Use area-authentication send-only to configure IS-IS not to check the authentication information in the received Level-1 packets, including LSPs, CSNPs, and PSNPs.

Use undo area-authentication send-only to restore the default.

Syntax

area-authentication send-only

undo area-authentication send-only

Default

When area authentication mode and key are configured, a Level-1 or Level-1-2 device checks the authentication information in the received packets.

Views

IS-IS view

Predefined user roles

network-admin

Usage guidelines

When area authentication mode and key are configured, a Level-1 or Level-1-2 device adds the key in the specified mode into transmitted Level-1 packets (including LSPs, CSNPs, and PSNPs). It also checks the key in the received Level-1 packets.

To prevent packet exchange failure in case of an authentication key change, configure IS-IS not to check the authentication information in the received packets.

Examples

# Configure IS-IS not to check the authentication information in the received packets.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] area-authentication send-only

Related commands

area-authentication-mode

domain-authentication send-only

isis authentication send-only

advertise link-attributes

Use advertise link-attributes to enable IS-IS to advertise link attributes in LSPs.

Use undo advertise link-attributes to restore the default.

NOTE:

This command is supported only in R3608 and later.

Syntax

advertise link-attributes

undo advertise link-attributes

Default

IS-IS does not advertise link attributes in LSPs.

Views

IS-IS IPv4 address family view

IS-IS IPv6 address family view

Predefined user roles

network-admin

Usage guidelines

Link attributes advertised in LSPs include the following:

· IP address.

· Link delay information. (The attribute is included after you enable link delay advertisement by using the metric-delay advertisement enable command.)

· Link bandwidth information. (The attribute is included after you enable link bandwidth advertisement by using the metric-bandwidth advertisement enable command.)

Multiple P2P neighbors might exist between two devices. To ensure correct route calculation, configure each device to advertise IP address of the local interface to its neighbors by using the advertise link-attributes or router-id command.

You can execute this command only when the link cost style is wide, compatible or wide-compatible.

Examples

# Enable IS-IS process 1 to advertise link attributes in LSPs.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] advertise link-attributes

Related commands

cost-style

metric-bandwidth advertisement enable

metric-delay advertisement enable

router-id (Segment Routing Command Reference)

area-authentication-mode

Use area-authentication-mode to specify an area authentication mode and a key.

Use undo area-authentication-mode to restore the default.

Syntax

area-authentication-mode { { gca key-id { hmac-sha-1 | hmac-sha-224 | hmac-sha-256 | hmac-sha-384 | hmac-sha-512 } [ nonstandard ] | md5 | simple } { cipher | plain } string | keychain keychain-name } [ ip | osi ]

undo area-authentication-mode

Default

No area authentication mode or key is configured.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

gca: Specifies the Generic Cryptographic Authentication (GCA) mode.

key-id: Uniquely identifies an SA in the range of 1 to 65535. The sender inserts the Key ID into the authentication TLV, and the receiver authenticates the packet by using the SA that is selected based on the Key ID.

hmac-sha-1: Specifies the HMAC-SHA-1 algorithm.

hmac-sha-224: Specifies the HMAC-SHA-224 algorithm.

hmac-sha-256: Specifies the HMAC-SHA-256 algorithm.

hmac-sha-384: Specifies the HMAC-SHA-384 algorithm.

hmac-sha-512: Specifies the HMAC-SHA-512 algorithm.

nonstandard: Specifies the nonstandard GCA mode.

md5: Specifies the MD5 authentication mode.

simple: Specifies the simple authentication mode.

cipher: Specifies a key in encrypted form.

plain: Specifies a key in plaintext form. For security purposes, the key specified in plaintext form will be stored in encrypted form.

string: Specifies the key. In simple authentication mode and GCA authentication mode, the plaintext form of the key is a case-sensitive string of 1 to 16 characters, and the encrypted form is a case-sensitive string of 33 to 53 characters. In MD5 authentication mode, the plaintext form of the key is a case-sensitive string of 1 to 255 characters, and the encrypted form is a case-sensitive string of 33 to 373 characters.

keychain: Specifies the keychain authentication mode.

keychain-name: Specifies a keychain by its name, a case-sensitive string of 1 to 63 characters.

ip: Checks IP-related fields in LSPs.

osi: Checks OSI-related fields in LSPs.

Usage guidelines

Area authentication enables IS-IS to discard routes from untrusted devices.

The key in the specified mode is inserted into all outbound Level-1 packets (LSP, CSNP, and PSNP) and is used to authenticate inbound Level-1 packets.

IS-IS keychain authentication supports the HMAC-MD5 and HMAC-SM3 authentication algorithms. If the HMAC-MD5 algorithm is used, the key ID can be any value in the range supported by the key-id argument. If the HMAC-SM3 algorithm is used, the key ID must be in the range of 0 to 65535.

When keychain authentication is used, IS-IS receives and sends packets as follows:

· Before IS-IS sends a Level-1 packet, it uses the valid send key obtained from the keychain to authenticate the packet. If no valid send key exists or the valid send key does not use the HMAC-MD5 or HMAC-SM3 algorithm, the authentication fails and the packet does not contain authentication information.

· After IS-IS receives a Level-1 packet, it processes the packet as follows:

¡ If the authentication algorithm of the packet is HMAC-MD5, IS-IS uses a valid accept key obtained from the keychain to authenticate the packet. If no valid accept key exists or all valid accept keys fail to authenticate the packet, the authentication fails and the packet is discarded.

¡ If the authentication algorithm of the packet is HMAC-SM3, IS-IS uses the key ID of the received packet to obtain the corresponding valid accept key from the keychain. Then, IS-IS uses the accept key to authenticate the packet. If IS-IS cannot find a valid accept key based on the key ID of the received packet or the packet fails the authentication, the packet is discarded.

Devices in an area must have the same authentication mode and key.

If neither ip nor osi is specified, OSI-related fields are checked.

When you specify the GCA mode, follow these guidelines:

· If you do not specify the nonstandard keyword, the device can communicate only with devices that use the GCA mode.

· If you specify the nonstandard keyword, the device can communicate only with devices that use the nonstandard GCA mode.

In MD5 authentication mode, execute the undo area-authentication-mode command before version switch if the key lengths supported by the two versions are different.

Examples

# Set the area authentication mode to simple, and set the plaintext key to 123456.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] area-authentication-mode simple plain 123456

Related commands

area-authentication send-only

domain-authentication-mode

isis authentication-mode

auto-cost enable

Use auto-cost enable to enable automatic link cost calculation.

Use undo auto-cost enable to disable automatic link cost calculation.

Syntax

auto-cost enable

undo auto-cost enable

Default

Automatic link cost calculation is disabled.

Views

IS-IS view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Usage guidelines

After automatic link cost calculation is enabled, the link cost is automatically calculated based on the bandwidth reference value of an interface. When the cost-style is wide or wide-compatible, the cost value of an interface is calculated by using the following formula: Cost = (Reference bandwidth value / Link bandwidth) × 10. For other cost styles, Table 1 applies.

Table 1 Automatic cost calculation scheme for cost styles other than wide and wide-compatible

Interface bandwidth	Cost
≤10 Mbps	60
≤100 Mbps	50
≤155 Mbps	40
≤622 Mbps	30
≤2500 Mbps	20
>2500 Mbps	10

Examples

# Enable automatic link cost calculation for IS-IS process 1.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] auto-cost enable

Related commands

bandwidth-reference

cost-style

isis cost

isis ipv6 cost

bandwidth-reference

Use bandwidth-reference to set the bandwidth reference value for automatic link cost calculation.

Use undo bandwidth-reference to restore the default.

Syntax

bandwidth-reference value

undo bandwidth-reference

Default

The bandwidth reference value is 100 Mbps.

Views

IS-IS view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

value: Specifies the bandwidth reference value in the range of 1 to 2147483648 Mbps.

Examples

# Set the bandwidth reference of IS-IS process 1 to 200 Mbps.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] bandwidth-reference 200

Related commands

auto-cost enable

isis cost

circuit-cost

Use circuit-cost to set a global IS-IS link cost.

Use undo circuit-cost to remove the configuration.

Syntax

circuit-cost cost-value [ level-1 | level-2 ]

undo circuit-cost [ level-1 | level-2 ]

Default

No global link cost is configured.

Views

IS-IS view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

cost-value: Specifies the link cost value. The value range varies by cost style.

· For styles narrow, narrow-compatible, and compatible, the cost value is in the range of 1 to 63.

· For styles wide and wide-compatible, the cost value is in the range of 1 to 16777215.

level-1: Applies the link cost to Level-1.

level-2: Applies the link cost to Level-2.

Usage guidelines

If no level is specified, the specified cost applies to both Level-1 and Level-2.

Examples

# Set the global Level-1 link cost to 11 for IS-IS process 1.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] circuit-cost 11 level-1

Related commands

cost-style

isis cost

cost-style

Use cost-style to set a cost style.

Use undo cost-style to restore the default.

Syntax

cost-style { narrow | wide | wide-compatible | { compatible | narrow-compatible } [ relax-spf-limit ] }

undo cost-style

Default

The IS-IS cost style is narrow.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

narrow: Receives and sends only narrow cost style packets. The narrow cost is in the range of 1 to 63.

wide: Receives and sends only wide cost style packets. The wide cost is in the range of 1 to 16777215.

compatible: Receives and sends both wide and narrow cost style packets.

narrow-compatible: Receives both narrow and wide cost style packets, but sends only narrow cost style packets.

wide-compatible: Receives both narrow and wide cost style packets, but sends only wide cost style packets.

relax-spf-limit: Allows receiving routes with a cost greater than 1023. If you do not specify this keyword, routes with a cost bigger than 1023 will be discarded. This keyword is available only when compatible or narrow-compatible is used.

Examples

# Configure the device to send only narrow cost style packets, but receive both narrow and wide cost style packets.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] cost-style narrow-compatible

Related commands

circuit-cost

isis cost

default-route-advertise

Use default-route-advertise to advertise a default route of 0.0.0.0/0.

Use undo default-route-advertise to restore the default.

Syntax

undo default-route-advertise

Default

Default route advertisement is disabled.

Views

IS-IS IPv4 unicast address family view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

avoid-learning: Avoids learning the default route received in LSPs or generated by using the ATT bit to avoid routing loops.

level-1: Advertises a Level-1 default route.

level-1-2: Advertises both Level-1 and Level-2 default routes.

level-2: Advertises a Level-2 default route.

route-policy route-policy-name: Specifies a routing policy by its name, a case-sensitive string of 1 to 63 characters.

tag tag: Specifies the tag value for the default route, in the range of 1 to 4294967295.

Usage guidelines

If no level is specified, a Level-2 default route is advertised.

The Level-1 default route is advertised to other devices in the same area, and the Level-2 default route is advertised to all the Level-2 and Level-1-2 devices.

You can use a routing policy to specify a level for the default route. The apply isis level-1 command in routing policy view can generate a Level-1 default route. The apply isis level-2 command in routing policy view can generate a Level-2 default route. The apply isis level-1-2 command in routing policy view can generate both a Level-1 default route and Level-2 default route.

The tag value specified in the routing policy takes precedence over the tag value specified in this command.

Examples

# Configure IS-IS process 1 to advertise a Level-2 default route.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] default-route-advertise

display isis

Use display isis to display configuration information for an IS-IS process.

Syntax

display isis [ process-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

process-id: Specifies a process by its ID in the range of 1 to 65535. If you do not specify this argument, the command displays configuration information for all IS-IS processes.

Examples

# Display IS-IS configuration information.

<Sysname> display isis

IS-IS(1) Protocol Information

Instance identifier : 0

Network entity : 10.0000.0000.0001.00

IS level : level-1-2

Cost style : Wide

Fast reroute : LFA level-1-2

Fast-reroute TI-LFA

level-1 : Enabled

level-2 : Enabled

Microloop-avoidance

level-1 : Disabled

level-2 : Disabled

Microloop-avoidance RIB-update-delay

level-1 : 5000

level-2 : 5000

Fast-reroute remote-LFA

level-1 : Disabled

level-2 : Disabled

Node-protecting preference

level-1 : 40

level-2 : 40

Lowest-cost preference

level-1 : 20

level-2 : 20

SRLG preference

level-1 : 10

level-2 : 10

Preference : 15

LSP length receive : 1497

LSP length originate

level-1 : 1497

level-2 : 1497

Maximum imported routes : 1000

Timers

LSP-max-age : 1200

LSP-refresh : 900

SPF mode : Normal

SPF intervals : 5 50 200

IPv6 enabled

Fast reroute : Disabled

Preference : 15

Maximum imported routes : 1000

Segment routing IPv4

MPLS : Disabled

Adjacency : Disabled

Member-port adjacency : Disabled

Configured SRGB : 18000 190000

Effective SRGB : 18000 190000

Level-1 tunnel count : 0

Level-2 tunnel count : 0

Local block : 15000 15999

Segment routing IPv6

SRv6 : Disabled

Table 2 Command output

Field	Description
Instance identifier	Multi-instance process ID.
Network-entity	Network entity name.
IS level	IS-IS routing level.
Cost style	Cost style.
Fast reroute	IS-IS FRR status: · Disabled—IS-IS FRR is disabled. · LFA level-1-2—IS-IS FRR automatically calculates a backup next hop only for non-ECMP routes. · Route-policy—IS-IS FRR specifies a backup next hop by using a routing policy. · LFA ecmp-shared—IS-IS FRR automatically calculates a backup next hop for all routes, including ECMP routes. ECMP routes share one backup next hop.
Fast-reroute TI-LFA	Topology independent LFA (TI-LFA) FRR status: Disabled or Enabled.
Microloop-avoidance	Microloop avoidance status: Disabled or Enabled.
Microloop-avoidance RIB-update-delay	Microloop avoidance delay timer.
Fast-reroute remote-LFA	Remote LFA FRR status: Disabled or Enabled.
Node-protecting preference	Priority of the node-protection backup path selection policy.
Lowest-cost preference	Priority of the lowest-cost backup path selection policy.
SRLG preference	Priority of the shared risk link group (SRLG)-disjoint backup path selection policy.
Preference	IS-IS route preference.
LSP length receive	Maximum LSP that can be received.
LSP length originate	Maximum LSP that can be generated.
Maximum imported routes	Maximum number of redistributed Level-1/Level-2 IPv4/IPv6 routes.
Timers	Timers: · LSP-max-age—Maximum life period of LSPs. · LSP-refresh—Refresh interval of LSPs. · SPF mode—SPF interval calculation mode. · SPF intervals—Interval between SPF calculations.
IPv6 enabled	IPv6 is enabled.
Topology	IPv4 unicast topology name.
Overload status	Overload bit status: · Overloaded manually—The overload bit is set manually. · Overloaded on startup—The overload bit is set on system startup. · Overloaded on startup waiting for nbr system-id up timeout1—The overload bit is set within the timeout1 interval waiting the neighbor system-id to come up. · Overloaded on startup after nbr system-id up timeout1—The overload bit is set within the timeout1 interval after the neighbor system-id comes up. · Overloaded for memory shortage—The overload bit is set for memory shortage. · Overloaded for graceful starting—The overload bit is set during the GR starting period.
Segment routing IPv4		IPv4 segment routing is supported.
MPLS		MPLS SR status: Disabled or Enabled.
Adjacency		Adjacency label allocation status: Disabled or Enabled.
Member-port adjacency		Whether adjacency label allocation is enabled on member interfaces: · Disabled. · Enabled.
Configured SRGB		Configured SRGB range. This field is displayed when SRGB is configured.
Effective SRGB		SRGB range that takes effect.
Segment routing IPv6		This field is not supported in the current software version. IPv6 segment routing is supported.
SRv6		This field is not supported in the current software version. Whether SRv6 is enabled.
Level-1 tunnel count		Number of Level-1 SR tunnels.
Level-2 tunnel count		Number of Level-2 SR tunnels.
Local block		Minimum and maximum label values of the SRLB.

display isis event-log graceful-restart

Use display isis event-log graceful-restart to display IS-IS GR log information.

Syntax

display isis event-log graceful-restart slot slot-number

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies the slot number of the device, which is fixed at 1.

Examples

# Display IS-IS GR log information for the specified slot.

<Sysname> display isis event-log graceful-restart slot 1

IS-IS loginfo :

Sep 18 08:48:24 2015 slot 1 Process 1 enter GR restarting phase(Initialization).

Sep 18 08:48:24 2015 slot 1 Process 1 enter GR phase (LSDB synchronization).

Sep 18 08:48:24 2015 slot 1 Process 1 enter GR phase (TE tunnel prepare).

Sep 18 08:48:24 2015 slot 1 Process 1 enter GR phase (First SPF computation).

Sep 18 08:48:25 2015 slot 1 Process 1 enter GR phase (Redistribution).

Sep 18 08:48:25 2015 slot 1 Process 1 enter GR phase (Second SPF computation).

Sep 18 08:48:25 2015 slot 1 Process 1 enter GR phase (LSP stability).

Sep 18 08:48:25 2015 slot 1 Process 1 enter GR phase (LSP generation).

Sep 18 08:48:25 2015 slot 1 Process 1 enter GR phase (Finish).

Sep 18 08:48:25 2015 slot 1 Process 1 GR complete.

Table 3 Command output

Field	Description
GR phase	GR phase: · Initialization. · LSDB synchronization. · TE tunnel prepare—Preparing for TE tunnel computation. · First SPF computation. · Redistribution. · Second SPF computation. · LSP stability—Ready to generate LSPs. · LSP generation. · Finish.

Field

Description

GR phase

GR phase:

· Initialization.

· LSDB synchronization.

· TE tunnel prepare—Preparing for TE tunnel computation.

· First SPF computation.

· Redistribution.

· Second SPF computation.

· LSP stability—Ready to generate LSPs.

· LSP generation.

· Finish.

display isis event-log lsp

Use display isis event-log lsp to display IS-IS LSP log information.

Syntax

display isis event-log lsp { purged | refreshed } [ level-1 | level-2 ] [ process-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

purged: Displays log information about purged LSPs.

refreshed: Displays log information about refreshed LSPs, including generated and received LSPs.

level-1: Displays Level-1 LSP log information.

level-2: Displays Level-2 LSP log information.

process-id: Specifies a process by its ID in the range of 1 to 65535. If you do not specify this argument, the command displays LSP log information for all IS-IS processes.

Usage guidelines

If you do not specify a level, the command displays both Level-1 and Level-2 LSP log information.

Examples

# Displays log information about purged LSPs.

<Sysname> display isis event-log lsp purged

LSP log for IS-IS(1)

--------------------

Level-1 LSP log

---------------

Date Time LSP ID Seq Num Event

--------------------------------------------------------------------------------

2017-07-31 10:19:48 1111.1111.1111.01-00 0x00000001 Generated LSP purge packet

2017-07-31 10:19:48 1111.1111.1111.01-00 0x00000001 Received LSP purge packet

2017-07-31 10:15:29 2222.2222.2222.01-00 0x00000005 Generated LSP purge packet

Level-2 LSP log

---------------

Date Time LSP ID Seq Num Event

--------------------------------------------------------------------------------

2017-07-31 10:19:48 1111.1111.1111.01-00 0x00000001 Generated LSP purge packet

2017-07-31 10:19:48 1111.1111.1111.01-00 0x00000001 Received LSP purge packet

2017-07-31 10:15:29 2222.2222.2222.01-00 0x00000005 Generated LSP purge packet

# Displays log information about refreshed LSPs.

<Sysname> display isis event-log lsp refreshed

LSP log for IS-IS(1)

--------------------

Level-1 LSP log

---------------

Date Time LSP ID Seq Num Event

--------------------------------------------------------------------------------

2017-06-06 17:18:48 0000.0000.0012.00-00 0x00000038 Received LSP

2017-06-06 17:18:48 0000.0000.0011.00-00 0x00000042 Received LSP

2017-06-06 17:18:48 0000.0000.0012.00-00 0x00000039 Generated LSP

2017-06-06 17:18:48 0000.0000.0012.00-00 0x00000038 Received LSP

2017-06-06 17:18:48 0000.0000.0011.00-00 0x00000042 Received LSP

2017-06-06 17:18:48 0000.0000.0012.00-00 0x00000002 Generated LSP

2017-06-06 17:18:48 0000.0000.0011.01-00 0x00000032 Received LSP

2017-06-06 17:18:48 0000.0000.0011.02-00 0x00000035 Received LSP

2017-06-06 17:18:48 0000.0000.0011.01-00 0x00000032 Received LSP

2017-06-06 17:18:48 0000.0000.0011.02-00 0x00000035 Received LSP

2017-06-06 17:18:47 0000.0000.0012.00-00 0x00000001 Generated LSP

Level-2 LSP log

---------------

Date Time LSPID Seq Num Event

--------------------------------------------------------------------------------

2017-06-06 17:18:48 0000.0000.0012.00-00 0x00000002 Generated LSP

2017-06-06 17:18:47 0000.0000.0012.00-00 0x00000001 Generated LSP

Table 4 Command output

Field	Description
Date	Date of the LSP change.
Time	Time of the LSP change.
LSPID	LSP ID.
Seq Num	LSP sequence number.
Event	LSP change event: · Received LSP. · Received LSP purge packet. · Generated LSP. · Generated LSP purge packet.

Related commands

reset isis event-log lsp

display isis event-log spf

Use display isis event-log spf to display IS-IS route calculation log information.

Syntax

display isis event-log spf [ ipv4 | ipv6 ] [ [ level-1 | level-2 ] | verbose ] * [ process-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ipv4: Displays IS-IS IPv4 route calculation log information.

ipv6: Displays IS-IS IPv6 route calculation log information.

level-1: Displays Level-1 route calculation log information.

level-2: Displays Level-2 route calculation log information.

verbose: Displays detailed route calculation log information. If you do not specify this keyword, the command displays brief route calculation log information.

process-id: Specifies a process by its ID in the range of 1 to 65535. If you do not specify this argument, the command displays route calculation log information for all IS-IS processes.

Usage guidelines

If you specify neither the ipv4 nor ipv6 keyword, the command displays IS-IS IPv4 route calculation log information for the public network.

If you do not specify a level, the command displays both Level-1 and Level-2 route calculation log information.

Examples

# Display brief IS-IS route calculation log information.

<Sysname> display isis event-log spf

SPF Log for IS-IS(1)

--------------------

Level-1 SPF Log

---------------

Date Time Duration Count Trigger event

-------------------------------------------------------------------------------

2018-12-07 11:11:45 0.003 2 LDP label changed

2018-12-07 11:11:10 0 2 Remote LFA configuration changed

2018-12-07 11:10:45 0 4 Interface metric changed

2018-12-07 09:26:40 0 4 LSP updated

2018-12-07 09:26:28 0 2 DIS changed

2018-12-07 09:26:21 0.001 2 LSP updated

2018-12-07 09:26:07 0.001 3 Direct route changed

Level-2 SPF Log

---------------

Date Time Duration Count Trigger event

-------------------------------------------------------------------------------

2018-12-07 11:11:45 0.003 2 LDP label changed

2018-12-07 11:11:10 0 2 Remote LFA configuration changed

2018-12-07 11:10:45 0 4 Interface metric changed

2018-12-07 09:26:40 0 4 LSP updated

2018-12-07 09:26:28 0 2 DIS changed

2018-12-07 09:26:21 0 2 LSP updated

2018-12-07 09:26:07 0 3 Direct route changed

# Display detailed IS-IS route calculation log information.

<Sysname> display isis event-log spf verbose

SPF Log for IS-IS(1)

--------------------

Level-1 SPF Log

---------------

Log date : 2018-12-07 11:10:45

Log key : 5

Trigger count : 4

Trigger event : Interface metric changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 3

BSPF 0 Candidate NBRs: 1

TI/R-LFA prepare 0 TI/R-LFA links: 0, TI/R-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 1

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 1 delete: 0

Last 10 routes:

1.1.1.0/24

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2018-12-07 09:26:40

Log key : 4

Trigger count : 4

Trigger event : LSP updated

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 3

BSPF 0 Candidate NBRs: 1

TI/R-LFA prepare 0 TI/R-LFA links: 0, TI/R-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 1

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2018-12-07 09:26:28

Log key : 3

Trigger count : 2

Trigger event : DIS changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF links changed: 1

BSPF 0 Candidate NBRs: 0

TI/R-LFA prepare 0 TI/R-LFA links: 0, TI/R-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 0

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2018-12-07 09:26:21

Log key : 2

Trigger count : 2

Trigger event : LSP updated

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 0

BSPF 0 Candidate NBRs: 0

TI/R-LFA prepare 0 TI/R-LFA links: 0, TI/R-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 1

PRC 0.001 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0.001

Log date : 2018-12-07 09:26:07

Log key : 1

Trigger count : 3

Trigger event : Direct route changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 0

BSPF 0 Candidate NBRs: 0

TI/R-LFA prepare 0 TI/R-LFA links: 0, TI/R-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 1

PRC 0.001 Add: 1 modify: 0 delete: 0

Last 10 routes:

1.1.1.0/24

Route summary 0 Summary route nodes: 0

Total 0.001

Level-2 SPF Log

---------------

Log date : 2018-12-07 11:10:45

Log key : 5

Trigger count : 4

Trigger event : Interface metric changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 3

BSPF 0 Candidate NBRs: 1

TI/R-LFA prepare 0 TI/R-LFA links: 0, TI/R-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 1

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2018-12-07 09:26:40

Log key : 4

Trigger count : 4

Trigger event : LSP updated

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 3

BSPF 0 Candidate NBRs: 1

TI/R-LFA prepare 0 TI/R-LFA links: 0, TI/R-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 1

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2018-12-07 09:26:28

Log key : 3

Trigger count : 2

Trigger event : DIS changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF links changed: 1

BSPF 0 Candidate NBRs: 0

TI/R-LFA prepare 0 TI/R-LFA links: 0, TI/R-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 0

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2018-12-07 09:26:21

Log key : 2

Trigger count : 2

Trigger event : LSP updated

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 0

BSPF 0 Candidate NBRs: 0

TI/R-LFA prepare 0 TI/R-LFA links: 0, TI/R-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2018-12-07 09:26:07

Log key : 1

Trigger count : 3

Trigger event : Direct route changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 0

BSPF 0 Candidate NBRs: 0

TI/R-LFA prepare 0 TI/R-LFA links: 0, TI/R-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Table 5 Command output

Field	Description
Date	Start date of route calculation.
Time	Start time of route calculation.
Duration	Route calculation duration in seconds. The value is accurate to six decimal places.
Count	Number of events that trigger the current route calculation.
Trigger event	Type of the most recent event that triggers route calculation: · NextHop changed. · DIS changed. · Interface metric changed. · SPF link changed. · Default route changed. · Summary route changed. · TE tunnel updated. · TE tunnel metric changed. · FRR configuration changed. · Prefix priority configuration changed. · Route preference changed. · ISPF configuration changed. · Import filter policy changed. · ECMP configuration changed. · PIC configuration changed. · Interface LFA exclude changed. · ATT configuration changed. · GR over. · T3 timeout. · Direct route changed. · Logic interface changed. · Route leakage configuration changed. · Entered overload state. · Exited overload state. · Area address changed. · Route policy changed. · Redistributed route updated. · LSP updated. · TE tunnel configuration changed. · TE tunnel destination changed. · RIB smooth. · Remote LFA configuration changed. · LDP label changed.
Log date	Generation time of the route calculation logs.
Log key	Route calculation log key.
Trigger count	Number of events that trigger the current route calculation.
SPF details	Detailed information about the route calculation phases.
Phase	Route calculation phase: · TE tunnel ADJ—TE tunnel adjacency calculation. · Topology—Topology calculation. · BSPF—Backup SPF calculation. · TI/R-LFA prepare—TI-LFA/Remote LFA calculation preparation. · Link PSPF—SPF calculation after PSPF convergence for link protection. · Link PQ—P space and Q space calculation for link protection. · Node PSPF—SPF calculation after PSPF convergence for node protection. · Node PQ—P space and Q space calculation for node protection. · LFA—LFA calculation. · Area—Area calculation. · PRC—Prefix calculation. · Route summary—Route summarization calculation.
Description	Route calculation phase description: · TE SPF nodes—Number of SPF nodes for TE tunnel adjacency calculation. · SPF nodes—Number of SPF nodes for topology calculation. · Candidate NBRs—Number of candidate neighbors. · TI/R-LFA links—Number of TI-LFA/remote LFA protected links. · TI/R-LFA nodes—Number of TI-LFA/remote LFA protected nodes. · LFA SPF nodes—Number of SPF nodes for LFA calculation. · Area addresses—Number of area addresses. · Add, modify, and delete—Prefix calculation summary. · Last 10 routes—10 routes that are most recently calculated. · Summary route nodes—Number of summarized routes.
Total	Total duration time of all route calculation phases.

# Display brief IPv6 IS-IS route calculation log information.

<Sysname> display isis event-log spf ipv6

SPF Log for IS-IS(1)

--------------------

Level-1 SPF Log

---------------

Date Time Duration Count Trigger event

-------------------------------------------------------------------------------

2015-09-07 11:10:45 0 4 Interface metric changed

2015-09-07 09:26:40 0 4 LSP updated

2015-09-07 09:26:28 0 2 DIS changed

2015-09-07 09:26:21 0.001 2 LSP updated

2015-09-07 09:26:07 0.001 3 Direct route changed

Level-2 SPF Log

---------------

Date Time Duration Count Trigger event

-------------------------------------------------------------------------------

2015-09-07 11:10:45 0 4 Interface metric changed

2015-09-07 09:26:40 0 4 LSP updated

2015-09-07 09:26:28 0 2 DIS changed

2015-09-07 09:26:21 0 2 LSP updated

2015-09-07 09:26:07 0 3 Direct route changed

# Display detailed IPv6 IS-IS route calculation log information.

<Sysname> display isis event-log spf ipv6 verbose

SPF Log for IS-IS(1)

--------------------

Level-1 SPF Log

---------------

Log date : 2015-09-07 02:18:09

Log key : 10

Trigger count : 2

Trigger event : LSP updated

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 0

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 0

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2015-09-07 02:18:09

Log key : 9

Trigger count : 2

Trigger event : NextHop changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0.003 SPF nodes: 3

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0.003

Log date : 2011-01-01 02:17:40

Log key : 8

Trigger count : 2

Trigger event : Logic interface changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 0

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 0

PRC 0.005 Add: 1 modify: 0 delete: 0

Last 10 routes:

10::/64

Route summary 0 Summary route nodes: 0

Total 0.005

Log date : 2015-09-07 02:17:38

Log key : 7

Trigger count : 1

Trigger event : Logic interface changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 0

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 0

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2015-09-07 02:17:33

Log key : 6

Trigger count : 5

Trigger event : NextHop changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF links changed: 1

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 0

PRC 0.003 Add: 0 modify: 0 delete: 1

Last 10 routes:

3::/24

Route summary 0 Summary route nodes: 0

Total 0.003

Log date : 2015-09-07 02:17:21

Log key : 5

Trigger count : 1

Trigger event : Direct route changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 0

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 0

PRC 0.006 Add: 1 modify: 0 delete: 0

Last 10 routes:

3::/24

Route summary 0 Summary route nodes: 0

Total 0.006

Log date : 2015-09-07 02:17:11

Log key : 4

Trigger count : 1

Trigger event : IPv6 mode changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 3

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2015-09-07 01:09:33

Log key : 3

Trigger count : 2

Trigger event : DIS changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0.001 SPF nodes: 3

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0.001

Log date : 2015-09-07 01:09:25

Log key : 2

Trigger count : 2

Trigger event : LSP updated

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF links changed: 1

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2015-09-07 01:08:49

Log key : 1

Trigger count : 1

Trigger event : Area address changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 0

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Level-2 SPF Log

---------------

Log date : 2015-09-07 02:18:09

Log key : 10

Trigger count : 2

Trigger event : LSP updated

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 0

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 0

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2015-09-07 02:18:09

Log key : 9

Trigger count : 2

Trigger event : NextHop changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0.002 SPF nodes: 3

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0.001 Summary route nodes: 0

Total 0.003

Log date : 2015-09-07 02:17:40

Log key : 8

Trigger count : 2

Trigger event : Logic interface changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 0

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 0

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2015-09-07 02:17:38

Log key : 7

Trigger count : 1

Trigger event : Logic interface changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 0

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 0

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2015-09-07 02:17:33

Log key : 6

Trigger count : 5

Trigger event : NextHop changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF links changed: 1

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 0

PRC 0.001 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0.001

Log date : 2015-09-07 02:17:21

Log key : 5

Trigger count : 1

Trigger event : Direct route changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 0

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 0

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2015-09-07 02:17:11

Log key : 4

Trigger count : 1

Trigger event : IPv6 mode changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0.001 SPF nodes: 3

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0.001

Log date : 2015-09-07 01:09:33

Log key : 3

Trigger count : 2

Trigger event : DIS changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 3

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2015-09-07 01:09:25

Log key : 2

Trigger count : 2

Trigger event : LSP updated

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF links changed: 1

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Log date : 2015-09-07 01:08:49

Log key : 1

Trigger count : 1

Trigger event : Area address changed

SPF details :

Phase Duration Description

TE tunnel ADJ 0 TE SPF nodes: 0

Topology 0 SPF nodes: 0

BSPF 0 Candidate NBRs: 0

TI-LFA prepare 0 TI-LFA links: 0, TI-LFA nodes: 0

Link PSPF 0

Link PQ 0

Node PSPF 0

Node PQ 0

LFA 0 LFA SPF nodes: 0

Area 0 Area addresses: 1

PRC 0 Add: 0 modify: 0 delete: 0

Route summary 0 Summary route nodes: 0

Total 0

Table 6 Command output

Field	Description
Date	Start date of route calculation.
Time	Start time of route calculation.
Duration	Route calculation duration in seconds. The value is accurate to six decimal places.
Count	Number of events that trigger the current route calculation.
Trigger event	Type of the most recent event that triggers route calculation: · NextHop changed. · DIS changed. · Interface metric changed. · SPF link changed. · Default route changed. · Summary route changed. · IPv6 mode changed. · TE tunnel updated. · TE tunnel metric changed. · FRR configuration changed. · Prefix priority configuration changed. · Route preference changed. · ISPF configuration changed. · Import filter policy changed. · ECMP configuration changed. · PIC configuration changed. · Interface LFA exclude changed. · ATT configuration changed. · GR over. · T3 timeout. · Direct route changed. · Logic interface changed. · Route leakage configuration changed. · Entered overload state. · Exited overload state. · Area address changed. · Route policy changed. · Redistributed route updated. · LSP updated. · MT disabled. · MT enabled. · TE tunnel configuration changed. · TE tunnel destination changed. · RIB smooth.
Log date	Generation time of the route calculation logs.
Log key	Route calculation log key.
Trigger count	Number of events that trigger the current route calculation.
SPF details	Detailed information about the route calculation phases.
Phase	Route calculation phase: · TE tunnel ADJ—TE tunnel adjacency calculation. · Topology—Topology calculation. · BSPF—Backup SPF calculation. · TI-LFA prepare—TI-LFA calculation preparation. · Link PSPF—SPF calculation after PSPF convergence for link protection. · Link PQ—P space and Q space calculation for link protection. · Node PSPF—SPF calculation after PSPF convergence for node protection. · Node PQ—P space and Q space calculation for node protection. · LFA—LFA calculation. · Area—Area calculation. · PRC—Prefix calculation. · Route summary—Route summarization calculation.
Description	Route calculation phase description: · TE SPF nodes—Number of SPF nodes for TE tunnel adjacency calculation. · SPF nodes—Number of SPF nodes for topology calculation. · Candidate NBRs—Number of candidate neighbors. · TI-LFA links—Number of TI-LFA protected links. · TI-LFA nodes—Number of TI-LFA protected nodes. · LFA SPF nodes—Number of SPF nodes for LFA calculation. · Area addresses—Number of area addresses. · Add, modify, and delete—Prefix calculation summary. · Last 10 routes—10 routes that are most recently calculated. · Summary route nodes—Number of summarized routes.
Total	Total duration time of all route calculation phases.

