The expected bandwidth is an informational parameter used only by higher-layer protocols for calculation. You cannot adjust the actual bandwidth of an interface by using this command.

Examples

# Set the expected bandwidth to 10000 kbps for VLAN-interface 1.

<Sysname> system-view

[Sysname] interface vlan-interface 1

[Sysname-Vlan-interface1] bandwidth 10000

default

Use default to restore the default settings for a VLAN interface.

Syntax

default

Views

VLAN interface view

Predefined user roles

network-admin

Usage guidelines

CAUTION:

The default command might interrupt ongoing network services. Make sure you are fully aware of the impact of this command when you use it on a live network.

‌

This command might fail to restore the default settings for some commands for reasons such as command dependencies or system restrictions. Use the display this command in interface view to identify these commands, and then use their undo forms or follow the command reference to restore their default settings. If your restoration attempt still fails, follow the error message instructions to resolve the problem.

Examples

# Restore the default settings for VLAN-interface 1.

<Sysname> system-view

[Sysname] interface vlan-interface 1

[Sysname-Vlan-interface1] default

description

Use description to configure the description of a VLAN or VLAN interface.

Use undo description to restore the default.

Syntax

description text

undo description

Default

For a VLAN, the description is VLAN vlan-id. The vlan-id argument specifies the VLAN ID in a four-digit format. If the VLAN ID has fewer than four digits, leading zeros are added. For example, the default description of VLAN 100 is VLAN 0100.

For a VLAN interface, the description is the name of the interface. For example, Vlan-interface1 Interface.

Views

VLAN view

VLAN interface view

Predefined user roles

network-admin

Parameters

text: Specifies a description, a case-sensitive string of 1 to 255 characters.

Usage guidelines

To manage VLANs and VLAN interfaces efficiently, configure descriptions for them based on their functions or connections.

Examples

# Configure the description of VLAN 2 as sales-private.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2] description sales-private

# Configure the description of VLAN-interface 2 as linktoPC56.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2] quit

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] description linktoPC56

Related commands

display interface vlan-interface

display vlan

display interface vlan-interface

Use display interface vlan-interface to display VLAN interface information.

Syntax

display interface [ vlan-interface [ interface-number ] ] [ brief [ description | down ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vlan-interface interface-number: Specifies a VLAN interface number. If you do not specify this option, the command displays information about all interfaces except VA interfaces. If you specify the vlan-interface keyword without specifying an interface, the command displays information about all VLAN interfaces. For more information about VA interfaces, see PPP in Layer 2—WAN Access Configuration Guide.

brief: Displays brief interface information. If you do not specify this keyword, the command displays detailed interface information.

description: Displays complete interface descriptions. If you do not specify this keyword, the command displays only the first 27 characters of each interface description.

down: Displays VLAN interfaces in down state and their down causes. If you do not specify this keyword, the command displays information about VLAN interfaces in all states.

Examples

# Display information about VLAN-interface 2.

<Sysname> display interface vlan-interface 2

Vlan-interface2

Current state: DOWN

Line protocol state: DOWN

Description: Vlan-interface2 Interface

Bandwidth: 1000000 kbps

Maximum transmission unit: 1500

Internet protocol processing : Disabled

IP packet frame type: Ethernet II, hardware address: 000f-e249-8050

IPv6 packet frame type: Ethernet II, hardware address: 000f-e249-8050

Output queue - Urgent queuing: Size/Length/Discards 0/1024/0

Output queue - Protocol queuing: Size/Length/Discards 0/500/0

Output queue - FIFO queuing: Size/Length/Discards 0/75/0

Last clearing of counters: Never

Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Input: 0 packets, 0 bytes, 0 drops

Output: 0 packets, 0 bytes, 0 drops

# Display brief information about VLAN-interface 2.

<Sysname> display interface vlan-interface 2 brief

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface Link Protocol Primary IP Description

Vlan2 DOWN DOWN --

Table 1 Command output

Field	Description
Vlan-interface2	VLAN interface name.
Current state	Physical link state of the VLAN interface: · Administratively DOWN—The interface has been shut down by using the shutdown command. · DOWN—The interface is administratively up, but its physical state is down. The VLAN of this VLAN interface does not contain any physical ports in up state. The ports might not be connected correctly or the links might have failed. · UP—The interface is both administratively and physically up.
Line protocol state	Data link layer state of the VLAN interface: · DOWN—The link layer protocol state of the interface is down. · UP—The link layer protocol state of the interface is up.
Description	Description of the VLAN interface.
Bandwidth	Expected bandwidth of the VLAN interface.
Maximum transmission unit	MTU of the VLAN interface.
Internet protocol processing : Disabled	The VLAN interface is not assigned an IP address and cannot process IP packets.
IP packet frame type	IPv4 packet framing format.
hardware address	MAC address of the VLAN interface.
IPv6 packet frame type	IPv6 packet framing format.
Output queue - Urgent queuing: Size/Length/Discards 0/1024/0 Output queue - Protocol queuing: Size/Length/Discards 0/500/0 Output queue - FIFO queuing: Size/Length/Discards 0/75/0	Information about the urgent, protocol, and FIFO output queues: · Size—Number of packets in the queue. · Length—Maximum number of packets that the queue can contain. · Discards—Number of dropped packets.
Last clearing of counters	The most recent time that the reset counters interface vlan-interface command was executed. This field displays Never if you have never executed this command.
Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec	Average rates of input packets and output packets in the last 300 seconds (in Bps, bps, and pps).
Input: 0 packets, 0 bytes, 0 drops	Total number and size (in bytes) of the received packets of the interface and the number of the dropped packets.
Output: 0 packets, 0 bytes, 0 drops	Total number and size (in bytes) of the sent packets of the interface and the number of the dropped packets.
Brief information on interfaces in route mode	Brief information about Layer 3 interfaces.
Interface	Abbreviated interface name.
Link	Physical link state of the interface: · UP—The interface is physically up. · DOWN—The interface is physically down. · ADM—The interface has been shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command. · Stby—The interface is a backup interface in standby state. To see the primary interface, use the display interface-backup state command.
Protocol	Data link layer protocol state of the interface: · UP—The data link layer protocol state of the interface is up. · DOWN—The data link layer protocol state of the interface is down. · UP(s)—The data link layer protocol of the interface is up, but the link is an on-demand link or does not exist. The (s) attribute represents the spoofing flag.
Primary IP	Primary IP address of the interface.

‌

Related commands

reset counters interface vlan-interface

display vlan

Use display vlan to display VLAN information.

