Login
- Table of Contents
-
- H3C S12500R-2L Switch Router Installation Guide-6W102
- 00-Preface
- 01-Chapter 1 Preparing for Installation
- 02-Chapter 2 Installing the Device
- 03-Chapter 3 Installing Removalbe Components
- 04-Chapter 4 Connecting Your Device to the Network
- 05-Chapter 5 Troubleshooting
- 06-Chapter 6 Replacement Procedures
- 07-Appendix A Chassis Views and Technical Specifications
- 08-Appendix B Removable Components and Compatibility Matrixes
- 09-Appendix C LEDs
- 10-Appendix D Cables
- Related Documents
-
| Title | Size | Download |
|---|---|---|
| 08-Appendix B Removable Components and Compatibility Matrixes | 124.45 KB |
Contents
1 Appendix B Removable components and compatibility matrixes
Chassis component ordering information
1 Appendix B Removable components and compatibility matrixes
For the transceiver modules and cables available for the modules, see H3C S12500R Switch Router Series Modules and Transceiver Modules Compatibility Matrixes.
SEUs
The device uses a supervisor engine unit (SEU, also called MPU) for system control and management. You can install one SEU, or two SEUs for redundancy on the device. Do not install SEUs of different models on the same device. The LSXM1SUP02LR1 SEU is available for the device.
Table1-1 LSXM1SUP02LR1 SEU specifications
|
Item |
Specification |
|
Processor |
Intel processor (Quad-Core) @ 2.2 GHz |
|
SDRAM |
16GB DDR4 SDRAM for one DIMM slot (two DIMM slots) |
|
Flash |
8 GB EMMC |
|
NVRAM |
512 KB |
|
Connector type |
· RJ-45 · LC · USB (Type A) |
|
Ports |
· 1 × console port · 1 × 10/100/1000BASE-T port for management and upgrade · 1 × GE SFP port for management and upgrade · 1 × USB port (USB2.0, host port) |
|
Transmission rate |
· Console port: 9600 bps (default) to 115200 bps · 10/100/1000BASE-T port: 10/100/1000 Mbps · SFP port: 1000 Mbps |
|
Cables and max transmission distance |
· Console port: 15 m (49.21 ft) over a common asynchronous serial interface cable · 10/100/1000BASE-T port: 100 m (328.08 ft) over category-5 twisted pairs |
|
|
IMPORTANT: · To verify compatibility of the module with the software release you are using, see the release notes. · The USB port outputs power as prescribed by USB 2.0. You can only install a USB 2.0-compliant device in the USB port. · Set the same speed and duplex mode for a management Ethernet port and its peer port. · To upgrade software or BootWare from the BootWare menu, you can only use the 10/100/1000BASE-T port (M0/0/1) rather than the GE SFP port (M0/0/0) for image file transferring. |
Interface modules
The LSXM1CGQ48KBR1 interface module is available for the device.
Table1-2 LSXM1CGQ48KBR1 interface module specification
|
Interface module |
Description |
Connector type |
Port number |
Transmission rate |
Available transceiver modules and cables |
|
LSXM1CGQ48KBR1 |
48-port 100GBASE Ethernet optical interface module (QSFP28) |
· MPO · LC |
48 |
100 Gbps |
· QSFP28 transceiver module · QSFP28 copper cable · QSFP28 fiber cable · QSFP+ transceiver module · QSFP+ copper cable · QSFP+ fiber cable |
Power supplies
|
|
CAUTION: You must install power supplies of the same model for the device. |
The device supports N+N (dual power input sources) or N+1 (single power input source) power supply redundancy. Determine the number of power supplies based on the power supply mode and system power consumption. Make sure the maximum total output power of the installed power supplies is greater than the system power consumption. Reserve a 20% power surplus as a best practice.
The PSR1800-56A and PSR1800-56D power supplies are available for the device.
Table1-3 PSR1800-56A power supply specifications
|
Item |
Specifications |
|
|
Rated input voltage |
100 to 240 VAC @ 50 or 60 Hz |
|
|
Rated output voltage |
56 VDC |
|
|
Maximum input current |
· 13 A @ 110 VAC · 9 A @ 220 VAC |
|
|
Maximum output current |
32.2 A |
|
|
Maximum output power |
· 1100 W @ 100 VAC to 200 VAC · 1800 W @ 201 VAC to 240 VAC · 1800 W @ 240 VDC |
|
|
Dimensions (H × W × D) |
40.1 × 82.6 × 297.7 mm (1.58 × 3.25 × 11.72 in) |
|
|
Ambient temperature |
Operating temperature |
–10°C to +50°C (–14°F to +122°F) |
|
Storage temperature |
–40°C to + 70°C (–40°F to +158°F) |
|
Table1-4 PSR1800-56D power supply specifications
|
Item |
Specifications |
|
|
Rated input voltage |
–48 to –60 VDC |
|
|
Rated output voltage |
56 VDC |
|
|
Maximum input current |
45 A |
|
|
Maximum output current |
32.2 A |
|
|
Maximum output power |
1800 W |
|
|
Dimensions (H × W × D) |
40.1 × 82.6 × 297.7 mm (1.58 × 3.25 × 11.72 in) |
|
|
Ambient temperature |
Operating temperature |
–10°C to +50°C (–14°F to +122°F) |
|
Storage temperature |
–40°C to + 70°C (–40°F to +158°F) |
|
|
|
NOTE: The power supply shuts down automatically when its temperature exceeds the acceptable range. When the temperature returns to the acceptable range, the power supply automatically restarts. |
Fan trays
The FAN-120-1-A fan tray is available for the device.
Table1-5 FAN-120-1-A fan tray specifications
|
Fan tray |
Number of fans |
Fan diameter |
Maximum airflow |
|
FAN-120-1-A |
2 |
120 mm (4.72 in) |
1240 CFM |
DC power cords
A DC power cord is used to connect a DC power supply on the device to an external DC power source.
Table1-6 describes DC power cords available for the device.
Table1-6 Specifications for the DC power cords
|
DC power cord BOM code |
Applicable power supplies |
Cable length |
Description |
|
0404A0RB |
PSR1800-56D |
3 m (9.84 ft) |
Connects the DC power supply to an external DC power source. |
|
0404A0RA |
15 m (49.21 ft) |
AC power cords
An AC power cord is used to connect an AC power supply on the device to an external AC power source. AC power cords include standard power cords and jumper power cords.
Selection of an AC power cord depends on the power supply (the current-carrying capacity of the power cord must meet the power supply requirement), power supply system in the equipment room, and connector and plug types in the country or region. Make sure you select a compliant power cord for a power supply.
For more information about AC power cords, see H3C Power Cords & Cables User Guide.
Chassis component ordering information
To purchase chassis components, contact the sales agent or H3C sales personnel.
Table1-7 Chassis component ordering information
|
Product code |
Product name |
Description |
|
SEUs |
||
|
0231ABV3 |
LSXM1SUP02LR1 |
H3C S12500R-2L supervisor engine unit |
|
Interface modules |
||
|
0231ABV2 |
LSXM1CGQ48KBR1 |
H3C S12500R 48-port 100GBASE Ethernet optical interface module (QSFP28) (KB) |
|
Fan tray |
||
|
0231ABVR |
LSXM102LFAN |
H3C S12500R-2L Ethernet switch router fan module |
|
Power supply |
||
|
0231A2KX |
LSVM3PSRA |
H3C port-to-power airflow 1800W AC power supply |
|
0231A2KY |
PSR1800-56D |
H3C port-to-power airflow 1800W DC power supply |
