interface-type interface-number: Specifies an interface by its type and number. If you do not specify this argument, the default setting will be restored. Currently, you can only bind a Layer 3 physical interface to an interface.

Usage guidelines

Before enabling iFIT measurement on the ingress point of an instance, execute this command to bind an interface to the instance. After you bind an interface to an instance, iFIT parses the packets passing through the interface to identify the target packets and add an iFIT header to each target packets. Meanwhile, iFIT will count the number of target packets, and send the packet count and timestamp to the analyzer at intervals through gRPC.

Examples

# Bind interface GigabitEthernet0/0/1 to instance abc.

<Sysname> system-view

[Sysname] ifit enable

[Sysname-ifit] instance abc

[Sysname-ifit-instance-abc] bind interface gigabitethernet 0/0/1

delay-measure disable

Use delay-measure disable to disable packet delay measurement.

Use undo delay-measure disable to enable packet delay measurement.

Syntax

delay-measure disable

undo delay-measure disable

Default

Packet delay measurement is enabled.

Views

iFIT instance view

Predefined user roles

network-admin

Usage guidelines

By default, packet delay measurement is enabled. You can execute this command to disable packet delay measurement as required.

Examples

# Disable packet delay measurement.

[Sysname] ifit enable

[Sysname-ifit] instance abc

[Sysname-ifit-instance-abc] delay-measure disable

delete dynamic-flow

Use delete dynamic-flow to delete iFIT dynamic flows.

Syntax

delete dynamic-flow { all | device-id device-id flow-id flow-id }

Views

iFIT view

Predefined user roles

network-admin

Parameters

all: Specifies all dynamic flows.

device-id device-id: Specifies an iFIT device by its ID in the range of 1 to 1048575.

flow-id flow-id: Specifies an iFIT flow by its ID in the range of 1 to 1048575.

Usage guidelines

A flow ID is generated on the ingress point and passed to the transmit points and egress point. A flow ID and a device ID uniquely identify a flow and you can execute the display ifit instance command to view the flow ID.

Examples

# Delete the dynamic flow with device ID 2 and flow ID 4098.

<Sysname> system-view

[Sysname] ifit enable

[Sysname-ifit] delete dynamic-flow device-id 2 flow-id 4098

device-id

Use device-id to specify a device ID.

Use undo device-id to restore the default.

Syntax

device-id device-id

undo device-id

Default

No device ID is specified.

Views

iFIT view

Predefined user roles

network-admin

Parameters

device-id: Specifies a device ID in the range of 1 to 1048575.

Usage guidelines

A device ID uniquely identifies a device in an iFIT network. To make iFIT function correctly, specify a device ID and make sure the specified device ID is unique.

Examples

# Specify 100 as the device ID.

<Sysname> system-view

[Sysname] ifit enable

[Sysname-ifit] device-id 100

display ifit global-information

Use display ifit global-information to display global iFIT flow information.

Syntax

display ifit global-information

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display global iFIT flow information.

<Sysname> display ifit global-information

Current instance count : 2

Enabled instance count : 1

Current static flow count : 1

Current dynamic flow count : 1

Table 1 Command output

Field	Description
Current instance count	Number of configured iFIT instances.
Enabled instance count	Number of instances enabled with iFIT.
Current static flow count	Number of static flows.
Current dynamic flow count	Number of dynamic flows.

‌

display ifit instance

Use display ifit instance to display iFIT instance information.

Syntax

display ifit instance [ instance-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

instance-name: Specifies an iFIT instance by its name, a case-sensitive string of 1 to 31 characters.

Examples

# Display IPv4 iFIT instance information.

<Sysname> display ifit instance 1

Instance name : 1

Device ID : 1

Flow information:

Flow type : Static

Flow direction : Unidirection

Source IP/mask length : 1.1.1.1/24

Destination IP/mask length : 2.2.2.2/32

Protocol : TCP

Source port : Any

Destination port : Any

DSCP : 23

VPN instance name : --

Measurement information:

Period : 10 sec

Measurement mode : e2e

Loss measurement : Enabled

Delay measurement : Enabled

Measurement configuration : Disabled

Measurement status : Inactive

Flow items:

