Login
- Table of Contents
-
- 10-High Availability Command Reference
- 00-Preface
- 01-Ethernet OAM commands
- 02-CFD commands
- 03-DLDP commands
- 04-RRPP commands
- 05-ERPS commands
- 06-Smart Link commands
- 07-Monitor Link commands
- 08-Error code detection commands
- 09-VRRP commands
- 10-BFD commands
- 11-Track commands
- 12-Process placement commands
- 13-S-Trunk commands
- Related Documents
-
| Title | Size | Download |
|---|---|---|
| 02-CFD commands | 198.73 KB |
CFD commands
cfd cc enable
Use cfd cc enable to enable CCM sending on a specified MEP.
Use undo cfd cc enable to disable CCM sending on a specified MEP.
Syntax
cfd cc service-instance instance-id mep mep-id enable
undo cfd cc service-instance instance-id mep mep-id enable
Default
The CCM sending feature is disabled.
Views
Layer 2 Ethernet interface view
Layer 3 Ethernet interface view
Layer 2 aggregate interface view
Layer 3 Ethernet subinterface view
Layer 2 Ethernet service instance view
Layer 3 aggregate interface view
Layer 3 aggregate subinterface view
Predefined user roles
network-admin
Parameters
service-instance instance-id: Specifies the service instance ID in the range of 1 to 32767.
mep mep-id: Specifies a MEP by its ID in the range of 1 to 8191.
Usage guidelines
Follow these guidelines when you use the command:
· Configurations in Ethernet interface view take effect only on the current interface.
· If the MEP belongs to an MA that does not carry the VLAN attribute, configurations on a member port of an aggregate interface take effect only on the current member port.
· If the MEP belongs to an MA that carries the VLAN attribute, configurations on a member port of an aggregate interface take effect only when the member port leaves the aggregation group.
In an Ethernet network, you can enable CCM sending only on Layer 2/Layer 3 Ethernet interfaces and Layer 2 aggregate interfaces.
In an MPLS Layer 2 VPN, you can enable CCM sending only on Layer 3 Ethernet interfaces, Layer 3 Ethernet subinterfaces, Layer 3 aggregate interfaces, Layer 3 aggregate subinterfaces, and Layer 2 Ethernet service instances.
Examples
# On HundredGigE 1/0/1, enable CCM sending on MEP 3 in service instance 5.
<Sysname> system-view
[Sysname] interface hundredgige 1/0/1
[Sysname-HundredGigE1/0/1] cfd cc service-instance 5 mep 3 enable
# On HundredGigE 1/0/1.1, enable CCM sending on MEP 3 in service instance 5.
<Sysname> system-view
[Sysname] interface hundredgige 1/0/1.1
[Sysname-HundredGigE1/0/1.1] cfd cc service-instance 5 mep 3 enable
cfd cc interval
cfd cc interval
Use cfd cc interval to set the value of the interval field in the CCM messages.
Use undo cfd cc interval to remove the value of the interval field in the CCM messages.
Syntax
cfd cc interval interval-value service-instance instance-id
undo cfd cc interval [ interval-value ] service-instance instance-id
Default
The value of this field is 4 for all CCMs sent.
Views
System view
Predefined user roles
network-admin
Parameters
interval interval-value: Specifies the value of the interval field in CCM messages. The value range for the interval field is 1 to 7.
service-instance instance-id: Specifies the service instance ID in the range of 1 to 32767.
Usage guidelines
When setting the CCM interval, use the settings described in Table 1.
Table 1 CCM interval field encoding
|
CCM interval field |
Transmission interval |
Maximum CCM lifetime |
|
1 |
10/3 milliseconds |
35/3 milliseconds |
|
2 |
10 milliseconds |
35 milliseconds |
|
3 |
100 milliseconds |
350 milliseconds |
|
4 |
1 second |
3.5 seconds |
|
5 |
10 seconds |
35 seconds |
|
6 |
60 seconds |
210 seconds |
|
7 |
600 seconds |
2100 seconds |
Examples
# Set the value of the interval field to 3 in CCMs sent by MEPs in service instance 2.
<Sysname> system-view
[Sysname] cfd cc interval 3 service-instance 2
cfd cc enable
cfd dlm continual
Use cfd dlm continual to configure continual two-way loss measurement (LM).
Use undo cfd dlm continual to disable continual two-way LM.
Syntax
cfd dlm continual service-instance instance-id mep mep-id { target-mac mac-address | target-mep target-mep-id } [ dot1p dot1p-value ]
Default
Continual two-way LM is disabled.
Views
System view
Predefined user roles
network-admin
Parameters
service-instance instance-id: Specifies a service instance by its ID in the range of 1 to 32767.
mep mep-id: Specifies the source MEP by its ID in the range of 1 to 8191.
target-mac mac-address: Specifies the target MEP by its bridge MAC address, which is in the format of H-H-H.
target-mep target-mep-id: Specifies the target MEP by its ID in the range of 1 to 8191.
dot1p dot1p-value: Specifies an 802.1p priority for CCM frames. The value range for the dot1p-value argument is 0 to 7. The default value is 7.
Usage guidelines
The two-way LM function measures the frame loss between the source and target MEPs by using CCMs. The source MEP calculates the number of lost frames according to the counter values of two consecutive CCMs received (the current CCM and the previous CCM).
To view the bridge MAC address of the target MEP, execute the display lacp system-id command on the target MEP.
For the two-way LM function to take effect, you must configure it on both the local and peer devices.
If the frame counting mode is dot1p-based, you must specify the dot1p dot1p-value option. If the frame counting mode is port-based, do not specify the dot1p dot1p-value option.
To modify two-way LM settings for a source MEP, disable two-way LM and then reconfigure the function for the source MEP.
The two-way LM detection interval is the CCM interval. Before configuring two-way LM, configure the CCM interval field value to be greater than 2.
One-way LM and two-way LM cannot be configured at the same time for one source MEP. If you have configured short-period one-way LM or continual one-way LM, you can configure two-way LM only after you disable continual one-way LM or short-period one-way LM ends. If you have configured two-way LM, you can configure short-period one-way LM or continual one-way LM only after disable two-way LM.
To display the two-way LM result, use the display cfd dlm history command on the device where the source MEP or target MEP resides.
Two-way LM can be configured only in Layer 2 VPNs. MEPs created in a Layer 2 Ethernet service instance do not support two-way LM.
Examples
# Enable the continual two-way LM function to measure the frame loss between source MEP 1101 and target MEP 2001 in service instance 1.
<Sysname> system-view
[Sysname] cfd dlm continual service-instance 1 mep 1101 target-mep 2001
Related commands
cfd cc interval
cfd slm
cfd slm continual
display cfd dlm history
cfd dlm threshold
Use cfd dlm threshold to configure the lower limit and upper limit for continual two-way LM.
Use undo cfd dlm threshold to restore the default.
Syntax
cfd dlm { far-end | near-end } threshold service-instance instance-id mep mep-id { lower-limit lower-limit | upper-limit upper-limit } *
undo cfd dlm { far-end | near-end } threshold service-instance instance-id mep mep-id [ lower-limit | upper-limit ]
Default
The lower limit and upper limit for continual two-way LM are 0 and 100%, respectively, for both the source and target MEPs.
Views
System view
Predefined user roles
network-admin
Parameters
service-instance instance-id: Specifies a service instance by its ID in the range of 1 to 32767.
far-end: Configures the lower limit and upper limit for the target MEP.
near-end: Configures the lower limit and upper limit for the source MEP.
mep mep-id: Specifies a MEP by its ID in the range of 1 to 8191.
lower-limit lower-limit: Specifies the lower limit in percentage, in the range of 0 to 100. It can contain a maximum of 8 digits, including the dot (.), for example, 1.000001. The lower limit must be smaller than the upper limit.
upper-limit upper-limit: Specifies the upper limit in percentage, in the range of 0 to 100. It can contain a maximum of 8 digits, including the dot (.), for example, 1.000001.