Syntax

display vlan [ vlan-id1 [ to vlan-id2 ] | all | dynamic | static ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vlan-id1: Specifies a VLAN by its ID in the range of 1 to 4094.

vlan-id1 to vlan-id2: Specifies a VLAN ID range. Both the vlan-id1 and the vlan-id2 arguments are in the range of 1 to 4094. The value for the vlan-id2 argument must be equal to or greater than the value for the vlan-id1 argument.

all: Specifies all VLANs except the reserved VLANs.

dynamic: Specifies dynamic VLANs. If you specify this keyword, the command displays the total number of dynamic VLANs and each dynamic VLAN ID. Dynamic VLANs are generated through MVRP or assigned by a RADIUS server.

static: Specifies static VLANs. If you specify this keyword, the command displays the total number of static VLANs and each static VLAN ID. Static VLANs are manually created.

Examples

# Display information about VLAN 2.

<Sysname> display vlan 2

VLAN ID: 2

VLAN type: Static

Route interface: Not configured

Description: VLAN 0002

Name: VLAN 0002

Tagged ports: None

Untagged ports:

GigabitEthernet1/0/1 GigabitEthernet1/0/2 GigabitEthernet1/0/3

# Display information about VLAN 3.

<Sysname> display vlan 3

VLAN ID: 3

VLAN type: static

Route interface: Configured

IPv4 address: 1.1.1.1

IPv4 subnet mask: 255.255.255.0

Description: VLAN 0003

Name: VLAN 0003

Tagged ports: None

Untagged ports: None

Table 2 Command output

Field	Description
VLAN type	VLAN type, static or dynamic.
Route interface	Whether the VLAN interface is configured for the VLAN. · Not configured. · Configured.
Description	Description of the VLAN.
Name	VLAN name.
IP address	Primary IPv4 address of the VLAN interface. This field is displayed only when an IPv4 address is configured for the VLAN interface. When the VLAN interface is also configured with secondary IPv4 addresses, you can view them by using one of the following commands: · display interface vlan-interface. · display this (VLAN interface view).
Subnet mask	Subnet mask of the primary IP address. This field is available only when an IP address is configured for the VLAN interface.
Tagged ports	Tagged members of the VLAN.
Untagged ports	Untagged members of the VLAN.

‌

Related commands

vlan

display vlan brief

Use display vlan brief to display brief VLAN information.

Syntax

display vlan brief

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display brief VLAN information.

<Sysname> display vlan brief

Brief information about all VLANs:

Supported Minimum VLAN ID: 1

Supported Maximum VLAN ID: 4094

Default VLAN ID: 1

VLAN ID Name Port

1 VLAN 0001 GE1/0/1 GE1/0/2 GE1/0/3 GE1/0/4

GE1/0/5 GE1/0/6 GE1/0/7 GE1/0/8

GE1/0/9 GE1/0/10 GE1/0/11

GE1/0/12 GE1/0/13 GE1/0/14

GE1/0/15 GE1/0/16 GE1/0/17

GE1/0/18 GE1/0/19 GE1/0/20

GE1/0/21 GE1/0/22 GE1/0/23

GE1/0/24 GE1/0/25 GE1/0/26

GE1/0/27 GE1/0/28 GE1/0/29

GE1/0/30 GE1/0/31 GE1/0/32

GE1/0/33 GE1/0/34 GE1/0/35

GE1/0/36 GE1/0/37 GE1/0/38

GE1/0/39 GE1/0/40 GE1/0/41

GE1/0/42 GE1/0/43 GE1/0/44

GE1/0/45 GE1/0/46 GE1/0/47

GE1/0/48

2 VLAN 0002

3 VLAN 0003

Table 3 Command output

Field	Description
Default VLAN ID	System default VLAN ID.
Name	VLAN name.
Port	Ports that allow packets from the VLAN to pass through.

‌

interface vlan-interface

Use interface vlan-interface to create a VLAN interface and enter its view, or enter the view of an existing VLAN interface.

Use undo interface vlan-interface to delete a VLAN interface.

Syntax

interface vlan-interface interface-number

undo interface vlan-interface interface-number

Default

No VLAN interfaces exist.

Views

System view

Predefined user roles

network-admin

Parameters

interface-number: Specifies a VLAN interface number in the range of 1 to 4094.

Usage guidelines

Create the VLAN before you create the VLAN interface for a VLAN.

Examples

# Create VLAN-interface 2, and enter its view.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2] quit

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2]

Related commands

display interface vlan-interface

mac-address

Use mac-address to assign a MAC address to a VLAN interface.

Use undo mac-address to restore the default.

Syntax

mac-address mac-address

undo mac-address

Default

The default MAC address of a VLAN interface varies by device model. The MAC address is the same for VLAN interfaces created on the device.

Views

VLAN interface view

Predefined user roles

network-admin

Parameters

mac-address: Specifies a MAC address in the format of H-H-H.

Examples

# Assign MAC address 0001-0001-0001 to VLAN-interface 2.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] mac-address 1-1-1

mtu

Use mtu to set the MTU for a VLAN interface.

Use undo mtu to restore the default.

Syntax

mtu size

undo mtu

Default

The MTU of a VLAN interface is 1500 bytes.

Views

VLAN interface view

Predefined user roles

network-admin

Parameters

size: Sets the MTU in the range of 46 to 1500 bytes.

Usage guidelines

If you configure both the mtu and ip mtu commands on a VLAN interface, the MTU set by the ip mtu command is used for fragmentation. For more information about the ip mtu command, see Layer 3—IP Services Command Reference.

Examples

# Set the MTU to 1492 bytes for VLAN-interface 1.

<Sysname> system-view

[Sysname] interface vlan-interface 1

[Sysname-Vlan-interface1] mtu 1492

Related commands

display interface vlan-interface

name

Use name to assign a name to a VLAN.

Use undo name to restore the default.

Syntax

name text

undo name

Default

The name of a VLAN is VLAN vlan-id. The vlan-id argument specifies the VLAN ID in a four-digit format. If the VLAN ID has fewer than four digits, leading zeros are added. For example, the name of VLAN 100 is VLAN 0100.

Views

VLAN view

Predefined user roles

network-admin

Parameters

text: Specifies a VLAN name, a case-sensitive string of 1 to 32 characters.

Usage guidelines

For 802.1X or MAC authentication, you can specify authorization VLANs by their names or IDs. If a large number of VLANs are configured, use VLAN names to identify them.

Examples

# Assign the name test vlan to VLAN 2.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2] name test vlan

Related commands

display vlan

reset counters interface vlan-interface

Use reset counters interface vlan-interface to clear statistics on a VLAN interface.

Syntax

reset counters interface [ vlan-interface [ interface-number ] ]

Views

User view

Predefined user roles

network-admin

Parameters

vlan-interface interface-number: Specifies a VLAN interface by its number. If you do not specify this option, this command clears statistics on all interfaces except VA interfaces. If you specify the vlan-interface keyword without specifying an interface, this command clears statistics on all VLAN interfaces.

Usage guidelines

Use this command to clear the history statistics before you collect statistics within a time period.

Examples

# Clear statistics on VLAN-interface 2.

<Sysname> reset counters interface vlan-interface 2

Related commands

display interface vlan-interface

service

Use service to specify a primary traffic processing slot for a VLAN interface.