Flow ID Interface

1 GigabitEthernet0/0/1

# Display the IPv6 static flow configuration.

<Sysname> display ifit instance 3

Instance name : 3

Device ID : 1

Flow information:

Flow type : Static

Flow direction : Unidirection

Source IPv6/prefix length : 1::1/68

Destination IPv6/prefix length : 2::2/128

Protocol : UDP

Source port : 8080

Destination port : 2308

DSCP : --

VPN instance name : vpn3

Measurement information:

Period : 30 sec

Measurement mode : e2e

Loss measurement : Enabled

Delay measurement : Enabled

Measurement configuration : Enabled

Measurement status : Active

Flow items:

Flow ID Interface

11 GigabitEthernet0/0/1

12 GigabitEthernet0/0/2

Table 2 Command output

Field	Description
Instance Name	iFIT instance name.
Device ID	iFIT device ID.
Flow information	iFIT target flow information.
Flow type	iFIT flow type: · Static. · Dynamic.
Flow direction	iFIT flow direction.
Source IP/maskLength	Source IP address and mask length of the target flow.
Destination IP/maskLength	Destination IP address and mask length of the target flow.
Source IPv6/prefix length	Source IPv6 address and prefix length of the target flow.
Destination IPv6/prefix length	Destination IPv6 address and prefix length of the target flow.
Protocol	Target flow protocol: · any. · udp. · tcp. · sctp.
Source port	Source port number of the target flow.
Destination port	Destination port number of the target flow.
DSCP	DSCP value of the target flow.
VPN-instance name	Name of the VPN instance bound to the iFIT flow.
Measurement information	Measurement information.
Period	Measurement period.
Measurement mode	Measurement mode: · e2e—End to end measurement. · trace—Hop by hop measurement.
Loss measurement	Whether packet loss measurement is enabled: · Enabled. · Disabled.
Delay measurement	Whether delay measurement is enabled: · Enabled. · Disabled.
Measurement configuration	Whether measurement is enabled: · Enabled. · Disabled.
Measurement status	Actual measurement state: · Active—iFIT measurement is in progress. · Inactive—iFIT measurement has not started.
Flow items	iFIT target flow. Flow information is displayed only when the measure enable command is executed.
Flow ID	iFIT target flow ID. -- indicates that the flow has not been assigned with an ID.
Interface	Interface bound to the iFIT target flow. All indicates that the iFIT flow has been bound to all Layer 3 physical interfaces.

‌

display ifit flow dynamic

Use display ifit flow dynamic to display dynamic flow information.

Syntax

display ifit flow dynamic [ device-id device-id flow-id flow-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

device-id device-id: Specifies an iFIT device by its ID in the range of 1 to 1048575.

flow-id flow-id: Display information about a dynamic flow by its ID. The value range for the flow-id argument is 1 to 1048575.

Usage guidelines

A transmit point or the egress point parses the received packets and identifies the target flow according to the iFIT headers of the packets. A dynamic flow is identified by the device ID and flow ID in the iFIT headers of the packets. If the device does not receive the packets using the same device ID and the same flow ID for a period of time, the device will age out the dynamic flow entry.

A flow ID is generated on the ingress point and passed to the transmit points and egress point. A flow ID and device ID uniquely identify a flow and you can execute the display ifit instance command to view the flow ID.

Examples

# Display dynamic flow information.

<Sysname> display ifit flow dynamic

Device ID : 1

Flow ID : 4099

Flow type : Dynamic

Flow direction : Unidirection

Period : 10 sec

Actual aging-time : 300 sec

Interface information

Name Direction

GigabitEthernet0/0/1 TransitInput

GigabitEthernet0/0/2 TransitOutput

Table 3 Command output

Field	Description
Device ID	iFIT device ID.
Flow ID	Flow ID of a dynamic flow.
Flow type	Flow type: · Static. · Dynamic.
Flow direction	Flow direction. If the field value is Unidirection, the flow is a unidirectional flow.
Period	Measurement period in seconds.
Actual aging-time	Actual time when the dynamic flow is aged out.
Interface information	Information about the interfaces that receive the dynamic flow.
Name	Interface name.
Direction	Flow direction for the interface: · Ingress—The target flow enters the transit network from this interface. · TransitInput—The target flow enters the node from this interface. · TransitOutput—The target flow leaves the node from this interface. · Egress—The target flow leaves the transit network from this interface.