Usage guidelines
This command takes effect only after you configure continual two-way LM.
When the packet loss ratio for the source MEP or target MEP reaches or exceeds the upper limit, the system displays a message about the situation.
When the packet loss ratios for both the source MEP and target MEP reach or fall below the lower limit, the system displays a message about the situation.
Examples
# Configure the lower limit and upper limit as 0.2% and 0.8%, respectively, for source MEP 1101 in service instance 1.
<Sysname> system-view
[Sysname] cfd dlm near-end threshold service-instance 1 mep 1101 lower-limit 0.2 upper-limit 0.8
Related commands
cfd dlm continual
display cfd dlm history
cfd dm two-way
Use cfd dm two-way to enable short-period two-way DM.
Syntax
cfd dm two-way service-instance instance-id mep mep-id { target-mac mac-address | target-mep target-mep-id } [ dot1p dot1p-value ] [ number number ] [ interval interval ]
Views
Any view
Predefined user roles
network-admin
Parameters
service-instance instance-id: Specifies a service instance by its ID in the range of 1 to 32767.
mep mep-id: Specifies the source MEP by its ID in the range of 1 to 8191.
target-mac mac-address: Specifies the target MEP by its bridge MAC address, which is in the format of H-H-H.
target-mep target-mep-id: Specifies the target MEP by its ID in the range of 1 to 8191.
dot1p dot1p-value: Specifies an 802.1p priority for DMMs. The value range for the dot1p-value argument is 0 to 7. The default value is 7.
number number: Specifies the number of DMM frames to be sent. The value range for the number argument is 2 to 10, and the default is 5.
interval interval: Specifies the DMM frame sending interval, in seconds. The value takes 1, 10, 60, or 600. The default value is 1.
Usage guidelines
The short-period two-way DM function measures the two-way frame delay between the source and target MEPs by using DMM frames and DMR frames.
To view the bridge MAC address of the target MEP, execute the display lacp system-id command on the target MEP.
Short-period two-way DM and continual two-way DM cannot be configured at the same time for one source MEP. If you have configured continual two-way DM, you can configure short-period two-way DM only after you disable continual two-way DM. If you have configured short-period two-way DM, you can configure continual two-way DM only after the short-period two-way DM ends.
Examples
# Enable the short-period two-way DM function to test the two-way frame delay between source MEP 1101 and target MEP 2001 in service instance 1.
<Sysname> cfd dm two-way service-instance 1 mep 1101 target-mep 2001
Frame delay:
Reply from 0010-fc00-6512: 10us
Reply from 0010-fc00-6512: 9us
Reply from 0010-fc00-6512: 11us
Reply from 0010-fc00-6512: 5us
Reply from 0010-fc00-6512: 5us
Average: 8us
Frame delay variation: 1us 2us 6us 0us
Average: 2us
Packet statistics:
Sent DMMs: 5 Received: 5 Lost: 0
Table 2 Command output
|
Field |
Description |
|
Reply from 0010-fc00-6512 |
Delay of the DMR frames returned from the MEP with MAC address 0010-FC00-6512. |
|
Average |
Average frame delay or average frame delay variation. |
|
Sent DMMs |
Number of sent DMM frames . |
|
Received |
Number of received DMR frames. |
|
Lost |
Number of lost DMM frames. |
Related commands
cfd dm two-way continual
cfd dm two-way continual
Use cfd dm two-way continual to enable continual two-way DM.
Use undo cfd dm two-way continual to disable continual two-way DM.
Syntax
cfd dm two-way continual service-instance instance-id mep mep-id { target-mac mac-address | target-mep target-mep-id } [ dot1p dot1p-value ] [ interval interval ]
undo cfd dm two-way continual service-instance instance-id mep mep-id
Default
Continual two-way DM is disabled.
Views
System view
Predefined user roles
network-admin
Parameters
service-instance instance-id: Specifies a service instance by its ID in the range of 1 to 32767.
mep mep-id: Specifies the source MEP by its ID in the range of 1 to 8191.
target-mac mac-address: Specifies the target MEP by its bridge MAC address, which is in the format of H-H-H.
target-mep target-mep-id: Specifies the target MEP by its ID in the range of 1 to 8191.
dot1p dot1p-value: Specifies an 802.1p priority for DMM frames. The value range for the dot1p-value argument is 0 to 7. The default value is 7.
interval interval: Specifies the DMM frame sending interval, in seconds. The value takes 1, 10, 60, or 600. The default value is 1.
Usage guidelines
Continual two-way DM continually sends DMM frames at a configurable interval. It measures the two-way frame delay between the source and target MEPs after receiving the returned DMR frames.
To view the bridge MAC address of the target MEP, execute the display lacp system-id command on the target MEP.
To modify continual two-way DM settings for a source MEP, disable continual two-way DM and then reconfigure the function for the source MEP.
Short-period two-way DM and continual two-way DM cannot be configured at the same time for one source MEP. If you have configured continual two-way DM, you can configure short-period two-way DM only after you disable continual two-way DM. If you have configured short-period two-way DM, you can configure continual two-way DM only after the short-period two-way DM ends.
To display the continual two-way DM result, use the display cfd dm two-way history command on the device where the source MEP resides.
Inward-facing MEPs created in an Ethernet network do not support continual two-way DM.
Examples
# Enable the continual two-way DM function to test the two-way frame delay between source MEP 1101 and target MEP 2001 in service instance 1.
<Sysname> system-view
[Sysname] cfd dm two-way continual service-instance 1 mep 1101 target-mep 2001
Related commands
cfd dm two-way
display cfd dm two-way history
cfd dm two-way threshold
Use cfd dm two-way threshold to configure the lower limit and upper limit for continual two-way DM.
Use undo cfd dm two-way threshold to restore the default.
Syntax
cfd dm two-way threshold service-instance instance-id mep mep-id { lower-limit lower-limit | upper-limit upper-limit } *
undo cfd dm two-way threshold service-instance instance-id mep mep-id [ lower-limit | upper-limit ]
Default
The lower limit and upper limit for continual two-way DM are 0 and 4294967295 microseconds, respectively.
Views
System view
Predefined user roles
network-admin
Parameters
service-instance instance-id: Specifies a service instance by its ID in the range of 1 to 32767.
mep mep-id: Specifies the source MEP by its ID in the range of 1 to 8191.
lower-limit lower-limit: Specifies the lower limit in the range of 0 to 4294967295 microseconds. The lower limit must be smaller than the upper limit.
upper-limit upper-limit: Specifies the upper limit in the range of 0 to 4294967295 microseconds.
Usage guidelines
This command takes effect only after you configure continual two-way DM.
If the delay time reaches or exceeds the upper limit for three consecutive times, the system displays a message about the situation.
If the delay time reaches or falls below the lower limit for three consecutive times, the system displays a message about the situation.
Examples
# Configure the continual two-way DM lower limit and upper limit as 10000 and 5000000 microseconds, respectively, for source MEP 1101 in service instance 1.
<Sysname> system-view
[Sysname] cfd dm two-way threshold service-instance 1 mep 1101 lower-limit 10000 upper-limit 5000000
Related commands
cfd dm two-way continual
display cfd dm two-way history
cfd enable
Use cfd enable to enable CFD.
Use undo cfd enable to disable CFD.
Syntax
cfd enable
undo cfd enable
Default
CFD is disabled.
Views
System view
Predefined user roles
network-admin
Examples
<Sysname> system-view
[Sysname] cfd enable
cfd frame-count mode
Use cfd frame-count mode to configure the frame counting mode for LM.
Use undo frame-count mode to restore the default.
Syntax
cfd frame-count mode { dot1p-based | port-based }
undo cfd frame-count mode
Default
No frame counting mode is configured for LM.
