09-VXLAN Command Reference

HomeSupportSwitchesS12500R SeriesReference GuidesCommand ReferencesH3C S12500R Switch Router Series Command References(R51xx)-6W10109-VXLAN Command Reference
02-VXLAN IP gateway commands
Title Size Download
02-VXLAN IP gateway commands 102.91 KB

VXLAN IP gateway commands

arp distributed-gateway dynamic-entry synchronize

Use arp distributed-gateway dynamic-entry synchronize to enable dynamic ARP entry synchronization for distributed VXLAN IP gateways.

Use undo arp distributed-gateway dynamic-entry synchronize to disable dynamic ARP entry synchronization for distributed VXLAN IP gateways.

Syntax

arp distributed-gateway dynamic-entry synchronize

undo arp distributed-gateway dynamic-entry synchronize

Default

Dynamic ARP entry synchronization is disabled for distributed VXLAN IP gateways.

Views

System view

Predefined user roles

network-admin

Usage guidelines

When local proxy ARP is enabled on distributed VXLAN IP gateways, each gateway learns ARP information independently. A gateway does not forward ARP packets destined for its local VSI interfaces to other gateways. For distributed VXLAN IP gateways to have the same ARP entries, you must enable dynamic ARP entry synchronization.

A controller or the EVPN feature can also synchronize ARP entries among distributed VXLAN IP gateways. When you use a controller or the EVPN feature, do not enable dynamic ARP entry synchronization.

Examples

# Enable dynamic ARP entry synchronization for distributed VXLAN IP gateways.

<Sysname> system-view

[Sysname] arp distributed-gateway dynamic-entry synchronize

Related commands

distributed-gateway local

local-proxy-arp enable (Layer 3—IP Services Command Reference)

display interface vsi-interface

Use display interface vsi-interface to display information about VSI interfaces.

Syntax

display interface [ vsi-interface [ vsi-interface-id ] ] [ brief [ description | down ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vsi-interface [ vsi-interface-id ]: Specifies VSI interfaces. If you specify a VSI interface, this command displays information about the specified interface. If you specify only the vsi-interface keyword, this command displays information about all VSI interfaces. If you do not specify the vsi-interface [ vsi-interface-id ] option, this command displays information about all interfaces. Make sure the specified VSI interfaces have been created on the device.

brief: Display brief interface information. If you do not specify this keyword, the command displays detailed interface information.

description: Displays complete interface descriptions. If you do not specify this keyword, the command displays only the first 25 characters of interface descriptions.

down: Displays interfaces that are physically down as well as the down reason. If you do not specify this keyword, the command does not filter output by physical interface state.

Examples

# Display information about VSI-interface 100.

<Sysname> display interface vsi-interface 100

Vsi-interface100

Current state: UP

Line protocol state: UP

Description: Vsi-interface100 Interface

Bandwidth: 1000000 kbps

Maximum transmission unit: 1500

Internet address: 10.1.1.1/24 (primary)

IP packet frame type: Ethernet II, hardware address: 0011-2200-0102

IPv6 packet frame type: Ethernet II, hardware address: 0011-2200-0102

Physical: Unknown, baudrate: 1000000 kbps

Last clearing of counters: Never

Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Input: 0 packets, 0 bytes, 0 drops

Output: 0 packets, 0 bytes, 0 drops

Table 1 Command output

Field

Description

Current state

Physical link state of the interface:

·     Administratively DOWN—The interface has been shut down by using the shutdown command.

·     DOWN—The interface is administratively up, but its physical state is down.

·     UP—The interface is both administratively and physically up.

Line protocol state

Data link layer state of the interface:

·     UP—The data link layer protocol is up.

·     UP(spoofing)—The data link layer protocol is up, but the link is an on-demand link or does not exist.

·     DOWN—The data link layer protocol is down.

Description

Description of the interface.

Bandwidth

Expected bandwidth of the interface.

Maximum transmission unit

MTU of the interface.

Internet protocol processing

IP packet processing capability of the interface when the interface is not assigned an IP address:

·     Disabled—The interface cannot process IP packets.

·     Enabled—The interface can process IP packets.

Internet address: ip-address/mask-length (Type)

IP address of the interface and type of the address in parentheses.

Possible IP address types include:

·     Primary—Manually configured primary IP address.

·     Sub—Manually configured secondary IP address. If the interface has both primary and secondary IP addresses, the primary IP address is displayed. If the interface has only secondary IP addresses, the lowest secondary IP address is displayed.

