vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays information about interfaces maintained by the IPv6 MRIB on the public network.

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays information about all interfaces maintained by the IPv6 MRIB.

Examples

# Display information about all interfaces maintained by the IPv6 MRIB on the public network.

<Sysname> display ipv6 mrib interface

Interface: GigabitEthernet1/0/1

Index: 0x00000001

Current state: up

MTU: 1500

Type: BROADCAST

Protocol: PIM-DM

PIM protocol state: Enabled

Address list:

1. Local address : FE80:7:11::1/10

Remote address: ::

Reference : 1

State : NORMAL

Table 1 Command output

Field	Description
Interface	Interface name.
Index	Index number of the interface.
Current state	Current status of the interface: up or down.
MTU	MTU value.
Type	Interface type: · BROADCAST—Broadcast link interface. · P2P—P2P interface. · LOOP—Loopback interface. · REGISTER—Register interface. · NBMA—NBMA interface. · MTUNNEL—Multicast tunnel interface. This field is empty if the interface is Null 0.
Protocol	Protocol running on the interface: PIM-DM, PIM-SM, MLD, or PROXY.
PIM protocol state	Whether IPv6 PIM is enabled: Enabled or Disabled.
Address list	Interface address list.
Local address	Local IP address.
Remote address	Remote end IP address. This field is displayed only when the interface is vlink type.
Reference	Number of times that the address has been referenced.
State	Status of the interface address: NORMAL or DEL.

display ipv6 multicast boundary

Use display ipv6 multicast boundary to display IPv6 multicast boundary information.

Syntax

display ipv6 multicast [ vpn-instance vpn-instance-name ] boundary { group [ ipv6-group-address [ prefix-length ] ] | scope [ scope-id ] } [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays IPv6 multicast boundary information on the public network.

group: Displays the IPv6 multicast boundary information for the specified group.

ipv6-group-address: Specifies an IPv6 multicast group address in the range of FFxy::/16, where "x" and "y" represent any hexadecimal numbers from 0 to F. If you do not specify an IPv6 multicast group, this command displays IPv6 multicast boundary information of all IPv6 multicast groups.

prefix-length: Specifies an address prefix length in the range of 8 to 128. The default is 128.

scope: Displays IPv6 multicast group boundary information in the admin-scoped zone.

scope-id: Specifies an admin-scoped zone by its ID in the range of 3 to 15, which is identified by the scope field in the IPv6 multicast group address. If you do not specify an admin-scoped zone, this command displays IPv6 multicast boundary information of all IPv6 admin-scoped zones.

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays IPv6 multicast boundary information for all interfaces.

Examples

# Display IPv6 multicast boundary information of all IPv6 multicast groups on all interfaces on the public network.

<Sysname> display ipv6 multicast boundary group

Boundary Interface

FF1E::/64 GE1/0/1

# Display IPv6 multicast boundary information in all IPv6 admin-scoped zones on all interfaces on the public network.

<Sysname> display ipv6 multicast boundary scope

Boundary Interface

3 GigabitEthernet1/0/1

Table 2 Command output

Field	Description
Boundary	IPv6 multicast group or IPv6 admin-scoped zone that is associated with the IPv6 multicast boundary.
Interface	Boundary interface that is associated with the IPv6 multicast boundary.

Related commands

ipv6 multicast boundary

display ipv6 multicast forwarding df-info

Use display ipv6 multicast forwarding df-info to display DF information.

Syntax

In standalone mode:

display ipv6 multicast [ vpn-instance vpn-instance-name ] forwarding df-info [ ipv6-rp-address ] [ verbose ] [ slot slot-number ]

In IRF mode:

display ipv6 multicast [ vpn-instance vpn-instance-name ] forwarding df-info [ ipv6-rp-address ] [ verbose ] [ chassis chassis-number slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays DF information on the public network.

ipv6-rp-address: Specifies an RP address of IPv6 BIDIR-PIM by its IPv6 address.

verbose: Displays detailed information. If you do not specify this keyword, the command displays brief information.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays DF information for the MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device or specifies a PEX. The chassis-number argument represents the member ID of the IRF member device or the virtual chassis number of the PEX. The slot-number argument represents the slot number of the card or PEX. If you do not specify a card or PEX, this command displays DF information for the global active MPU. (In IRF mode.)