Use undo service to restore the default.

Syntax

service slot slot-number

undo service slot

Default

No primary traffic processing slot is specified for a VLAN interface.

Views

VLAN interface view

Predefined user roles

network-admin

Parameters

slot slot-number: Specifies an IRF member device by its member ID.

Usage guidelines

The following matrix shows the support of hardware platform for this command:

Hardware	Command compatibility
MSR 810, MSR 810-W, MSR 810-W-DB, MSR 810-LM, MSR 810-W-LM, MSR 810-10-PoE, MSR 810-LM-HK, MSR 810-W-LM-HK	No
MSR 810-LMS, MSR 810-LUS	No
MSR 2600-6-X1, MSR 2600-10-X1	No
MSR 2630	Yes
MSR 3600-28, MSR 3600-51	Yes
MSR 3600-28-SI, MSR 3600-51-SI	No
MSR 3600-28-X1, MSR 3600-28-X1-DP, MSR 3600-51-X1, MSR 3600-51-X1-DP	Yes
MSR 3610-I-DP, MSR 3610-IE-DP	No
MSR 3610-X1, MSR 3610-X1-DP, MSR 3610-X1-DC, MSR 3610-X1-DP-DC	Yes
MSR 3610, MSR 3620, MSR 3620-DP, MSR 3640, MSR 3660	Yes
MSR 3610-G, MSR 3620-G	No

‌

This command is supported only in IRF mode.

Specify a traffic processing slot for a VLAN interface if all traffic on the VLAN interface must be processed on the same slot.

For high availability, you can specify one primary and one backup traffic processing slot by using the service command and the service standby command, respectively.

To avoid processing slot switchover, specify the primary slot before specifying the backup slot. If you specify the backup slot before specifying the primary slot, traffic is switched over to the primary slot immediately after you specify the primary slot.

If you specify both primary and backup slots for an interface, traffic on that interface is processed as follows:

· The backup slot takes over when the primary slot becomes unavailable. The backup slot continues to process traffic for the interface after the primary slot becomes available again. The switchover will not occur until the backup slot becomes unavailable.

· When no specified traffic processing slots are available, the traffic is processed on the slot at which it arrives. Then, the processing slot that first becomes available again takes over.

If you do not specify a primary or a backup traffic processing slot for an interface, traffic on that interface is processed on the slot at which the traffic arrives.

Examples

# Specify a primary traffic processing slot for VLAN-interface 2.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2] quit

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] service slot 2

Related commands

service standby

Use service standby to specify a backup traffic processing slot for an interface.

Use undo service standby to restore the default.

Syntax

service standby slot slot-number

undo service standby slot

Default

No backup traffic processing slot is specified for an interface.

Views

VLAN interface view

Predefined user roles

network-admin

Parameters

slot slot-number: Specifies an IRF member device by its member ID.

Usage guidelines

The following matrix shows the support of hardware platform for this command:

Hardware	Command compatibility
MSR 810, MSR 810-W, MSR 810-W-DB, MSR 810-LM, MSR 810-W-LM, MSR 810-10-PoE, MSR 810-LM-HK, MSR 810-W-LM-HK	No
MSR 810-LMS, MSR 810-LUS	No
MSR 2600-6-X1, MSR 2600-10-X1	No
MSR 2630	Yes
MSR 3600-28, MSR 3600-51	Yes
MSR 3600-28-SI, MSR 3600-51-SI	No
MSR 3600-28-X1, MSR 3600-28-X1-DP, MSR 3600-51-X1, MSR 3600-51-X1-DP	Yes
MSR 3610-I-DP, MSR 3610-IE-DP	No
MSR 3610-X1, MSR 3610-X1-DP, MSR 3610-X1-DC, MSR 3610-X1-DP-DC	Yes
MSR 3610, MSR 3620, MSR 3620-DP, MSR 3640, MSR 3660	Yes
MSR 3610-G, MSR 3620-G	No

‌

This command is supported only in IRF mode.

Specify a traffic processing slot for a VLAN interface if all traffic on the VLAN interface must be processed on the same slot.

For high availability, you can specify one primary and one backup traffic processing slot by using the service command and the service standby command, respectively.

If you specify both primary and backup slots for an interface, traffic on that interface is processed as follows:

· When no specified traffic processing slots are available, the traffic is processed on the slot at which it arrives. Then, the processing slot that first becomes available again takes over.

If you do not specify a primary or a backup traffic processing slot for an interface, traffic on that interface is processed on the slot at which the traffic arrives.

Examples

# Specify a primary and a backup traffic processing slot for VLAN-interface 2.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2] quit

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] service slot 2

[Sysname-Vlan-interface2] service standby slot 3

Related commands

service

shutdown

Use shutdown to shut down a VLAN interface.

Use undo shutdown to bring up a VLAN interface.

Syntax

shutdown

undo shutdown

Default

A VLAN interface is not manually shut down.

Views

VLAN interface view

Predefined user roles

network-admin

Usage guidelines

When a VLAN interface is not manually shut down, the following guidelines apply to the interface state:

· The VLAN interface is down if all ports in the VLAN are down.

· The VLAN interface is up if one or more ports in the VLAN are up.

When you use this command to shut down a VLAN interface, the VLAN interface remains in DOWN (Administratively) state. In this case, the VLAN interface state is not affected by the state of the ports in the VLAN.

Before you configure parameters for a VLAN interface, use this command to shut it down to prevent the configuration from affecting the network. After you complete the VLAN interface configuration, use the undo shutdown command to make the settings take effect.

To troubleshoot a failed VLAN interface, you can use the shutdown command and then the undo shutdown command on the interface to see whether it recovers.

In a VLAN, the state of each Ethernet port is independent of the state of the VLAN interface.

Examples

# Shut down VLAN-interface 2, and then bring it up.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] shutdown

[Sysname-Vlan-interface2] undo shutdown

vlan

Use vlan vlan-id to create a VLAN and enter its view, or enter the view of an existing VLAN.

Use vlan vlan-id1 to vlan-id2 to create VLANs vlan-id1 through vlan-id2, except reserved VLANs.

Use vlan all to create VLANs 1 through 4094.

Use undo vlan to delete the specified VLANs.

Syntax

vlan { vlan-id1 [ to vlan-id2 ] | all }

undo vlan { vlan-id1 [ to vlan-id2 ] | all }

Default

VLAN 1 (system default VLAN) exists.

Views

System view

Predefined user roles

network-admin

Parameters

vlan-id1: Specifies a VLAN ID in the range of 1 to 4094.

vlan-id1 to vlan-id2: Specifies a VLAN range. The vlan-id1 and vlan-id2 arguments specify VLAN IDs. The value range for each of the two arguments is 1 to 4094. The value for the vlan-id2 argument must be equal to or greater than the value for the vlan-id1 argument.

all: Specifies all VLANs except reserved VLANs. The keyword is not supported when the maximum number of VLANs that can be created on a device is less than 4094.

