Contents

MTR commands· 1

apply topology· 1

display mtr-policy· 1

display topology· 2

global-address-family ipv4· 3

if-match ip acl 4

if-match ip dscp· 5

if-match ip precedence· 6

mtr-policy· 7

routing-table limit 8

topology· 9

topology ipv4· 10

topology-routing mtr-policy· 11

 

MTR commands

apply topology

Use apply topology to specify a topology for the MTR policy node.

Use undo apply topology to remove the configuration.

Syntax

apply topology topo-name

undo apply topology

Default

No topology is specified for the MTR policy node.

Views

MTR policy node view

Predefined user roles

network-admin

Parameters

topo-name: Specifies a topology by its name, a case-sensitive string of 1 to 31 characters.

Examples

# Specify topology topo1 for node 0 of MTR policy mtr.

<Sysname> system-view

[Sysname] mtr-policy mtr node 0

[Sysname-mtr-policy-mtr-0] apply topology topo1

display mtr-policy

Use display mtr-policy to display MTR policy information.

Syntax

display mtr-policy [ name mtr-policy-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

name mtr-policy-name: Specifies an MTR policy by its name, a case-sensitive string of 1 to 63 characters. If you do not specify this option, the command displays information about all MTR policies.

Examples

# Display information about all MTR policies.

<Sysname> display mtr-policy

MTR-policy: mtr

  Node: 0

        if-match ip precedence critical

        if-match ip acl 3333

        apply topology 1

MTR-policy: p

  Node: 1

        if-match ip precedence routine

        if-match ip dscp cs1

        if-match ip acl 3501

MTR-policy: q

  Node: 0

        if-match ip precedence network

        if-match ip dscp ef

        if-match ip acl 3001

        apply topology 1

  Node: 1

MTR-policy: w

  Node: 0

        if-match ip precedence routine

        if-match ip dscp 3

Table 1 Command output

Field	Description
MTR-policy	MTR policy name.
Node	MTR policy node.

 

display topology

Use display topology to display topology information.

Syntax

display topology [ name topo-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

name topo-name: Specifies a topology by its name, a case-sensitive string of 1 to 31 characters. If you do not specify this option, the command displays brief information about all topologies.

Examples

# Display brief information about all topologies.

<Sysname> display topology

  Total topologies : 4

  Topology                        Address-family         VRF

  base                            IPv4                   default

  mt1                             IPv4                   default

  mt2                             IPv4                   default

  mt3                             IPv4                   default

# Display detailed information about topology mt1.

<Sysname> display topology name mt1

Topology Name and Index: mt1, 1

Address-family: IPv4

Interfaces: LoopBack0, GigabitEthernet1/0,

            GigabitEthernet2/0, GigabitEthernet3/0,

            GigabitEthernet4/0

Maximum routes limit : 100

Threshold value(%): 90

Table 2 Command output

Field	Description
Total topologies	Total number of topologies.
Topology	Topology name.
Address-family	Address family to which the topology belongs.
VRF	VPN to which the topology belongs.
Topology Name and Index	Topology name and index number.
Interfaces	Interface with which the topology is associated.
Maximum routes limit	Maximum number of route prefixes supported by the topology.
Threshold value(%)	Warning threshold for routes supported by the topology.

 

global-address-family ipv4

Use global-address-family ipv4 to create the global address family and enter its view.

Use undo global-address-family ipv4 to delete the global address family and all configurations in the view.

Syntax

global-address-family ipv4 [ unicast ]

undo global-address-family ipv4 [ unicast ]

Default

No global address family view exists.

Views

System view

Predefined user roles

network-admin

Parameters

unicast: Specifies the IPv4 unicast address family. If you do not specify this keyword, the command also specifies the IPv4 unicast address family.

Usage guidelines

Before you configure MTR, enter global address family view by using this command.

Examples

# Enter global address family view.

<Sysname> system-view

[Sysname] global-address-family ipv4 unicast

[Sysname-af]

if-match ip acl

Use if-match ip acl to configure an ACL match criterion.

Use undo if-match ip acl to restore the default.

