During RADIUS authentication, the device uses a NAS-ID to set the NAS-Identifier attribute of RADIUS packets so that the RADIUS server can identify the access location of users.

The device selects the NAS-ID for the NAS-Identifier attribute in the following order:

1. NAS-ID bound with VLANs in a NAS-ID profile.

2. NAS-ID in an ISP domain.

By default, the device uses the device name as the NAS-ID.

Examples

# Create a NAS-ID profile named aaa and enter its view.

<Sysname> system-view

[Sysname] aaa nas-id profile aaa

[Sysname-nas-id-prof-aaa]

Related commands

nas-id

nas-id bind vlan

portal nas-id-profile

aaa session-id mode

Use aaa session-id mode to specify the format for attribute Acct-Session-Id.

Use undo aaa session-id mode to restore the default.

Syntax

aaa session-id mode { common | simplified }

undo session-id mode

Default

The device uses the common mode for attribute Acct-Session-Id.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

common: Specifies the common format for attribute Acct-Session-Id. In this format, the Acct-Session-Id attribute is a string with a minimum length of 38 characters. This string contains the prefix (indicating the access type), date and time, sequence number, LIP address of the access node, device ID, and job ID of the access process.

simplified: Specifies the simple format for attribute Acct-Session-Id. In this format, the Acct-Session-Id attribute is a string of 16 characters. This string contains the prefix (indicating the access type), month, sequence number, device ID, and LIP address of the access node.

Usage guidelines

Configure the format for attribute Acct-Session-Id to meet the requirements of the RADIUS servers.

Examples

# Specify the simple format for attribute Acct-Session-Id.

<Sysname> system-view

[Sysname] aaa session-id mode simplified

aaa session-limit

Use aaa session-limit to set the maximum number of concurrent users that can log on to the device through the specified method.

Use undo aaa session-limit to restore the default maximum number of concurrent users for the specified login method.

Syntax

In non-FIPS mode:

aaa session-limit { ftp | http | https | ssh | telnet } max-sessions

undo aaa session-limit { ftp | http | https | ssh | telnet }

In FIPS mode:

aaa session-limit { https | ssh } max-sessions

undo aaa session-limit { https | ssh }

Default

The maximum number of concurrent users is 32 for each user type.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

ftp: FTP users.

http: HTTP users.

https: HTTPS users.

ssh: SSH users.

telnet: Telnet users.

max-sessions: Specifies the maximum number of concurrent login users. The value range is 1 to 32 for SSH and Telnet services, and is 1 to 64 for FTP, HTTP, and HTTPS services.

Usage guidelines

After the maximum number of concurrent login users for a user type exceeds the upper limit, the system denies the subsequent users of this type.

Examples

# Set the maximum number of concurrent FTP users to 4.

<Sysname> system-view

[Sysname] aaa session-limit ftp 4

accounting advpn

Use accounting advpn to specify accounting methods for ADVPN users.

Use undo accounting advpn to restore the default.

Syntax

In non-FIPS mode:

accounting advpn { local [ radius-scheme radius-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ local ] [ none ] }

undo accounting advpn

In FIPS mode:

accounting advpn { local | radius-scheme radius-scheme-name } *

undo accounting advpn

Default

The default accounting methods of the ISP domain are used for ADVPN users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

local: Performs local accounting.

none: Does not perform accounting.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

You can specify one primary accounting method and multiple backup accounting methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the accounting advpn radius-scheme radius-scheme-name local none command specifies a primary RADIUS accounting method and two backup methods (local accounting and no accounting). The device performs RADIUS accounting by default and performs local accounting when the RADIUS server is invalid. The device does not perform accounting when both of the previous methods are invalid.

When the primary accounting method is local, the following rules apply to the accounting of a user:

· The device uses the backup accounting methods in sequence only if local accounting is invalid for one of the following reasons:

¡ An exception occurs in the local accounting process.

¡ The user account is not configured on the device or the user is not allowed to use the ADVPN service.

· The device does not turn to the backup accounting methods if local accounting is invalid because of any other reason. Accounting fails for the user.

Examples

# In ISP domain test, perform local accounting for ADVPN users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting advpn local

# In ISP domain test, perform RADIUS accounting for ADVPN users based on scheme rd and use local accounting as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting advpn radius-scheme rd local

Related commands

accounting default

local-user

radius scheme

accounting command

Use accounting command to specify the command line accounting method.

Use undo accounting command to restore the default.

Syntax

accounting command hwtacacs-scheme hwtacacs-scheme-name

undo accounting command

Default

The default accounting methods of the ISP domain are used for command line accounting.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

hwtacacs-scheme hwtacacs-scheme-name: Specifies an HWTACACS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

The command line accounting feature works with the accounting server to record valid commands that have been successfully executed on the device.

· When the command line authorization feature is disabled, the accounting server records all valid commands that have been successfully executed.

· When the command line authorization feature is enabled, the accounting server records only authorized commands that have been successfully executed.

Command line accounting can use only a remote HWTACACS server.

Examples

# In ISP domain test, perform command line accounting based on HWTACACS scheme hwtac.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting command hwtacacs-scheme hwtac

Related commands

accounting default

command accounting (Fundamentals Command Reference)

hwtacacs scheme

accounting default

Use accounting default to specify default accounting methods for an ISP domain.

Use undo accounting default to restore the default.

Syntax

In non-FIPS mode:

accounting default { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] [ none ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * [ none ] | none | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] [ none ] }

undo accounting default

In FIPS mode:

accounting default { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] }

undo accounting default

Default

The default accounting method of an ISP domain is local.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

hwtacacs-scheme hwtacacs-scheme-name: Specifies an HWTACACS scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local accounting.

none: Does not perform accounting.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

The default accounting method is used for all users that support this method and do not have an accounting method configured.

Local accounting is only used for monitoring and controlling the number of local user connections. It does not provide the statistics function that the accounting feature generally provides.

You can specify one primary default accounting method and multiple backup default accounting methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the accounting default radius-scheme radius-scheme-name local none command specifies the primary default RADIUS accounting method and two backup methods (local accounting and no accounting). The device performs RADIUS accounting by default and performs local accounting when the RADIUS server is invalid. The device does not perform accounting when both of the previous methods are invalid.

When the primary accounting method is local, the following rules apply to the accounting of a user:

· The device uses the backup accounting methods in sequence only if local accounting is invalid for one of the following reasons:

¡ An exception occurs in the local accounting process.

¡ The user account is not configured on the device or the user is not allowed to use the access service.

· The device does not turn to the backup accounting methods if local accounting is invalid because of any other reason. Accounting fails for the user.

Examples

# In ISP domain test, use RADIUS scheme rd as the primary default accounting method and use local accounting as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting default radius-scheme rd local

Related commands

hwtacacs scheme

local-user

radius scheme

accounting lan-access

Use accounting lan-access to specify accounting methods for LAN users.

Use undo accounting lan-access to restore the default.

Syntax

In non-FIPS mode:

accounting lan-access { broadcast radius-scheme radius-scheme-name1 radius-scheme radius-scheme-name2 [ local ] [ none ] | local [ radius-scheme radius-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ local ] [ none ] }

undo accounting lan-access

In FIPS mode:

accounting lan-access { broadcast radius-scheme radius-scheme-name1 radius-scheme radius-scheme-name2 [ local ] | local [ radius-scheme radius-scheme-name ] | radius-scheme radius-scheme-name [ local ] }

undo accounting lan-access

Default

The default accounting methods of the ISP domain are used for LAN users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

broadcast: Broadcasts accounting requests to servers in RADIUS schemes.

radius-scheme radius-scheme-name1: Specifies the primary broadcast RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

radius-scheme radius-scheme-name2: Specifies the backup broadcast RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local accounting.

none: Does not perform accounting.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

You can specify one primary accounting method and multiple backup accounting methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the accounting lan-access radius-scheme radius-scheme-name local none command specifies a primary RADIUS accounting method and two backup methods (local accounting and no accounting). The device performs RADIUS accounting by default and performs local accounting when the RADIUS server is invalid. The device does not perform accounting when both of the previous methods are invalid.

The following guidelines apply to broadcast accounting:

· The device sends accounting requests to the primary accounting servers in the specified broadcast RADIUS schemes at the real-time accounting interval set in the primary broadcast RADIUS scheme. If the primary server is unavailable in a scheme, the device sends accounting requests to the secondary servers of the scheme in the order the servers are configured.

· The accounting result is determined by the primary broadcast RADIUS scheme. The accounting result from the backup scheme is used as reference only. If the primary scheme does not return any result, the device considers the accounting as a failure.

When the primary accounting method is local, the following rules apply to the accounting of a user:

· The device uses the backup accounting methods in sequence only if local accounting is invalid for one of the following reasons:

¡ An exception occurs in the local accounting process.

¡ The user account is not configured on the device or the user is not allowed to use the LAN access service.

· The device does not turn to the backup accounting methods if local accounting is invalid because of any other reason. Accounting fails for the user.

Examples

# In ISP domain test, perform local accounting for LAN users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting lan-access local

# In ISP domain test, perform RADIUS accounting for LAN users based on scheme rd and use local accounting as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting lan-access radius-scheme rd local

# In ISP domain test, broadcast accounting requests of LAN users to RADIUS servers in schemes rd1 and rd2, and use local accounting as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting lan-access broadcast radius-scheme rd1 radius-scheme rd2 local

Related commands

accounting default

local-user

radius scheme

timer realtime-accounting

accounting login

Use accounting login to specify accounting methods for login users.

Use undo accounting login to restore the default.

Syntax

In non-FIPS mode:

accounting login { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] [ none ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * [ none ] | none | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] [ none ] }

undo accounting login

In FIPS mode:

accounting login { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] }

undo accounting login

Default

The default accounting methods of the ISP domain are used for login users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

hwtacacs-scheme hwtacacs-scheme-name: Specifies an HWTACACS scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local accounting.

none: Does not perform accounting.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

Accounting is not supported for FTP, SFTP, and SCP users.

You can specify one primary accounting method and multiple backup accounting methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the accounting login radius-scheme radius-scheme-name local none command specifies a primary default RADIUS accounting method and two backup methods (local accounting and no accounting). The device performs RADIUS accounting by default and performs local accounting when the RADIUS server is invalid. The device does not perform accounting when both of the previous methods are invalid.

When the primary accounting method is local, the following rules apply to the accounting of a user:

· The device uses the backup accounting methods in sequence only if local accounting is invalid for one of the following reasons:

¡ An exception occurs in the local accounting process.

¡ The user account is not configured on the device.

· The device does not turn to the backup accounting methods if local accounting is invalid because of any other reason. Accounting fails for the user.

Examples

# In ISP domain test, perform local accounting for login users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting login local

# In ISP domain test, perform RADIUS accounting for login users based on scheme rd and use local accounting as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting login radius-scheme rd local

Related commands

accounting default

hwtacacs scheme

local-user

radius scheme

accounting portal

Use accounting portal to specify accounting methods for portal users.

Use undo accounting portal to restore the default.

Syntax

In non-FIPS mode:

accounting portal { broadcast radius-scheme radius-scheme-name1 radius-scheme radius-scheme-name2 [ local ] [ none ] | local [ radius-scheme radius-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ local ] [ none ] }

undo accounting portal

In FIPS mode:

accounting portal { broadcast radius-scheme radius-scheme-name1 radius-scheme radius-scheme-name2 [ local ] | local [ radius-scheme radius-scheme-name ] | radius-scheme radius-scheme-name [ local ] }

undo accounting portal

Default

The default accounting methods of the ISP domain are used for portal users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

broadcast: Broadcasts accounting requests to servers in RADIUS schemes.

radius-scheme radius-scheme-name1: Specifies the primary broadcast RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

radius-scheme radius-scheme-name2: Specifies the backup broadcast RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local accounting.

none: Does not perform accounting.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

You can specify one primary accounting method and multiple backup accounting methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the accounting portal radius-scheme radius-scheme-name local none command specifies a primary default RADIUS accounting method and two backup methods (local accounting and no accounting). The device performs RADIUS accounting by default and performs local accounting when the RADIUS server is invalid. The device does not perform accounting when both of the previous methods are invalid.

The following guidelines apply to broadcast accounting:

When the primary accounting method is local, the following rules apply to the accounting of a user:

· The device uses the backup accounting methods in sequence only if local accounting is invalid for one of the following reasons:

¡ An exception occurs in the local accounting process.

¡ The user account is not configured on the device or the user is not allowed to use the portal service.

· The device does not turn to the backup accounting methods if local accounting is invalid because of any other reason. Accounting fails for the user.

Examples

# In ISP domain test, perform local accounting for portal users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting portal local

# In ISP domain test, perform RADIUS accounting for portal users based on scheme rd and use local accounting as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting portal radius-scheme rd local

# In ISP domain test, broadcast accounting requests of portal users to RADIUS servers in schemes rd1 and rd2, and use local accounting as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting portal broadcast radius-scheme rd1 radius-scheme rd2 local

Related commands

accounting default

local-user

radius scheme

timer realtime-accounting

accounting ppp

Use accounting ppp to specify accounting methods for PPP users.

Use undo accounting ppp to restore the default.

Syntax

In non-FIPS mode:

accounting ppp { broadcast radius-scheme radius-scheme-name1 radius-scheme radius-scheme-name2 [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] [ none ] | hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] [ none ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * [ none ] | none | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] [ none ] }

undo accounting ppp

In FIPS mode:

accounting ppp { broadcast radius-scheme radius-scheme-name1 radius-scheme radius-scheme-name2 [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] | hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] }

undo accounting ppp

Default

The default accounting methods of the ISP domain are used for PPP users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

broadcast: Broadcasts accounting requests to servers in RADIUS schemes.

radius-scheme radius-scheme-name1: Specifies the primary broadcast RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

radius-scheme radius-scheme-name2: Specifies the backup broadcast RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

hwtacacs-scheme hwtacacs-scheme-name: Specifies an HWTACACS scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local accounting.

none: Does not perform accounting.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

You can specify one primary accounting method and multiple backup accounting methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the accounting ppp radius-scheme radius-scheme-name local none command specifies a primary RADIUS accounting method and two backup methods (local accounting and no accounting). The device performs RADIUS accounting by default and performs local accounting when the RADIUS server is invalid. The device does not perform accounting when both of the previous methods are invalid.

The following guidelines apply to broadcast accounting:

· The device sends accounting requests to the primary accounting servers in the specified broadcast RADIUS schemes at the real-time accounting interval set in the primary broadcast RADIUS scheme. If the primary server is unavailable for a scheme, the device sends accounting requests to the secondary servers of the scheme in the order the servers are configured.

When the primary accounting method is local, the following rules apply to the accounting of a user:

· The device uses the backup accounting methods in sequence only if local accounting is invalid for one of the following reasons:

¡ An exception occurs in the local accounting process.

¡ The user account is not configured on the device or the user is not allowed to use the PPP service.

· The device does not turn to the backup accounting methods if local accounting is invalid because of any other reason. Accounting fails for the user.

Examples

# In ISP domain test, perform local accounting for PPP users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting ppp local

# In ISP domain test, perform RADIUS accounting for PPP users based on scheme rd and use local accounting as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting ppp radius-scheme rd local

# In ISP domain test, broadcast accounting requests of PPP users to RADIUS servers in schemes rd1 and rd2, and use local accounting as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting ppp broadcast radius-scheme rd1 radius-scheme rd2 local

Related commands

accounting default

hwtacacs scheme

local-user

radius scheme

timer realtime-accounting

accounting quota-out

Use accounting quota-out to configure access control for users that have used up their data or time accounting quotas.

Use undo accounting quota-out to restore the default.

Syntax

accounting quota-out { offline | online }

undo accounting quota-out

Default

The device logs off users that have used up their accounting quotas.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

offline: Logs off users that have used up their accounting quotas.

online: Allows users that have used up their accounting quotas to stay online.

Examples

# In ISP domain test, configure the device to allow users that have used up their accounting quotas to stay online.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting quota-out online

accounting sslvpn

Use accounting sslvpn to specify accounting methods for SSL VPN users.

Use undo accounting sslvpn to restore the default.

Syntax

In non-FIPS mode:

accounting sslvpn { local [ radius-scheme radius-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ local ] [ none ] }

undo accounting sslvpn

In FIPS mode:

accounting sslvpn { local | radius-scheme radius-scheme-name } *

undo accounting sslvpn

Default

The default accounting methods of the ISP domain are used for SSL VPN users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

local: Performs local accounting.

none: Does not perform accounting.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

You can specify one primary accounting method and multiple backup accounting methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the accounting sslvpn radius-scheme radius-scheme-name local none command specifies a primary RADIUS accounting method and two backup methods (local accounting and no accounting). The device performs RADIUS accounting by default and performs local accounting when the RADIUS server is invalid. The device does not perform accounting when both of the previous methods are invalid.