Usage guidelines

You cannot create or delete the system default VLAN (VLAN 1) or reserved VLANs.

Before you delete a dynamic VLAN or a VLAN locked by an application, you must first remove the configuration from the VLAN.

Examples

# Create VLAN 2 and enter its view.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2]

# Create VLANs 4 through 100.

<Sysname> system-view

[Sysname] vlan 4 to 100

Related commands

display vlan

Port-based VLAN commands

display port

Use display port to display information about hybrid or trunk ports.

Syntax

display port { hybrid | trunk }

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

hybrid: Specifies hybrid ports.

trunk: Specifies trunk ports.

Examples

# Display information about hybrid ports.

<Sysname> display port hybrid

Interface PVID VLAN Passing

GE1/0/1 100 Tagged: 1000, 1002, 1500, 1600-1611, 2000,

2555-2558, 3000, 4000

Untagged:1, 10, 15, 18, 20-30, 44, 55, 67, 100,

150-160, 200, 255, 286, 300-302

# Display information about trunk ports.

<Sysname> display port trunk

Interface PVID VLAN Passing

GE1/0/2 2 1-4, 6-100, 145, 177, 189-200, 244, 289, 400,

555, 600-611, 1000, 2006-2008

Table 4 Command output

Field	Description
Interface	Interface name.
PVID	Port VLAN ID.
VLAN Passing	Existing VLANs allowed on the port.
Tagged	VLANs from which the port sends packets without removing VLAN tags.
Untagged	VLANs from which the port sends packets after removing VLAN tags.

‌

port

Use port to assign the specified access ports to a VLAN.

Use undo port to remove the specified access ports from a VLAN.

Syntax

port interface-list

undo port interface-list

Default

All ports are in VLAN 1.

Views

VLAN view

Predefined user roles

network-admin

Parameters

interface-list: Specifies a space-separated list of up to 10 Ethernet interface items. Each item specifies an Ethernet interface or a range of Ethernet interfaces in the form of interface-type interface-number1 to interface-type interface-number2. The value for the interface-number2 argument must be equal to or greater than the value for the interface-number1 argument.

Usage guidelines

This command is applicable only to access ports.

By default, all ports are access ports. You can manually configure the port link type. For more information, see "port link-type."

Examples

# Assign GigabitEthernet 1/0/1 through GigabitEthernet 1/0/2 to VLAN 2.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2] port gigabitethernet 1/0/1 to gigabitethernet 1/0/2

Related commands

display vlan

port access vlan

Use port access vlan to assign an access port to the specified VLAN.

Use undo port access vlan to restore the default.

Syntax

port access vlan vlan-id

undo port access vlan

Default

All access ports belong to VLAN 1.

Views

Layer 2 aggregate interface view

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Parameters

vlan-id: Specifies a VLAN by its ID in the range of 1 to 4094.

Usage guidelines

Before assigning an access port to a VLAN, make sure the VLAN has been created.

Examples

# Assign GigabitEthernet 1/0/1 to VLAN 3.

<Sysname> system-view

[Sysname] vlan 3

[Sysname-vlan3] quit

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port access vlan 3

port hybrid pvid

Use port hybrid pvid to set the PVID of a hybrid port.

Use undo port hybrid pvid to set the PVID of a hybrid port to 1.

Syntax

port hybrid pvid vlan vlan-id

undo port hybrid pvid

Default

The PVID of a hybrid port is the ID of the VLAN to which the port belongs when its link type is access.

Views

Layer 2 aggregate interface view

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Parameters

vlan-id: Specifies a VLAN by its ID in the range of 1 to 4094.

Usage guidelines

You can use a nonexistent VLAN as the PVID of a hybrid port. When you delete the PVID of a hybrid port by using the undo vlan command, the PVID setting of the port does not change.

For correct packet transmission, set the same PVID for a local hybrid port and its peer.

To enable a hybrid port to transmit packets from its PVID, you must assign the hybrid port to the PVID by using the port hybrid vlan command.

Examples

# Configure GigabitEthernet 1/0/1 as a hybrid port, set its PVID to VLAN 100, and assign it to VLAN 100 as an untagged member.

<Sysname> system-view

[Sysname] vlan 100

[Sysname-vlan100] quit

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port link-type hybrid

[Sysname-GigabitEthernet1/0/1] port hybrid pvid vlan 100

[Sysname-GigabitEthernet1/0/1] port hybrid vlan 100 untagged

Related commands

port hybrid vlan

port link-type

port hybrid vlan

Use port hybrid vlan to assign a hybrid port to the specified VLANs.

Use undo port hybrid vlan to remove a hybrid port from the specified VLANs.

Syntax

port hybrid vlan vlan-id-list { tagged | untagged }

undo port hybrid vlan vlan-id-list

Default

A hybrid port is an untagged member of the VLAN to which the port belongs when its link type is access.

Views

Layer 2 aggregate interface view

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Parameters

vlan-id-list: Specifies a space-separated list of up to 10 VLAN items. Each item specifies a VLAN ID or a range of VLAN IDs in the form of vlan-id1 to vlan-id2. The value range for VLAN IDs is 1 to 4094. The value for the vlan-id2 argument must be equal to or greater than the value for the vlan-id1 argument. The specified VLANs must already exist on the device.

tagged: Configures the port as a tagged member of the specified VLANs. A tagged member of a VLAN sends packets from the VLAN without removing VLAN tags.

untagged: Configures the port as an untagged member of the specified VLANs. An untagged member of a VLAN sends packets from the VLAN after removing VLAN tags.

Usage guidelines

A hybrid port can allow multiple VLANs. If you execute this command multiple times on a hybrid port, the hybrid port allows all the specified VLANs.

Examples

# Configure GigabitEthernet 1/0/1 as a hybrid port, and assign it to VLAN 2, VLAN 4, and VLAN 50 through VLAN 100 as a tagged member.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port link-type hybrid

[Sysname-GigabitEthernet1/0/1] port hybrid vlan 2 4 50 to 100 tagged

Related commands

port link-type

Use port link-type to set the link type of a port.

Use undo port link-type to restore the default link type of a port.

Syntax

port link-type { access | hybrid | trunk }

undo port link-type

Default

Each port is an access port.

Views

Layer 2 aggregate interface view

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Parameters

access: Sets the port link type to access.

hybrid: Sets the port link type to hybrid.

trunk: Sets the port link type to trunk.

Usage guidelines

To change the link type of a port from trunk to hybrid or vice versa, first set the link type to access.

Examples

# Configure GigabitEthernet 1/0/1 as a trunk port.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port link-type trunk

port trunk permit vlan

Use port trunk permit vlan to assign a trunk port to the specified VLANs.

Use undo port trunk permit vlan to remove a trunk port from the specified VLANs.