Usage guidelines

In an IPv6 BIDIR-PIM domain, only the DF on each subnet can forward IPv6 multicast data destined for an IPv6 multicast group toward the RP of the group. For more information about the DF, see IP Multicast Configuration Guide.

Examples

# Display brief DF information on the public network.

<Sysname> display ipv6 multicast forwarding df-info

Total 1 RP, 1 matched

00001. RP address: 7:11::1

Flags: 0x0

Uptime: 01:46:40

RPF interface: GigabitEthernet1/0/1

List of 1 DF interface:

1: GigabitEthernet1/0/2

# Display detailed DF information on the public network.

<Sysname> display ipv6 multicast forwarding df-info verbose

Total 1 RP, 1 matched

00001. RP address: 7:11::1

MID: 2, Flags: 0x0

Uptime: 00:03:53

Product information: 0x7a2f762f, 0x718fee9f, 0x4b82f137, 0x71c32184

RPF interface: GigabitEthernet1/0/1

Product information: 0xa567d6fc, 0xadeb03e3

Tunnel information: 0xdfb107d4, 0x7aa5d510

List of 1 DF interface:

1: GigabitEthernet1/0/2

Product information: 0xa986152b, 0xb74a9a2f

Tunnel information: 0x297ca208, 0x76985b89

Table 3 Command output

Field	Description
Total 1 RP, 1 matched	Total number of RPs and total number of matching RPs.
00001	Sequence number of the entry to which the RP is designated.
MID	ID of the entry to which the RP is designated. Each entry to which the RP is designated has a unique MID.
Flags	Entry flag. This field displays one flag or the sum of multiple flags. In this example, the value 0x0 means that the entry has only one flag 0x0. The following flags are available for an entry: · 0x0—The entry is in correct state. · 0x4—The entry fails to update. · 0x8—DF interface information fails to update for the entry. · 0x40—The entry is to be deleted. · 0x100—The entry is being deleted. · 0x200—The entry is in GR state.
Uptime	Existence duration for the entry to which the RP is designated.
RPF interface	RPF interface to the RP.
List of 1 DF interface	DF interface list.

display ipv6 multicast forwarding event

Use display ipv6 multicast forwarding event to display statistics for IPv6 multicast forwarding events.

Syntax

In standalone mode:

display ipv6 multicast [ vpn-instance vpn-instance-name ] forwarding event [ slot slot-number ]

In IRF mode:

display ipv6 multicast [ vpn-instance vpn-instance-name ] forwarding event [ chassis chassis-number slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays statistics for the IPv6 multicast forwarding events on the public network.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays statistics for the IPv6 multicast forwarding events for the MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device or specifies a PEX. The chassis-number argument represents the member ID of the IRF member device or the virtual chassis number of the PEX. The slot-number argument represents the slot number of the card or PEX. If you do not specify a card or PEX, this command displays statistics for the IPv6 multicast forwarding events for the global active MPU. (In IRF mode.)

Examples

# Display statistics for the IPv6 multicast forwarding events on the public network.

<Sysname> display ipv6 multicast forwarding event

Total entry active event sent: 0

Total entry inactive event sent: 0

Total NoCache event sent: 2

Total NoCache event dropped: 0

Total WrongIF event sent: 0

Total WrongIF event dropped: 0

Total SPT switch event sent: 0

NoCache rate limit: 1024 packets/s

WrongIF rate limit: 1 packets/10s

Total timer of register suppress timeout: 0

Table 4 Command output

Field	Description
Total entry active event sent	Number of times that the entry-active event has been sent.
Total entry inactive event sent	Number of times that the entry-inactive event has been sent.
Total NoCache event sent	Number of times that the NoCache event has been sent.
Total NoCache event dropped	Number of times that the NoCache event has been dropped.
Total WrongIF event sent	Number of times that the WrongIF event has been sent.
Total WrongIF event dropped	Number of times that the WrongIF event has been dropped.
Total SPT switch event sent	Number of times that the SPT-switch event has been sent.
NoCache rate limit	Rate limit for sending the NoCache event, in pps.
WrongIF rate limit	Rate limit for sending the WrongIF event, in packets per 10 seconds.
Total timer of register suppress timeout	Number of times that the registration suppression has timed out in total.