‌

display ifit flow static

Use display ifit flow static to display static flow information for the most recent 10 measurement periods.

Syntax

display ifit flow static [ flow-id flow-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

flow-id flow-id: Display information about a static flow by its ID. The value range for the flow-id argument is 1 to 1048575.

Usage guidelines

You can specify a flow on the ingress point by using any combination of the following items: source IP address/segment, source port number, destination IP address/segment, destination port number, protocol type, DSCP value, and VPN instance. If a packet matches the configured items, the ingress point will add an iFIT header to the packet and the flow is the static flow.

Examples

# Display the IPv4 static flow configuration.

<Sysname> display ifit flow static flow-id 4097

Instance name : 1

Device ID : 1

Flow ID : 4097

Flow information:

Flow type : Static

Flow direction : Unidirection

Source IP/mask length : 1.1.1.1/24

Destination IP/mask length : 2.2.2.2/32

Protocol : TCP

Source port : Any

Destination port : Any

DSCP : 23

VPN instance name : --

Measurement information:

Period : 10 sec

Measurement mode : e2e

Loss measurement : Enabled

Delay measurement : Enabled

Measurement configuration : Enabled

Measurement status : Active

Bound interface:

All

# Display the IPv6 static flow configuration.

<Sysname> display ifit flow static flow-id 4099

Instance name : 3

Device ID : 1

Flow ID : 4099

Flow information:

Flow type : Static

Flow direction : Unidirection

Source IPv6/prefix length : 1::1/68

Destination IPv6/prefix length : 2::2/128

Protocol : UDP

Source port : 8080

Destination port : 2308

DSCP : --

VPN instance name : vpn3

Measurement information:

Period : 30 sec

Measurement mode : e2e

Loss measurement : Enabled

Delay measurement : Enabled

Measurement configuration : Enabled

Measurement status : Active

Bound interface:

GigabitEthernet0/0/1

Table 4 Command output

Field	Description
Instance Name	Name of the iFIT instance.
Device ID	ID of the device that generates the iFIT target flow.
Flow ID	Flow ID of the target flow.
Flow information	Information about the target flow.
Flow type	Flow type: · Static. · Dynamic.
Flow direction	Flow direction. If the field value is Unidirection, the flow is a unidirectional flow.
Source IP/maskLength	Source IP address and mask length.
Destination IP/maskLength	Destination IP address and mask length.
Source IPv6/prefix length	Source IPv6 address and prefix length.
Destination IPv6/prefix length	Destination IPv6 address and prefix length.
Protocol	Protocol: · Any. · UDP. · TCP. · SCTP.
Source port	Source port number.
Destination port	Destination port number.
DSCP	DSCP value of the target flow.
VPN-instance name	Name of the VPN instance bound to the target flow.
Measurement information	Information about iFIT measurement.
Period	Measurement period.
Measurement mode	Measurement mode: · trace—Hop-by-hop measurement. · e2e—End-to-end measurement.
Next hop configuration	Configured next hop.
Loss measurement	Delay measurement state: · Enabled. · Disabled.
Delay measurement	Loss measurement state: · Enabled. · Disabled.
Measurement configuration	Configured measurement state: · Enabled. · Disabled.
Measurement status	Actual measurement state: · Active—iFIT measurement is in progress. · Inactive—iFIT measurement has not started.
Bound interface	Interface bound with the target flow.

‌

display ifit statistic

Use display ifit statistic to display statistics about an iFIT flow for the most recent 10 measurement periods.

Syntax

display ifit statistic device-id device-id flow-id flow-id [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

device-id device-id: Specifies an iFIT device by its ID in the range of 1 to 1048575.

flow-id flow-id: Displays statistics about an iFIT flow by its flow ID. The value range for the flow-id argument is 1 to 1048575.

verbose: Displays detailed statistics about an iFIT flow. If you do not specify this keyword, this command displays brief statistics about an iFIT flow.