Syntax

port trunk permit vlan { vlan-id-list | all }

undo port trunk permit vlan { vlan-id-list | all }

Default

A trunk port allows packets only from VLAN 1 to pass through.

Views

Layer 2 aggregate interface view

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Parameters

all: Specifies all VLANs. To prevent unauthorized VLAN users from accessing restricted resources through the port, use the port trunk permit vlan all command with caution.

Usage guidelines

A trunk port can allow multiple VLANs. If you execute this command multiple times on a trunk port, the trunk port allows all the specified VLANs.

On a trunk port, packets only from the PVID can pass through untagged.

Examples

# Configure GigabitEthernet 1/0/1 as a trunk port, and assign it to VLAN 2, VLAN 4, and VLAN 50 through VLAN 100.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port link-type trunk

[Sysname-GigabitEthernet1/0/1] port trunk permit vlan 2 4 50 to 100

Related commands

port link-type

port trunk pvid

Use port trunk pvid to set the PVID for a trunk port.

Use undo port trunk pvid to restore the default.

Syntax

port trunk pvid vlan vlan-id

undo port trunk pvid

Default

The PVID of a trunk port is VLAN 1.

Views

Layer 2 aggregate interface view

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Parameters

vlan-id: Specifies a VLAN by its ID in the range of 1 to 4094.

Usage guidelines

You can use a nonexistent VLAN as the PVID for a trunk port. When you delete the PVID of a trunk port by using the undo vlan command, the PVID setting of the port does not change.

For correct packet transmission, set the same PVID for a local trunk port and its peer.

To enable a trunk port to transmit packets from its PVID, you must assign the trunk port to the PVID by using the port trunk permit vlan command.

Examples

# Configure GigabitEthernet 1/0/1 as a trunk, set its PVID to VLAN 100, and assign it to VLAN 100.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port link-type trunk

[Sysname-GigabitEthernet1/0/1] port trunk pvid vlan 100

[Sysname-GigabitEthernet1/0/1] port trunk permit vlan 100

Related commands

port link-type

port trunk permit vlan

MAC-based VLAN commands

The following compatibility matrix shows the support of hardware platforms for this feature:

Hardware	Command compatibility
MSR810, MSR810-W, MSR810-W-DB, MSR810-LM, MSR810-W-LM, MSR810-10-PoE, MSR810-LM-HK, MSR810-W-LM-HK, MSR810-LMS-EA	No
MSR810-LMS, MSR810-LUS	No
MSR2600-6-X1, MSR2600-10-X1	No
MSR 2630	No
MSR3600-28, MSR3600-51	No
MSR3600-28-SI, MSR3600-51-SI	No
MSR3600-28-X1, MSR3600-28-X1-DP, MSR3600-51-X1, MSR3600-51-X1-DP	Yes
MSR3610-I-DP, MSR3610-IE-DP	No
MSR3610-X1, MSR3610-X1-DP, MSR3610-X1-DC, MSR3610-X1-DP-DC	No
MSR 3610, MSR 3620, MSR 3620-DP, MSR 3640, MSR 3660	No
MSR3610-G, MSR3620-G	No

‌

display mac-vlan

Use display mac-vlan to display MAC-to-VLAN entries.

Syntax

display mac-vlan { all | dynamic | mac-address mac-address [ mask mac-mask ] | static | vlan vlan-id }

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

all: Specifies all MAC-to-VLAN entries.

dynamic: Specifies dynamically configured MAC-to-VLAN entries.

mac-address mac-address: Specifies the MAC address in the MAC-to-VLAN entry. The format of the mac-address argument is H-H-H.

mask mac-mask: Specifies the mask for matching MAC addresses in MAC-to-VLAN entries. For the mac-mask argument, the high-order bits must be consecutive 1s in binary notation or consecutive Fs in hexadecimal notation. The default value is ffff-ffff-ffff.

static: Specifies statically configured MAC-to-VLAN entries.

vlan vlan-id: Specifies the VLAN in MAC-to-VLAN entries. The value range for the vlan-id argument is 1 to 4094.

Examples

# Display all MAC-to-VLAN entries.

<Sysname> display mac-vlan all

The following MAC VLAN entries exist:

State: S - Static, D - Dynamic

MAC address Mask VLAN ID Dot1q State

0008-0001-0000 ffff-ff00-0000 5 3 S

0002-0001-0000 ffff-ffff-ffff 5 3 S&D

Total MAC VLAN entries count: 2

Table 5 Command output

Field	Description
S - Static	Statically configured MAC-to-VLAN entries.
D - Dynamic	Dynamically configured MAC-to-VLAN entries.
MAC address	MAC address of the MAC-to-VLAN entry.
Mask	MAC address mask of the MAC-to-VLAN entry.
VLAN ID	VLAN ID of the MAC-to-VLAN entry.
Dot1q	802.1p priority of the VLAN in the MAC-to-VLAN entry.
State	State of a MAC-to-VLAN entry: · S—The MAC-to-VLAN entry is configured statically. · D—The MAC-to-VLAN entry is dynamically issued by the authentication server. · S&D—The MAC-to-VLAN entry is configured both statically and dynamically.

‌

Related commands

mac-vlan mac-address

display mac-vlan interface

Use display mac-vlan interface to display all ports that are enabled with the MAC-based VLAN feature.

Syntax

display mac-vlan interface

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display all ports that are enabled with the MAC-based VLAN feature.

<Sysname> display mac-vlan interface

MAC VLAN is enabled on following ports:

GigabitEthernet1/0/1 GigabitEthernet1/0/2 GigabitEthernet1/0/3

Related commands

mac-vlan enable

Use mac-vlan enable to enable the MAC-based VLAN feature on a port.

Use undo mac-vlan enable to disable the MAC-based VLAN feature on a port.

Syntax

mac-vlan enable

undo mac-vlan enable

Default

The MAC-based VLAN feature is disabled on a port.

Views

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Examples

# Enable the MAC-based VLAN feature on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname–GigabitEthernet1/0/1] mac-vlan enable

Related commands

display mac-vlan interface

mac-vlan mac-address

Use mac-vlan mac-address to configure a MAC-to-VLAN entry.

Use undo mac-vlan to delete the specified MAC-to-VLAN entries.

Syntax

mac-vlan mac-address mac-address [ mask mac-mask ] vlan vlan-id [ dot1q priority ]

undo mac-vlan { all | mac-address mac-address [ mask mac-mask ] | vlan vlan-id }

Default

No MAC-to-VLAN entries exist.