Related commands

reset isis event-log spf

display isis global-statistics

Use display isis global-statistics to display global IS-IS statistics.

Syntax

display isis global-statistics [ public | vpn-instance vpn-instance-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

public: Specifies the public network.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters.

Usage guidelines

If you do not specify any keywords, the command displays global IS-IS statistics for the public network and all VPN instances.

Examples

# Display global IS-IS statistics.

<Sysname> display isis global-statistics

IS-IS global statistics

Instance count: 2 Process count: 2

Interface information:

Type IPv4 up/down IPv6 up/down

LAN 0/0 0/0

P2P 1/0 0/0

Peer information:

Type IPv4 Up/Init IPv6 Up/Init

LAN Level-1 0/0 0/0

LAN Level-2 0/0 0/0

P2P 1/0 0/0

Packet information:

Total output packets: 1022

Total input packets: 1023

LSP information:

Total level-1 LSPs: 2

Total level-2 LSPs: 2

Route information:

Type IPv4 IPv6

Level-1 1 0

Level-2 2 0

Table 7 Command output

Field	Description
Interface information	Interface status statistics.
Type	Interface link adjacency type.
IPv4 up/down	Number of IPv4 interfaces in up or down state.
IPv6 up/down	Number of IPv6 interfaces in up or down state.
Type	Neighbor type: · LAN Level-1—Number of Level-1 neighbors with the broadcast network type. · LAN Level-2—Number of Level-2 neighbors with the broadcast network type. · P2P—Number of neighbors with the point-to-point (P2P) network type.
IPv4 Up	Number of IPv4 neighbors in up state.
IPv4 Init	Number of IPv4 neighbors in init state.
IPv6 Up	Number of IPv6 neighbors in up state.
IPv6 Init	Number of IPv6 neighbors in init state.
Packet information	Statistics of received and sent protocol packets.
Total output packets	Number of sent protocol packets.
Total input packets	Number of received protocol packets.
LSP information	Number of LSPs in the LSDB.
Total level-1 LSPs	Number of Level-1 LSPs.
Total level-2 LSPs	Number of Level-2 LSPs.
Route Information	Route statistics: · Level-1—Level-1 IS-IS route statistics. · Level-2—Level-2 IS-IS route statistics. · IPv4—IPv4 IS-IS route statistics. · IPv6—IPv6 IS-IS route statistics.

display isis graceful-restart status

Use display isis graceful-restart status to display IS-IS GR state.

Syntax

display isis graceful-restart status [ level-1 | level-2 ] [ process-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

level-1: Displays the IS-IS Level-1 GR state.

level-2: Displays the IS-IS Level-2 GR state.

process-id: Specifies a process by its ID in the range of 1 to 65535. If you do not specify this argument, the command displays GR state of all IS-IS processes.

Examples

# Display IS-IS GR state.

<Sysname> display isis graceful-restart status

Restart information for IS-IS(1)

--------------------------------

Restart status: COMPLETE

Restart phase: Finish

Restart t1: 3, count 10; Restart t2: 60; Restart t3: 300

SA Bit: supported

Level-1 restart information

---------------------------

Total number of interfaces: 1

Number of waiting LSPs: 0

Level-2 restart information

---------------------------

Total number of interfaces: 1

Number of waiting LSPs: 0

Table 8 Command output

Field	Description
Restart status	Current GR state: · RESTARTING—In this state, forwarding can be ensured. · STARTING—In this state, forwarding cannot be ensured. · COMPLETE—GR is completed.
Restart phase	Current Restart phase: · Initialization. · LSDB synchronization. · TE tunnel prepare. · First SPF computation. · Redistribution. · Second SPF computation. · LSP stability—Ready to generate LSPs. · LSP generation. · Finish.
Restart t1	T1 timer, in seconds.
count	Number of T1 timer expirations.
Restart t2	T2 timer, in seconds.
Restart t3	T3 timer, in seconds.
SA Bit	Whether SA is supported.
Total number of interfaces	Total number of IS-IS interfaces.
Number of waiting LSPs	Number of LSPs not obtained by the GR restarter from GR helpers during LSDB synchronization.

display isis interface

Use display isis interface to display IS-IS interface information.

Syntax

display isis interface [ [ interface-type interface-number ] [ verbose ] | statistics ] [ process-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Displays information for a specified IS-IS interface. If you do not specify this argument, the command displays information about all interfaces.

verbose: Displays detailed information about an interface. If you do not specify this keyword, the command displays brief information about an interface.

statistics: Displays IS-IS interface statistics.

process-id: Displays IS-IS interface information for an IS-IS process specified by its ID in the range of 1 to 65535. If you do not specify this argument, the command displays interface information for all IS-IS processes.

Examples

# Display brief IS-IS interface information.

<Sysname> display isis interface

Interface information for IS-IS(1)

----------------------------------

Interface: Vlan-interface100

Index IPv4 state IPv6 state Circuit ID MTU Type DIS

00001 Up Down 1 1497 L1/L2 No/No

# Display detailed IS-IS interface information.

<Sysname> display isis interface verbose

Interface information for IS-IS(1)

----------------------------------

Interface: Vlan-interface100

Index IPv4 state IPv6 state Circuit ID MTU Type DIS

00001 Up Down 1 1497 L1/L2 No/No

SNPA address : 000c-29e8-1bd5

IP address : 192.168.220.10

Secondary IP address(es) :

IPv6 link-local address :

Extended circuit ID : 1

CSNP timer value : L1 10 L2 10

Hello timer value : 10

Hello multiplier value : 3

LSP timer value : L12 33

LSP transmit-throttle count : L12 5

Cost : L1 100 L2 100

Cost source : L1 Default L2 Default

IPv6 cost : L1 10 L2 10

IPv6 cost source : L1 Default L2 Default

Priority : L1 64 L2 64

Retransmit timer value : L12 5

LDP state : L1 Init L2 No-LDP

LDP sync state : L1 Init L2 Achieved

MPLS TE status : L1 Disabled L2 Disabled

Link quality : GOOD

Cost adjusted at low quality : 50

IPv4 BFD : Disabled

IPv6 BFD : Disabled

IPv4 BFD session-restrict-adj : Enabled

IPv6 BFD session-restrict-adj : Disabled

IPv4 FRR LFA backup : L1 Enabled L2 Enabled

IPv6 FRR LFA backup : L1 Enabled L2 Enabled

IPv4 FRR TI-LFA : L1 Enabled L2 Enabled

IPv4 FRR remote-LFA : L1 Enabled L2 Enabled

IPv4 prefix-suppression : Disabled

IPv6 prefix-suppression : Disabled

IPv4 tag : 1

IPv6 tag : 4294967295

IPv4 primary path detection mode : BFD ctrl

IPv6 primary path detection mode : BFD ctrl

# Display detailed information about interfaces enabled with SR.

<Sysname> display isis interface verbose

Interface information for IS-IS(1)

----------------------------------

Interface: LoopBack1

Index IPv4 state IPv6 state Circuit ID MTU Type DIS

00003 Up Down 1 1536 L1/L2 --

SNPA address : 0000-0000-0000

IP address : 111.111.111.111

Secondary IP addresses :

IPv6 link-local address :

Extended circuit ID : 3

CSNP timer value : L1 10 L2 10

Hello timer value : 10

Hello multiplier value : 3

LSP timer value : L12 33

LSP transmit-throttle count : L12 5

Cost : L1 0 L2 0

Cost source : L1 Default L2 Default

IPv6 cost : L1 0 L2 0

IPv6 cost source : L1 Default L2 Default

Priority : L1 64 L2 64

Retransmit timer value : L12 5

MPLS TE status : L1 Disabled L2 Disabled

Link quality : GOOD

Cost adjusted at low quality : 50

IPv4 BFD : Disabled

IPv6 BFD : Disabled

IPv4 BFD session-restrict-adj : Enabled

IPv6 BFD session-restrict-adj : Disabled

IPv4 FRR LFA backup : L1 Enabled L2 Enabled

IPv6 FRR LFA backup : L1 Enabled L2 Enabled

IPv4 FRR TI-LFA : L1 Enabled L2 Enabled

IPv4 FRR remote-LFA : L1 Enabled L2 Enabled

IPv4 prefix suppression : Disabled

IPv6 prefix suppression : Disabled

IPv4 tag : 0

IPv6 tag : 0

Prefix-SID type : Index

Value : 2

Prefix-SID validity : Valid

Static adjacency SID :

Nexthop Adjacency-SID Type Result

100.100.100.100 15555 Absolute Succeeded

8.8.8.8 1000 Index Conflicting

Table 9 Command output

Field	Description
Interface	Interface type and number.
Index	Interface index.
IPv4 state	IPv4 state. · Up—The interface is up at both the link layer and network layer. · Down—The interface is down at the link layer and network layer. · Lnk:Up/IP:Dn—The interface is up at the link layer but is down at the network layer.
IPv6 state	IPv6 state. · Up—The interface is up at both the link layer and network layer. · Down—The interface is down at the link layer and network layer. · Lnk:Up/IP:Dn—The interface is up at the link layer but is down at the network layer.
CircuitID	Circuit ID. · 0(Invalid)—IS-IS is not successfully enabled on the broadcast interface. · 1—IS-IS is successfully enabled on the broadcast interface.
MTU	Interface MTU.
Type	Interface link adjacency type.
DIS	Indicates whether the interface is elected as the Level-1/Level-2 DIS. In a P2P network, this field displays a hyphen (-) because DIS election is not performed.
SNPA address	Subnet access point address.
IP address	Primary IP address.
Secondary IP address(es)	Secondary IP addresses.
IPv6 link-local address	IPv6 link local address.
Extended circuit ID	Extended circuit ID for a P2P link.
CSNP timer value	Interval for sending CSNP packets.
Hello timer value	Interval for sending Hello packets.
Hello multiplier value	Number of invalid Hello packets.
LSP timer value	Minimum interval for sending LSP packets.
LSP transmit-throttle count	Number of LSP packets sent each time.
Cost	Cost of the interface.
Cost source	Link cost source of the interface: · Default—Default link cost. · Global—Global link cost. · Auto—Automatically calculated link cost. · Manual—Manually specified link cost. · IGP_LDP—Link cost advertised by LDP IGP. · LOW—Link cost applied when the link quality of the interface becomes LOW. · Fallback—Link cost applied when the bandwidth of the Layer 3 aggregate interface falls below the threshold. · BFD—Link cost applied when the BFD session goes down. · LinkUp—Maximum link cost advertised to neighbors during the specified time period.
IPv6 cost	IPv6 link cost of the interface.
IPv6 cost source	IPv6 link cost source of the interface: · Default—Default link cost. · Global—Global link cost. · Auto—Automatically calculated link cost. · Manual—Manually specified link cost. · IGP_LDP—Link cost advertised by LDP IGP. · LOW—Link cost applied when the link quality of the interface becomes LOW. · Fallback—Link cost applied when the bandwidth of the Layer 3 aggregate interface falls below the threshold. · BFD—Link cost applied when the BFD session goes down. · LinkUp—Maximum link cost advertised to neighbors during the specified time period.
Priority	DIS priority.
Retransmit timer value	Retransmission interval for LSPs on a P2P link.
MPLS TE status	MPLS TE status: Enabled or Disabled.
Link quality	Link quality: · GOOD—The bit error ratio is below the upper threshold or drops below the lower threshold. · LOW—The bit error ratio exceeds the upper threshold. This field is displayed only when the interface is configured with the isis link-quality adjust-cost command.
Cost adjusted at low quality	Interface cost adjustment parameters: · xx—Value added to the interface cost. When the link quality is LOW, the interface cost is xx plus the original interface cost. · Maximum—Sets the maximum interface cost when the link quality is LOW. This field is displayed only when the interface is configured with the isis link-quality adjust-cost command.
LDP state	LDP state: · Init—LDP is not reported. · No-LDP—LDP is not configured. · Not ready—LDP session is not established. · Ready—LDP session is established.
LDP sync state	LDP synchronization state: · Init—Initialized. · Achieved—Synchronized. · Max cost—Maintain the maximum cost.
IPv4 BFD	Whether BFD for IS-IS is enabled: · Disabled. · Enabled.
IPv6 BFD	Whether BFD for IPv6 IS-IS is enabled: · Disabled. · Enabled.
IPv4 BFD session-restrict-adj	Whether IPv4 adjacency establishment and maintenance control based on BFD session state is enabled: · Disabled. · Enabled.
IPv6 BFD session-restrict-adj	Whether IPv6 adjacency establishment and maintenance control based on BFD session state is enabled: · Disabled. · Enabled.
IPv4 FRR LFA backup	Whether LFA calculation is enabled for IPv4 FRR: · Disabled. · Enabled.
IPv6 FRR LFA backup	Whether LFA calculation is enabled for IPv6 FRR: · Disabled. · Enabled.
IPv4 FRR TI-LFA	IPv4 TI-LFA calculation status: · Disabled. · Enabled.
IPv4 FRR remote-LFA	IPv4 remote LFA calculation status: · Disabled. · Enabled.
IPv4 prefix-suppression	Whether IPv4 IS-IS prefix suppression is enabled: · Disabled. · Enabled.
IPv6 prefix-suppression	Whether IPv6 IS-IS prefix suppression is enabled: · Disabled. · Enabled.
IPv4 tag	IPv4 tag value of the interface.
IPv6 tag	IPv6 tag value of the interface.
IPv4 primary path detection mode	IPv4 primary path detection mode: · BFD ctrl—BFD control packet mode. · BFD echo—BFD echo packet mode.
IPv6 primary path detection mode	IPv6 primary path detection mode: · BFD ctrl—BFD control packet mode. · BFD echo—BFD echo packet mode.
Prefix-SID type		Prefix SID type: · Absolute—Absolute value of the prefix SID. · Index —Index value of the prefix SID.
Value		Prefix SID value.
Prefix-SID validity		Whether the prefix SID is valid: · Invalid—The prefix SID is invalid because it is out of the SRGB range. · Valid—The prefix SID is valid.
Nexthop		Next hop address. This field displays 0.0.0.0 for a P2P network.
Type		Adjacency SID type: · Absolute—Absolute value of the adjacency SID. · Index—Index value of the adjacency SID.
Result		Adjacency SID application result: · Succeeded—Applied for adjacency SID successfully. · Conflicting—Adjacency SID conflict occurred. · Init—Adjacency SID application is in progress or adjacency SID assignment is not enabled.

# Display IS-IS interface statistics.

<Sysname> display isis interface statistics

Interface statistics information for IS-IS(1)

--------------------------------------------

Type IPv4 up/down IPv6 up/down

LAN 1/0 0/0

P2P 0/0 0/0

Table 10 Command output

Field	Description
Type	Network type of the interface: · LAN—Broadcast network. · P2P—Point-to-point network.
IPv4 up	Number of IS-IS interfaces in up state.
IPv4 down	Number of IS-IS interfaces in down state.
IPv6 up	Number of IS-ISv6 interfaces in up state.
IPv6 down	Number of IS-ISv6 interfaces in down state.

display isis lsdb

Use display isis lsdb to display IS-IS LSDB information.

Syntax

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

level-1: Displays the Level-1 LSDB.

level-2: Displays the Level-2 LSDB.

local: Displays LSP information generated locally.

lsp-id lspid: Specifies an LSP ID, in the form of sysID. Pseudo ID-fragment num, where sysID represents the originating node or pseudo node. Pseudo ID is separated by a dot from sysID and by a hyphen from fragment num.

lsp-name lspname: Specifies the LSP name, in the form of Symbolic name.Pseudo ID-fragment num, where Pseudo ID is separated by a dot from Symbolic name and by a hyphen from fragment num. If the Pseudo ID is 0, specify the LSP name in the form Symbolic name-fragment num.

verbose: Displays LSDB detailed information. If you do not specify this keyword, the command displays brief information about LSDB.

process-id: Specifies an IS-IS process by its ID in the range of 1 to 65535. If you do not specify this argument, the command displays LSDBs for all IS-IS processes.

Usage guidelines

If no level is specified, the command displays both Level-1 and Level-2 LSDB information.

Examples

# Display brief Level-1 LSDB information.

<Sysname> display isis lsdb level-1

Database information for IS-IS(1)

--------------------------------

Level-1 Link State Database

---------------------------

LSPID Seq Num Checksum Holdtime Length ATT/P/OL

-------------------------------------------------------------------------------

0000.0000.0001.00-00* 0x00000087 0xf846 1152 183 0/0/0

0000.0000.0003.00-00 0x00000005 0x4bee 520 177 0/0/0

0000.0000.0003.00-01 0x00000004 0x7245 520 45 0/0/0

0000.0000.0011.00-00 0x0000000b 0xcdf6 815 183 0/0/0

*-Self LSP, +-Self LSP(Extended), ATT-Attached, P-Partition, OL-Overload

# Display detailed Level-1 LSDB information.

<Sysname> display isis lsdb level-1 verbose

Database information for IS-IS(1)

--------------------------------

Level-1 Link State Database

---------------------------

LSPID Seq Num Checksum Holdtime Length ATT/P/OL

-------------------------------------------------------------------------------

0000.0000.0001.00-00* 0x00000080 0x73f 1185 183 0/0/0

Source 0000.0000.0001.00

IID 10

ITID 0

NLPID IPv4 IPv6

Area address 10

IPv4 address 192.168.220.10

IPv6 address 100::1

+NBR ID

0000.0000.0011.00 Cost: 100

Admin group: 0x00000000

Physical bandwidth: 12500000 bytes/sec

Reservable bandwidth: 0 bytes/sec

Unreserved bandwidth for each TE class:

TE class 0: 0 bytes/sec TE class 1: 0 bytes/sec

TE class 2: 0 bytes/sec TE class 3: 0 bytes/sec

TE class 4: 0 bytes/sec TE class 5: 0 bytes/sec

TE class 6: 0 bytes/sec TE class 7: 0 bytes/sec

TE class 8: 0 bytes/sec TE class 9: 0 bytes/sec

TE class 10: 0 bytes/sec TE class 11: 0 bytes/sec

TE class 12: 0 bytes/sec TE class 13: 0 bytes/sec

TE class 14: 0 bytes/sec TE class 15: 0 bytes/sec

TE cost: 10

Bandwidth constraint model: Prestandard DS-TE RDM

Bandwidth constraints:

BC[0] : 0 bytes/sec BC[1] : 0 bytes/sec

Neighbor IP address: 192.168.220.30

Interface IP address: 192.168.220.10

LAN-ADJ-SID

Flags (F/B/V/L/S): 0/0/1/1/0 Weight: 0

System ID Adjacency SID

0000.0000.0012 24108

+NBR ID

2222.2222.2222.00 Cost: 10

P2P-ADJ-SID

Flags (F/B/V/L/S): 0/0/0/1/1 Weight: 0

Adjacency SID: 24182

+IP-Extended

192.168.220.0 255.255.255.0 Cost: 100

+IP-Extended

14.159.100.2 255.255.255.255 Cost: 0

Prefix-SID: 3333 Algorithm: 0

Prefix-SID flags (R/N/P/E/V/L): 0/1/0/0/0/0

Router ID 1.1.1.1

0000.0000.0003.00-00 0x00000005 0x4bee 887 177 0/0/0

Source 0000.0000.0003.00

NLPID IPv4

Area address 10

IPv4 address 10.10.10.10

IPv4 address 192.168.220.20

+NBR ID

0000.0000.0001.00 Cost: 10

Admin group: 0x00000000

Physical bandwidth: 12500000 bytes/sec

Reservable bandwidth: 0 bytes/sec

Unreserved bandwidth for each TE class:

TE class 0: 0 bytes/sec TE class 1: 0 bytes/sec

TE class 2: 0 bytes/sec TE class 3: 0 bytes/sec

TE class 4: 0 bytes/sec TE class 5: 0 bytes/sec

TE class 6: 0 bytes/sec TE class 7: 0 bytes/sec

TE class 8: 0 bytes/sec TE class 9: 0 bytes/sec

TE class 10: 0 bytes/sec TE class 11: 0 bytes/sec

TE class 12: 0 bytes/sec TE class 13: 0 bytes/sec

TE class 14: 0 bytes/sec TE class 15: 0 bytes/sec

TE cost: 10

Bandwidth constraint model: Prestandard DS-TE RDM

Bandwidth constraints:

BC[0]: 0 bytes/sec BC[1]: 0 bytes/sec

Interface IP address: 192.168.220.20

Neighbor IP address: 192.168.220.10

LAN-ADJ-SID

Flags (F/B/V/L/S): 0/0/1/1/0 Weight: 0

System ID Adjacency SID

0000.0000.0012 24108

+IP-Extended

14.159.100.2 255.255.255.255 Cost: 0

Prefix-SID: 3333 Algorithm: 0

Prefix-SID flags (R/N/P/E/V/L): 0/1/0/0/0/0

Router ID 3.3.3.3

Router capability

Router ID: 14.159.201.2 Flags (D/S): 0/0

Segment routing (I/V/H): 1/0/0

SRGB base: 16666 SRGB range : 5557

SID binding

11.11.11.11/32 Flags (F/M/S/D/A): 0/0/0/0/0

Weight: 0 Range: 10

Start SID: 10 Algorithm: 0

Prefix-SID flags (R/N/P/E/V/L): 0/0/0/0/0/0

+SRLG NBR ID

0000.0000.0002.00

Interface IP address: 2.1.1.1

Neighbor IP address: 2.1.1.2

Shared risk link group: 45, 100

0000.0000.0003.00-01 0x00000004 0x7245 887 45 0/0/0

Source 0000.0000.0003.00

+IP-Extended

10.10.10.0 255.255.255.0 Cost: 10

+IP-Extended

192.168.220.0 255.255.255.0 Cost: 10

+IP-Extended

14.159.100.2 255.255.255.255 Cost: 0

Prefix-SID: 3333 Algorithm: 0

Prefix-SID flags (R/N/P/E/V/L): 0/1/0/0/0/0

Router capability

Router ID: 14.159.201.2 Flags (D/S): 0/0

Segment routing (I/V/H): 1/0/0

SRGB base: 16666 SRGB range : 5557

*-Self LSP, +-Self LSP(Extended), ATT-Attached, P-Partition, OL-Overload

Table 11 Command output

Field	Description
LSPID	LSP ID.
Seq Num	LSP sequence number.
Checksum	LSP checksum.
Holdtime	LSP lifetime, which decreases as time elapses.
Length	LSP length.
ATT/P/OL	· ATT—Attach bit. · P—Partition bit. · OL—Overload bit. 1 means the LSP bit is set and 0 means the LSP bit is not set.
Source	System ID of the originating router.
HOST NAME	Dynamic host name of the originating router.
ORG ID	Original system ID of the virtual system of the originating router.
IID	Multi-instance process ID.
ITID	Multi-instance topology ID. The value of this field is fixed at 0 in the current software version.
NLPID	Network layer protocol the originating router runs.
Area address	Area address of the originating router.
IPv4 address	IP address of the originating router's IS-IS interface.
IPv6 address	IPv6 address of the originating router's IS-ISv6 interface.
MT ID 0000 (-/-) MT ID 0002 (-/-)	Topology supported by the originating router: · 0000—Standard topology. · 0002—IPv6 unicast topology. · (-/-)—Attach bit/overload bit.
NBR ID	Neighbor ID of the originating router.
IPv6 unicast NBR ID	IPv6 unicast neighbor information about the originating router.
Admin group	Link management group attribute.
Physical bandwidth	Physical bandwidth.
Reservable bandwidth	Reserved bandwidth.
Unreserved bandwidth for each TE class	Available bandwidth reserved for each TE class.
TE class	Available bandwidth for each of the 8 or 16 TE classes.
TE cost	TE cost.
Bandwidth constraint model	Bandwidth constraint model: · Prestandard DS-TE RDM. · IETF DS-TE RDM. · IETF DS-TE MAM.
BC	Bandwidth constraint value. The Prestandard model supports 2 BCs, and the IETF modes support a maximum of 8 BCs.
Interface IP address	IP address of the local interface.
Neighbor IP address	IP address of the remote interface.
Interface IPv6 address	IPv6 address of the local interface.
NBR Interface IPv6 address	IPv6 address of the remote interface.
Router ID	IPv4 router ID.
IP-Internal	Internal IP address and mask of the originating router.
IP-External	External IP address and mask of the originating router.
IP-Extended	Extended information about the originating router, including the IP address, subnet mask, and prefix SID information.
Cost	Cost.
Auth	Authentication information of the originating router.
IPV6	Internal IPv6 address and prefix of the originating router.
IPV6-Ext	External IPv6 address and prefix of the originating router.
IPv4 unicast	IPv4 unicast reachability information about the originating router.
IPv6 unicast	Internal IPv6 unicast reachability information about the originating router.
IPv6 unicast-ext	External IPv6 unicast reachability information about the originating router.
LAN-ADJ-SID	SID advertisement information from the LAN adjacency path.
P2P-ADJ-SID	SID advertisement information from the P2P adjacency path.
Flags (F/B/V/L/S)	Adjacency SID flag: · F—Address family flag. If set, the adjacency SID refers to an IPv6 adjacency. If not set, the adjacency SID refers to an IPv4 adjacency. · B—Backup flag. If set, the adjacency SID is eligible for link protection. · V—Value/Index flag. If set, the adjacency SID carries an absolute value. If not set, the adjacency SID carries an index value. · L—Local flag. If set, the adjacency SID has local significance. If not set, the adjacency SID has global significance. · S—Set flag. If set, the adjacency SID refers to a set of adjacencies.
Weight	Path weight.
Adjacency SID	SID advertised by the adjacency path.
Prefix-SID flags (R/N/P/E/V/L)	Prefix SID flag: · R—Re-advertisement flag. If set, inter-level propagation or route redistribution exists. · N—Node-SID flag. If set, the prefix SID is the SID to an SR node. · P—No-PHP flag. If set, the penultimate node cannot pop the prefix SID. · E—Explicit null flag. If set, the upstream neighbor must replace the prefix SID with an explicit null flag before forwarding the packets. · V—Value/Index flag. If set, the prefix SID carries an absolute value. · L—Local flag. If set, the prefix SID has local significance.
Algorithm	Prefix related algorithm. Only SPF is supported in the current software version.
Router capability	Route capability sub-TLV information.
Flags (D/S)	Inter-level leaking flag: · D—D flag. If set, the route capability TLV cannot be leaked from Level-1 to Level-2. · S—S flag. If set, the route capability TLV must be flooded across the entire routing domain. If not set, the route capability TLV cannot be leaked between levels.
Segment routing (I/V/H)	SR capability sub-TLV flag: · I —MPLS IPv4 flag. If set, the router is capable of processing MPLS SR encapsulated IPv4 packets on all interfaces. · V—MPLS IPv6 flag. If set, the router is capable of processing MPLS SR encapsulated IPv6 packets on all interfaces. This flag is not supported in the current software version. · H—IPv6 SR flag. If set, the router is capable of processing IPv6 SR encapsulated packets with Segment Routing Headers (SRHs) on all interfaces. This flag is not supported in the current software version.
SRGB base	Minimum label value of the SRGB range.
SRGB range	Number of labels of the SRGB.
SID binding	Prefix-SID mapping information.
Flags (F/M/S/D/A)	Mapping flags: · F—Address family flag. If set, the peer is an IPv6 peer. If not set, the peer is an IPv4 peer. · M—Mirror context flag. If set, the SID is used for SR node protection. · S—Scope flag. If set, the route capability TLV can be leaked from Level-1 to Level-2. · D—Down flag. If set, the SID/Label Binding TLV is advertised from Level-2 to Level-1. · A—Attached flag. If set, the prefix and SID are advertised by a directly connected peer.
Range	Number of consecutive SIDs assigned.
L2 bundle member attributes	L2 bundle member attributes TLV.
Flags (P/-/-/-/-/-/-/-)	Flag information. When the P flag is set, the TLV carries sub-TLVs used to distinguish parallel links.
L2 bundle attribute descriptors	L2 bundle attribute descriptors.
Link local identifiers: n	Link ID information about member interfaces. n represents the number of link IDs.
L2-Bundle-Member-LAN-ADJ-SID	Adjacency SID information about member interfaces on LAN adjacency links.
L2-Bundle-Member-ADJ-SID	Adjacency SID information about member interfaces on P2P adjacency links.
Flags (F/*/V/L/S/P/-/-)	Prefix SID flag information: · F—Address family flag. If set, the adjacency SID refers to an IPv6 adjacency. If not set, the adjacency SID refers to an IPv4 adjacency. · V—Value/Index flag. If set, the adjacency SID carries an absolute value. If not set, the adjacency SID carries an index value. · L—Local flag. If set, the adjacency SID has local significance. If not set, the adjacency SID has global significance. · S—Set flag. If set, the adjacency SID refers to a set of adjacencies. · P—Persistence flag. If set, the adjacency SID remains unchanged.
SRLG NBR ID	SRLG neighbor information about the originating router.
Interface IP address	IP address of the local interface.
Neighbor IP address	IP address of the remote interface.
Shared risk link group	Number of the SRLG to which the local interface belongs.

display isis mesh-group

Use display isis mesh-group to display IS-IS mesh group configuration information.