Usage guidelines

Examples

# Display brief measurement information about the flow with device ID 1 and flow ID 123.

<Sysname> display ifit statistic device-id 1 flow-id 123

Period ID Direction Interface PktCount Timestamp (sec, nsec)

159627365 TransitIn GE0/0/1 1500 1596273655,349433112

# Display detailed measurement information about the flow with device ID 1 and flow ID 123.

<Sysname> display ifit statistic device-id 1 flow-id 123 verbose

Period ID : 159627365

Period started at : 2020-08-01 17:20:55

Direction : TransitInput

Interface : GigabitEthernet0/0/1

PktCount : 1500

ByteCount : 1295489456450

Timestamp (sec, nsec): 2020-08-01 17:20:55.349433112 (1619278726, 349433112)

TTL : 189

Table 5 Command output

Field	Description
PeriodID	Measurement period number.
Period started at	Start time of the measurement period.
Direction	Flow direction of the interface: · Ingress—The target flow enters the transit network from this interface. · TransitIn—The target flow enters the node from this interface. You can view this value only in the simplified iFIT flow statistics. · TransitInput—The target flow enters the node from this interface. You can view this value only in the detailed iFIT flow statistics. · TransitOut—The target flow leaves the node from this interface. You can view this value only in the simplified iFIT flow statistics. · TransitOutput—The target flow leaves the node from this interface. You can view this value only in the detailed iFIT flow statistics. · Egress—The target flow leaves the transit network from this interface.
Interface	Interface name.
PktCount	Number of packets measured in the period.
ByteCount	Number of bytes detected in the period.
Timestamp (sec, nsec)	Timestamp value for the delay measurement. In the detailed information, this field is displayed in the YY-MM-DD HH:MM:SS.nanosecond format.
TTL	TTL value of the packet.

‌

dynamic-flow aging-time

Use dynamic-flow aging-time to specify the aging time for dynamic flows.

Use undo dynamic-flow aging-time to restore the default.

Syntax

dynamic-flow aging-time multi-value

undo dynamic-flow aging-time

Default

The aging time for dynamic flows is 10 times the measurement period and it cannot be less than 5 minutes.

Views

iFIT view

Predefined user roles

network-admin

Parameters

multi-value: Specifies a multiplier value. The aging time for dynamic flows is equal to the measurement period multiplied by the multiplier value. The value range is 2 to 100.

Usage guidelines

The aging time for dynamic flows must be equal to or greater than 5 minutes. If the configured aging time is less than 5 minutes, the actual aging time will be 5 minutes.

Examples

# Configure the aging time for dynamic flows to be 20 times the measurement period.

<Sysname> system-view

[Sysname] ifit enable

[Sysname-ifit] dynamic-flow aging-time 20

flow

Use flow to specify a static flow to be monitored by an iFIT instance.

Use undo flow to remove the static flow settings.

Syntax

flow unidirection source-ip src-ip-address [ src-mask-length ] destination-ip dest-ip-address [ dest-mask-length ] [ protocol { { tcp | udp | sctp } [ source-port src-port-number ] [ destination-port dest-port-number ] | protocol-number } ] [ dscp dscp-value ] [ vpn-instance vpn-instance-name ]

flow unidirection source-ipv6 src-ipv6-address [ src-prefix-length ] destination-ipv6 dest-ipv6-address [ dest-prefix-length ] [ protocol { { tcp | udp | sctp } [ source-port src-port-number ] [ destination-port dest-port-number ] | protocol-number } ] [ dscp dscp-value ] [ vpn-instance vpn-instance-name ]

undo flow

Default

No static flow is specified for an iFIT instance.

Views

iFIT instance view

Predefined user roles

network-admin

Parameters

unidirection: Specifies the unidirectional flows.

source-ip src-ip-address: Specifies a source IPv4 address of the flow, in dotted decimal format.

src-mask-length: Specifies a mask length for the source IPv4 address. The value range is 1 to 32. If you do not specify this argument, the exact match of the source IPv4 address is used.

destination-ip dest-ip-address: Specifies a destination IPv4 address of the flow, in dotted decimal format.

dest-mask-length: Specifies a mask length for the destination IPv4 address. The value range is 1 to 32. If you do not specify this argument, the exact match of the source IPv4 address is used.

source-ipv6 src-ipv6-address: Specifies a source IPv6 address of the flow.

src-prefix-length: Specifies a prefix length for the source IPv6 address. The value range is 1 to 128. If you do not specify this argument, the exact match of the source IPv6 address is used.

destination-ipv6 dest-ipv6-address: Specifies a destination IPv6 address of the flow.

dest-prefix-length: Specifies a prefix length for the destination IPv6 address. The value range is 1 to 128. If you do not specify this argument, the exact match of the destination IPv6 address is used.

protocol: Specifies a protocol type of the flow. If you do not specify this keyword, the flow can use any protocol.