Views
Layer 3 Ethernet interface view
Layer 3 Ethernet subinterface view
Layer 3 aggregate interface view
Layer 3 aggregate subinterface view
Layer 2 Ethernet service instance view
Predefined user roles
network-admin
Parameters
dot1p-based: Counts packets by 802.1p priority.
port-based: Counts packets by interface.
Usage guidelines
To obtain accurate test results, configure the same frame counting mode on the source MEP and target MEP.
If the frame counting mode is dot1p-based, you must specify the dot1p dot1p-value option when configuring the cfd slm, cfd slm continual, and cfd dlm continual commands. If the frame counting mode is port-based, do not specify the dot1p dot1p-value option when configuring the cfd slm, cfd slm continual, and cfd dlm continual commands.
If LM has been configured for a MEP, the frame counting mode on the interface where the MEP resides cannot be modified.
This command can be configured only in MPLS Layer 2 VPNs.
Examples
# Configure the frame counting mode for LM as dot1p-based on HundredGigE 1/0/1.1.
<Sysname> system-view
[Sysname] interface hundredgige 1/0/1.1
[Sysname-HundredGigE1/0/1.1] cfd frame-count mode dot1p-based
Related commands
cfd dlm continual
cfd slm
cfd slm continual
cfd linktrace
Use cfd linktrace to identify the path between the source MEP and target MP.
Syntax
cfd linktrace service-instance instance-id mep mep-id { target-mac mac-address | target-mep target-mep-id } [ ttl ttl-value ] [ hw-only ]
Views
Any view
Predefined user roles
network-admin
Parameters
service-instance instance-id: Specifies a service instance by its ID in the range of 1 to 32767.
mep mep-id: Specifies the source MEP by its ID in the range of 1 to 8191.
target-mac mac-address: Specifies the target MEP by its bridge MAC address, in the format of H-H-H.
target-map target-mep-id: Specifies the destination MEP by its ID in the range of 1 to 8191.
ttl ttl-value: Specifies the TTL value in the range of 1 to 255. The default value is 64.
hw-only: Sets the hw-only bits of the LTMs sent. If you specify this keyword, the source MEP or the target MIP does not flood LTM messages that have an unknown destination MAC address.
Usage guidelines
This command identifies the path between the source MEP and target MP by using LTMs and LTRs.
To view the bridge MAC address of the target MEP, execute the display lacp system-id command on the target MEP.
Examples
# Identify the path between source MEP 1101 and target MEP 2001 in service instance 1.
<Sysname> cfd linktrace service-instance 1 mep 1101 target-mep 2001
Linktrace to MEP 2001 with the sequence number 1101-43361:
MAC address TTL Last MAC Relay action
0010-fc00-6512 63 0010-fc00-6500 Hit
Table 3 Command output
|
Field |
Description |
|
Linktrace to MEP 2001 with the sequence number 1101-43361 |
Linktrace to target MEP 2001 with the sequence number 1101-43361. |
|
MAC address |
Source MAC address in the LTR messages. |
|
TTL |
TTL of the LTM when it passes the device. |
|
Last MAC |
MAC address of the last-hop device the LTM passes. |
|
Relay action |
Indicates whether the forwarding device found the destination MAC address in its MAC address table. When the standard version (IEEE 802.1ag) of CFD is used: · Hit—The current device is the destination device. · FDB—The forwarding device found the destination MAC address. · MPDB—The destination MAC address is not found, or the destination MAC address is found in the MEP or MIP database. |
cfd linktrace auto-detection
display cfd linktrace-reply
cfd linktrace auto-detection
Use cfd linktrace auto-detection to enable automatic sending of LTMs.
Use undo cfd linktrace auto-detection to disable automatic sending of LTMs.
Syntax
cfd linktrace auto-detection [ size size-value ]
undo cfd linktrace auto-detection
Default
Automatic sending of LTMs is disabled.
Views
System view
Predefined user roles
network-admin
Parameters
size size-value: Specifies the size of the buffer used to store the auto-detection result, in the range of 1 to 100 (in terms of auto-detection times). The default value is 5, which means the buffer stores the results of the recent five auto-detections.
Usage guidelines
This command enables the source MEP to send LTMs when it fails to receive CCMs from the target MEP within 3.5 times the sending interval. The destination of the LTMs is the target MEP, and the TTL field value is 255. Based on the returned LTRs, the fault source can be located on the faulty link.
If you disable automatic LTM sending, the content stored in the buffer will be removed.
The outward-facing MEP on a hardware CC-supported card does not automatically send LTMs.
Examples
# Enable automatic LTM sending, and set the size of the buffer used to store the auto-detection result to 100 (in terms of auto-detection times).
<Sysname> system-view
[Sysname] cfd linktrace auto-detection size 100
cfd linktrace
display cfd linktrace-reply auto-detection
cfd loopback
Use cfd loopback to enable loopback (LB).
Syntax
cfd loopback service-instance instance-id mep mep-id { target-mac mac-address | target-mep target-mep-id } [ number number ]
Views
Any view
Predefined user roles
network-admin
Parameters
service-instance instance-id: Specifies a service instance by its ID in the range of 1 to 32767.
mep mep-id: Specifies the source MEP by its ID in the range of 1 to 8191.
target-mac mac-address: Specifies the target MEP by its bridge MAC address, in the format of H-H-H.
target-mep target-mep-id: Specifies the target MEP by its ID in the range of 1 to 8191.
number number: Specifies the number of the sent LBMs packets. The value is in the range of 1 to 10. The default value is 5.
Usage guidelines
The LB function verifies link connectivity between the source MEP and the target MP by using LBMs and LBRs.
To view the bridge MAC address of the target MEP, execute the display lacp system-id command on the target MEP.
Examples
# Enable LB for the link between MEP 1101 and MEP 2001 in service instance 1 (assume that the link status is normal).
<Sysname> cfd loopback service-instance 1 mep 1101 target-mep 2001
Loopback to MEP 2001 with the sequence number start from 1101-43404:
Reply from 0010-fc00-6512: sequence number=1101-43404 Time=5ms
Reply from 0010-fc00-6512: sequence number=1101-43405 Time=5ms
Reply from 0010-fc00-6512: sequence number=1101-43406 Time=5ms
Reply from 0010-fc00-6512: sequence number=1101-43407 Time=5ms
Reply from 0010-fc00-6512: sequence number=1101-43408 Time=5ms
Sent: 5 Received: 5 Lost: 0
# Enable LB for the link between MEP 1101 and MEP 2001 in service instance 1 (assume that the link status is abnormal).
<Sysname> cfd loopback service-instance 1 mep 1101 target-mep 2001
Loopback to MEP 2001 with the sequence number start from 1101-43404:
Sent: 5 Received: 0 Lost: 5
Table 4 Command output
|
Field |
Description |
|
Loopback to MEP 2001 with the sequence number start from 1101-43404 |
Sends LBMs to remote MEP 2001 with the sequence number starting with 1101-43404. |
|
Reply from 0010-fc00-6512 |
Reply from the MP with the MAC address 0010-FC00-6512. |
|
sequence number |
Sequence number in the LBR messages. |
|
Time=5ms |
The interval between the sending of LBMs and receiving of LBRs is 5 milliseconds. |
|
Sent |
Number of sent LBMs. |
|
Received |
Number of received LBRs. |
|
Lost |
Number of lost LBRs. |
cfd md
Use cfd md to create an MD.
Use undo cfd md to delete an MD.
Syntax
cfd md md-name [ index index-value ] level level-value [ md-id { dns dns-name | mac mac-address subnumber | none } ]
undo cfd md md-name
Default
No MDs exist.