NOTE:

This command is supported only in R3608 and later.

Syntax

display isis mesh-group [ process-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

process-id: Displays IS-IS mesh-group configuration for an IS-IS process specified by its ID in the range of 1 to 65535. If you do not specify this argument, the command displays IS-IS mesh group configuration information for all IS-IS processes.

Examples

# Add HundredGigE 1/0/1 and HundredGigE 1/0/2 to mesh group 100.

<Sysname> system-view

[Sysname] interface hundredgige 1/0/1

[Sysname-HundredGigE1/0/1] isis mesh-group 100

[Sysname-HundredGigE1/0/1] quit

[Sysname] interface hundredgige 1/0/2

[Sysname-HundredGigE1/0/2] isis mesh-group 100

# Display IS-IS mesh-group configuration information.

[Sysname-HundredGigE1/0/2] display isis mesh-group

Mesh Group information for IS-IS(1)

----------------------------------------------------------------------

Interface Status

HGE1/0/1 100

HGE1/0/2 100

Table 12 Command output

Field	Description
Interface	Interface name.
Status	Mesh group the interface belongs to/whether a blocked interface is configured.

display isis lsdb statistics

Use display isis lsdb statistics to display IS-IS LSDB statistics.

Syntax

display isis lsdb statistics [ level-1 | level-2 ] [ process-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

level-1: Displays IS-IS Level-1 LSDB statistics.

level-2: Displays IS-IS Level-2 LSDB statistics.

process-id: Specifies an IS-IS process by its ID in the range of 1 to 65535. If you do not specify this argument, the command displays LSDB statistics for all IS-IS processes.

Usage guidelines

If no level is specified, the command displays both Level-1 and Level-2 LSDB statistics.

Examples

# Display IS-IS LSDB statistics.

<Sysname> display isis lsdb statistics

Database Statistics information for IS-IS(1)

-----------------------------------------

Level-1 LSDB Statistics

-----------------------

LSP source ID LSP count

--------------------------------------------------------------------------------

Total 333

1111.1111.1111.00 1

2222.2222.2222.00 256

2222.2222.2222.01 1

bbbb.bbbb.0001.00 75

Level-2 LSDB Statistics

-----------------------

LSP source ID LSP count

--------------------------------------------------------------------------------

Total 663

1111.1111.1111.00 256

2222.2222.2222.00 256

2222.2222.2222.01 1

aaaa.aaaa.0001.00 75

bbbb.bbbb.0001.00 75

Table 13 Command output

Field	Description
LSP source ID	ID of the source system.
LSP count	Number of LSPs with the same source ID.
Total	Total number of LSPs.

Related commands

display isis lsdb

display isis name-table

Use display isis name-table to display the host name-to-system ID mapping table.

Syntax

display isis name-table [ process-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

process-id: Displays the host name to system ID mapping table for an IS-IS process specified by its ID in the range of 1 to 65535. If you do not specify this argument, the command displays the host name to system ID mapping table for all IS-IS processes.

Examples

# Display the IS-IS host name to system ID mapping table.

<Sysname> display isis name-table

Name table information for IS-IS(1)

-----------------------------------

System ID Hostname Type Level

6789.0000.0001 RUTA DYNAMIC Level-1

6789.0000.0001 RUTA DYNAMIC Level-2

0000.0000.0041 RUTB STATIC Level-1

0000.0000.0041 RUTB STATIC Level-2

6789.0000.0001.01 DIS-A DYNAMIC Level-1

0000.0000.0041.01 DIS-B DYNAMIC Level-2

Table 14 Command output

Field	Description
System ID	System ID.
Hostname	Host name.
Type	Mapping type: · STATIC. · DYNAMIC.
Level	Level on which the system ID-to-host name mapping takes effect: Level-1 or Level-2.

display isis packet

Use display isis packet to display IS-IS packet statistics.

Syntax

display isis packet { csnp | hello | lsp | psnp } by-interface [ verbose ] [ interface-type interface-number ] [ process-id ]

display isis packet { csnp | hello | lsp | psnp } [ verbose ] [ process-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

csnp: Displays CSNP packet statistics.

hello: Displays hello packet statistics.

lsp: Displays LSP packet statistics.

psnp: Displays PSNP packet statistics.

by-interface: Displays packet statistics on a per-interface basis.

verbose: Displays detailed packet statistics.

interface-type interface-number: Specifies an interface by its type and number. If you do not specify this option, the command displays IS-IS packet statistics for all interfaces.

process-id: Specifies an IS-IS process by its ID in the range of 1 to 65535. If you do not specify this argument, the command displays packet statistics for all IS-IS processes.

Examples

# Display detailed hello packet statistics on a per-interface basis.

<Sysname> display isis packet hello by-interface verbose

Hello packet information for IS-IS(1)

-------------------------------------

Interface: Vlan-interface10

Total output packets : 0 Total output error packets : 0

Total input packets : 0 Total input error packets : 0

Input packets with errors

Bad packet length : 0 Bad header length : 0

Jumbo packet : 0 Bad protocol description : 0

Bad protocol ID : 0 Bad protocol version : 0

Unknown packet type : 0 Bad max area count : 0

Bad system ID length : 0 Bad circuit type : 0

Bad auth TLV: 0 Bad area address TLV : 0

Auth failure : 0 Excessive area addresses : 0

Bad NBR TLV : 0 Excessive auth TLVs : 0

Excessive IF Addr TLVs : 0 Excessive IF addresses : 0

Bad IF address TLV : 0 Duplicate system ID : 0

Bad TLV length : 0 Bad IP address : 0

Duplicate IP address : 0 Mismatched area address : 0

Mismatched protocol : 0 Mismatched network type : 0

Bad IPv6 address TLV : 0 Bad IPv6 address : 0

Duplicate IPv6 address : 0 Bad MT ID TLV : 0

SNPA conflict (LAN) : 0 Excessive NBR SNPAs (LAN) : 0

Mismatched level (LAN) : 0 Bad 3-Way option TLV (P2P) : 0

No common MT ID (P2P) : 0 Bad circuit ID (P2P) : 0

Bad IID TLV : 0

# Display detailed hello packet statistics.

<Sysname> display isis packet hello verbose

Hello packet information for IS-IS(1)

-------------------------------------

Total output packets : 0 Total output error packets : 0

Total input packets : 0 Total input error packets : 0

Input packets with errors

Bad packet length : 0 Bad header length : 0

Jumbo packet : 0 Bad protocol description : 0

Bad protocol ID : 0 Bad protocol version : 0

Unknown packet type : 0 Bad max area count : 0

Bad system ID length : 0 Bad circuit type : 0

Bad auth TLV : 0 Bad area address TLV : 0

Auth failure : 0 Excessive area addresses : 0

Bad NBR TLV : 0 Excessive auth TLVs : 0

Excessive IF Addr TLVs : 0 Excessive IF addresses : 0

Bad IF address TLV : 0 Duplicate system ID : 0

Bad TLV length : 0 Bad IP address : 0

Duplicate IP address : 0 Mismatched area address : 0

Mismatched protocol : 0 Mismatched network type : 0

Bad IPv6 address TLV : 0 Bad IPv6 address : 0

Duplicate IPv6 address : 0 Bad MT ID TLV : 0

SNPA conflict (LAN) : 0 Excessive NBR SNPAs (LAN) : 0

Mismatched level (LAN) : 0 Bad 3-Way option TLV (P2P) : 0

No common MT ID (P2P) : 0 Bad circuit ID (P2P) : 0

Bad IID TLV : 0

Table 15 Command output

Field	Description
Input packets with errors	Statistics for packets with the following errors: · Bad packet length—Invalid packet length. · Bad header length—Invalid header length. · Jumbo packet—The packet length exceeds the buffer size or the interface MTU. · Bad protocol description—Invalid protocol description. · Bad protocol ID—Invalid protocol identifier. · Bad protocol version—Invalid protocol version. · Unknown packet type—Unknown packet type. · Bad max area count—Invalid maximum number of area addresses. · Bad system ID length—Invalid system ID length. · Bad circuit type—Invalid interface type. · Bad auth TLV—Invalid authentication TLV. · Bad area address TLV—Invalid area address TLV. · Auth failure—Authentication failure. · Excessive area addresses—Excessive area addresses. · Bad NBR TLV—Invalid neighbor TLV. · Excessive auth TLVs—Excessive authentication TLVs. · Excessive IF Addr TLVs—Excessive interface address TLVs. · Excessive IF addresses—Excessive interface addresses. · Bad IF address TLV—Invalid interface address TLV. · Duplicate system ID—Duplicate system IDs. · Bad TLV length—Invalid TLV length. · Bad IP address—The IP address does not belong to the same network as the local interface address. · Duplicate IP address—Duplicate IP addresses. · Mismatched area address—Mismatched area addresses. · Mismatched protocol—Mismatched protocols. · Mismatched network type—Mismatched network types. · Bad IPv6 address TLV—Invalid IPv6 address TLV. · Bad IPv6 address—Invalid IPv6 address. · Duplicate IPv6 address—Duplicate IPv6 addresses. · Bad MT ID TLV—Invalid topology ID TLV. · SNPA conflict (LAN)—SNPA conflict. · Excessive NBR SNPAs (LAN)—Excessive neighbor SNPAs. · Mismatched level (LAN)—Mismatched levels. · Bad 3-Way option TLV (P2P)—Invalid three-way handshake information. · No common MT ID (P2P)—No common topology ID. · Bad circuit ID (P2P)—Invalid circuit ID. · Bad IID TLV—The multi-instance TLV length is smaller than the minimum length specified in the protocol.

Field

Description

Input packets with errors

Statistics for packets with the following errors:

· Bad packet length—Invalid packet length.

· Bad header length—Invalid header length.

· Jumbo packet—The packet length exceeds the buffer size or the interface MTU.

· Bad protocol description—Invalid protocol description.

· Bad protocol ID—Invalid protocol identifier.

· Bad protocol version—Invalid protocol version.

· Unknown packet type—Unknown packet type.

· Bad max area count—Invalid maximum number of area addresses.

· Bad system ID length—Invalid system ID length.

· Bad circuit type—Invalid interface type.

· Bad auth TLV—Invalid authentication TLV.

· Bad area address TLV—Invalid area address TLV.

· Auth failure—Authentication failure.

· Excessive area addresses—Excessive area addresses.

· Bad NBR TLV—Invalid neighbor TLV.

· Excessive auth TLVs—Excessive authentication TLVs.

· Excessive IF Addr TLVs—Excessive interface address TLVs.

· Excessive IF addresses—Excessive interface addresses.

· Bad IF address TLV—Invalid interface address TLV.

· Duplicate system ID—Duplicate system IDs.

· Bad TLV length—Invalid TLV length.

· Bad IP address—The IP address does not belong to the same network as the local interface address.

· Duplicate IP address—Duplicate IP addresses.

· Mismatched area address—Mismatched area addresses.

· Mismatched protocol—Mismatched protocols.

· Mismatched network type—Mismatched network types.

· Bad IPv6 address TLV—Invalid IPv6 address TLV.

· Bad IPv6 address—Invalid IPv6 address.

· Duplicate IPv6 address—Duplicate IPv6 addresses.

· Bad MT ID TLV—Invalid topology ID TLV.

· SNPA conflict (LAN)—SNPA conflict.

· Excessive NBR SNPAs (LAN)—Excessive neighbor SNPAs.

· Mismatched level (LAN)—Mismatched levels.

· Bad 3-Way option TLV (P2P)—Invalid three-way handshake information.

· No common MT ID (P2P)—No common topology ID.

· Bad circuit ID (P2P)—Invalid circuit ID.

· Bad IID TLV—The multi-instance TLV length is smaller than the minimum length specified in the protocol.

# Display detailed LSP packet statistics on a per-interface basis.

<Sysname> display isis packet lsp by-interface verbose

LSP packet information for IS-IS(1)

-----------------------------------

Interface: Vlan-interface10

Total output packets : 0 Total output error packets : 0

Total input packets : 0 Total input error packets : 0

Input packets with errors

Bad packet length : 0 Bad header length : 0

Jumbo packet : 0 SNPA conflict (LAN) : 0

Smaller than header : 0 Bad protocol description : 0

Bad protocol ID : 0 Bad protocol version : 0

Unknown packet type : 0 Bad max area count : 0

No active NBR : 0 Bad system ID length : 0

Mismatched level : 0 Illegal IS type : 0

Sequence number is 0 : 0 Checksum is 0 : 0

Incorrect checksum : 0 Bad TLV length : 0

Mismatched protocol : 0 Bad auth TLV : 0

Auth failure : 0 Excessive auth TL Vs : 0

Bad NBR TLV : 0 Bad extended IS T LV : 0

Bad IF address TLV : 0 Bad IPv6 IF addre ss TLV : 0

Bad alias TLV : 0 Bad IP reachabili ty TLV : 0

Bad MT IS TLV : 0 Bad area address TLV : 0

Bad MT ID TLV : 0 Bad MT IP TLV : 0

Bad MT IPv6 TLV : 0 Bad IPv6 reachabi lity TLV: 0

Bad router ID TLV : 0 Bad SRLG TLV : 0

Bad IID TLV : 0

# Display detailed LSP packet statistics.

<Sysname> display isis packet lsp verbose

LSP packet information for IS-IS(1)

-----------------------------------

Total output packets : 0 Total output error packets : 0

Total input packets : 0 Total input error packets : 0

Input packets with errors

Bad packet length : 0 Bad header length : 0

Jumbo packet : 0 SNPA conflict (LAN) : 0

Smaller than header : 0 Bad protocol description : 0

Bad protocol ID : 0 Bad protocol version : 0

Unknown packet type : 0 Bad max area count : 0

No active NBR : 0 Bad system ID length : 0

Mismatched level : 0 Illegal IS type : 0

Sequence number is 0 : 0 Checksum is 0 : 0

Incorrect checksum : 0 Bad TLV length : 0

Mismatched protocol : 0 Bad auth TLV : 0

Auth failure : 0 Excessive auth TLVs : 0

Bad NBR TLV : 0 Bad extended IS TLV : 0

Bad IF address TLV : 0 Bad IPv6 IF address TLV : 0

Bad alias TLV : 0 Bad IP reachability TLV : 0

Bad MT IS TLV : 0 Bad area address TLV : 0

Bad MT ID TLV : 0 Bad MT IP TLV : 0

Bad MT IPv6 TLV : 0 Bad IPv6 reachability TLV : 0

Bad router ID TLV : 0 Bad SRLG TLV : 0

Bad IID TLV : 0

Table 16 Command output

Field	Description
Input packets with errors	Statistics for packets with the following errors: · Bad packet length—Invalid packet length. · Bad header length—Invalid header length. · Jumbo packet—The packet length exceeds the maximum length of packets that can be received. · SNPA conflict (LAN)—SNPA conflict. · Smaller than header—The packet length is smaller than the fixed header length. · Bad protocol description—Invalid protocol description. · Bad protocol ID—Invalid protocol identifier. · Bad protocol version—Invalid protocol version. · Unknown packet type—Unknown packet type. · Bad max area count—Invalid maximum number of area addresses. · No active NBR—The packet is from an unknown neighbor. · Bad system ID length—Invalid system ID length. · Mismatched level—Mismatched levels. · Illegal IS type—Invalid IS type. · Sequence number is 0—The sequence number is 0. · Checksum is 0—The checksum is 0. · Incorrect checksum—Incorrect checksum. · Bad TLV length—Invalid TLV length. · Mismatched protocol—Mismatched protocols. · Bad auth TLV—Invalid authentication TLV. · Auth failure—Authentication failure. · Excessive auth TLVs—Excessive authentication TLVs. · Bad NBR TLV—Invalid neighbor TLV. · Bad extended IS TLV—Invalid extended IS TLV. · Bad IF address TLV—Invalid interface address TLV. · Bad IPv6 IF address TLV—Invalid IPv6 interface address TLV. · Bad alias TLV—Invalid alias TLV. · Bad IP reachability TLV—Invalid IP reachability TLV. · Bad MT IS TLV—Invalid topology IS TLV. · Bad area address TLV—Invalid area address TLV. · Bad MT ID TLV—Invalid topology ID TLV. · Bad MT IP TLV—Invalid IPv4 topology TLV. · Bad MT IPv6 TLV—Invalid IPv6 topology TLV. · Bad IPv6 reachability TLV—Invalid IPv6 reachability TLV. · Bad router ID TLV—Invalid router ID TLV. · Bad SRLG TLV—Invalid SRLG TLV. · Bad IID TLV—The multi-instance TLV length is smaller than the minimum length specified in the protocol.

Field

Description

Input packets with errors

Statistics for packets with the following errors:

· Bad packet length—Invalid packet length.

· Bad header length—Invalid header length.

· Jumbo packet—The packet length exceeds the maximum length of packets that can be received.

· SNPA conflict (LAN)—SNPA conflict.

· Smaller than header—The packet length is smaller than the fixed header length.

· Bad protocol description—Invalid protocol description.

· Bad protocol ID—Invalid protocol identifier.

· Bad protocol version—Invalid protocol version.

· Unknown packet type—Unknown packet type.

· Bad max area count—Invalid maximum number of area addresses.

· No active NBR—The packet is from an unknown neighbor.

· Bad system ID length—Invalid system ID length.

· Mismatched level—Mismatched levels.

· Illegal IS type—Invalid IS type.

· Sequence number is 0—The sequence number is 0.

· Checksum is 0—The checksum is 0.

· Incorrect checksum—Incorrect checksum.

· Bad TLV length—Invalid TLV length.

· Mismatched protocol—Mismatched protocols.

· Bad auth TLV—Invalid authentication TLV.

· Auth failure—Authentication failure.

· Excessive auth TLVs—Excessive authentication TLVs.

· Bad NBR TLV—Invalid neighbor TLV.

· Bad extended IS TLV—Invalid extended IS TLV.

· Bad IF address TLV—Invalid interface address TLV.

· Bad IPv6 IF address TLV—Invalid IPv6 interface address TLV.

· Bad alias TLV—Invalid alias TLV.

· Bad IP reachability TLV—Invalid IP reachability TLV.

· Bad MT IS TLV—Invalid topology IS TLV.

· Bad area address TLV—Invalid area address TLV.

· Bad MT ID TLV—Invalid topology ID TLV.

· Bad MT IP TLV—Invalid IPv4 topology TLV.

· Bad MT IPv6 TLV—Invalid IPv6 topology TLV.

· Bad IPv6 reachability TLV—Invalid IPv6 reachability TLV.

· Bad router ID TLV—Invalid router ID TLV.

· Bad SRLG TLV—Invalid SRLG TLV.

· Bad IID TLV—The multi-instance TLV length is smaller than the minimum length specified in the protocol.

# Display detailed CSNP packet statistics on a per-interface basis.

<Sysname> display isis packet csnp by-interface verbose

CSNP packet information for IS-IS(1)

------------------------------------

Interface: Vlan-interface10

Total output packets : 0 Total output error packets : 0

Total input packets : 0 Total input error packets : 0

Input packets with errors

Bad packet length : 0 Bad header length : 0

Jumbo packet : 0 SNPA conflict (LAN) : 0

Smaller than header : 0 Bad protocol description : 0

Bad protocol ID : 0 Bad protocol version : 0

Unknown packet type : 0 Bad max area count : 0

No active NBR : 0 Bad system ID length : 0

Mismatched level : 0 Bad TLV length : 0

Auth failure : 0 Bad auth TLV : 0

Bad LSP TLV length : 0 Excessive auth TLVs : 0

Excessive LSPs : 0 Bad LSP ID : 0

Bad IID TLV : 0

# Display detailed CSNP packet statistics.

<Sysname> display isis packet csnp verbose

CSNP packet information for IS-IS(1)

------------------------------------

Total output packets : 0 Total output error packets : 0

Total input packets : 0 Total input error packets : 0

Input packets with errors

Bad packet length : 0 Bad header length : 0

Jumbo packet : 0 SNPA conflict (LAN) : 0

Smaller than header : 0 Bad protocol description : 0

Bad protocol ID : 0 Bad protocol version : 0

Unknown packet type : 0 Bad max area count : 0

No active NBR : 0 Bad system ID length : 0

Mismatched level : 0 Bad TLV length : 0

Auth failure : 0 Bad auth TLV : 0

Bad LSP TLV length : 0 Excessive auth TLVs : 0

Excessive LSPs : 0 Bad LSP ID : 0

Bad IID TLV : 0

Table 17 Command output

Field	Description
Input packets with errors	Statistics for packets with the following errors: · Bad packet length—Invalid packet length. · Bad header length—Invalid header length. · Jumbo packet—The packet length exceeds the maximum length of packets that can be received. · SNPA conflict (LAN)—SNPA conflict. · Smaller than header—The packet length is smaller than the fixed header length. · Bad protocol description—Invalid protocol description. · Bad protocol ID—Invalid protocol identifier. · Bad protocol version—Invalid protocol version. · Unknown packet type—Unknown packet type. · Bad max area count—Invalid maximum number of area addresses. · No active NBR—The packet is from an unknown neighbor. · Bad system ID length—Invalid system ID length. · Mismatched level—Mismatched levels. · Bad TLV length—Invalid TLV length. · Auth failure—Authentication failure. · Bad auth TLV—Invalid authentication TLV. · Bad LSP TLV length—Invalid LSP TLV length. · Excessive auth TLVs—Excessive authentication TLVs. · Excessive LSPs—Excessive LSPs. · Bad LSP ID—Invalid LSP ID. · Bad IID TLV—The multi-instance TLV length is smaller than the minimum length specified in the protocol.

Field

Description

Input packets with errors

Statistics for packets with the following errors:

· Bad packet length—Invalid packet length.

· Bad header length—Invalid header length.

· Jumbo packet—The packet length exceeds the maximum length of packets that can be received.

· SNPA conflict (LAN)—SNPA conflict.

· Smaller than header—The packet length is smaller than the fixed header length.

· Bad protocol description—Invalid protocol description.

· Bad protocol ID—Invalid protocol identifier.

· Bad protocol version—Invalid protocol version.

· Unknown packet type—Unknown packet type.

· Bad max area count—Invalid maximum number of area addresses.

· No active NBR—The packet is from an unknown neighbor.

· Bad system ID length—Invalid system ID length.

· Mismatched level—Mismatched levels.

· Bad TLV length—Invalid TLV length.

· Auth failure—Authentication failure.

· Bad auth TLV—Invalid authentication TLV.

· Bad LSP TLV length—Invalid LSP TLV length.

· Excessive auth TLVs—Excessive authentication TLVs.

· Excessive LSPs—Excessive LSPs.

· Bad LSP ID—Invalid LSP ID.

· Bad IID TLV—The multi-instance TLV length is smaller than the minimum length specified in the protocol.

# Display detailed PSNP packet statistics on a per-interface basis.

<Sysname> display isis packet psnp by-interface verbose

PSNP packet information for IS-IS(1)

------------------------------------

Interface: Vlan-interface10

Total output packets : 0 Total output error packets : 0

Total input packets : 0 Total input error packets : 0

Input packets with errors

Bad packet length : 0 Bad header length : 0

Jumbo packet : 0 SNPA conflict (LAN) : 0

Smaller than header : 0 Bad protocol description : 0

Bad protocol ID : 0 Bad protocol version : 0

Unknown packet type : 0 Bad max area count : 0

No active NBR : 0 Bad system ID length : 0

Mismatched level : 0 Bad TLV length : 0

Auth failure : 0 Bad auth TLV : 0

Bad LSP TLV length : 0 Excessive auth TLVs : 0

Excessive LSPs : 0 Bad LSP ID : 0

Bad IID TLV : 0

# Display detailed PSNP packet statistics.

<Sysname> display isis packet psnp verbose

PSNP packet information for IS-IS(1)

------------------------------------

Total output packets : 0 Total output error packets : 0

Total input packets : 0 Total input error packets : 0

Input packets with errors

Bad packet length : 0 Bad header length : 0

Jumbo packet : 0 SNPA conflict (LAN) : 0

Smaller than header : 0 Bad protocol description : 0

Bad protocol ID : 0 Bad protocol version : 0

Unknown packet type : 0 Bad max area count : 0

No active NBR : 0 Bad system ID length : 0

Mismatched level : 0 Bad TLV length : 0

Auth failure : 0 Bad auth TLV : 0

Bad LSP TLV length : 0 Excessive auth TLVs : 0

Excessive LSPs : 0 Bad LSP ID : 0

Bad IID TLV : 0

Table 18 Command output

Field	Description
Input packets with errors	Statistics for packets with the following errors: · Bad packet length—Invalid packet length. · Bad header length—Invalid header length. · Jumbo packet—The packet length exceeds the maximum length of packets that can be received. · SNPA conflict (LAN)—SNPA conflict. · Smaller than header—The packet length is smaller than the fixed header length. · Bad protocol description—Invalid protocol description. · Bad protocol ID—Invalid protocol identifier. · Bad protocol version—Invalid protocol version. · Unknown packet type—Unknown packet type. · Bad max area count—Invalid maximum number of area addresses. · No active NBR—The packet is from an unknown neighbor. · Bad system ID length—Invalid system ID length. · Mismatched level—Mismatched levels. · Bad TLV length—Invalid TLV length. · Auth failure—Authentication failure. · Bad auth TLV—Invalid authentication TLV. · Bad LSP TLV length—Invalid LSP TLV length. · Excessive auth TLVs—Excessive authentication TLVs. · Excessive LSPs—Excessive LSPs. · Bad LSP ID—Invalid LSP ID. · Bad IID TLV—The multi-instance TLV length is smaller than the minimum length specified in the protocol.

Field

Description

Input packets with errors

Statistics for packets with the following errors:

· Bad packet length—Invalid packet length.

· Bad header length—Invalid header length.

· Jumbo packet—The packet length exceeds the maximum length of packets that can be received.

· SNPA conflict (LAN)—SNPA conflict.

· Smaller than header—The packet length is smaller than the fixed header length.

· Bad protocol description—Invalid protocol description.

· Bad protocol ID—Invalid protocol identifier.

· Bad protocol version—Invalid protocol version.

· Unknown packet type—Unknown packet type.

· Bad max area count—Invalid maximum number of area addresses.

· No active NBR—The packet is from an unknown neighbor.

· Bad system ID length—Invalid system ID length.

· Mismatched level—Mismatched levels.

· Bad TLV length—Invalid TLV length.

· Auth failure—Authentication failure.

· Bad auth TLV—Invalid authentication TLV.

· Bad LSP TLV length—Invalid LSP TLV length.

· Excessive auth TLVs—Excessive authentication TLVs.

· Excessive LSPs—Excessive LSPs.

· Bad LSP ID—Invalid LSP ID.

· Bad IID TLV—The multi-instance TLV length is smaller than the minimum length specified in the protocol.

Related commands

reset isis packet

display isis peer

Use display isis peer to display IS-IS neighbor information.

Syntax

display isis peer [ statistics | verbose ] [ process-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

statistics: Displays IS-IS neighbor statistics.

verbose: Displays detailed IS-IS neighbor information. If you do not specify this keyword, the command displays brief IS-IS neighbor information.

process-id: Displays IS-IS neighbor information for an IS-IS process specified by its ID in the range of 1 to 65535. If you do not specify this argument, the command displays neighbor information for all IS-IS processes.

Examples

# Display brief IS-IS neighbor information.

<Sysname> display isis peer

Peer information for IS-IS(1)

-----------------------------

System ID: 0000.0000.0001

Interface: Vlan100 Circuit Id: 0000.0000.0001.01

State: Up HoldTime: 27s Type: L1(L1L2) PRI: 64

System ID: 0000.0000.0001

Interface: Vlan100 Circuit Id: 0000.0000.0001.01

State: Up HoldTime: 27s Type: L2(L1L2) PRI: 64

# Display detailed IS-IS neighbor information.

<Sysname> display isis peer verbose

Peer information for IS-IS(1)

----------------------------

System ID: 0000.1111.2222

Interface: Vlan100 Circuit Id: 0000.1111.2222.01

State: Up Holdtime: 6s Type: L1(L1L2) PRI: 64

Area address(es): 49

Peer IP address(es): 12.0.0.2

Peer IPv6 address(es): FE80::541F:98FF:FE5E:205

Peer IPv6 global address(es): 100::2

Peer local circuit ID: 1

Peer circuit SNPA address: 000c-293b-c4be

Uptime: 00:05:07

Adj protocol: IPv4

IPv4 adjacency state: Up

Adj P2P three-way handshake: No

Graceful Restart capable

Restarting signal: No

Suppress adjacency advertisement: No

Local topology:

0 2

Remote topology:

0 2

Local BFD support:

(MTID:0, IPv4)

Remote BFD support:

(MTID:0, IPv4)

System ID: 0000.0000.0002

Interface: Vlan101 Circuit Id: 001

State: Up HoldTime: 27s Type: L1L2 PRI: --

Area address(es): 49

Peer IP address(es): 192.168.220.30

Peer local circuit ID: 1

Peer circuit SNPA address: 000c-29fd-ed69

Uptime: 00:05:07

Adj protocol: IPv4

Adj P2P three-way handshake: Yes

Peer extended circuit ID: 2

Graceful Restart capable

Restarting signal: No

Suppress adjacency advertisement: No

Local topology:

Remote topology:

Local BFD support:

(MTID:0, IPv4)

Remote BFD support:

(MTID:0, IPv4)

Table 19 Command output

Field	Description
System ID	System ID of the neighbor.
Interface	Interface connecting to the neighbor.
Circuit Id	Circuit ID.
State	Circuit state.
HoldTime	Within the holdtime, if no hellos are received from the neighbor, the neighbor is considered down. If a hello is received, the holdtime is reset to the initial value.
Type	Circuit type: · L1—Means the circuit type is Level-1 and the neighbor is a Level-1 router. · L2—Means the circuit type is Level-2 and the neighbor is a Level-2 router. · L1(L1L2)—Means the circuit type is Level-1 and the neighbor is a Level-1-2 router. · L2(L1L2)—Means the circuit type is Level-2 and the neighbor is a Level-1-2 router.
PRI	DIS priority of the neighbor.
Area address(es)	Area address of the neighbor.
Peer IP address(es)	IP address of the neighbor.
Peer IPv6 addresses(es)	IPv6 address of the neighbor.
Peer IPv6 global address(es)	Global unicast IPv6 address of the remote interface.
Uptime	Time elapsed since the neighbor relationship was formed.
Adj Protocol	Adjacency protocol: IPv4 or IPv6.
IPv4 adjacency state	IPv4 adjacency state: Up or Down. This field is not displayed if IPv4 is not supported.
IPv6 adjacency state	IPv6 adjacency state: Up or Down. This field is not displayed if IPv6 is not supported.
Adjacency not up	Reason why the adjacency relationship is down: Waiting for BFD session to come up. This field is no longer displayed after the adjacency relationship comes up.
Peer local circuit ID	Circuit ID of the neighbor.
Peer circuit SNPA address	SNPA address of the neighbor.
Adj P2P three-way handshake	Indicates whether the neighbor supports P2P three-way handshake.
Peer extended circuit ID	Extended circuit ID of the neighbor interface. This field is available when the neighbor supports three-way handshake.
Graceful Restart capable	The neighbor has the GR helper capability.
Restarting signal	RR flag.
Suppress adjacency advertisement	SA flag.
Local topology	List of topologies supported by the local interface.
Remote topology	List of topologies supported by the neighbor interface.
Local BFD support	Support of the local end for adjacency establishment and maintenance control based on BFD session state: · (MTID:0, IPv4)—Adjacency establishment and maintenance control based on BFD session state is supported in IPv4 unicast topology 0. · (MTID:0, IPv6)—Adjacency establishment and maintenance control based on BFD session state is supported in IPv6 unicast topology 0. This field is not displayed if the local end does not support adjacency establishment and maintenance control based on BFD session state.
Remote BFD support	Support of the remote end for adjacency establishment and maintenance control based on BFD session state: · (MTID:0, IPv4)—Adjacency establishment and maintenance control based on BFD session state is supported in IPv4 unicast topology 0. · (MTID:0, IPv6)—Adjacency establishment and maintenance control based on BFD session state is supported in IPv6 unicast topology 0. This field is not displayed if the remote end does not support adjacency establishment and maintenance control based on BFD session state.