· { tcp | udp | sctp }: Specifies the TCP, UDP, or SCTP protocol.

· destination-port dest-port-number: Specifies a destination port number. The value range is 0 to 65535. If you do not specify this option, the flow can use any port number as the destination port number.

· source-port src-port-number: Specifies a source port number. The value range is 0 to 65535. If you do not specify this option, the flow can use any port number as the source port number.

· protocol-number: Specifies the number of the protocol type. The value range is 0 to 255, excluding 6 (TCP protocol number), 17 (UDP protocol number), and 132 (SCTP protocol number).

dscp dscp-value: Specifies a DSCP value of the flow, in the range of 0 to 63.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. To specify a flow on the public network, do not specify this option.

Usage guidelines

The target flows are key elements for iFIT measurement. Before starting an iFIT measurement, you must execute this command to specify a flow to be measured on the ingress point. You do not need to specify a flow on the transmit points and egress point because the device can automatically learn the target flow through the iFIT header of the packets.

An iFIT instance can monitor only one flow. If you execute this command multiple times for the same iFIT instance, the most recent configuration takes effect.

For the flows to be monitored by different instances, the flow attributes must not be identical.

The source and destination IP addresses must be legal unicast IP addresses, and they cannot be broadcast or multicast IP addresses.

Examples

# Configure instance 1 to monitor the unidirectional flow from 10.10.10.1 to 10.10.10.2 with the VPN instance vpn1.

<Sysname> system-view

[Sysname] ifit enable

[Sysname-ifit] instance abc

[Sysname-ifit-instance-abc] flow unidirection source-ip 10.10.10.1 24 destination-ip 10.10.10.2 24 vpn-instance vpn1

ifit enable

Use ifit enable to enable the iFIT functionality globally and enter its view, or enter the existing iFIT view.

Use undo ifit enable to disable the iFIT functionality globally.

Syntax

ifit enable

undo ifit enable

Default

The iFIT functionality is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

To measure the packet loss and packet delay of the network in real time, you can enable iFIT measurement.

To start iFIT measurement, perform the following tasks:

· On the ingress point, enable the iFIT functionality, configure iFIT device ID, create an instance, and configure a flow to be monitored by the instance. The configured flow is a static flow. The ingress point automatically uses the device ID to generates a flow ID, and encapsulates the flow ID and local iFIT device ID in the iFIT header of packets transmitted to the transmit points and egress point. The flow ID uniquely identifies a flow.

· On the transmit points and egress point, enable the iFIT functionality. If the received packet carries an iFIT header, a transmit point or the egress point will perform iFIT measurement according to the flow ID, measurement period number, timestamp in the iFIT header.

Examples

# Enable iFIT and enter its view.

<Sysname> system-view

[Sysname] ifit enable

[Sysname-ifit]

instance

Use instance to create an iFIT instance and enter its view, or enter the view of an existing iFIT instance.

Use undo instance to delete an iFIT instance.

Syntax

instance instance-name

undo instance instance-name

Default

No iFIT instance exists.

Views

iFIT view

Predefined user roles

network-admin

Parameters

instance-name: Specifies an iFIT instance by its name. The instance name is a case-sensitive string of 1 to 31 characters.

Usage guidelines

You must configure an iFIT instance on the ingress point. You can configure target flow match criteria in instance view. An instance can be bound to multiple interfaces, and an interface is associated with one target flow.

To perform iFIT measurement on the transmit points and egress point, you only need to enable iFIT. After you enable iFIT on a transmit point or the egress point, the point automatically identifies the flow according to the iFIT header, and perform iFIT measurement on the flow. The flow identified automatically is a dynamic flow.

Examples

# Create iFIT instance abc and enter its view.

<Sysname> system-view

[Sysname] ifit enable

[Sysname-ifit] instance abc

[Sysname-ifit-abc]

measure enable

Use measure enable to enable iFIT measurement for an iFIT instance.

Use undo measure enable to disable iFIT measurement for an iFIT instance.

Syntax

measure enable

undo measure enable

Default

iFIT measurement for an iFIT instance is disabled.

Views

iFIT instance view

Predefined user roles

network-admin

Usage guidelines

You can execute this command to start iFIT measurement for an iFIT instance to monitor the packet delay and packet loss of the flow.

Before starting iFIT measurement, configure a device ID, create an iFIT instance, configure a flow, and bind the flow to an interface.

To modify the configuration for the device-id command or an iFIT enabled instance, disable iFIT measurement for the instance firstly.

Examples

# Enable iFIT measurement for iFIT instance abc.

[Sysname] ifit enable

[Sysname-ifit] instance abc

[Sysname-ifit-instance-abc] measure enable

measure mode

Use measure mode to specify an iFIT measurement mode.

Use undo measure mode to restore the default.

Syntax

measure mode { e2e | trace }

undo measure mode

Default

End-to-end measurement is used.

Views

iFIT instance view

Predefined user roles

network-admin

Parameters

e2e: Specifies end-to-end measurement. In this mode, only the ingress point and egress point report the measurement data.

trace: Specifies hop-by-hop measurement. In this mode, all points that are enabled with iFIT and receive the flow packets will report the measurement data.

Usage guidelines

iFIT measurement helps you to measure the network performance, troubleshoot the network faults, and measure the service quality.

To measure the packet loss and packet delay of the whole network, you can use end-to-end measurement. To accurately locate the packet loss and packet delay of each network node, you can use the hop-by-hop measurement.

Examples

# Specify hop-by-hop measurement as the measurement mode.

<Sysname> system-view

[Sysname] ifit enable

[Sysname-ifit] instance abc

[Sysname-ifit-instance-abc] measure mode trace

period

Use period to specify the measurement period for an iFIT instance.

Use undo period to restore the default.

Syntax

period period

undo period

Default

The measurement period for an iFIT instance is 30 seconds.

Views

iFIT instance view

Predefined user roles

network-admin

Parameters

period: Specifies the measurement period in seconds. Valid values include 1, 10, 30, 60, and 300.

Usage guidelines

Within each measurement period, an iFIT instance measures the packet quantity and timestamp of the packets passing through an interface.

Examples

# Specify 60 seconds as the measurement period for an iFIT instance.

<Sysname> system-view

[Sysname] ifit enable

[Sysname-ifit] instance abc

[Sysname-ifit-instance-abc] period 60

reset iFIT statistic

Use reset iFIT statistic to clear iFIT statistics for the most recent 10 measurement periods.

Syntax

reset ifit statistic [ device-id device-id flow-id flow-id | instance instance-name ]

Views

Any view

Predefined user roles

network-admin

Parameters

device-id device-id: Specifies an iFIT device by its ID in the range of 1 to 1048575.

flow-id flow-id: Clears statistics about an iFIT flow by its flow ID. The value range for the flow-id argument is 1 to 1048575.

instance instance-name: Clears statistics about an iFIT flow by its instance name. The instance name is a case-sensitive string of 1 to 31 characters. Only the ingress point supports instances. The transmit points and egress point do not support instances.

Usage guidelines

Examples

# Clear iFIT statistics generated in the most recent 10 measurement periods for the flow with device ID 1 and flow ID 40962.

<Sysname> reset ifit statistic device-id 1 flow-id 40962

21-Network Management and Monitoring Command Reference

iFIT commands

bind interface

delay-measure disable

delete dynamic-flow

device-id

display ifit global-information

display ifit instance

display ifit flow dynamic

display ifit flow static

display ifit statistic

dynamic-flow aging-time

flow

ifit enable

instance

measure enable

measure mode

period

reset iFIT statistic

Cloud & AI

InterConnect

Intelligent Computing

Security

SMB Products

Intelligent Terminal Products

Industry Solutions

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Training & Certification

Become a Partner

Partner Resources

Partner Business Management

Company Information

News & Events

Online Exhibition Center

Contact Us