Views
System view
Predefined user roles
network-admin
Parameters
md md-name: Specifies the name of an MD, which is a string of 1 to 43 characters that can contain letters, numbers, and special characters such as grave accent (`), tilde (~), exclamation mark (!), at sign (@), number sign (#), dollar sign ($), percent (%), caret (^), ampersand (&), asterisk (*), brackets ({ }, ( ),[ ], < >), hyphen (-), underscore (_), plus (+), equal sign (=), vertical bar (|), colon (:), semicolon (;), quotation mark ('), comma (,), period (.), and slash (/).
index index-value: Specifies an MD index in the range of 1 to 4294967295. If you do not specify this option, the system automatically assigns the smallest index number that is not in use. As a best practice, use the index automatically assigned by the system.
level level-value: Specifies an MD level in the range of 0 to 7.
md-id: Specifies the MD name carried by packets sent by the MEP. If you do not provide this keyword, the MD name is represented by md-name.
dns dns-name: Specifies an MD name in the format of DNS name, where dns-name represents the DNS name.
mac mac-address subnumber: Specifies an MD name containing the MAC address and an integer. The mac-address argument represents the MAC address of the MD, and the subnumber argument is in the range of 0 to 65535.
none: Specifies that no MD name is carried in the packets sent by the MEP.
Usage guidelines
An MD name must be in compliant with the specifications in IEEE802.1ag-2007.
You can create only one MD with a specific level. MD cannot be created if you enter an invalid MD name or an existing MD name or the MD index is in use.
When deleting an MD, you will also delete the configurations related to that MD.
Examples
# Create an MD named test_md1, with its level being 3.
<Sysname> system-view
[Sysname] cfd md test_md1 level 3
# Create an MD named test_md2, and the MD name carried in the packet sent by the MEP comprises the MAC address 1-1-1 and integer 1.
<Sysname> system-view
[Sysname] cfd md test_md2 level 5 md-id mac 1-1-1 1
cfd mep
Use cfd mep to create a MEP.
Use undo cfd mep to delete a MEP.
Syntax
In an Ethernet network:
· Layer 2 Ethernet interface view or Layer 2 aggregate interface view:
cfd mep mep-id service-instance instance-id { inbound | outbound }
undo cfd mep mep-id service-instance instance-id
· Layer 3 Ethernet interface view or Layer 3 Ethernet subinterface view:
cfd mep mep-id service-instance instance-id outbound
undo cfd mep mep-id service-instance instance-id
In a Layer 2 VPN:
· Layer 2 Ethernet service instance view, Layer 3 aggregate interface view, or Layer 3 aggregate subinterface view:
cfd mep mep-id service-instance instance-id inbound
undo cfd mep mep-id service-instance instance-id
· Layer 3 Ethernet interface view:
cfd mep mep-id service-instance instance-id { inbound | outbound }
undo cfd mep mep-id service-instance instance-id
· Layer 3 Ethernet subinterface view:
cfd mep mep-id service-instance instance-id inbound
cfd mep mep-id service-instance instance-id [ vlan vlan-id | service-vid vlan-id customer-vid vlan-id ] outbound
undo cfd mep mep-id service-instance instance-id
Default
No MEPs exist.
Views
Layer 2 Ethernet interface view
Layer 3 Ethernet interface view
Layer 2 aggregate interface view
Layer 3 Ethernet subinterface view
Layer 3 aggregate interface view
Layer 3 aggregate subinterface view
Layer 2 Ethernet service instance view
Predefined user roles
network-admin
Parameters
mep mep-id: Specifies the MEP ID, in the range of 1 to 8191.
service-instance instance-id: Specifies a service instance by its ID in the range of 1 to 32767.
vlan vlan-id: Specifies a VLAN by its ID in the range of 1 to 4094.
service-vid vlan-id: Specifies an outer VLAN (SVLAN) by its ID in the range of 1 to 4094.
customer-vid vlan-id: Specifies an inner VLAN (CVLAN) by its ID in the range of 1 to 4094.
inbound: Creates an inward-facing MEP.
outbound: Creates an outward-facing MEP.
Usage guidelines
In creating a MEP, the service instance you specified defines the MD and MA to which the MEP belongs.
You cannot create a MEP if the MEP ID is not included in the MEP list of the relevant service instance.
Follow these guidelines when you use the command:
· Configurations in Ethernet interface view or aggregate interface view take effect only on the current interface.
· If the MEP belongs to an MA that does not carry the VLAN attribute, configurations on a member port of an aggregate interface take effect only on the current member port.
· If the MEP belongs to an MA that carries the VLAN attribute, configurations on a member port of an aggregate interface take effect only when the member port leaves the aggregation group.
In an Ethernet network, you can create MEPs only on Layer 2 Ethernet interfaces, Layer 2 aggregate interfaces, Layer 3 Ethernet interfaces, and Layer 3 Ethernet subinterfaces.
In an MPLS Layer 2 VPN:
· For L2VPN networking, you can create MEPs only on Layer 3 Ethernet interfaces, Layer 3 Ethernet subinterfaces, Layer 3 aggregate interfaces, Layer 3 aggregate subinterfaces, and Layer 2 Ethernet service instances.
· For VPLS networking, you can create MEPs only on Layer 3 Ethernet interfaces, Layer 3 Ethernet subinterfaces, Layer 3 aggregate interfaces, and Layer 3 aggregate subinterfaces.
· Only one inward-facing MEP can be configured for a CFD service instance.
· A MEP can only be configured on an AC interface to detect PW connectivity.
To specify the VLAN ID when creating a MEP, you must first configure the vlan-type dot1q vid vlan-id-list command and specify the same value for the vlan-id-list and vlan vlan-id parameters. For more information about the vlan-type dot1q vid vlan-id-list command, see VLAN termination commands in Layer 2—LAN Switching Command Reference.
To specify the outer and inner VLAN IDs when creating a MEP, you must first configure the vlan-type dot1q vid second-dot1q command and set the same outer VLAN ID and the same inner VLAN ID in the two commands. For more information about the vlan-type dot1q vid second-dot1q command, see VLAN termination commands in Layer 2—LAN Switching Command Reference.
Examples
# In an Ethernet network, configure a MEP list in service instance 5, and create inward-facing MEP 3 in service instance 5 on HundredGigE 1/0/1.
<Sysname> system-view
[Sysname] cfd md test_md level 3
[Sysname] cfd service-instance 5 ma-id vlan-based md test_md vlan 100
[Sysname] cfd meplist 3 service-instance 5
[Sysname] interface hundredgige 1/0/1
[Sysname-HundredGigE1/0/1] cfd mep 3 service-instance 5 outbound
# In an MPLS Layer 2 VPN, configure a MEP list in service instance 5, and create inward-facing MEP 3 in service instance 5 on HundredGigE 1/0/1.1.
<Sysname> system-view
[Sysname] cfd md vpnmd level 4
[Sysname] cfd service-instance 5 ma-id string vpnma md vpnmd xconnect-group vpn1 connection ac2pw
[Sysname] cfd meplist 3 service-instance 5
[Sysname] interface hundredgige 1/0/1.1
[Sysname-HundredGigE1/0/1.1] cfd mep 3 service-instance 5 inbound
cfd meplist
vlan-type dot1q vid (Layer 2—LAN Switching Command Reference)
vlan-type dot1q vid second-dot1q (Layer 2—LAN Switching Command Reference)
cfd meplist
Use cfd meplist to create a MEP list.
Use undo cfd meplist to delete a MEP list.
Syntax
cfd meplist mep-list service-instance instance-id
undo cfd meplist mep-list service-instance instance-id
Default
No MEP list is created.
Views
System view
Predefined user roles
network-admin
Parameters
meplist mep-list: Specifies a space-separated list of up to 10 MEP items. Each item specifies a MEP ID or a range of MEP IDs in the form of mep-id 1 to mep-id 2. The value range for the MEP ID is 1 to 8191. The mep-id 2 must be equal to or greater than mep-id 1.
service-instance instance-id: Specifies a service instance by its ID in the range of 1 to 32767.