When the primary accounting method is local, the following rules apply to the accounting of a user:

· The device uses the backup accounting methods in sequence only if local accounting is invalid for one of the following reasons:

¡ An exception occurs in the local accounting process.

¡ The user account is not configured on the device or the user is not allowed to use the SSL VPN service.

· The device does not turn to the backup accounting methods if local accounting is invalid because of any other reason. Accounting fails for the user.

Examples

# In ISP domain test, perform local accounting for SSL VPN users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting sslvpn local

# In ISP domain test, perform RADIUS accounting for SSL VPN users based on scheme rd and use local accounting as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting sslvpn radius-scheme rd local

Related commands

accounting default

local-user

radius scheme

accounting start-fail

Use accounting start-fail to configure access control for users that encounter accounting-start failures.

Use undo accounting start-fail to restore the default.

Syntax

accounting start-fail { offline | online }

undo accounting start-fail

Default

The device allows users that encounter accounting-start failures to stay online.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

offline: Logs off users that encounter accounting-start failures.

online: Allows users that encounter accounting-start failures to stay online.

Examples

# In ISP domain test, configure the device to allow users that encounter accounting-start failures to stay online.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting start-fail online

accounting update-fail

Use accounting update-fail to configure access control for users that have failed all their accounting-update attempts.

Use undo accounting update-fail to restore the default.

Syntax

accounting update-fail { [ max-times max-times ] offline | online }

undo accounting update-fail

Default

The device allows users that have failed all their accounting-update attempts to stay online.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

max-times max-times: Specifies the maximum number of consecutive accounting-update failures allowed by the device for each user. The value range for the times argument is 1 to 255, and the default value is 1.

offline: Logs off users that have failed all their accounting-update attempts.

online: Allows users that have failed all their accounting-update attempts to stay online.

Examples

# In ISP domain test, configure the device to allow users that have failed all their accounting-update attempts to stay online.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] accounting update-fail online

authentication advpn

Use authentication advpn to specify authentication methods for ADVPN users.

Use undo authentication advpn to restore the default.

Syntax

In non-FIPS mode:

authentication advpn { local [ radius-scheme radius-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ local ] [ none ] }

undo authentication advpn

In FIPS mode:

authentication advpn { local | radius-scheme radius-scheme-name } *

undo authentication advpn

Default

The default authentication methods of the ISP domain are used for ADVPN users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

local: Performs local authentication.

none: Does not perform authentication.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

You can specify one primary authentication method and multiple backup authentication methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the authentication advpn radius-scheme radius-scheme-name local none command specifies a primary RADIUS authentication method and two backup methods (local authentication and no authentication). The device performs RADIUS authentication by default and performs local authentication when the RADIUS server is invalid. The device does not perform authentication when both of the previous methods are invalid.

When the primary authentication method is local, the following rules apply to the authentication of a user:

· The device uses the backup authentication methods in sequence only if local authentication is invalid for one of the following reasons:

¡ An exception occurs in the local authentication process.

¡ The user account is not configured on the device or the user is not allowed to use the ADVPN service.

· The device does not turn to the backup authentication methods if local authentication is invalid because of any other reason. Authentication fails for the user.

Examples

# In ISP domain test, perform local authentication for ADVPN users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authentication advpn local

# In ISP domain test, perform RADIUS authentication for ADVPN users based on scheme rd and use local authentication as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authentication advpn radius-scheme rd local

Related commands

authentication default

local-user

radius scheme

authentication default

Use authentication default to specify default authentication methods for an ISP domain.

Use undo authentication default to restore the default.

Syntax

In non-FIPS mode:

authentication default { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] [ none ] | ldap-scheme ldap-scheme-name [ local ] [ none ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * [ none ] | local [ ldap-scheme ldap-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] [ none ] }

undo authentication default

In FIPS mode:

authentication default { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] | ldap-scheme ldap-scheme-name [ local ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * | local [ ldap-scheme ldap-scheme-name ] | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] }

undo authentication default

Default

The default authentication method of an ISP domain is local.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

hwtacacs-scheme hwtacacs-scheme-name: Specifies an HWTACACS scheme by its name, a case-insensitive string of 1 to 32 characters.

ldap-scheme ldap-scheme-name: Specifies an LDAP scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local authentication.

none: Does not perform authentication.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

The default authentication method is used for all users that support this method and do not have an authentication method configured.

You can specify one primary default authentication method and multiple backup default authentication methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the authentication default radius-scheme radius-scheme-name local none command specifies a primary default RADIUS authentication method and two backup methods (local authentication and no authentication). The device performs RADIUS authentication by default and performs local authentication when the RADIUS server is invalid. The device does not perform authentication when both of the previous methods are invalid.

When the primary authentication method is local, the following rules apply to the authentication of a user:

· The device uses the backup authentication methods in sequence only if local authentication is invalid for one of the following reasons:

¡ An exception occurs in the local authentication process.

¡ The user account is not configured on the device or the user is not allowed to use the access service.

· The device does not turn to the backup authentication methods if local authentication is invalid because of any other reason. Authentication fails for the user.

Examples

# In ISP domain test, use RADIUS scheme rd as the primary default authentication method and use local authentication as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authentication default radius-scheme rd local

Related commands

hwtacacs scheme

ldap scheme

local-user

radius scheme

authentication ike

Use authentication ike to specify extended authentication methods for IKE users.

Use undo authentication ike to restore the default.

Syntax

In non-FIPS mode:

authentication ike { local [ radius-scheme radius-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ local ] [ none ] }

undo authentication ike

In FIPS mode:

authentication ike { local | radius-scheme radius-scheme-name } *

undo authentication ike

Default

The default authentication methods of the ISP domain are used for IKE extended authentication.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

local: Performs local authentication.

none: Does not perform authentication.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

You can specify one primary authentication method and multiple backup authentication methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the authentication ike radius-scheme radius-scheme-name local none command specifies a primary RADIUS authentication method and two backup methods (local authentication and no authentication). The device performs RADIUS authentication by default and performs local authentication when the RADIUS server is invalid. The device does not perform authentication when both of the previous methods are invalid.

When the primary authentication method is local, the following rules apply to the authentication of a user:

· The device uses the backup authentication methods in sequence only if local authentication is invalid for one of the following reasons:

¡ An exception occurs in the local authentication process.

¡ The user account is not configured on the device or the user is not allowed to use the IKE service.

· The device does not turn to the backup authentication methods if local authentication is invalid because of any other reason. Authentication fails for the user.

Examples

# In ISP domain test, configure the device to perform local authentication through IKE extended authentication.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authentication ike local

# In ISP domain test, perform IKE extended authentication based on RADIUS scheme rd and use local authentication as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authentication ike radius-scheme rd local

Related commands

authentication default

local-user

radius scheme

authentication lan-access

Use authentication lan-access to specify authentication methods for LAN users.

Use undo authentication lan-access to restore the default.

Syntax

In non-FIPS mode:

authentication lan-access { ldap-scheme ldap-scheme-name [ local ] [ none ] | local [ ldap-scheme ldap-scheme-name | radius-scheme radius-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ local ] [ none ] }

undo authentication lan-access

In FIPS mode:

authentication lan-access { ldap-scheme ldap-scheme-name [ local ] | local [ ldap-scheme ldap-scheme-name | radius-scheme radius-scheme-name ] | radius-scheme radius-scheme-name [ local ] }

undo authentication lan-access

Default

The default authentication methods of the ISP domain are used for LAN users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

ldap-scheme ldap-scheme-name: Specifies an LDAP scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local authentication.

none: Does not perform authentication.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

You can specify one primary authentication method and multiple backup authentication methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the authentication lan-access radius-scheme radius-scheme-name local none command specifies a primary RADIUS authentication method and two backup methods (local authentication and no authentication). The device performs RADIUS authentication by default and performs local authentication when the RADIUS server is invalid. The device does not perform authentication when both of the previous methods are invalid.

When the primary authentication method is local, the following rules apply to the authentication of a user:

· The device uses the backup authentication methods in sequence only if local authentication is invalid for one of the following reasons:

¡ An exception occurs in the local authentication process.

¡ The user account is not configured on the device or the user is not allowed to use the LAN access service.

· The device does not turn to the backup authentication methods if local authentication is invalid because of any other reason. Authentication fails for the user.

Examples

# In ISP domain test, perform local authentication for LAN users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authentication lan-access local

# In ISP domain test, perform RADIUS authentication for LAN users based on scheme rd and use local authentication as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authentication lan-access radius-scheme rd local

Related commands

authentication default

hwtacacs scheme

ldap scheme

local-user

radius scheme

authentication login

Use authentication login to specify authentication methods for login users.

Use undo authentication login to restore the default.

Syntax

In non-FIPS mode:

authentication login { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] [ none ] | ldap-scheme ldap-scheme-name [ local ] [ none ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * [ none ] | local [ ldap-scheme ldap-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] [ none ] }

undo authentication login

In FIPS mode:

authentication login { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] | ldap-scheme ldap-scheme-name [ local ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * | local [ ldap-scheme ldap-scheme-name ] | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] }

undo authentication login

Default

The default authentication methods of the ISP domain are used for login users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

hwtacacs-scheme hwtacacs-scheme-name: Specifies an HWTACACS scheme by its name, a case-insensitive string of 1 to 32 characters.

ldap-scheme ldap-scheme-name: Specifies an LDAP scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local authentication.

none: Does not perform authentication.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

You can specify one primary authentication method and multiple backup authentication methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the authentication login radius-scheme radius-scheme-name local none command specifies the default primary RADIUS authentication method and two backup methods (local authentication and no authentication). The device performs RADIUS authentication by default and performs local authentication when the RADIUS server is invalid. The device does not perform authentication when both of the previous methods are invalid.

When the primary authentication method is local, the following rules apply to the authentication of a user:

· The device uses the backup authentication methods in sequence only if local authentication is invalid for one of the following reasons:

¡ An exception occurs in the local authentication process.

¡ The user account is not configured on the device or the user is not allowed to use the service for accessing the device.

· The device does not turn to the backup authentication methods if local authentication is invalid because of any other reason. Authentication fails for the user.

Examples

# In ISP domain test, perform local authentication for login users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authentication login local

# In ISP domain test, perform RADIUS authentication for login users based on scheme rd and use local authentication as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authentication login radius-scheme rd local

Related commands

authentication default

hwtacacs scheme

ldap scheme

local-user

radius scheme

authentication portal

Use authentication portal to specify authentication methods for portal users.

Use undo authentication portal to restore the default.

Syntax

In non-FIPS mode:

authentication portal { ldap-scheme ldap-scheme-name [ local ] [ none ] | local [ ldap-scheme ldap-scheme-name | radius-scheme radius-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ local ] [ none ] }

undo authentication portal

In FIPS mode:

authentication portal { ldap-scheme ldap-scheme-name [ local ] | local [ ldap-scheme ldap-scheme-name | radius-scheme radius-scheme-name ] | radius-scheme radius-scheme-name [ local ] }

undo authentication portal

Default

The default authentication methods of the ISP domain are used for portal users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

ldap-scheme ldap-scheme-name: Specifies an LDAP scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local authentication.

none: Does not perform authentication.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

You can specify one primary authentication method and multiple backup authentication methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the authentication portal radius-scheme radius-scheme-name local none command specifies the default primary RADIUS authentication method and two backup methods (local authentication and no authentication). The device performs RADIUS authentication by default and performs local authentication when the RADIUS server is invalid. The device does not perform authentication when both of the previous methods are invalid.

When the primary authentication method is local, the following rules apply to the authentication of a user:

· The device uses the backup authentication methods in sequence only if local authentication is invalid for one of the following reasons:

¡ An exception occurs in the local authentication process.

¡ The user account is not configured on the device or the user is not allowed to use the portal service.

· The device does not turn to the backup authentication methods if local authentication is invalid because of any other reason. Authentication fails for the user.

Examples

# In ISP domain test, perform local authentication for portal users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authentication portal local

# In ISP domain test, perform RADIUS authentication for portal users based on scheme rd and use local authentication as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authentication portal radius-scheme rd local

Related commands

authentication default

ldap scheme

local-user

radius scheme

authentication ppp

Use authentication ppp to specify authentication methods for PPP users.

Use undo authentication ppp to restore the default.

Syntax

In non-FIPS mode:

authentication ppp { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] [ none ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * [ none ] | none | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] [ none ] }

undo authentication ppp

In FIPS mode:

authentication ppp { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] }

undo authentication ppp

Default

The default authentication methods of the ISP domain are used for PPP users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

hwtacacs-scheme hwtacacs-scheme-name: Specifies an HWTACACS scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local authentication.

none: Does not perform authentication.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

You can specify one primary authentication method and multiple backup authentication methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the authentication ppp radius-scheme radius-scheme-name local none command specifies a primary RADIUS authentication method and two backup methods (local authentication and no authentication). The device performs RADIUS authentication by default and performs local authentication when the RADIUS server is invalid. The device does not perform authentication when both of the previous methods are invalid.

When the primary authentication method is local, the following rules apply to the authentication of a user:

· The device uses the backup authentication methods in sequence only if local authentication is invalid for one of the following reasons:

¡ An exception occurs in the local authentication process.

¡ The user account is not configured on the device or the user is not allowed to use the PPP service.

· The device does not turn to the backup authentication methods if local authentication is invalid because of any other reason. Authentication fails for the user.

Examples

# In ISP domain test, perform local authentication for PPP users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authentication ppp local

# In ISP domain test, perform RADIUS authentication for PPP users based on scheme rd and use local authentication as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authentication ppp radius-scheme rd local

Related commands

authentication default

hwtacacs scheme

local-user

radius scheme

authentication sslvpn

Use authentication sslvpn to specify authentication methods for SSL VPN users.

Use undo authentication sslvpn to restore the default.

Syntax

In non-FIPS mode:

authentication sslvpn { ldap-scheme ldap-scheme-name [ local ] [ none ] | local [ ldap-scheme ldap-scheme-name | radius-scheme radius-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ local ] [ none ] }

undo authentication sslvpn

In FIPS mode:

authentication sslvpn { ldap-scheme ldap-scheme-name [ local ] | local [ ldap-scheme ldap-scheme-name | radius-scheme radius-scheme-name ] | radius-scheme radius-scheme-name [ local ] }

undo authentication sslvpn

Default

The default authentication methods of the ISP domain are used for SSL VPN users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

ldap-scheme ldap-scheme-name: Specifies an LDAP scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local authentication.

none: Does not perform authentication.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

You can specify one primary authentication method and multiple backup authentication methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the authentication sslvpn radius-scheme radius-scheme-name local none command specifies a primary RADIUS authentication method and two backup methods (local authentication and no authentication). The device performs RADIUS authentication by default and performs local authentication when the RADIUS server is invalid. The device does not perform authentication when both of the previous methods are invalid.

When the primary authentication method is local, the following rules apply to the authentication of a user:

· The device uses the backup authentication methods in sequence only if local authentication is invalid for one of the following reasons:

¡ An exception occurs in the local authentication process.

¡ The user account is not configured on the device or the user is not allowed to use the SSL VPN service.

· The device does not turn to the backup authentication methods if local authentication is invalid because of any other reason. Authentication fails for the user.

Examples

# In ISP domain test, perform local authentication for SSL VPN users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authentication sslvpn local

# In ISP domain test, perform LDAP authentication for SSL VPN users based on scheme ldp and use local authentication as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authentication sslvpn ldap-scheme ldp local

Related commands

authentication default

ldap scheme

local-user

radius scheme

authentication super

Use authentication super to specify a method for user role authentication.

Use undo authentication super to restore the default.

Syntax

authentication super { hwtacacs-scheme hwtacacs-scheme-name | radius-scheme radius-scheme-name } *

undo authentication super

Default

The default authentication methods of the ISP domain are used for user role authentication.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

hwtacacs-scheme hwtacacs-scheme-name: Specifies an HWTACACS scheme by its name, a case-insensitive string of 1 to 32 characters.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

To enable a user to obtain another user role without reconnecting to the device, you must configure user role authentication. The device supports local and remote methods for user role authentication. For more information about user role authentication, see RBAC configuration in Fundamentals Configuration Guide.

You can specify one authentication method and one backup authentication method to use in case that the previous authentication method is invalid.

Examples

# In ISP domain test, perform user role authentication based on HWTACACS scheme tac.

<Sysname> system-view

[Sysname] super authentication-mode scheme

[Sysname] domain test

[Sysname-isp-test] authentication super hwtacacs-scheme tac

Related commands

authentication default

hwtacacs scheme

radius scheme

authorization advpn

Use authorization advpn to specify authorization methods for ADVPN users.

