05-Layer 3 - IP Services Command Reference

HomeSupportSwitchesS7500X SeriesReference GuidesCommand ReferencesH3C S7500X Switch Series Command References-Release758X-6W10005-Layer 3 - IP Services Command Reference
15-Tunneling commands
Title Size Download
15-Tunneling commands 103.57 KB

Tunneling commands

bandwidth

Use bandwidth to set the expected bandwidth for an interface.

Use undo bandwidth to restore the default.

Syntax

bandwidth bandwidth-value

undo bandwidth

Default

The expected bandwidth (in kbps) is the interface maximum rate divided by 1000.

Views

Tunnel interface view

Predefined user roles

network-admin

mdc-admin

Parameters

bandwidth-value: Specifies the expected bandwidth, in the range of 1 to 400000000 kbps.

Usage guidelines

The expected bandwidth for an interface affects the link costs in OSPF, OSPFv3, and IS-IS. For more information, see Layer 3—IP Routing Configuration Guide.

Examples

# Set the expected bandwidth for Tunnel 1 to 100 kbps.

<Sysname> system-view

[Sysname] interface tunnel 1

[Sysname-Tunnel1] bandwidth 100

default

Use default to restore the default settings for a tunnel interface.

Syntax

default

Views

Tunnel interface view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

CAUTION

CAUTION:

The default command might interrupt ongoing network services. Make sure you are fully aware of the impact of this command when you use it on a live network.

 

This command might fail to restore the default settings for some commands for reasons such as command dependencies or system restrictions. Use the display this command in interface view to identify these commands. Use their undo forms or follow the command reference to restore their default settings. If your restoration attempt still fails, follow the error message instructions to resolve the problem.

Examples

# Restore the default settings of Tunnel 1.

<Sysname> system-view

[Sysname] interface tunnel 1

[Sysname-Tunnel1] default

description

Use description to configure the description of an interface.

Use undo description to restore the default.

Syntax

description text

undo description

Default

The description of a tunnel interface is Tunnelnumber Interface, for example, Tunnel1 Interface.

Views

Tunnel interface view

Predefined user roles

network-admin

mdc-admin

Parameters

text: Specifies a description, a case-sensitive string of 1 to 255 characters.

Usage guidelines

Configure descriptions for different interfaces for identification and management purposes.

You can use the display interface command to display the configured interface description.

Examples

# Configure the description of Tunnel 1 as tunnel1.

<Sysname> system-view

[Sysname] interface tunnel 1

[Sysname-Tunnel1] description tunnel1

Related commands

display interface tunnel

destination

Use destination to specify the destination address for a tunnel interface.

Use undo destination to restore the default.

Syntax

destination { ipv4-address | ipv6-address | dhcp-alloc interface-type interface-number }

undo destination

Default

No tunnel destination address is configured.

Views

Tunnel interface view

Predefined user roles

network-admin

mdc-admin

Parameters

ipv4-address: Specifies the tunnel destination IPv4 address.

ipv6-address: Specifies the tunnel destination IPv6 address.

dhcp-alloc interface-type interface-number: Specifies an interface by its type and number to obtain AFTR's IPv6 address from DHCPv6 packets.

Usage guidelines

For a manual tunnel interface, you must configure the destination address. For an automatic tunnel interface, you do not need to configure the destination address.

The tunnel destination address must be the address of the receiving interface on the tunnel peer. It is used as the destination address of tunneled packets.

The destination address of the local tunnel interface must be the source address of the peer tunnel interface. The source address of the local tunnel interface must be the destination address of the peer tunnel interface.

Do not specify the same tunnel source and destination addresses for the tunnel interfaces on the same device.

Examples

# VLAN-interface 100 on Sysname 1 uses the IP address 193.101.1.1 and VLAN-interface 100 on Sysname 2 uses the IP address 192.100.1.1. Configure the source address 193.101.1.1 and destination address 192.100.1.1 for the tunnel interface on Sysname 1.

<Sysname1> system-view

[Sysname1] interface tunnel 1 mode ipv6-ipv4

[Sysname1-Tunnel1] source 193.101.1.1

[Sysname1-Tunnel1] destination 192.100.1.1

# Configure the source address 192.100.1.1 and destination address 193.101.1.1 for the tunnel interface on Sysname 2.

<Sysname2> system-view

[Sysname2] interface tunnel 1 mode ipv6-ipv4

[Sysname2-Tunnel1] source 192.100.1.1

[Sysname2-Tunnel1] destination 193.101.1.1

Related commands

display interface tunnel

interface tunnel

ipv6 address dhcp-alloc

source

display interface tunnel

Use display interface tunnel to display tunnel interface information.

