adequate ventilation and to avoid overtemperature.

To prevent dusts from entering the chassis, you can configure air filters for the router as needed and install them at the air intakes.

H3C SR8800-X air filters include the SR8804-X air filter, SR8808-X air filter, and SR8812-X air filter. Order air filters compatible with your router.

Slide rails

Before rack-mounting the router, install slide rails on the rack.

LSXM1BSR

Views

Figure2-167 LSXM1BSR view

(1) Positioning tongue	(2) Slide rail installation hole
(3) Front plate installation hole	(4) Sign
(5) Guide rail

Figure2-168 Front plate

(1) Installation hole

Technical specifications

Table2-574 Technical specifications

Item	Description
Maximum loading capacity	650 kg (1432.98 lb)
Adjustment range	630 to 900 mm (24.80 to 35.43 in)
Occupied rack space	1 RU

LSTM1KSGD0

Views

Figure2-169 LSTM1KSGD0 view

(1) Installation hole	(2) Sign
(3) Guide rail

Technical specifications

Table2-575 Technical specifications

Item	Description
Maximum loading capacity	280 kg (617.28 lb)
Adjustment range	300 to 500 mm (11.81 to 19.69 in)
Occupied rack space	2 RU

LSTM2KSGD0

Views

Figure2-170 LSTM2KSGD0 view

(1) Installation hole	(2) Sign
(3) Guide rail

Technical specifications

Table2-576 Technical specifications

Item	Description
Maximum loading capacity	400 kg (881.83 lb)
Adjustment range	500 to 800 mm (19.69 to 31.50 in)
Occupied rack space	2 RU

Configuration restrictions and guidelines

Select slide rails for the router based on the chassis weight.

To rack-mount an SR8816-X router, reserve a 2 RU space between the router (including slide rails) and the rack bottom.

Compatibility information

Table2-577 Chassis weights and applicable slide rails

Model	Chassis weight (fully configured)	Applicable slide rails
SR8804-X	76 kg (167.55 lb)	LSXM1BSR LSTM1KSGD0 LSTM2KSGD0
SR8808-X (one fan tray)	120 kg (264.55 lb)	LSXM1BSR LSTM1KSGD0 LSTM2KSGD0
SR8808-X (dual fan trays)	170 kg (374.78 lb)	LSXM1BSR LSTM1KSGD0 LSTM2KSGD0
SR8808H-X	245 kg (540.12 lb)	LSXM1BSR LSTM1KSGD0 LSTM2KSGD0
SR8812-X	174 kg (383.60 lb)	LSXM1BSR LSTM1KSGD0 LSTM2KSGD0
SR8816-X	440 kg (970.02 lb)	LSXM1BSR LSTM2KSGD0

DC power cords

DC power cords are used for connecting the DC power supplies of an SR8800-X router to the external DC power supply system.

Table2-578 DC power cord specifications

DC power cord	Cable length	Description
0404A0E1	3 m (9.84 ft)	Used for connecting the LSUM1DC2400/PSR2400-12D power supply
0404A0H8	3 m (9.84 ft)
0404A0E2	15 m (49.21 ft)
0404A0H9	15 m (49.21 ft)
0404A1BE	20 m (65.62 ft)
0404A1BF	20 m (65.62 ft)
0404A0J5	30 m (98.43 ft)
0404A1BD	40 m (131.23 ft)
0404A1M7	10 m (32.81 ft)	Used for connecting the PSR2400-D power supply
0404A1M6	15 m (49.21 ft)
0404A1M5	20 m (65.62 ft)
0404A1MD	30 m (98.43 ft)

AC power cords

AC power cords are used for connecting the AC power supplies of an SR8800-X router to the external AC power supply system.

To select an AC power cord for an AC power supply, consider the following items:

· Power capacity of the power supply.

· Current-carrying capacity of the power cord.

· Region-and country-specific plug type.

The AC power supplies available for the router require a 16A or 10A AC power cord. Table2-579 and Table2-580 describe the region-and country-specific plug types for 10A and 16A AC power cords, respectively.

Table2-579 10A AC power cords used in different countries or regions

1	Plug type			Code (Length)	Countries or regions where the type of power cords conforms to local safety regulations and can be used legally			Other countries or regions using this type of power cords	Countries or regions seldom using this type of power cords
	I type			04041104: 3 m (9.8 ft)	Mainland China			N/A	N/A
	Plug outline				Power cord outline				Connector outline

2	Plug type		Code (Length)		Countries or regions where the type of power cords conforms to local safety regulations and can be used legally		Other countries or regions using this type of power cords		Countries or regions seldom using this type of power cords
	B type		04020728: 3 m (9.8 ft)		Canada and U.S.A		Mexico, Argentina, Brazil, Columbia, Venezuela, Thailand, Peru, Philippine, and A6 countries or regions		N/A
	Plug outline				Power cord outline				Connector outline

3	Plug type		Code (Length)		Countries or regions where the type of power cords conforms to local safety regulations and can be used legally		Other countries or regions using this type of power cords		Countries or regions seldom using this type of power cords
	F type		04041056: 3 m (9.8 ft)		Holland, Denmark, Sweden, Finland, Norway, Germany, France, Austria, Belgium, and Italy		Indonesia, Türkiye, Russia, and CIS		N/A
	Plug outline				Power cord outline				Connector outline

4	Plug type		Code (Length)		Countries or regions where the type of power cords conforms to local safety regulations and can be used legally		Other countries or regions using this type of power cords		Countries or regions seldom using this type of power cords
	G type		04040890: 3 m (9.8 ft)		United Kingdom		Malaysia, Hong Kong, and Egypt		N/A
	Connector outline				Power cord outline				Connector outline