Use undo authorization advpn to restore the default.

Syntax

In non-FIPS mode:

authorization advpn { local [ radius-scheme radius-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ local ] [ none ] }

undo authorization advpn

In FIPS mode:

authorization advpn { local | radius-scheme radius-scheme-name } *

undo authorization advpn

Default

The default authorization methods of the ISP domain are used for ADVPN users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

local: Performs local authorization.

none: Does not perform authorization.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

The RADIUS authorization configuration takes effect only when authentication and authorization methods of the ISP domain use the same RADIUS scheme.

You can specify one primary authorization method and multiple backup authorization methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the authorization advpn radius-scheme radius-scheme-name local none command specifies a primary RADIUS authorization method and two backup methods (local authorization and no authorization). The device performs RADIUS authorization by default and performs local authorization when the RADIUS server is invalid. The device does not perform authorization when both of the previous methods are invalid.

When the primary authorization method is local, the following rules apply to the authorization of a user:

· The device uses the backup authorization methods in sequence only if local authorization is invalid for one of the following reasons:

¡ An exception occurs in the local authorization process.

¡ The user account is not configured on the device or the user is not allowed to use the ADVPN service.

· The device does not turn to the backup authorization methods if local authorization is invalid because of any other reason. Authorization fails for the user.

Examples

# In ISP domain test, perform local authorization for ADVPN users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization advpn local

# In ISP domain test, perform RADIUS authorization for ADVPN users based on scheme rd and use local authorization as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization advpn radius-scheme rd local

Related commands

authorization default

local-user

radius scheme

authorization command

Use authorization command to specify command authorization methods.

Use undo authorization command to restore the default.

Syntax

In non-FIPS mode:

authorization command { hwtacacs-scheme hwtacacs-scheme-name [ local ] [ none ] | local [ none ] | none }

undo authorization command

In FIPS mode:

authorization command { hwtacacs-scheme hwtacacs-scheme-name [ local ] | local }

undo authorization command

Default

The default authorization methods of the ISP domain are used for command authorization.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

hwtacacs-scheme hwtacacs-scheme-name: Specifies an HWTACACS scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local authorization.

none: Does not perform authorization. The authorization server does not verify whether the entered commands are permitted by the user role. The commands are executed successfully if the user role has permission to the commands.

Usage guidelines

Command authorization restricts login users to execute only authorized commands by employing an authorization server to verify whether each entered command is permitted.

When local command authorization is configured, the device compares each entered command with the user's configuration on the device. The command is executed only when it is permitted by the user's authorized user roles.

The commands that can be executed are controlled by both the access permission of user roles and command authorization of the authorization server. Access permission only controls whether the authorized user roles have access to the entered commands, but it does not control whether the user roles have obtained authorization to these commands. If a command is permitted by the access permission but denied by command authorization, this command cannot be executed.

You can specify one primary command authorization method and multiple backup command authorization methods.

When the default authorization method is invalid, the device attempts to use the backup authorization methods in sequence. For example, the authorization command hwtacacs-scheme hwtacacs-scheme-name local none command specifies the default HWTACACS authorization method and two backup methods (local authorization and no authorization). The device performs HWTACACS authorization by default and performs local authorization when the HWTACACS server is invalid. The device does not perform command authorization when both of the previous methods are invalid.

Examples

# In ISP domain test, configure the device to perform local command authorization.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization command local

# In ISP domain test, perform command authorization based on HWTACACS scheme hwtac and use local authorization as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization command hwtacacs-scheme hwtac local

Related commands

command authorization (Fundamentals Command Reference)

hwtacacs scheme

local-user

authorization default

Use authorization default to specify default authorization methods for an ISP domain.

Use undo authorization default to restore the default.

Syntax

In non-FIPS mode:

authorization default { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] [ none ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * [ none ] | none | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] [ none ] }

undo authorization default

In FIPS mode:

authorization default { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] }

undo authorization default

Default

The default authorization method of an ISP domain is local.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

hwtacacs-scheme hwtacacs-scheme-name: Specifies an HWTACACS scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local authorization.

none: Does not perform authorization. The following default authorization information applies after users pass authentication:

· Login users obtain the level-0 user role. Login users include the Telnet, FTP, SFTP, SCP, and terminal users. Terminal users can access the device through the console, AUX, or asyn port. For more information about the level-0 user role, see RBAC configuration in Fundamentals Configuration Guide.

· The working directory for FTP, SFTP, and SCP login users is the root directory of the NAS. However, the users do not have permission to access the root directory.

· Non-login users can access the network.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

The default authorization method is used for all users that support this method and do not have an authorization method configured.

The RADIUS authorization configuration takes effect only when the authentication method and authorization method of the ISP domain use the same RADIUS scheme.

You can specify one primary authorization method and multiple backup authorization methods.

When the default authorization method is invalid, the device attempts to use the backup authorization methods in sequence. For example, the authorization default radius-scheme radius-scheme-name local none command specifies the default RADIUS authorization method and two backup methods (local authorization and no authorization). The device performs RADIUS authorization by default and performs local authorization when the RADIUS server is invalid. The device does not perform authorization when both of the previous methods are invalid.

When the primary authorization method is local, the following rules apply to the authorization of a user:

· The device uses the backup authorization methods in sequence only if local authorization is invalid for one of the following reasons:

¡ An exception occurs in the local authorization process.

¡ The user account is not configured on the device or the user is not allowed to use the access service.

· The device does not turn to the backup authorization methods if local authorization is invalid because of any other reason. Authorization fails for the user.

Examples

# In ISP domain test, use RADIUS scheme rd as the primary default authorization method and use local authorization as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization default radius-scheme rd local

Related commands

hwtacacs scheme

local-user

radius scheme

authorization ike

Use authorization ike to specify authorization methods for IKE extended authentication.

Use undo authorization ike to restore the default.

Syntax

In non-FIPS mode:

authorization ike { local [ radius-scheme radius-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ local ] [ none ] }

undo authorization ike

In FIPS mode:

authorization ike { local | radius-scheme radius-scheme-name [ local ] }

undo authorization ike

Default

The default authorization methods of the ISP domain are used for IKE extended authentication.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

local: Performs local authorization.

none: Does not perform authorization.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

You can specify one primary authorization method and multiple backup authorization methods.

When the default authorization method is invalid, the device attempts to use the backup authorization methods in sequence. For example, the authorization ike radius-scheme radius-scheme-name local none command specifies the default RADIUS authorization method and two backup methods (local authorization and no authorization). The device performs RADIUS authorization by default and performs local authorization when the RADIUS server is invalid. The device does not perform authorization when both of the previous methods are invalid.

When the primary authorization method is local, the following rules apply to the authorization of a user:

· The device uses the backup authorization methods in sequence only if local authorization is invalid for one of the following reasons:

¡ An exception occurs in the local authorization process.

¡ The user account is not configured on the device or the user is not allowed to use the IKE service.

· The device does not turn to the backup authorization methods if local authorization is invalid because of any other reason. Authorization fails for the user.

Examples

# In ISP domain test, perform local authorization for IKE extended authentication.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization ike local

Related commands

authorization default

local-user

authorization lan-access

Use authorization lan-access to specify authorization methods for LAN users.

Use undo authorization lan-access to restore the default.

Syntax

In non-FIPS mode:

authorization lan-access { local [ radius-scheme radius-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ local ] [ none ] }

undo authorization lan-access

In FIPS mode:

authorization lan-access { local | radius-scheme radius-scheme-name } *

undo authorization lan-access

Default

The default authorization methods of the ISP domain are used for LAN users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

local: Performs local authorization.

none: Does not perform authorization. An authenticated LAN user directly accesses the network.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

The RADIUS authorization configuration takes effect only when authentication and authorization methods of the ISP domain use the same RADIUS scheme.

You can specify one primary authorization method and multiple backup authorization methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the authorization lan-access radius-scheme radius-scheme-name local none command specifies a primary RADIUS authorization method and two backup methods (local authorization and no authorization). The device performs RADIUS authorization by default and performs local authorization when the RADIUS server is invalid. The device does not perform authorization when both of the previous methods are invalid.

When the primary authorization method is local, the following rules apply to the authorization of a user:

· The device uses the backup authorization methods in sequence only if local authorization is invalid for one of the following reasons:

¡ An exception occurs in the local authorization process.

¡ The user account is not configured on the device or the user is not allowed to use the LAN access service.

· The device does not turn to the backup authorization methods if local authorization is invalid because of any other reason. Authorization fails for the user.

Examples

# In ISP domain test, perform local authorization for LAN users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization lan-access local

# In ISP domain test, perform RADIUS authorization for LAN users based on scheme rd and use local authorization as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization lan-access radius-scheme rd local

Related commands

authorization default

local-user

radius scheme

authorization login

Use authorization login to specify authorization methods for login users.

Use undo authorization login to restore the default.

Syntax

In non-FIPS mode:

authorization login { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] [ none ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * [ none ] | none | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] [ none ] }

undo authorization login

In FIPS mode:

authorization login { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] }

undo authorization login

Default

The default authorization methods of the ISP domain are used for login users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

hwtacacs-scheme hwtacacs-scheme-name: Specifies an HWTACACS scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local authorization.

none: Does not perform authorization. The following default authorization information applies after users pass authentication:

· The working directory for FTP, SFTP, and SCP login users is the root directory of the NAS. However, the users do not have permission to access the root directory.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

The RADIUS authorization configuration takes effect only when the authentication method and authorization method of the ISP domain use the same RADIUS scheme.

You can specify one primary authorization method and multiple backup authorization methods.

When the default authorization method is invalid, the device attempts to use the backup authorization methods in sequence. For example, the authorization login radius-scheme radius-scheme-name local none command specifies the default RADIUS authorization method and two backup methods (local authorization and no authorization). The device performs RADIUS authorization by default and performs local authorization when the RADIUS server is invalid. The device does not perform authorization when both of the previous methods are invalid.

When the primary authorization method is local, the following rules apply to the authorization of a user:

· The device uses the backup authorization methods in sequence only if local authorization is invalid for one of the following reasons:

¡ An exception occurs in the local authorization process.

¡ The user account is not configured on the device or the user is not allowed to use the service for accessing the device.

· The device does not turn to the backup authorization methods if local authorization is invalid because of any other reason. Authorization fails for the user.

Examples

# In ISP domain test, perform local authorization for login users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization login local

# In ISP domain test, perform RADIUS authorization for login users based on scheme rd and use local authorization as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization login radius-scheme rd local

Related commands

authorization default

hwtacacs scheme

local-user

radius scheme

authorization portal

Use authorization portal to specify authorization methods for portal users.

Use undo authorization portal to restore the default.

Syntax

In non-FIPS mode:

authorization portal { local [ radius-scheme radius-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ local ] [ none ] }

undo authorization portal

In FIPS mode:

authorization portal { local | radius-scheme radius-scheme-name } *

undo authorization portal

Default

The default authorization methods of the ISP domain are used for portal users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

local: Performs local authorization.

none: Does not perform authorization. An authenticated portal user directly accesses the network.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

The RADIUS authorization configuration takes effect only when the authentication method and authorization method of the ISP domain use the same RADIUS scheme.

You can specify one primary authorization method and multiple backup authorization methods.

When the default authorization method is invalid, the device attempts to use the backup authorization methods in sequence. For example, the authorization portal radius-scheme radius-scheme-name local none command specifies the default RADIUS authorization method and two backup methods (local authorization and no authorization). The device performs RADIUS authorization by default and performs local authorization when the RADIUS server is invalid. The device does not perform authorization when both of the previous methods are invalid.

When the primary authorization method is local, the following rules apply to the authorization of a user:

· The device uses the backup authorization methods in sequence only if local authorization is invalid for one of the following reasons:

¡ An exception occurs in the local authorization process.

¡ The user account is not configured on the device or the user is not allowed to use the portal service.

· The device does not turn to the backup authorization methods if local authorization is invalid because of any other reason. Authorization fails for the user.

Examples

# In ISP domain test, perform local authorization for portal users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization portal local

# In ISP domain test, perform RADIUS authorization for portal users based on scheme rd and use local authorization as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization portal radius-scheme rd local

Related commands

authorization default

local-user

radius scheme

authorization ppp

Use authorization ppp to specify authorization methods for PPP users.

Use undo authorization ppp to restore the default.

Syntax

In non-FIPS mode:

authorization ppp { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] [ none ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * [ none ] | none | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] [ none ] }

undo authorization ppp

In FIPS mode:

authorization ppp { hwtacacs-scheme hwtacacs-scheme-name [ radius-scheme radius-scheme-name ] [ local ] | local [ radius-scheme radius-scheme-name | hwtacacs-scheme hwtacacs-scheme-name ] * | radius-scheme radius-scheme-name [ hwtacacs-scheme hwtacacs-scheme-name ] [ local ] }

undo authorization ppp

Default

The default authorization methods of the ISP domain are used for PPP users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

hwtacacs-scheme hwtacacs-scheme-name: Specifies an HWTACACS scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local authorization.

none: Does not perform authorization.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

The RADIUS authorization configuration takes effect only when the authentication method and authorization method of the ISP domain use the same RADIUS scheme.

You can specify one primary authorization method and multiple backup authorization methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the authorization ppp radius-scheme radius-scheme-name local none command specifies a primary RADIUS authorization method and two backup methods (local authorization and no authorization). The device performs RADIUS authorization by default and performs local authorization when the RADIUS server is invalid. The device does not perform authorization when both of the previous methods are invalid.

When the primary authorization method is local, the following rules apply to the authorization of a user:

· The device uses the backup authorization methods in sequence only if local authorization is invalid for one of the following reasons:

¡ An exception occurs in the local authorization process.

¡ The user account is not configured on the device or the user is not allowed to use the PPP service.

· The device does not turn to the backup authorization methods if local authorization is invalid because of any other reason. Authorization fails for the user.

Examples

# In ISP domain test, perform local authorization for PPP users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization ppp local

# In ISP domain test, perform RADIUS authorization for PPP users based on scheme rd and use local authorization as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization ppp radius-scheme rd local

Related commands

authorization default

hwtacacs scheme

local-user

radius scheme

authorization sslvpn

Use authorization sslvpn to specify authorization methods for SSL VPN users.

Use undo authorization sslvpn to restore the default.

Syntax

In non-FIPS mode:

authorization sslvpn { ldap-scheme ldap-scheme-name [ local ] [ none ] | local [ ldap-scheme ldap-scheme-name | radius-scheme radius-scheme-name ] [ none ] | none | radius-scheme radius-scheme-name [ local ] [ none ] }

undo authorization sslvpn

In FIPS mode:

authorization sslvpn { ldap-scheme ldap-scheme-name [ local ] | local [ ldap-scheme ldap-scheme-name | radius-scheme radius-scheme-name ] | radius-scheme radius-scheme-name [ local ] }

undo authorization sslvpn

Default

The default authorization methods of the ISP domain are used for SSL VPN users.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

ldap-scheme ldap-scheme-name: Specifies an LDAP scheme by its name, a case-insensitive string of 1 to 32 characters.

local: Performs local authorization.

none: Does not perform authorization. Authenticated SSL VPN users can access the network directly.

radius-scheme radius-scheme-name: Specifies a RADIUS scheme by its name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

The RADIUS authorization configuration takes effect only when the authentication method and authorization method of the ISP domain use the same RADIUS scheme.

You can specify one primary authorization method and multiple backup authorization methods.

When the primary method is invalid, the device attempts to use the backup methods in sequence. For example, the authorization sslvpn radius-scheme radius-scheme-name local none command specifies a primary RADIUS authorization method and two backup methods (local authorization and no authorization). The device performs RADIUS authorization by default and performs local authorization when the RADIUS server is invalid. The device does not perform authorization when both of the previous methods are invalid.

When the primary authorization method is local, the following rules apply to the authorization of a user:

· The device uses the backup authorization methods in sequence only if local authorization is invalid for one of the following reasons:

¡ An exception occurs in the local authorization process.

¡ The user account is not configured on the device or the user is not allowed to use the SSL VPN service.

· The device does not turn to the backup authorization methods if local authorization is invalid because of any other reason. Authorization fails for the user.

Examples

# In ISP domain test, perform local authorization for SSL VPN users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization sslvpn local

# In ISP domain test, perform LDAP authorization for SSL VPN users based on scheme ldp and use local authorization as the backup.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization sslvpn ldap-scheme ldp local

Related commands

authorization default

ldap scheme

local-user

radius scheme

authorization-attribute (ISP domain view)

Use authorization-attribute to configure authorization attributes for users in an ISP domain.

Use undo authorization-attribute to restore the default of an authorization attribute.