Related commands

reset ipv6 multicast forwarding event

display ipv6 multicast forwarding-table

Use display ipv6 multicast forwarding-table to display IPv6 multicast forwarding entries.

Syntax

In standalone mode:

display ipv6 multicast [ vpn-instance vpn-instance-name ] forwarding-table [ ipv6-source-address [ prefix-length ] | ipv6-group-address [ prefix-length ] | incoming-interface interface-type interface-number | outgoing-interface { exclude | include | match } interface-type interface-number | slot slot-number | statistics ] *

In IRF mode:

display ipv6 multicast [ vpn-instance vpn-instance-name ] forwarding-table [ ipv6-source-address [ prefix-length ] | ipv6-group-address [ prefix-length ] | chassis chassis-number slot slot-number | incoming-interface interface-type interface-number | outgoing-interface { exclude | include | match } interface-type interface-number | statistics ] *

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays IPv6 multicast forwarding entries on the public network.

ipv6-source-address: Specifies an IPv6 multicast source address.

ipv6-group-address: Specifies an IPv6 multicast group address in the range of FFxy::/16, where "x" and "y" represent any hexadecimal numbers from 0 to F.

prefix-length: Specifies an address prefix length. The default value is 128. For an IPv6 multicast group address, the value range for this argument is 8 to 128. For an IPv6 multicast source address, the value range for this argument is 0 to 128.

incoming-interface: Specifies the IPv6 forwarding entries that contain the specified incoming interface.

interface-type interface-number: Specifies an interface by its type and number.

outgoing-interface: Specifies the IPv6 forwarding entries that contain the specified outgoing interface.

exclude: Specifies the IPv6 forwarding entries that do not contain the specified interface in the outgoing interface list.

include: Specifies the IPv6 forwarding entries that contain the specified interface in the outgoing interface list.

match: Specifies the IPv6 forwarding entries that contain only the specified interface in the outgoing interface list.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays the IPv6 multicast forwarding entries for the MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device or specifies a PEX. The chassis-number argument represents the member ID of the IRF member device or the virtual chassis number of the PEX. The slot-number argument represents the slot number of the card or PEX. If you do not specify a card or PEX, this command displays IPv6 multicast forwarding entries for the global active MPU. (In IRF mode.)

statistics: Displays statistics for the IPv6 multicast forwarding table.

Examples

# Display IPv6 multicast forwarding entries on the public network.

<Sysname> display ipv6 multicast forwarding-table

Total 1 entry, 1 matched

00001. (1::1, ff0e::1)

Flags: 0x0

Uptime: 00:08:32, Timeout in: 00:03:26

Incoming interface: Vlan-interface10

Incoming sub-VLAN: VLAN 11

Outgoing sub-VLAN: VLAN 12

VLAN 13

List of 1 outgoing interface:

1: Vlan-interface20

Sub-VLAN: VLAN 21

VLAN 22

Matched 19648 packets(20512512 bytes), Wrong If 0 packet

Forwarded 19648 packets(20512512 bytes)

Table 5 Command output

Field	Description
Total 1 entry, 1 matched	Total number of (S, G) entries, and the total number of matching (S, G) entries.
00001	Sequence number of the (S, G) entry.
(1::1, ff0e::1)	(S, G) entry.
Flags	Entry flag. This field displays one flag or the sum of multiple flags. In this example, the value 0x0 means that the entry has only one flag 0x0. The following flags are available for an entry: · 0x0—The entry is in correct state. · 0x1—The entry is in inactive state. · 0x2—The entry is null. · 0x4—The entry fails to update. · 0x8—The outgoing interface information fails to update for the entry. · 0x20—A register outgoing interface is available. · 0x40—The entry is to be deleted. · 0x80—The entry is in registration suppression state. · 0x100—The entry is being deleted. · 0x200—The entry is in GR state. · 0x400—The entry has the VLAN interface of the super VLAN. · 0x800—The entry has the associated ND entry for the IPv6 multicast source address. · 0x4000000—The entry is created by the MLD proxy. · 0x20000000—The entry is an IPv6 BIDIR-PIM forwarding entry.
Uptime	Length of time for which the (S, G) entry has been up.
Timeout in	Length of time in which the (S, G) entry will time out.
Incoming interface	Incoming interface of the (S, G) entry.
Incoming sub-VLAN	Incoming sub-VLAN of the super VLAN when the incoming interface of the (S, G) entry is the VLAN interface of this super VLAN.
Outgoing sub-VLAN	Outgoing sub-VLAN of the super VLAN when the incoming interface of the (S, G) entry is the VLAN interface of this super VLAN.
List of 1 outgoing interfaces	Outgoing interface list of the (S, G) entry.
Sub-VLAN	Outgoing sub-VLAN of the super VLAN when the outgoing interface of the (S, G) entry is the VLAN interface of this super VLAN.
Matched 19648 packets (20512512 bytes), Wrong If 0 packet	Accumulated counts of sampled packets (bytes) that match the (S, G) entry and sampled packets with incoming interface errors in periodic sampling.
Forwarded 19648 packets (20512512 bytes)	Accumulated count of packets (bytes) that have been forwarded in periodic sampling.

