12-Network Management and Monitoring

HomeSupportReference GuidesCommand ReferencesH3C Access Controllers Command References(E5208P03 E5215P01 R5215P01)-6W10212-Network Management and Monitoring
13-Mirroring commands
Title Size Download
13-Mirroring commands 48.56 KB

Port mirroring commands

The following matrix shows the feature and hardware compatibility:

 

Hardware series

Model

Port mirroring compatibility

WX1800H series

WX1804H

WX1810H

WX1820H

Yes

WX2500H series

WX2510H

WX2540H

WX2560H

Yes

WX3000H series

WX3010H

WX3010H-L

WX3010H-X

WX3024H

WX3024H-L

Yes

WX3500H series

WX3508H

WX3510H

WX3520H

WX3540H

Yes

WX5500E series

WX5510E

WX5540E

Yes

WX5500H series

WX5540H

WX5560H

WX5580H

Yes

Access controller modules

EWPXM1MAC0F

EWPXM1WCME0

EWPXM2WCMD0F

LSQM1WCMX20

LSQM1WCMX40

LSUM1WCME0

LSUM1WCMX20RT

LSUM1WCMX40RT

No

 

display mirroring-group

Use display mirroring-group to display mirroring group information.

Syntax

display mirroring-group { group-id | all | local }

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

group-id: Specifies a mirroring group by its number in the range of 1 to 2.

all: Specifies all mirroring groups.

local: Specifies local mirroring groups.

Usage guidelines

Mirroring group information includes the type, status, and content of a mirroring group. It is sorted by mirroring group number.

Examples

# Display information about all mirroring groups.

<Sysname> display mirroring-group all

Mirroring group 1:

    Type: Local

    Status: Active

    Mirroring port:

        GigabitEthernet1/0/1  Inbound

    Monitor port: GigabitEthernet1/0/2

Table 1 Command output

Field

Description

Mirroring group

Number of the mirroring group.

Type

Type of the mirroring group.

The device supports only local mirroring groups.

Status

Status of the mirroring group:

·     Active—The mirroring group has taken effect.

·     Incomplete—The mirroring group configuration is not complete and does not take effect.

Mirroring port

Source port.

Monitor port

Destination port.

 

mirroring-group

Use mirroring-group to create a mirroring group.

Use undo mirroring-group to delete mirroring groups.

Syntax

mirroring-group group-id local

undo mirroring-group { group-id | all | local }

Default

No mirroring groups exist.

Views

System view

Predefined user roles

network-admin

Parameters

group-id: Specifies a mirroring group by its number in the range of 1 to 2.

local: Specifies local mirroring groups.

all: Specifies all mirroring groups.

Examples

# Create local mirroring group 1.

<Sysname> system-view

[Sysname] mirroring-group 1 local

mirroring-group mirroring-port (interface view)

Use mirroring-group mirroring-port to configure a port as a source port for a mirroring group.

Use undo mirroring-group mirroring-port to restore the default.

Syntax

mirroring-group group-id mirroring-port { both | inbound | outbound }

undo mirroring-group group-id mirroring-port

Default

A port does not act as a source port for any mirroring groups.

Views

Interface view

Predefined user roles

network-admin

Parameters

group-id: Specifies a mirroring group by its number in the range of 1 to 2. The specified mirroring group must already exist.

both: Mirrors both received and sent packets.

inbound: Mirrors only received packets.

outbound: Mirrors only sent packets.

Usage guidelines

A Layer 2 aggregate interface cannot be configured as a source port for a mirroring group.

A port can act as a source port for only one mirroring group.

A source port cannot be used as a monitor port.

Examples

# Create local mirroring group 1 to monitor the bidirectional traffic of GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] mirroring-group 1 local

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] mirroring-group 1 mirroring-port both

Related commands

mirroring-group

mirroring-group mirroring-port (system view)

Use mirroring-group mirroring-port to configure source ports for a mirroring group.

Use undo mirroring-group mirroring-port to remove source ports from a mirroring group.

Syntax

mirroring-group group-id mirroring-port interface-list { both | inbound | outbound }

undo mirroring-group group-id mirroring-port interface-list

Default

No source port is configured for a mirroring group.