‌

# Display IS-IS neighbor statistics.

<Sysname> display isis peer statistics

Peer Statistics information for IS-IS(1)

---------------------------------------

Type IPv4 Up/Init IPv6 Up/Init

LAN Level-1 1/0 0/0

LAN Level-2 1/0 0/0

P2P 0/0 0/0

Table 20 Command output

Field	Description
Type	Neighbor type: · LAN Level-1—Number of Level-1 neighbors whose network type is broadcast. · LAN Level-2—Number of Level-2 neighbors whose network type is broadcast. · P2P—Number of neighbors whose network type is P2P.
IPv4 Up	Number of IPv4 neighbors in up state.
IPv4 Init	Number of IPv4 neighbors in init state.
IPv6 Up	Number of IPv6 neighbors in up state.
IPv6 Init	Number of IPv6 neighbors in init state.

‌

display isis redistribute

Use display isis redistribute to display the redistributed IS-IS routing information.

Syntax

display isis redistribute [ ipv4 [ ip-address mask-length ] | ipv6 [ ipv6-address prefix-length ] ] [ level-1 | level-2 ] [ process-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ipv4: Displays the redistributed IPv4 routing information.

ip-address mask-length: Specifies the destination IP address and mask length.

ipv6: Displays the redistributed IPv6 routing information.

ipv6-address prefix-length: Specifies the destination IPv6 address and prefix length. The value range for the prefix-length argument is 1 to 128.

process-id: Specifies the IS-IS process by its ID in the range of 1 to 65535.

level-1: Displays the IS-IS Level-1 routing information.

level-2: Displays the IS-IS Level-2 routing information.

Usage guidelines

If you specify neither the ipv4 nor ipv6 keyword, the command displays the redistributed IPv4 routing information.

If you do not specify an IS-IS level, this command displays both Level-1 and Level-2 routing information.

Examples

# Display redistributed IPv4 routing information.

<Sysname> display isis redistribute 1

Route information for IS-IS(1)

------------------------------

Level-1 IPv4 Redistribute Table

--------------------------------

Type IPv4 Destination IntCost ExtCost Tag State

--------------------------------------------------------------------------------

D 192.168.30.0/24 0 0 Active

D 11.11.11.11/32 0 0

D 10.10.10.0/24 0 0

Type: D -Direct, I -ISIS, S -Static, O -OSPF, B -BGP, R -RIP, E -EIGRP

Table 21 Command output

Field	Description
Route information for IS-IS(1)	IS-IS process of the redistributed routing information.
Level-1 IPv4 Redistribute Table	Redistributed IPv4 routing information of IS-IS Level-1.
Level-2 IPv4 Redistribute Table	Redistributed IPv4 routing information of IS-IS Level-2.
Type	Redistributed route type.
IPV4 Destination	IPv4 destination address.
IntCost	Internal cost of the route.
ExtCost	External cost of the route.
Tag	Tag value.
State	Indicates whether the route is valid.

‌

# Display information about redistributed IPv6 IS-IS routes.

<Sysname> display isis redistribute ipv6 1

Route information for IS-IS(1)

------------------------------

Level-1 IPv6 Redistribute Table

--------------------------------

Type : direct Destination: 12:1::/64

IntCost : 0 Tag :

State : Active

Level-2 IPv6 Redistribute Table

--------------------------------

Type : direct Destination: 12:1::/64

IntCost : 0 Tag :

State : Active

Table 22 Command output

Field	Description
Route information for IS-IS(1)	Redistributed route information for IS-IS process 1.
Level-1 IPv6 Redistribute Table	Redistributed route information of IS-IS Level-1.
Level-2 IPv6 Redistribute Table	Redistributed route information of IS-IS Level-2.
Type	Redistributed route types, including direct, IS-ISv6, static, OSPFv3, BGP4+, RIPng, and UNR.
Destination	IPv6 destination address.
IntCost	Internal route cost.
Tag	Tag value.
State	Indicates whether the redistributed route is valid.

display isis route

Use display isis route to display IS-IS routing information.

Syntax

display isis route [ ipv4 [ ip-address mask-length ] | ipv6 [ ipv6-address prefix-length ] ] [ [ level-1 | level-2 ] | verbose ] * [ process-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ipv4: Displays IS-IS IPv4 routing information.

ip-address mask-length: Displays IS-IS IPv4 routing information for the specified IP address. The mask-length argument is in the range of 0 to 32.

ipv6: Displays IS-IS IPv6 routing information.

ipv6-address prefix-length: Displays IS-IS IPv6 routing information for the specified IPv6 address. The prefix-length argument is in the range of 0 to 128.

level-1: Displays Level-1 IS-IS routing information.

level-2: Displays Level-2 IS-IS routing information.

verbose: Displays detailed IS-IS IPv4 routing information. If you do not specify this keyword, the command displays brief IS-IS IPv4 routing information

process-id: Displays IS-IS IPv4 routing information for an IS-IS process specified by its ID in the range of 1 to 65535. If you do not specify an IS-IS process, this command displays routing information for all IS-IS processes.

Usage guidelines

If you specify neither the ipv4 nor ipv6 keyword, the command displays IS-IS IPv4 routing information.

If you do not specify a level, this command displays both Level-1 and Level-2 routing information.

Examples

# Display brief IS-IS IPv4 routing information.

<Sysname> display isis route

Route information for IS-IS(1)

-----------------------------

Level-1 IPv4 Forwarding Table

-----------------------------

IPv4 Destination IntCost ExtCost ExitInterface NextHop Flags

-------------------------------------------------------------------------------

8.8.8.0/24 10 NULL Vlan100 Direct D/L/-

9.9.9.0/24 20 NULL Vlan100 8.8.8.5 R/L/-

Flags: D-Direct, R-Added to Rib, L-Advertised in LSPs, U-Up/Down Bit Set

Level-2 IPv4 Forwarding Table

-----------------------------

IPv4 Destination IntCost ExtCost ExitInterface NextHop Flags

-------------------------------------------------------------------------------

8.8.8.0/24 10 NULL D/L/-

Flags: D-Direct, R-Added to Rib, L-Advertised in LSPs, U-Up/Down Bit Set

Table 23 Command output

Field	Description
Route information for IS-IS(1)	Route information for IS-IS process 1.
Level-1 IPv4 Forwarding Table	IS-IS IPv4 routing information for Level-1.
Level-2 IPv4 Forwarding Table	IS-IS IPv4 routing information for Level-2.
IPv4 Destination	IPv4 destination address.
IntCost	Internal cost.
ExtCost	External cost.
ExitInterface	Output interface.
NextHop	Next hop.
Flags	Routing state flag: · D—Direct route. · R—The route has been added into the routing table. · L—The route has been advertised in an LSP. · U—Penetration flag. Setting it to UP can prevent an LSP sent from L2 to L1 from being sent back to L2.

# Display detailed IS-IS IPv4 routing information.

<Sysname> display isis route verbose

Route information for IS-IS(1)

-----------------------------

Level-1 IPv4 Forwarding Table

-----------------------------

IPV4 Dest : 8.8.8.0/24 Int. Cost : 10 Ext. Cost : NULL

Admin Tag : - Src Count : 2 Flag : D/L/-

InLabel : 4294967295 InLabel Flag: -/-/-/-/-/-

NextHop : Interface : ExitIndex :

Direct Vlan100 0x00000000

Nib ID : 0x0 OutLabel : 4294967295 OutLabelFlag: -

LabelSrc : N/A Delay Flag : N/A

IPV4 Dest : 9.9.9.0/24 Int. Cost : 20 Ext. Cost : NULL

Admin Tag : - Src Count : 1 Flag : R/L/-

InLabel : 4294967295 InLabel Flag: -/-/-/-/-/-

NextHop : Interface : ExitIndex :

8.8.8.5 Vlan100 0x00000003

Nib ID : 0x0 OutLabel : 4294967295 OutLabelFlag: -

LabelSrc : N/A Delay Flag : N/A

Remote-LFA:

Interface : Vlan101

BkNextHop : 31.1.1.3 LsIndex : 0x01000002

Tunnel destination address: 4.4.4.9

Backup label: {2174}

TI-LFA:

Interface : Vlan100

BkNextHop : 104.1.1.1 LsIndex : 0x000001

Backup label stack(top->bottom): {16020, 2174}

Route label: 4294967295

Flags: D-Direct, R-Added to Rib, L-Advertised in LSPs, U-Up/Down Bit Set

InLabel flags: R-Readvertisement, N-Node SID, P-no PHP

E-Explicit null, V-Value, L-Local

OutLabelFlags: E-Explicit null, I-Implicit null, N-Normal, P-SR label prefer

Level-2 IPv4 Forwarding Table

-----------------------------

IPV4 Dest : 8.8.8.0/24 Int. Cost : 10 Ext. Cost : NULL

Admin Tag : - Src Count : 2 Flag : D/L/-

InLabel : 4294967295 InLabel Flag: -/-/-/-/-/-

NextHop : Interface : ExitIndex :

Direct Vlan100 0x00000001

Nib ID : 0x14000003 OutLabel : 4294967295 OutLabelFlag: -

LabelSrc : N/A Delay Flag : N/A

Flags: D-Direct, R-Added to Rib, L-Advertised in LSPs, U-Up/Down Bit Set

InLabel flags: R-Readvertisement, N-Node SID, P-no PHP

E-Explicit null, V-Value, L-Local

OutLabelFlags: E-Explicit null, I-Implicit null, N-Normal, P-SR label prefer

Table 24 Command output

Field	Description
Route information for IS-IS(1)	Route information for IS-IS process 1.
Level-1 IPv4 Forwarding Table	IS-IS IPv4 routing information for Level-1.
Level-2 IPv4 Forwarding Table	IS-IS IPv4 routing information for Level-2.
IPV4 Dest	IPv4 destination.
Int. Cost	Internal cost.
Ext. Cost	External cost.
Admin Tag	Tag.
Src Count	Count of advertising sources.
Flag	Route state flag: · R—The route has been installed into the routing table. · L—The route has been flooded in an LSP. · U—Route leaking flag. Setting it to UP can prevent an LSP sent from L2 to L1 from being sent back to L2.
Next Hop	Next hop.
Interface	Output interface.
ExitIndex	Index of the output interface.
Nib ID	ID assigned by the routing management module (next hop index).
InLabel	Incoming label.
LabelSrc	Label source: · SR—The label is allocated by the SR node. · SRMS—The label is allocated by the segment routing mapping server (SRMS). · N/A—No label exists.
Delay Flag	Microloop avoidance delay flag: · D—Microloop avoidance is configured. Route convergence is delayed. · N/A—Microloop avoidance is not configured or the microloop avoidance delay timer has expired. Route convergence is in progress.
InLabel flag	Incoming label flag: · R—Re-advertisement flag. If set, inter-level propagation or route redistribution exists. · N—Node-SID flag. If set, the prefix SID is the SID to an SR node. · P—No-PHP flag. If set, the penultimate node cannot pop the prefix SID. · E—Explicit null flag. If set, the upstream neighbor must replace the prefix SID with an explicit null flag before forwarding the packets. · V—Value/Index flag. If set, the prefix SID carries an absolute value. · L—Local flag. If set, the prefix SID has local significance.
OutLabel	Outgoing label.
OutLabelFlag	Outgoing label flag: · E—Explicit null flag. The upstream neighbor must replace the SID with an explicit null flag before forwarding the packets. · I—Implicit null flag. The upstream neighbor must replace the SID with an implicit null flag before forwarding the packets. This flag is not supported in the current software version. · N—Normal flag. · P—SR label preferred flag.
TI-LFA	TI-LFA backup information.
BKNextHop	TI-LFA/Remote LFA backup next hop.
LsIndex	Label stack index.
Backup label stack(top->bottom)	Backup path label stack. N/A indicates that no label stack exists.
Remote-LFA	Remote LFA backup information.
Tunnel destination address	LDP tunnel destination address.
Backup label	Backup label to the PQ node. N/A indicates that no label exists.

# Display IPv6 IS-IS routing information.

<Sysname> display isis route ipv6

Route information for IS-IS(1)

------------------------------

Level-1 IPv6 forwarding table

-----------------------------

Destination: 2001:1:: PrefixLen: 64

Flag : R/L/- Cost : 20

Next hop : FE80::200:5EFF:FE64:8905 Interface: Vlan100

Destination: 2001:2:: PrefixLen: 64

Flag : D/L/- Cost : 10

Next hop : Direct Interface: Vlan100

Flags: D-Direct, R-Added to Rib, L-Advertised in LSPs, U-Up/Down Bit Set

Level-2 IPv6 forwarding table

-----------------------------

Destination: 2001:1:: PrefixLen: 64

Flag : -/-/- Cost : 20

Destination: 2001:2:: PrefixLen: 64

Flag : D/L/- Cost : 10

Flags: D-Direct, R-Added to Rib, L-Advertised in LSPs, U-Up/Down Bit Set

Table 25 Command output

Field	Description
Destination	IPv6 destination prefix.
PrefixLen	Prefix length.
Flag/Flags	Route flag: · D—This is a direct route. · R—The route has been added into the routing table. · L—The route has been advertised in an LSP. · U—Route leaking flag, indicating that the Level-1 route is from Level-2. U means the route will not be returned to Level-2.
Cost	Route cost.
Next hop	Next hop.
Interface	Output interface.

# Display detailed IPv6 IS-IS routing information.

<Sysname> display isis route ipv6 verbose

Route information for IS-IS(1)

------------------------------

Level-1 IPv6 forwarding table

-----------------------------

IPv6 dest : 2001:1::/64

Flag : D/L/- Cost : 10

Admin tag : - Src count : 2

Nexthop : Direct

Interface : Vlan101

Nib ID : 0x0

IPv6 dest : 2001:2::/64

Flag : R/-/- Cost : 20

Admin tag : - Src count : 2

Nexthop : FE80::200:5EFF:FE64:8905

Interface : Vlan101

BkNexthop : FE80::200:5EFF:FE64:8905

BkInterface : Vlan101

Nib ID : 0x24000002

Flags: D-Direct, R-Added to Rib, L-Advertised in LSPs, U-Up/Down Bit Set

Level-2 IPv6 Forwarding table

-----------------------------

IPv6 dest : 2001:1::/64

Flag : D/L/- Cost : 10

Admin tag : - Src count : 2

Nexthop : -

Interface : -

Nib ID : -

IPv6 dest : 2001:2::/64

Flag : D/L/- Cost : 10

Admin tag : - Src count : 2

Nexthop : -

Interface : -

Nib ID : -

Flags: D-Direct, R-Added to Rib, L-Advertised in LSPs, U-Up/Down Bit Set

Table 26 Command output

Field	Description
IPv6 dest	IPv6 destination address and prefix.
Flag/Flags	Route flag: · D—The route is a direct route. · R—The route has been added into the routing table. · L—The route has been advertised in an LSP. · U—Route leaking flag, indicating the Level-1 route is from Level-2. U means the route will not be returned to Level-2.
Cost	Route cost.
Admin tag	Administrative tag.
Src count	Number of advertisement sources.
Nexthop	Next hop.
Interface	Output interface.
BkNexthop	Backup next hop.
BkInterface	Backup output interface.
Nib ID	Next hop index assigned by the routing management module.

display isis spf-tree

Use display isis spf-tree to display IS-IS IPv4 SPF tree information.

Syntax

display isis spf-tree [ ipv4 | ipv6 ] [ [ level-1 | level-2 ] | [ source-id source-id | verbose ] ] * [ process-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ipv4: Displays IS-IS IPv4 SPF tree information.

ipv6: Displays IS-IS IPv6 SPF tree information.

level-1: Displays Level-1 IS-IS SPF tree information. If you do not specify a level, the command displays both Level-1 and Level-2 SPF tree information.

level-2: Displays Level-2 SPF tree information. If you do not specify a level, the command displays both Level-1 and Level-2 SPF tree information.

source-id source-id: Displays detailed information about an SPF node. The source-id argument represents the system ID of the SPF node, in XXXX.XXXX.XXXX.XX format.

verbose: Displays detailed IS-IS SPF tree information. If you do not specify this keyword, the command displays brief IS-IS SPF tree information.

process-id: Specifies an IS-IS process by its ID in the range of 1 to 65535. If you do not specify this argument, the command displays SPF tree information for all IS-IS processes.

Usage guidelines

If you specify neither the ipv4 nor ipv6 keyword, the command displays IS-IS IPv4 SPF tree information.

Examples

# Display brief IS-IS IPv4 SPF tree information.

<Sysname> display isis spf-tree

Shortest Path Tree for IS-IS(1)

-------------------------------

Flags: S-Node is on SPF tree T-Node is on tent list

O-Node is overload R-Node is directly reachable

I-Node or Link is isolated D-Node or Link is to be deleted

C-Neighbor is child P-Neighbor is parent

V-Link is involved N-Link is a new path

L-Link is on change list U-Protocol usage is changed

H-Nexthop is changed

Level-1 Shortest Path Tree

--------------------------

SpfNode NodeFlag SpfLink LinkCost LinkFlag

-------------------------------------------------------------------------------

0000.0000.0032.00 S/-/-/-/-/-

-->0000.0000.0032.01 10 -/-/C/-/-/-/-/-/-

-->0000.0000.0064.00 10 -/-/C/-/-/-/-/-/-

0000.0000.0032.01 S/-/-/R/-/-

-->0000.0000.0064.00 0 -/-/C/-/-/-/-/-/-

-->0000.0000.0032.00 0 -/-/-/P/-/-/-/-/-

0000.0000.0064.00 S/-/-/R/-/-

-->0000.0000.0032.00 10 -/-/-/P/-/-/-/-/-

-->0000.0000.0032.01 10 -/-/-/P/-/-/-/-/-

Level-2 Shortest Path Tree

--------------------------

SpfNode NodeFlag SpfLink LinkCost LinkFlag

-------------------------------------------------------------------------------

0000.0000.0032.00 S/-/-/-/-/-

-->0000.0000.0032.01 10 -/-/C/-/-/-/-/-/-

-->0000.0000.0064.00 10 -/-/C/-/-/-/-/-/-

0000.0000.0032.01 S/-/-/R/-/-

-->0000.0000.0064.00 0 -/-/C/-/-/-/-/-/-

-->0000.0000.0032.00 0 -/-/-/P/-/-/-/-/-

0000.0000.0064.00 S/-/-/R/-/-

-->0000.0000.0032.00 10 -/-/-/P/-/-/-/-/-

-->0000.0000.0032.01 10 -/-/-/P/-/-/-/-/-

# Display detailed IS-IS IPv4 SPF tree information.

<Sysname> display isis spf-tree verbose

Shortest Path Tree for IS-IS(1)

-------------------------------

Flags: S-Node is on SPF tree T-Node is on tent list

O-Node is overload R-Node is directly reachable

I-Node or Link is isolated D-Node or Link is to be deleted

C-Neighbor is child P-Neighbor is parent

V-Link is involved N-Link is a new path

L-Link is on change list U-Protocol usage is changed

H-Nexthop is changed

Level-1 Shortest Path Tree

--------------------------

SpfNode : 0000.0000.0003.01

Distance : 20

TE distance : 20

NodeFlag : S/-/-/-/-/-

RelayNibID : 0x0

TE tunnel count: 0

Nexthop count : 1

Neighbor : 0000.0000.0002.00 Interface : Vlan100

Nexthop : 101.1.1.2

BkNeighbor : N/A BkInterface: N/A

BkNexthop : N/A

Remote-LFA :

Protect : Link

RLFANeighbor: 0000.0000.0003.00

PQNode : 0000.0000.0004.00

PQNodePrefix: 4.4.4.9/32

OutLabel : 2174

TI-LFA:

TiLfaNeighbor : 0000.0000.0004.00 TiLfaInterface: Vlan400

TiLfaNexthop : 104.1.1.1

PNode SrcID : 0000.0000.0003.00 QNode SrcID : 0000.0000.0002.00

PNode prefix : 33.33.33.33 PNode SidIndex: 20

Protect : Link

Label stack : {16020, 2174}

SpfLink count : 2

-->0000.0000.0002.00

LinkCost : 0

LinkNewCost : 0

LinkFlag : -/-/-/P/-/-/-/-/-

LinkSrcCnt : 1

Type : Remote Interface: N/A

Cost : 0 Nexthop : N/A

-->0000.0000.0003.00

LinkCost : 0

LinkNewCost : 0

LinkFlag : -/-/C/-/-/-/-/-/-

LinkSrcCnt : 1

Type : Remote Interface: N/A

Cost : 0 Nexthop : N/A

SpfNode : 0000.0000.0004.00

Distance : 10

Te Distance : 10

NodeFlag : S/-/-/-/-/-

RelayNibID : 0x14000000

TE tunnel count: 1

Destination: 4.4.4.4 Interface : Tun0

TE cost : 10 Final cost : 10

Add nexthop: YES Add TLV : YES

Nexthop count : 2

Neighbor : 0000.0000.0004.00 Interface : Tun0

Nexthop : 4.4.4.4

BkNeighbor : N/A BkInterface: N/A

BkNexthop : N/A

Neighbor : 0000.0000.0004.00 Interface : Vlan50

Nexthop : 1.1.1.3

BkNeighbor : N/A BkInterface: N/A

BkNexthop : N/A

SpfLink count : 1

-->0000.0000.0004.04

LinkCost : 10

LinkNewCost : 10

LinkFlag : -/-/-/P/-/-/-/-/-

LinkSrcCnt : 1

Type: Remote Interface: N/A

Cost: 10 Nexthop : N/A

AdvMtID: 0

SpfNode : 0000.0000.0004.04

Distance : 10

TE distance : 10

NodeFlag : S/-/-/R/-/-

RelayNibID : 0x14000001

TE tunnel count: 0

Nexthop count : 0

SpfLink count : 2

-->0000.0000.0001.00

LinkCost : 0

LinkNewCost : 0

LinkFlag : -/-/-/P/-/-/-/-/-

LinkSrcCnt : 1

Type: Remote Interface: N/A

Cost: 0 Nexthop : N/A

-->0000.0000.0004.00

LinkCost : 0

LinkNewCost : 0

LinkFlag : -/-/C/-/-/-/-/-/-

LinkSrcCnt : 1

Type: Remote Interface: Vlan50

Cost: 0 Nexthop : 1.1.1.3

Level-2 Shortest Path Tree

--------------------------

SpfNode : 0000.0000.0003.01

Distance : 20

TE distance : 20

NodeFlag : S/-/-/-/-/-

RelayNibID : 0x0

TE tunnel count: 0

Nexthop count : 1

Neighbor : 0000.0000.0002.00 Interface : Vlan100

Nexthop : 101.1.1.2

BkNeighbor : N/A BkInterface: N/A

BkNexthop : N/A

SpfLink count : 2

-->0000.0000.0002.00

LinkCost : 0

LinkNewCost : 0

LinkFlag : -/-/-/P/-/-/-/-/-

LinkSrcCnt : 1

Type : Remote Interface: N/A

Cost : 0 Nexthop : N/A

-->0000.0000.0003.00

LinkCost : 0

LinkNewCost : 0

LinkFlag : -/-/C/-/-/-/-/-/-

LinkSrcCnt : 1

Type : Remote Interface: N/A

Cost : 0 Nexthop : N/A

SpfNode : 0000.0000.0004.00

Distance : 10

TE distance : 10

NodeFlag : S/-/-/-/-/-

RelayNibID : 0x0

TE tunnel count: 1

Destination: 4.4.4.4 Interface : Tun0

TE cost : 10 Final cost : 10

Add nexthop: YES Add TLV : YES

Nexthop count : 2

Neighbor : 0000.0000.0004.00 Interface : Tun0

Nexthop : 4.4.4.4

BkNeighbor : N/A BkInterface: N/A

BkNexthop : N/A

Neighbor : 0000.0000.0004.00 Interface : Vlan50

Nexthop : 1.1.1.3

BkNeighbor : N/A BkInterface: N/A

BkNexthop : N/A

SpfLink count : 1

-->0000.0000.0004.04

LinkCost : 10

LinkNewCost : 10

LinkFlag : -/-/-/P/-/-/-/-/-

LinkSrcCnt : 1

Type: Remote Interface: N/A

Cost: 10 Nexthop : N/A

AdvMtID: 0

SpfNode : 0000.0000.0004.04

Distance : 10

TE distance : 10

NodeFlag : S/-/-/R/-/-

RelayNibID : 0x0

TE tunnel count: 0

Nexthop count : 0

SpfLink count : 2

-->0000.0000.0001.00

LinkCost : 0

LinkNewCost : 0

LinkFlag : -/-/-/P/-/-/-/-/-

LinkSrcCnt : 1

Type: Remote Interface: N/A

Cost: 0 Nexthop : N/A

-->0000.0000.0004.00

LinkCost : 0

LinkNewCost : 0

LinkFlag : -/-/C/-/-/-/-/-/-

LinkSrcCnt : 1

Type: Remote Interface: Vlan50

Cost: 0 Nexthop : 1.1.1.3

# Display detailed information about the SPF node with system ID 0000.0000.0002.00

<Sysname>display isis spf-tree source-id 0000.0000.0002.00

Shortest Path Tree for IS-IS(1)

-------------------------------

Flags: S-Node is on SPF tree T-Node is on tent list

O-Node is overload R-Node is directly reachable

I-Node or Link is isolated D-Node or Link is to be deleted

C-Neighbor is child P-Neighbor is parent

V-Link is involved N-Link is a new path

L-Link is on change list U-Protocol usage is changed

H-Nexthop is changed

Level-1 Shortest Path Tree

--------------------------

SpfNode : 0000.0000.0002.00

Distance : 10

TE distance : 10

NodeFlag : S/-/-/-/-/-

RelayNibID : 0x0

TE tunnel count: 0

Nexthop count : 1

Neighbor : 0000.0000.0002.00 Interface : Vlan100

Nexthop : 101.1.1.2

BkNeighbor : N/A BkInterface: N/A

BkNexthop : N/A

SpfLink count : 2

-->0000.0000.0002.01

LinkCost : 60

LinkNewCost : 60

LinkFlag : -/-/-/P/-/-/-/-/-

LinkSrcCnt : 1

Type : Remote Interface: N/A

Cost : 60 Nexthop : N/A

AdvMtID : 0

-->0000.0000.0003.01

LinkCost : 10

LinkNewCost : 10

LinkFlag : -/-/C/-/-/-/-/-/-

LinkSrcCnt : 1

Type : Remote Interface: N/A

Cost : 10 Nexthop : N/A

AdvMtID : 0

Level-2 Shortest Path Tree

--------------------------

SpfNode : 0000.0000.0002.00

Distance : 10

TE distance : 10

NodeFlag : S/-/-/-/-/-

RelayNibID : 0x0

TE tunnel count: 0

Nexthop count : 1

Neighbor : 0000.0000.0002.00 Interface : Vlan100

Nexthop : 101.1.1.2

BkNeighbor : N/A BkInterface: N/A

BkNexthop : N/A

SpfLink count : 2

-->0000.0000.0002.01

LinkCost : 60

LinkNewCost : 60

LinkFlag : -/-/-/P/-/-/-/-/-

LinkSrcCnt : 1

Type : Remote Interface: N/A

Cost : 60 Nexthop : N/A

AdvMtID : 0

-->0000.0000.0003.01

LinkCost : 10

LinkNewCost : 10

LinkFlag : -/-/C/-/-/-/-/-/-

LinkSrcCnt : 1

Type : Remote Interface: N/A

Cost : 10 Nexthop : N/A

AdvMtID : 0

Table 27 Command output

Field	Description
SpfNode	ID of the topology node.
Distance	Shortest distance from the root node to the local node.
TE distance	Shortest distance from the root node to the local node (including tunnel links). If tunnel is not configured, TE distance equals to Distance.
NodeFlag	Node flag: · S—The node is on the SPF tree. · T—The node is on the tent list. · O—The node is overloaded. · R—The node is directly connected. · I—The node is isolated. · D—The node is to be deleted.
RelayNibID	Next hop ID of the node after route recursion.
TE tunnel count	Number of tunnels destined to this node.
Destination	Destination router.
TE cost	IGP cost of the TE tunnel.
Final cost	Final cost of the TE tunnel.
Nexthop count	Next hop count.
Nexthop	Primary next hop of the node or the link advertising source.
MADuration	Microloop avoidance delay timer in milliseconds.
MALStack	Microloop avoidance label stack.
AdvMtID	Topology from which the routing information is learned: · 0—Base topology. · 6-4094—Other topologies.
Interface	Primary output interface of the node or the link advertising source.
BkNexthop	Backup next hop.
BkInterface	Backup output interface.
Neighbor	ID of the primary next hop neighbor.
BkNeighbor	ID of the backup next hop neighbor.
TiLfaNeighbor	ID of the TI-LFA backup next hop neighbor.
TiLfaInterface	Output interface of the TI-LFA backup next hop.
TiLfaNexthop	TI-LFA backup next hop.
PNode SrcID	Source ID of the P node.
QNode SrcID	Source ID of the Q node.
PNode prefix	Prefix of the P node. N/A indicates that the prefix of the destination node is not displayed in the P space.
PNode SidIndex	Index value of the prefix SID for the P node. N/A indicates that the prefix SID of the destination node is not displayed in the P space.
Protect	TI-LFA/Remote LFA traffic protection type: · Link—Link protection. · Node—Node protection.
Label stack	Label stack. N/A indicates that no label stack exists.
SpfLink	Topology link.
SpfLink count	Number of topology links.
LinkCost	Link cost.
LinkNewCost	New link cost.
LinkFlag	Link flag: · I—The link is isolated. · D—The link is to be deleted. · C—The neighbor is a child node. · P—The neighbor is the parent node. · V—The link is involved. · N—The link is a new path. · L—The link is on the change list. · U—The protocol usage of the link is changed. · H—The next hop of the link is changed.
LinkSrcCnt	Number of link advertising sources.
Type	Type of the link advertising source: · Adjacent—The link advertising source is a local neighbor. · Remote—The link advertising source is advertised by a remote node in an LSP.
Cost	Cost of the link advertising source.
Remote-LFA	Remote LFA backup information.
RLFANeighbor	System ID of the remote LFA backup next hop.
PQNode	System ID of the PQ node.
PQNodePrefix	PQ node prefix.
OutLabel	Backup label to the PQ node.