Usage guidelines
A MEP list is a collection of local MEPs allowed to be configured and the remote MEPs to be monitored in the same MA.
Before creating a MEP list, create the relevant MD and service instance.
After you delete a MEP list, all local MEP configurations based on this list are deleted.
Examples
# In an Ethernet network, create a MEP list that includes MEP 9 through MEP 15 in service instance 5.
<Sysname> system-view
[Sysname] cfd md test_md level 3
[Sysname] cfd service-instance 5 ma-id vlan-based md test_md vlan 100
[Sysname] cfd meplist 9 to 15 service-instance 5
# In an MPLS Layer 2 VPN, create a MEP list that includes MEP 9 through MEP 15 in service instance 5.
<Sysname> system-view
[Sysname] cfd md test_md level 3
[Sysname] cfd service-instance 5 ma-id string vpnma md vpnmd xconnect-group vpn1 connection ac2pw
[Sysname] cfd meplist 9 to 15 service-instance 5
Related commands
cfd md
cfd service-instance
cfd mip-rule
Use cfd mip-rule to configure the rules for generating MIPs.
Use undo cfd mip-rule to remove the rules for generating MIPs and the MIPs created in a service instance.
Syntax
cfd mip-rule { default | explicit } service-instance instance-id
undo cfd mip-rule [ default | explicit ] service-instance instance-id
Default
No rules for generating MIPs are configured and the system does not automatically generate any MIPs.
Views
System view
Predefined user roles
network-admin
Parameters
default: Specifies the default rule. If no lower-level MIP exists on an interface, a MIP is created on the current level. A MIP can be created even if no MEP is configured on the interface.
explicit: Specifies the explicit rule. If no lower-level MIP exists and a lower-level MEP exists on an interface, a MIP is created at the current level. A MIP can be created only when a lower-level MEP is created on the interface.
service-instance instance-id: Specifies a service instance by its ID in the range of 1 to 32767.
Usage guidelines
The system automatically generates MIPs on each interface according to the rules configured.
This command takes effect only in Ethernet networks.
Examples
# Configure the MIP generation rule as default in service instance 5.
<Sysname> system-view
[Sysname] cfd mip-rule default service-instance 5
cfd service-instance
Use cfd service-instance to create a service instance.
Use undo cfd service-instance to remove a service instance.
Syntax
In an Ethernet network:
cfd service-instance instance-id ma-id { icc-based ma-name | integer ma-num | string ma-name | vlan-based [ vlan-id ] } [ ma-index index-value ] md md-name vlan vlan-id
undo cfd service-instance instance-id
In an MPLS Layer 2 VPN:
cfd service-instance instance-id ma-id { icc-based ma-name | integer ma-num | string ma-name } [ ma-index index-value ] md md-name { xconnect-group group-name connection connection-name | vsi vsi-name }
undo cfd service-instance instance-id
Default
No service instances exist.
Views
System view
Predefined user roles
network-admin
Parameters
service-instance instance-id: Specifies the service instance ID in the range of 1 to 32767.
ma-id: Creates an MA.
icc-based ma-name: Specifies that an MA is identified by an ICC. The ma-name argument is a string of 1 to 13 characters. An MA name must be compliant with the specifications in IEEE802.1ag-2007
integer ma-num: Specifies that an MA is identified by an integer, where the ma-num argument is in the range of 0 to 65535.
string ma-name: Specifies that an MA is identified by a string, where the ma-name argument is string of 1 to 45 characters that can contain letters, numbers, and special characters such as grave accent (`), tilde (~), exclamation mark (!), at sign (@), number sign (#), dollar sign ($), percent (%), caret (^), ampersand (&), asterisk (*), brackets ({ }, ( ),[ ], < >), hyphen (-), underscore (_), plus (+), equal sign (=), vertical bar (|), colon (:), semicolon (;), quotation mark ('), comma (,), period (.), and slash (/).
vlan-based [ vlan-id ]: Specifies that an MA is identified by a VLAN ID, where the vlan-id argument is in the range of 1 to 4094. If you do not provide the vlan-id argument, the VLAN ID specified by vlan vlan-id is used. If the vlan vlan-id option is not provided, you must specify the vlan-id argument for the vlan-based [ vlan-id ] option.
ma-index index-value: Specifies an MA index in the range of 1 to 4294967295. If you do not specify this option, the system automatically assigns the smallest index number that is not in use. As a best practice, use the index automatically assigned by the system.
md md-name: Specifies the name of an MD. The md-name argument is a string of 1 to 43 characters that can contain letters, numbers, and special characters such as grave accent (`), tilde (~), exclamation mark (!), at sign (@), number sign (#), dollar sign ($), percent (%), caret (^), ampersand (&), asterisk (*), brackets ({ }, ( ),[ ], < >), hyphen (-), underscore (_), plus (+), equal sign (=), vertical bar (|), colon (:), semicolon (;), quotation mark (’), comma (,), period (.), and slash (/).
vlan vlan-id: Specifies the VLAN that the MA serves. The value range for the vlan-id argument is 1 to 4094.
xconnect-group group-name: Specifies the cross-connect group that the MA serves. The group-name argument is a case-sensitive string of 1 to 31 characters excluding hyphens (-).
connection connection-name: Specifies the cross-connect that the MA serves. The connection-name argument is a case-sensitive string of 1 to 20 characters excluding hyphens (-).
vsi vsi-name: Specifies the VSI that the MA serves. The vsi-name argument is a case-sensitive string of 1 to 31 characters.
Usage guidelines
You must create the relevant MD before creating a service instance.
Deleting a service instance also deletes the configurations related to that service instance.
Deleting a service instance not only removes the connection between the service instance and the relevant MA, but also deletes the MA.
When you create a service instance in an Ethernet network, follow these restrictions and guidelines:
· A service instance is indicated by an integer to represent an MA in an MD. An MA index uniquely identifies a specific MA in an MD. An MA index can be used in different MDs.
· With the vlan-based [ vlan-id ] or vlan vlan-id option, the command creates an MA carrying the VLAN attribute. If you do not specify the option, the command creates an MA carrying no VLAN attribute.
Examples
# Create a level-3 MD named test_md and create service instance 5, in which the MA is identified by a VLAN and serves VLAN 100.
<Sysname> system-view
[Sysname] cfd md test_md level 3
[Sysname] cfd service-instance 5 ma-id vlan-based md test_md vlan 100
# Create a level-4 MD named vpnmd and create service instance 10, in which the MA is identified by vpnma and serves cross-connect ac2pw in cross-connect group vpn1.
<Sysname> system-view
[Sysname] cfd md vpnmd level 4
[Sysname] cfd service-instance 10 ma-id string vpnma md vpnmd xconnect-group vpn1 connection ac2pw
Related commands
cfd md
display cfd dlm history
Use display cfd dlm history to display the two-way LM result.
Syntax
display cfd dlm history [ service-instance instance-id [ mep mep-id ] ] [ number number ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
service-instance instance-id: Specifies a service instance by its ID in the range of 1 to 32767. If you do not specify this option, the command displays the two-way LM results for all service instances.
mep mep-id: Specifies a MEP by its ID in the range of 1 to 8191. If you do not specify this option, the command displays the two-way LM results for all MEPs.
number number: Specifies the number of most recent two-way LM result entries to be displayed, in the range of 1 to 64. The default is 5.