Syntax

authorization-attribute { acl acl-number | car inbound cir committed-information-rate [ pir peak-information-rate ] outbound cir committed-information-rate [ pir peak-information-rate ] | idle-cut minutes [ flow ] | igmp max-access-number max-access-number | ip-pool ipv4-pool-name | ipv6-pool ipv6-pool-name | ipv6-prefix ipv6-prefix prefix-length | mld max-access-number max-access-number | { primary-dns | secondary-dns } { ip ipv4-address | ipv6 ipv6-address } | session-group-profile session-group-profile-name | session-timeout minutes | url url-string | user-group user-group-name | user-profile profile-name | vpn-instance vpn-instance-name }

undo authorization-attribute { acl | car | idle-cut | igmp | ip-pool | ipv6-pool | ipv6-prefix | mld | primary-dns | secondary-dns | session-group-profile | session-timeout | url | user-group | user-profile | vpn-instance }

Default

The idle cut feature is disabled.

An IPv4 user can concurrently join a maximum of four IGMP multicast groups.

An IPv6 user can concurrently join a maximum of four MLD multicast groups.

No other authorization attributes exist.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

acl acl-number: Specifies an ACL to filter traffic for users. The value range for the acl-number argument is 2000 to 4999. This option is applicable only to portal and LAN users. The device processes the traffic that matches the rules in the authorization ACL based on the permit or deny statement in the rules.

car: Specifies a CAR action for users. Typically, the attribute applies to authenticated users. If you configure the attribute in a portal preauthentication domain, the CAR action applies before portal authentication. This keyword is applicable only to portal and PPP users.

inbound: Specifies the upload rate of users.

outbound: Specifies the download rate of users.

cir committed-information-rate: Specifies the committed information rate in kbps, in the range of 1 to 4194303.

pir peak-information-rate: Specifies the peak information rate in kbps, in the range of 1 to 4194303. The peak information rate cannot be smaller than the committed information rate. If you do not specify this option, the CAR action does not restrict users by peak information rate.

idle-cut minutes: Specifies an idle timeout period in minutes. The value range for the minutes argument is 1 to 600. This option is applicable only to portal and PPP users.

flow: Specifies the minimum traffic that must be generated in the idle timeout period in bytes. The value range is 1 to 10240000, and the default value is 10240.

igmp max-access-number max-access-number: Specifies the maximum number of IGMP groups that an IPv4 user can join concurrently. The value range for the max-access-number argument is 1 to 64. This option is applicable only to portal and PPP users.

ip-pool ipv4-pool-name: Specifies an IPv4 address pool for users. The ipv4-pool-name argument is a case-insensitive string of 1 to 63 characters. This option is applicable only to PPP, IKE, and portal users.

ipv6-pool ipv6-pool-name: Specifies an IPv6 address pool for users. The ipv6-pool-name argument is a case-insensitive string of 1 to 63 characters. This option is applicable only to portal and PPP users.

ipv6-prefix ipv6-prefix prefix-length: Specifies an IPv6 address prefix for users. The value range for the prefix-length argument is 1 to 128. This option is applicable only to PPP users.

mld max-access-number max-access-number: Specifies the maximum number of MLD groups that an IPv6 user can join concurrently. The value range for the max-access-number argument is 1 to 64. This option is applicable only to portal and PPP users.

primary-dns ip ipv4-address: Specifies the IPv4 address of the primary DNS server for users. This option is applicable only to PPP users.

primary-dns ipv6 ipv6-address: Specifies the IPv6 address of the primary DNS server for users. This option is applicable only to PPP users.

secondary-dns ip ipv4-address: Specifies the IPv4 address of the secondary DNS server for users. This option is applicable only to PPP users.

secondary-dns ipv6 ipv6-address: Specifies the IPv6 address of the secondary DNS server for users. This option is applicable only to PPP users.

session-group-profile session-group-profile-name: Specifies an authorization session group profile for users. The session-group-profile-name argument is a case-sensitive string of 1 to 31 characters. Typically, the attribute applies to authenticated users. If you configure the attribute in a portal preauthentication domain, the session group profile applies before portal authentication. This option is applicable only to portal and PPP users.

session-timeout minutes: Specifies the session timeout timer for users, in minutes. The value range for the minutes argument is 1 to 4294967295. The device logs off a user when the user's session timeout timer expires. This option is applicable only to PPP, portal, and LAN users.

url url-string: Specifies a redirect URL for users. Users are redirected to the URL the first time they access the network after they pass authentication. The url-string argument is a case-sensitive string of 1 to 255 characters. This option is applicable only to PPP and LAN users.

user-group user-group-name: Specifies a user group for users. The user-group-name argument is a case-insensitive string of 1 to 32 characters. Authenticated users obtain all attributes of the user group.

user-profile profile-name: Specifies an authorization user profile. The profile-name argument is a case-sensitive string of 1 to 31 characters. Typically, the attribute applies to authenticated users. If you configure the attribute in a portal preauthentication domain, the user profile applies before portal authentication. This option is applicable only to PPP, portal, and LAN users.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance to which the users belong. The vpn-instance-name argument is a case-sensitive string of 1 to 31 characters. When a user passes authentication, it has permission to access the network resources in the specified VPN. This option is applicable only to PPP, and portal users.

Usage guidelines

When the idle cut feature is configured, the device periodically detects the traffic of each online user. The device logs out users that do not meet the minimum traffic requirement in the idle timeout period. When the idle cut feature is disabled on the device, the idle cut feature of the server takes effect. The server considers a user idle if the user's traffic is less than 10240 bytes in a configurable idle timeout period.

If the server or NAS does not authorize a type of attribute to an authenticated user, the device authorizes the attribute in the ISP domain to the user.

You can configure multiple authorization attributes for users in an ISP domain. If you execute the command multiple times with the same attribute specified, the most recent configuration takes effect.

For portal users to come online after passing authentication, make sure ACLs assigned to portal users do not have rules specified with a source IP or MAC address.

Examples

# Specify user group abc as the authorization user group for users in ISP domain test.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] authorization-attribute user-group abc

Related commands

display domain

basic-service-ip-type

Use basic-service-ip-type to specify the types of IP addresses that PPPoE and L2TP users must rely on to use the basic services.

Use undo basic-service-ip-type to restore the default.

Syntax

basic-service-ip-type { ipv4 | ipv6 | ipv6-pd } *

undo basic-service-ip-type

Default

PPPoE and L2TP users do not rely on any types of IP addresses to use the basic services.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

ipv4: Specifies the IPv4 address type.

ipv6: Specifies the IPv6 address type.

ipv6-pd: Specifies the IPv6-PD address type. This type of IPv6 addresses are generated based on the DHCPv6 server-assigned prefix.

Usage guidelines

This command takes effect only when the device acts as a PPPoE server or L2TP LNS and only on PPPoE and L2TP users.

A user might request multiple services of different IP address types. By default, the device logs off the user if the user does not obtain an IP address. This command enables the device to allow the user to come online if the user has obtained IP addresses of all the specified types for the basic services.

The device does not allow a user to come online if the user does not obtain IP addresses of all the specified types for the basic services. For example, if you execute the basic-service-ip-type ipv6 command, the device does not allow a user to come online if the user does not obtain an IPv6 address.

If you specify both the ipv6 and ipv6-pd keywords, the device does not allow a user that fails IPv6 address negotiation or PD negotiation to come online.

Examples

# In ISP domain test, specify PPPoE and L2TP users to rely on IPv4 addresses to use the basic services.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] basic-service-ip-type ipv4

dhcpv6-follow-ipv6cp

Use dhcpv6-follow-ipv6cp to set the IPv6 address wait timer for PPPoE and L2TP users.

Use undo dhcpv6-follow-ipv6cp to restore the default.

Syntax

dhcpv6-follow-ipv6cp timeout delay-time

undo dhcpv6-follow-ipv6cp

Default

The IPv6 address wait timer for PPPoE and L2TP users is 60 seconds.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

timeout delay-time: Specifies the IPv6 address wait timer, in the range of 30 to 120 seconds.

Usage guidelines

The IPv6 address wait timer defines the maximum amount of time that a user can wait before the device determines that the user fails to obtain an IPv6 address or PD prefix.

This command takes effect only when the device acts as a PPPoE server or L2TP LNS and only on PPPoE and L2TP users.

The device starts an IPv6 address wait timer for a user after it finishes IPv6CP negotiation with the user. If the user's basic service relies on an IPv6 address or PD prefix but it fails to obtain any IPv6 address or PD prefix when the timer expires, the user cannot come online.

As a best practice, increase the IPv6 address wait timer in the following situations:

· The network communication is unstable.

· The device uses DHCPv6 to assign IPv6 addresses to users.

· The ISP domain serves a large number of users.

Examples

# In ISP domain test, set the IPv6 address wait timer to 90 seconds for PPPoE and L2TP users.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] dhcpv6-follow-ipv6cp timeout 90

Related commands

basic-service-ip-type

display domain

Use display domain to display ISP domain configuration.

Syntax

display domain [ isp-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

isp-name: Specifies an ISP domain by its name, a case-insensitive string of 1 to 255 characters. If you do not specify an ISP domain, this command displays the configuration of all ISP domains.

Examples

# Display the configuration of all ISP domains.

<Sysname> display domain

Total 2 domains

Domain: system

State: Active

Default authentication scheme: Local

Default authorization scheme: Local

Default accounting scheme: Local

Accounting start failure action: Online

Accounting update failure action: Online

Accounting quota out action: Offline

Service type: HSI

Session time: Exclude idle time

NAS-ID: N/A

DHCPv6-follow-IPv6CP timeout: 60 seconds

Authorization attributes:

Idle cut: Disabled

Session timeout: Disabled

IGMP access limit: 4

MLD access limit: 4

Domain: dm

State: Active

Super authentication scheme: RADIUS=rad

Command authorization scheme: HWTACACS=hw

LAN access authentication scheme: RADIUS=r4

PPP accounting scheme: RADIUS=r1, (RADIUS=r2), HWTACACS=tc, Local

Portal authentication scheme: LDAP=ldp

SSL VPN authentication scheme: LDAP=ldp, Local, None

SSL VPN authorization scheme: LDAP=ldp, Local

SSL VPN accounting scheme: None

Default authentication scheme: RADIUS=rad, Local, None

Default authorization scheme: Local

Default accounting scheme: None

Accounting start failure action: Online

Accounting update failure action: Online

Accounting quota out action: Offline

Service type: HSI

Session time: Include idle time

User address type: ipv4

NAS-ID: test

User basic service IP type: IPv4

DHCPv6-follow-IPv6CP timeout: 44 seconds

Authorization attributes:

Idle cut : Enabled

Idle timeout: 2 minutes

Flow: 10240 bytes

Session timeout: 34 minutes

IP pool: appy

User profile: test

Session group profile: abc

Inbound CAR: CIR 64000 bps PIR 640000 bps

Outbound CAR: CIR 64000 bps PIR 640000 bps

ACL number: 3000

User group: ugg

IPv6 prefix: 1::1/34

IPv6 pool: ipv6pool

Primary DNS server: 6.6.6.6

Secondary DNS server: 3.6.2.3

URL: http://test

VPN instance: vpn1

IGMP access limit: 4

MLD access limit: 4

Default domain name: system

Table 1 Command output

Field	Description
Domain	ISP domain name.
State	Status of the ISP domain.
Default authentication scheme	Default authentication methods.
Default authorization scheme	Default authorization methods.
Default accounting scheme	Default accounting methods.
ADVPN authentication scheme	Authentication methods for ADVPN users.
ADVPN authorization scheme	Authorization methods for ADVPN users.
ADVPN accounting scheme	Accounting methods for ADVPN users.
Login authentication scheme	Authentication methods for login users.
Login authorization scheme	Authorization methods for login users.
Login accounting scheme	Accounting methods for login users.
Super authentication scheme	Authentication methods for obtaining another user role without reconnecting to the device.
PPP authentication scheme	Authentication methods for PPP users.
PPP authorization scheme	Authorization methods for PPP users.
PPP accounting scheme	Accounting methods for PPP users.
Command authorization scheme	Command line authorization methods.
Command accounting scheme	Command line accounting method.
LAN access authentication scheme	Authentication methods for LAN users.
LAN access authorization scheme	Authorization methods for LAN users.
LAN access accounting scheme	Accounting methods for LAN users.
Portal authentication scheme	Authentication methods for portal users.
Portal authorization scheme	Authorization methods for portal users.
Portal accounting scheme	Accounting methods for portal users.
IKE authentication scheme	IKE extended authentication methods.
IKE authorization scheme	Authorization methods for IKE extended authentication.
SSL VPN authentication scheme	Authentication methods for SSL VPN users.
SSL VPN authorization scheme	Authorization methods for SSL VPN users.
SSL VPN accounting scheme	Accounting methods for SSL VPN users.
RADIUS	RADIUS scheme.
HWTACACS	HWTACACS scheme.
LDAP	LDAP scheme.
Local	Local scheme.
None	No authentication, no authorization, or no accounting.
Accounting start failure action	Access control for users that encounter accounting-start failures: · Online—Allows the users to stay online. · Offline—Logs off the users.
Accounting update failure max-times	Maximum number of consecutive accounting-update failures allowed by the device for each user in the domain.
Accounting update failure action	Access control for users that have failed all their accounting-update attempts: · Online—Allows the users to stay online. · Offline—Logs off the users.
Accounting quota out action	Access control for users that have used up their accounting quotas: · Online—Allows the users to stay online. · Offline—Logs off the users.
Service type	Service type of the ISP domain, including HSI, STB, and VoIP.
Session time	Online duration sent to the server for users that went offline due to connection failure or malfunction: · Include idle time—The online duration includes the idle timeout period. · Exclude idle time—The online duration does not include the idle timeout period.
User address type	Type of IP addresses for users in the ISP domain. This field is not available if no user address type is specified in the ISP domain.
NAS-ID	NAS-ID of the device. This field displays N/A if no NAS-ID is set in the ISP domain.
User basic service IP type	Types of IP addresses that PPPoE and L2TP users rely on to use the basic services: · IPv4. · IPv6. · IPv6-PD.
DHCPv6-follow-IPv6CP timeout	IPv6 address wait timer (in seconds) that starts after IPv6CP negotiation for PPPoE and L2TP users.
Authorization attributes	Authorization attributes for users in the ISP domain.
Idle cut	Idle cut feature status: · Enabled—The feature is enabled. The device logs off users that do not meet the minimum traffic requirements in an idle timeout period. · Disabled—The feature is disabled. It is the default idle cut state.
Idle timeout	Idle timeout period, in minutes.
Flow	Minimum traffic that a login user must generate in an idle timeout period, in bytes.
Session timeout	Session timeout time for users in the ISP domain, in minutes.
IP pool	Name of the authorization IPv4 address pool.
User profile	Name of the authorization user profile.
Session group profile	Name of the authorization session group profile.
Inbound CAR	Authorization inbound CAR: · CIR—Committed information rate in bps. · PIR—Peak information rate in bps.
Outbound CAR	Authorization outbound CAR: · CIR—Committed information rate in bps. · PIR—Peak information rate in bps.
ACL number	Authorization ACL for users.
User group	Authorization user group for users.
IPv6 prefix	Authorization IPv6 address prefix for users.
IPv6 pool	Name of the authorization IPv6 address pool for users.
Primary DNS server	IPv4 address of the authorization primary DNS server for users.
Secondary DNS server	IPv4 address of the authorization secondary DNS server for users.
Primary DNSV6 server	IPv6 address of the authorization primary DNS server for users.
Secondary DNSV6 server	IPv6 address of the authorization secondary DNS server for users.
URL	Authorization redirect URL for users.
VPN instance	Name of the authorization VPN instance for users.
IGMP access limit	Maximum number of IGMP groups that an IPv4 user is authorized to join concurrently.
MLD access limit	Maximum number of MLD groups that an IPv6 user is authorized to join concurrently.

‌

domain

Use domain to create an ISP domain and enter its view, or enter the view of an existing ISP domain.

Use undo domain to delete an ISP domain.

Syntax

domain isp-name

undo domain isp-name

Default

A system-defined ISP domain exists. The domain name is system.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

isp-name: Specifies the ISP domain name, a case-insensitive string of 1 to 255 characters. The name must meet the following requirements:

· The name cannot contain a forward slash (/), backslash (\), vertical bar (|), quotation marks ("), colon (:), asterisk (*), question mark (?), left angle bracket (<), right angle bracket (>), or at sign (@).

· The name cannot be d, de, def, defa, defau, defaul, default, i, if, if-, if-u, if-un, if-unk, if-unkn, if-unkno, if-unknow, or if-unknown.

Usage guidelines

All ISP domains are in active state when they are created.

You can modify settings for the system-defined ISP domain system, but you cannot delete this domain.

An ISP domain cannot be deleted when it is the default ISP domain. Before you use the undo domain command, change the domain to a non-default ISP domain by using the undo domain default enable command.