# Display brief IPv6 IS-IS SPF tree information.

<Sysname> display isis spf-tree ipv6

Shortest Path Tree for IS-IS(1)

-------------------------------

Flags: S-Node is on SPF tree T-Node is on tent list

O-Node is overload R-Node is directly reachable

I-Node or Link is isolated D-Node or Link is to be deleted

C-Neighbor is child P-Neighbor is parent

V-Link is involved N-Link is a new path

L-Link is on change list U-Protocol usage is changed

H-Nexthop is changed

Level-1 Shortest Path Tree

----------------------------------

SpfNode NodeFlag SpfLink LinkCost LinkFlag

-------------------------------------------------------------------------------

0000.0000.0032.00 S/-/-/-/-/-

-->0000.0000.0032.01 10 -/-/C/-/-/-/-/-/-

-->0000.0000.0064.00 10 -/-/C/-/-/-/-/-/-

0000.0000.0032.01 S/-/-/R/-/-

-->0000.0000.0064.00 0 -/-/C/-/-/-/-/-/-

-->0000.0000.0032.00 0 -/-/-/P/-/-/-/-/-

0000.0000.0064.00 S/-/-/R/-/-

-->0000.0000.0032.00 10 -/-/-/P/-/-/-/-/-

-->0000.0000.0032.01 10 -/-/-/P/-/-/-/-/-

Level-2 Shortest Path Tree

----------------------------------

SpfNode NodeFlag SpfLink LinkCost LinkFlag

-------------------------------------------------------------------------------

0000.0000.0032.00 S/-/-/-/-/-

-->0000.0000.0032.01 10 -/-/C/-/-/-/-/-/-

-->0000.0000.0064.00 10 -/-/C/-/-/-/-/-/-

0000.0000.0032.01 S/-/-/R/-/-

-->0000.0000.0064.00 0 -/-/C/-/-/-/-/-/-

-->0000.0000.0032.00 0 -/-/-/P/-/-/-/-/-

0000.0000.0064.00 S/-/-/R/-/-

-->0000.0000.0032.00 10 -/-/-/P/-/-/-/-/-

-->0000.0000.0032.01 10 -/-/-/P/-/-/-/-/-

# Display detailed Level-1 IPv6 IS-IS SPF tree information.

<Sysname> display isis spf-tree ipv6 level-1 verbose

Shortest Path Tree for IS-IS(1)

-------------------------------

Flags: S-Node is on SPF tree T-Node is on tent list

O-Node is overload R-Node is directly reachable

I-Node or Link is isolated D-Node or Link is to be deleted

C-Neighbor is child P-Neighbor is parent

V-Link is involved N-Link is a new path

L-Link is on change list U-Protocol usage is changed

H-Nexthop is changed

Level-1 Shortest Path Tree

--------------------------

SpfNode : 0000.0000.0032.00

Distance : 0

TE distance : 0

NodeFlag : S/-/-/-/-/-

RelayNibID : 0x0

TE tunnel count: 0

Nexthop count : 0

SpfLink count : 2

-->0000.0000.0032.01

LinkCost : 10

LinkNewCost : 10

LinkFlag : -/-/C/-/-/-/-/-/-

LinkSrcCnt : 1

Type : Adjacent Interface: N/A

Cost : 10 Nexthop : N/A

-->0000.0000.0064.00

LinkCost : 10

LinkNewCost : 10

LinkFlag : -/-/C/-/-/-/-/-/-

LinkSrcCnt : 1

Type : Adjacent Interface: Tun1

Cost : 10 Nexthop : FE80::A0A:A40

SpfNode : 0000.0000.0032.01

Distance : 10

TE distance : 10

NodeFlag : S/-/-/R/-/-

RelayNibID : 0x0

TE tunnel count: 0

Nexthop count : 0

SpfLink count : 2

-->0000.0000.0064.00

LinkCost : 0

LinkNewCost : 0

LinkFlag : -/-/C/-/-/-/-/-/-

LinkSrcCnt : 1

Type : Adjacent Interface: Vlan2

Cost : 10 Nexthop : FE80::200:12FF:FE34:1

-->0000.0000.0032.00

LinkCost : 0

LinkNewCost : 0

LinkFlag : -/-/-/P/-/-/-/-/-

LinkSrcCnt : 1

Type : Adjacent Interface: N/A

Cost : 0 Nexthop : N/A

SpfNode : 0000.0000.0064.00

Distance : 10

TE distance : 10

NodeFlag : S/-/-/R/-/-

RelayNibID : 0x0

TE tunnel count: 0

Nexthop count : 2

Neighbor : 0000.0000.0064.00 Interface : Vlan2

NextHop : FE80::200:12FF:FE34:1

BkNeighbor: N/A BkInterface: N/A

BkNextHop : N/A

Neighbor : 0000.0000.0064.00 Interface : Tun1

NextHop : FE80::A0A:A40

BkNeighbor: N/A BkInterface: N/A

BkNextHop : N/A

SpfLink count : 2

-->0000.0000.0032.00

LinkCost : 10

LinkNewCost : 10

LinkFlag : -/-/-/P/-/-/-/-/-

LinkSrcCnt : 1

Type : Remote Interface: N/A

Cost : 10 Nexthop : N/A

AdvMtID : 0

-->0000.0000.0064.00

LinkCost : 10

LinkNewCost : 10

LinkFlag : -/-/C/-/-/-/-/-/-

LinkSrcCnt : 1

Type : Remote Interface: Tun1

Cost : 10 Nexthop : FE80::A0A:A40

AdvMtID : 0

Table 28 Command output

Field	Description
SpfNode	ID of the topology node.
Distance	Shortest distance from the root node to the current node.
TE distance	Shortest distance from the root node to the current node (including tunnel links). If no tunnels are configured, TE distance equals Distance.
NodeFlag	Node flag: · S—The node is on the SPF tree. · T—The node is on the tent list. · O—The node is overloaded. · R—The node is directly connected. · I—The node is isolated. · D—The node is to be deleted.
TE tunnel count	Number of tunnels destined for this node.
Nexthop count	Number of next hops.
NextHop	Primary next hop of the node or the link advertising source.
AdvMtID	Topology from which the routing information is learned: · 0—Base topology. · 6-4094—Other topologies.
Interface	Primary output interface of the node or the link advertising source.
BkNextHop	Backup next hop.
BkInterface	Backup output interface.
Neighbor	ID of the primary next hop neighbor.
BkNeighbor	ID of the backup next hop neighbor.
SpfLink	Topology link.
SpfLink count	Number of topology links.
LinkCost	Link cost.
LinkNewCost	New link cost.
LinkFlag	Link flag: · I—The link is isolated. · D—The link is to be deleted. · C—The neighbor is a child node. · P—The neighbor is the parent node. · V—The link is involved. · N—The link is a new path. · L—The link is on the change list. · U—The protocol of the link is changed. · H—The next hop of the link is changed.
LinkSrcCnt	Number of link advertising sources.
Type	Type of the link advertising source: · Adjacent—The link advertising source is a local neighbor. · Remote—The link advertising source is advertised by a remote node in an LSP.
Cost	Cost of the link advertising source.

display isis statistics

Use display isis statistics to display IS-IS statistics.

Syntax

display isis statistics [ ipv4 | ipv6 ] [ level-1 | level-1-2 | level-2 ] [ process-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ipv4: Displays IS-IS IPv4 statistics. If you do not specify this option, the command displays IS-IS IPv4 and IPv6 statistics.

ipv6: Displays IS-IS IPv6 statistics.

level-1: Displays IS-IS Level-1 statistics.

level-1-2: Displays IS-IS Level-1-2 statistics.

level-2: Displays IS-IS Level-2 statistics.

process-id: Displays statistics for an IS-IS process specified by its ID in the range of 1 to 65535. If you do not specify an IS-IS process, this command displays the statistics for all IS-IS processes.

Usage guidelines

If you do not specify a level, this command displays both Level-1 and Level-2 routing information.

Examples

# Display IS-IS statistics.

<Sysname> display isis statistics

Statistics information for IS-IS(1)

----------------------------------

Level-1 Statistics

------------------

MTR(base)

Learnt routes information:

Total IPv4 Learnt Routes in IPv4 Routing Table: 1

Imported routes information:

IPv4 Imported Routes:

Static: 0 Direct: 0

ISIS: 0 BGP: 0

RIP: 0 OSPF: 0

EIGRP: 0 UNR: 0

Total Number: 0

MTR(base)

Learnt routes information:

Total IPv6 Learnt Routes in IPv6 Routing Table: 0

Imported routes information:

IPv6 Imported Routes:

Static: 0 Direct: 0

ISISv6: 0 BGP4+: 0

RIPng: 0 OSPFv3: 0

Total Number: 0

Lsp information:

LSP Source ID: No. of used LSPs

7777.8888.1111 001

Level-2 Statistics

------------------

MTR(base)

Learnt routes information:

Total IPv4 Learnt Routes in IPv4 Routing Table: 0

Imported routes information:

IPv4 Imported Routes:

Static: 0 Direct: 0

ISIS: 0 BGP: 0

RIP: 0 OSPF: 0

EIGRP: 0 UNR: 0

Total Number: 0

MTR(base)

Learnt routes information:

Total IPv6 Learnt Routes in IPv6 Routing Table: 0

Imported routes information:

IPv6 Imported Routes:

Static: 0 Direct: 0

ISISv6: 0 BGP4+: 0

RIPng: 0 OSPFv3: 0

UNR: 0

Total Number: 0

Lsp information:

LSP Source ID: No. of used LSPs

7777.8888.1111 001

Table 29 Command output

Field	Description
Statistics information for IS-IS(processid)	Statistics for the IS-IS process.
Level-1 Statistics	Level-1 statistics.
Level-2 Statistics	Level-2 statistics.
MTR(topo-name)	MTR topology. base represents the base topology.
Learnt routes information	· Total IPv4 Learnt Routes in IPv4 Routing Table—Number of learned IPv4 routes. · Total IPv6 Learnt Routes in IPv6 Routing Table—Number of learned IPv6 routes.
IPv4 Imported Routes	Numbers of different types of redistributed IPv4 routes, including static, direct, IS-IS, BGP, RIP, OSPF, EIGRP, and user network routes.
IPv6 Imported Routes	Numbers of different types of redistributed IPv6 routes, including static, direct, IS-ISv6, BGP4+, RIPng, OSPFv3, and user network routes.
Lsp information	LSP information: · LSP Source ID—ID of the source system. · No. of used LSPs—Number of used LSPs.

display osi

Use display osi to display OSI connection information.

Syntax

display osi [ slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies the slot number of the device, which is fixed at 1.

Examples

# Display OSI connection information.

<Sysname> display osi

Total OSI socket number: 2

Location: slot 0

Creator: isisd[1539]

State: N/A

Options: SO_FILTER

Error: 0

Receiving buffer(cc/hiwat/lowat/drop/state): 0 / 1048576 / 1 / 0 / N/A

Sending buffer(cc/hiwat/lowat/state): 0 / 262144 / 512 / N/A

Type: 2

Enabled interfaces:

Vlan-interface100

MAC address: 0180-c200-0014

Location:

Creator: isisd[1539]

State: N/A

Options: SO_FILTER

Error: 0

Receiving buffer(cc/hiwat/lowat/drop/state): 0 / 1048576 / 1 / 0 / N/A

Sending buffer(cc/hiwat/lowat/state): 0 / 262144 / 512 / N/A

Type: 2

Enabled interfaces:

Vlan-interface100

MAC address: 0180-c200-0014

Table 30 Command output

Field	Description
Total OSI socket number	Total number of OSI sockets.
Creator	Name of the socket creator. The process ID of the creator is displayed in the square brackets.
State	This field always displays N/A.
Options	Socket options: · SO_FILTER—Filter option is configured. · N/A—No option is configured.
Error	Number of errors that affect the socket session.
Receiving buffer(cc/hiwat/lowat/drop/state)	Receiving buffer information, including the current used space, maximum space, minimum space, number of dropped packets, and status.
Sending buffer(cc/hiwat/lowat/state)	Sending buffer information, including the current used space, maximum space, minimum space, and status.
Type	Type 2 socket, corresponding to unreliable connectionless-oriented transport layer protocols.
Enabled interfaces	Input interfaces and matched multicast MAC addresses. Only packets received from Ethernet link-layer interfaces need to match the multicast MAC addresses.

display osi statistics

Use display osi statistics to display OSI packet statistics.

Syntax

display osi statistics [ slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies the slot number of the device, which is fixed at 1.

Examples

# Display OSI packet statistics.

<Sysname> display osi statistics

Received packets:

Total: 35

Relay received: 35

Relay forwarded: 35

Invalid service slot: 0

No matched socket: 0

Not delivered, input socket full: 0

Sent packets:

Total: 19

Relay forwarded: 19

Relay received: 19

Failed: 0

Table 31 Command output

Field	Description
Received packets	Statistics of received packets: · Total—Total number of received link layer packets. · Relay received—Number of inbound packets on the cards (where the inbound interfaces reside) relayed from other cards. This count is not included in the total count of received packets. · Relay forwarded—Number of inbound packets relayed to the cards (where the inbound interfaces reside). · Invalid service slot—Number of discarded packets due to unavailable cards (where the inbound interfaces reside). · No matched socket—Number of discarded packets due to mismatches in input interfaces, MAC addresses, or connection filter criteria. · Not delivered, input socket full—Number of undelivered packets due to a socket receiving buffer overflow.
Sent packets	Statistics of sent packets: · Total—Total number of packets that IS-IS sent over OSI connections. · Relay forwarded—Number of outbound packets relayed to the cards that hosts the output interfaces. This count is not included in the total count of sent packets. · Relay received—Number of outbound packets on the cards that hosts the output interfaces. These packets are relayed from other cards. · Failed—Number of packets failed to be sent.

Field

Description

Received packets

Statistics of received packets:

· Total—Total number of received link layer packets.

· Relay received—Number of inbound packets on the cards (where the inbound interfaces reside) relayed from other cards. This count is not included in the total count of received packets.

· Relay forwarded—Number of inbound packets relayed to the cards (where the inbound interfaces reside).

· Invalid service slot—Number of discarded packets due to unavailable cards (where the inbound interfaces reside).

· No matched socket—Number of discarded packets due to mismatches in input interfaces, MAC addresses, or connection filter criteria.

· Not delivered, input socket full—Number of undelivered packets due to a socket receiving buffer overflow.

Sent packets

Statistics of sent packets:

· Total—Total number of packets that IS-IS sent over OSI connections.

· Relay forwarded—Number of outbound packets relayed to the cards that hosts the output interfaces. This count is not included in the total count of sent packets.

· Relay received—Number of outbound packets on the cards that hosts the output interfaces. These packets are relayed from other cards.

· Failed—Number of packets failed to be sent.

Related commands

reset osi statistics

distribute bgp-ls

Use distribute bgp-ls to advertise IS-IS link state information to BGP.

Use undo distribute bgp-ls to restore the default.

Syntax

distribute bgp-ls [ instance-id id ] [ level-1 | level-2 ]

undo distribute bgp-ls [ level-1 | level-2 ]

Default

The device does not advertise IS-IS link state information to BGP.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

instance-id id: Specifies an instance by its ID in the range of 0 to 65535. If you do not specify this option, the command advertises IS-IS link state information of instance 0 to BGP.

level-1: Advertises the Level-1 IS-IS link state information to BGP.

level-2: Advertises the Level-2 IS-IS link state information to BGP.

Usage guidelines

After the device advertises IS-IS link state information to BGP, BGP can advertise the information for intended applications.

If multiple IS-IS processes have the same instance ID and link state information, only the link state information of the IS-IS process with the smallest process ID is advertised.

To advertise the same link state information of different IS-IS processes to BGP, specify a different instance ID for each IS-IS process.

If you do not specify a level for the distribute bgp-ls command, both Level-1 and Level-2 IS-IS link state information can be advertised to BGP.

If you do not specify a level for the undo distribute bgp-ls command, neither Level-1 nor Level-2 IS-IS link state information can be advertised to BGP.

Examples

# Advertise link state information of IS-IS process 1 to BGP.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] distribute bgp-ls

domain-authentication send-only

Use domain-authentication send-only to configure IS-IS not to check the authentication information in the received Level-2 packets, including LSPs, CSNPs, and PSNPs.

Use undo domain-authentication send-only to restore the default.

Syntax

domain-authentication send-only

undo domain-authentication send-only

Default

When domain authentication mode and key are configured, a Level-2 or Level-1-2 device checks the authentication information in the received packets.

Views

IS-IS view

Predefined user roles

network-admin

Usage guidelines

When domain authentication mode and key are configured, a Level-2 or Level-1-2 device adds the key in the specified mode into transmitted Level-2 packets (including LSPs, CSNPs, and PSNPs). It also checks the key in the received Level-2 packets.

To prevent packet exchange failure in case of an authentication key change, configure IS-IS not to check the authentication information in the received packets.

Examples

# Configure IS-IS not to check the authentication information in the received packets.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] domain-authentication send-only

Related commands

area-authentication send-only

domain-authentication-mode

isis authentication send-only

domain-authentication-mode

Use domain-authentication-mode to specify the routing domain authentication mode and a key.

Use undo domain-authentication-mode to restore the default.

Syntax

domain-authentication-mode { { gca key-id { hmac-sha-1 | hmac-sha-224 | hmac-sha-256 | hmac-sha-384 | hmac-sha-512 } [ nonstandard ] | md5 | simple } { cipher | plain } string | keychain keychain-name } [ ip | osi ]

undo domain-authentication-mode

Default

No routing domain authentication mode or key is configured.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

gca: Specifies the GCA mode.

hmac-sha-1: Specifies the HMAC-SHA-1 algorithm.

hmac-sha-224: Specifies the HMAC-SHA-224 algorithm.

hmac-sha-256: Specifies the HMAC-SHA-256 algorithm.

hmac-sha-384: Specifies the HMAC-SHA-384 algorithm.

hmac-sha-512: Specifies the HMAC-SHA-512 algorithm.

nonstandard: Specifies the nonstandard GCA authentication mode.

md5: Specifies the MD5 authentication mode.

simple: Specifies the simple authentication mode.

cipher: Specifies a key in encrypted form.

plain: Specifies a key in plaintext form. For security purposes, the key specified in plaintext form will be stored in encrypted form.

keychain: Specifies the keychain authentication mode.

keychain-name: Specifies a keychain by its name, a case-sensitive string of 1 to 63 characters.

ip: Checks IP-related fields in LSPs.

osi: Checks OSI-related fields in LSPs.

Usage guidelines

The configured key in the specified mode is inserted into all outgoing Level-2 packets (LSP, CSNP, and PSNP) and is used for authenticating the incoming Level-2 packets.

When keychain authentication is used, IS-IS receives and sends packets as follows:

· Before IS-IS sends a Level-2 packet, it uses the valid send key obtained from the keychain to authenticate the packet. If no valid send key exists or the valid send key does not use the HMAC-MD5 or HMAC-SM3 algorithm, the authentication fails and the packet does not contain the authentication information.

· After IS-IS receives a Level-2 packet, it processes the packet as follows:

All the backbone devices must have the same authentication mode and key.

If neither ip nor osi is specified, the OSI-related fields in LSPs are checked.

When you specify the GCA mode, follow these guidelines:

· If you do not specify the nonstandard keyword, the device can communicate only with devices that use the GCA mode.

· If you specify the nonstandard keyword, the device can communicate only with devices that use the nonstandard GCA mode.

In MD5 authentication mode, execute the undo domain-authentication-mode command before version switch if the key lengths supported by the two versions are different.

Examples

# Set the routing domain authentication mode to simple, and set the plaintext key to 123456.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] domain-authentication-mode plain 123456

Related commands

area-authentication-mode

domain-authentication send-only

isis authentication-mode

fast-reroute

Use fast-reroute to configure IS-IS FRR.

Use undo fast-reroute to disable IS-IS FRR.

Syntax

In IS-IS IPv4 unicast address family view:

fast-reroute { lfa [ ecmp-shared | level-1 | level-2 ] | route-policy route-policy-name }

undo fast-reroute { lfa [ ecmp-shared | level-1 | level-2 ] | route-policy }

In IS-IS IPv6 unicast address family view:

fast-reroute { lfa [ level-1 | level-2 ] | route-policy route-policy-name }

undo fast-reroute { lfa [ level-1 | level-2 ] | route-policy }

Default

IS-IS FRR is disabled.

Views

IS-IS IPv4 unicast address family view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

lfa: Calculates a backup next hop through Loop Free Alternate (LFA) calculation.

ecmp-shared: Calculates a backup next hop through LFA calculation for all routes, including ECMP routes. ECMP routes share one backup next hop. If you do not specify this keyword, IS-IS calculates a backup next hop through LFA calculation only for non-ECMP routes. This keyword applies to IPv4 IS-IS and does not take effect when TI-LFA or remote LFA is enabled.

level-1: Specifies Level-1 routes.

level-2: Specifies Level-2 routes.

route-policy route-policy-name: Uses the specified routing policy to designate a backup next hop. The route-policy-name argument is a case-sensitive string of 1 to 63 characters.

Usage guidelines

To calculate a shared backup next hop through LFA calculation for ECMP routes, execute this command with the ecmp-shared keyword. If the next hops of all ECMP routes fail, IS-IS uses the shared backup next hop to forward packets. The shared backup next hop is installed into the RIB as an ECMP route. The state values of the route include Backup in the output from the display ip routing-table command.

The LFA calculation of FRR and IS-IS TE are mutually exclusive.

Example

# Enable FRR for IS-IS process 1 and configure IS-IS FRR to calculate a backup next hop through LFA calculation for all routes.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] fast-reroute lfa

Related commands

display ip routing-table

fast-reroute remote-lfa maximum-cost

Use fast-reroute remote-lfa maximum-cost to set the maximum cost from the source node of a protected link to a PQ node.

Use undo fast-reroute remote-lfa maximum-cost to restore the default.

Syntax

fast-reroute remote-lfa maximum-cost cost [ level-1 | level-2 ]

undo fast-reroute remote-lfa maximum-cost [ level-1 | level-2 ]

Default

The maximum cost from the source node of a protected link to a PQ node is 16777215.

Views

IS-IS IPv4 unicast address family view

Predefined user roles

network-admin

Parameters

cost: Specifies a cost value in the range of 1 to 16777215.

level-1: Applies the configuration to Level-1 areas.

level-2: Applies the configuration to the Level-2 area.

Usage guidelines

The cost values from different PQ nodes to the source node of a specific protected link might be different. You can use this command to filter PQ nodes based on the cost value.

If you specify neither the level-1 nor the level-2 keyword, this command applies to all IS-IS areas.

Examples

# Set the maximum cost from the source node of a protected link to a PQ node to 200.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] fast-reroute remote-lfa maximum-cost 200

fast-reroute remote-lfa prefix-list

Use fast-reroute remote-lfa prefix-list to specify a prefix list to filter remote LFA PQ nodes.

Use undo fast-reroute remote-lfa prefix-list to restore the default.

Syntax

fast-reroute remote-lfa prefix-list prefix-list-name [ level-1 | level-2 ]

undo fast-reroute remote-lfa prefix-list [ level-1 | level-2 ]

Default

Any PQ node can be selected as the backup next hop by remote LFA FRR.

Views

IS-IS IPv4 unicast address family view

Predefined user roles

network-admin

Parameters

prefix-list-name: Specifies a prefix list by its name, a case-sensitive string of 1 to 63 characters.

level-1: Applies the configuration to Level-1 areas.

level-2: Applies the configuration to the Level-2 area.

Usage guidelines

Multiple PQ nodes might reach the source node of a specific protected link. You can use this command to specify a prefix list to filter PQ nodes.

If you specify neither the level-1 nor the level-2 keyword, this command applies to all IS-IS areas.

Examples

# Use prefix list test1 to filter remote LFA PQ nodes.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] fast-reroute remote-lfa prefix-list test1

Related commands

ip prefix-list

fast-reroute remote-lfa tunnel ldp

Use fast-reroute remote-lfa tunnel ldp to enable IS-IS remote LFA FRR.

Use undo fast-refroute remote-lfa tunnel ldp to disable IS-IS remote LFA FRR.

Syntax

fast-reroute remote-lfa tunnel ldp [ level-1 | level-2 ]

undo fast-reroute remote-lfa tunnel ldp [ level-1 | level-2 ]

Default

IS-IS remote LFA FRR is disabled.

Views

IS-IS IPv4 unicast address family view

Predefined user roles

network-admin

Parameters

level-1: Applies the configuration to Level-1 areas.

level-2: Applies the configuration to the Level-2 area.

Usage guidelines

Configure remote LFA FRR to prevent traffic loss caused by link or node failures.

Before configuring remote LFA FRR, you must perform the following tasks:

· Use the mpls ldp command to enable MPLS LDP globally.

· Use the mpls ldp enable command to enable MPLS LDP on all interfaces participating in MPLS forwarding.

· Use the fast-reroute lfa command to enable LFA FRR for the IS-IS level at which remote LFA FRR will be implemented.

If you specify neither the level-1 nor the level-2 keyword, this command applies to all IS-IS areas.

Examples

# Enable remote LFA FRR.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] fast-reroute remote-lfa tunnel ldp

Related commands

fast-reroute

mpls ldp (MPLS Command Reference)

mpls ldp enable (MPLS Command Reference)

fast-reroute tiebreaker

Use fast-reroute tiebreaker to set the priority for the node-protection or lowest-cost backup path selection policy.

Use undo fast-reroute tiebreaker to restore the default.

Syntax

fast-reroute tiebreaker { lowest-cost | node-protecting | srlg-disjoint } preference preference [ level-1 | level-2 ]

undo fast-reroute tiebreaker { lowest-cost | node-protecting | srlg-disjoint } [ level-1 | level-2 ]

Default

The priority values of the node-protection, lowest-cost, and SRLG-disjoint backup path selection policies are 40, 20, and 10, respectively.

Views

IS-IS IPv4 unicast address family view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

lowest-cost: Sets a priority value for the lowest-cost backup path selection policy.

node-protecting: Sets a priority value for the node-protection backup path selection policy.

srlg-disjoint: Sets a priority value for the SRLG-disjoint backup path selection policy.

preference preference: Specifies a priority value in the range of 1 to 255. A higher value indicates a higher priority.

level-1: Applies the configuration to Level-1 areas.

level-2: Applies the configuration to the Level-2 area.

Usage guidelines

If you execute this command multiple times for a backup path selection policy, the most recent configuration takes effect.

If you configure multiple backup path selection policies in an address family view, IS-IS calculates a backup path by using the policies in descending order of their priorities until a backup path is calculated.

If IS-IS fails to calculate a backup path by using the lowest-cost policy, it does not perform further backup path calculation.

If you do not specify a level, the command takes effect on both Level-1 and Level-2 areas.

Examples

# Set the priority value of the node-protection backup path selection policy to 100.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] fast-reroute tiebreaker node-protecting preference 100

Related commands

fast-reroute

filter-policy export

Use filter-policy export to configure IS-IS to filter redistributed routes.

Use undo filter-policy export to remove the configuration.

Syntax

In IS-IS IPv4 unicast address family view:

filter-policy { ipv4-acl-number | prefix-list prefix-list-name | route-policy route-policy-name } export [ bgp | direct | eigrp [ eigrp-as ] | { isis | ospf | rip } [ process-id ] | static | unr ]

undo filter-policy export [ bgp | direct | eigrp [ eigrp-as ] | { isis | ospf | rip } [ process-id ] | static | unr ]

In IS-IS IPv6 unicast address family view:

filter-policy { ipv6-acl-number | prefix-list prefix-list-name | route-policy route-policy-name } export [ bgp4+ | direct | { isisv6 | ospfv3 | ripng } [ process-id ] | static | unr ]

undo filter-policy export [ bgp4+ | direct | { isisv6 | ospfv3 | ripng } [ process-id ] | static | unr ]

Default

IS-IS does not filter redistributed routes.

Views

IS-IS IPv4 unicast address family view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

acl-number: Specifies an ACL by its number in the range of 2000 to 3999 to filter redistributed routes.

prefix-list prefix-list-name: Specifies a prefix list by its name, a case-sensitive string of 1 to 63 characters, to filter redistributed routes by destination address.

route-policy route-policy-name: Specifies a routing policy by its name, a case-sensitive string of 1 to 63 characters, to filter redistributed routes.

bgp: Filters redistributed BGP routes.

bgp4+: Filters redistributed IPv6 BGP routes.

direct: Filters redistributed direct routes.

eigrp: Filters redistributed EIGRP routes.

eigrp-as: Specifies an EIGRP process by its AS number in the range of 1 to 65535. The default value is 1.

isis: Filters redistributed IS-IS routes.

isisv6: Filters redistributed IPv6 IS-IS routes.

ospf: Filters redistributed OSPF routes.

ospfv3: Filters redistributed OSPFv3 routes.

rip: Filters redistributed RIP routes.

ripng: Filters redistributed RIPng routes.

process-id: Specifies a process by its ID in the range of 1 to 65535. The default process ID is 1.

static: Filters redistributed static routes.

unr: Filters redistributed user network routes.

Usage guidelines

If you do not specify any parameters, this command filters all redistributed routes.

This command filters routes redistributed by the import-route command. Only routes that have not been filtered can be advertised.

To use an advanced ACL (with a number from 3000 to 3999) in the command, configure the ACL using one of the following methods:

· To deny/permit a route with the specified destination, use the rule [ rule-id ] { deny | permit } ip source sour-addr sour-wildcard command.

· To deny/permit a route with the specified destination and mask, use the rule [ rule-id ] { deny | permit } ip source sour-addr sour-wildcard destination dest-addr dest-wildcard command.

The source keyword specifies the destination address of a route and the destination keyword specifies the subnet mask of the route. For the configuration to take effect, specify a contiguous subnet mask.

Examples

# Use basic ACL 2000 to filter redistributed routes.

<Sysname> system-view

[Sysname] acl basic 2000

[Sysname-acl-ipv4-basic-2000] rule deny source 192.168.10.0 0.0.0.255

[Sysname-acl-ipv4-basic-2000] quit

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] filter-policy 2000 export

# Configure advanced ACL 3000 to permit only route 113.0.0.0/16 to pass. Use advanced ACL 3000 to filter redistributed routes.

<Sysname> system-view

[Sysname] acl advanced 3000

[Sysname-acl-ipv4-adv-3000] rule 10 permit ip source 113.0.0.0 0 destination 255.255.0.0 0

[Sysname-acl-ipv4-adv-3000] rule 100 deny ip

[Sysname-acl-ipv4-adv-3000] quit

[Sysname] isis 1

[Sysname-isis 1] address-family ipv4

[Sysname-isis-1-ipv4] filter-policy 3000 export

Related commands

display isis route

filter-policy import

Use filter-policy import to configure IS-IS to filter routes calculated using received LSPs.

Use undo filter-policy import to restore the default.

Syntax

filter-policy { acl-number | prefix-list prefix-list-name | route-policy route-policy-name } import

undo filter-policy import

Default

IS-IS does not filter routes calculated using received LSPs.

Views

IS-IS IPv4 unicast address family view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

acl-number: Specifies an ACL by its number in the range of 2000 to 3999 to filter routes calculated using received LSPs.

prefix-list prefix-list-name: Specifies a prefix list by its name, a case-sensitive string of 1 to 63 characters, to filter routes calculated using received LSPs by destination address.

route-policy route-policy-name: Specifies a routing policy by its name, a case-sensitive string of 1 to 63 characters, to filter received routes.

Usage guidelines

This command filters received routes. Only routes that pass the filter can be added into the routing table.

To use an advanced ACL (with a number from 3000 to 3999) in the command, configure the ACL using one of the following methods:

· To deny/permit a route with the specified destination, use the rule [ rule-id ] { deny | permit } ip source sour-addr sour-wildcard command.

· To deny/permit a route with the specified destination and mask, use the rule [ rule-id ] { deny | permit } ip source sour-addr sour-wildcard destination dest-addr dest-wildcard command.

Examples

# Use basic ACL 2000 to filter routes calculated using received LSPs.

<Sysname> system-view

[Sysname] acl basic 2000

[Sysname-acl-ipv4-basic-2000] rule deny source 192.168.10.0 0.0.0.255

[Sysname-acl-ipv4-basic-2000] quit

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] filter-policy 2000 import

# Use advanced ACL 3000 to filter routes calculated using received LSPs and install only route 113.0.0.0/16 to the IP routing table.

<Sysname> system-view

[Sysname] acl advanced 3000

[Sysname-acl-ipv4-adv-3000] rule 10 permit ip source 113.0.0.0 0 destination 255.255.0.0 0

[Sysname-acl-ipv4-adv-3000] rule 100 deny ip

[Sysname-acl-ipv4-adv-3000] quit

[Sysname] isis 1

[Sysname-isis 1] address-family ipv4

[Sysname-isis-1-ipv4] filter-policy 3000 import

Related commands

display ip routing-table

flash-flood

Use flash-flood to enable IS-IS LSP flash flooding.

Use undo flash-flood to disable IS-IS LSP flash flooding.

Syntax

flash-flood [ flood-count flooding-count | max-timer-interval flooding-interval | [ level-1 | level-2 ] ] *

undo flash-flood [ level-1 | level-2 ]

Default

IS-IS LSP flash flooding is disabled.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

flood-count flooding-count: Specifies the maximum number of LSPs to be flooded before the next SPF calculation, in the range of 1 to 15. The default is 5.

max-timer-interval flooding-interval: Specifies the delay of the flash flooding, in the range of 10 to 50000 milliseconds. The default is 10.

level-1: Enables flash flooding for level-1.

level-2: Enables flash flooding for level-2.

Usage guidelines

If no level is specified, the command enables IS-IS LSP flash flooding for both Level-1 and Level-2.

Examples

# Enable fast flooding, and set the maximum LSPs to be sent to 10 and the delay time to 100 milliseconds.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] flash-flood flood-count 10 max-timer-interval 100

graceful-restart

Use graceful-restart to enable IS-IS GR.

Use undo graceful-restart to disable IS-IS GR.

Syntax

graceful-restart

undo graceful-restart

Default

IS-IS GR is disabled.

Views

IS-IS view

Predefined user roles

network-admin

Examples

# Enable GR for IS-IS process 1.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] graceful-restart

Related commands

graceful-restart suppress-sa

Use graceful-restart suppress-sa to suppress the Suppress-Advertisement (SA) bit during restart.

Use undo graceful-restart suppress-sa to restore the default.

Syntax

graceful-restart suppress-sa

undo graceful-restart suppress-sa

Default

The SA bit is set during restart.

Views

IS-IS view

Predefined user roles

network-admin

Usage guidelines

Suppressing the SA bit is mainly for avoiding black hole route. If a device starts or reboots without keeping the local forwarding table, sending packets to the device might result in severe packet loss. To avoid this, you can set the SA bit of the hello packet sent by the GR restarter to 1. Upon receiving such hello packets, the GR helpers will not advertise the GR restarter through LSP.