Examples
# Display the two-way LM result for source MEP 1101 in service instance 1.
<Sysname> display cfd dlm history service-instance 1 mep 1101
Service instance: 1
MEP ID: 1101
Send status: Testing
Reply from 0010-fc00-6512:
Far-end frame loss : 1000 Far-end frame loss rate : 0.10%
Near-end frame loss: 2000 Near-end frame loss rate: 0.20%
Reply from 0010-fc00-6512:
Far-end frame loss : 4000 Far-end frame loss rate : 0.40%
Near-end frame loss: 4000 Near-end frame loss rate: 0.00%
Reply from 0010-fc00-6512:
Far-end frame loss : 0 Far-end frame loss rate : 0.00%
Near-end frame loss: 1000 Near-end frame loss rate: 0.10%
Reply from 0010-fc00-6512:
Far-end frame loss : 3000 Far-end frame loss rate : 0.30%
Near-end frame loss: 3000 Near-end frame loss rate: 0.30%
Reply from 0010-fc00-6512:
Far-end frame loss : 2000 Far-end frame loss rate : 0.20%
Near-end frame loss: 1 Near-end frame loss rate: <0.01%
Average
Far-end frame loss : 2000 Far-end frame loss rate : 0.20%
Near-end frame loss: 2500 Near-end frame loss rate: 0.25%
Table 5 Command output
|
Field |
Description |
|
Send status |
LM test status: · Testing—An LM test is in progress. · Init—An LM test is in initialization state and is about to start. · Stop—An LM test stopped. If an LM test has never been performed on a source MEP, this field displays a hyphen (-). |
|
Reply from 0010-fc00-6512 |
CCM frames returned from the target MEP with MAC address 0010-FC00-6512. |
|
Far-end frame loss |
Number of lost frames on the target MEP. |
|
Near-end frame loss |
Number of lost frames on the source MEP. |
|
Far-end frame loss rate |
Frame loss ratio on the target MEP. |
|
Near-end frame loss rate |
Frame loss ratio on the source MEP. |
|
Average |
Average number of lost frames. |
Related commands
cfd dlm continual
display cfd dm two-way history
Use display cfd dm two-way history to display the two-way DM result.
Syntax
display cfd dm two-way history [ service-instance instance-id [ mep mep-id ] ] [ number number ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
service-instance instance-id: Specifies a service instance by its ID in the range of 1 to 32767. If you do not specify this option, the command displays the two-way DM results for all service instances.
mep mep-id: Specifies a MEP by its ID in the range of 1 to 8191. If you do not specify this option, the command displays the two-way DM results for all MEPs.
number number: Specifies the number of most recent two-way DM result entries to be displayed, in the range of 1 to 64. The default is 5.
Examples
# Display the two-way DM results for all the MEPs in all service instances.
<Sysname> display cfd dm two-way history
Service instance: 1
MEP ID: 1003
Send status: Testing
Frame delay:
Reply from 0010-fc00-6512: 10us
Reply from 0010-fc00-6512: 9us
Reply from 0010-fc00-6512: 11us
Reply from 0010-fc00-6512: 5us
Reply from 0010-fc00-6512: 5us
Average: 8us
Frame delay variation: 1us 2us 6us 0us
Average: 2us
Packet statistics:
Sent DMMs: 5 Received: 5 Lost: 0
MEP ID: 1004
Send status: Init
Frame delay:
Reply from 0010-fc00-6512: 10us
Reply from 0010-fc00-6512: 9us
Reply from 0010-fc00-6512: 11us
Reply from 0010-fc00-6512: 5us
Reply from 0010-fc00-6512: 5us
Average: 8us
Frame delay variation: 1us 2us 6us 0us
Average: 2us
Packet statistics:
Sent DMMs: 5 Received: 5 Lost: 0
Service instance: 2
No MEP exists in the service instance.
Table 6 Command output
|
Field |
Description |
|
Send status |
DM test status: · Testing—A DM test is in progress. · Init—A DM test is in initialization state and is about to start. · Stop—A DM test stopped. If a DM test has never been performed on a source MEP, this field displays a hyphen (-). |
|
Reply from 0010-fc00-6512 |
Delay of DMR frames returned from the target MEP with MAC address 0010-FC00-6512. |
|
Average |
Average frame delay or average frame delay variation. |
|
Received |
Number of received DMR frames. |
|
Lost |
Number of lost DMR frames. |
Related commands
cfd dm two-way
cfd dm two-way continual
display cfd linktrace-reply
Use display cfd linktrace-reply to display the LTR information received by a MEP.
Syntax
display cfd linktrace-reply [ service-instance instance-id [ mep mep-id ] ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
service-instance instance-id: Specifies the service instance ID in the range of 1 to 32767. If you do not specify this option, the command displays the LTR information for all service instances.
mep mep-id: Specifies the ID of a MEP, in the range of 1 to 8191. If you do not specify this option, the command displays the LTR information for all MEPs.
Usage guidelines
This command displays only information about LTRs received by execution of the cfd linktrace command.
Examples
# Display the LTR information saved on all the MEPs in every service instance.
[Sysname] display cfd linktrace-reply
Service instance: 1 MEP ID: 1003
MAC address TTL Last MAC Relay action
0000-fc00-6505 63 0000-fc00-6504 MPDB
000f-e269-a852 62 0000-fc00-6505 FDB
0000-fc00-6508 61 000f-e269-a852 Hit
Service instance: 2 MEP ID: 1023
MAC address TTL Last MAC Relay action
0000-fc00-6508 61 000f-e269-a852 Hit
Table 7 Command output
|
Field |
Description |
|
Service instance |
Service instance to which the MEPs that send LTMs belong. |
|
MEP ID |
ID of the MEP that sends LTMs. |
|
MAC address |
Source MAC address in the LTR message. |
|
TTL |
TTL of the LTM when it passes the device. |
|
Last MAC |
MAC address of the last-hop device the LTM passes. |
|
Relay action |
Indicates whether the forwarding device found the destination MAC address in its MAC address table. When the standard version (IEEE 802.1ag) of CFD is used: · Hit—The current device is the destination device. · FDB—The forwarding device found the destination MAC address. · MPDB—The destination MAC address is not found, or the destination MAC address is found in the MEP or MIP database. |
Related commands
cfd linktrace
display cfd linktrace-reply auto-detection
Use display cfd linktrace-reply auto-detection to display information about the LTR messages received as responses to the automatically sent LTMs.
Syntax
display cfd linktrace-reply auto-detection [ size size-value ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
size size-value: Specifies the times of recent auto-detections, in the range of 1 to 100. If you do not specify this option, the command displays all information in the buffer.
Usage guidelines
This command displays only information about LTRs received by execution of the cfd linktrace auto-detection command.
Examples
# Display the contents of the LTRs received as responses to the LTMs automatically sent.
<Sysname> display cfd linktrace-reply auto-detection
Service instance: 1 MEP ID: 1003 Time: 2013/05/22 10:43:57
Target MEP ID: 2005 TTL: 64
MAC address TTL Last MAC Relay action
0000-fc00-6505 63 0000-fc00-6504 MPDB
000f-e269-a852 62 0000-fc00-6505 FDB
0000-fc00-6508 61 000f-e269-a852 Hit
Service instance: 2 MEP ID: 1023 Time: 2013/05/22 10:44:06
Target MEP ID: 2025 TTL: 64
MAC address TTL Last MAC Relay action
0000-fc00-6508 61 000f-e269-a852 Hit
Table 8 Command output
|
Field |
Description |
|
Service instance |
Service instance to which the MEPs that sent LTM messages belong. |
|
MEP ID |
ID of the MEP that sends LTMs. |
|
Time |
Time of the LTMs automatically sent. |
|
Target MEP ID |
ID of the target MEP. |
|
TTL |
Initial TTL of the automatically sent LTMs. |
|
MAC address |
Source MAC address in the LTR messages. |
|
TTL |
TTL of the LTM when it passes the device. |
|
Last MAC |
MAC address of the last-hop device the LTM passes. |
|
Relay action |
Indicates whether the forwarding device found the destination MAC address in its MAC address table. When the standard version (IEEE 802.1ag) of CFD is used: · Hit—The current device is the destination device. · FDB—The forwarding device found the destination MAC address. · MPDB—The destination MAC address is not found, or the destination MAC address is found in the MEP or MIP database. |
cfd linktrace auto-detection
display cfd md
Use display cfd md to display the MD configuration information.