Related commands

reset ipv6 multicast forwarding-table

display ipv6 multicast forwarding-table df-list

Use display ipv6 multicast forwarding-table df-list to display information about the DF list in the IPv6 multicast forwarding table.

Syntax

In standalone mode:

display ipv6 multicast [ vpn-instance vpn-instance-name ] forwarding-table df-list [ ipv6-group-address ] [ verbose ] [ slot slot-number ]

In IRF mode:

display ipv6 multicast [ vpn-instance vpn-instance-name ] forwarding-table df-list [ ipv6-group-address ] [ verbose ] [ chassis chassis-number slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays information about the DF list in the IPv6 multicast forwarding table on the public network.

ipv6-group-address: Specifies an IPv6 multicast address in the range of FFxy::/16, where "x" and "y" represent any hexadecimal numbers from 0 to F.

verbose: Displays detailed information. If you do not specify this keyword, the command displays brief information.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays information about the DF list in the IPv6 multicast forwarding table for the MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device or specifies a PEX. The chassis-number argument represents the member ID of the IRF member device or the virtual chassis number of the PEX. The slot-number argument represents the slot number of the card or PEX. If you do not specify a card or PEX, this command displays information about the DF list in the IPv6 multicast forwarding tables for the global active MPU. (In IRF mode.)

Examples

# Display brief information about the DF list in the IPv6 multicast forwarding table on the public network.

<Sysname> display ipv6 multicast forwarding-table df-list

Total 1 entry, 1 matched

00001. (::, FF1E::1)

List of 1 DF interface:

1: GigabitEthernet1/0/1

# Display detailed information about the DF list in the IPv6 multicast forwarding table on the public network.

<Sysname> display ipv6 multicast forwarding-table df-list verbose

Total 1 entry, 1 matched

00001. (::, FF1E::1)

List of 1 DF interface:

1: GigabitEthernet1/0/1

Product information: 0x347849f6, 0x14bd6837

Tunnel information: 0xc4857986, 0x128a9c8f

Table 6 Command output

Field	Description
Total 1 entry, 1 matched	Total number of entries, and the total number of matching entries.
00001	Sequence number of the entry.
(::, FF1E::1)	(*, G) entry.
List of 1 DF interface	DF interface list.

display ipv6 multicast routing-table

Use display ipv6 multicast routing-table to display IPv6 multicast routing entries.

Syntax

display ipv6 multicast [ vpn-instance vpn-instance-name ] routing-table [ ipv6-source-address [ prefix-length ] | ipv6-group-address [ prefix-length ] | incoming-interface interface-type interface-number | outgoing-interface { exclude | include | match } interface-type interface-number ] *

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays IPv6 multicast routing entries on the public network.

ipv6-source-address: Specifies an IPv6 multicast source address.

ipv6-group-address: Specifies an IPv6 multicast group address in the range of FFxy::/16, where "x" and "y" represent any hexadecimal numbers from 0 to F.

prefix-length: Specifies an address prefix length. The default is 128. For an IPv6 multicast group address, the value range for this argument is 8 to 128. For an IPv6 multicast source address, the value range for this argument is 0 to 128.

incoming-interface: Displays the IPv6 routing entries that contain the specified incoming interface.

interface-type interface-number: Specifies an interface by its type and number.

outgoing-interface: Displays the IPv6 routing entries that contain the specified outgoing interface.

exclude: Displays the IPv6 routing entries that do not contain the specified interface in the outgoing interface list.

include: Displays the IPv6 routing entries that contain the specified interface in the outgoing interface list.

match: Displays the IPv6 routing entries that contain only the specified interface in the outgoing interface list.