Examples

# Suppress the SA bit during graceful restart.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] graceful-restart suppress-sa

Related commands

graceful-restart

graceful-restart t1

Use graceful-restart t1 to set the T1 timer.

Use undo graceful-restart t1 to restore the default.

Syntax

graceful-restart t1 seconds count count

undo graceful-restart t1

Default

The T1 timer is 3 seconds and can expire 10 times.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

seconds: Specifies the T1 timer in the range of 3 to 10 seconds.

count: Specifies the number of times that the T1 timer can expire, in the range of 1 to 20.

Usage guidelines

The T1 timer specifies the number of times that GR restarter can send a Restart TLV with the RR bit set. After restart, the GR restarter sends a Restart TLV with the RR bit set to its neighbor. If the restarting device receives a Restart TLV with the RA set from its neighbor before the T1 timer expires, the GR process starts. Otherwise, the GR process fails.

To ensure successful GR timer configuration, follow these restrictions and guidelines when you configure the GR timers:

· The product of the T1 timer and the number of times that the T1 timer can expire must be smaller than the T2 timer.

· The T2 timer must be smaller than the T3 timer.

Examples

# Set the T1 timer of IS-IS process 1 to 5 seconds, and the expiration times to 5.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] graceful-restart t1 5 count 5

Related commands

graceful-restart

graceful-restart t2

graceful-restart t3

graceful-restart t2

Use graceful-restart t2 to set the T2 timer.

Use undo graceful-restart t2 to restore the default.

Syntax

graceful-restart t2 seconds

undo graceful-restart t2

Default

The T2 timer is 60 seconds.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

seconds: Specifies the T2 timer in the range of 30 to 65535 seconds.

Usage guidelines

The T2 timer specifies the LSDB synchronization interval. Each LSDB has a T2 timer. The Level-1-2 device has two T2 timers: a Level-1 timer and a Level-2 timer. If the LSDBs have not achieved synchronization before the two timers expire, the GR process fails.

To ensure successful GR timer configuration, follow these restrictions and guidelines when you configure the GR timers:

· The product of the T1 timer and the number of times that the T1 timer can expire must be smaller than the T2 timer.

· The T2 timer must be smaller than the T3 timer.

Examples

# Set the T2 timer of IS-IS process 1 to 50 seconds.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] graceful-restart t2 50

Related commands

graceful-restart

graceful-restart t1

graceful-restart t3

Use graceful-restart t3 to set the T3 timer.

Use undo graceful-restart t3 to restore the default.

Syntax

graceful-restart t3 seconds

undo graceful-restart t3

Default

The T3 timer is 300 seconds.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

seconds: Specifies the T3 timer in the range of 300 to 65535 seconds.

Usage guidelines

The T3 timer specifies the GR interval. The GR interval is set as the holdtime in hello PDUs. Within the interval, the neighbors maintain their adjacency with the GR restarter. If the GR process has not completed within the holdtime, the neighbors tear down the neighbor relationship and the GR process fails.

To ensure successful GR timer configuration, follow these restrictions and guidelines when you configure the GR timers:

· The product of the T1 timer and the number of times that the T1 timer can expire must be smaller than the T2 timer.

· The T2 timer must be smaller than the T3 timer.

Examples

# Set the T3 timer of IS-IS process 1 to 500 seconds.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] graceful-restart t3 500

Related commands

graceful-restart

graceful-restart t1

graceful-restart t2

ignore-att

Use ignore-att to configure IS-IS not to calculate the default route through the ATT bit.

Use undo ignore-att to restore the default.

Syntax

ignore-att

undo ignore-att

Default

IS-IS calculates the default route through the ATT bit.

Views

IS-IS view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Examples

# Configure IS-IS not to calculate the default route through the ATT bit.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] ignore-att

import-route

Use import-route to enable route redistribution.

Use undo import-route to disable route redistribution.

Syntax

In IS-IS IPv4 unicast address family view:

import-route bgp [ as-number ] [ allow-ibgp ] [ cost cost-value | cost-type { external | internal } | [ level-1 | level-1-2 | level-2 ] | route-policy route-policy-name | tag tag ] *

import-route bgp [ as-number ] [ allow-ibgp ] inherit-cost [ [ level-1 | level-1-2 | level-2 ] | route-policy route-policy-name | tag tag ] *

import-route { direct | static | unr } [ cost cost-value | cost-type { external | internal } | [ level-1 | level-1-2 | level-2 ] | route-policy route-policy-name | tag tag ] *

import-route { direct | static | unr } inherit-cost [ [ level-1 | level-1-2 | level-2 ] | route-policy route-policy-name | tag tag ] *

import-route eigrp [ eigrp-as | all-as ] [ allow-direct | cost cost-value | cost-type { external | internal } | [ level-1 | level-1-2 | level-2 ] | route-policy route-policy-name | tag tag ] *

import-route rip [ process-id | all-processes ] [ allow-direct | cost cost-value | cost-type { external | internal } | [ level-1 | level-1-2 | level-2 ] | route-policy route-policy-name | tag tag ] *

import-route { isis | ospf } [ process-id | all-processes ] [ allow-direct | cost cost-value | cost-type { external | internal } | [ level-1 | level-1-2 | level-2 ] | no-sid | route-policy route-policy-name | tag tag ] *

import-route { isis | ospf } [ process-id | all-processes ] inherit-cost [ allow-direct | [ level-1 | level-1-2 | level-2 ] | no-sid | route-policy route-policy-name | tag tag ] *

undo import-route { bgp | direct | eigrp [ eigrp-as | all-as ] | { isis | ospf | rip } [ process-id | all-processes ] | static | unr }

In IS-IS IPv6 unicast address family view:

import-route { direct | static } [ [ cost cost-value | inherit-cost ] | [ level-1 | level-1-2 | level-2 ] | route-policy route-policy-name | tag tag ] *

import-route { isisv6 | ospfv3 | ripng } [ process-id ] [ allow-direct | [ cost cost-value | inherit-cost ] | [ level-1 | level-1-2 | level-2 ] | route-policy route-policy-name | tag tag ] *

undo import-route { bgp4+ | direct | { isisv6 | ospfv3 | ripng } [ process-id ] | static | unr }

Default

IS-IS does not redistribute routes.

Views

IS-IS IPv4 unicast address family view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

bgp: Redistributes BGP routes.

bgp4+: Redistributes IPv6 BGP routes.

as-number: Specifies an AS by its number in the range of 1 to 4294967295. This argument applies only to the BGP or BGP4+ protocol. If you do not specify this argument, the command redistributes all IPv4 or IPv6 EBGP routes. As a best practice, specify an AS to prevent the system from redistributing excessive routes.

direct: Redistributes direct routes.

eigrp: Redistributes EIGRP routes.

eigrp-as: Specifies an EIGRP process by its number in the range of 1 to 65535. The default value is 1.

all-as: Redistributes routes from all EIGRP processes.

isis: Redistributes IS-IS routes.

isisv6: Redistributes IPv6 IS-IS routes.

ospf: Redistributes OSPF routes.

ospfv3: Redistributes OSPFv3 routes.

rip: Redistributes RIP routes.

ripng: Redistributes RIPng routes.

process-id: Specifies a process by its ID in the range of 1 to 65535. The default value is 1.

static: Redistributes static routes.

unr: Redistributes user network routes. User network routes are generated by access devices for online users.

all-processes: Redistributes routes from all the processes of the IS-IS, OSPF, or RIP routing protocol.

allow-ibgp: Allows redistribution of IBGP routes.

allow-direct: Redistributes the networks of the local interfaces enabled with the specified routing protocol. By default, the networks of the local interfaces are not redistributed. If you specify both the allow-direct keyword and the route-policy route-policy-name option, make sure the if-match rule defined in the routing policy does not conflict with the allow-direct keyword. For example, if you specify the allow-direct keyword, do not configure the if-match route-type rule for the routing policy. Otherwise, the allow-direct keyword does not take effect.

cost cost-value: Specifies a cost for redistributed routes, which is in the range of 0 to 4261412864.

· For the styles of narrow, narrow-compatible, and compatible, the cost is in the range of 0 to 63.

· For the styles of wide and wide-compatible, the cost is in the range of 0 to 4261412864.

cost-type { external | internal }: Specifies the cost type. The internal type indicates internal routes, and the external type indicates external routes. If external is specified, the cost of a redistributed route is added by 64 to make internal routes take priority over external routes. The type is external by default. The keywords are available only when the cost type is narrow, narrow-compatible, or compatible.

inherit-cost: Uses the original cost of redistributed routes.

level-1: Redistributes routes into the Level-1 routing table.

level-1-2: Redistributes routes into both Level-1 and Level-2 routing tables.

level-2: Redistributes routes into the Level-2 routing table. If no level is specified, the routes are redistributed into the Level-2 routing table by default.

no-sid: Redistributes routes without reserving their SR labels. If you do not specify this keyword, ISIS reserves the SR labels of redistributed routes.

route-policy route-policy-name: Redistributes only routes matching the specified routing policy. The route-policy-name argument is a case-sensitive string of 1 to 63 characters.

tag tag: Specifies a tag value for marking redistributed routes, in the range of 1 to 4294967295.

Usage guidelines

IS-IS takes all the redistributed routes as external routes to destinations outside the IS-IS routing domain.

After you specify the cost or inherit-cost keyword, the effective cost varies by cost style. For the styles of narrow, narrow-compatible, and compatible, the cost is in the range of 0 to 63. If the cost is more than 63, 63 is used. For the style of wide or wide-compatible, the configured value is the effective value.

This import-route command cannot redistribute default routes. The command redistributes only active routes. To display route state information, use the display ip routing-table protocol command.

If you specify neither the cost nor inherit-cost keyword, the cost of a redistributed route is 0.

The import-route bgp or import-route bgp4+ command redistributes only EBGP routes. The import-route bgp allow-ibgp or import-route bgp4+ allow-ibgp command redistributes IBGP routes in addition to EBGP routes.

IMPORTANT:

Improper redistribution of IBGP routes might cause routing loops. When you use the allow-ibgp keyword, make sure you understand its impact on the network.

The undo import-route eigrp all-as command can remove the configuration of the import-route eigrp all-as comand only. To remove the configuration of the import-route eigrp eigrp-as command, use the undo form of the command.

The undo import-route protocol all-processes command can remove the configuration of the import-route protocol all-processes comand only. To remove the configuration of the import-route protocol process-id command, use the undo form of the command.

Examples

# Redistribute static routes into IS-IS, and set the cost of redistributed routes to 15.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] import-route static cost 15

Related commands

import-route limit

import-route isis level-1 into level-2

Use import-route isis level-1 into level-2 to enable route advertisement from Level-1 to Level-2.

Use undo import-route isis level-1 into level-2 to disable route advertisement from Level-1 to Level-2.

Syntax

import-route isis level-1 into level-2 [ filter-policy { ipv4-acl-number | prefix-list prefix-list-name | route-policy route-policy-name } | tag tag ] *

undo import-route isis level-1 into level-2

Default

Route advertisement from Level-1 to Level-2 is enabled.

Views

IS-IS IPv4 unicast address family view

Predefined user roles

network-admin

Parameters

filter-policy: Specifies a filtering policy.

ipv4-acl-number: Specifies an ACL by its number in the range of 2000 to 3999 to filter routes from Level-1 to Level-2.

prefix-list prefix-list-name: Specifies an IPv4 prefix list by its name, a case-sensitive string of 1 to 63 characters, to filter routes from Level-1 to Level-2 by destination address.

route-policy route-policy-name: Specifies a routing policy by its name, a case-sensitive string of 1 to 63 characters, to filter routes from Level-1 to Level-2.

tag tag: Specifies a tag for marking redistributed routes, in the range of 1 to 4294967295.

Usage guidelines

If a routing policy is used, the routing policy must be specified in the import-route isis level-1 into level-2 command to filter routes from Level-1 to Level-2. Other routing policies specified for route reception and redistribution do not affect the route leaking.

If a filtering policy is configured, only Level-1 routes not filtered out can be advertised into the Level-2 area.

Examples

# Enable route advertisement from Level-1 to Level-2.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] import-route isis level-1 into level-2

Related commands

import-route

import-route isis level-1 into level-2

import-route isis level-2 into level-1

Use import-route isis level-2 into level-1 to enable route advertisement from Level-2 to Level-1.

Use undo import-route isis level-2 into level-1 to restore the default.

Syntax

import-route isis level-2 into level-1 [ filter-policy { ipv4-acl-number | prefix-list prefix-list-name | route-policy route-policy-name } | tag tag ] *

undo import-route isis level-2 into level-1

Default

Route advertisement from Level-2 to Level-1 is disabled.

Views

IS-IS IPv4 unicast address family view

Predefined user roles

network-admin

Parameters

filter-policy: Specifies a filtering policy.

ipv4-acl-number: Specifies an ACL by its number in the range of 2000 to 3999 to filter routes from Level-2 to Level-1.

prefix-list prefix-list-name: Specifies an IPv4 prefix list by its name, a case-sensitive string of 1 to 63 characters, to filter routes from Level-2 to Level-1 by destination address.

route-policy route-policy-name: Uses the specified routing policy to filter routes from Level-2 to Level-1. The route-policy-name argument is a case-sensitive string of 1 to 63 characters.

tag tag: Specifies a tag for marking redistributed routes, in the range of 1 to 4294967295.

Usage guidelines

If a routing policy is used, the routing policy must be specified in the import-route isis level-2 into level-1 command to filter routes from Level-2 to Level-1. Other routing policies specified for route reception and redistribution does not affect the route leaking.

If a filtering policy is configured, only Level-2 routes not filtered out can be advertised into the Level-1 area.

Examples

# Enable route advertisement from Level-2 to Level-1.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] import-route isis level-2 into level-1

Related commands

import-route

import-route isis level-1 into level-2

import-route isisv6 level-1 into level-2

Use import-route isisv6 level-1 into level-2 to enable route advertisement from Level-1 to Level-2.

Use undo import-route isisv6 level-1 into level-2 to disable route advertisement from Level-1 to Level-2.

Syntax

import-route isisv6 level-1 into level-2 [ filter-policy { ipv6-acl-number | prefix-list prefix-list-name | route-policy route-policy-name } | tag tag ] *

undo import-route isisv6 level-1 into level-2

Default

Route advertisement from Level-1 to Level-2 is enabled.

Views

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

filter-policy: Specifies a filtering policy.

ipv6-acl-number: Specifies an IPv6 ACL by its number in the range of 2000 to 3999.

prefix-list prefix-list-name: Specifies an IPv6 prefix list by its name, a case-sensitive string of 1 to 63 characters.

route-policy route-policy-name: Specifies a routing policy by its name, a case-sensitive string of 1 to 63 characters.

tag tag: Specifies an administrative tag for marking redistributed routes, in the range of 1 to 4294967295.

Usage guidelines

This command enables a Level-1-2 device to redistribute Level-1 routes to Level-2 devices and Level-1-2 devices in the local area.

Examples

# Enable route advertisement from Level-1 to Level-2.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv6

[Sysname-isis-1-ipv6] import-route isisv6 level-1 into level-2

import-route isisv6 level-2 into level-1

Use import-route isisv6 level-2 into level-1 to enable IPv6 IS-IS route advertisement from Level-2 to Level-1.

Use undo import-route isisv6 level-2 into level-1 to restore the default.

Syntax

import-route isisv6 level-2 into level-1 [ filter-policy { ipv6-acl-number | prefix-list prefix-list-name | route-policy route-policy-name } | tag tag ] *

undo import-route isisv6 level-2 into level-1

Default

IPv6 IS-IS route advertisement from Level-2 to Level-1 is disabled.

Views

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

filter-policy: Specifies a filtering policy.

ipv6-acl-number: Specifies an IPv6 ACL by its number in the range of 2000 to 3999.

prefix-list prefix-list-name: Specifies an IPv6 prefix list by its name, a case-sensitive string of 1 to 63 characters.

route-policy route-policy-name: Specifies a routing policy by its name, a case-sensitive string of 1 to 63 characters.

tag tag: Specifies an administrative tag for marking redistributed routes, in the range of 1 to 4294967295.

Usage guidelines

This command enables a Level-1-2 device to redistribute Level-2 routes to the Level-1 and Level-1-2 devices in the local area.

Examples

# Enable IPv6 IS-IS route advertisement from Level-2 to Level-1.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv6

[Sysname-isis-1-ipv6] import-route isisv6 level-2 into level-1

import-route limit

Use import-route limit to configure the maximum number of redistributed Level 1/Level 2 routes.

Use undo import-route limit to restore the default.

Syntax

import-route limit number

undo import-route limit

Default

The maximum number of redistributed Level 1/Level 2 IPv4 routes is 1030144, and the maximum number of redistributed Level 1/Level 2 IPv6 routes is 65536.

Views

IS-IS IPv4 unicast address family view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

number: Specifies the maximum number of redistributed Level 1/Level 2 routes. The value range for this argument is 1 to 1030144 for IPv4 IS-IS and 1 to 65536 for IPv6 IS-IS.

Examples

# Configure IS-IS process 1 to redistribute up to 1000 Level 1/Level 2 IPv4 routes.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] import-route limit 1000

Related commands

import-route

isis

Use isis to enable IS-IS and enter IS-IS view.

Use undo isis to disable IS-IS.

Syntax

isis [ process-id ] [ vpn-instance vpn-instance-name ]

undo isis [ process-id ]

Default

IS-IS is disabled.

Views

System view

Predefined user roles

network-admin

Parameters

process-id: Specifies an IS-IS process by its ID in the range of 1 to 65535. The default is 1.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If no VPN instance is specified, the IS-IS process runs on the public network.

Examples

# Enable IS-IS process 1 and set the system ID to 0000.0000.0002 and area ID to 01.0001.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] network-entity 01.0001.0000.0000.0002.00

Related commands

isis enable

network-entity

isis authentication send-only

Use isis authentication send-only to configure an IS-IS interface not to check the authentication information in the received hello packets.

Use undo isis authentication send-only to remove the configuration.

Syntax

isis authentication send-only [ level-1 | level-2 ]

undo isis authentication send-only [ level-1 | level-2 ]

Default

When interface authentication mode and key are configured, an IS-IS interface checks the authentication information in the received packets.

Views

Interface view

Predefined user roles

network-admin

Parameters

level-1: Configures IS-IS not to check the authentication information in the received Level-1 hello packets.

level-2: Configures IS-IS not to check the authentication information in the received Level-2 hello packets.

Usage guidelines

When peer authentication mode and key are configured, an IS-IS interface adds the key in the specified mode into transmitted hello packets. It also checks the key in the received hello packets.

To prevent packet exchange failure in case of an authentication key change, configure the IS-IS interface not to check the authentication information in the received packets.

Examples

# Configure VLAN-interface 10 not to check the authentication information in the received Level-1 hello packets.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis authentication send-only level-1

Related commands

area-authentication send-only

domain-authentication send-only

isis authentication-mode

Use isis authentication-mode to specify the neighbor relationship authentication mode and a key.

Use undo isis authentication-mode to remove the configuration.

Syntax

isis [ process-id process-id ] authentication-mode { { gca key-id { hmac-sha-1 | hmac-sha-224 | hmac-sha-256 | hmac-sha-384 | hmac-sha-512 } [ nonstandard ] | md5 | simple } { cipher | plain } string | keychain keychain-name } [ level-1 | level-2 ] [ ip | osi ]

undo isis [ process-id process-id ] authentication-mode [ level-1 | level-2 ]

Default

No neighbor relationship authentication mode or key is configured.

Views

Interface view

Predefined user roles

network-admin

Parameters

process-id process-id: Specifies an IS-IS multi-instance process by its ID in the range of 1 to 65535. If you do not specify this option, the traditional IS-IS process is specified.

gca: Specifies the GCA mode.

hmac-sha-1: Specifies the HMAC-SHA-1 algorithm.

hmac-sha-224: Specifies the HMAC-SHA-224 algorithm.

hmac-sha-256: Specifies the HMAC-SHA-256 algorithm.

hmac-sha-384: Specifies the HMAC-SHA-384 algorithm.

hmac-sha-512: Specifies the HMAC-SHA-512 algorithm.

nonstandard: Specifies the nonstandard GCA mode.

md5: Specifies the MD5 authentication mode.

simple: Specifies the simple authentication mode.

cipher: Specifies a key in encrypted form.

plain: Specifies a key in plaintext form. For security purposes, the key specified in plaintext form will be stored in encrypted form.

keychain: Specifies the keychain authentication mode.

keychain-name: Specifies a keychain by its name, a case-sensitive string of 1 to 63 characters.

level-1: Configures the key for Level-1.

level-2: Configures the key for Level-2.

ip: Checks IP-related fields in LSPs and SNPs.

osi: Checks OSI-related fields in LSPs and SNPs.

Usage guidelines

The key in the specified mode is inserted into all outbound hello packets and is used for authenticating inbound hello packets. Only if the authentication succeeds can the neighbor relationship be formed.

When keychain authentication is used, IS-IS receives and sends packets as follows:

· Before IS-IS sends a Hello packet, it uses the valid send key obtained from the keychain to authenticate the packet. If no valid send key exists or the valid send key does not use the HMAC-MD5 or HMAC-SM3 algorithm, the authentication fails and the packet does not contain the authentication information.

· After IS-IS receives a Hello packet, it processes the packet as follows:

The level-1 and level-2 keywords are configurable on an interface that has had IS-IS enabled with the isis enable command.

If you configure a key without specifying a level, the key applies to both Level-1 and Level-2.

For two devices to become neighbors, the authentication mode and key at both ends must be identical.

If neither ip nor osi is specified, the OSI-related fields in LSPs are checked.

When you specify the GCA mode, follow these guidelines:

· If you do not specify the nonstandard keyword, the device can communicate only with devices that use the GCA mode.

· If you specify the nonstandard keyword, the device can communicate only with devices that use the nonstandard GCA mode.

In MD5 authentication mode, execute the undo isis authentication-mode command before version switch if the key lengths supported by the two versions are different.

Examples

# On VLAN-interface 10, set the authentication mode to simple, and set the plaintext key to 123456.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis authentication-mode simple plain 123456

Related commands

area-authentication-mode

domain authentication-mode

isis authentication send-only

isis bfd adjust-cost

Use isis bfd adjust-cost to enable IS-IS to adjust the interface cost according to the BFD session state.

Use undo isis bfd adjust-cost to restore the default.

Syntax

isis bfd adjust-cost { cost-offset | max }

undo isis bfd adjust-cost

Default

IS-IS does not adjust the link cost according to the BFD session state.

Views

Interface view

Predefined user roles

network-admin

Parameters

cost-offset: Specifies the value to be added to the interface cost when the BFD session goes down. The value range for this argument is 1 to 16777213. When the BFD session goes down, the interface cost is cost-offset plus the original interface cost, and cannot exceed 16777214.

max: Sets the interface cost to the maximum value 16777214 when the BFD session goes down.

Usage guidelines

After you enable BFD for IS-IS, the IS-IS neighbor relationship goes down when the BFD session is down and comes up when the BFD session is up. When the BFD session state changes frequently, IS-IS neighbor relationship flapping will occur and traffic forwarding might be affected.

To resolve this issue, enable IS-IS to adjust the interface cost according to the BFD session state.

After you execute this command on an interface, IS-IS adjusts the interface cost as follows:

· When the BFD session on the interface goes down, IS-IS increases the cost value for the interface.

· When the BFD session on the interface comes up, IS-IS restores the cost value for the interface.

Examples

# Enable IS-IS to adjust the cost of interface VLAN-interface 11 according to the BFD session state, and set the value to be added to the interface cost to 100.

<Sysname> system-view

[Sysname] interface vlan-interface 11

[Sysname-Vlan-interface11] isis enable 1

[Sysname-Vlan-interface11] isis bfd enable

[Sysname-Vlan-interface11] isis bfd adjust-cost 100

Related commands

display isis interface

isis bfd enable

Use isis bfd enable to enable BFD.

Use undo isis bfd enable to disable BFD.

Syntax

isis bfd enable

undo isis bfd enable

Default

IS-IS BFD is disabled.

Views

Interface view

Predefined user roles

network-admin

Examples

# Enable BFD for IS-IS on VLAN-interface 11.

<Sysname> system-view

[Sysname] interface vlan-interface 11

[Sysname-Vlan-interface11] isis enable

[Sysname-Vlan-interface11] isis bfd enable

isis bfd session-restrict-adj

Use isis bfd session-restrict-adj to enable IPv4 adjacency establishment and maintenance control based on BFD session state.

Use undo isis bfd session-restrict-adj to disable IPv4 adjacency establishment and maintenance control based on BFD session state.

Syntax

isis bfd session-restrict-adj

undo isis bfd session-restrict-adj

Default

IPv4 adjacency establishment and maintenance control based on BFD session state is disabled.

Views

Interface view

Predefined user roles

network-admin

Usage guidelines

When BFD detects a Layer 3 forwarding failure between two devices, the BFD session goes down, which causes the IPv4 IS-IS adjacency to go down. If Layer 2 forwarding is still available, the devices can exchange IS-IS packets and re-establish the adjacency, which might cause traffic loss.

To avoid the issue, execute this command on the BFD-enabled interfaces of the local and remote devices, enabling the interfaces to carry BFD-enabled TLVs in hello packets. After the BFD session goes down, the devices do not establish an adjacency if the exchanged BFD-enabled TLVs are identical.

If you configure this command for an existing adjacency, the BFD session state does not affect the adjacency relationship within the hold time. This mechanism avoids adjacency flaps during the BFD session establishment.

Before configuring this command, enable IPv4 IS-IS BFD by using the isis bfd enable command.

Examples

# Enable IPv4 adjacency establishment and maintenance control based on BFD session state on interface VLAN-interface 11.

<Sysname> system-view

[Sysname] interface vlan-interface 11

[Sysname-Vlan-interface11] isis enable

[Sysname-Vlan-interface11] isis bfd enable

[Sysname-Vlan-interface11] isis bfd session-restrict-adj

Related commands

isis bfd enable

isis circuit-level

Use isis circuit-level to set the circuit level for the interface.

Use undo isis circuit-level to restore the default.

Syntax

isis circuit-level [ level-1 | level-1-2 | level-2 ]

undo isis circuit-level

Default

An interface can establish either the Level-1 or Level-2 adjacency.

Views

Interface view

Predefined user roles

network-admin

Parameters

level-1: Sets the circuit level to Level-1.

level-1-2: Sets the circuit level to Level-1-2.

level-2: Sets the circuit level to Level-2.

Usage guidelines

For a Level-1 (Level-2) device, the circuit level can only be Level-1 (Level-2). For a Level-1-2 device, you must specify a circuit level for a specific interface to form only the specified level neighbor relationship.

Examples

# VLAN-interface 10 is connected to a non-backbone device in the same area. Set the circuit level of VLAN-interface 10 to Level-1 to prevent sending and receiving Level-2 Hello packets.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis enable

[Sysname-Vlan-interface10] isis circuit-level level-1

Related commands

is-level

isis circuit-type p2p

Use isis circuit-type p2p to set the network type of an interface to P2P.

Use undo isis circuit-type to restore the default.

Syntax

isis [ process-id process-id ] circuit-type p2p

undo isis [ process-id process-id ] circuit-type

Default

The network type of an interface varies by physical media.

Views

Interface view

Predefined user roles

network-admin

Parameters

process-id process-id: Specifies an IS-IS multi-instance process by its ID in the range of 1 to 65535. If you do not specify this option, the traditional IS-IS process is specified.

Usage guidelines

Use this command only on a broadcast network with two attached devices.

Interfaces with different network types operate differently. For example, broadcast interfaces must elect a DIS and flood CSNP packets to synchronize the LSDBs. P2P interfaces do not need to elect a DIS, and use a different LSDB synchronization mechanism.

If only two devices exist on a broadcast network, set the network type of attached interfaces to P2P to avoid DIS election and CSNP flooding. This saves network bandwidth and speeds up network convergence.

Examples

# Set the network type of VLAN-interface 10 to P2P.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis enable

[Sysname-Vlan-interface10] isis circuit-type p2p

isis cost

Use isis cost to set the IS-IS cost for an interface.

Use undo isis cost to remove the configuration.

Syntax

isis [ process-id process-id ] cost cost-value [ level-1 | level-2 ]

undo isis [ process-id process-id ] cost [ level-1 | level-2 ]

Default

No IS-IS cost is configured for an interface.

Views

Interface view

Predefined user roles

network-admin

Parameters

process-id process-id: Specifies an IS-IS multi-instance process by its ID in the range of 1 to 65535. If you do not specify this option, the traditional IS-IS process is specified.

cost-value: Specifies an IS-IS cost in the range of 1 to 16777215.

level-1: Applies the cost to Level-1.

level-2: Applies the cost to Level-2.

Usage guidelines

If neither level-1 nor level-2 is included, the cost applies to both level-1 and level-2.

Examples

# Set the Level-2 IS-IS cost to 5 for VLAN-interface 10.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis cost 5 level-2

Related commands

auto-cost enable

bandwidth-reference

isis cost-fallback

Use isis cost-fallback to change the link cost of a Layer 3 aggregate interface when its bandwidth falls below the threshold.

Use undo isis cost-fallback to remove the configuration.

Syntax

isis cost-fallback cost-value threshold bandwidth-value [ level-1 | level-2 ]

undo isis cost-fallback [ level-1 | level-2 ]

Default

A Layer 3 aggregate interface uses the original link cost.

Views

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

cost-value: Specifies a link cost in the range of 1 to 16777215. As a best practice, set the link cost to a value higher than the original link cost of the interface.

threshold bandwidth-value: Specifies the bandwidth threshold in the range of 1 to 2147483648 Mbps.

level-1: Applies the configuration to Level-1 IS-IS.

level-2: Applies the configuration to Level-2 IS-IS.

Usage guidelines

When a member port of a Layer 3 aggregate interface goes down, the bandwidth of the aggregate interface decreases and services might be interrupted. To resolve this issue, execute this command to change the link cost of a Layer 3 aggregate interface as follows:

· When the bandwidth of the Layer 3 aggregate interface falls below the bandwidth threshold, the aggregate interface uses the specified link cost. Then, IS-IS can select an optimal path for traffic forwarding.

· When the bandwidth of the Layer 3 aggregate interface is equal to or larger than the bandwidth threshold, the aggregate interface uses the original link cost.

If you do not specify a level, this command applies to both Level-1 and Level-2 IS-IS.

Examples

# Change the link cost of interface Route-Aggregation 1 to 100 when its bandwidth falls below 300 Mbps.

<Sysname> system-view

[Sysname] interface Route-Aggregation 1

[Sysname-Route-Aggregation1] isis cost-fallback 100 threshold 300

Related commands

display isis interface

isis dis-name

Use isis dis-name to configure a name for a DIS to represent the pseudo node on a broadcast network.

Use undo isis dis-name to restore the default.

Syntax

isis dis-name symbolic-name

undo isis dis-name

Default

No name is configured for the DIS.

Views

Interface view

Predefined user roles

network-admin

Parameters

symbolic-name: Specifies a DIS name, a case-insensitive string of 1 to 64 characters.

Usage guidelines

This command takes effect only on devices that have dynamic system ID to host name mapping enabled. This command does not take effect on Point-to-Point interfaces.

Examples

# Set the DIS name to LOCALAREA.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis dis-name LOCALAREA

Related commands

display isis name-table

is-name

isis dis-priority

Use isis dis-priority to specify a DIS priority at a specified level for an interface.

Use undo isis dis-priority to remove the configuration.

Syntax

isis dis-priority priority [ level-1 | level-2 ]

undo isis dis-priority [ level-1 | level-2 ]

Default

The priority of Level-1 and Level-2 is 64.

Views

Interface view

Predefined user roles

network-admin

Parameters

priority: Specifies a DIS priority in the range of 0 to 127.

level-1: Applies the DIS priority to Level-1.

level-2: Applies the DIS priority to Level-2.

Usage guidelines

On an IS-IS broadcast network, a device must be elected as the DIS at each routing level. Specify a DIS priority at a level for an interface. The greater the interface's priority is, the more likelihood it becomes the DIS. If multiple devices in the broadcast network have the same highest DIS priority, the device with the highest Subnetwork Point of Attachment (SNPA) address becomes the DIS. SNPA addresses are MAC addresses on a broadcast network.

IS-IS has no backup DIS. The device with a priority of 0 can also participate in DIS election.