Syntax

if-match ip acl acl-number

undo if-match ip acl

Default

No ACL match criterion is configured.

Views

MTR policy node view

Predefined user roles

network-admin

Parameters

acl-number: Specifies an advanced ACL by its number in the range of 3000 to 3999.

Usage guidelines

You can configure the ACL, DSCP, and IP precedence match criteria for an MTR node at the same time. The match criteria are in an OR relationship. If a packet matches one of the criteria, it matches the node, as well as the MTR policy. If a packet fails to match a node, it goes to the next node for a match.

Examples

# Configure an ACL match criterion for node 0 of MTR policy mtr, allowing packets matching ACL 3333 to pass.

<Sysname> system-view

[Sysname] mtr-policy mtr node 0

[Sysname-mtr-policy-mtr-0] if-match ip acl 3333

if-match ip dscp

Use if-match ip dscp to configure a DSCP match criterion.

Use undo if-match ip dscp to restore the default.

Syntax

if-match ip dscp dscp-value

undo if-match ip dscp

Default

No DSCP match criterion is configured.

Views

MTR policy node view

Predefined user roles

network-admin

Parameters

dscp-value: Specifies a DSCP value in the range of 0 to 63. You can also specify the DSCPs, as shown in Table 3, by description.

Table 3 Description of DSCP values

Description	DSCP value (binary)	DSCP value (decimal)
default	000000	0
af11	001010	10
af12	001100	12
af13	001110	14
af21	010010	18
af22	010100	20
af23	010110	22
af31	011010	26
af32	011100	28
af33	011110	30
af41	100010	34
af42	100100	36
af43	100110	38
cs1	001000	8
cs2	010000	16
cs3	011000	24
cs4	100000	32
cs5	101000	40
cs6	110000	48
cs7	111000	56
ef	101110	46

 

Usage guidelines

You can configure the ACL, DSCP, and IP precedence match criteria for an MTR node at the same time. The match criteria are in an OR relationship. If a packet matches one of the criteria, it matches the node, as well as the MTR policy. If a packet fails to match a node, it goes to the next node for a match.

Examples

# Configure a DSCP match criterion for node 0 of MTR policy mtr, allowing packets with a DSCP value of 5 to pass.

<Sysname> system-view

[Sysname] mtr-policy mtr node 0

[Sysname-mtr-policy-mtr-0] if-match ip dscp 5.

if-match ip precedence

Use if-match ip precedence to configure an IP precedence match criterion.

Use undo if-match ip precedence to restore the default.

Syntax

if-match ip precedence precedence

undo if-match ip precedence

Default

No IP precedence match criterion is configured.

Views

MTR policy node view

Predefined user roles

network-admin

Parameters

precedence: Specifies an IP precedence value in the range of 0 to 7. You can also specify an IP precedence by its description. For more information, see Table 4.

Table 4 Description of IP precedence

Description	IP precedence
routine	0
priority	1
immediate	2
flash	3
flash-override	4
critical	5
internet	6
network	7

 

Usage guidelines

You can configure the ACL, DSCP, and IP precedence match criteria for an MTR node at the same time. The match criteria are in an OR relationship. If a packet matches one of the criteria, it matches the node, as well as the MTR policy. If a packet fails to match a node, it goes to the next node for a match.

Examples

# Configure an IP precedence match criterion for node 0 of MTR policy mtr, allowing packets with an IP precedence of 5 to pass.

<Sysname> system-view

[Sysname] mtr-policy mtr node 0

[Sysname-mtr-policy-mtr-0] if-match ip precedence 5

mtr-policy

Use mtr-policy to create an MTR policy node and enter its view, or enter the view of an existing MTR policy node.

Use undo mtr-policy to delete the specified MTR policy node.

Syntax

mtr-policy policy-name node node-value

undo mtr-policy policy-name [ node node-value ]

Default

No MTR policy nodes exist.

Views

System view

Predefined user roles

network-admin

Parameters

policy-name: Specifies an MTR policy by its name, a case-sensitive string of 1 to 63 characters.

node node-value: Specifies an MTR policy node by its number in the range of 0 to 255.