·     DHCP-Allocated—DHCP allocated IP address. For more information, see DHCP client configuration in Layer 3IP Services Configuration Guide.

·     BOOTP-AllocatedBOOTP allocated IP address. For more information, see BOOTP client configuration in Layer 3IP Services Configuration Guide.

·     Unnumbered—IP address borrowed from another interface.

·     Cellular-Allocated—IP address allocated through the modem manufacturer's proprietary protocol. For more information, see 3G/4G modem management in Layer 2WAN Access Configuration Guide.

IP packet frame type

IPv4 packet framing format.

hardware address

MAC address.

IPv6 packet frame type

IPv6 packet framing format.

Physical

Physical type of the interface, which is fixed at Unknown.

baudrate

Interface baudrate in kbps.

Last clearing of counters

Last time when the reset counters interface vsi-interface command was used to clear interface statistics.

This field displays Never if the reset counters interface vsi-interface command has never been used on the interface since the device startup.

Last 300 seconds input rate

Average input rate for the last 300 seconds.

Last 300 seconds output rate

Average output rate for the last 300 seconds.

Input: 0 packets, 0 bytes, 0 drops

Incoming traffic statistics on the interface:

·     Number of incoming packets.

·     Number of incoming bytes.

·     Number of dropped incoming packets.

Output: 0 packets, 0 bytes, 0 drops

Outgoing traffic statistics on the interface:

·     Number of outgoing packets.

·     Number of outgoing bytes.

·     Number of dropped outgoing packets.

 

# Display brief information about all VSI interfaces.

<Sysname> display interface vsi-interface brief

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface            Link Protocol Primary IP      Description

Vsi100               DOWN DOWN     --

# Display brief information and complete description for VSI-interface 100.

<Sysname> display interface vsi-interface 100 brief description

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface            Link Protocol Primary IP      Description

Vsi100               UP    UP      1.1.1.1         VSI-interface100

# Displays interfaces that are physically down and the down reason.

<Sysname> display interface brief down

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Interface            Link   Cause

Vsi100               DOWN   Administratively

Vsi200               DOWN   Administratively

Table 2 Command output

Field

Description

Interface

Abbreviated interface name.

Link

Physical link state of the interface:

·     UP—The interface is physically up.

·     DOWN—The interface is physically down.

·     ADM—The interface has been shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command.

Protocol

Data link layer protocol state of the interface:

·     UP—The data link layer protocol of the interface is up.

·     UP (s)—The data link layer protocol of the interface is up, but the link is an on-demand link or does not exist. The (s) attribute represents the spoofing flag.

·     DOWN—The data link layer protocol of the interface is down.

Primary IP

Primary IP address of the interface. This field displays two hyphens (--) if the interface does not have an IP address.

Description

Description of the interface.

Cause

Cause for the physical link state of an interface to be DOWN:

·     Administratively—The interface has been manually shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command.

·     Not connected—The interface is not mapped to any VSI, or the mapped VSI does not have any AC or VXLAN tunnel.

 

Related commands

reset counters interface vsi-interface

distributed-gateway local

Use distributed-gateway local to specify a VSI interface as a distributed gateway to provide services for the local site.

Use undo distributed-gateway local to restore the default.

Syntax

distributed-gateway local

undo distributed-gateway local

Default

A VSI interface is not a distributed gateway.

Views

VSI interface view

Predefined user roles

network-admin

Usage guidelines

If a VXLAN uses distributed gateway services, you must assign the same IP address to the VXLAN's VSI interfaces on different VTEPs. To avoid IP address conflicts, you must specify the VSI interface on each VTEP as a distributed gateway.

Examples

# Specify VSI-interface 100 as a distributed gateway.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] distributed-gateway local

gateway subnet

Use gateway subnet to assign a subnet to a VSI.

Use undo gateway subnet to remove a subnet from a VSI.

Syntax

gateway subnet ipv4-address wildcard-mask

undo gateway subnet ipv4-address wildcard-mask

Default

No subnet is assigned to a VSI.

Views

VSI view

Predefined user roles

network-admin

Parameters

ipv4-address: Specifies an IPv4 subnet address in dotted-decimal notation.

wildcard-mask: Specifies a wildcard mask in dotted decimal notation. In contrast to a network mask, the 0 bits in a wildcard mask represent "do care" bits, and the 1 bits represent "don't care" bits. If the "do care" bits in a packet's IP address are identical to the "do care" bits in the specified subnet address, the packet is assigned to the VSI. All "don't care" bits are ignored. The 0s and 1s in a wildcard mask can be noncontiguous. For example, 0.255.0.255 is a valid wildcard mask.