Views

System view

Predefined user roles

network-admin

Parameters

mac-address mac-address: Specifies a MAC address in the format of H-H-H. The MAC address cannot be a multicast MAC address or all 0s. When you configure a MAC address, leading zeros in each H section can be omitted. For example, to configure a MAC address 000f-00e2-0001, you can enter only f-e2-1.

mask mac-mask: Specifies the MAC address mask. For the mac-mask argument, the high-order bits must be consecutive 1s in binary notation or consecutive Fs in hexadecimal notation. The default value is ffff-ffff-ffff.

vlan vlan-id: Specifies a VLAN ID in the range of 1 to 4094.

dot1q priority: Specifies the 802.1p priority of the VLAN specific to the MAC-to-VLAN entry. The value range for the priority argument is 0 to 7, and the default value is 0. The higher the value, the higher the 802.1p priority.

all: Specifies all static MAC-to-VLAN entries.

Usage guidelines

For successful dynamic MAC-based VLAN assignment, use static VLANs when you create MAC-to-VLAN entries.

Different types of MAC-to-VLAN entries are created depending on whether you specify the mask keyword.

· When you specify this keyword, the created MAC-to-VLAN entry describes the relationship among a group of MAC addresses, a VLAN, and the 802.1p priority for the VLAN.

· When you do not specify this keyword, the created MAC-to-VLAN entry describes the relationship among a MAC address, a VLAN, and the 802.1p priority for the VLAN.

These different types of MAC-to-VLAN entries are stored separately in two tables. The system updates the two tables according to the configuration.

Examples

# Associate the MAC address 0000-0001-0001 with VLAN 100, and set the 802.1p priority to 7 for VLAN 100 in this entry.

<Sysname> system-view

[Sysname] mac-vlan mac-address 0-1-1 vlan 100 dot1q 7

# Associate VLAN 100 with MAC addresses whose six high-order bits are 121122, and set the 802.1p priority to 4 for VLAN 100 in this entry.

<Sysname> system-view

[Sysname] mac-vlan mac-address 1211-2222-3333 mask ffff-ff00-0000 vlan 100 dot1q 4

Related commands

display mac-vlan

mac-vlan trigger enable

Use mac-vlan trigger enable to enable dynamic MAC-based VLAN assignment on a port.

Use undo mac-vlan trigger enable to disable dynamic MAC-based VLAN assignment on a port.

Syntax

mac-vlan trigger enable

undo mac-vlan trigger enable

Default

Dynamic MAC-based VLAN assignment is disabled on a port.

Views

Layer 2 aggregate interface view

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

VLAN assignment for a port is triggered only when the source MAC address of its received packet exactly matches the MAC address in a MAC-to-VLAN entry.

Examples

# Enable dynamic MAC-based VLAN assignment on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] mac-vlan trigger enable

Related commands

mac-vlan mac-address

port pvid forbidden

Use port pvid forbidden to disable a port from forwarding packets that fail the exact MAC address match in its PVID.

Use undo port pvid forbidden to restore the default.

Syntax

port pvid forbidden

undo port pvid forbidden

Default

When a port receives packets whose source MAC addresses fail the exact MAC address match, the port forwards them in its PVID.

Views

Layer 2 aggregate interface view

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

Use this feature only with dynamic MAC-based VLAN assignment.

Examples

# Disable GigabitEthernet 1/0/1 from forwarding packets that fail the exact MAC address match in its PVID.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port pvid forbidden

Related commands

mac-vlan trigger enable

VLAN group commands

display vlan-group

Use display vlan-group to display VLAN group information.

Syntax

display vlan-group [ group-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

group-name: Specifies a VLAN group by its name, a case-sensitive string of 1 to 31 characters. The first character must be an alphabetical character. If you do not specify this argument, the command displays information about all VLAN groups.

Examples

# Display information about VLAN group test001.

<Sysname> display vlan-group test001

VLAN group: test001

VLAN list: 2-4 100 200

# Display information about all VLAN groups.

<Sysname> display vlan-group

VLAN group: rnd

VLAN list: Null

VLAN group: test001

VLAN list: 2-4 100 200

Table 6 Command output

Field	Description
VLAN group	Name of the VLAN group.
VLAN list	VLAN list in the VLAN group.

‌

Related commands

vlan-group

vlan-list

vlan-group

Use vlan-group to create a VLAN group and enter its view, or enter the view of an existing VLAN group.

Use undo vlan-group to delete a VLAN group.

Syntax

vlan-group group-name

undo vlan-group group-name

Default

No VLAN groups exist.

Views

System view

Predefined user roles

network-admin

Parameters

group-name: Specifies a VLAN group by its name, a case-sensitive string of 1 to 31 characters. The first character must be an alphabetical character.

Usage guidelines

A VLAN group includes a set of VLANs. You can add multiple VLAN lists to a VLAN group.

On an authentication server, a VLAN group name represents a group of authorization VLANs. When an 802.1X user passes authentication, the authentication server assigns a VLAN group name to the device. The device then uses the received VLAN group name to match the locally configured VLAN group names. If a match is found, the device selects a VLAN from the group and assigns the VLAN to the user.

Examples

# Create a VLAN group named test001 and enter VLAN group view.

<Sysname> system-view

[Sysname] vlan-group test001

[Sysname-vlan-group-test001]

Related commands

vlan-list

Use vlan-list to add VLANs to a VLAN group.

Use undo vlan-list to remove VLANs from a VLAN group.

Syntax

vlan-list vlan-id-list

undo vlan-list vlan-id-list

Default

No VLANs exist in a VLAN group.

Views

VLAN group view

Predefined user roles

network-admin

Parameters

Examples

# Add VLAN 2 through VLAN 4, VLAN 100, and VLAN 200 to VLAN group test001.

<Sysname> system-view

[Sysname] vlan-group test001

[Sysname-vlan-group-test001] vlan-list 2 to 4 100 200

Related commands

vlan-group

Super VLAN commands

This feature is supported only on the following ports:

· Layer 2 Ethernet ports on Ethernet switching modules.

· Fixed Layer 2 Ethernet ports of the following routers:

¡ MSR810, MSR810-W, MSR810-W-DB, MSR810-LM, MSR810-W-LM, MSR810-10-PoE, MSR810-LM-HK, MSR810-W-LM-HK, MSR810-LMS-EA.

¡ MSR2600-6-X1, MSR2600-10-X1.

¡ MSR3600-28, MSR3600-28-X1, MSR3600-51, MSR3600-51-X1, MSR3600-28-SI, MSR3600-51-SI.

¡ MSR3610-I-DP, MSR3610-IE-DP.

display supervlan

Use display supervlan to display information about super VLANs and their associated sub-VLANs.

Syntax

display supervlan [ supervlan-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

supervlan-id: Specifies a super VLAN ID in the range of 1 to 4094. If you do not specify a super VLAN ID, this command displays information about all super VLANs and their associated sub-VLANs.

Examples

# Display information about super VLAN 2 and its associated sub-VLANs.

<Sysname> display supervlan 2

Super VLAN ID: 2

Sub-VLAN ID: 3-5

VLAN ID: 2

VLAN type: Static

It is a super VLAN.