Use short domain names to ensure that user names containing a domain name do not exceed the maximum name length required by different types of users.

Examples

# Create an ISP domain named test and enter ISP domain view.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test]

Related commands

display domain

domain default enable

domain if-unknown

state (ISP domain view)

domain default enable

Use domain default enable to specify the default ISP domain. Users without any domain name included in the usernames are considered in the default domain.

Use undo domain default enable to restore the default.

Syntax

domain default enable isp-name

undo domain default enable

Default

The default ISP domain is the system-defined ISP domain system.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

isp-name: Specifies the ISP domain name, a case-insensitive string of 1 to 255 characters. The ISP domain must already exist.

Usage guidelines

The system has only one default ISP domain.

Examples

# Create an ISP domain named test, and configure the domain as the default ISP domain.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] quit

[Sysname] domain default enable test

Related commands

display domain

domain

domain if-unknown

Use domain if-unknown to specify an ISP domain to accommodate users that are assigned to nonexistent domains.

Use undo domain if-unknown to restore the default.

Syntax

domain if-unknown isp-name

undo domain if-unknown

Default

No ISP domain is specified to accommodate users that are assigned to nonexistent domains.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

isp-name: Specifies the ISP domain name, a case-insensitive string of 1 to 255 characters. The name must meet the following requirements:

· The name cannot be d, de, def, defa, defau, defaul, default, i, if, if-, if-u, if-un, if-unk, if-unkn, if-unkno, if-unknow, or if-unknown.

Usage guidelines

The device chooses an authentication domain for each user in the following order:

1. The authentication domain specified for the access module.

2. The ISP domain in the username.

3. The default ISP domain of the device.

If the chosen domain does not exist on the device, the device searches for the ISP domain that accommodates users assigned to nonexistent domains. If no such ISP domain is configured, user authentication fails.

NOTE:

Support for the authentication domain configuration depends on the access module.

Examples

# Specify ISP domain test to accommodate users that are assigned to nonexistent domains.

<Sysname> system-view

[Sysname] domain if-unknown test

Related commands

display domain

nas-id

Use nas-id to set the NAS-ID in an ISP domain.

Use undo nas-id to restore the default.

Syntax

nas-id nas-identifier

undo nas-id

Default

No NAS-ID is set in an ISP domain.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

nas-identifier: Specifies a NAS-ID, a case-sensitive string of 1 to 31 characters.

Usage guidelines

During RADIUS authentication, the device uses a NAS-ID to set the NAS-Identifier attribute of RADIUS packets so that the RADIUS server can identify the access location of users.

You can configure a NAS-ID in NAS-ID profile view or in ISP domain view. The device selects the NAS-ID for the NAS-Identifier attribute in the following order:

1. NAS-ID bound with VLANs in a NAS-ID profile.

2. NAS-ID in an ISP domain.

If no NAS-ID is selected, the device uses the device name as the NAS-ID.

Examples

# Set the NAS-ID to test for ISP domain test.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] nas-id test

Related commands

aaa nas-id profile

nas-id bind vlan

Use nas-id bind vlan to bind a NAS-ID with a VLAN.

Use undo nas-id bind vlan to remove a NAS-ID and VLAN binding.

Syntax

nas-id nas-identifier bind vlan vlan-id

undo nas-id nas-identifier bind vlan vlan-id

Default

No NAS-ID and VLAN bindings exist.

Views

NAS-ID profile view

Predefined user roles

network-admin

mdc-admin

Parameters

nas-identifier: Specifies a NAS-ID, a case-sensitive string of 1 to 31 characters.

vlan-id: Specifies a VLAN ID in the range of 1 to 4094.

Usage guidelines

You can configure multiple NAS-ID and VLAN bindings in a NAS-ID profile.

A NAS-ID can be bound with more than one VLAN, but a VLAN can be bound with only one NAS-ID. If you configure multiple bindings for the same VLAN, the most recent configuration takes effect.

Examples

# Bind NAS-ID 222 with VLAN 2 in NAS-ID profile aaa.

<Sysname> system-view

[Sysname] aaa nas-id profile aaa

[Sysname-nas-id-prof-aaa] nas-id 222 bind vlan 2

Related commands

aaa nas-id profile

service-type (ISP domain view)

Use service-type to specify the service type for users in an ISP domain.

Use undo service-type to restore the default.

Syntax

service-type { hsi | stb | voip }

undo service-type

Default

The service type is hsi for users in an ISP domain.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

hsi: Specifies the High Speed Internet (HSI) service. This service is applicable to users that access the network through PPP.

stb: Specifies the Set Top Box (STB) service. This service is applicable to users that access the network through STB.

voip: Specifies the Voice over IP (VoIP) service. This service is applicable to users that access the network through IP phones.

Usage guidelines

When the HSI service is specified, the multicast feature of the access module is disabled to save system resources.

When the STB service is specified, the multicast feature of the access module is enabled to improve the performance of the multicast module.

When the VoIP service is specified, the QoS module increases the priority of voice traffic to reduce the transmission delay for IP phone users.

For PPP (excluding PPPoE) users, the system uses the HSI service forcibly even if the STB or VoIP service is specified.

You can configure only one service type for an ISP domain.

Examples

# Specify the STB service for users in ISP domain test.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] service-type stb

session-time include-idle-time

Use session-time include-idle-time to configure the device to include the idle timeout period in the user online duration sent to the server.

Use undo session-time include-idle-time to restore the default.

Syntax

session-time include-idle-time

undo session-time include-idle-time

Default

The device does not include the idle timeout period in the user online duration sent to the server.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

Whether to configure the device to include the idle timeout period in the user online duration sent to the server, depending on the accounting policy in your network. The idle timeout period is assigned to users by the authorization server after the users pass authentication. For portal users, the device includes the idle timeout period set for the online portal user detection feature in the user online duration. For more information about online detection for portal users, see portal authentication configuration in Security Configuration Guide.

If the user goes offline due to connection failure or malfunction, the user online duration sent to the server is not the same as the actual online duration.

· If the session-time include-idle-time command is used, the user's online duration sent to the server includes the idle timeout period. The online duration that is generated on the server is longer than the actual online duration of the user.

· If the undo session-time include-idle-time command is used, the user's online duration sent to the server excludes the idle timeout period. The online duration that is generated on the server is shorter than the actual online duration of the user.

Examples

# Configure the device to include the idle timeout period in the online duration sent to the server for users in ISP domain test.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] session-time include-idle-time

Related commands

display domain

state (ISP domain view)

Use state to set the status of an ISP domain.

Use undo state to restore the default.

Syntax

state { active | block }

undo state

Default

An ISP domain is in active state.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

active: Places the ISP domain in active state to allow the users in the ISP domain to request network services.

block: Places the ISP domain in blocked state to prevent users in the ISP domain from requesting network services.

Usage guidelines

By blocking an ISP domain, you disable offline users of the domain from requesting network services. However, the online users are not affected.

Examples

# Place ISP domain test in blocked state.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] state block

Related commands

display domain

user-address-type

Use user-address-type to specify the user address type in the ISP domain.

Use undo user-address-type to restore the default.

Syntax

user-address-type { ds-lite | ipv6 | nat64 | private-ds | private-ipv4 | public-ds | public-ipv4 }

undo user-address-type

Default

No user address type is specified for the ISP domain.

Views

ISP domain view

Predefined user roles

network-admin

mdc-admin

Parameters

ds-lite: Specifies the DS-Lite address type.

ipv6: Specifies the IPv6 address type.

nat64: Specifies the NAT64 address type.

private-ds: Specifies the private-DS address type.

private-ipv4: Specifies the private IPv4 address type.

public-ds: Specifies the public-DS address type.

public-ipv4: Specifies the public IPv4 address type.

Usage guidelines

Any change to the user address type does not affect online users.

Examples

# Specify the private IPv4 address type for users in ISP domain test.

<Sysname> system-view

[Sysname] domain test

[Sysname-isp-test] user-address-type private-ipv4

Related commands

display domain

Local user commands

access-limit

Use access-limit to set the maximum number of concurrent logins using the local user name.

Use undo access-limit to restore the default.

Syntax

access-limit max-user-number

undo access-limit

Default

The number of concurrent logins using the local user name is not limited.

Views

Local user view

Predefined user roles

network-admin

mdc-admin

Parameters

max-user-number: Specifies the maximum number of concurrent logins, in the range of 1 to 1024.

Usage guidelines

This command takes effect only when local accounting is configured for the local user.

The command does not apply to FTP, SFTP, or SCP users. These users do not support accounting.

Examples

# Set the maximum number of concurrent logins to 5 for users using the local user name abc.

<Sysname> system-view

[Sysname] local-user abc

[Sysname-luser-manage-abc] access-limit 5

Related commands

display local-user

authorization-attribute (local user view/user group view)

Use authorization-attribute to configure authorization attributes for a local user or user group. After the local user or a local user in the user group passes authentication, the device assigns these attributes to the user.

Use undo authorization-attribute to restore the default of an authorization attribute.

Syntax

authorization-attribute { acl acl-number | callback-number callback-number | idle-cut minutes | ip ipv4-address | ip-pool ipv4-pool-name | ipv6 ipv6-address | ipv6-pool ipv6-pool-name | ipv6-prefix ipv6-prefix prefix-length | { primary-dns | secondary-dns } { ip ipv4-address | ipv6 ipv6-address } | session-timeout minutes | sslvpn-policy-group group-name | url url-string | user-profile profile-name | user-role role-name | vlan vlan-id | vpn-instance vpn-instance-name | work-directory directory-name } *

undo authorization-attribute { acl | callback-number | idle-cut | ip | ip-pool | ipv6 | ipv6-pool | ipv6-prefix | primary-dns | secondary-dns| session-timeout | sslvpn-policy-group | url | user-profile | user-role role-name | vlan | vpn-instance | work-directory } *

Default

The working directory for FTP, SFTP, and SCP users is the root directory of the NAS. However, the users do not have permission to access the root directory.

The local users created by a network-admin or level-15 user on the default MDC are assigned the network-operator user role. The local users created by an mdc-admin or level-15 user on a non-default MDC are assigned the mdc-operator user role.

Views

Local user view

User group view

Predefined user roles

network-admin

mdc-admin

Parameters

acl acl-number: Specifies an authorization ACL. The value range for the acl-number argument is 2000 to 4999. The device processes the traffic that matches the rules in the authorization ACL based on the permit or deny statement in the rules.

callback-number callback-number: Specifies an authorized PPP callback number. The callback-number argument is a case-sensitive string of 1 to 64 characters. After a local user passes authentication, the device uses this number to call the user.

idle-cut minutes: Specifies an idle timeout period in minutes. The value range for the minutes argument is 1 to 120. An online user is logged out if its idle period exceeds the specified idle timeout period.

ip ipv4-address: Assigns a static IPv4 address to the user after it passes authentication.

ip-pool ipv4-pool-name: Specifies an IPv4 address pool for the user. The ipv4-pool-name argument is a case-insensitive string of 1 to 63 characters.

ipv6 ipv6-address: Assigns a static IPv6 address to the user after it passes authentication.

ipv6-pool ipv6-pool-name: Specifies an IPv6 address pool for the user. The ipv6-pool-name argument is a case-insensitive string of 1 to 63 characters.

ipv6-prefix ipv6-prefix prefix-length: Specifies an IPv6 address prefix for the user. The value range for the prefix-length argument is 1 to 128.

primary-dns ip ipv4-address: Specifies the IPv4 address of the primary DNS server for the user.

primary-dns ipv6 ipv6-address: Specifies the IPv6 address of the primary DNS server for the user.

secondary-dns ip ipv4-address: Specifies the IPv4 address of the secondary DNS server for the user.

secondary-dns ipv6 ipv6-address: Specifies the IPv6 address of the secondary DNS server for the user.

session-timeout minutes: Specifies the session timeout timer for the user, in minutes. The value range for the minutes argument is 1 to 1440. The device logs off the user after the timer expires.

sslvpn-policy-group group-name: Specifies an SSL VPN policy group for the user. The group-name argument is a case-insensitive string of 1 to 31 characters. For information about SSL VPN policy groups, see Security Configuration Guide.

url url-string: Specifies a PADM URL to which the user is redirected after it passes authentication. The url-string argument is a case-sensitive string of 1 to 255 characters. This option is applicable only to PPP users.

user-profile profile-name: Specifies an authorization user profile by its name. The profile-name argument is a case-sensitive string of 1 to 31 characters. The name can contain only letters, digits, and underscores (_). The user profile can begin with a letter or digit but it cannot be all digits. The user profile restricts the behavior of authenticated users. For more information, see Security Configuration Guide.

user-role role-name: Specifies an authorized user role. The role-name argument is a case-sensitive string of 1 to 63 characters. A maximum of 64 user roles can be specified for a user. For user role-related commands, see Fundamentals Command Reference for RBAC commands. This option is available only in local user view, and is not available in user group view.

vlan vlan-id: Specifies an authorized VLAN. The value range for the vlan-id argument is 1 to 4094. After passing authentication and being authorized a VLAN, a local user can access only the resources in this VLAN.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance to which the user belongs. The vpn-instance-name argument is a case-sensitive string of 1 to 31 characters. After passing authentication, the user has permission to access the network resources in the specified VPN.

work-directory directory-name: Specifies the working directory for FTP, SFTP, or SCP users. The directory-name argument is a case-insensitive string of 1 to 255 characters. The directory must already exist.

Usage guidelines

Configure authorization attributes according to the application environments and purposes. Support for authorization attributes depends on the service types of users.

For PPP users, only the following authorization attributes take effect: callback-number, idle-cut, ip, ip-pool, ipv6-pool, ipv6-prefix, primary-dns, secondary-dns, session-timeout, user-profile, vpn-instance, and url.

For portal users, only the following authorization attributes take effect: idle-cut, acl, ip-pool, ipv6-pool, user-profile, vpn-instance, and session-timeout.

For LAN users, only the following authorization attributes take effect: acl, idle-cut, session-timeout, user-profile, and vlan.

For SSH, Telnet, and terminal users, only the authorization attributes idle-cut and user-role take effect.

For HTTP and HTTPS users, only the authorization attribute user-role takes effect.

For FTP users, only the authorization attributes user-role and work-directory take effect.

For SSL VPN users, only the authorization attribute sslvpn-policy-group takes effect.

For IKE users, only the authorization attribute ip-pool takes effect.

For other types of local users, no authorization attribute takes effect.

Authorization attributes configured for a user group are intended for all local users in the group. You can group local users to improve configuration and management efficiency. An authorization attribute configured in local user view takes precedence over the same attribute configured in user group view.

For portal users to come online after passing authentication, make sure ACLs assigned to them do not have rules specified with a source IP or MAC address.

To make sure FTP, SFTP, and SCP users can access the directory after an active/standby switchover, do not specify chassis or slot information for the working directory.

To make sure the user have only the user roles authorized by using this command, use the undo authorization-attribute user-role command to remove the default user role.

The security-audit user role has access to the commands for managing security log files and security log file system. To display all the accessible commands of the security-audit user role, use the display role name security-audit command. For more information about security log management, see information center configuration in Network Management and Monitoring Configuration Guide. For more information about file system management, see Fundamentals Configuration Guide.

You cannot delete a local user if the local user is the only user that has the security-audit user role.

The security-audit user role is mutually exclusive with other user roles.

When you assign user roles to a user, the system prompts you to confirm the deletion of the user roles that are mutually exclusive with the new user roles.

Examples

# Configure the authorized VLAN of network access user abc as VLAN 2.

<Sysname> system-view

[Sysname] local-user abc class network

[Sysname-luser-network-abc] authorization-attribute vlan 2

# Configure the authorized VLAN of user group abc as VLAN 3.

<Sysname> system-view

[Sysname] user-group abc

[Sysname-ugroup-abc] authorization-attribute vlan 3

# Assign the security-audit user role to device management user xyz as the authorized user role.

<Sysname> system-view

[Sysname] local-user xyz class manage

[Sysname-luser-manage-xyz] authorization-attribute user-role security-audit

This operation will delete all other roles of the user. Are you sure? [Y/N]:y

Related commands

display local-user

display user-group

bind-attribute

Use bind-attribute to configure binding attributes for a local user.

Use undo bind-attribute to remove binding attributes of a local user.

Syntax

bind-attribute { call-number call-number [ : subcall-number ] | ip ip-address | location interface interface-type interface-number | mac mac-address | vlan vlan-id } *

undo bind-attribute { call-number | ip | location | mac | vlan } *

Default

No binding attributes are configured for a local user.