Usage guidelines

An MTR policy comprises multiple nodes that are in an OR relationship. If a packet matches one of the nodes, it matches the MTR policy.

Use the undo mtr-policy policy-name node node-value command to delete the specified node from the specified MTR policy. If the MTR policy has only one node, the command also deletes the MTR policy.

Use the undo mtr-policy policy-name command to delete the specified MTR policy.

Examples

# Create MTR policy mtr and node 0, and enter MTR policy node view.

<Sysname> system-view

[Sysname] mtr-policy mtr node 0

[Sysname-mtr-policy-mtr-0]

routing-table limit

Use routing-table limit to configure the maximum number of active routes supported by the topology.

Use undo routing-table limit to restore the default.

Syntax

routing-table limit number { warn-threshold | simply-alert }

undo routing-table limit

Default

A topology supports a maximum of 100000 active routes.

Views

Topology view

Predefined user roles

network-admin

Parameters

number: Specifies the maximum number of active routes supported by the topology. The value range for this argument is 0 to 6000000.

warn-threshold: Specifies a warning threshold in the range of 1 to 100 in percentage. When the percentage of the number of existing active routes to the maximum number of active routes exceeds the specified threshold, the system generates an alarm message but still allows new active routes. If active routes in the topology reach the maximum, no more active routes are added.

simply-alert: Enables the topology to add new active routes but generate a system log message when the maximum number of active routes is exceeded.

Examples

# Configure the maximum number of active routes supported by topology mt1 as 1000. Enable the topology to add new active routes but generate a system log message when the maximum number of active routes is exceeded.

<Sysname> system-view

[Sysname] global-address-family ipv4 unicast

[Sysname-af] topology mt1

[Sysname-af-topology-mt1] routing-table limit 1000 simply-alert

topology

Use topology to create a topology and enter its view.

Use undo topology to remove a topology.

Syntax

topology topo-name

undo topology topo-name

Default

No topologies exist.

Views

Global address family view

Predefined user roles

network-admin

Parameters

topo-name: Specifies a topology by its name, a case-sensitive string of 1 to 31 characters.

Examples

# Create topology mt and enter its view.

<Sysname> system-view

[Sysname] global-address-family ipv4 unicast

[Sysname-af] topology mt

[Sysname-af-topology-mt]

topology ipv4

Use topology ipv4 to associate the interface with a topology and enter IPv4 unicast topology view of the interface.

Use undo topology ipv4 to remove the association between an IPv4 unicast topology and the interface.

Syntax

topology ipv4 [ unicast ] topo-name

undo topology ipv4 [ unicast ] topo-name

Default

An interface is not associated with any topologies.

Views

Interface view

Predefined user roles

network-admin

Parameters

unicast: Specifies the unicast topology. If you do not specify this keyword, the command also specifies the unicast topology.

topo-name: Specifies a topology by its name, a case-sensitive string of 1 to 31 characters.

Usage guidelines

Before you associate the interface with a topology, you must create the topology.

If the topology name is unicast, you must specify the unicast keyword for the command. Otherwise, the command cannot take effect.

Examples

# Associate interface Loopback 0 with topology mt1 and enter IPv4 unicast topology view of the interface.

<Sysname> system-view

[Sysname] interface loopback 0

[Sysname-LoopBack0] topology ipv4 unicast mt1

[Sysname-LoopBack0-topology-1]

topology-routing mtr-policy

Use topology-routing mtr-policy to enable an MTR policy.

Use undo topology-routing mtr-policy to disable the MTR policy.

Syntax

topology-routing mtr-policy policy-name

undo topology-routing mtr-policy

Default

An MTR policy is disabled.

Views

Global address family view

Predefined user roles

network-admin

Parameters

policy-name: Specifies an MTR policy by its name, a case-sensitive string of 1 to 63 characters.

Examples

# Enable MTR policy mtr.

<Sysname> system-view

[Sysname] global-address-family ipv4

[Sysname-global-ipv4] topology-routing mtr-policy mtr