5	Plug type		Code (Length)		Countries or regions where the type of power cords conforms to local safety regulations and can be used legally		Other countries or regions using this type of power cords		Countries or regions seldom using this type of power cords
	B type		04040887: 3 m (9.8 ft)		Japan		N/A		N/A
	Plug outline				Power cord outline				Connector outline

6	Plug type	Code (Length)			Countries or regions where the type of power cords conforms to local safety regulations and can be used legally	Other countries or regions using this type of power cords			Countries or regions seldom using this type of power cords
	I type	04040888: 3 m (9.8 ft)			Australia	N/A			N/A
	Plug outline				Power cord outline				Connector outline

7	Plug type	Code (Length)			Countries or regions where the type of power cords conforms to local safety regulations and can be used legally	Other countries or regions using this type of power cords			Countries or regions seldom using this type of power cords
	J type	04041119: 3 m (9.8 ft)			Switzerland	N/A			N/A
	Plug outline				Power cord outline				Connector outline

8	Plug type	Code (Length)			Countries or regions where the type of power cords conforms to local safety regulations and can be used legally	Other countries or regions using this type of power cords			Countries or regions seldom using this type of power cords
	L type	04041120: 3 m (9.8 ft)			Italy	N/A			N/A
	Plug outline				Power cord outline				Connector outline

9	Plug type	Code (Length)			Countries or regions where the type of power cords conforms to local safety regulations and can be used legally	Other countries or regions using this type of power cords			Countries or regions seldom using this type of power cords
	D type	0404A0Q0: 3 m (9.8 ft)			India	N/A			N/A
	Plug outline				Power cord outline				Connector outline

Table2-580 16A AC power cords used in different countries or regions

1	Plug type			Code (Length)	Countries or regions where the type of power cords conforms to local safety regulations and can be used legally			Other countries or regions using this type of power cords	Countries or regions seldom using this type of power cords
	I type			04043396: 3 m (9.8 ft)	Mainland China			N/A	N/A
	Plug outline				Power cord outline				Connector outline

2	Plug type			Code (Length)	Countries or regions where the type of power cords conforms to local safety regulations and can be used legally			Other countries or regions using this type of power cords	Countries or regions seldom using this type of power cords
	C20 type			0404A0C2: 3 m (9.8 ft)	Mainland China			N/A	N/A
	Plug outline				Power cord outline				Connector outline

3	Plug type		Code (Length)		Countries or regions where the type of power cords conforms to local safety regulations and can be used legally	Other countries or regions using this type of power cords			Countries or regions seldom using this type of power cords
	B type		0404A063: 3 m (9.8 ft)		Canada and U.S.A	Mexico, Argentina, Brazil, Columbia, Venezuela, Thailand, Peru, Philippine, and A6 countries or regions			N/A
	Plug outline				Power cord outline				Connector outline

4	Plug type		Code (Length)		Countries or regions where the type of power cords conforms to local safety regulations and can be used legally	Other countries or regions using this type of power cords			Countries or regions seldom using this type of power cords
	F type		0404A061: 3 m (9.8 ft)		Holland, Denmark, Sweden, Finland, Norway, Germany, France, Austria, Belgium, and Italy	Indonesia, Türkiye, Russia, and CIS			N/A
	Plug outline				Power cord outline				Connector outline

5	Plug type		Code (Length)		Countries or regions where the type of power cords conforms to local safety regulations and can be used legally	Other countries or regions using this type of power cords			Countries or regions seldom using this type of power cords
	B type		0404A062: 3 m (9.8 ft)		Japan	N/A			N/A
	Connector outline				Power cord outline				Connector outline

6	Plug type		Code (Length)		Countries or regions where the type of power cords conforms to local safety regulations and can be used legally	Other countries or regions using this type of power cords			Countries or regions seldom using this type of power cords
	I type		0404A01A: 3 m (9.8 ft)		Australia	N/A			N/A
	Plug outline				Power cord outline				Connector outline

7	Plug type	Code (Length)			Countries or regions where the type of power cords conforms to local safety regulations and can be used legally		Other countries or regions using this type of power cords		Countries or regions seldom using this type of power cords
	I type	0404A0RQ: 3 m (9.8 ft)			Mainland China		N/A		N/A
	Plug outline				Power cord outline				Connector outline

H3C SR8800-X Router Series Hardware Information and Specifications-5W102

View

LEDs

Ports

Console port

Management Ethernet port

USB port

Technical specifications

View

LEDs

Ports

Console port

Management Ethernet port

USB port

SMB coaxial clock input/output port

Technical specifications

View

LEDs

Ports

Console port

Management Ethernet port

USB port

SMB coaxial clock input/output port

Technical specifications

View

LEDs

Ports

Console port

Management Ethernet port

USB port

SMB coaxial clock input/output port

High-precision time synchronization port

Technical specifications

View

LEDs

Ports

Console port

Management Ethernet port

USB port

CF card slot

Technical specifications

View

LEDs

Ports

Console port

Management Ethernet port

USB port

CF card slot

SMB coaxial clock input/output port

Technical specifications

View

LED

Ports

Console port

Management Ethernet port

USB port

CF card slot

SMB coaxial clock input/output port

Technical specifications

SPC/CSPC LPUs (interface modules)

View

LEDs

Ports

Technical specifications

View

LEDs

Ports

Technical specifications

View

LEDs

Ports

Technical specifications

View

LEDs

Ports

Technical specifications

View

LEDs

Ports

Technical specifications