Views

Local user view

Predefined user roles

network-admin

mdc-admin

Parameters

call-number call-number: Specifies a calling number for PPP user authentication. The call-number argument is a string of 1 to 64 characters. This option applies only to PPP users.

subcall-number: Specifies the subcalling number. The total length of the calling number and the subcalling number cannot be more than 62 characters.

ip ip-address: Specifies the IP address to which the user is bound.

location interface interface-type interface-number: Specifies the interface to which the user is bound. The interface-type argument represents the interface type, and the interface-number argument represents the interface number. To pass authentication, the user must access the network through the bound interface. This option applies only to LAN, PPP, and portal users.

mac mac-address: Specifies the MAC address of the user in the format H-H-H. This option applies only to SSL VPN users that log in through iNode clients, LAN users, PPP users, and portal users.

vlan vlan-id: Specifies the VLAN to which the user belongs. The vlan-id argument is in the range of 1 to 4094. This option applies only to LAN, PPP, and portal users.

Usage guidelines

To perform local authentication of a user, the device matches the actual user attributes with the configured binding attributes. If the user has a non-matching attribute or lacks a required attribute, the user will fail authentication.

Binding attribute check takes effect on all access services. Configure the binding attributes for a user based on the access services and make sure the device can obtain all attributes to be checked from the user's packet.

When you configure the binding interface for portal users, specify the portal-enabled interface. Specify the Layer 2 Ethernet interface if portal is enabled on a VLAN interface and the portal roaming enable command is not configured.

Examples

# Bind MAC address 11-11-11 with network access user abc.

<Sysname> system-view

[Sysname] local-user abc class network

[Sysname-luser-network-abc] bind-attribute mac 11-11-11

Related commands

display local-user

company

Use company to specify the company of a local guest.

Use undo company to restore the default.

Syntax

company company-name

undo company

Default

No company is specified for a local guest.

Views

Local guest view

Predefined user roles

network-admin

mdc-admin

Parameters

company-name: Specifies the company name, a case-sensitive string of 1 to 255 characters.

Examples

# Specify company yyy for local guest abc.

<Sysname> system-view

[Sysname] local-user abc class network guest

[Sysname-luser-network(guest)-abc] company yyy

Related commands

display local-user

description

Use description to configure a description for a network access user.

Use undo description to restore the default.

Syntax

description text

undo description

Default

No description is configured for a network access user.

Views

Network access user view

Predefined user roles

network-admin

mdc-admin

Parameters

text: Configures a description, case-sensitive string of 1 to 127 characters.

Examples

# Configure a description for network access user 123.

<Sysname> system-view

[Sysname] local-user 123 class network

[Sysname-luser-network-123] description Manager of MSC company

Related commands

display local-user

display local-guest waiting-approval

Use display local-guest waiting-approval to display pending registration requests for local guests.

Syntax

display local-guest waiting-approval [ user-name user-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

user-name user-name: Specifies a local guest by the user name, a case-sensitive string of 1 to 55 characters. The user name must meet the following requirements:

· Cannot contain a domain name.

· Cannot contain any of the following characters: forward slash (/), backslash (\), vertical bar (|), colon (:), asterisk (*), question mark (?), left angle bracket (<), right angle bracket (>), and at sign (@).

· Cannot be a, al, or all.

If you do not specify a guest, this command displays pending registration requests for all local guests.

Usage guidelines

On the Web registration page, users submit local guest registration requests for approval. The guest manager can add supplementary information to the guest accounts and approves the requests. The device then creates local guest accounts based on the approved requests.

Examples

# Display all pending registration requests for local guests.

<Sysname> display local-guest waiting-approval

Total 1 guest informations matched.

Guest user Smith:

Full name : Smith Li

Company : YYY

Email : [email protected]

Phone : 139189301033

Description: The employee of YYY company

Table 2 Command output

Field	Description
Total 1 guest informations matched.	Number of local guests that have pending registration requests.
Full name	Full name of the local guest.
Company	Company name of the local guest.
Email	Email address of the local guest.
Phone	Phone number of the local guest.
Description	Description of the local guest.

Related commands

reset local-guest waiting-approval

display local-user

Use display local-user to display the local user configuration and online user statistics.

Syntax

display local-user [ class { manage | network [ guest ] } | idle-cut { disable | enable } | service-type { advpn | ftp | http | https | ike | lan-access | pad | portal | ppp | ssh | sslvpn | telnet | terminal } | state { active | block } | user-name user-name class { manage | network [ guest ] } | vlan vlan-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

class: Specifies the local user type.

manage: Device management user.

network: Network access user.

guest: Guest user account.

idle-cut { disable | enable }: Specifies local users by the status of the idle cut feature.

service-type: Specifies the local users that use a specific type of service.

advpn: ADVPN tunnel users.

ftp: FTP users.

http: HTTP users.

https: HTTPS users.

ike: IKE users that access the network through IKE extended authentication.

lan-access: LAN users that typically access the network through an Ethernet.

pad: X.25 PAD users.

portal: Portal users.

ppp: PPP users.

ssh: SSH users.

sslvpn: SSL VPN users.

telnet: Telnet users.

terminal: Terminal users that log in through console ports, AUX ports, or async ports.

state { active | block }: Specifies local users in active or blocked state. A local user in active state can access network services, but a local user in blocked state cannot.

user-name user-name: Specifies all local users using the specified username. The username must be a case-sensitive string of 1 to 55 characters. The name must meet the following requirements:

· Cannot contain the domain name.

· Cannot be a, al, or all.

vlan vlan-id: Specifies all local users in a VLAN. The vlan-id argument is in the range of 1 to 4094.

Usage guidelines

If you do not specify any parameters, this command displays information about all local users.

Examples

# Display information about all local users.

<Sysname> display local-user

Device management user root:

State: Active

Service type: SSH/Telnet/Terminal

Access limit: Enabled Max access number: 3

Current access number: 1

User group: system

Bind attributes:

Authorization attributes:

Work directory: flash:

User role list: network-admin

Password control configurations:

Password aging: 3 days

Network access user jj:

State: Active

Service type: LAN access

User group: system

Bind attributes:

IP address: 2.2.2.2

Location bound: GigabitEthernet2/0/1

MAC address: 0001-0001-0001

VLAN ID: 2

Authorization attributes:

Idle timeout: 33 minutes

Work directory: flash:

ACL number: 2000

User profile: pp

User role list: network-operator, level-0, level-3

SSL VPN policy group: spg

Description: A network access user

Validity period:

Start date and time: 2016/01/01-00:01:01

Expiration date and time:2019/01/01-01:01:01

Network access guest user user1:

State: Active

Service type: LAN access/Portal

User group: guest1

Full name: Jack

Company: cc

Email: [email protected]

Phone: 131129237

Description: A guest from company cc

Sponsor full name: Sam

Sponsor department: security

Sponsor email: [email protected]

Description: A guest from company cc

Validity period:

Start date and time: 2016/04/01-08:00:00

Expiration date and time:2019/04/03-18:00:00

Total 3 local users matched.

Table 3 Command output

Field	Description
State	Status of the local user: active or blocked.
Service type	Service types that the local user can use.
Access limit	Whether the concurrent login limit is enabled.
Max access number	Maximum number of concurrent logins using the local user name.
Current access number	Current number of concurrent logins using the local user name.
User group	Group to which the local user belongs.
Bind attributes	Binding attributes of the local user.
IP address	IP address of the local user.
Location bound	Binding port of the local user.
MAC address	MAC address of the local user.
VLAN ID	Binding VLAN of the local user.
Calling number	Calling number of the ISDN user.
Authorization attributes	Authorization attributes of the local user.
Idle timeout	Idle timeout period of the user, in minutes.
Session-timeout	Session timeout timer for the user, in minutes.
Callback number	Authorized PPP callback number of the local user.
Work directory	Directory that the FTP, SFTP, or SCP user can access.
ACL number	Authorization ACL of the local user.
VLAN ID	Authorized VLAN of the local user.
User profile	Authorization user profile of the local user.
User role list	Authorized roles of the local user.
IP pool	IPv4 address pool authorized to the local user.
SSL VPN policy group	SSL VPN policy group authorized to the local user.
IP address	IPv4 address authorized to the local user.
IPv6 address	IPv6 address authorized to the local user.
IPv6 prefix	IPv6 address prefix authorized to the local user.
IPv6 pool	IPv6 address pool authorized to the local user.
Primary DNS server	IPv4 address of the primary DNS server for the local user.
Secondary DNS server	IPv4 address of the secondary DNS server for the local user.
Primary DNSV6 server	IPv6 address of the primary DNS server for the local user.
Secondary DNSV6 server	IPv6 address of the secondary DNS server for the local user.
URL	Authorization PADM URL for the local user.
VPN instance	Authorization VPN instance for the local user.
Password control configurations	Password control attributes that are configured for the local user.
Password aging	Password expiration time.
Password length	Minimum number of characters that a password must contain.
Password composition	Password composition policy: · Minimum number of character types that a password must contain. · Minimum number of characters from each type in a password.
Password complexity	Password complexity checking policy: · Reject a password that contains the username or the reverse of the username. · Reject a password that contains any character repeated consecutively three or more times.
Maximum login attempts	Maximum number of consecutive failed login attempts.
Action for exceeding login attempts	Action to take on the user that failed to log in after using up all login attempts.
Password history was last reset	The most recent time that the history password records were cleared.
Full name	Name of the local guest.
Company	Company name of the local guest.
Email	Email address of the local guest.
Phone	Phone number of the local guest.
Sponsor full name	Name of the guest sponsor.
Sponsor department	Department of the guest sponsor.
Sponsor email	Email address of the guest sponsor.
Description	Description of the network access user.
Validity period	Validity period of the network access user.
Start date and time	Date and time from which the network access user begins to take effect.
Expiration date and time	Date and time at which the network access user expires.

‌

display user-group

Use display user-group to display user group configuration.

Syntax

display user-group { all | name group-name }

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

all: Specifies all user groups.

name group-name: Specifies a user group by its name, a case-insensitive string of 1 to 32 characters.

Examples

# Display the configuration of all user groups.

<Sysname> display user-group all

Total 2 user groups matched.

User group: system

Authorization attributes:

Work directory: flash:

User group: jj

Authorization attributes:

Idle timeout: 2 minutes

Callback number: 2:2

Work directory: flash:/

ACL number: 2000

VLAN ID: 2

User profile: pp

SSL VPN policy group: policygroup1

Password control configurations:

Password aging: 2 days

Table 4 Command output

Field	Description
User group	User group name.
Authorization attributes	Authorization attributes of the user group.
Idle timeout	Idle timeout period, in minutes.
Session-timeout	Session timeout timer, in minutes.
Callback number	Authorized PPP callback number.
Work directory	Directory that FTP, SFTP, or SCP users in the group can access.
ACL number	Authorization ACL.
VLAN ID	Authorized VLAN.
User profile	Authorization user profile.
IP pool	IPv4 address pool authorized to the user group.
SSL VPN policy group	SSL VPN policy group authorized to the user group.
IPv6 prefix	IPv6 address prefix authorized to the user group.
IPv6 pool	IPv6 address pool authorized to the user group.
Primary DNS server	IPv4 address of the primary DNS server authorized to the user group.
Secondary DNS server	IPv4 address of the secondary DNS server authorized to the user group.
Primary DNSV6 server	IPv6 address of the primary DNS server authorized to the user group.
Secondary DNSV6 server	IPv6 address of the secondary DNS server authorized to the user group.
URL	Authorization PADM URL for the user group.
VPN instance	Authorization VPN instance for the user group.
Password control configurations	Password control attributes that are configured for the user group.
Password aging	Password expiration time.
Password length	Minimum number of characters that a password must contain.
Password composition	Password composition policy: · Minimum number of character types that a password must contain. · Minimum number of characters from each type in a password.
Password complexity	Password complexity checking policy: · Reject a password that contains the username or the reverse of the username. · Reject a password that contains any character repeated consecutively three or more times.
Maximum login attempts	Maximum number of consecutive failed login attempts.
Action for exceeding login attempts	Action to take on the user that failed to log in after using up all login attempts.

‌

email

Use email to configure an email address for a local guest.

Use undo email to restore the default.

Syntax

email email-string

undo email

Default

No email address is configured for a local guest.

Views

Local guest view

Predefined user roles

network-admin

mdc-admin

Parameters

email-string: Specifies the email address for the local guest, a case-sensitive string of 1 to 255 characters. For example, [email protected]. The address must comply with RFC 822.

Usage guidelines

The local guest uses the email address to receive notifications from the device.

Examples

# Configure the email address as [email protected] for local guest abc.

<Sysname> system-view

[Sysname] local-user abc class network guest

[Sysname-luser-network(guest)-abc] email [email protected]

Related commands

display local-user

full-name

Use full-name to configure the name of a local guest.

Use undo full-name to restore the default.

Syntax

full-name name-string

undo full-name

Default

No name is configured for a local guest.

Views

Local guest view

Predefined user roles

network-admin

mdc-admin

Parameters

name-string: Specifies the local guest name, a case-sensitive string of 1 to 255 characters.

Examples

# Configure the name as abc Snow for local guest abc.

<Sysname> system-view

[Sysname] local-user abc class network guest

[Sysname-luser-network(guest)-abc] full-name abc Snow

Related commands

display local-user

group

Use group to assign a local user to a user group.

Use undo group to restore the default.

Syntax

group group-name

undo group

Default

A local user belongs to user group system.

Views

Local user view

Predefined user roles

network-admin

mdc-admin

Parameters

group-name: Specifies the user group name, a case-insensitive string of 1 to 32 characters.

Examples

# Assign device management user 111 to user group abc.

<Sysname> system-view

[Sysname] local-user 111 class manage

[Sysname-luser-manage-111] group abc

Related commands

display local-user

local-guest auto-delete enable

Use local-guest auto-delete enable to enable the guest auto-delete feature.

Use undo local-guest auto-delete enable to restore the default.

Syntax

local-guest auto-delete enable

undo local-guest auto-delete enable

Default

The guest auto-delete feature is disabled.

Views

System view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

This feature enables the device to automatically delete the local guest accounts when they expire.

Examples

# Enable the guest auto-delete feature.

<Sysname> system-view

[Sysname] local-guest auto-delete enable

Related commands

validity-datetime

local-guest email format

Use local-guest email format to configure the subject and body for the email notifications of local guest information.

Use undo local-guest email format to delete the configured subject or body for the email notifications of local guest information.

Syntax

local-guest email format to { guest | manager | sponsor } { body body-string | subject sub-string }

undo local-guest email format to { guest | manager | sponsor } { body | subject }

Default

No subject or body is configured for the email notifications of local guest information.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

to: Specifies the email recipient.

guest: Specifies the local guest.

manager: Specifies the guest manager.

sponsor: Specifies the guest sponsor.

body body-string: Configures the body content. The body-string argument is a case-sensitive string of 1 to 255 characters.

subject sub-string: Configures the email subject. The sub-string argument is a case-sensitive string of 1 to 127 characters.

Usage guidelines

Email notifications need to be sent to notify the local guests, guest sponsors, or guest managers of the guest account information or guest registration requests. Use this command to configure the subject and body for the email notifications to be sent by the device.

You can configure one subject and one body for each email recipient. If you configure the subject or body content multiple times for the same recipient, the most recent configuration takes effect.

You must configure both the subject and body for each recipient.

Examples

# Configure the subject and body for the email notifications to send to the local guest.

<Sysname> system-view

[Sysname] local-guest email format to guest subject Guest account information

[Sysname] local-guest email format to guest body A guest account has been created for you. The username, password, and validity period of the account are given below.

Related commands

local-guest email sender

local-guest email smtp-server

local-guest manager-email

local-guest send-email

local-guest email sender

Use local-guest email sender to configure the email sender address in email notifications of local guests sent by the device.

Use undo local-guest email sender to restore the default.

Syntax

local-guest email sender email-address

undo local-guest email sender

Default

No email sender address is configured for the email notifications of local guests sent by the device.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

email-address: Specifies the email sender address, a case-sensitive string of 1 to 255 characters.

Usage guidelines

If you do not specify the email sender address, the device cannot send email notifications.

The device supports only one email sender address. If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Specify the email sender address as [email protected] for email notifications of local guests.

<Sysname> system-view

[Sysname] local-guest email sender [email protected]

Related commands

local-guest email format

local-guest email smtp-server

local-guest manager-email

local-guest send-email

local-guest email smtp-server

Use local-guest email smtp-server to specify an SMTP server to send email notifications of local guests.

Use undo local-guest email smtp-server to restore the default.

Syntax

local-guest email smtp-server url-string

undo local-guest email smtp-server

Default

No SMTP server is specified to send email notifications of local guests.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

url-string: Specifies the path of the SMTP server, a case-sensitive string of 1 to 255 characters. The path must comply with the standard SMTP protocol and start with smtp://.

Usage guidelines

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Specify the SMTP server at smtp://www.test.com/smtp to send local guest email notifications.