Route interface: Configured

IPv4 address: 10.153.17.41

IPv4 subnet mask: 255.255.252.0

IPv6 global unicast addresses:

2001::1, subnet is 2001::/64 [TENTATIVE]

Description: VLAN 0002

Name: VLAN 0002

Tagged ports: None

Untagged ports: None

VLAN ID: 3

VLAN type: Static

It is a sub VLAN.

Route interface: Configured

IPv4 address: 10.153.17.41

IPv4 subnet mask: 255.255.252.0

IPv6 global unicast addresses:

2001::1, subnet is 2001::/64 [TENTATIVE]

Description: VLAN 0003

Name: VLAN 0003

Tagged ports: None

Untagged ports:

GigabitEthernet1/0/3

VLAN ID: 4

VLAN type: Static

It is a sub VLAN.

Route interface: Configured

IPv4 address: 10.153.17.41

IPv4 subnet mask: 255.255.252.0

IPv6 global unicast addresses:

2001::1, subnet is 2001::/64 [TENTATIVE]

Description: VLAN 0004

Name: VLAN 0004

Tagged ports: None

Untagged ports:

GigabitEthernet1/0/4

Table 7 Command output

Field	Description
VLAN type	VLAN type, dynamic or static.
Route interface	Whether a VLAN interface is configured for the VLAN.
IPv4 address	Primary IPv4 address of the VLAN interface. This field is displayed only when an IPv4 address is configured for the VLAN interface. When the VLAN interface is also configured with secondary IPv4 addresses, you can view them by using one of the following commands: · display interface vlan-interface. · display this (VLAN interface view).
IPv4 subnet mask	Subnet mask for the primary IPv4 address of the VLAN interface. This field is displayed only when an IPv4 address is configured for the VLAN interface.
IPv6 global unicast addresses	Global unicast IPv6 address of the VLAN interface. This field is not displayed when no IPv6 address is configured for the VLAN interface. The IPv6 address states are as follows: · TENTATIVE—Initial state. DAD is being performed or is to be performed on the address. An address in this state cannot be used as the source address or destination address of packets. · DUPLICATE—DAD has been completed for the address. The address is not unique on the link and cannot be used. · PREFERRED—The address is preferred and can be used as the source or destination address of a packet. If an address is in this state, the command does not display the address state. · DEPRECATED—The address is beyond the preferred lifetime but within the valid lifetime. It is valid, but it cannot be used as the source address for a new connection. Packets destined to the address are processed correctly.
Description	VLAN description.
Name	VLAN name.
Tagged ports	Tagged members of the VLAN.
Untagged ports	Untagged members of the VLAN.

‌

Related commands

subvlan

supervlan

subvlan

Use subvlan to associate a super VLAN with the specified sub-VLANs.

Use undo subvlan to dissociate sub-VLANs from a super VLAN.

Syntax

subvlan vlan-id-list

undo subvlan [ vlan-id-list ]

Default

A super VLAN is not associated with any sub-VLANs.

Views

VLAN view

Predefined user roles

network-admin

Parameters

vlan-id-list: Specifies a space-separated list of up to 10 sub-VLAN items. Each item specifies a sub-VLAN ID or a range of sub-VLAN IDs in the form of vlan-id1 to vlan-id2. The value range for sub-VLAN IDs is 1 to 4094. The value for the vlan-id2 argument must be equal to or greater than the value for the vlan-id1 argument.

Usage guidelines

Make sure sub-VLANs already exist before you associate them with a super VLAN.

You can add ports to and remove ports from a sub-VLAN that is already associated with a super VLAN.

When you use the undo subvlan command, follow these guidelines:

· If you do not specify the vlan-id-list argument, this command dissociates all sub-VLANs from the current super VLAN.

· If you specify the vlan-id-list argument, this command dissociates the specified sub-VLANs from the current super VLAN.

Examples

# Associate super VLAN 10 with sub-VLANs 3, 4, and 5.

<Sysname> system-view

[Sysname] vlan 3 to 5

[Sysname] vlan 10

[Sysname-vlan10] supervlan

[Sysname-vlan10] subvlan 3 to 5

Related commands

display supervlan

supervlan

Use supervlan to configure a VLAN as a super VLAN.

Use undo supervlan to restore the default.

Syntax

supervlan

undo supervlan

Default

A VLAN is not a super VLAN.

Views

VLAN view

Predefined user roles

network-admin

Usage guidelines

A VLAN cannot be configured as both a super VLAN and a guest VLAN, Auth-Fail VLAN, or critical VLAN. For more information about guest VLANs, Auth-Fail VLANs, and critical VLANs, see Security Configuration Guide.

As a best practice, do not configure VRRP for a super VLAN interface, because the configuration affects network performance.

Layer 2 multicast configuration for super VLANs does not take effect because they do not have physical ports.

Examples

# Configure VLAN 2 as a super VLAN.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2] supervlan

Related commands

display supervlan

subvlan

Voice VLAN commands

This feature is supported only on the following ports:

· Layer 2 Ethernet ports on Ethernet switching modules.

¡ HMIM-8GSW.

¡ HMIM-8GSWF.

¡ HMIM-24GSW(P).

¡ SIC-4GSW(P).

· Fixed Layer 2 Ethernet ports of the following routers:

¡ MSR810, MSR810-W, MSR810-W-DB, MSR810-LM, MSR810-W-LM, MSR810-10-PoE, MSR810-LM-HK, MSR810-W-LM-HK, MSR810-LMS-EA.

¡ MSR2600-6-X1, MSR2600-10-X1.

¡ MSR3600-28, MSR3600-28-X1, MSR3600-51, MSR3600-51-X1, MSR3600-28-SI, MSR3600-51-SI.

¡ MSR3610-I-DP, MSR3610-IE-DP.

display voice-vlan mac-address

Use display voice-vlan mac-address to display the OUI addresses supported on the device.

Syntax

display voice-vlan mac-address

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display the OUI addresses supported on the device.

<Sysname> display voice-vlan mac-address

OUI Address Mask Description

0001-e300-0000 ffff-ff00-0000 Siemens phone

0003-6b00-0000 ffff-ff00-0000 Cisco phone

0004-0d00-0000 ffff-ff00-0000 Avaya phone

000f-e200-0000 ffff-ff00-0000 H3C Aolynk phone

0060-b900-0000 ffff-ff00-0000 Philips/NEC phone

00d0-1e00-0000 ffff-ff00-0000 Pingtel phone

00e0-7500-0000 ffff-ff00-0000 Polycom phone

00e0-bb00-0000 ffff-ff00-0000 3Com phone

Table 8 Command output

Field	Description
OUI Address	OUI address allowed on the device.
Mask	Mask of the OUI address.
Description	Description of the OUI address.

‌

Related commands

voice-vlan mac-address

display voice-vlan state

Use display voice-vlan state to display voice VLAN information.

Syntax

display voice-vlan state

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display voice VLAN information.

<Sysname> display voice-vlan state

Current voice VLANs: 1

Voice VLAN security mode: Security

Voice VLAN aging time: 1440 minutes

Voice VLAN enabled ports and their modes:

Port VLAN Mode CoS DSCP

GE1/0/1 111 Auto 6 46

Table 9 Command output

Field	Description
Current Voice VLANs	Number of existing voice VLANs.
Voice VLAN security mode	Voice VLAN mode: · Security. · Normal.
Voice VLAN aging time	Voice VLAN aging timer.
Voice VLAN enabled ports and their modes	Voice VLAN-enabled ports and their voice VLAN assignment modes.
Port	Name of the voice VLAN-enabled port.
VLAN	ID of the voice VLAN enabled on the port.
Mode	Voice VLAN assignment mode of the port: · Manual. · Automatic.

‌

Related commands

voice-vlan aging

voice-vlan enable

voice-vlan mode auto

voice-vlan security enable

voice-vlan aging

Use voice-vlan aging to set the voice VLAN aging timer.

Use undo voice-vlan aging to restore the default.

Syntax

voice-vlan aging minutes

undo voice-vlan aging

Default

The voice VLAN aging timer is 1440 minutes (24 hours).

Views

System view

Predefined user roles

network-admin

Parameters

minutes: Sets the voice VLAN aging timer in the range of 5 to 43200 in minutes.

Usage guidelines

In automatic voice VLAN assignment mode, the device starts an aging timer for a voice VLAN when assigning a port to the voice VLAN. If no voice packets are received on the port before the timer expires, the device removes the port from the voice VLAN.

The aging timer of a voice VLAN starts only when the dynamic MAC address entry of the voice VLAN ages out. The aging period for the voice VLAN equals the sum of the voice VLAN aging timer and the aging timer for its dynamic MAC address entry. For more information about the aging timer for dynamic MAC address entries, see MAC address table configuration in Layer 2—LAN Switching Configuration Guide.

Set the voice VLAN aging timer only when the voice VLAN assignment mode is automatic.

Examples

# Set the voice VLAN aging timer to 100 minutes.

<Sysname> system-view

[Sysname] voice-vlan aging 100

Related commands

display voice-vlan state

voice-vlan enable

Use voice-vlan enable to enable the voice VLAN feature on a port.

Use undo voice-vlan enable to disable the voice VLAN feature on a port.

Syntax

voice-vlan vlan-id enable

undo voice-vlan [ vlan-id ] enable

Default

The voice VLAN feature is disabled on ports.

Views

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Parameters

vlan-id: Specifies a voice VLAN ID in the range of 2 to 4094.

Usage guidelines

Use this command only on a hybrid or trunk port operating in automatic voice VLAN assignment mode.

Before you execute this command, make sure the specified VLAN already exists.

Examples

# Enable the voice VLAN feature on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] voice-vlan 2 enable

Related commands

display voice-vlan state

voice-vlan mode auto

voice-vlan mac-address

Use voice-vlan mac-address to configure the OUI address information for voice packet identification.

Use undo voice-vlan mac-address to delete an OUI address.

Syntax

voice-vlan mac-address mac-address mask oui-mask [ description text ]

undo voice-vlan mac-address oui

Default

System default OUI addresses exist.

Table 10 System default OUI addresses

Number	OUI address	Vendor
1	0001-e300-0000		Siemens phone
2	0003-6b00-0000		Cisco phone
3	0004-0d00-0000		Avaya phone
4	000f-e200-0000		H3C Aolynk phone
5	0060-b900-0000		Philips/NEC phone
6	00d0-1e00-0000		Pingtel phone
7	00e0-7500-0000		Polycom phone
8	00e0-bb00-0000		3Com phone

‌

Views

System view

Predefined user roles

network-admin

Parameters

mac-address: Specifies a source MAC address of voice traffic, in the format of H-H-H. For example, 1234-1234-1234.

mask oui-mask: Specifies the valid length of the OUI address by using a mask in the format of H-H-H. The mask contains consecutive 1s and 0s. For example, ffff-0000-0000. To match the voice devices of a vendor, set the mask to ffff-ff00-0000.

description text: Specifies the OUI address description, a case-sensitive string of 1 to 30 characters.

oui: Specifies an OUI address to delete, in the format of H-H-H. For example, 1234-1200-0000. An OUI address is the logical AND result of the mac-address and oui-mask arguments. It cannot be a broadcast address, a multicast address, or an all-zero address.

Usage guidelines

You can manually delete or add the system default OUI addresses.

The maximum number of configurable OUI addresses depends on the device model.

Examples

# Add OUI address 1234-1200-0000 by specifying the MAC address as 1234-1234-1234 and the mask as fff-ff00-0000. Configure the OUI address description as PhoneA.

<Sysname> system-view

[Sysname] voice-vlan mac-address 1234-1234-1234 mask ffff-ff00-0000 description PhoneA

Related commands

display voice-vlan mac-address

voice-vlan mode auto

Use voice-vlan mode auto to configure a port to operate in automatic voice VLAN assignment mode.

Use undo voice-vlan mode auto to configure a port to operate in manual voice VLAN assignment mode.

Syntax

voice-vlan mode auto

undo voice-vlan mode auto

Default

A port operates in automatic voice VLAN assignment mode.

Views

Layer 2 aggregate interface view

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

To make a voice VLAN take effect on a port operating in manual mode, you must manually assign the port to the voice VLAN.

Examples

# Configure GigabitEthernet 1/0/1 to operate in manual voice VLAN assignment mode.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] undo voice-vlan mode auto

Related commands

display voice-vlan state

voice-vlan security enable

Use voice-vlan security enable to enable the voice VLAN security mode.

Use undo voice-vlan security enable to disable the voice VLAN security mode.

Syntax

voice-vlan security enable

undo voice-vlan security enable

Default

The voice VLAN security mode is enabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

In security mode, a voice VLAN transmits only voice packets whose source MAC addresses match the OUI addresses of the device.

In normal mode, a voice VLAN transmits voice packets and non-voice packets.

Examples

# Disable the voice VLAN security mode.

<Sysname> system-view

[Sysname] undo voice-vlan security enable

Related commands

display voice-vlan state

voice-vlan track lldp

Use voice-vlan track lldp to enable LLDP for automatic IP phone discovery.

Use undo voice-vlan track lldp to disable LLDP for automatic IP phone discovery.

Syntax

voice-vlan track lldp

undo voice-vlan track lldp

Views

System view

Default

LLDP for automatic IP phone discovery is disabled.

Predefined user roles

network-admin

Examples

# Enable LLDP for automatic IP phone discovery.

<Sysname> system-view

[Sysname] voice-vlan track lldp

04-Layer 2—LAN Switching Command Reference

VLAN commands

display interface vlan-interface

interface vlan-interface

reset counters interface vlan-interface

port pvid forbidden

Super VLAN commands

display voice-vlan mac-address

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

News & Events

Contact Us