Usage guidelines

You must configure this command on VSIs that share a gateway interface. This command enables the VSI interface to identify the VSI of a packet.

You can assign a maximum of eight IPv4 subnets to a VSI.

You must specify a gateway interface for a VSI before you can assign subnets to the VSI. If you remove the gateway interface from the VSI, the VSI's subnet settings are automatically deleted.

For VSIs that share a gateway interface, the subnets must be unique.

Examples

# Assign subnet 100.0.10.0/24 to VSI vxlan.

<Sysname> system-view

[Sysname] vsi vxlan

[Sysname-vsi-vxlan] gateway subnet 100.0.10.0 0.0.0.255

gateway vsi-interface

Use gateway vsi-interface to specify a gateway interface for a VSI.

Use undo gateway vsi-interface to restore the default.

Syntax

gateway vsi-interface vsi-interface-id

undo gateway vsi-interface

Default

No gateway interface is specified for a VSI.

Views

VSI view

Predefined user roles

network-admin

Parameters

vsi-interface-id: Specifies a VSI interface by its number. The VSI interface number must exist.

Usage guidelines

When you delete a VSI interface by using the undo interface vsi-interface command, the gateway interface setting of the VSI interface is also deleted.

A VSI can have only one gateway interface. Multiple VSIs can share a gateway interface.

Examples

# Specify VSI-interface 100 as the gateway interface for VSI vpna.

<Sysname> system-view

[Sysname] vsi vpna

[Sysname-vsi-vpna] gateway vsi-interface 100

Related commands

interface vsi-interface

interface vsi-interface

Use interface vsi-interface to create a VSI interface and enter its view, or enter the view of an existing VSI interface.

Use undo interface vsi-interface to delete a VSI interface.

Syntax

interface vsi-interface vsi-interface-id

undo interface vsi-interface vsi-interface-id

Default

No VSI interfaces exist.

Views

System view

Predefined user roles

network-admin

Parameters

vsi-interface-id: Specifies a VSI interface number. The value range for this argument is 0 to 16383.

Usage guidelines

When you delete a VSI interface by using the undo interface vsi-interface command, the gateway interface setting of the VSI interface is also deleted.

Examples

# Create VSI-interface 100 and enter VSI interface view.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100]

Related commands

gateway vsi-interface

mac-address

Use mac-address to assign a MAC address to a VSI interface.

Use undo mac-address to restore the default.

Syntax

mac-address mac-address

undo mac-address

Default

VSI interfaces use the MAC address of VLAN-interface 4094.

Views

VSI interface view

Predefined user roles

network-admin

Parameters

mac-address: Specifies a MAC address in H-H-H format.

Examples

# Assign MAC address 0001-0001-0001 to VSI-interface 100.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] mac-address 1-1-1

vxlan tunnel arp-learning disable

Use vxlan tunnel arp-learning disable to disable remote ARP learning for VXLANs.

Use undo vxlan tunnel arp-learning disable to enable remote ARP learning for VXLANs.

Syntax

vxlan tunnel arp-learning disable

undo vxlan tunnel arp-learning disable

Default

Remote ARP learning is enabled for VXLANs.

Views

System view

Predefined user roles

network-admin

Usage guidelines

By default, the device learns ARP information of remote VMs from packets received on VXLAN tunnel interfaces. To save resources on VTEPs in an SDN transport network, you can temporarily disable remote ARP learning when the controller and VTEPs are synchronizing entries. After the entry synchronization is completed, use the undo vxlan tunnel arp-learning disable command to enable remote ARP learning.

As a best practice, disable remote ARP learning for VXLANs only when the controller and VTEPs are synchronizing entries.

Examples

# Disable remote ARP learning for VXLANs.

<Sysname> system

[Sysname] vxlan tunnel arp-learning disable

 

  • Cloud & AI
  • InterConnect
  • Intelligent Computing
  • Security
  • SMB Products
  • Intelligent Terminal Products
  • Product Support Services
  • Technical Service Solutions
All Services
  • Resource Center
  • Policy
  • Online Help
All Support
  • Become a Partner
  • Partner Resources
  • Partner Business Management
All Partners
  • Profile
  • News & Events
  • Online Exhibition Center
  • Contact Us
All About Us
新华三官网