Syntax

display interface [ tunnel [ number ] ] [ brief [ description | down ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

tunnel [ number ]: Specifies a tunnel interface. The number argument specifies the tunnel interface number. The specified tunnel interface must have been created. If you do not specify the tunnel keyword, this command displays information about all interfaces on the device. If you specify the tunnel keyword without the number argument, this command displays information about all existing tunnel interfaces.

brief: Displays brief interface information. If you do not specify this keyword, the command displays detailed interface information.

description: Displays complete interface descriptions. If you do not specify this keyword, the command displays only the first 27 characters of interface descriptions.

down: Displays information about interfaces in the physical state of DOWN and the causes. If you do not specify this keyword, the command displays information about interfaces in all states.

Examples

# Display detailed information about Tunnel 1.

<Sysname> display interface tunnel 1

Tunnel1

Current state: DOWN

Line protocol state: DOWN

Description: Tunnel1 Interface

Bandwidth: 64 kbps

Maximum transmission unit: 64000

Internet protocol processing: Disabled

Last clearing of counters: Never

Tunnel source unknown, destination unknown

Tunnel protocol/transport UDP_VXLAN/IP

Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Input: 0 packets, 0 bytes, 0 drops

Output: 0 packets, 0 bytes, 0 drops

Table 1 Command output

Field

Description

Tunnel1

Information about the tunnel interface Tunnel 1.

Current state

Physical link state of the tunnel interface:

·          Administratively DOWN—The interface has been shut down by using the shutdown command.

·          DOWN—The interface is administratively up, but its physical state is down (possibly because no physical link exists or the link has failed).

·          UP—The interface is both administratively and physically up.

Line protocol state

Data link layer state of the interface. The state is determined through automatic parameter negotiation at the data link layer.

·          UP—The data link layer protocol is up.

·          UP (spoofing)—The data link layer protocol is up, but the link is an on-demand link or does not exist. This attribute is typical of null interfaces and loopback interfaces.

·          DOWN—The data link layer protocol is down.

Description

Description of the tunnel interface.

Bandwidth

Expected bandwidth of the tunnel interface.

Maximum transmission unit

MTU of the tunnel interface.

Internet protocol processing: Disabled

The tunnel interface is not assigned an IP address and cannot process IP packets.

Internet address

IP address of the tunnel interface. The primary attribute indicates that the address is the primary IP address.

Tunnel source

Source address of the tunnel. If a source interface is specified for the tunnel interface, this field also displays the source interface in parentheses.

destination

Destination address of the tunnel.

Tunnel TOS

ToS of tunneled packets.

Tunnel TTL

TTL of tunneled packets.

Tunnel protocol/transport

Tunnel mode and transport protocol:

·          CR_LSP—MPLS TE tunnel mode.

·          GRE/IP—GRE/IPv4 tunnel mode.

·          GRE/IPv6—GRE/IPv6 tunnel mode.

·          GRE_EVI/IP—GRE-encapsulated IPv4 EVI tunnel mode.

·          IP/IP—IPv4 over IPv4 tunnel mode.

·          IP/IPv6—IPv4 over IPv6 tunnel mode.

·          IPv6—IPv6 tunnel mode.

·          IPv6/IP—IPv6 over IPv4 manual tunnel mode.

·          IPv6/IP 6to4—IPv6 over IPv4 6to4 tunnel mode.

·          IPv6/IP ISATAP—IPv6 over IPv4 ISATAP tunnel mode.

·          UDP_VXLAN/IP—UDP-encapsulated IPv4 VXLAN tunnel mode.

·          UDP_VXLAN_DCI/IP—UDP-encapsulated IPv4 VXLAN-DCI tunnel mode.

Last clearing of counters

Last time when counters were cleared.

Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Average input rate in the last 300 seconds.

Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Average output rate in the last 300 seconds.

Input: 0 packets, 0 bytes, 0 drops

Total input packets, total input bytes, and total input packets dropped.

Output: 0 packets, 0 bytes, 0 drops

Total output packets, total output bytes, and total output packets dropped.

 

# Display brief information about Tunnel 1.

<Sysname> display interface tunnel 1 brief

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface            Link Protocol Primary IP     Description

Tun1                 UP   UP       1.1.1.1        aaaaaaaaaaaaaaaaaaaaaaaaaaa

# Display brief information about Tunnel 1, including the complete interface description.

<Sysname> display interface tunnel 1 brief description

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface            Link Protocol Primary IP     Description

Tun1                 UP    UP      1.1.1.1        aaaaaaaaaaaaaaaaaaaaaaaaaaaaa

Aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa

# Display information about interfaces in DOWN state and the causes.

<Sysname> display interface tunnel brief down

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Interface            Link Cause

Tun0                  DOWN Not connected

Tun1                  DOWN Not connected

Table 2 Command output

Field

Description

Interface

Abbreviated interface name.