<Sysname> system-view

[Sysname] local-guest email smtp-server smtp://www.test.com/smtp

Related commands

local-guest email format

local-guest email sender

local-guest manager-email

local-guest send-email

local-guest generate

Use local-guest generate to create local guests in batch.

Syntax

local-guest generate username-prefix name-prefix [ password-prefix password-prefix ] suffix suffix-number [ group group-name ] count user-count validity-datetime start-date start-time to expiration-date expiration-time

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

username-prefix name-prefix: Specifies the name prefix. The name-prefix argument is a case-sensitive string of 1 to 45 characters. The prefix cannot contain any of the following characters: forward slash (/), backslash (\), vertical bar (|), colon (:), asterisk (*), question mark (?), left angle bracket (<), right angle bracket (>), and at sign (@).

password-prefix password-prefix: Specifies a prefix for the plaintext password. The password-prefix argument is a case-sensitive string of 1 to 53 characters. If you do not specify a password prefix, the device randomly generates passwords for the local guests.

suffix suffix-number: Specifies the start suffix number of the username and password. The suffix-number argument is a numeric string of 1 to 10 digits.

group group-name: Specifies a user group by the name. The group-name argument is a case-sensitive string of 1 to 32 characters. If you do not specify a user group, the guests are assigned to the system-defined user group system.

count user-count: Specifies the number of local guests to be created. The value range for the user-count argument is 1 to 256.

validity-datetime: Specifies the validity period of the local guests. The expiration date and time must be later than the start date and time.

start-date: Specifies the start date of the validity period, in the format of MM/DD/YYYY or YYYY/MM/DD. The value range for the MM argument is 1 to 12. The value range for the DD argument varies with the specified month. The value range for the YYYY argument is 2000 to 2035.

start-time: Specifies the start time of the validity period, in the format of hh:mm:ss. The value range for the hh argument is 0 to 23. The value range for the mm and ss arguments is 0 to 59. The mm and ss arguments are optional. For example, enter 1 to indicate 1:00:00. A value of 0 indicates 00:00:00.

to: Specifies the end date and time of the validity period.

expiration-date: Specifies the expiration date in the format of MM/DD/YYYY or YYYY/MM/DD. The value range for the MM argument is 1 to 12. The value range for the DD argument varies with the specified month. The value range for the YYYY argument is 2000 to 2035.

expiration-time: Specifies the expiration time in the format of hh:mm:ss. The value range for the hh argument is 0 to 23. The value range for the mm and ss arguments is 0 to 59. The mm and ss arguments are optional. For example, enter 1 to indicate 1:00:00. A value of 0 indicates 00:00:00.

Usage guidelines

Account names of batch created local guests start with the same string specified by the name prefix, and end with a different number as the suffix. The system increases the start suffix number by 1 for each new local guest created in the batch.

The device generates plaintext passwords by using the password prefix and suffix number in the same way it batch creates the local guest names.

Consider the system resources when you specify the number of local guests to create. The device might fail to create all accounts for a large batch of local guests because of insufficient resources.

If a local guest to be created has the same name as an existing local guest on the device, the new guest overrides the existing guest.

Examples

# Create 20 local guests in batch with user names abc01 through abc20 for user group visit. The user accounts are effective from 2014/10/01 00:00:00 to 2015/10/02 12:00:00.

<Sysname> system-view

[Sysname] local-guest generate username-prefix abc suffix 01 group visit count 20 validity-datetime 2014/10/01 00:00:00 to 2015/10/02 12:00:00

Related commands

local-user

display local-user

local-guest manager-email

Use local-guest manager-email to configure the email address of the guest manager.

Use undo local-guest manager-email to restore the default.

Syntax

local-guest manager-email email-address

undo local-guest manager-email

Default

No email address is configured for the guest manager.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

email-address: Specifies the email address, a case-sensitive string of 1 to 255 characters. For example, [email protected]. The address must comply with RFC 822.

Usage guidelines

Use this command to specify the email address to which the device sends the local guest registration requests for approval.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Configure the email address of the guest manager as [email protected].

<Sysname> system-view

[Sysname] local-guest manager-email [email protected]

Related commands

local-guest email format

local-guest email sender

local-guest email smtp-server

local-guest send-email

Use local-guest send-email to send emails to a local guest or guest sponsor.

Syntax

local-guest send-email user-name user-name to { guest | sponsor }

Views

User view

Predefined user roles

network-admin

mdc-admin

Parameters

user-name user-name: Specifies a local guest by user name, a case-sensitive string of 1 to 55 characters. The name must meet the following requirements:

· Cannot contain a domain name.

· Cannot be a, al, or all.

to: Specifies the email recipient.

guest: Specifies the local guest.

sponsor: Specifies the guest sponsor.

Usage guidelines

Guest managers can use this command to inform local guests or guest sponsors of the guest password and validity period information.

Examples

# Send an email to notify local guest abc of the guest password and validity period information.

<Sysname> local-guest send-email user-name abc to guest

Related commands

sponsor-email

local-guest timer

Use local-guest timer to set the waiting-approval timeout timer for local guests.

Syntax

local-guest timer waiting-approval time-value

undo local-guest timer waiting-approval

Default

The setting is 24 hours.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

time-value: Specifies the waiting-approval timeout timer in the range of 1 to 720, in hours.

Usage guidelines

The waiting-approval timeout timer starts when the registration request of a local guest is sent for approval. If the request is not approved within the timer, the device deletes the registration request.

Examples

# Set the waiting-approval timeout timer to 12 hours.

<Sysname> system-view

[Sysname] local-guest timer waiting-approval 12

local-user

Use local-user to add a local user and enter its view, or enter the view of an existing local user.

Use undo local-user to delete local users.

Syntax

local-user user-name [ class { manage | network [ guest ] } ]

undo local-user { user-name class { manage | network [ guest ] } | all [ service-type { advpn | ftp | http | https | ike | lan-access | pad | portal | ppp | ssh | sslvpn | telnet | terminal } | class { manage | network [ guest ] } ] }

Default

No local users exist.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

user-name: Specifies the local user name, a case-sensitive string of 1 to 55 characters. The name must meet the following requirements:

· Cannot contain a domain name.

· Cannot be a, al, or all.

class: Specifies the local user type. If you do not specify this keyword, the command adds a device management user.

manage: Device management user that can configure and monitor the device after login. Device management users can use FTP, HTTP, HTTPS, Telnet, SSH, terminal, and PAD services.

network: Network access user that accesses network resources through the device. Network access users can use ADVPN, IKE, LAN access, portal, PPP, and SSL VPN services.

guest: Guest that can access network resources through the device during a specific validity period. Guests can use LAN access and portal services.

all: Specifies all users.

service-type: Specifies the local users that use a specific type of service.

advpn: ADVPN tunnel users.

ftp: FTP users.

http: HTTP users.

https: HTTPS users.

ike: IKE users that access the network through IKE extended authentication.

lan-access: LAN users that typically access the network through an Ethernet.

pad: X.25 PAD users.

portal: Portal users.

ppp: PPP users.

ssh: SSH users.

sslvpn: SSL VPN users.

telnet: Telnet users.

terminal: Terminal users that log in through console ports, AUX ports, or async ports.

Examples

# Add a device management user named user1 and enter local user view.

<Sysname> system-view

[Sysname] local-user user1 class manage

[Sysname-luser-manage-user1]

# Add a network access user named user2 and enter local user view.

<Sysname> system-view

[Sysname] local-user user2 class network

[Sysname-luser-network-user2]

# Add a local guest named user3 and enter local guest view.

Sysname> system-view

[Sysname] local-user user3 class network guest

[Sysname-luser-network(guest)-user3]

Related commands

display local-user

service-type (local user view)

local-user-export class network guest

Use local-user-export class network guest to export local guest account information to a .csv file in the specified path.

Syntax

local-user-export class network guest url url-string

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

url url-string: Specifies the URL of the destination file, a case-insensitive string of 1 to 255 characters.

Usage guidelines

You can import the user account information back to the device or to other devices that support the local-user-import network guest command. Before the import, you can edit the .csv file as needed. However, you must follow the restrictions in "local-user-import class network guest."

The device supports TFTP and FTP file transfer modes. Table 5 describes the valid URL formats of the .csv file.

Table 5 URL formats

Protocol	URL format	Description
TFTP	tftp://server/path/filename	Specify a TFTP server by IP address or hostname. For example, specify the file path as tftp://1.1.1.1/user/user.csv.
FTP	· With FTP user name and password: ftp://username:password@server/path/filename · Without FTP user name and password: ftp://server/path/filename	Specify an FTP server by IP address or hostname. The device ignores the domain name in the FTP user name. For example, specify the file path as ftp://1:[email protected]/user/user.csv or ftp://1.1.1.1/user/user.csv.

Protocol

URL format

Description

TFTP

tftp://server/path/filename

Specify a TFTP server by IP address or hostname. For example, specify the file path as tftp://1.1.1.1/user/user.csv.

FTP

· With FTP user name and password:
ftp://username:password@server/path/filename

· Without FTP user name and password:
ftp://server/path/filename

Specify an FTP server by IP address or hostname.

The device ignores the domain name in the FTP user name.

For example, specify the file path as ftp://1:[email protected]/user/user.csv or ftp://1.1.1.1/user/user.csv.

Examples

# Export local guest account information to the guest.csv file in the ftp://1.1.1.1/user/ path.

<Sysname> system-view

[Sysname] local-user-export class network guest url ftp://1.1.1.1/user/guest.csv

Related commands

display local-user

local-user-import class network guest

Use local-user-import class network guest to import local guest account information from a .csv file in the specified path to the device to create local guests based on the imported information.

Syntax

local-user-import class network guest url url-string validity-datetime start-date start-time to expiration-date expiration-time [ auto-create-group | override | start-line line-number ] *

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

url url-string: Specifies the source file path. The url-string argument is a case-insensitive string of 1 to 255 characters.

validity-datetime: Specifies the guest validity period of the local guests. The expiration date and time must be later than the start date and time.

to: Specifies the end date and time of the validity period.

auto-create-group: Enables the device to automatically create user groups for the imported local guests if the groups in the imported information do not exist on the device. If you do not specify this keyword, the device adds all imported local guests to the system-defined user group named system.

override: Enables the device to override the existing account with the same name as an imported guest account. If you do not specify this keyword, the device retains the existing account and does not import the local guest with the same name.

start-line line-number: Specifies the number of the line at which the account import begins. If you do not specify a line number, this command imports all accounts in the .csv file.

Usage guidelines

The .csv file contains multiple parameters for each account and the parameters must be strictly arranged in the following order:

· Username—User name of the guest account. The user name cannot be empty. The user name cannot be empty and cannot contain any of the following characters: forward slash (/), backslash (\), vertical bar (|), colon (:), asterisk (*), question mark (?), left angle bracket (<), right angle bracket (>), or at sign (@). The name cannot be a, al, or all. Any invalid character results in account import failure and interruption.

· Password—Password of the guest account in plaintext form. If the password is empty, the device generates a random password in encrypted form for the guest.

· User group—User group to which the guest belongs. If the user group is empty, the device assigns the guest to the system-defined user group named system.

· Guest full name—Name of the guest.

· Guest company—Company of the guest.

· Guest email—Email address of the guest.

· Guest phone—Phone number of the guest.

· Guest description—Description of the guest.

· Sponsor full name—Name of the guest sponsor.

· Sponsor department—Department of the guest sponsor.

· Sponsor email—Email address of the guest sponsor.

The value of each parameter in the file must meet the requirements of the local user attributes on the device. Any violation results in account import failure and interruption. The system displays the number of the line where the account import is interrupted.

Separate different account entries by a carriage return and separate each parameter value in an account entry by a comma (,). If the value of a parameter contains a comma (,), you must enclose the value within a pair of quotation marks ("") to avoid ambiguity. For example,

Jack,abc,visit,Jack Chen,ETP,[email protected],1399899,"The manager of ETP, come from TP.",Sam Wang,Ministry of personnel,[email protected]

The device supports TFTP and FTP file transfer modes. Table 6 describes the valid URL formats of the .csv file.

Table 6 URL formats

Protocol	URL format	Description
TFTP	tftp://server/path/filename	Specify a TFTP server by IP address or hostname. For example, specify the file path as tftp://1.1.1.1/user/user.csv.
FTP	· With FTP user name and password: ftp://username:password@server/path/filename · Without FTP user name and password: ftp://server/path/filename	Specify an FTP server by IP address or hostname. The device ignores the domain name in the FTP user name. For example, specify the file path as ftp://1:[email protected]/user/user.csv or ftp://1.1.1.1/user/user.csv.

Protocol

URL format

Description

TFTP

tftp://server/path/filename

Specify a TFTP server by IP address or hostname. For example, specify the file path as tftp://1.1.1.1/user/user.csv.

FTP

· With FTP user name and password:
ftp://username:password@server/path/filename

· Without FTP user name and password:
ftp://server/path/filename

Specify an FTP server by IP address or hostname.

The device ignores the domain name in the FTP user name.

For example, specify the file path as ftp://1:[email protected]/user/user.csv or ftp://1.1.1.1/user/user.csv.

Examples

# Import guest account information from the ftp://1.1.1.1/user/guest.csv file and specify a validity period for the imported guests.

<Sysname> system-view

[Sysname] local-user-import class network guest url ftp://1.1.1.1/user/guest.csv validity-datetime 2014/10/01 00:00:00 to 2014/10/02 12:00:00

Related commands

display local-user

local-user-export class network guest

password (device management user view)

Use password to configure a password for a device management user.

Use undo password to restore the default.

Syntax

In non-FIPS mode:

password [ { hash | simple } string ]

undo password

In FIPS mode:

password

Default

In non-FIPS mode:

A device management user does not have a password and can pass authentication after entering the correct username and passing attribute checks.

In FIPS mode:

A device management user does not have a password and cannot pass authentication.

Views

Device management user view

Predefined user roles

network-admin

mdc-admin

Parameters

hash: Specifies a password encrypted by the hash algorithm.

simple: Specifies a password in plaintext form. For security purposes, the password specified in plaintext form will be stored in encrypted form.

string: Specifies the password string. This argument is case sensitive. In non-FIPS mode, the hashed form of the password is a string of 1 to 110 characters. The plaintext form of the password is a string of 1 to 63 characters. In FIPS mode, the password is in plaintext form and is a string of 15 to 63 characters. The string must contain digits, uppercase letters, lowercase letters, and special characters.

Usage guidelines

If you do not specify any parameters, you enter the interactive mode to set a plaintext password.

In non-FIPS mode, a device management user for which no password is specified can pass authentication after entering the correct username and passing attribute checks. To enhance security, configure a password for each device management user.

In FIPS mode, a password is required for a device management user to pass authentication. You must set the password in interactive mode.

Examples

# Set the password to 123456TESTplat&! in plaintext form for device management user user1.

<Sysname> system-view

[Sysname] local-user user1 class manage

[Sysname-luser-manage-user1] password simple 123456TESTplat&!

# Configure the password in interactive mode for device management user test.

<Sysname> system-view

[Sysname] local-user test class manage

[Sysname-luser-manage-test] password

Password:

confirm :

Related commands

display local-user

password (network access user view)

Use password to configure a password for a network access user.

Use undo password to restore the default.

Syntax

password { cipher | simple } string

undo password

Default

A network access user does not have a password and can pass authentication after entering the correct username and passing attribute checks.

Views

Network access user view

Predefined user roles

network-admin

mdc-admin

Parameters

cipher: Specifies a password in encrypted form.

simple: Specifies a password in plaintext form. For security purposes, the password specified in plaintext form will be stored in encrypted form.

string: Specifies the password string. Its plaintext form is a case-sensitive string of 1 to 63 characters. Its encrypted form is a case-sensitive string of 1 to 117 characters.

Usage guidelines

As a best practice to enhance security, configure a password for each network access user.

Examples

# Set the password to 123456TESTuser&! in plaintext form for network access user user1.

<Sysname> system-view

[Sysname] local-user user1 class network

[Sysname-luser-network-user1] password simple 123456TESTuser&!

Related commands

display local-user

phone

Use phone to specify the phone number of a local guest.

Use undo phone to restore the default.

Syntax

phone phone-number

undo phone

Default

No phone number is specified for a local guest.

Views

Local guest view

Predefined user roles

network-admin

mdc-admin

Parameters

phone-number: Specifies the phone number, a string of 1 to 32 characters.

Examples

# Specify the phone number as 13813723920 for local guest abc.

<Sysname> system-view

[Sysname] local-user abc class network guest

[Sysname-luser-network(guest)-abc] phone 13813723920

Related commands

display local-user

reset local-guest waiting-approval

Use reset local-guest waiting-approval to clear pending registration requests for local guests.