Views

System view

Predefined user roles

network-admin

Parameters

group-id: Specifies a mirroring group by its number in the range of 1 to 2. The specified mirroring group must already exist.

interface-list: Specifies a space-separated list of up to eight port items. Each item specifies a single port or a port range in the form of interface-type interface-number1 to interface-type interface-number2. The specified interfaces must be of the same type and on the same card. The value for the interface-number2 argument must be equal to or greater than the value for the interface-number1 argument.

both: Mirrors both received and sent packets.

inbound: Mirrors only received packets.

outbound: Mirrors only sent packets.

Usage guidelines

A Layer 2 aggregate interface cannot be configured as a source port for a mirroring group.

A port can act as a source port for only one mirroring group.

A source port cannot be used as a monitor port.

Examples

# Create local mirroring group 1 to monitor the bidirectional traffic of GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] mirroring-group 1 local

[Sysname] mirroring-group 1 mirroring-port gigabitethernet 1/0/1 both

Related commands

mirroring-group

mirroring-group monitor-port (interface view)

Use mirroring-group monitor-port to configure a port as a monitor port for a mirroring group.

Use undo mirroring-group monitor-port to restore the default.

Syntax

mirroring-group group-id monitor-port

undo mirroring-group group-id monitor-port

Default

A port does not act as a monitor port for any mirroring groups.

Views

Interface view

Predefined user roles

network-admin

Parameters

group-id: Specifies a mirroring group by its number in the range of 1 to 2. The specified mirroring group must already exist.

Usage guidelines

Do not enable the spanning tree feature on the monitor port of a mirroring group.

For a Layer 2 aggregate interface configured as the monitor port of a mirroring group, do not configure its member ports as source ports of the mirroring group.

Use a monitor port only for port mirroring, so the data monitoring device receives and analyzes only the mirrored traffic.

Do not configure a port of an existing mirroring group as a monitor port.

Examples

# Create local mirroring group 1 and configure GigabitEthernet 1/0/1 as its monitor port.

<Sysname> system-view

[Sysname] mirroring-group 1 local

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] mirroring-group 1 monitor-port

Related commands

mirroring-group

mirroring-group monitor-port (system view)

Use mirroring-group monitor-port to configure the monitor ports for a mirroring group.

Use undo mirroring-group monitor-port to remove the monitor ports from a mirroring group.

Syntax

mirroring-group group-id monitor-port interface-list

undo mirroring-group group-id monitor-port interface-list

Default

No monitor port is configured for a mirroring group.

Views

System view

Predefined user roles

network-admin

Parameters

group-id: Specifies a mirroring group by its number in the range of 1 to 2. The specified mirroring group must already exist.

interface-list: Specifies a space-separated list of up to eight port items. Each item specifies a single port or a port range in the form of interface-type interface-number1 to interface-type interface-number2. The value for the interface-number2 argument must be equal to or greater than the value for the interface-number1 argument.

Usage guidelines

Do not enable the spanning tree feature on the monitor port of a mirroring group.

For a Layer 2 aggregate interface configured as the monitor port of a mirroring group, do not configure its member ports as source ports of the mirroring group.

Use a monitor port only for port mirroring, so the data monitoring device receives only the mirrored traffic.

Do not configure a port of an existing mirroring group as a monitor port.

Examples

# Create local mirroring group 1 and configure GigabitEthernet 1/0/1 as its monitor port.

<Sysname> system-view

[Sysname] mirroring-group 1 local

[Sysname] mirroring-group 1 monitor-port gigabitethernet 1/0/1

Related commands

mirroring-group

  • Cloud & AI
  • InterConnect
  • Intelligent Computing
  • Intelligent Storage
  • Security
  • SMB Products
  • Intelligent Terminal Products
  • Product Support Services
  • Technical Service Solutions
All Services
  • Resource Center
  • Policy
  • Online Help
  • Technical Blogs
All Support
  • Become A Partner
  • Partner Policy & Program
  • Global Learning
  • Partner Sales Resources
  • Partner Business Management
  • Service Business
All Partners
  • Profile
  • News & Events
  • Online Exhibition Center
  • Contact Us
All About Us
新华三官网