Syntax
display cfd md
Views
Any view
Predefined user roles
network-admin
network-operator
Examples
# Display the MD configuration information.
<Sysname> display cfd md
CFD is enabled.
Maintenance domains configured: 4 in total
Level Index Maintenance domain MD format MD ID
0 1 md_0 CHARSTRING md_0
1 2 md_1 DNS dns1
2 3 md_2 MAC 0001-00
01-0001-1
3 4 md_3 NONE Without
ID
Table 9 Command output
|
Field |
Description |
|
Maintenance domains configured |
Number of MDs configured. |
|
Level |
Level of MD. |
|
Index |
MD index. |
|
Maintenance domain |
Name of MD. |
|
MD format |
MD name format: · CHARSTRING—Character string. · DNS—DNS name. · MAC—MAC address and an integer. · NONE—No MD name is carried. |
|
MD ID |
MD ID value: · A character string if the MD format is CHARSTRING. · A DNS name if the MD format is DNS. · A MAC address-subnumber if the MD format is MAC. · No ID if the MD format is NONE. |
display cfd mep
Use display cfd mep to display the attribute and operating information of a MEP.
Syntax
display cfd mep mep-id service-instance instance-id
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
mep mep-id: Specifies a MEP by its ID in the range of 1 to 8191.
service-instance instance-id: Specifies a service instance by its ID in the range of 1 to 32767.
Examples
# In an Ethernet network, display the attribute and operating information of MEP 50 in service instance 1.
<Sysname> display cfd mep 50 service-instance 1
Interface: HundredGigE1/0/2
Maintenance domain: md_0
Maintenance domain index: 1
Maintenance association: ma_0
Maintenance association index: 1
Level: 0 VLAN: 1 Direction: Outbound
Current state: Active CCM send: Enabled
FNG state: FNG_DEFECT_REPORTED
CCM:
Current state: CCI_WAITING
Interval: 1s SendCCM: 12018 ReceiveCCM: 24036
Loopback:
NextSeqNumber: 8877
SendLBR: 0 ReceiveInOrderLBR: 0 ReceiveOutOrderLBR: 0
SendLBM: 0 ReceiveLBM: 0
Linktrace:
NextSeqNumber: 8877
SendLTR: 0 ReceiveLTM: 0
SendLTM: 0 ReceiveLTR: 0
No CCM received from some remote MEPs.
One or more streams of error CCMs is received. The last received CCM:
Maintenance domain: (Without ID)
Maintenance association: matest1
MEP ID: 5 Sequence Number:0x50A
MAC Address: 0011-2233-4402
Received Time: 2013/03/06 13:01:34
One or more streams of cross-connect CCMs is received. The last received CCM:
Maintenance domain: mdtest1
Maintenance association:matest1
MEP ID: 6 Sequence Number:0x63A
MAC Address: 0011-2233-4401
Received Time: 2013/03/06 13:01:34
Some other MEPs are transmitting the RDI bit.
# In an MPLS Layer 2 VPN, display the attribute and operating information of MEP 50 in service instance 1.
<Sysname> display cfd mep 50 service-instance 1
Interface: HundredGigE1/0/2.1
Maintenance domain: md_0
Maintenance domain index: 1
Maintenance association: ma_0
Maintenance association index: 1
Level: 0 Direction: Inbound
Current state: Active CCM send: Enabled
FNG state: FNG_DEFECT_REPORTED
CCM:
Current state: CCI_WAITING
Interval: 1s SendCCM: 12018 ReceiveCCM: 24036
Loopback:
NextSeqNumber: 8877
SendLBR: 0 ReceiveInOrderLBR: 0 ReceiveOutOrderLBR: 0
SendLBM: 0 ReceiveLBM: 0
Linktrace:
NextSeqNumber: 8877
SendLTR: 0 ReceiveLTM: 0
SendLTM: 0 ReceiveLTR: 0
No CCM received from some remote MEPs.
Table 10 Command output
|
Field |
Description |
|
Interface |
Interface on which the MEP is configured. |
|
Maintenance domain |
MD to which the MEP belongs. (If the MD does not have a name, this field is displayed as Without ID.) |
|
Maintenance domain index |
Index of the MD to which the MEP belongs.. |
|
Maintenance association |
MA to which the MEP belongs. |
|
Maintenance association index |
Index of the MA to which the MEP belongs. |
|
Level |
Level of the MD. |
|
VLAN |
VLAN to which the MA belongs. |
|
EthSrv |
Ethernet service instance for the MEP. |
|
Direction |
Direction of the MEPs. |
|
Current state |
State of MEP: · Active. · Inactive. |
|
CCM send |
Whether the MEP sends CCM. |
|
FNG state |
State of FNG (Fault Notification Generator): · FNG_RESET—A fault has been cleared. · FNG_DEFECT—A fault has been detected. · FNG_REPORT_DEFECT—Report a fault. · FNG_DEFECT_REPORTED—A fault has been reported. · FNG_DEFECT_CLEARING—A fault is being cleared. If this field is not supported, a hyphen (-) is displayed. |
|
CCM |
Information related to CCM. |
|
Current state |
State of CCMs sent: · CCI_IDLE—Initial state. · CCI_WAITING—Sending state. If this field is not supported, a hyphen (-) is displayed. |
|
Interval |
Interval to send CCM. Not supported means the MEP does not support CCM sending. |
|
SendCCM |
Number of CCMs that have been sent by the MEPs. If this field is not supported, a hyphen (-) is displayed. |
|
ReceiveCCM |
Number of CCMs that have been received by the MEPs. If this field is not supported, a hyphen (-) is displayed. |
|
Loopback |
Information related to Loopback. |
|
NextSeqNumber |
Sequence number of the next LBM to be sent. |
|
SendLBR |
Number of LBRs that have been sent. If the MEP is inward-facing, the number of LBRs will not be counted. |
|
ReceiveInOrderLBR |
Number of LBR messages received in correct sequence. |
|
ReceiveOutOrderLBR |
Number of LBR messages received out of order. |
|
SendLBM |
Number of LBMs that have been sent. If the MEP is inward-facing, the number of LBMs will not be counted. |
|
ReceiveLBM |
Number of LBMs that have been received. |
|
Linktrace |
Information related to linktrace. |
|
NextSeqNumber |
Sequence number of the next LTM to be sent. |
|
SendLTR |
Number of LTRs sent. If the MEP is inward-facing, the number of LTRs will not be counted. |
|
ReceiveLTM |
Number of LTMs received. |
|
SendLTM |
Number of LTMs that have been sent. If the MEP is inward-facing, the number of LTMs will not be counted. |
|
ReceiveLTR |
Number of LTRs that have been received. |
|
No CCM received from some remote MEPs. |
Failure to receive CCMs from some remote MEPs. (This information is displayed only when some CCMs are lost.) |
|
One or more streams of error CCMs is received. The last received CCM: |
Display the content of the last error CCM when one or more error CCMs are received. (This information is displayed only when error CCMs are received.) |
|
Maintenance domain |
MD of the last error CCM message. If this field is not supported, a hyphen (-) is displayed. |
|
Maintenance association |
MA of the last error CCM message. If this field is not supported, a hyphen (-) is displayed. |
|
MEP |
ID of the MEP that sent the last error CCM message. If this field is not supported, a hyphen (-) is displayed. |
|
Sequence Number |
Sequence number of the last error CCM. If this field is not supported, a hyphen (-) is displayed. |
|
Received Time |
Time when the last error CCM is received. If this field is not supported, a hyphen (-) is displayed. |
|
One or more streams of cross-connect CCMs is received. The last received CCM: |
Cross-connect CCMs are received, and the content of the last cross-connect CCM is displayed. (This information is displayed only when cross-connect CCMs are received.) |
|
Some other MEPs are transmitting the RDI bit. |
CCMs with the RDI flag bits set are received from other MEPs. (This information is displayed only when this type of CCMs are received.) |
display cfd meplist
Use display cfd meplist to display the MEP list in a service instance.