Usage guidelines

IPv6 multicast routing entries are the basis of IPv6 multicast forwarding. You can use this command to view the establishment state of (S, G) entries.

Examples

# Display IPv6 multicast routing entries on the public network.

<Sysname> display ipv6 multicast routing-table

Total 1 entry

00001. (2001::2, FFE3::101)

Uptime: 00:00:14

Upstream Interface: GigabitEthernet1/0/1

List of 2 downstream interfaces

1: GigabitEthernet1/0/2

2: GigabitEthernet1/0/3

Table 7 Command output

Field	Description
Total 1 entry	Total number of (S, G) entries.
00001	Sequence number of the (S, G) entry.
(2001::2, FFE3::101)	(S, G) entry.
Uptime	Length of time for which the (S, G) entry has been up.
Upstream Interface	Upstream interface at which the (S, G) packets should arrive.
List of 2 downstream interfaces	List of downstream interfaces that need to forward (S, G) packets.

Related commands

reset ipv6 multicast routing-table

display ipv6 multicast rpf-info

Use display ipv6 multicast rpf-info to display RPF information for an IPv6 multicast source.

Syntax

display ipv6 multicast [ vpn-instance vpn-instance-name ] rpf-info ipv6-source-address [ ipv6-group-address ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays RPF information for an IPv6 multicast source on the public network.

ipv6-source-address: Specifies an IPv6 multicast source address.

ipv6-group-address: Specifies an IPv6 multicast group address in the range of FFxy::/16 (excluding FFx0::/16, FFx1::/16, FFx2::/16, and FF0y::), where "x" and "y" represent any hexadecimal numbers from 0 to F.

Examples

# Display RPF information for the multicast source 2001::101 on the public network.

<Sysname> display ipv6 multicast rpf-info 2001::101

RPF information about source 2001::101:

RPF interface: GigabitEthernet1/0/1, RPF neighbor: FE80::A01:101:1

Referenced prefix/prefix length: 2001::/64

Referenced route type: igp

Route selection rule: preference-preferred

Load splitting rule: disable

Table 8 Command output

Field	Description
RPF information about source 2001::101	RPF information of the IPv6 multicast source 2001::101.
RPF interface	Type and number of the RPF interface.
RPF neighbor	IPv6 address (link-local address) of the RPF neighbor.
Referenced prefix/prefix length	Referenced route and its prefix length.
Referenced route type	Type of the referenced route: · igp—IPv6 IGP unicast route. · egp—IPv6 EGP unicast route. · unicast (direct) —IPv6 directly connected unicast route. · unicast—Other IPv6 unicast route, such as IPv6 unicast static route. · mbgp—IPv6 MBGP route.
Route selection rule	RPF route selection rule: · Route preference. · Longest prefix match.
Load splitting rule	Whether the load sharing rule is enabled.

Related commands

· display ipv6 multicast forwarding-table

· display ipv6 multicast routing-table

ipv6 multicast boundary

Use ipv6 multicast boundary to configure an IPv6 multicast forwarding boundary.

Use undo ipv6 multicast boundary to delete an IPv6 multicast forwarding boundary.

Syntax

ipv6 multicast boundary { ipv6-group-address prefix-length | scope { scope-id | admin-local | global | organization-local | site-local } }

undo ipv6 multicast boundary { ipv6-group-address prefix-length| all | scope { scope-id | admin-local | global | organization-local | site-local } }

Default

An interface is not an IPv6 multicast forwarding boundary.

Views

Interface view

Predefined user roles

network-admin

mdc-admin

Parameters

ipv6-group-address: Specifies an IPv6 multicast group address in the range of FFxy::/16, where "x" and "y" represent any hexadecimal numbers from 0 to F.

prefix-length: Specifies the address prefix length in the range of 8 to 128.

all: Specifies all IPv6 multicast boundaries configured on the interface.

scope-id: Specifies the ID of an admin-scoped zone, in the range of 3 to 15, which is identified by the scope field in the IPv6 multicast group address.

admin-local: Specifies the scope zone as admin-local, which has a scope ID of 4.

global: Specifies the scope zone as global, which has a scope ID of 14.

organization-local: Specifies the scope zone as organization-local, which has a scope ID of 8.

site-local: Specifies the scope zone as site-local, which has a scope ID of 5.