If neither level-1 nor level-2 is specified, the DIS priority applies to both Level-1 and Level-2.

Examples

# Set the Level-2 DIS priority to 127 for VLAN-interface 10.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis dis-priority 127 level-2

isis enable

Use isis enable to enable an IS-IS process on an interface.

Use undo isis enable to disable IS-IS.

Syntax

isis enable [ process-id ]

undo isis enable

Default

No IS-IS process is enabled on an interface.

Views

Interface view

Predefined user roles

network-admin

Parameters

process-id: Specifies an IS-IS process by its ID in the range of 1 to 65535. The default is 1.

Examples

# Enable IS-IS process 1 globally and enable it on VLAN-interface 10.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] network-entity 10.0001.1010.1020.1030.00

[Sysname-isis-1] quit

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis enable 1

Related commands

isis

network-entity

isis fast-reroute lfa-backup exclude

Use isis fast-reroute lfa-backup exclude to disable LFA calculation on an interface.

Use undo isis fast-reroute lfa-backup exclude to restore the default.

Syntax

isis fast-reroute lfa-backup exclude [ level-1 | level-2 ]

undo isis fast-reroute lfa-backup exclude [ level-1 | level-2 ]

Default

LFA calculation is enabled on an interface, and the interface can be elected as a backup interface.

Views

Interface view

Predefined user roles

network-admin

Parameters

level-1: Disables LFA calculation on the interface whose circuit level is Level-1.

level-2: Disables LFA calculation on the interface whose circuit level is Level-2.

Usage guidelines

When this command is configured, the interface does not participate in the LFA calculation, and cannot be elected as a backup interface.

If you do not specify the level-1 or level-2 keyword, LFA calculation is disabled on the interface regardless of its circuit level.

Examples

# Disable LFA calculation on VLAN-interface 10.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] network-entity 10.0001.1010.1020.1030.00

[Sysname-isis-1] quit

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis enable 1

[Sysname-Vlan-interface10] isis fast-reroute lfa-backup exclude

Related commands

fast-reroute

isis fast-reroute remote-lfa disable

Use isis fast-reroute remote-lfa disable to disable remote LFA calculation on an interface.

Use undo isis fast-reroute remote-lfa disable to enable remote LFA calculation on an interface.

Syntax

isis fast-reroute remote-lfa disable [ level-1 | level-2 ]

undo isis fast-reroute remote-lfa disable [ level-1 | level-2 ]

Default

Remote LFA calculation is enabled on an interface.

Views

Interface view

Predefined user roles

network-admin

Parameters

level-1: Applies the configuration to Level-1 areas.

level-2: Applies the configuration to the Level-2 area.

Usage guidelines

Use this command to disable remote LFA calculation on the interface to prevent it from participating in the calculation.

If you specify neither the level-1 nor the level-2 keyword, this command applies to all IS-IS areas.

Examples

# Disable remote LFA calculation on interface VLAN-interface 10.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis enable 1

[Sysname-Vlan-interface10] isis fast-reroute remote-lfa disable

isis ipv6 bfd adjust-cost

Use isis ipv6 bfd adjust-cost to enable IPv6 IS-IS to adjust the interface cost according to the BFD session state.

Use undo isis ipv6 bfd adjust-cost to restore the default.

Syntax

isis ipv6 bfd adjust-cost { cost-offset | max }

undo isis ipv6 bfd adjust-cost

Default

IPv6 IS-IS does not adjust the interface cost according to the BFD session state.

Views

Interface view

Predefined user roles

network-admin

Parameters

max: Sets the interface cost to the maximum value 16777214 when the BFD session goes down.

Usage guidelines

After you enable BFD for IPv6 IS-IS, the IPv6 IS-IS neighbor relationship goes down when the BFD session is down and comes up when the BFD session is up. When the BFD session state changes frequently, IPv6 IS-IS neighbor relationship flapping will occur and traffic forwarding might be affected.

To resolve this issue, enable IPv6 IS-IS to adjust the interface cost according to the BFD session state.

After you execute this command on an interface, IPv6 IS-IS adjusts the interface cost as follows:

· When the BFD session on the interface goes down, IPv6 IS-IS increases the cost value for the interface.

· When the BFD session on the interface comes up, IPv6 IS-IS restores the cost value for the interface.

Examples

# Enable IPv6 IS-IS to adjust the cost of interface GigabitEthernet 1/0/1 according to the BFD session state, and set the value to be added to the interface cost to 200.

<Sysname> system-view

[Sysname] interface GigabitEthernet1/0/1

[Sysname-GigabitEthernet1/0/1] isis ipv6 enable 1

[Sysname-GigabitEthernet1/0/1] isis ipv6 bfd enable

[Sysname-GigabitEthernet1/0/1] isis ipv6 bfd adjust-cost 200

Related commands

display isis interface

isis ipv6 bfd enable

Use isis ipv6 bfd enable to enable BFD for IPv6 IS-IS.

Use undo isis ipv6 bfd enable to disable BFD for IPv6 IS-IS.

Syntax

isis ipv6 bfd enable

undo isis ipv6 bfd enable

Default

BFD for IPv6 IS-IS is disabled.

Views

Interface view

Predefined user roles

network-admin

Examples

# Enable BFD for IPv6 IS-IS on VLAN-interface 11.

<Sysname> system-view

[Sysname] interface vlan-interface 11

[Sysname-Vlan-interface11] isis ipv6 bfd enable

isis ipv6 bfd session-restrict-adj

Use isis ipv6 bfd session-restrict-adj to enable IPv6 adjacency establishment and maintenance control based on BFD session state.

Use undo isis ipv6 bfd session-restrict-adj to disable IPv6 adjacency establishment and maintenance control based on BFD session state.

Syntax

isis ipv6 bfd session-restrict-adj

undo isis ipv6 bfd session-restrict-adj

Default

IPv6 adjacency establishment and maintenance control based on BFD session state is disabled.

Views

Interface view

Predefined user roles

network-admin

Usage guidelines

When BFD detects a Layer 3 forwarding failure between two devices, the BFD session goes down, which causes the IPv6 IS-IS adjacency to go down. If Layer 2 forwarding is still available, the devices can exchange IS-IS packets and re-establish the adjacency, which might cause traffic loss.

Before configuring this command, enable IPv6 IS-IS BFD by using the isis ipv6 bfd enable command.

Examples

# Enable IPv6 adjacency establishment and maintenance control based on BFD session state on interface VLAN-interface 11.

<Sysname> system-view

[Sysname] interface vlan-interface 11

[Sysname-Vlan-interface11] isis ipv6 enable

[Sysname-Vlan-interface11] isis ipv6 bfd enable

[Sysname-Vlan-interface11] isis ipv6 bfd session-restrict-adj

Related commands

isis ipv6 bfd enable

isis ipv6 cost

Use isis ipv6 cost to set the IPv6 IS-IS cost for an interface.

Use undo isis ipv6 cost to remove the configuration.

Syntax

isis [ process-id process-id ] ipv6 cost cost-value [ level-1 | level-2 ]

undo isis [ process-id process-id ] ipv6 cost [ level-1 | level-2 ]

Default

No IPv6 IS-IS cost is configured for an interface.

Views

Interface view

Predefined user roles

network-admin

Parameters

process-id process-id: Specifies an IS-IS multi-instance process by its ID in the range of 1 to 65535. If you do not specify this option, the traditional IS-IS process is specified.

cost-value: Specifies an IPv6 IS-IS cost in the range of 1 to 16777215.

level-1: Applies the cost to Level-1 routes.

level-2: Applies the cost to Level-2 routes.

Usage guidelines

This command applies to interfaces that are enabled with IPv6 IS-IS.

This command takes effect only when the standard MTR mode is enabled.

Examples

# Set the IPv6 IS-IS cost to 10 for VLAN-interface 11.

<Sysname> system-view

[Sysname] isis 100

[Sysname-isis-100] address-family ipv6 unicast

[Sysname-isis-100-ipv6] quit

[Sysname-isis-100] quit

[Sysname] interface vlan-interface 11

[Sysname-Vlan-interface11] isis ipv6 enable 100

[Sysname-Vlan-interface11] isis ipv6 cost 10

isis ipv6 cost-fallback

Use isis ipv6 cost-fallback to change the IPv6 link cost of a Layer 3 aggregate interface when its bandwidth falls below the threshold.

Use undo isis cost-fallback to remove the configuration.

Syntax

isis ipv6 cost-fallback cost-value threshold bandwidth-value [ level-1 | level-2 ]

undo isis ipv6 cost-fallback [ level-1 | level-2 ]

Default

A Layer 3 aggregate interface uses the original IPv6 link cost.

Views

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

cost-value: Specifies an IPv6 link cost in the range of 1 to 16777215. As a best practice, set the link cost to a value higher than the original IPv6 link cost of the interface.

threshold bandwidth-value: Specifies the bandwidth threshold in the range of 1 to 2147483648 Mbps.

level-1: Applies the configuration to Level-1 IS-IS.

level-2: Applies the configuration to Level-2 IS-IS.

Usage guidelines

When a member port of a Layer 3 aggregate interface goes down, the bandwidth of the aggregate interface decreases and services might be interrupted. To resolve this issue, execute this command to change the IPv6 link cost of a Layer 3 aggregate interface as follows:

· When the bandwidth of the Layer 3 aggregate interface falls below the bandwidth threshold, the aggregate interface uses the specified IPv6 link cost. Then, IS-IS can select an optimal path for traffic forwarding.

· When the bandwidth of the Layer 3 aggregate interface is equal to or larger than the bandwidth threshold, the aggregate interface uses the original IPv6 link cost.

If you do not specify a level, this command applies to both Level-1 and Level-2 IS-IS.

Examples

# Change the IPv6 link cost of interface Route-Aggregation 1 to 100 when its bandwidth falls below 300 Mbps.

<Sysname> system-view

[Sysname] interface Route-Aggregation 1

[Sysname-Route-Aggregation1] isis ipv6 cost-fallback 100 threshold 300

Related commands

display isis interface

isis ipv6 enable

Use isis ipv6 enable to enable IPv6 for IS-IS on an interface.

Use undo isis ipv6 enable to disable IPv6 for IS-IS on an interface.

Syntax

isis ipv6 enable [ process-id ]

undo isis ipv6 enable

Default

IPv6 is disabled for IS-IS on an interface.

Views

Interface view

Predefined user roles

network-admin

Parameters

process-id: Specifies an IS-IS process by its ID in the range of 1 to 65535. The default is 1.

Examples

# Enable IPv6 for IS-IS on VLAN-interface 100.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] network-entity 10.0001.1010.1020.1030.00

[Sysname-isis-1] address-family ipv6 unicast

[Sysname-isis-1-ipv6] quit

[Sysname-isis-1] quit

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] ipv6 address 2002::1/64

[Sysname-Vlan-interface100] isis ipv6 enable 1

isis ipv6 fast-reroute lfa-backup exclude

Use isis ipv6 fast-reroute lfa-backup exclude to disable LFA calculation on an interface.

Use undo isis ipv6 fast-reroute lfa-backup exclude to restore the default.

Syntax

isis ipv6 fast-reroute lfa-backup exclude [ level-1 | level-2 ]

undo isis ipv6 fast-reroute lfa-backup exclude [ level-1 | level-2 ]

Default

LFA calculation is enabled on an interface.

Views

Interface view

Predefined user roles

network-admin

Parameters

level-1: Disables LFA calculation on the interface whose circuit level is Level-1.

level-2: Disables LFA calculation on the interface whose circuit level is Level-2.

Usage guidelines

If you do not specify the level-1 or level-2 keyword, LFA calculation is disabled on the interface regardless of its circuit level.

Examples

# Disable LFA calculation on VLAN-interface 10.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] network-entity 10.0001.1010.1020.1030.00

[Sysname-isis-1] quit

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis ipv6 enable 1

[Sysname-Vlan-interface10] isis ipv6 fast-reroute lfa-backup exclude

Related commands

fast-reroute

isis ipv6 prefix-suppression

Use isis ipv6 prefix-suppression to enable prefix suppression on an interface.

Use undo isis ipv6 prefix-suppression to disable prefix suppression on an interface.

Syntax

isis ipv6 prefix-suppression

undo isis ipv6 prefix-suppression

Default

Prefix suppression is disabled on an interface.

Views

Interface view

Predefined user roles

network-admin

Usage guidelines

By default, IS-IS interfaces advertise their IPv6 prefixes in LSPs. Use this command to disable an interface from advertising its IPv6 prefix in LSPs. This enhances network security by preventing IP routing to the internal nodes and speeds up network convergence.

Examples

# Enable prefix suppression on VLAN-interface 10.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis ipv6 prefix-suppression

isis ipv6 primary-path-detect bfd

Use isis ipv6 primary-path-detect bfd to enable BFD for IPv6 IS-IS.

Use undo isis ipv6 primary-path-detect bfd to disable BFD for IPv6 IS-IS.

Syntax

isis ipv6 primary-path-detect bfd { ctrl | echo }

undo isis ipv6 primary-path-detect bfd

Default

BFD is disabled for IPv6 IS-IS.

Views

Interface view

Predefined user roles

network-admin

Parameters

ctrl: Enables BFD control packet mode.

echo: Enables BFD echo packet mode.

Usage guidelines

This command enables IPv6 IS-IS FRR or IPv6 IS-IS PIC to use BFD to detect primary link failures.

Examples

# Enable BFD control packet mode for IPv6 IS-IS FRR on VLAN-interface 10.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv6

[Sysname-isis-1-ipv6] fast-reroute lfa

[Sysname-isis-1-ipv6] quit

[Sysname-isis-1] quit

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis ipv6 primary-path-detect bfd ctrl

# Enable BFD echo packet mode for IPv6 IS-IS PIC on VLAN-interface 11.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] pic additional-path-always

[Sysname-isis-1] quit

[Sysname] bfd echo-source-ipv6 1::1

[Sysname] interface vlan-interface 11

[Sysname-Vlan-interface11] isis ipv6 primary-path-detect bfd echo

isis ipv6 tag

Use isis ipv6 tag to configure the tag value on an interface.

Use undo isis ipv6 tag to restore the default.

Syntax

isis ipv6 tag tag

undo isis ipv6 tag

Default

No tag value is configured on an interface.

Views

Interface view

Predefined user roles

network-admin

Parameters

tag: Specifies a tag value in the range of 1 to 4294967295.

Usage guidelines

When IS-IS advertises an IPv6 prefix with a tag value, it adds the tag to the IPv6 reachability information TLV, regardless of the link cost style.

Examples

# Set the tag value on VLAN-interface 10.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis ipv6 tag 4294967295

isis link-quality adjust-cost

Use isis link-quality adjust-cost to enable IS-IS to adjust the interface cost according to the link quality.

Use undo isis link-quality adjust-cost to disable IS-IS from adjusting the interface cost according to the link quality.

Syntax

isis link-quality adjust-cost { cost | max }

undo isis link-quality adjust-cost

Default

IS-IS does not adjust the interface cost according to the link quality.

Views

Interface view

Predefined user roles

network-admin

Parameters

cost: Specifies the value to be added to the interface cost when the link quality changes to LOW. The value range for this argument is 1 to 16777213. When the link quality changes to LOW, the interface cost is cost plus the original interface cost. The interface cost cannot exceed the maximum interface cost.

max: Sets the interface cost to the maximum interface cost when the link quality changes to LOW. The maximum interface cost varies by cost type:

· When the cost type is narrow, narrow-compatible, or compatible, the maximum interface cost is 63.

· When the cost type is wide or wide-compatible, the maximum interface cost is 16777215.

Usage guidelines

Error codes, which refer to bit differences between the received and source signals, cannot be avoided because of inevitable link aging and optical path jitter problems. A high error code ratio might cause service degradation or interruption.

To reduce the impact of error codes on an IS-IS network, you can enable IS-IS to adjust the interface cost according to the link quality.

After you configure this command on an interface, IS-IS adjusts the interface cost as follows:

· When the link quality of the interface becomes LOW, OSPF increases the cost value for the interface.

· When the link quality of the interface restores to GOOD, OSPF restores the cost value for the interface.

Examples

# Enable IS-IS to adjust the cost of interface VLAN-interface 10 according to the link quality, and set the value to be added to the interface cost to 200.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis link-quality adjust-cost 200

Related commands

cost-style

isis mesh-group

Use isis mesh-group to add an interface into a mesh group or block the interface.

Use undo isis mesh-group to restore the default.

NOTE:

This command is supported only in R3608 and later.

Syntax

isis mesh-group { mesh-group-number | mesh-blocked }

undo isis mesh-group

Default

An interface does not belong to any mesh group and is not blocked.

Views

Interface view

Predefined user roles

network-admin

Parameters

mesh-group-number: Specifies a mesh group by its number in the range of 1 to 4294967295.

mesh-blocked: Configures the interface to send LSPs only after receiving LSP requests.

Usage guidelines

An interface not in a mesh group floods received LSPs to other interfaces. For an NBMA network with multiple point-to-point links, this mechanism causes repeated LSP flooding and bandwidth waste.

To resolve this issue, use this command to add relevant interfaces to a mesh group. An interface in a mesh group only floods a received LSP to interfaces not in the same mesh group.

You can also use this command to block an interface. A blocked interface sends LSPs only after receiving LSP requests.

The mesh-group feature takes effect only on point-to-point links.

Examples

# Add interface HundredGigE 1/0/1 to mesh group 3.

<Sysname> system-view

[Sysname] interface hundredgige 1/0/1

[Sysname-HundredGigE1/0/1] isis mesh-group 3

isis mib-binding

Use isis mib-binding to bind an IS-IS process to MIB.

Use undo isis mib-binding to restore the default.

Syntax

isis mib-binding process-id

undo isis mib-binding

Default

MIB operation is bound to the IS-IS process with the smallest process ID.

Views

System view

Predefined user roles

network-admin

Parameters

process-id: Specifies an IS-IS process by its ID in the range of 1 to 65535.

Usage guidelines

If the specified the process ID does not exist, the MIB binding configuration fails.

Deleting an IS-IS process bound to MIB operation deletes the MIB binding configuration. MIB operation is bound to the IS-IS process with the smallest process ID.

Examples

# Bind IS-IS process 100 to MIB.

<Sysname> system-view

[Sysname] isis mib-binding 100

isis peer hold-max-cost duration

Use isis peer hold-max-cost duration to enable IS-IS to advertise the maximum link cost to neighbors within the specified period of time.

Use undo isis peer hold-max-cost duration to restore the default.

NOTE:

This command is supported only in R3608 and later.

Syntax

isis peer hold-max-cost duration time

undo isis peer hold-max-cost duration

Default

IS-IS advertises the original link cost to neighbors during a route convergence.

Views

Interface view

Predefined user roles

network-admin

Parameters

time: Specifies the time period during which IS-IS advertises the maximum link cost to neighbors, in the range of 100 to 1000000 milliseconds.

Usage guidelines

On an IS-IS network, when a link recovers from failures or the state of an interface changes, IS-IS will re-establish neighbor relationships and perform route convergence. During the route convergence process, routing loops and traffic loss might occur because the convergence speeds of the nodes are different. To resolve this issue, enable IS-IS to advertise the maximum link cost to neighbors within the specified period of time, so the traffic forwarding path remains unchanged. After the specified period of time, IS-IS advertises the original link cost to neighbors and performs optimal route selection again.

For a P2P neighbor, the timer specified by the time argument starts after the neighbor becomes up. For a broadcast neighbor, the timer specified by the time argument starts after the neighbor becomes up and the DIS is elected.

When the cost type is wide, the maximum link cost is 16777214. When the cost type is Narrow, the maximum link cost is 63.

This command applies to both IPv4 IS-IS and IPv6 IS-IS.

Examples

# On interface VLAN-interface 10, enable IS-IS to advertise the maximum link cost to neighbors within 1000 milliseconds.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis peer hold-max-cost duration 1000

isis peer-ip-check

Use isis peer-ip-check to enable source address check for hello packets on an IS-IS PPP interface. An IS-IS PPP interface can establish a neighbor relationship only with a peer on the same network.

Use undo isis peer-ip-check to restore the default.

Syntax

isis peer-ip-check

undo isis peer-ip-check

Default

An IS-IS PPP interface can have a peer on a different network.

Views

Interface view

Predefined user roles

network-admin

Examples

# Enable source address check for hello packets on Serial 2/1/0.

<Sysname> system-view

[Sysname] interface serial 2/1/0

[Sysname-Serial2/1/0] isis peer-ip-check

isis prefix-suppression

Use isis prefix-suppression to enable prefix suppression on an interface.

Use undo isis prefix-suppression to disable prefix suppression on an interface.

Syntax

isis prefix-suppression

undo isis prefix-suppression

Default

Prefix suppression is disabled on an interface.

Views

Interface view

Predefined user roles

network-admin

Usage guidelines

Use this command to disable an interface from advertising its prefix in LSPs. This enhances network security by preventing IP routing to the interval nodes and speeds up network convergence.

This command is also applicable to the secondary IP address of the interface.

Examples

# Enable prefix suppression on VLAN-interface 10.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis prefix-suppression

isis primary-path-detect bfd

Use isis primary-path-detect bfd to enable BFD for IS-IS FRR or IS-IS PIC.

Use undo isis primary-path-detect bfd to disable BFD for IS-IS FRR or IS-IS PIC.

Syntax

isis primary-path-detect bfd { ctrl | echo }

undo isis primary-path-detect bfd

Default

BFD is disabled for IS-IS FRR or IS-IS PIC.

Views

Interface view

Predefined user roles

network-admin

Parameters

ctrl: Specifies the BFD control packet mode.

echo: Specifies the BFD echo packet mode.

Usage guidelines

This command enables IS-IS FRR or IS-IS PIC to use BFD to detect primary link failures.

Examples

# Enable BFD control packet mode for IS-IS FRR on VLAN-interface 10.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] fast-reroute lfa

[Sysname-isis-1-ipv4] quit

[Sysname-isis-1] quit

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis primary-path-detect bfd ctrl

# Enable BFD echo packet mode for IS-IS PIC on VLAN-interface 11.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] pic additional-path-always

[Sysname-isis-1] quit

[Sysname] bfd echo-source-ip 1.1.1.1

[Sysname] interface vlan-interface 11

[Sysname-Vlan-interface11] isis primary-path-detect bfd echo

isis silent

Use isis silent to disable the interface from sending and receiving IS-IS packets.

Use undo isis silent to restore the default.

Syntax

isis silent

undo isis silent

Default

An interface can send and receive IS-IS packets.

Views

Interface view

Predefined user roles

network-admin

Usage guidelines

This command is not available in loopback interface view.

Examples

# Disable VLAN-interface 10 from sending and receiving IS-IS packets.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis silent

isis small-hello

Use isis small-hello to configure the interface to send small hello packets without CLVs.

Use undo isis small-hello to restore the default.

Syntax

isis small-hello

undo isis small-hello

Default

An interface sends standard hello packets.

Views

Interface view

Predefined user roles

network-admin

Usage guidelines

This command is not available in loopback interface view.

Examples

# Configure VLAN-interface 10 to send small Hello packets.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis small-hello

isis tag

Use isis tag to configure the tag value for an interface.

Use undo isis tag to restore the default.

Syntax

isis tag tag

undo isis tag

Default

The interface is not configured with a tag value.

Views

Interface view

Predefined user roles

network-admin

Parameters

tag: Specifies the tag value in the range of 1 to 4294967295.

Usage guidelines

When IS-IS advertises an IP prefix with a tag value, it adds the tag to the IP reachability information TLV if the link cost style is wide, wide-compatible, or compatible.

Examples

# Configure the tag value for VLAN-interface 10.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis tag 4294967295

isis timer csnp

Use isis timer csnp to set on the DIS of a broadcast network the interval for sending CSNP packets.

Use undo isis timer csnp to remove the configuration.

Syntax

isis timer csnp seconds [ level-1 | level-2 ]

undo isis timer csnp [ level-1 | level-2 ]

Default

The default CSNP interval is 10 seconds.

Views

Interface view

Predefined user roles

network-admin

Parameters

seconds: Specifies on the DIS of a broadcast network the interval for sending CSNP packets. The value range is 1 to 600 seconds.

level-1: Applies the interval to Level-1.

level-2: Applies the interval to Level-2.

Usage guidelines

On a broadcast network, this command only applies to the DIS, because the DIS sends CSNP packets periodically for LSDB synchronization.

If no level is specified, the CSNP interval applies to both Level-1 and Level-2.

Examples

# Configure Level-2 CSNP packets to be sent every 15 seconds over VLAN-interface 10.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis timer csnp 15 level-2

isis timer hello

Use isis timer hello to set the interval for sending hello packets.

Use undo isis timer hello to remove the configuration.

Syntax

isis timer hello seconds [ level-1 | level-2 ]

undo isis timer hello [ level-1 | level-2 ]

Default

The hello interval is 10 seconds.

Views

Interface view

Predefined user roles

network-admin

Parameters

seconds: Specifies the interval for sending hello packets, in the range of 1 to 255 seconds.

level-1: Specifies the interval for sending Level-1 hello packets.

level-2: Specifies the interval for sending Level-2 hello packets.

Usage guidelines

If a neighbor does not receive any hello packets from the device within the advertised hold time, it considers the device down and recalculates the routes. The hold time is the hello multiplier multiplied by the hello interval.

Level-1 and Level-2 hello packets are sent independently on a broadcast network, so you need to specify an interval for each level. On a P2P link, Level-1 and Level-2 packets are both sent in P2P hello packets, and you need not specify an interval for each level.

You can configure the level-1 and level-2 keywords only on broadcast interfaces. Before you configure the level-1 or level-2 keyword, enable IS-IS on the interface.

The shorter the interval, the more system resources will be occupied.

If no level is specified, the hello interval applies to both Level-1 and Level-2.

Examples

# Configure Level-2 hello packets to be sent every 20 seconds over VLAN-interface 10.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis timer hello 20 level-2

Related commands

isis timer holding-multiplier

Use isis timer holding-multiplier to set the IS-IS hello multiplier.

Use undo isis timer holding-multiplier to remove the configuration.

Syntax

isis timer holding-multiplier value [ level-1 | level-2 ]

undo isis timer holding-multiplier [ level-1 | level-2 ]

Default

The default IS-IS hello multiplier is 3.

Views

Interface view

Predefined user roles

network-admin

Parameters

value: Specifies the number of hello intervals, in the range of 3 to 1000.

level-1: Applies the number to the Level-1 IS-IS neighbor.

level-2: Applies the number to the Level-2 IS-IS neighbor.

Usage guidelines

The hello multiplier is the number of hello packets a neighbor must miss before declaring the device is down.

Level-1 and Level-2 hello packets are sent independently on a broadcast network, so you need to specify a hello multiplier for each level. On a P2P link, Level-1 and Level-2 packets are both sent in P2P hello packets, and you need not specify Level-1 or Level-2.

You can configure the level-1 and level-2 keywords only on broadcast interfaces. Before you configure the level-1 or level-2 keyword, enable IS-IS on the interface.

If no level is specified, the hello multiplier applies to both Level-1 and Level-2.

The value of hello multiplier multiplied by hello interval cannot be more than 65535.

Examples

# Set the hello multiplier to 6 for VLAN-interface 10.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis timer holding-multiplier 6

Related commands

isis timer hello

isis timer lsp

Use isis timer lsp to set the minimum interval for sending LSPs on the interface and specify the maximum number of LSPs that can be sent per time.

Use undo isis timer lsp to restore the default.

Syntax

isis timer lsp time [ count count ]

undo isis timer lsp

Default

The minimum interval for sending LSPs on the interface is 33 milliseconds, and the maximum number of LSPs that can be sent at a time is 5.

Views

Interface view

Predefined user roles

network-admin

Parameters

time: Specifies the minimum interval for sending link-state packets, in the range of 1 to 1000 milliseconds.

count: Specifies the maximum number of link-state packets to be sent at one time, in the range of 1 to 1000.

Usage guidelines

If a change occurs in the LSDB, IS-IS advertises the changed LSP to neighbors. You can specify the minimum interval for sending these LSPs to control the amount of LSPs on the network.

Examples

# Set the interval to 500 milliseconds for sending LSPs on VLAN-interface 10.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis timer lsp 500

Related commands

isis timer retransmit

Use isis timer retransmit to configure the interval for retransmitting LSP packets over a point-to-point link.

Use undo isis timer retransmit to restore the default.

Syntax

isis timer retransmit seconds

undo isis timer retransmit

Default

The retransmission interval on a P2P link is 5 seconds.

Views

Interface view

Predefined user roles

network-admin

Parameters

seconds: Specifies the interval for retransmitting LSP packets, in the range of 1 to 300 seconds.

Usage guidelines

On a P2P link, IS-IS requires an advertised LSP be acknowledged. If no acknowledgment is received within a configurable interval, IS-IS will retransmit the LSP.

You do not need to use this command over a broadcast link where CSNPs are periodically broadcast to implement LSDB synchronization.

Examples

# Set the LSP retransmission interval on a P2P link to 50 seconds for VLAN-interface 10.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] isis circuit-type p2p

[Sysname-Vlan-interface10] isis timer retransmit 50

Related commands

isis circuit-type p2p

isis timer lsp

is-level

Use is-level to specify the IS level.

Use undo is-level to restore the default.

Syntax

is-level { level-1 | level-1-2 | level-2 }

undo is-level

Default

The IS level is level-1-2.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

level-1: Specifies Level-1, which means IS-IS only calculates intra-area routes and maintains the Level-1 LSDB.

level-1-2: Specifies Level-1-2, which means IS-IS calculates routes and maintains the LSDBs for both Level-1 and Level-2.

level-2: Specifies Level-2, which means IS-IS calculates routes and maintains the LSDB for Level-2 only.

Usage guidelines

If only one area exists, configure all the devices as either Level-1 or Level-2, because the devices do not need to maintain two identical LSDBs at the same time.

If the only area is an IP network, configure all the devices as Level-2 for scalability.

Examples

# Set the IS level to Level-1 for IS-IS process 1.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] is-level level-1

is-name

Use is-name to specify a host name for the IS and enable dynamic system ID to hostname mapping.

Use undo is-name to disable dynamic system ID to hostname mapping.

Syntax

is-name sys-name

undo is-name

Default

Dynamic system ID to hostname mapping is disabled, and no host name is configured for the IS.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

sys-name: Specifies a host name for the local IS, a case-insensitive string of 1 to 64 characters.

Usage guidelines

To display the host name rather than the system ID of an IS by using the display isis lsdb command, first enable dynamic system ID to hostname mapping.

Examples

# Configure a host name for the local IS.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] is-name RUTA

Related commands

display isis name-table

is-name map

Use is-name map to configure a system ID to host name mapping for a remote IS.

Use undo is-name map to remove the mapping.

Syntax

is-name map sys-id map-sys-name

undo is-name map sys-id

Default

No system ID to host name mapping is configured for a remote IS.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

sys-id: Specifies the system ID or pseudonode ID of a remote IS.

map-sys-name: Specifies a host name for the remote IS, a case-insensitive string of 1 to 64 characters.

Usage guidelines

Each remote IS system ID corresponds to only one name.

Examples

# Map the host name RUTB to the system ID 0000.0000.0041 of the remote IS.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] is-name map 0000.0000.0041 RUTB

Related commands

display isis name-table

ispf enable

Use ispf enable to enable incremental SPF (ISPF).

Use undo ispf enable to disable ISPF.

Syntax

ispf enable

undo ispf enable

Default

ISPF is enabled.

Views

IS-IS view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Usage guidelines

When a network topology is changed, ISPF recomputes only the affected part of the SPT, instead of the entire SPT.

Examples

# Enable IS-IS ISPF.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] ispf enable

log-peer-change

Use log-peer-change to enable the logging of IS-IS neighbor state changes.

Use undo log-peer-change to disable the logging.

Syntax

log-peer-change

undo log-peer-change

Default

The logging of IS-IS neighbor state changes is enabled.

Views

IS-IS view

Predefined user roles

network-admin

Usage guidelines

This command enables sending logs about IS-IS neighbor state changes to the information center. For IS-IS neighbor state change logs to be sent correctly, you must also configure the information center parameters on the device. For more information about information center, see the network management and monitoring configuration guide for the device.

Examples

# Disable the logging of IS-IS neighbor state changes.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] undo log-peer-change

lsp-fragments-extend

Use lsp-fragments–extend to enable LSP fragment extension for a level.

Use undo lsp-fragments–extend to restore the default.