Link

Physical link state of the interface:

·          UP—The interface is physically up.

·          DOWN—The interface is physically down.

·          ADM—The interface has been shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command.

·          Stby—The interface is a backup interface in standby state. To see the primary interface, use the display interface-backup state command.

Protocol

Data link layer protocol state of the interface:

·          UP—The data link layer protocol of the interface is up.

·          DOWN—The data link layer protocol of the interface is down.

·          UP(s)—The data link layer protocol of the interface is up, but the link is an on-demand link or does not exist. The (s) attribute represents the spoofing flag. This value is typical of null interfaces and loopback interfaces.

Primary IP

Primary IP address of the interface. This field displays two hyphens (--) if the interface does not have an IP address.

Description

Description of the interface.

Cause

Cause for the physical link state of an interface to be DOWN:

·          Administratively—The interface has been manually shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command.

·          Not connected—The tunnel is not established.

 

Related commands

destination

interface tunnel

source

interface tunnel

Use interface tunnel to create a tunnel interface, specify the tunnel mode, and enter tunnel interface view, or enter the view of an existing tunnel interface.

Use undo interface tunnel to delete a tunnel interface.

Syntax

interface tunnel number [ mode { evi | gre [ ipv6 ] | ipv4-ipv4 | ipv6 | ipv6-ipv4 [ 6to4 | isatap ] | mpls-te | vxlan | vxlan-dci } ]

undo interface tunnel number

Default

No tunnel interfaces exist.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

number: Specifies the number of the tunnel interface. The value range is 1 to 4095.The number of tunnel interfaces that can be created is restricted by the total number of interfaces and the memory.

mode evi: Specifies the IPv4 EVI tunnel mode.

mode gre: Specifies the GRE/IPv4 tunnel mode.

mode gre ipv6: Specifies the GRE/IPv6 tunnel mode.

mode ipv4-ipv4: Specifies the IPv4 over IPv4 tunnel mode.

mode ipv6: Specifies the IPv6 tunnel mode. Set this mode for IPv4 over IPv6 manual and IPv6 over IPv6 tunnels.

mode ipv6-ipv4: Specifies the IPv6 over IPv4 manual tunnel mode.

mode ipv6-ipv4 6to4: Specifies the 6to4 tunnel mode.

mode ipv6-ipv4 isatap: Specifies the ISATAP tunnel mode.

mode mpls-te: Specifies the MPLS TE tunnel mode.

mode vxlan: Specifies the VXLAN tunnel mode.

mode vxlan-dci: Specifies the VXLAN-DCI tunnel mode.

Usage guidelines

To create a new tunnel interface, you must specify the tunnel mode in this command. To enter the view of an existing tunnel interface, you do not need to specify the tunnel mode.

A tunnel interface number is locally significant. The tunnel interfaces on the two ends of a tunnel can use the same or different interface numbers.

Examples

# Create GRE/IPv4 tunnel interface Tunnel 1 and enter tunnel interface view.

<Sysname> system-view

[Sysname] interface tunnel 1 mode gre

[Sysname-Tunnel1]

Related commands

destination

display interface tunnel

source

mtu

Use mtu to set the MTU on a tunnel interface.

Use undo mtu to restore the default.

Syntax

mtu size

undo mtu

Default

If the tunnel interface has never been up, the MTU is 64000 bytes.

If the tunnel interface is up, its MTU is identical to the outgoing interface's MTU minus the length of the tunnel headers. The outgoing interface is automatically obtained through routing table lookup based on the tunnel destination address.

Views

Tunnel interface view

Predefined user roles

network-admin

mdc-admin

Parameters

size: Specifies the MTU, in the range of 100 to 64000 bytes.

Usage guidelines

After you configure an MTU for a tunnel interface, the configured MTU applies regardless of the tunnel interface status (up/down) and the outgoing interface MTU.

To avoid fragmentation after tunnel encapsulation, set the tunnel interface MTU no greater than the value of the outgoing interface MTU minus the length of the tunnel headers.

Examples

# Set the MTU on Tunnel 1 to 10000 bytes.

<Sysname> system-view

[Sysname] interface tunnel 1

[Sysname-Tunnel1] mtu 10000

Related commands

display interface tunnel

reset counters interface tunnel

Use reset counters interface tunnel to clear tunnel interface statistics.

Syntax

reset counters interface [ tunnel [ number ] ]

Views

User view

Predefined user roles

network-admin

mdc-admin

Parameters

tunnel [ number ]: Specifies a tunnel interface. The number argument specifies the tunnel interface number. If you do not specify the tunnel keyword, this command clears statistics for all interfaces. If you specify the tunnel keyword without the number argument, this command clears statistics for all tunnel interfaces.

Usage guidelines

Use this command to clear old statistics so you can observe new traffic statistics on a tunnel interface.

Examples

# Clear statistics for Tunnel 1.

<Sysname> reset counters interface tunnel 1

Related commands

display interface tunnel

service

Use service to specify a traffic processing slot for a tunnel interface.

Use undo service to restore the default.

Syntax

In standalone mode:

service slot slot-number

undo service slot

In IRF mode:

service chassis chassis-number slot slot-number

undo service chassis

Default

No traffic processing slot is specified for a tunnel interface.

Views

Tunnel interface view

Predefined user roles

network-admin

mdc-admin

Parameters

slot slot-number: Specifies a card by its slot number. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. (In IRF mode.)

Usage guidelines

Specify a traffic processing slot if a feature (for example, IPsec antireplay) requires that all traffic on a tunnel interface be processed on the same slot.

Make sure the specified traffic processing slot is available. If the specified traffic processing slot is unavailable, traffic on the tunnel interface cannot be forwarded, whether or not the tunnel interface is up. Traffic on the tunnel interface will not be forwarded until the traffic processing slot becomes available or until you respecify an available traffic processing slot.

Examples

# Specify a traffic processing slot for Tunnel 200.

<Sysname> system-view

[Sysname] interface tunnel 200

[Sysname-Tunnel200] service slot 1

shutdown

Use shutdown to shut down a tunnel interface.

Use undo shutdown to bring up a tunnel interface.

Syntax

shutdown

undo shutdown

Default

A tunnel interface is not administratively down.

Views

Tunnel interface view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

This command disconnects all links set up on the interface. Make sure you fully understand the impact of the command on your network.

Examples

# Shut down Tunnel 1.

<Sysname> system-view

[Sysname] interface tunnel 1

[Sysname-Tunnel1] shutdown

Related commands

display interface tunnel

source

Use source to specify the source address or source interface for a tunnel interface.

Use undo source to restore the default.

Syntax

source { ipv4-address | ipv6-address | interface-type interface-number }

undo source

Default

No source address or source interface is specified for a tunnel interface.

Views

Tunnel interface view

Predefined user roles

network-admin

mdc-admin

Parameters

ipv4-address: Specifies the tunnel source IPv4 address.

ipv6-address: Specifies the tunnel source IPv6 address.

interface-type interface-number: Specifies the source interface by its type and number. The interface must be up and must have an IP address.

Usage guidelines

The specified source address or the address of the specified source interface is used as the source address of tunneled packets. To display the configured tunnel source address, use the display interface tunnel command.

Do not specify the same tunnel source and destination addresses for the tunnel interfaces on the same device.

The destination address of the local tunnel interface must be the source address of the peer tunnel interface. The source address of the local tunnel interface must be the destination address of the peer tunnel interface.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Specify VLAN-interface 10 as the source interface of Tunnel 1.

<Sysname> system-view

[Sysname] interface tunnel 1 mode gre

[Sysname-Tunnel1] source vlan-interface 10

# Specify 192.100.1.1 as the source address of Tunnel 1.

<Sysname> system-view

[Sysname] interface tunnel 1 mode gre

[Sysname-Tunnel1] source 192.100.1.1

Related commands

destination

display interface tunnel

interface tunnel

tunnel dfbit enable

Use tunnel dfbit enable to set the Don't Fragment (DF) bit for tunneled packets.

Use undo tunnel dfbit enable to restore the default.

Syntax

tunnel dfbit enable

undo tunnel dfbit enable

Default

The DF bit is not set for tunneled packets.

Views

Tunnel interface view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

To avoid fragmentation and delay, set the DF bit for tunneled packets. Make sure the path MTU is larger than the tunneled packet length. To avoid discarding tunneled packets whose length is larger than the path MTU, do not set the DF bit.

This command is not supported on GRE/IPv6 tunnel interfaces or IPv6 tunnel interfaces.

Examples

# Set the DF bit for tunneled packets on Tunnel 1.

<Sysname> system-view

[Sysname] interface tunnel 1 mode gre

[Sysname-Tunnel1] tunnel dfbit enable

tunnel discard ipv4-compatible-packet

Use tunnel discard ipv4-compatible-packet to enable dropping IPv6 packets that use IPv4-compatible IPv6 addresses.

Use undo tunnel discard ipv4-compatible-packet to restore the default.

Syntax

tunnel discard ipv4-compatible-packet

undo tunnel discard ipv4-compatible-packet

Default

IPv6 packets that use IPv4-compatible IPv6 addresses are not dropped.

Views

System view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

This command enables the device to check the source and destination IPv6 addresses of the de-encapsulated IPv6 packets from a tunnel. If a packet uses an IPv4-compatible IPv6 address as the source or destination address, the device discards the packet.

Examples

# Enable dropping IPv6 packets that use IPv4-compatible IPv6 addresses.

<Sysname> system-view

[Sysname] tunnel discard ipv4-compatible-packet

tunnel tos

Use tunnel tos to set the ToS of tunneled packets.

Use undo tunnel tos to restore the default.

Syntax

tunnel tos tos-value

undo tunnel tos

Default

The ToS of tunneled packets is the same as the ToS of the original packets.

Views

Tunnel interface view

Predefined user roles

network-admin

mdc-admin

Parameters

tos-value: Specifies the ToS of tunneled packets, in the range of 0 to 255.

Usage guidelines

After you configure this command, all the tunneled packets of different services sent on the tunnel interface will use the same configured ToS. For more information about ToS, see ACL and QoS Configuration Guide.

Examples

# Set the ToS of tunneled packets to 20 on Tunnel 1.

<Sysname> system-view

[Sysname] interface tunnel 1 mode gre

[Sysname-Tunnel1] tunnel tos 20

Related commands

display interface tunnel

tunnel ttl

Use tunnel ttl to set the Time to Live (TTL) of tunneled packets.

Use undo tunnel ttl to restore the default.

Syntax

tunnel ttl ttl-value

undo tunnel ttl

Default

The TTL of tunneled packets is 255.

Views

Tunnel interface view

Predefined user roles

network-admin

mdc-admin

Parameters

ttl-value: Specifies the TTL of tunneled packets, in the range of 1 to 255.

Usage guidelines

The TTL determines the maximum number of hops that the tunneled packets can pass. When the TTL expires, the tunneled packets are discarded to avoid loops.

Examples

# Set the TTL of tunneled packets to 100 on Tunnel 1.

<Sysname> system-view

[Sysname] interface tunnel 1 mode gre

[Sysname-Tunnel1] tunnel ttl 100

Related commands

display interface tunnel

tunnel vpn-instance

Use tunnel vpn-instance to specify a VPN instance for the destination address of a tunnel interface.

Use undo tunnel vpn-instance to restore the default.

Syntax

tunnel vpn-instance vpn-instance-name

undo tunnel vpn-instance

Default

The destination address of a tunnel interface belongs to the public network.

Views

Tunnel interface view

Predefined user roles

network-admin

mdc-admin

Parameters

vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters.

Usage guidelines

After this command is executed, the device looks up the routing table of the specified VPN instance to forward tunneled packets on the tunnel interface.

For a tunnel interface to come up, the tunnel source and destination must belong to the same VPN instance. To specify a VPN instance for the tunnel source, use the ip binding vpn-instance command on the tunnel source interface.

Examples

# Specify VPN instance vpn10 for the tunnel destination on Tunnel 1.

<Sysname> system-view

[Sysname] ip vpn-instance vpn10

[Sysname-vpn-instance-vpn10] route-distinguisher 1:1

[Sysname-vpn-instance-vpn10] vpn-target 1:1

[Sysname-vpn-instance-vpn10] quit

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] ip binding vpn-instance vpn10

[Sysname-Vlan-interface10] ip address 1.1.1.1 24

[Sysname-Vlan-interface10] quit

[Sysname] interface tunnel 1 mode gre

[Sysname-Tunnel1] source vlan-interface 10

[Sysname-Tunnel1] destination 1.1.1.2

[Sysname-Tunnel1] tunnel vpn-instance vpn10

Related commands

ip binding vpn-instance (MPLS Command Reference)

 

  • Cloud & AI
  • InterConnect
  • Intelligent Computing
  • Security
  • SMB Products
  • Intelligent Terminal Products
  • Product Support Services
  • Technical Service Solutions
All Services
  • Resource Center
  • Policy
  • Online Help
All Support
  • Become a Partner
  • Partner Resources
  • Partner Business Management
All Partners
  • Profile
  • News & Events
  • Online Exhibition Center
  • Contact Us
All About Us
新华三官网