Usage guidelines

An IPv6 multicast forwarding boundary sets the boundary condition for the IPv6 multicast groups in the specified address range. If the destination address of an IPv6 multicast packet matches the set boundary condition, the packet is not forwarded.

An interface can act as a forwarding boundary for multiple IPv6 multicast groups in different address ranges. You can implement this by using this command on the interface for each multicast address range. These multicast groups must be in the same scope. The latest configuration of a scope overwrites the previous one.

Assume that Set A and Set B are both IPv6 multicast forwarding boundary sets with different address ranges, and that B is a subset of A. A takes effect on the interface no matter whether A is configured earlier or later than B

Examples

# Configure VLAN-interface 100 to be the forwarding boundary of IPv6 multicast groups in the range of FF03::/16.

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] ipv6 multicast boundary ff03:: 16

# Configure VLAN-interface 100 to be the forwarding boundary of IPv6 multicast groups in the admin-local scope.

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] ipv6 multicast boundary scope 4

Related commands

display ipv6 multicast boundary

ipv6 multicast forwarding supervlan community

Use ipv6 multicast forwarding supervlan community to enable IPv6 multicast forwarding between sub-VLANs that are associated with a super VLAN.

Use undo ipv6 multicast forwarding supervlan community to disable IPv6 multicast forwarding between sub-VLANs that are associated with a super VLAN.

Syntax

ipv6 multicast forwarding supervlan community

undo ipv6 multicast forwarding supervlan community

Default

IPv6 multicast data cannot be forwarded between sub-VLANs that are associated with a super VLAN.

Views

VLAN interface view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

After you execute the ipv6 multicast forwarding supervlan community command, you must clear all IPv6 multicast forwarding entries with the super VLAN interface as the incoming interface. Otherwise, this command cannot take effect. To clear the required multicast forwarding entries, use the reset ipv6 multicast forwarding-table command.

Examples

# Enable IPv6 multicast forwarding between sub-VLANs that are associated with super VLAN 2.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] ipv6 multicast forwarding supervlan community

Related commands

reset ipv6 multicast forwarding-table

ipv6 multicast routing

Use ipv6 multicast routing to enable IPv6 multicast routing and enter IPv6 MRIB view.

Use undo ipv6 multicast routing to disable IPv6 multicast routing.

Syntax

ipv6 multicast routing [ vpn-instance vpn-instance-name ]

undo ipv6 multicast routing [ vpn-instance vpn-instance-name ]

Default

IPv6 multicast routing is disabled.

Views

System view

Predefined user roles

network-admin

mdc-admin

parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command enables IPv6 multicast routing on the public network.

Usage guidelines

Other Layer 3 IPv6 multicast commands take effect only when IPv6 multicast routing is enabled.

The switch does not forward IPv6 multicast packets before IPv6 multicast routing is enabled.

Examples

# Enable IPv6 multicast routing and enter IPv6 MRIB view on the public network.

<Sysname> system-view

[Sysname] ipv6 multicast routing

[Sysname-mrib6]

# Enable IPv6 multicast routing and enter IPv6 MRIB view in VPN instance mvpn.

<Sysname> system-view

[Sysname] ipv6 multicast routing vpn-instance mvpn

[Sysname-mrib6-mvpn]

load-splitting (IPv6 MRIB view)

Use load-splitting to enable load splitting of IPv6 multicast traffic.

Use multicast load-splitting to restore the default.

Syntax

load-splitting { source | source-group }

undo load-splitting

Default

Load splitting of IPv6 multicast traffic is disabled.

Views

IPv6 MRIB view

Predefined user roles

network-admin

mdc-admin

Parameters

source: Specifies IPv6 multicast load splitting on a per-source basis.

source-group: Specifies IPv6 multicast load splitting on a per-source basis and on a per-group basis.

Usage guidelines

This command does not take effect on IPv6 BIDIR-PIM.

Examples

# Enable load splitting of IPv6 multicast traffic on a per-source basis on the public network.

<Sysname> system-view

[Sysname] ipv6 multicast routing

[Sysname-mrib6] load-splitting source

longest-match (IPv6 MRIB view)

Use longest-match to specify the longest prefix match principle for RPF route selection.

Use undo longest-match to restore the default.

Syntax

longest-match

undo longest-match

Default

Route preference is used for RPF route selection.

Views

IPv6 MRIB view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

This command enables the switch to use the matching route with the longest prefix as the RPF route.

Examples

# Specify the longest prefix match principle for RPF route selection on the public network.

<Sysname> system-view

[Sysname] ipv6 multicast routing

[Sysname-mrib6] longest-match

reset ipv6 multicast forwarding event

Use reset ipv6 multicast forwarding event to clear statistics for IPv6 multicast forwarding events.

Syntax

reset ipv6 multicast [ vpn-instance vpn-instance-name ] forwarding event

Views

User view

Predefined user roles

network-admin

mdc-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command clears statistics for the IPv6 multicast forwarding events on the public network.

Examples

# Clear statistics for the IPv6 multicast forwarding events on the public network.

<Sysname> reset ipv6 multicast forwarding event

Related commands

display ipv6 multicast forwarding event

reset ipv6 multicast forwarding-table

Use reset ipv6 multicast forwarding-table to clear IPv6 multicast forwarding entries.

Syntax

reset ipv6 multicast [ vpn-instance vpn-instance-name ] forwarding-table { { ipv6-source-address [ prefix-length ] | ipv6-group-address [ prefix-length ] | incoming-interface { interface-type interface-number } } * | all }

Views

User view

Predefined user roles

network-admin

mdc-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command clears IPv6 multicast forwarding entries on the public network.

ipv6-source-address: Specifies an IPv6 multicast source address.

ipv6-group-address: Specifies an IPv6 multicast group address in the range of FFxy::/16, where "x" and "y" represent any hexadecimal numbers from 0 to F.

prefix-length: Specifies the address prefix length. The default value is 128. For an IPv6 multicast group address, the value range for this argument is 8 to 128. For an IPv6 multicast source address, the value range for this argument is 0 to 128.

incoming-interface: Specifies the IPv6 multicast forwarding entries that contain the specified incoming interface.

interface-type interface-number: Specifies an interface by its type and number.

all: Specifies all forwarding entries in the IPv6 multicast forwarding table.

Usage guidelines

When an IPv6 multicast forwarding entry is cleared, the associated IPv6 multicast routing entry is also cleared.

Examples

# Clear the IPv6 multicast forwarding entry for IPv6 multicast group FF0E::1 on the public network.

<Sysname> reset ipv6 multicast forwarding-table ff0e::1

Related commands

display ipv6 multicast forwarding-table

reset ipv6 multicast routing-table

Use reset ipv6 multicast routing-table to clear IPv6 multicast routing entries.

Syntax

reset ipv6 multicast [ vpn-instance vpn-instance-name ] routing-table { { ipv6-source-address [ prefix-length ] | ipv6-group-address [ prefix-length ] | incoming-interface interface-type interface-number } * | all }

Views

User view

Predefined user roles

network-admin

mdc-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command clears IPv6 multicast routing entries on the public network.

ipv6-source-address: Specifies an IPv6 multicast source address.

ipv6-group-address: Specifies an IPv6 multicast group address in the range of FFxy::/16, where "x" and "y" represent any hexadecimal numbers from 0 to F.

incoming-interface: Specifies the IPv6 multicast routing entries that contain the specified incoming interface.

interface-type interface-number: Specifies an interface by its type and number.

all: Specifies all IPv6 multicast routing entries.

Usage guidelines

When an IPv6 multicast routing entry is cleared, the associated IPv6 multicast forwarding entry is also cleared.

Examples

# Clear the IPv6 multicast routing entry for IPv6 multicast group FF03::101 on the public network.

<Sysname> reset ipv6 multicast routing-table ff03::101

Related commands

display ipv6 multicast routing-table

07-IP Multicast Command Reference

display ipv6 mrib interface

display ipv6 multicast forwarding event

ipv6 multicast forwarding supervlan community

load-splitting (IPv6 MRIB view)

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

News & Events

Contact Us