Syntax

reset local-guest waiting-approval [ user-name user-name ]

Views

User view

Predefined user roles

network-admin

mdc-admin

Parameters

user-name user-name: Specifies a local guest by the user name, a case-sensitive string of 1 to 55 characters. The user name must meet the following requirements:

· Cannot contain a domain name.

· Cannot be a, al, or all.

If you do not specify a guest, this command clears information about all registration requests for local guests.

Examples

# Clear information about all registration requests for local guests.

<Sysname> reset local-guest waiting-approval

Related commands

display local-guest waiting-approval

service-type (local user view)

Use service-type to specify the service types that a local user can use.

Use undo service-type to remove service types configured for a local user.

Syntax

In non-FIPS mode:

service-type { advpn | ftp | ike | lan-access | { http | https | pad | ssh | telnet | terminal } * | portal | ppp | sslvpn }

undo service-type { advpn | ftp | ike | lan-access | { http | https | pad | ssh | telnet | terminal } * | portal | ppp | sslvpn }

In FIPS mode:

service-type { advpn | ike | lan-access | { https | pad | ssh | terminal } * | portal | ppp | sslvpn }

undo service-type { advpn | ike | lan-access | { https | pad | ssh | terminal } * | portal | ppp | sslvpn }

Default

A local user is not authorized to use any service.

Views

Local user view

Predefined user roles

network-admin

mdc-admin

Parameters

advpn: Authorizes the user to use the ADVPN service.

ftp: Authorizes the user to use the FTP service. The authorized directory can be modified by using the authorization-attribute work-directory command.

http: Authorizes the user to use the HTTP service.

https: Authorizes the user to use the HTTPS service.

ike: Authorizes the user to use the IKE extended authentication service.

lan-access: Authorizes the user to use the LAN access service. The users are typically Ethernet users.

pad: Authorizes the user to use the PAD service.

ssh: Authorizes the user to use the SSH service.

telnet: Authorizes the user to use the Telnet service.

terminal: Authorizes the user to use the terminal service and log in from a console, AUX, or async port.

portal: Authorizes the user to use the portal service.

ppp: Authorizes the user to use the PPP service.

sslvpn: Authorizes the user to use the SSL VPN service.

Usage guidelines

You can assign multiple service types to a user.

Examples

# Authorize device management user user1 to use the Telnet and FTP services.

<Sysname> system-view

[Sysname] local-user user1 class manage

[Sysname-luser-manage-user1] service-type telnet

[Sysname-luser-manage-user1] service-type ftp

Related commands

display local-user

sponsor-department

Use sponsor-department to specify the department of the guest sponsor for a local guest.

Use undo sponsor-department to restore the default.

Syntax

sponsor-department department-string

undo sponsor-department

Default

No department is specified for the guest sponsor of a local guest.

Views

Local guest view

Predefined user roles

network-admin

mdc-admin

Parameters

department-string: Specifies the department name, a case-sensitive string of 1 to 127 characters.

Examples

# Specify the department as test for the guest sponsor of local guest abc.

<Sysname> system-view

[Sysname] local-user abc class network guest

[Sysname-luser-network(guest)-abc] sponsor-department test

Related commands

display local-user

sponsor-email

Use sponsor-email to specify the email address of the guest sponsor for a local guest.

Use undo sponsor-email to restore the default.

Syntax

sponsor-email email-string

undo sponsor-email

Default

No email address is specified for the guest sponsor.

Views

Local guest view

Predefined user roles

network-admin

mdc-admin

Parameters

email-string: Specifies the email address, a case-sensitive string of 1 to 255 characters. The address must comply with RFC 822.

Examples

# Specify the email address as [email protected] for the guest sponsor of local guest abc.

<Sysname> system-view

[Sysname] local-user abc class network guest

[Sysname-luser-network(guest)-abc] sponsor-email [email protected]

Related commands

display local-user

sponsor-full-name

Use sponsor-full-name to specify the guest sponsor name for a local guest.

Use undo sponsor-full-name to restore the default.

Syntax

sponsor-full-name name-string

undo sponsor-full-name

Default

No guest sponsor name is specified for a local guest.

Views

Local guest view

Predefined user roles

network-admin

mdc-admin

Parameters

name-string: Specifies the guest sponsor name, a case-sensitive string of 1 to 255 characters.

Examples

# Specify the guest sponsor name as Sam Li for local guest abc.

<Sysname> system-view

[Sysname] local-user abc class network guest

[Sysname-luser-network(guest)-abc] sponsor-full-name Sam Li

Related commands

display local-user

state (local user view)

Use state to set the status of a local user.

Use undo state to restore the default.

Syntax

state { active | block }

undo state

Default

A local user is in active state.

Views

Local user view

Predefined user roles

network-admin

mdc-admin

Parameters

active: Places the local user in active state to allow the local user to request network services.

block: Places the local user in blocked state to prevent the local user from requesting network services.

Examples

# Place device management user user1 in blocked state.

<Sysname> system-view

[Sysname] local-user user1 class manage

[Sysname-luser-manage-user1] state block

Related commands

display local-user

user-group

Use user-group to create a user group and enter its view, or enter the view of an existing user group.

Use undo user-group to delete a user group.

Syntax

user-group group-name

undo user-group group-name

Default

A system-defined user group exists. The group name is system.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

group-name: Specifies the user group name, a case-insensitive string of 1 to 32 characters.

Usage guidelines

A user group consists of a group of local users and has a set of local user attributes. You can configure local user attributes for a user group to implement centralized management of user attributes for the local users in the group.

You cannot use the undo user-group command to delete a user group that has local users.

You can modify settings for the system-defined user group named system, but you cannot delete the user group.

Examples

# Create a user group named abc and enter user group view.

<Sysname> system-view

[Sysname] user-group abc

[Sysname-ugroup-abc]

Related commands

display user-group

validity-datetime

Use validity-datetime to specify the validity period for a local user.

Use undo validity-datetime to restore the default.

Syntax

In network access user view (except for local guest view):

validity-datetime { from start-date start-time to expiration-date expiration-time | from start-date start-time | to expiration-date expiration-time }

undo validity-datetime

In local guest view:

validity-datetime from start-date start-time to expiration-date expiration-time

undo validity-datetime

Default

The validity period for a local user does not expire.

Views

Network access user view

Local guest view

Predefined user roles

network-admin

mdc-admin

Parameters

from: Specifies the validity start date and time for the user. If you do not specify this option, the command defines only the expiration date and time of the user.

start-date: Specifies the date on which the user becomes effective. The date is in the format of MM/DD/YYYY or YYYY/MM/DD. The value range for the MM argument is 1 to 12. The value range for the DD argument varies with the specified month. The value range for the YYYY argument is 2000 to 2035.

start-time: Specifies the time on the day when the user becomes effective. The time is in the format of hh:mm:ss. The value range for the hh argument is 0 to 23. The value range for the mm and ss arguments is 0 to 59. The mm and ss arguments are optional. For example, enter 1 to indicate 1:00:00. A value of 0 indicates 00:00:00.

to: Specifies the expiration date and time for the user. If you do not specify this option, the command defines only the validity start date and time of the user.

Usage guidelines

Expired user accounts cannot be used for authentication.

When both from and to options are specified, the expiration date and time must be later than the validity start date and time.

When only the from option is specified, the user is valid since the specified date and time.

When only the to option is specified, the user is valid until the specified date and time.

Examples

# Specify the validity period for user 123.

<Sysname> system-view

[Sysname] local-user 123 class network

[Sysname-luser-network-123] validity-datetime from 2015/10/01 00:00:00 to 2018/10/02 12:00:00

Related commands

display local-user

RADIUS commands

aaa device-id

Use aaa device-id to configure the device ID.

Use undo aaa device-id to restore the default.

Syntax

aaa device-id device-id

undo aaa device-id

Default

The device ID is 0.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

device-id: Specifies a device ID in the range of 1 to 255.

Usage guidelines

RADIUS uses the value of the Acct-Session-ID attribute as the accounting ID for a user. The device generates an Acct-Session-ID value that includes the device ID for each online user.

If you modify the device ID, the new device ID does not take effect on users that have been online during the change.

Examples

# Configure the device ID as 1.

<Sysname> system-view

[Sysname] aaa device-id 1

accounting-on enable

Use accounting-on enable to configure the accounting-on feature.

Use undo accounting-on enable to disable the accounting-on feature.

Syntax

accounting-on enable [ interval interval | send send-times ] *

undo accounting-on enable

Default

The accounting-on feature is disabled.

Views

RADIUS scheme view

Predefined user roles

network-admin

mdc-admin

Parameters

interval interval: Specifies the time interval for retransmitting an accounting-on packet in seconds. The value range for the interval argument is 1 to 15, and the default setting is 3.

send send-times: Specifies the maximum number of accounting-on packet transmission attempts. The value range for the send-times argument is 1 to 255, and the default setting is 50.

Usage guidelines

The accounting-on feature enables the device to automatically send an accounting-on packet to the RADIUS server after a device reboot. Upon receiving the accounting-on packet, the RADIUS server logs out all online users so they can log in again through the device.

Execute the save command to ensure that the accounting-on enable command takes effect at the next device reboot. For information about the save command, see Fundamentals Command Reference.

Parameters set by using the accounting-on enable command take effect immediately.

Examples

# Enable the accounting-on feature for RADIUS scheme radius1, and set the retransmission interval to 5 seconds and the transmission attempts to 15.

<Sysname> system-view

[Sysname] radius scheme radius1

[Sysname-radius-radius1] accounting-on enable interval 5 send 15

Related commands

display radius scheme

accounting-on extended

Use accounting-on extended to enable the extended accounting-on feature.

Use undo accounting-on extended to disable the extended accounting-on feature.

Syntax

accounting-on extended

undo accounting-on extended

Default

The extended accounting-on feature is disabled.

Views

RADIUS scheme view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Usage guidelines

The extended accounting-on feature enhances the accounting-on feature by applying to a distributed architecture. For the extended accounting-on feature to take effect, the RADIUS server must run on IMC and the accounting-on feature must be enabled.

The extended accounting-on feature is applicable to LAN and PPP (L2TP LAC-side) users. The user data is saved to the cards through which the users access the device.

When this feature is enabled, the device automatically sends an accounting-on packet to the RADIUS server after a card reboots (device not reboot). The packet contains the card identifier. Upon receiving the accounting-on packet, the RADIUS server logs out all online users that access the device through the card. If no users have come online through the card, the device does not send an accounting-on packet to the RADIUS server after the card reboots.

The device uses the packet retransmission interval and maximum transmission attempts set by using the accounting-on enable command for this feature.

Execute the save command to ensure that the accounting-on extended command takes effect at the next card reboot. For information about the save command, see Fundamentals Command Reference.

Examples

# Enable the extended accounting-on feature for RADIUS scheme radius1.

<Sysname> system-view

[Sysname] radius scheme radius1

[Sysname-radius-radius1] accounting-on extended

Related commands

accounting-on enable

display radius scheme

attribute 15 check-mode

Use attribute 15 check-mode to configure the Login-Service attribute check method for SSH, FTP, and terminal users.

Use undo attribute 15 check-mode to restore the default.

Syntax

attribute 15 check-mode { loose | strict }

undo attribute 15 check-mode

Default

The strict check method applies for SSH, FTP, and terminal users.

Views

RADIUS scheme view

Predefined user roles

network-admin

mdc-admin

Parameters

loose: Matches the standard Login-Service attribute value 0 for SSH, FTP, and terminal services.

strict: Matches Login-Service attribute values 50, 51, and 52 for SSH, FTP, and terminal services, respectively.

Usage guidelines

Use the loose check method only when the server does not issue Login-Service attribute values 50, 51, and 52 for SSH, FTP, and terminal users.

Examples

# Configure the Login-Service attribute check method as loose for SSH, FTP, and terminal users in RADIUS scheme radius1.

<Sysname> system-view

[Sysname] radius scheme radius1

[Sysname-radius-radius1] attribute 15 check-mode loose

Related commands

display radius scheme

attribute 17 old-password

Use attribute 17 old-password to enable online user password change by using RADIUS attribute 17.

Use undo attribute 17 old-password to restore the default.

Syntax

attribute 17 old-password

undo attribute 17 old-password

Default

Online user password change is disabled.

Views

RADIUS scheme view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

This feature enables the device to cooperate with the RADIUS authentication server to allow users to change their passwords online. With online user password change enabled, the device sends a RADIUS authentication request to the RADIUS server upon receiving a password change request from an online user. In the authentication request, the device carries the new user password in RADIUS attribute 2 and the old user password in RADIUS attribute 17. If the device receives a response from the RADIUS server, the online user's password is changed successfully.

This feature is applicable only to SSL VPN users.

Do not enable this feature if the RADIUS server does not support online user password change.

Examples

# In RADIUS scheme radius1, enable online user password change by using RADIUS attribute 17.

<Sysname> system-view

[Sysname] radius scheme radius1

[Sysname-radius-radius1] attribute 17 old-password

Related commands

display radius scheme

attribute 25 car

Use attribute 25 car to configure the device to interpret the RADIUS class attribute (attribute 25) as CAR parameters.

Use undo attribute 25 car to restore the default.

Syntax

attribute 25 car

undo attribute 25 car

Default

The RADIUS class attribute is not interpreted as CAR parameters.

Views

RADIUS scheme view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

Configure the device to interpret the RADIUS class attribute if the RADIUS server uses the attribute to deliver CAR parameters for user-based traffic monitoring and control.

Examples

# In RADIUS scheme radius1, configure the device to interpret the RADIUS class attribute as CAR parameters.

<Sysname> system-view

[Sysname] radius scheme radius1

[Sysname-radius-radius1] attribute 25 car

Related commands

display radius scheme

attribute convert (RADIUS DAS view)

Use attribute convert to configure a RADIUS attribute conversion rule.

Use undo attribute convert to delete RADIUS attribute conversion rules.

Syntax

attribute convert src-attr-name to dest-attr-name { { coa-ack | coa-request } * | { received | sent } * }

undo attribute convert [ src-attr-name ]

Default

No RADIUS attribute conversion rules exist. The system processes RADIUS attributes according to the principles of the standard RADIUS protocol.

Views

RADIUS DAS view

Predefined user roles

network-admin

mdc-admin

Parameters

src-attr-name: Specifies the source RADIUS attribute by its name, a case-insensitive string of 1 to 63 characters. The attribute must be supported by the system.

dest-attr-name: Specifies the destination RADIUS attribute by its name, a case-insensitive string of 1 to 63 characters. The attribute must be supported by the system.

coa-ack: Specifies the CoA acknowledgment packets.

coa-request: Specifies the CoA request packets.

received: Specifies the received DAE packets.

sent: Specifies the sent DAE packets.

Usage guidelines

The device replaces the attribute in packets that match a RADIUS attribute conversion rule with the destination RADIUS attribute in the rule.

The conversion rules take effect only when the RADIUS attribute translation feature is enabled.

When you configure RADIUS attribute conversion rules, follow these restrictions and guidelines:

· The source and destination RADIUS attributes in a rule must use the same data type.

· The source and destination RADIUS attributes in a rule cannot use the same name.

· A source RADIUS attribute can be converted only by one criterion, packet type or direction.

· One source RADIUS attribute cannot be converted to multiple destination attributes.

If you do not specify a source RADIUS attribute, the undo attribute convert command deletes all RADIUS attribute conversion rules.

Examples

# In RADIUS DAS view, configure a RADIUS attribute conversion rule to replace the Hw-Server-String attribute in the received DAE packets with the Connect-Info attribute.

<Sysname> system-view

[Sysname] radius dynamic-author server

[Sysname-radius-da-server] attribute convert Hw-Server-String to Connect-Info received

Related commands

attribute translate

attribute convert (RADIUS scheme view)

Use attribute convert to configure a RADIUS attribute conversion rule.

Use undo attribute convert to delete RADIUS attribute conversion rules.

Syntax

attribute convert src-attr-name to dest-attr-name { { access-accept | access-request | accounting } * | { received | sent } * }

undo attribute convert [ src-attr-name ]

Default

No RADIUS attribute conversion rules exist. The system processes RADIUS attributes according to the principles of the standard RADIUS protocol.

Views

RADIUS scheme view

Predefined user roles

network-admin

mdc-admin

Parameters

src-attr-name: Specifies the source RADIUS attribute by its name, a case-insensitive string of 1 to 63 characters. The attribute must be supported by the system.

dest-attr-name: Specifies the destination RADIUS attribute by its name, a case-insensitive string of 1 to 63 characters. The attribute must be supported by the system.

access-accept: Specifies the RADIUS Access-Accept packets.

access-request: Specifies the RADIUS Access-Request packets.

accounting: Specifies the RADIUS accounting packets.

received: Specifies the received RADIUS packets.

sent: Specifies the sent RADIUS packets.