Syntax
display cfd meplist [ service-instance instance-id ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
service-instance instance-id: Specifies a service instance by its ID in the range of 1 to 32767. If you do not specify this option, the command displays MEP lists in all service instances.
Examples
# Display the MEP list in service instance 5.
<Sysname> display cfd meplist service-instance 5
Service instance: 5
MEP list: 1 to 20, 30, 50.
display cfd mp
Use display cfd mp to display the MP information.
Syntax
display cfd mp [ interface interface-type interface-number ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify this option, the command displays MP information for all interfaces.
Usage guidelines
The output is arranged by interface name. On an interface, the output shows MPs that serve VLANs, and then shows MPs that do not serve any VLANs. The MPs that serve VLANs are displayed in the ascending VLAN ID order. Within the same VLAN, the output is in the order of MIPs and MEPs (from high to low level). The MEPs that do not serve any VLANs are displayed by level (from high to low).
Examples
# Display the MP information on all interfaces.
<Sysname> display cfd mp
Interface HundredGigE1/0/1 VLAN 100
MIP Level: 1 Service instance: 101
Maintenance domain: md_1
Maintenance domain index: 2
Maintenance association: ma_1
Maintenance association index: 2
MEP ID: 100 Level: 0 Service instance: 100 Direction: Outbound
Maintenance domain: md_0
Maintenance domain index: 1
Maintenance association: ma_0
Maintenance association index: 1
Interface HundredGigE1/0/2 VLAN NONE
MEP ID: 101 Level: 2 Service instance: 102 Direction: Inbound
Maintenance domain: md_2
Maintenance domain index: 3
Maintenance association: ma_2
Maintenance association index: 3
Table 11 Command output
|
Field |
Description |
|
Interface HundredGigE1/0/1 VLAN 100 |
MP configuration of VLAN 100 on HundredGigE 1/0/1. |
|
Interface HundredGigE1/0/2 VLAN NONE |
Configuration of the MP that does not serve any VLAN or configuration of the MP in an MPLS Layer 2 VPN. |
|
MIP |
A MIP in the MP. |
|
Level |
MD level to which the MP belongs. |
|
Service instance |
Service instance to which the MP belongs. |
|
Maintenance domain |
MD to which the MP belongs. |
|
Maintenance domain index |
Index of the MD to which the MP belongs. |
|
Maintenance association |
MA to which the MP belongs. |
|
Maintenance association index |
Index of the MA to which the MP belongs. |
|
Direction |
Direction of the MEP: · Inbound. · Outbound. |
display cfd remote-mep
Use display cfd remote-mep to display information about a remote MEP.
Syntax
display cfd remote-mep service-instance instance-id mep mep-id
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
service-instance instance-id: Specifies a service instance by its ID in the range of 1 to 32767.
mep mep-id: Specifies a MEP by its ID in the range of 1 to 8191.
Examples
# Display remote MEP information for MEP 10 in service instance 4.
<Sysname> display cfd remote-mep service-instance 4 mep 10
MEP ID MAC address State Time MAC status
20 00e0-fc00-6565 OK 2013/03/06 02:36:38 UP
30 00e0-fc27-6502 OK 2013/03/06 02:36:38 DOWN
40 00e0-fc00-6510 FAILED 2013/03/06 02:36:39 DOWN
50 00e0-fc52-baa0 OK 2013/03/06 02:36:44 DOWN
60 0010-fc00-6502 OK 2013/03/06 02:36:42 DOWN
Table 12 Command output
|
Field |
Description |
|
MEP ID |
ID of the remote MED. |
|
MAC address |
MAC address of the remote MEP device. If this field is not supported, a hyphen (-) is displayed. |
|
State |
Running state of the remote MEP: · OK. · FAILED. |
|
Time |
Time when the remote MEP entered the FAILED or OK state for the last time. If this field is not supported, a hyphen (-) is displayed. |
|
MAC status |
State of the interface indicated by the last CCM received from the remote MEP: · UP—The interface is ready to pass packets. · DOWN—The interface cannot pass packets. · TESTING—The interface is in some test mode. · UNKNOWN—The interface status cannot be determined. · DORMANT—The interface is not in a state to pass packets. Instead, it is in a pending state, waiting for some external event. · NOT-PRESENT—Some component of the interface is missing. · LLD—The interface is down due to state of the lower layer interfaces. If this field is not supported, a hyphen (-) is displayed. |
display cfd service-instance
Use display cfd service-instance to display the configuration information of service instances.
Syntax
display cfd service-instance [ instance-id ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
instance-id: Specifies a service instance ID in the range of 1 to 32767. If you do not specify this argument, the command displays configuration information for all service instances.
Examples
# In an Ethernet network, display the configuration information of all service instances.
<Sysname> display cfd service-instance
Service instances configured (2 in total):
Service instance 5:
Maintenance domain: md_5
Maintenance domain index: 5
Maintenance association: ma_5
Maintenance association index: 5
Level: 5 VLAN: 5 MIP rule: NONE CCM interval: 1s
Direction: Inbound
MEP ID: 730 Interface: HundredGigE1/0/1
Service instance 6:
Maintenance domain: (Without ID)
Maintenance domain index: 6
Maintenance association: ma_6
Maintenance association index: 6
Level: 6 VLAN: 6 MIP rule: NONE CCM interval: 1s
Direction: Outbound
MEP ID: 731 Interface: HundredGigE1/0/2
# In an MPLS Layer 2 VPN, display the configuration information of all service instances.
<Sysname> display cfd service-instance
Service instances configured (2 in total):
Service instance 5:
Maintenance domain: md_5
Maintenance domain index: 5
Maintenance association: ma_5
Maintenance association index: 5
Xconnect-group: vpn1
Xconnection: ldp1
Level: 5 MIP rule: NONE CCM interval: 1s
Direction: Inbound
MEP ID: 730 Interface: HundredGigE1/0/1
Service instance 6:
Maintenance domain: (Without ID)
Maintenance domain index: 6
Maintenance association: ma_6
Maintenance association index: 6
Xconnect-group: vpn2
Xconnection: ldp2
Level: 6 MIP rule: NONE CCM interval: 1s
Direction: Inbound
MEP ID: 731 Interface: HundredGigE1/0/2
Table 13 Command output
|
Field |
Description |
|
Service instances are configured. |
Number of service instances configured. |
|
Service instance |
Service instance ID. |
|
Maintenance domain |
MD of the service instance. (If the MD does not have a name, this field displays Without ID.) |
|
Maintenance domain index |
Index of the MD to which the service instance belong. |
|
Maintenance association: |
MA of the service instance. |
|
Maintenance association index |
Index of the MA to which the service instance belong. |
|
Xconnect-group |
Cross-connect group name. |
|
Xconnection |
Cross-connect name. |
|
Level |
MD level. |
|
VLAN |
VLAN to which the MA belongs. |
|
MIP rule |
MIP generation rules configured on the service instance. |
|
CCM interval |
Interval to send CCMs. |
|
Direction |
Direction of the MEPs configured on the service instance. |
|
MEP ID |
ID of MEPs configured on the service instance. |
|
Interface |
Interface of the MEP configured on the service instance. |
display cfd status
Use display cfd status to display the CFD status.
Syntax
display cfd status
Views
Any view
Predefined user roles
network-admin
network-operator
Examples
# Display the CFD status.
CFD is enabled.
AIS is disabled.
Table 14 Command output
|
Field |
Description |
|
AIS is enabled |
This field is not supported in the current software version. AIS is enabled. |
|
AIS is disabled |
This field is not supported in the current software version. AIS is disabled. |