Syntax

lsp-fragments-extend [ level-1 | level-1-2 | level-2 ]

undo lsp-fragments-extend

Default

LSP fragment extension is disabled.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

level-1: Applies the fragment extension to Level-1 LSPs.

level-1-2: Applies the fragment extension to both Level-1 and Level-2 LSPs.

level-2: Applies the fragment extension to Level-2 LSPs.

Usage guidelines

If no level is specified, the command enables LSP fragment extension for both Level-1 and Level-2.

Examples

# Enable LSP fragment extension for Level-2.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] lsp-fragments-extend level-2

lsp-length originate

Use lsp-length originate to configure the maximum size of generated Level-1 or Level-2 LSPs.

Use undo lsp-length originate to remove the configuration.

Syntax

lsp-length originate size [ level-1 | level-2 ]

undo lsp-length originate [ level-1 | level-2 ]

Default

The maximum size of generated Level-1 and Level-2 LSPs is 1497 bytes.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

size: Specifies the maximum size of LSP packets, in the range of 512 to 16384 bytes.

level-1: Applies the size to Level-1 LSP packets.

level-2: Applies the size to Level-2 LSP packets.

Usage guidelines

If neither Level-1 nor Level-2 is specified in the command, the configured maximum size applies to the current IS-IS level.

Examples

# Set the maximum size of the generated Level-2 LSPs to 1024 bytes.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] lsp-length originate 1024 level-2

lsp-length receive

Use lsp-length receive to configure the maximum size of received LSPs.

Use undo lsp-length receive to restore the default.

Syntax

lsp-length receive size

undo lsp-length receive

Default

The maximum size of received LSPs is 1497 bytes.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

size: Specifies the maximum size of received LSPs, in the range of 512 to 16384 bytes.

Examples

# Configure the maximum size of received LSPs to 1024 bytes.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] lsp-length receive 1024

maximum load-balancing

Use maximum load-balancing to configure the maximum number of ECMP routes for load balancing.

Use undo maximum load-balancing to restore the default.

Syntax

maximum load-balancing number

undo maximum load-balancing

Default

The maximum number of IS-IS ECMP routes equals the maximum number of ECMP routes.

Views

IS-IS IPv4 unicast address family view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

number: Specifies the maximum number of ECMP routes. The value of 1 indicates that IS-IS does not perform load balancing.The value range for this argument is 1 to 128.

Examples

# Set the maximum number of ECMP routes to 2.

<Sysname> system-view

[Sysname] isis 100

[Sysname-isis-100] address-family ipv4

[Sysname-isis-100-ipv4] maximum load-balancing 2

multi-instance enable

Use multi-instance enable to enable the IS-IS multi-instance process and specify an instance ID for the process.

Use undo multi-instance enable to disable the IS-IS multi-instance process.

Syntax

multi-instance enable iid iid-value

undo multi-instance enable

Default

IS-IS multi-instance process is disabled.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

iid iid-value: Specifies an instance ID for the IS-IS process, in the range of 1 to 65535.

Usage guidelines

IS-IS processes not enabled with the multi-instance process feature are called traditional IS-IS processes. IS-IS processes enabled with the multi-instance process feature are called IS-IS multi-instance processes.

By default, an interface supports only one IS-IS process. To configure multiple IS-IS processes on a device, you must add more interfaces to the device and configure the interfaces manually. To simplify configuration, use the IS-IS multi-instance process feature to configure multiple IS-IS multi-instance processes as well as a traditional IS-IS process on an interface.

After you enable the IS-IS multi-instance process feature, two devices can establish a neighbor relationship only when you configure the same instance ID for the multi-instance processes on the devices.

When you configure IS-IS multi-instance processes or disable the IS-IS multi-instance process feature, follow these restrictions and guidelines:

· You cannot specify the same instance ID for different IS-IS processes.

· Before enabling or disabling the IS-IS multi-instance process feature on an interface that has been configured with an IS-IS process, disable IS-IS on the interface.

Examples

# Enable IS-IS multi-instance process on IS-IS process 1 and set the instance ID to 3.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] multi-instance enable iid 3

Related commands

isis enable

network-entity

Use network-entity to configure the Network Entity Title (NET) for an IS-IS process.

Use undo network-entity to delete a NET.

Syntax

network-entity net

undo network-entity net

Default

No NET is configured.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

net: Specifies a NET as a dotted hexadecimal string in the X…X.XXXX....XXXX.00 format. The X…X segment represents the area address, the XXXX....XXXX segment represents the system ID, and the 00 segment is the SEL.

Usage guidelines

A NET is a special NSAP address with the SEL being 0. The length of the NET is in the range of 8 to 20 bytes.

A NET comprises the following parts:

· Area ID—With a length of 1 to 13 bytes.

· System ID—A system ID uniquely identifies a host or device in the area and has a fixed 6-byte length.

· SEL—It has a value of 0 and a fixed 1-byte length.

For example, a NET of ab.cdef.1234.5678.9abc.00 specifies the area ID ab.cdef, the system ID 1234.5678.9abc, and the SEL 00.

If you want to execute the cost-style, is-level, and network-entity commands for the same IS-IS process, execute the network-entity command after the other two commands to avoid data loss.

Examples

# Set the NET to 10.0001.1010.1020.1030.00, of which 10.0001 is the area ID and 1010.1020.1030 is the system ID.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] network-entity 10.0001.1010.1020.1030.00

Related commands

cost-style

isis

isis enable

is-level

pic

Use pic to enable IS-IS PIC.

Use undo pic to disable IS-IS PIC.

Syntax

pic [ additional-path-always ]

undo pic

Default

IS-IS PIC is enabled.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

additional-path-always: Allows the indirect suboptimal route as the backup route.

Usage guidelines

Prefix Independent Convergence (PIC) enables the device to speed up network convergence by ignoring the number of prefixes. PIC applies only to indirect routes.

When both IS-IS PIC and IS-IS FRR are configured, only IS-IS FRR takes effect.

Examples

# Configure IS-IS PIC to support the indirect suboptimal route as the backup route.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] pic additional-path-always

preference

Use preference to configure the preference for IS-IS.

Use undo preference to restore the default.

Syntax

preference { preference | route-policy route-policy-name } *

undo preference

Default

IS-IS preference is 15.

Views

IS-IS IPv4 unicast address family view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

preference: Specifies an IS-IS protocol preference in the range of 1 to 255.

route-policy route-policy-name: Specifies a routing policy by its name, a case-sensitive string of 1 to 63 characters, to assign a priority to the matching routes.

Usage guidelines

If multiple routing protocols find routes to the same destination, the route found by the routing protocol with the highest preference is selected as the optimal route.

If a routing policy is specified in this command, the preference set by the routing policy applies to the matching routes. Other routes use the preference set by the preference command.

Examples

# Set the preference for IS-IS to 25.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] preference 25

prefix-priority

Use prefix-priority to assign convergence priorities to specific IS-IS routes.

Use undo prefix-priority to remove the configuration.

Syntax

prefix-priority { critical | high | medium } { prefix-list prefix-list-name | tag tag-value }

prefix-priority route-policy route-policy-name

undo prefix-priority { critical | high | medium } [ prefix-list | tag ]

undo prefix-priority route-policy

Default

IS-IS routes have the lowest convergence priority.

Views

IS-IS IPv4 unicast address family view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

critical: Specifies the highest convergence priority.

high: Specifies the high convergence priority.

medium: Specifies the medium convergence priority.

prefix-list prefix-list-name: Specifies a prefix list by its name, a case-sensitive string of 1 to 63 characters.

tag tag-value: Specifies a tag value in the range of 1 to 4294967295.

route-policy route-policy-name: Specifies a routing policy by its name, a case-sensitive string of 1 to 63 characters.

Usage guidelines

The higher the convergence priority, the faster the convergence speed.

IS-IS host routes have a medium convergence priority.

Examples

# Assign the high convergence priority to IS-IS routes permitted by IP prefix list standtest.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] prefix-priority high prefix-list standtest

reset isis all

Use reset isis all to clear all IS-IS data structure information.

Syntax

reset isis all [ process-id ] [ graceful-restart ]

Views

User view

Predefined user roles

network-admin

Parameters

process-id: Specifies an IS-IS process by its ID in the range of 1 to 65535 to clear the data structure information for an IS-IS process.

graceful-restart: Recovers the data through graceful restart after the data is cleared.

Usage guidelines

If no IS-IS process is specified, the command clears data structure information for all IS-IS processes.

Use this command when LSPs must be updated immediately.

Examples

# Clear all IS-IS data structure information.

<Sysname> reset isis all

reset isis event-log graceful-restart

Use reset isis event-log graceful-restart to clear IS-IS GR log information.

Syntax

reset isis event-log graceful-restart slot slot-number

Views

User view

Predefined user roles

network-admin

Parameters

slot slot-number: Specifies the slot number of the device, which is fixed at 1.

Examples

# Clear IS-IS GR log information for the specified slot.

<Sysname> reset isis event-log graceful-restart slot 1

reset isis event-log lsp

Use reset isis event-log lsp to clear IS-IS LSP log information.

Syntax

reset isis event-log lsp { purged | refreshed } [ process-id ]

Views

User view

Predefined user roles

network-admin

Parameters

purged: Clears log information about purged LSPs.

refreshed: Clears log information about refreshed LSPs.

process-id: Specifies an IS-IS process by its ID in the range of 1 to 65535. If you do not specify this argument, the command clears LSP log information for all IS-IS processes.

Examples

# Clear log information about refreshed LSPs for IS-IS process 1.

<Sysname> reset isis event-log lsp refreshed 1

Related commands

display isis event-log lsp

reset isis event-log spf

Use reset isis event-log spf to clear IS-IS route calculation log information.

Syntax

reset isis event-log spf [ process-id ]

Views

User view

Predefined user roles

network-admin

Parameters

process-id: Specifies an IS-IS process by its ID in the range of 1 to 65535. If you do not specify this argument, the command clears route calculation log information for all IS-IS processes.

Examples

# Clear route calculation log information for IS-IS process 1.

<Sysname> reset isis event-log spf 1

Related commands

display isis event-log spf

reset isis packet

Use reset isis packet to clear IS-IS packet statistics.

Syntax

reset isis packet [ csnp | hello | lsp | psnp ] [ interface-type interface-number ] [ process-id ]

Views

User view

Predefined user roles

network-admin

Parameters

csnp: Clears CSNP packet statistics.

hello: Clears hello packet statistics.

lsp: Clears LSP packet statistics.

psnp: Clears PSNP packet statistics.

interface-type interface-number: Specifies an interface by its type and number. If you do not specify this option, the command clears IS-IS packet statistics for all interfaces.

process-id: Specifies an IS-IS process by its ID in the range of 1 to 65535. If you do not specify this argument, the command clears IS-IS packet statistics for all IS-IS processes.

Examples

# Clear IS-IS packet statistics for all IS-IS processes.

<Sysname> reset isis packet

Related commands

display isis packet

reset isis peer

Use reset isis peer to clear data structure information for a specified IS-IS neighbor.

Syntax

reset isis peer system-id [ process-id ]

Views

User view

Predefined user roles

network-admin

Parameters

system-id: Specifies an IS-IS neighbor by its system ID.

process-id: Specifies an IS-IS process by its ID in the range of 1 to 65535 to clear data structure information for the neighbor in the specified IS-IS process.

Usage guidelines

Use this command when you re-establish an IS-IS neighbor relationship.

Examples

# Clear the data structure information of the neighbor with the system ID 0000.0c11.1111.

<Sysname> reset isis peer 0000.0c11.1111

reset osi statistics

Use reset osi statistics to clear OSI packet statistics.

Syntax

reset osi statistics

Views

User view

Predefined user roles

network-admin

Usage guidelines

To obtain OSI packet statistics from the specified time point, first clear the existing statistics.

Examples

# Clear OSI packet statistics.

<Sysname> reset osi statistics

Related commands

display osi statistics

set-att

Use set-att to set the ATT bit of Level-1 LSPs.

Use undo set-att to restore the default.

Syntax

set-att { always | never }

undo set-att

Default

The Level-1-2 router sets the ATT bit for Level-1 LSPs in accordance with the default ATT bit setting rule.

Views

IS-IS view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

always: Sets the ATT bit of Level-1 LSPs.

never: Keeps the ATT bit of Level-1 LSPs not set.

Usage guidelines

The ATT bit is used to identify the connection status between a Level-1 area and other areas. By default, a Level-1-2 router sets the ATT bit for Level-1 LSPs as follows:

· The Level-1-2 router sets the ATT bit in Level-1 LSPs to inform the Level-1 routers that it can reach other areas. After a Level-1 router receives a Level-1 LSP with the ATT bit set, it generates a default route destined for the Level-1-2 router.

· The Level-1-2 router does not set the ATT bit in Level-1 LSPs if it can reach only one area.

To edit the default ATT bit setting rule for a Level-1-2 router, perform the following tasks as needed:

· To enable ATT bit setting for all Level-1 LSPs, execute the set-att always command on the Level-1-2 router.

· To disable a Level-1 router from generating a default route upon receiving an ATT-bit-set Level-1 LSP from the Level-1-2 router, you can perform one of the following tasks:

¡ Execute the ignore-att command on the Level-1 router.

¡ Execute the set-att never command on the Level-1-2 router.

The set-att command is applicable to only Level-1-2 routers.

Examples

# Set the ATT bit of Level-1 LSPs.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] set-att always

Related commands

ignore-att

set-overload

Use set-overload to set the overload bit.

Use undo set-overload to restore the default.

Syntax

In IS-IS view:

set-overload [ on-startup [ [ start-from-nbr system-id [ timeout1 [ nbr-timeout ] ] ] | timeout2 | wait-for-bgp [ timeout3 ] ] ] [ allow { external | interlevel } * ]

undo set-overload

In IS-IS IPv6 unicast address family view:

set-overload [ on-startup [ [ start-from-nbr system-id [ timeout1 [ nbr-timeout ] ] ] | timeout2 | wait-for-bgp4+ [ timeout3 ] ] ] [ allow { external | interlevel } * ]

undo set-overload

Default

The overload bit is not set.

Views

IS-IS view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

on-startup: Sets the overload bit upon system startup.

start-from-nbr system-id [ timeout1 [ nbr-timeout ] ]: Starts the nbr-timeout timer when the device begins to establish the neighbor relationship with the neighbor after system startup. If the neighbor relationship is formed within the nbr-timeout interval, IS-IS keeps the overload bit set. If not, the bit is cleared. IS-IS keeps the overload bit set within the timeout1 interval after the neighbor relationship is formed within the nbr-timeout interval.

· system-id—Specifies the neighbor.

· timeout1—The timeout1 interval is in the range of 5 to 86400 seconds, and the default is 600 seconds.

· nbr-timeout—The timer has an interval from 5 to 86400 seconds. The default is 1200 seconds.

timeout2: Sets the overload bit within the timeout2 interval after system startup. The interval is in the range of 5 to 86400 seconds, and the default is 600 seconds.

wait-for-bgp [ timeout3 ]: Starts the timeout3 timer for BGP convergence after system startup. If BGP is not converged within the timeout3 interval, IS-IS clears the overload bit. The value range for the timeout3 argument is 5 to 86400 seconds, and the default is 600 seconds.

wait-for-bgp4+ [ timeout3 ]: Starts the timeout3 timer for IPv6 BGP convergence after system startup. If IPv6 BGP is not converged within the timeout3 interval, IPv6 IS-IS clears the overload bit. The value range for the timeout3 argument is 5 to 86400 seconds, and the default is 600 seconds.

allow: Allows advertising address prefixes. By default, no address prefixes are allowed to be advertised when the overload bit is set.

external: Allows advertising IP address prefixes redistributed from other routing protocols with the allow keyword specified.

interlevel: Allows advertising IP address prefixes learned from different IS-IS levels with the allow keyword specified.

Usage guidelines

If the on-startup keyword is not specified, the command sets the overload bit immediately until the undo set-overload command is executed.

If the on-startup keyword is specified, IS-IS sets the overload bit upon system startup and keeps it set within the timeout2 interval.

Examples

# Set overload flag on the current device.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] set-overload

snmp context-name

Use snmp context-name to set the context name for the SNMP object for managing IS-IS.

Use undo snmp context-name to restore the default.

Syntax

snmp context-name context-name

undo snmp context-name

Default

No context name is set for the SNMP object for managing IS-IS.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

context-name: Specifies a context name, a case-sensitive string of 1 to 32 characters.

Examples

# Configure the context name as isis for the SNMP object for managing IS-IS process 1.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] snmp context-name isis

snmp-agent trap enable isis

Use snmp-agent trap enable isis to enable IS-IS SNMP notifications.

Use undo snmp-agent trap enable isis to disable IS-IS SNMP notifications.

Syntax

Default

IS-IS SNMP notifications are enabled.

Views

System view

Predefined user roles

network-admin

Parameters

adjacency-state-change: Specifies notifications about IS-IS adjacency status changes.

area-mismatch: Specifies notifications about area address mismatches between hello packets.

authentication: Specifies notifications about authentication failures of IS-IS packets.

authentication-type: Specifies notifications about authentication type errors of IS-IS packets.

buffsize-mismatch: Specifies notifications about buffer size mismatches for LSPs.

id-length-mismatch: Specifies notifications about system ID length mismatches of IS-IS packets.

lsdboverload-state-change: Specifies notifications about LSDB overload state changes.

lsp-corrupt: Specifies notifications about LSP checksum errors in the LSDB.

lsp-parse-error: Specifies notifications about LSP packet parse failures.

lsp-size-exceeded: Specifies notifications about propagation failures caused by oversized LSPs.

manual-address-drop: Specifies notifications about manually configured area addresses that have been dropped.

max-seq-exceeded: Specifies notifications about attempts to exceed the maximum LSP sequence number.

maxarea-mismatch: Specifies notifications about maximum area address mismatches of hello packets.

own-lsp-purge: Specifies notifications about attempts to remove the local LSP.

protocol-support: Specifies notifications about supported-protocol mismatches.

rejected-adjacency: Specifies notifications about adjacency creation failures.

skip-sequence-number: Specifies notifications about LSP sequence number duplications.

version-skew: Specifies notifications about hello packet version mismatches.

Usage guidelines

If you do not specify a notification, this command enables all IS-IS SNMP notifications.

If no IS-IS process exists, the configuration is not allowed.

This function does not take effect if all configured IS-IS processes are deleted.

Examples

# Disable IS-IS SNMP notifications.

<Sysname> system-view

[Sysname] undo snmp-agent trap enable isis

snmp-agent trap isis adjacency-state-change extended

Use snmp-agent trap isis adjacency-state-change extended to extend the format of SNMP notifications for neighbor state changes.

Use undo snmp-agent trap isis adjacency-state-change extended to restore the default.

Syntax

snmp-agent trap isis adjacency-state-change extended

undo snmp-agent trap isis adjacency-state-change extended

Default

IS-IS does not extend the format of SNMP notifications for neighbor state changes.

Views

System view

Predefined user roles

network-admin

Usage guidelines

After you execute this command, IS-IS generates a notification in extended format when the state of a neighbor changes. Compared with notifications in standard format, notifications in extended format include interface names additionally, which enables the network administrator to quickly locate problems.

If the NMS does not support notifications in extended format, the NMS might fail to parse the notifications after you execute this command.

Examples

# Extend the format of SNMP notifications for neighbor state changes.

<Sysname> system-view

[Sysname] snmp-agent trap isis adjacency-state-change extended

summary

Use summary to configure a summary route.

Use undo summary to remove a summary route.

Syntax

In IS-IS IPv4 unicast address family view:

summary ip-address { mask-length | mask } [ avoid-feedback | generate_null0_route | [ level-1 | level-1-2 | level-2 ] | tag tag ] *

undo summary ip-address { mask-length | mask } [ level-1 | level-1-2 | level-2 ]

In IS-IS IPv6 unicast address family view:

undo summary ipv6-prefix prefix-length [ level-1 | level-1-2 | level-2 ]

Default

No summary route is configured.

Views

IS-IS IPv4 unicast address family view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

ip-address: Specifies the destination IP address of the summary route.

mask-length: Specifies the mask length of the summary route, in the range of 0 to 32.

mask: Specifies the mask of the destination IP address, in dotted decimal notation.

ipv6-prefix: Specifies an IPv6 prefix for the summary route.

prefix-length: Specifies the length of the IPv6 prefix, in the range of 0 to 128.

avoid-feedback: Avoids learning summary routes by route calculation.

generate_null0_route: Generates the Null 0 route to avoid routing loops.

level-1: Summarizes only the routes redistributed to Level-1.

level-1-2: Summarizes the routes redistributed to both Level-1 and Level-2.

level-2: Summarizes only the routes redistributed to Level-2.

tag tag: Specifies a management tag in the range of 1 to 4294967295.

Usage guidelines

To reduce the size of the routing table, as well as the size of LSP and LSDB generated by the device, summarize multiple contiguous networks into a single network. You can summarize native IS-IS routes and redistributed routes. After summarization, the cost of the summary route is the smallest cost of the summarized routes.

If no level is specified, only level-2 routes are summarized.

The device summarizes only routes generated from local LSPs.

Examples

# Configure a summary route of 202.0.0.0/8.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] address-family ipv4

[Sysname-isis-1-ipv4] summary 202.0.0.0 255.0.0.0

timer lsp-arrival

Use timer lsp-arrival to set the LSP receiving interval.

Use undo timer lsp-arrival to remove the configuration.

Syntax

timer lsp-arrival maximum-interval [ minimum-interval [ incremental-interval ] ] [ level-1 | level-2 ]

undo timer lsp-arrival [ level-1 | level-2 ]

Default

The LSP receiving interval is not set.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

maximum-interval: Specifies the maximum LSP receiving interval in the range of 1 to 120 seconds.

minimum-interval: Specifies the minimum LSP receiving interval in the range of 10 to 60000 milliseconds.

incremental-interval: Specifies the incremental interval in the range of 10 to 60000 milliseconds.

level-1: Applies the intervals to Level-1.

level-2: Applies the intervals to Level-2.

Usage guidelines

When the network is stable, IS-IS uses the minimum receiving interval. When network changes become frequent, the receiving interval increases by the incremental interval each time the same LSP is received until the maximum receiving interval is reached.

The minimum LSP receiving interval and the incremental interval cannot be greater than the maximum LSP receiving interval.

If no level is specified, the specified intervals apply to both Level-1 and Level-2.

Examples

# Set the maximum receiving interval, minimum receiving interval, and incremental interval for Level-1 LSPs to 10 seconds, 100 milliseconds, and 200 milliseconds, respectively.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] timer lsp-arrival 10 100 200 level-1

timer lsp-flood suppress-flapping

Use timer lsp-flood suppress-flapping to suppress LSP flooding when route flapping occurs.

Use undo timer lsp-flood suppress-flapping to remove the configuration.

Syntax

timer lsp-flood suppress-flapping delay-interval [ threshold threshold-value ] [ level-1 | level-2 ]

undo timer lsp-flood suppress-flapping [ level-1 | level-2 ]

Default

IS-IS does not suppress LSP flooding.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

delay-interval: Specifies the delay time in the range of 0 to 65535 seconds.

threshold threshold-value: Specifies the number of route flaps that trigger the delay timer, in the range of 3 to 100. The default number is 5.

level-1: Applies the configuration to Level-1.

level-2: Applies the configuration to Level-2.

Usage guidelines

If no level is specified, the configuration applies to both Level-1 and Level-2.

Examples

# Suppress Level-1 LSP flooding for 5 seconds after the number of route flaps reaches 10.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] timer lsp-flood suppress-flapping 5 threshold 10 level-1

timer lsp-generation

Use timer lsp-generation to set the LSP generation interval.

Use undo timer lsp-generation to remove the configuration.

Syntax

timer lsp-generation maximum-interval [ minimum-interval [ incremental-interval ] ] [ level-1 | level-2 ]

undo timer lsp-generation [ level-1 | level-2 ]

Default

The maximum interval is 5 seconds, the minimum interval is 50 milliseconds, and the incremental interval is 200 milliseconds.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

maximum-interval: Specifies the maximum interval in the range of 1 to 120 seconds.

minimum-interval: Specifies the minimum interval in the range of 10 to 60000 milliseconds.

incremental-interval: Specifies the incremental interval in the range of 10 to 60000 milliseconds.

level-1: Applies the intervals to Level-1.

level-2: Applies the intervals to Level-2. If no level is specified, the specified intervals apply to both Level-1 and Level-2.

Usage guidelines

By adjusting the LSP generation interval, you can prevent bandwidth and device resources from being over consumed due to frequent topology changes.

If you specify only the maximum-interval argument, the LSP generation interval is maximum-interval.

If you do not specify the incremental-interval argument, the LSP generation interval is in the range of minimum-interval to maximum-interval.

If you specify the incremental-interval argument, the LSP generation interval is as follows:

· When network changes are not frequent, the minimum-interval is adopted.

· When network changes are frequent, the LSP generation interval increases by incremental-interval × 2n-2 (n is the number of calculation times) each time a generation occurs until the maximum-interval is reached.

The minimum interval and the incremental interval cannot be greater than the maximum interval.

Examples

# Set the maximum interval, minimum interval, and incremental interval to 10 seconds, 100 milliseconds, and 200 milliseconds, respectively.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1]timer lsp-generation 10 100 200

timer lsp-generation suppress-flapping

Use timer lsp-generation suppress-flapping to suppress LSP generation when route flapping occurs.

Use undo timer lsp-generation suppress-flapping to remove the configuration.

Syntax

timer lsp-generation suppress-flapping delay-interval [ threshold threshold-value] [ level-1 | level-2 ]

undo timer lsp-generation suppress-flapping [ level-1 | level-2 ]

Default

IS-IS does not suppress LSP generation.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

delay-interval: Specifies the delay time in the range of 0 to 65535 seconds.

threshold threshold-value: Specifies the number of route flaps that trigger the delay timer, in the range of 3 to 100. The default number is 5.

level-1: Applies the configuration to Level-1.

level-2: Applies the configuration to Level-2.

Usage guidelines

If no level is specified, the configuration applies to both Level-1 and Level-2.

Examples

# Suppress Level-1 LSP generation for 3 seconds after the number of route flaps reaches 10.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] timer lsp-generation suppress-flapping 3 threshold 10 level-1

timer lsp-max-age

Use timer lsp-max-age to set the LSP maximum age in the LSDB.

Use undo timer lsp-max-age to restore the default.

Syntax

timer lsp-max-age seconds

undo timer lsp-max-age

Default

The LSP maximum age in the LSDB is 1200 seconds.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

seconds: Specifies the LSP maximum aging time in the range of 1 to 65535 seconds.

Usage guidelines

Each LSP has an age that decreases in the LSDB. Any LSP with an age of 0 is deleted from the LSDB. You can adjust the age value based on the scale of a network.

Examples

# Set the maximum LSP age to 1500 seconds.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] timer lsp-max-age 1500

Related commands

timer lsp-refresh

Use timer lsp-refresh to set the LSP refresh interval.

Use undo timer lsp-refresh to restore the default.

Syntax

timer lsp-refresh seconds

undo timer lsp-refresh

Default

The default LSP refresh interval is 900 seconds.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

seconds: Specifies the LSP refresh interval in the range of 1 to 65534 seconds.

Usage guidelines

Each device refreshes its LSPs at a configurable interval and sends them to other devices to achieve the following purposes:

· Prevent valid routes from aging out.

· Synchronize LSPs in the network.

A smaller refresh interval speeds up network convergence but consumes more bandwidth.

To refresh LSPs before they are aged out, the interval configured by the timer lsp-refresh command must be smaller than that configured by the timer lsp-max-age command.

Examples

# Set the LSP refresh interval to 1500 seconds.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] timer lsp-refresh 1500

Related commands

timer lsp-max-age

timer purge-zero-lsp route-calculate-delay

Use timer purge-zero-lsp route-calculate-delay to suppress route calculation after fragment 0 of a purge LSP is received.

Use undo timer purge-zero-lsp route-calculate-delay to remove the configuration.

Syntax

timer purge-zero-lsp route-calculate-delay delay-interval [ level-1 | level-2 ]

undo timer purge-zero-lsp route-calculate-delay [ level-1 | level-2 ]

Default

IS-IS suppresses route calculation for 10 seconds after fragment 0 of a purge LSP is received.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

delay-interval: Specifies the delay time in the range of 0 to 65535 seconds.

level-1: Applies the delay time to Level-1.

level-2: Applies the delay time to Level-2.

Usage guidelines

If no level is specified, the delay time applies to both Level-1 and Level-2.

Examples

# Suppress route calculation for 15 seconds after fragment 0 of a purge LSP is received.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] timer purge-zero-lsp route-calculate-delay 15 level-1

timer route-calculate suppress-flapping

Use timer route-calculate suppress-flapping to suppress route calculation when route flapping occurs.

Use undo timer route-calculate suppress-flapping to remove the configuration.

Syntax

timer route-calculate suppress-flapping delay-interval [ threshold threshold-value ] [ level-1 | level-2 ]

undo timer route-calculate suppress-flapping [ level-1 | level-2 ]

Default

IS-IS does not suppress route calculation.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

delay-interval: Specifies the delay time in the range of 0 to 65535 seconds.

threshold threshold-value: Specifies the number of route flaps that trigger the delay timer, in the range of 3 to 100. The default number is 5.

level-1: Applies the configuration to Level-1.

level-2: Applies the configuration to Level-2.

Usage guidelines

If no level is specified, the configuration applies to both Level-1 and Level-2.

Examples

# Suppress route calculation for 5 seconds after the number of route flaps reaches 10.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] timer route-calculate suppress-flapping 5 threshold 10 level-1

timer spf

Use timer spf to set the SPF calculation interval.

Use undo timer spf to restore the default.

Syntax

timer spf { maximum-interval [ minimum-interval [ incremental-interval [ conservative ] ] ] | millisecond millisecond-interval } [ exclude-prc ]

undo timer spf

Default

The maximum SPF calculation interval is 5 seconds, the minimum interval is 50 milliseconds, and the incremental interval is 200 milliseconds.

Views

IS-IS view

IS-IS IPv6 unicast address family view

Predefined user roles

network-admin

Parameters

maximum-interval: Specifies the maximum SPF calculation interval in the range of 1 to 120 seconds.

minimum-interval: Specifies the minimum SPF calculation interval in the range of 10 to 60000 milliseconds.

incremental-interval: Specifies the incremental SPF calculation interval in the range of 10 to 60000 milliseconds.

conservative: Keeps the maximum interval when route flapping occurs. If you do not specify this keyword, the minimum interval is used after SPF calculation is performed at the maximum interval for three consecutive times.

millisecond millisecond-interval: Specifies the fixed SPF calculation interval in the range of 0 to 10000 milliseconds.

exclude-prc: Configures IS-IS to perform SPF calculation immediately upon route prefix changes.

Usage guidelines

Based on the LSDB, an IS-IS device uses the SPF algorithm to calculate a shortest path tree with itself being the root, and uses the shortest path tree to determine the next hop to a destination network. By adjusting the SPF calculation interval, you can prevent bandwidth and device resources from being overused due to frequent topology changes.

When network changes are not frequent, the minimum-interval is adopted. If network changes become frequent, the SPF calculation interval increases by the incremental-interval each time a generation happens until the maximum-interval is reached.

The minimum interval and the incremental interval cannot be greater than the maximum interval.

As a best practice to speed up route convergence triggered by route prefix changes, specify the exclude-prc keyword for the timer spf command.

Examples

# Set the maximum interval to 10 seconds, the minimum interval to 100 milliseconds, and the incremental interval to 300 milliseconds, respectively.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] timer spf 10 100 300

virtual-system

Use virtual-system to configure a virtual system ID for the IS-IS process.

Use undo virtual-system to remove a virtual system ID.

Syntax

virtual-system virtual-system-id

undo virtual-system virtual-system-id

Default

No virtual system ID is configured.

Views

IS-IS view

Predefined user roles

network-admin

Parameters

virtual-system-id: Specifies a virtual system ID for the IS-IS process.

Examples

# Set a virtual system ID of 2222.2222.2222 for IS-IS process 1.

<Sysname> system-view

[Sysname] isis 1

[Sysname-isis-1] virtual-system 2222.2222.2222

04-Layer 3—IP Routing Command Reference

display osi

filter-policy import

import-route isis level-1 into level-2

isis bfd session-restrict-adj

isis circuit-type p2p

isis enable

isis fast-reroute lfa-backup exclude

isis timer hello

isis timer holding-multiplier

isis timer lsp

is-name

lsp-length originate

timer lsp-refresh

virtual-system

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources