Login
- Table of Contents
- Related Documents
-
| Title | Size | Download |
|---|---|---|
| 01-Ethernet interface commands | 191.76 KB |
Contents
Common Ethernet interface commands
Layer 2 Ethernet interface/subinterface commands
Layer 3 Ethernet interface or subinterface commands
· When enhanced IRF is enabled on a switch operating in IRF mode, you cannot create Layer 3 Ethernet interfaces, Layer 3 Ethernet subinterfaces, Layer 3 aggregate interfaces, or Layer 3 aggregate subinterfaces on the switch. For more information about IRF, see IRF Configuration Guide.
Common Ethernet interface commands
default
Use default to restore the default settings for an Ethernet interface or subinterface.
Syntax
default
Views
Ethernet interface view, Ethernet subinterface view
Predefined user roles
network-admin
mdc-admin
Usage guidelines
|
|
CAUTION: The default command might interrupt ongoing network services. Make sure you are fully aware of the impacts of this command when you use it in a live network. |
This command might fail to restore the default settings for some commands for reasons such as command dependencies and system restrictions. Use the display this command in interface view to identify these commands, and then use their undo forms or follow the command reference to individually restore their default settings. If your restoration attempt still fails, follow the error message instructions to resolve the problem.
Examples
# Restore the default settings for interface GigabitEthernet 3/0/1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] default
# Restore the default settings for Layer 3 subinterface GigabitEthernet 3/0/1.1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1.1
[Sysname-GigabitEthernet3/0/1.1] default
description
Use description to change the description of an interface.
Use undo description to restore the default.
Syntax
description text
undo description
Default
The description of an interface is the interface name plus Interface (for example, GigabitEthernet3/0/1 Interface).
Views
Ethernet interface view, Ethernet subinterface view
Predefined user roles
network-admin
mdc-admin
Parameters
text: Specifies the interface description, a case-sensitive string of 1 to 80 characters.
Examples
# Change the description of interface GigabitEthernet 3/0/1 to lanswitch-interface.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] description lanswitch-interface
# Change the description of Ethernet subinterface GigabitEthernet 3/0/1.1 to l2-subinterface3/0/1.1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1.1
[Sysname-GigabitEthernet3/0/1.1] description l2-subinterface3/0/1.1
display counters
Use display counters to display interface traffic statistics.
Syntax
display counters { inbound | outbound } interface [ interface-type [ interface-number | interface-number.subnumber ] ]
Views
Any view
Predefined user roles
network-admin
network-operator
mdc-admin
mdc-operator
Parameters
inbound: Displays inbound traffic statistics.
outbound: Displays outbound traffic statistics.
interface-type: Specifies an interface type.
interface-number: Specifies an interface number.
interface-number.subnumber: Specifies a subinterface number, where interface-number is a main interface (which must be a Layer 3 Ethernet interface) number, and subnumber is the number of a subinterface created under the interface. The value range for the subnumber argument is 1 to 4094.
Usage guidelines
This command displays traffic statistics within a statistics polling interval specified by the flow-interval command.
To clear the Ethernet interface traffic statistics, use the reset counters interface command. For more information, see "reset counters interface."
If no interface type is specified, this command displays traffic statistics for all interfaces that have traffic counters.
If an interface type is specified but no interface number or subinterface number is specified, this command displays traffic statistics for all interfaces of the specified type.
If an interface type and an interface number or subinterface number are specified, this command displays traffic statistics of the specified interface or subinterface.
Examples
# Display inbound traffic statistics for all GigabitEthernet interfaces.
<Sysname> display counters inbound interface GigabitEthernet
Interface Total (pkts) Broadcast (pkts) Multicast (pkts) Err (pkts)
GE3/0/1 100 100 0 0
GE3/0/2 0 0 0 0
GE3/0/3 Overflow Overflow Overflow Overflow
GE3/0/4 0 0 0 0
......
Overflow: More than 14 digits (7 digits for column "Err").
--: Not supported.
Table 1 Command output
|
Field |
Description |
|
Interface |
Abbreviated interface name. |
|
Total (pkts) |
Total number of packets received or sent through the interface. |
|
Broadcast (pkts) |
Total number of broadcast packets received or sent through the interface. |
|
Multicast (pkts) |
Total number of multicast packets received or sent through the interface. |
|
Err (pkts) |
Total number of error packets received or sent through the interface. |
|
Overflow: More than 14 digits (7 digits for column "Err") |
The command displays Overflow if any of the following cases applies: · The data length of an Err field value is greater than 7 decimal digits. · The data length of a non-Err field value is greater than 14 decimal digits. |
|
--: Not supported |
The statistical item is not supported. |
Related commands
· flow-interval
· reset counters interface
display counters rate
Use display counters rate to display traffic rate statistics of interfaces in up state over the last statistics polling interval.
Syntax
display counters rate { inbound | outbound } interface [ interface-type [ interface-number | interface-number.subnumber ] ]
Views
Any view
Predefined user roles
network-admin
network-operator
mdc-admin
mdc-operator
Parameters
inbound: Displays inbound traffic rate statistics.
outbound: Displays outbound traffic rate statistics.
interface-type: Specifies an interface type.
interface-number: Specifies an interface number.
interface-number.subnumber: Specifies a subinterface number, where interface-number is a main interface (which must be a Layer 3 Ethernet interface) number, and subnumber is the number of a subinterface created under the interface. The value range for the subnumber argument is 1 to 4094.
Usage guidelines
The statistics cover only interfaces in up state.
If an interface type is specified, the command displays traffic rate statistics for all up interfaces of the specified type over the last statistics polling interval.
If no interface type is specified, the command displays traffic rate statistics for all up interfaces that have traffic counters over the last statistics polling interval.
If an interface which is always down over the last statistics polling interval is specified, the system prompts that the interface does not support the command.
You can use the flow-interval command to set the statistics polling interval.
Examples
# Display the inbound traffic rate statistics for all GigabitEthernet interfaces.
<Sysname> display counters rate inbound interface gigabitethernet
Interface Total (pps) Broadcast (pps) Multicast (pps)
GE3/0/1 200 100 100
GE3/0/2 300 200 100
GE3/0/3 300 200 100
......
Overflow: More than 14 digits.
--: Not supported.
Table 2 Command output
|
Field |
Description |
|
Interface |
Abbreviated interface name. |
|
Total (pkts/sec) |
Average rate (in pps) of receiving or sending packets during the statistics polling interval. |
|
Broadcast (pkts/sec) |
Average rate (in pps) of receiving or sending broadcast packets during the statistics polling interval. |
|
Multicast (pkts/sec) |
Average rate (in pps) of receiving or sending multicast packets during the statistics polling interval. |
|
Overflow: more than 14 decimal digits |
The command displays Overflow if the data length of a statistical item is greater than 14 decimal digits. |
|
--: not supported |
The statistical item is not supported. |
Related commands
· flow-interval
· reset counters interface
display interface
Use display interface to display Ethernet interface information.
Syntax
display interface [ interface-type [ interface-number | interface-number.subnumber ] ]
Views
Any view
Predefined user roles
network-admin
network-operator
mdc-admin
mdc-operator
Parameters
interface-type: Specifies an interface type.
interface-number: Specifies an interface number.
interface-number.subnumber: Specifies a subinterface number, where interface-number is a main interface (which must be a Layer 3 Ethernet interface) number, and subnumber is the number of a subinterface created under the interface. The value range for the subnumber argument is 1 to 4094.
Usage guidelines
If no interface type is specified, this command displays information about all interfaces.
If an interface type is specified but no interface number or subinterface number is specified, this command displays information about all interfaces of that type.
If both the interface type and interface number are specified, this command displays information about the specified interface.
Examples
# Display information about Layer 3 interface GigabitEthernet 3/0/1.
<Sysname> display interface GigabitEthernet 3/0/1
GigabitEthernet3/0/1 current state: DOWN
Line protocol current state: DOWN
Description: GigabitEthernet3/0/1 Interface
The Maximum Transmit Unit is 100, Hold timer is 10(sec)
Internet protocol processing: disabled
IP Packet Frame Type:PKTFMT_ETHNT_2, Hardware Address: 0001-0001-0001
IPV6 Packet Frame Type:PKTFMT_ETHNT_2, Hardware Address: 0001-0001-0001
Media type is twisted pair, Port hardware type is 1000_BASE_T
Port priority: 2
Loopback is not set
Unknown-speed mode, Unknown-duplex mode
Last 300 seconds input: 0 packets/sec 0 bytes/sec 0
Last 300 seconds output: 0 packets/sec 0 bytes/sec 0
Input (total): 0 packets, 0 bytes
0 broadcasts, 0 multicasts, - pauses
Input (normal): 0 packets, 0 bytes
0 broadcasts, 0 multicasts, 0 pauses
Input: 0 input errors, 0 runts, 0 giants, 0 throttles
0 CRC, 0 frame, 0 overruns, - aborts
- ignored, - parity errors
Output (total): 0 packets, 0 bytes
0 broadcasts, 0 multicasts, - pauses
Output (normal): 0 packets, 0 bytes
0 broadcasts, 0 multicasts, 0 pauses
Output: 0 output errors, - underruns, - buffer failures
0 aborts, 0 deferred, 0 collisions, 0 late collisions
- lost carrier, - no carrier
Peak value of input: 0 bytes/sec, at 2011-12-23 09:05:58
Peak value of output: 0 bytes/sec, at 2011-12-23 09:05:58
Table 3 Command output
|
Field |
Description |
|
GigabitEthernet3/0/1 current state |
State of the interface: · Administratively DOWN—The Ethernet interface was shut down with the shutdown command. The interface is administratively down. · DOWN—The Ethernet interface is administratively up but physically down (possibly because no physical link is present or the link has failed). · UP—The Ethernet interface is both administratively and physically up. |
|
Line protocol current state |
Link layer state of the interface. The state is determined through parameter negotiation on the link layer. |
|
Hold timer is |
Link-up or link-down event suppression interval. |
|
Internet protocol processing: disabled |
Indicates that the interface cannot process IP packets. |
|
Media type |
Physical media type of the interface: · twisted pair · optical fiber |
|
Loopback is set internal |
An internal loopback test is running on the Ethernet interface. |
|
Loopback is not set |
No loopback test is running on the Ethernet interface. |
|
Unknown-speed mode |
The speed of the interface is unknown, because the speed negotiation fails or the interface is not physically connected. |
|
Unknown-duplex mode |
The duplex mode of the interface is unknown, because the duplex mode negotiation fails or the interface is not physically connected. |
|
Last 300 seconds input rate |
Average input rate over the last 300 seconds in Bps, bps, and pps. You can use the flow-interval command to set the statistics polling interval. |
|
Last 300 seconds output rate |
Average output rate over the last 300 seconds in Bps, bps, and pps. You can use the flow-interval command to set the statistics polling interval. |
|
Input (total): Input (normal): Input: Output (total): Output (normal): Output: |
Statistics about input/output packets and errors. For more information, see Table 4. A hyphen (-) indicates that the statistical item is not supported. |
|
Peak value of input |
Peak rate of inbound traffic in Bps, and the time when the peak inbound traffic rate occurred. |
|
Peak value of output |
Peak rate of outbound traffic in Bps, and the time when the peak outbound traffic rate occurred. |
# Display detailed information about Layer 2 interface GigabitEthernet 3/0/1.
<Sysname> display interface GigabitEthernet 3/0/1
GigabitEthernet3/0/1 current state: DOWN
Line protocol current state: DOWN
IP Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: 000c-2963-b767
Description: GigabitEthernet3/0/1 Interface
Loopback is not set
Media type is twisted pair, Port hardware type is 1000_BASE_T
1000Mbps-speed mode, full-duplex mode
Link speed type is autonegotiation, link duplex type is autonegotiation
Flow-control is not enabled
The Maximum Frame Length is 9216
Allow jumbo frame to pass
Broadcast MAX-ratio: 100%
Multicast MAX-ratio: 100%
Unicast MAX-ratio: 100%
PVID: 1
Mdi type: automdix
Port link-type: access
Tagged Vlan: none
UnTagged Vlan: 1
Port priority: 2
Last clearing of counters: Never
Peak value of input: 0 bytes/sec, at 2000-01-01 00:00:00
Peak value of output: 0 bytes/sec, at 2000-01-01 00:00:00
Last 300 seconds input: 0 packets/sec 0 bytes/sec 0%
Last 300 seconds output: 0 packets/sec 0 bytes/sec 0%
Input (total): 0 packets, 0 bytes
0 unicasts, 0 broadcasts, 0 multicasts, - pauses
Input (normal): 0 packets, 0 bytes
0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
Input: 0 input errors, 0 runts, 0 giants, 0 throttles
0 CRC, 0 frame, 0 overruns, - aborts
- ignored, - parity errors
Output (total): 0 packets, 0 bytes
0 unicasts, 0 broadcasts, 0 multicasts, - pauses
Output (normal): 0 packets, 0 bytes
0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
Output: 0 output errors, - underruns, - buffer failures
0 aborts, 0 deferred, 0 collisions, 0 late collisions
- lost carrier, - no carrier
|
Field |
Description |
|
GigabitEthernet3/0/1 current state |
State of the Ethernet interface: · Administratively DOWN—The Ethernet interface was shut down with the shutdown command. The interface is administratively down. · DOWN—The Ethernet interface is administratively up but physically down (possibly because no physical link is present or the link has failed). · UP—The Ethernet interface is both administratively and physically up. |
|
Line protocol current state |
Link layer state of the interface. The state is determined through parameter negotiation on the link layer. |
|
IP Packet Frame Type |
Ethernet framing format. PKTFMT_ETHNT_2 indicates that the frames are encapsulated in Ethernet II framing format. |
|
Hardware address |
MAC address of the interface. |
|
Loopback is set internal |
An internal loopback test is running on the Ethernet interface. |
|
Loopback is not set |
No loopback test is running on the Ethernet interface. |
|
Media type |
Physical media type of the interface: · twisted pair · optical fiber |
|
10Mbps-speed mode |
The interface is operating at 10 Mbps. |
|
100Mbps-speed mode |
The interface is operating at 100 Mbps. |
|
1000Mbps-speed mode |
The interface is operating at 1000 Mbps. |
|
Unknown-speed mode |
The speed of the interface is unknown because the speed negotiation fails or the interface is physically disconnected. |
|
half-duplex mode |
The interface is operating in half duplex mode. |
|
full-duplex mode |
The interface is operating in full duplex mode. |
|
unknown-duplex mode |
The duplex mode of the interface is unknown because the duplex mode negotiation fails or the interface is physically disconnected. |
|
Link speed type is autonegotiation |
The interface is configured with the speed auto command. |
|
Link speed type is force link |
The interface is configured with a specific speed, for example, 10 Mbps or 100 Mbps, by using the speed command. |
|
link duplex type is autonegotiation |
The interface is configured with the duplex auto command. |
|
link duplex type is force link |
The interface is configured with a specific duplex mode, for example, half or full, by using the duplex command. |
|
Flow-control is not enabled |
Flow control is not enabled on the interface. |
|
The Maximum Frame Length |
Maximum Ethernet frame length allowed on the interface. |
|
Allow jumbo frame to pass |
The interface allows jumbo frames to pass through. |
|
Broadcast MAX- |
Broadcast storm suppression threshold in ratio, pps, or kbps. The unit of the threshold depends on your configuration. |
|
Multicast MAX- |
Multicast storm suppression threshold in ratio, pps, or kbps. The unit of the threshold depends on your configuration. |
|
Unicast MAX- |
Unicast storm suppression threshold in ratio, pps, or kbps. The unit of the threshold depends on your configuration. |
|
PVID |
Port VLAN ID (PVID) of the Ethernet interface. |
|
Mdi type |
Cable type (depending on your configuration): · automidx. · mdi. · mdix. |
|
Port link-type |
Link type of the interface (depending on your configuration): · access. · trunk. · hybrid. |
|
Tagged VLAN ID |
VLANs for which the interface sends packets without removing VLAN tags. |
|
Untagged VLAN ID |
VLANs for which the interface sends packets after removing VLAN tags. |
|
Port priority |
Priority of the interface. |
|
Last clearing of counters: Never |
Time when the reset counters interface command was last used to clear statistics on the interface. Never indicates that the reset counters interface command was never used since the device was started. |
|
Peak value of input |
Peak rate of inbound traffic in Bps, and the time when the peak inbound traffic rate occurred. |
|
Peak value of output |
Peak rate of outbound traffic in Bps, and the time when the peak outbound traffic rate occurred. |
|
Last 300 seconds input: 0 packets/sec 0 bytes/sec -% Last 300 seconds output: 0 packets/sec 0 bytes/sec -% |
Average rate of inbound and outbound traffic in the last 300 seconds, in pps and Bps, and the ratio of the actual rate to the maximum interface rate. A hyphen (-) indicates that the statistical item is not supported. |
|
Input(total): 0 packets, 0 bytes 0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses |
Inbound traffic statistics (in packets and bytes) for the interface. All inbound normal and abnormal packets and normal pause frames were counted. Number of inbound unicast packets, number of inbound broadcasts, number of inbound multicasts, and number of inbound pause frames. A hyphen (-) indicates that the statistical item is not supported. |
|
Input(normal): 0 packets, 0 bytes 0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses |
Inbound normal traffic and pause frame statistics (in packets and bytes) for the interface. Number of inbound normal unicast packets, number of inbound normal broadcasts, number of inbound normal multicasts, and number of inbound normal pause frames. A hyphen (-) indicates that the statistical item is not supported. |
|
input errors |
Number of inbound packets with errors. |
|
runts |
Number of inbound frames shorter than 64 bytes, in correct format, and containing valid CRCs. |
|
giants |
Number of inbound frames larger than the maximum frame length supported on the interface. · For an Ethernet interface that does not permit jumbo frames, giants refer to frames larger than 1518 bytes (without VLAN tags) or 1522 bytes (with VLAN tags). · For an Ethernet interface that permits jumbo frames, giants refer to frames larger than the maximum length of Ethernet frames that are allowed to pass through, which is configured when you configure jumbo frame support on the interface. |
|
throttles |
Number of times the port is shut down due to buffer or CPU overload. |
|
CRC |
Total number of inbound frames that had a normal length, but contained CRC errors. |
|
frame |
Total number of inbound frames that contained CRC errors and a non-integer number of bytes. |
|
overruns |
Number of packets dropped because the input rate of the port exceeded the queuing capability. |
|
aborts |
Total number of illegal inbound packets: · Fragment frames—CRC error frames shorter than 64 bytes. The length can be an integral or non-integral value. · Jabber frames—CRC error frames greater than the maximum frame length supported on the Ethernet interface (with an integral or non-integral length). For an Ethernet interface that does not permit jumbo frames, jabber frames refer to CRC error frames greater than 1518 bytes (without VLAN tags) or 1522 bytes (with VLAN tags). For an Ethernet interface that permits jumbo frames, jabber frames refer to CRC error frames greater than the maximum length of Ethernet frames that are allowed to pass through the interface (which is configured when you configure jumbo frame support on the interface). · Symbol error frames—Frames that contained at least one undefined symbol. · Unknown operation code frames—Non-pause MAC control frames. · Length error frames—Frames whose 802.3 length fields did not match the actual frame length (46 to 1500 bytes). |
|
ignored |
Number of inbound frames dropped because the receive buffer of the port ran low. |
|
parity errors |
Total number of frames with parity errors. |
|
Output(total): 0 packets, 0 bytes 0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses |
Outbound traffic statistics (in packets and bytes) for the interface. All outbound normal and abnormal packets and normal pause frames were counted. Number of outbound unicast packets, number of outbound broadcasts, number of outbound multicasts, and number of outbound pause frames. A hyphen (-) indicates that the statistical item is not supported. |
|
Output(normal): 0 packets, 0 bytes 0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses |
Outbound normal traffic and pause frame statistics (in packets and bytes) for the interface. Number of outbound normal unicast packets, number of outbound normal broadcasts, number of outbound normal multicasts, and number of outbound normal pause frames. A hyphen (-) indicates that the statistical item is not supported. |
|
output errors |
Number of outbound packets with errors. |
|
underruns |
Number of packets dropped because the output rate of the interface exceeded the output queuing capability. This is a low-probability hardware anomaly. |
|
buffer failures |
Number of packets dropped because the transmit buffer of the interface ran low. |
|
aborts |
Number of packets that failed to be transmitted, for example, because of Ethernet collisions. |
|
deferred |
Number of frames that the interface deferred to transmit because of detected collisions. |
|
collisions |
Number of frames that the interface stopped transmitting because Ethernet collisions were detected during transmission. |
|
late collisions |
Number of frames that the interface deferred to transmit after transmitting their first 512 bits because of detected collisions. |
|
lost carrier |
Number of carrier losses during transmission. This counter increases by one when a carrier is lost, and applies to serial WAN interfaces. |
|
no carrier |
Number of times that the port failed to detect the carrier when attempting to send frames. This counter increases by one when a port failed to detect the carrier, and applies to serial WAN interfaces. |
Related commands
reset counters interface
display interface brief
Use display interface brief to display brief Ethernet interface information.
Syntax
display interface [ interface-type [ interface-number | interface-number.subnumber ] ] brief [ description ]
Views
Any view
Predefined user roles
network-admin
network-operator
mdc-admin
mdc-operator
Parameters
interface-type: Specifies an interface type.
interface-number: Specifies an interface number.
interface-number.subnumber: Specifies a subinterface number, where interface-number is a main interface (which must be a Layer 3 Ethernet interface) number, and subnumber is the number of a subinterface created under the interface. The value range for the subnumber argument is 1 to 4094.
description: Displays the full description of the specified interface. If the keyword is not specified, the command displays at most the first 27 characters of the interface description. If the keyword is specified, the command displays all characters of the interface description.
Usage guidelines
If no interface type is specified, this command displays information about all interfaces.
If an interface type is specified but no interface number or subinterface number is specified, this command displays information about all interfaces of that type.
If both the interface type and interface number are specified, this command displays information about the specified interface.
Examples
# Display brief information about all interfaces.
<Sysname> display interface brief
The brief information of interface(s) under route mode:
Link: ADM - administratively down; Stby - standby
Protocol: (s) - spoofing
Interface Link Protocol Main IP Description
GE3/0/1 UP UP 10.1.1.2 Link to CoreRouter
GE3/0/2 Stby DOWN --
Loop0 UP UP(s) 2.2.2.9
NULL0 UP UP(s) --
Vlan1 UP DOWN --
Vlan999 UP UP 192.168.1.42
The brief information of interface(s) under bridge mode:
Link: ADM - administratively down
Speed or Duplex: (a)/A - auto; H - half; F - full
Type: A - access; T - trunk; H - hybrid
Interface Link Speed Duplex Type PVID Description
GE3/0/2 DOWN auto A A 1
GE3/0/3 UP 100M(a) F(a) A 1 aaaaaaaaaaaaaaaaaaaaaaaaaaa
GE3/0/4 DOWN auto A A 1
GE3/0/5 DOWN auto A A 1
GE3/0/6 UP 100M(a) F(a) A 1
GE3/0/7 DOWN auto A A 1
GE3/0/8 UP 100M(a) F(a) A 1
GE3/0/9 UP 100M(a) F(a) A 999
# Display brief information about interface GigabitEthernet 3/0/3, including the full description of the interface.
<Sysname> display interface brief GigabitEthernet 3/0/3 description
The brief information of interface(s) under bridge mode:
Link: ADM - administratively down
Speed or Duplex: (a)/A - auto; H - half; F - full
Type: A - access; T - trunk; H - hybrid
Interface Link Speed Duplex Type PVID Description
GE3/0/3 UP 100M(a) F(a) A 1 aaaaaaaaaaaaaaaaaaaaaaaaaaaaa
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
Table 5 Command output
|
Field |
Description |
|
The brief information of interface(s) under route mode: |
Brief information about Layer 3 interfaces. |
|
Link: ADM - administratively down; Stby - standby |
· ADM—The interface has been shut down by the network administrator. To recover its physical layer state, run the undo shutdown command. · Stby—The interface is a standby interface. |
|
Protocol: (s) – spoofing |
If the network layer protocol of an interface is UP, but its link is an on-demand link or not present at all, this field displays UP (s), where s represents the spoofing flag. This attribute is typical of interface Null 0 and loopback interfaces. |
|
Interface |
Interface name. |
|
Link |
Physical link state of the interface: · UP—The link is up. · DOWN—The link is physically down. · ADM—The link has been administratively shut down. To recover its physical state, run the undo shutdown command. · Stby—The interface is a standby interface. |
|
Protocol |
Protocol connection state of the interface: · UP. · DOWN. · UP(s)—The link of the interface is an on-demand link or not present at all. |
|
Description |
Interface description configured by using the description command. If the description keyword is not specified in the display interface brief command, the Description field displays at most 27 characters. If the description keyword is specified in the display interface brief command, the field displays the full interface description. |
|
The brief information of interface(s) under bridge mode: |
Brief information about Layer 2 interfaces. |
|
Speed or Duplex: (a)/A - auto; H - half; F – full |
If the speed of an interface is automatically negotiated, its speed attribute includes the auto negotiation flag, indicated by the letter a in parentheses. If the duplex mode of an interface is automatically negotiated, its duplex mode attribute includes the following options: · (a)/A—Auto negotiation. · H—Half negotiation. · F—Full negotiation. |
|
Type: A - access; T - trunk; H – hybrid |
Link type options for Ethernet interfaces. |
|
Speed |
Interface rate, in bps. |
|
Duplex |
Duplex mode of the interface: · A—Autonegotiation. · F—Full duplex. · F(a)—Autonegotiated full duplex. · H—Half duplex. · H(a)—Autonegotiated half duplex. |
|
Type |
Link type of the interface: · A—Access. · H—Hybrid. · T—Trunk. |
|
PVID |
Port VLAN ID. |
|
Cause |
Causes for the physical state of an interface to be DOWN. · Not connected—No physical connection exists (possibly because the network cable is disconnected or faulty). · Administratively DOWN—The port was shut down with the shutdown command. To restore the physical state of the interface, use the undo shutdown command. |
display packet-drop
Use display packet-drop to display information about packets dropped on an interface or multiple interfaces.
Syntax
display packet-drop { interface [ interface-type [ interface-number ] ] | summary }
Views
Any view
Predefined user roles
network-admin
network-operator
mdc-admin
mdc-operator
Parameters
interface-type: Specifies an interface type. If you do not specify an interface type, this command displays information about dropped packets on all the interfaces on the device.
interface-number: Specifies an interface number. If you specify an interface type only, this command displays information about dropped packets on the specified type of interfaces.
summary: Displays the summary of dropped packets on all interfaces.
Examples
# Display information about dropped packets on GigabitEthernet 3/0/1.
<Sysname> display packet-drop interface GigabitEthernet 3/0/1
GigabitEthernet3/0/1:
Packets dropped due to full GBP or insufficient bandwidth: 301
Packets dropped due to Fast Filter Processor FFP: 261
Packets dropped due to STP non-forwarding state: 321
Packets dropped due to rate-limit: 143
Packets dropped due to broadcast-suppression: 301
Packets dropped due to unicast-suppression: 215
Packets dropped due to multicast-suppression: 241
Packets dropped due to Tx packet aging: 246
# Display the summary of dropped packets on all interfaces.
<Sysname> display packet-drop summary
All interfaces:
Packets dropped due to full GBP or insufficient bandwidth: 301
Packets dropped due to FFP: 261
Packets dropped due to STP non-forwarding state: 321
Packets dropped due to rate-limit: 143
Packets dropped due to broadcast-suppression: 301
Packets dropped due to unicast-suppression: 215
Packets dropped due to multicast-suppression: 241
Packets dropped due to Tx packet aging: 246
Table 6 Command output
|
Field |
Description |
|
Packets dropped due to full GBP or insufficient bandwidth |
Packets that are dropped because the buffer is used up or the bandwidth is insufficient. |
|
Packets dropped due to Fast Filter Processor FFP |
Packets that are filtered out. |
|
Packets dropped due to STP non-forwarding state |
Packets that are dropped because STP is in the non-forwarding state. |
|
Packets dropped due to rate-limit |
Packets that are dropped due to the rate limit set on the device. |
|
Packets dropped due to broadcast-suppression |
Packets that are dropped due to broadcast suppression. |
|
Packets dropped due to unicast-suppression |
Packets that are dropped due to unknown unicast suppression. |
|
Packets dropped due to multicast-suppression |
Packets that are dropped due to multicast suppression. |
|
Packets dropped due to Tx packet aging |
Outbound packets that are timed out. |
duplex
Use duplex to set the duplex mode for an Ethernet interface.
Use undo duplex to restore the default duplex mode of the Ethernet interface.
Syntax
duplex { auto | full | half }
undo duplex
Default
A 10-GE interface operates in full duplex mode, and all other types of Ethernet interfaces operate in autonegotiation mode.
Views
Ethernet interface view
Predefined user roles
network-admin
mdc-admin
Parameters
auto: Configures the interface to autonegotiate the duplex mode with the peer.
full: Configures the interface to operate in full duplex mode, so that the interface can receive and transmit packets at the same time.
half: Configures the interface to operate in half duplex mode, so that the interface can only receive or only transmit packets at one time. Fiber ports do not support the keyword.
Examples
# Configure interface GigabitEthernet 3/0/1 to operate in full duplex mode.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] duplex full
flag sdh
Use flag sdh to set the value for the overhead byte J0 or J1 in SDH frames when the 10-GE interface operates in WAN mode.
Use undo flag sdh to restore the default value of the J0 or J1 byte.
Syntax
flag { j0 | j1 } sdh value
undo flag { j0 | j1 } sdh
Default
The J0 and J1 bytes are padded with 0s.
Views
Ten-GigabitEthernet interface view
Predefined user roles
network-admin
mdc-admin
Parameters
j0: Specifies the Path Trace byte in the Regenerator Section Overhead.
j1: Specifies the Path Trace byte in the High-Order Path Overhead.
value: Specifies the value for the J0 or J1 byte, a string of 1 to 15 characters.
Usage guidelines
This command is effective only when the 10-GE interface is operating in WAN mode.
Examples
# Set the value of the J0 byte in SDH frames to Sysname on interface Ten-GigabitEthernet 3/0/1.
<Sysname> system-view
[Sysname] interface ten-gigabitethernet 3/0/1
[Sysname-Ten-GigabitEthernet3/0/1] port-mode wan
[Sysname-Ten-GigabitEthernet3/0/1] flag j0 sdh Sysname
Related commands
port-mode
flow-control
Use flow-control to enable TxRx mode generic flow control on an Ethernet interface.
Use undo flow-control to disable generic flow control on the Ethernet interface.
Syntax
flow-control
undo flow-control
Default
Generic flow control is disabled on an Ethernet interface.
Views
Ethernet interface view
Predefined user roles
network-admin
mdc-admin
Usage guidelines
To implement flow control on a link, enable the generic flow control function at both ends of the link.
TxRx mode generic flow control enables an Ethernet interface to receive common pause frames from its peer, and send common pause frames to notify its peer of congestions.
With the flow-control command configured, an interface can both send and receive flow control frames:
· When congested, the interface sends a flow control frame to its peer.
· Upon receiving a flow control frame from the peer, the interface suspends sending packets.
Examples
# Enable TxRx mode generic flow control on the interface GigabitEthernet 3/0/1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] flow-control
flow-interval
Use flow-interval to set the interface statistics polling interval.
Use undo flow-interval to restore the default interval.
Syntax
flow-interval interval
undo flow-interval
Default
The interface statistics polling interval is 300 seconds.
Views
Ethernet interface view
Predefined user roles
network-admin
mdc-admin
Parameters
interval: Sets the statistics polling interval, in seconds. The interval is in the range of 5 to 300 and must be a multiple of 5.
Examples
# Set the statistics polling interval to 100 seconds on GigabitEthernet 3/0/1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] flow-interval 100
interface
Use interface to enter interface or subinterface view. With the interface-number.subnumber argument specified, if the subinterface identified by the argument does not exist, this command creates the subinterface first, and then enters subinterface view.
Syntax
interface interface-type { interface-number | interface-number.subnumber }
Views
System view
Predefined user roles
network-admin
mdc-admin
Parameters
interface-type: Specifies an interface type.
interface-number: Specifies an interface number.
interface-number.subnumber: Specifies a subinterface number, where interface-number is a main interface (which must be a Layer 3 Ethernet interface) number, and subnumber is the number of a subinterface created under the interface. The value range for the subnumber argument is 1 to 4094.
Examples
# Enter GigabitEthernet 3/0/1 interface view.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1]
# Create Ethernet subinterface GigabitEthernet 3/0/1.1 and enter GigabitEthernet 3/0/1.1 subinterface view.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1.1
[Sysname-GigabitEthernet3/0/1.1]
jumboframe enable
Use jumboframe enable to allow jumbo frames within the specified length to pass through.
Use undo jumboframe enable to prevent jumbo frames from passing through.
Syntax
jumboframe enable [ value ]
undo jumboframe enable
Default
The device allows jumbo frames within 9216 bytes to pass through.
Views
Layer 2 Ethernet interface view, Layer 3 Ethernet interface view
Predefined user roles
network-admin
mdc-admin
Parameters
value: Sets the maximum length of Ethernet frames that are allowed to pass through. The value range for the argument is 1552 to 9216. On LST1XP16LEB1 and LST1XP16LEC1 cards, the value range for the argument is 1552 to 8168.
Usage guidelines
If you set the value argument multiple times, the most recent configuration takes effect.
Examples
# Enable jumbo frames to pass through GigabitEthernet 3/0/1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] jumboframe enable
link-delay
Use link-delay to set the physical state change suppression interval on an Ethernet interface.
Use undo link-delay to restore the default.
Syntax
link-delay delay-time [ mode { up | updown } ]
undo link-delay
Default
The physical state change suppression interval is one second.
Views
Ethernet interface view
Predefined user roles
network-admin
mdc-admin
Parameters
delay-time: Sets the physical state change suppression interval (in seconds) on the Ethernet interface. The value range for the argument is 0 to 30, however, only 0 to 10 is supported. A value of 0 indicates that physical state changes are not suppressed.
mode up: Suppresses the link-up events. The keyword is not supported in the current software version. The keyword is reserved for future support.
mode updown: Suppresses both the link-up and link-down events.
Usage guidelines
With the link-delay delay-time command configured:
· When the interface comes down, the link-down event is not reported to the CPU unless the interface is still down when the suppression interval (delay-time) expires.
· When the interface goes up, the link-up event is immediately reported.
With the link-delay delay-time mode up command configured:
· When the interface goes up, the link-up event is not reported to the CPU unless the interface is still up when the suppression interval (delay-time) expires.
· When the interface comes down, the link-down event is immediately reported.
With the link-delay delay-time mode updown command configured, when the interface comes down or goes up, the link-down or link-up event is not reported to the CPU unless the interface is still down or up when the suppression interval (delay-time) expires.
On a port, if you configure the link-delay command multiple times, the most recent configuration takes effect.
Do not configure this command on a port with MSTP enabled.
The link-delay delay-time command and the link-delay delay-time mode up command are not supported.
Examples
# Set the physical state change suppression interval to 8 seconds on interface GigabitEthernet 3/0/1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] link-delay 8
loopback
Use loopback to perform a loopback test on an Ethernet interface.
Use undo loopback to cancel a loopback test on an Ethernet interface.
Syntax
loopback { external | internal }
undo loopback
Default
Loopback test is disabled on an interface.
Views
Ethernet interface view
Predefined user roles
network-admin
mdc-admin
Parameters
external: Performs an external loopback test on the Ethernet interface. The keyword is not supported in the current software version. The keyword is reserved for future support.
internal: Performs an internal loopback test on the Ethernet interface.
Usage guidelines
If an Ethernet interface does not work normally, you can perform a loopback test on it to identify the problem.
An Ethernet interface in a loopback test does not forward data traffic.
On a physically down interface (displayed as in DOWN state), you can only perform an internal loopback test, and an external loopback test will fail. On an administratively shut down interface (displayed as in ADM or Administratively DOWN state), you cannot perform an internal or external loopback test.
The speed, duplex, mdi, and shutdown commands are not available during a loopback test.
During a loopback test, the Ethernet interface operates in full duplex mode. When the loopback test is complete, the port returns to its duplex setting.
Examples
# Perform an internal loopback test on GigabitEthernet 3/0/1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] loopback internal
port link-mode
Use port link-mode to change the link mode of an Ethernet interface.
Use undo port link-mode to restore the default.
Syntax
port link-mode { bridge | route }
undo port link-mode
Default
An Ethernet interface operates in Layer 2 mode.
Views
Ethernet interface view
Predefined user roles
network-admin
mdc-admin
Parameters
bridge: Specifies the Layer 2 mode.
route: Specifies the Layer 3 mode.
Usage guidelines
Depending on the layers where the device processes packets received on interfaces, Ethernet interfaces can operate as Layer 2 Ethernet interfaces (in bridge mode) or as Layer 3 Ethernet interfaces (in route mode).
After you change the link mode of an Ethernet interface, all the settings (except the shutdown status) of the Ethernet interface are restored to their defaults under the new link mode. For more information about shutting down or bringing up an interface, see "shutdown."
The command is available on only switches operating in non-standard mode. By default, a switch operates in standard mode. For more information about the system operating modes, see Fundamentals Configuration Guide.
The following Ethernet interfaces do not support switching the operating mode: aggregation group member ports, reflector port of a remote source mirroring group, and Ethernet interfaces of a switch operating in IRF mode and with enhanced IRF enabled. For more information about reflector ports, see Network Management and Monitoring Configuration Guide. For more information about enhanced IRF, see IRF Configuration Guide.
Examples
# Configure GigabitEthernet 3/0/1 to operate in Layer 3 mode.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] port link-mode route
port-mode
Use port-mode to configure a 10-GE interface to operate in LAN or WAN mode.
Use undo port-mode to restore the default.
Syntax
port-mode { lan | wan }
undo port-mode
Default
A 10-GE interface operates in LAN mode.
Views
Ten-GigabitEthernet interface view
Predefined user roles
network-admin
mdc-admin
Parameters
lan: Configures the interface to operate in LAN mode. A port operating in this mode transmits Ethernet packets and connects an Ethernet network.
wan: Configures the interface to operate in WAN mode. A port operating in this mode transmits SDH packets and connects an SDH network. In addition, it supports point-to-point links only.
Examples
# Configure the interface Ten-GigabitEthernet 3/0/1 to operate in WAN mode.
<Sysname> system-view
[Sysname] interface ten-gigabitethernet3/0/1
[Sysname-Ten-GigabitEthernet3/0/1] port-mode wan
reset counters interface
Use reset counters interface to clear the Ethernet interface or subinterface statistics.
Syntax
reset counters interface [ interface-type [ interface-number | interface-number.subnumber ] ]
Views
User view
Predefined user roles
network-admin
mdc-admin
Parameters
interface-type: Specifies an interface type.
interface-number: Specifies an interface number.
interface-number.subnumber: Specifies a subinterface number, where interface-number is a main interface (which must be a Layer 3 Ethernet interface) number; subnumber is the number of a subinterface created under the interface. The value range for the subnumber argument is 1 to 4094.
Usage guidelines
Before collecting traffic statistics for a specific period of time on an interface, clear the old statistics first.
If no interface type is specified, this command clears statistics for all interfaces.
If only the interface type is specified, this command clears statistics for all interfaces of that type.
If both the interface type and the interface or subinterface number are specified, this command clears statistics for the specified interface or subinterface.
Examples
# Clear the statistics of GigabitEthernet 3/0/1.
<Sysname> reset counters interface GigabitEthernet 3/0/1
Related commands
· display interface
· display counters interface
· display counters rate interface
reset packet-drop interface
Use reset packet-drop interface to clear the dropped packet statistics on an interface or multiple interfaces.
Syntax
reset packet-drop interface [ interface-type [ interface-number ] ]
Views
User view
Predefined user roles
network-admin
mdc-admin
Parameters
interface-type: Specify an interface type. If you do not specify an interface type, this command clears dropped packet statistics on all the interfaces on the device.
interface-number: Specify an interface number. If you do not specify this argument, this command clears dropped packet statistics on all interfaces of the specified type.
Examples
# Clear dropped packet statistics on GigabitEthernet 3/0/1.
<Sysname> reset packet-drop interface GigabitEthernet 3/0/1
# Clear dropped packet statistics on all interfaces.
<Sysname> reset packet-drop interface
Related commands
display packet-drop
shutdown
Use shutdown to shut down an Ethernet interface or subinterface.
Use undo shutdown to bring up an Ethernet interface or subinterface.
Syntax
shutdown
undo shutdown
Default
Ethernet interfaces are down, and Ethernet subinterfaces are up.
Views
Ethernet interface view, Ethernet subinterface view
Predefined user roles
network-admin
mdc-admin
Usage guidelines
You might need to shut down and then bring up an Ethernet interface to make some interface configurations take effect.
Examples
# Shut down and then bring up GigabitEthernet 3/0/1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] shutdown
[Sysname-GigabitEthernet3/0/1] undo shutdown
# Shut down and then bring up Layer 3 Ethernet subinterface GigabitEthernet 3/0/1.1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1.1
[Sysname-GigabitEthernet3/0/1.1] shutdown
[Sysname-GigabitEthernet3/0/1.1] undo shutdown
speed
Use speed to set the speed of an Ethernet interface.
Use undo speed to restore the default.
Syntax
speed { 10 | 100 | 1000 | 10000 | auto }
undo speed
Default
The speed of an Ethernet interface is autonegotiated.
Views
Ethernet interface view
Predefined user roles
network-admin
mdc-admin
Parameters
10: Sets the interface speed to 10 Mbps.
100: Sets the interface speed to 100 Mbps.
1000: Sets the interface speed to 1000 Mbps.
10000: Sets the interface speed to 10000 Mbps.
auto: Enables the interface to negotiate a speed with its peer.
Usage guidelines
For an Ethernet copper port, use the speed command to set its speed to match the speed of the peer interface.
For a fiber port, use the speed command to set its speed to match the rate of a transceiver module.
A fiber port does not support the 10 and 100 keyword of the command.
A 10-GE interface does not support the command.
Examples
# Configure GigabitEthernet 3/0/1 to autonegotiate the speed.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] speed auto
Layer 2 Ethernet interface/subinterface commands
broadcast-suppression
Use broadcast-suppression to enable broadcast suppression and set the broadcast suppression threshold.
Use undo broadcast-suppression to restore the default.
Syntax
broadcast-suppression { ratio | pps max-pps | kbps max-kbps }
undo broadcast-suppression
Default
Ethernet interfaces do not suppress broadcast traffic.
Views
Layer 2 Ethernet interface view
Predefined user roles
network-admin
mdc-admin
Parameters
ratio: Sets the broadcast suppression threshold as a percentage of the maximum interface rate. The value range for the argument is 0 to 100. The smaller the percentage, the less broadcast traffic is allowed to pass through. The argument is always 100. As a result, you cannot suppression broadcast traffic by using the argument.
pps max-pps: Specifies the maximum number of broadcast packets that the interface can forward per second. The value range for the max-pps argument (in pps) is 1 to 1.4881 × the maximum interface rate. For example, the value range for the argument is 1 to 1488100 on a GE interface.
kbps max-kbps: Specifies the maximum number of kilobits of broadcast traffic that the Ethernet interface can forward per second. The value range for the argument (in kbps) is 1 to the maximum interface rate.
Usage guidelines
You can use the broadcast storm suppression function to limit the size of broadcast traffic on an interface. When the broadcast traffic on the interface exceeds this threshold, the system drops packets until the traffic drops below this threshold.
When you configure the suppression threshold in pps or kbps, the device converts the configured value into a multiple of a certain step (6400 for pps and 50 for kbps) supported by the chip. As a result, the actual suppression threshold may be different from the configured one. To determine the suppression threshold that takes effect, see the prompts on the device.
Examples
# Set the broadcast suppression threshold to 10000 kbps on GigabitEthernet 3/0/1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] broadcast-suppression kbps 10000
Related commands
· multicast-suppression
· unicast-suppression
mdix-mode
|
|
IMPORTANT: Fiber ports do not support this command. |
Use mdix-mode to configure the Medium Dependent Interface Cross-Over (MDIX) mode of an Ethernet interface.
Use undo mdix-mode to restore the default.
Syntax
mdix-mode { automidx | mdi| mdix }
undo mdix-mode
Default
Ethernet interfaces operate in automdix mode.
Views
Layer 2 Ethernet interface view
Predefined user roles
network-admin
mdc-admin
Parameters
automidx: Specifies that the interface negotiates pin roles with its peer.
mdi: Specifies that pins 1 and 2 are transmit pins and pins 3 and 6 are receive pins.
mdix: Specifies that pins 1 and 2 are receive pins and pins 3 and 6 are transmit pins.
Examples
# Set GigabitEthernet 3/0/1 to operate in MDI mode.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] mdix-mode mdi
multicast-suppression
Use multicast-suppression to enable multicast storm suppression and set the multicast storm suppression threshold.
Use undo multicast-suppression to restore the default.
Syntax
multicast-suppression { ratio | pps max-pps | kbps max-kbps }
undo multicast-suppression
Default
Ethernet interfaces do not suppress multicast traffic.
Views
Layer 2 Ethernet interface view, Layer 2 Ethernet subinterface view
Predefined user roles
network-admin
mdc-admin
Parameters
ratio: Sets the multicast suppression threshold as a percentage of the maximum interface rate. The value range for the argument (in percentage) is 0 to 100. The smaller the percentage, the less multicast traffic is allowed to pass through. The argument is always 100. As a result, you cannot suppression multicast traffic by using the argument.
pps max-pps: Specifies the maximum number of multicast packets that the interface can forward per second. The value range for the max-pps argument (in pps) is 1 to 1.4881 × the maximum interface rate. For example, the value range for the argument is 1 to 1488100 on a GE interface.
kbps max-kbps: Specifies the maximum number of kilobits of multicast traffic that the Ethernet interface can forward per second. The value range for the argument (in kbps) is 1 to the maximum interface rate.
Usage guidelines
You can use the multicast storm suppression function to limit the size of multicast traffic on an interface. When the multicast traffic on the interface exceeds this threshold, the system drops packets until the traffic drops below this threshold.
When you configure the suppression threshold in pps or kbps, the device converts the configured value into a multiple of a certain step (6400 for pps and 50 for kbps) supported by the chip. As a result, the actual suppression threshold may be different from the configured one. To determine the suppression threshold that takes effect, see the prompts on the device.
Examples
# Set the multicast storm suppression threshold to 10000 kbps on GigabitEthernet 3/0/1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] multicast-suppression kbps 10000
Related commands
· broadcast-suppression
· unicast-suppression
port up-mode
Use port up-mode to forcibly bring up a fiber GE or 10-GE port.
Use undo port up-mode to restore the default.
Syntax
port up-mode
undo port up-mode
Views
Ethernet interface view
Predefined user roles
network-admin
mdc-admin
Usage guidelines
You can use this command to forcibly bring up a fiber Ethernet port, and enable the port to forward packets unidirectionally over a single link. In this way, transmission links are well utilized.
After you forcibly bring up an Ethernet fiber port, the fiber port stays physically up regardless of whether or not an optical module or fiber connections are present for the port.
Only 10-GE fiber ports operating in LAN mode and GE fiber ports support this command. Copper ports and combo interfaces do not support this command.
To configure this command on a port, make sure the port is operating in bridge mode.
The port up-mode command is mutually exclusive with any of the shutdown, speed, duplex, and loopback commands.
The fiber port cannot properly forward traffic if you install a transceiver module, 100/1000-Mbps transceiver module, or 100-Mbps transceiver module into the port and configure the port up-mode command. To solve the problem, use the undo port up-mode command on the fiber port.
Examples
# Forcibly bring up the fiber port GigabitEthernet 3/0/1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] port up-mode
unicast-suppression
Use unicast-suppression to enable unicast storm suppression and set the unicast storm suppression threshold.
Use undo unicast-suppression to restore the default.
Syntax
unicast-suppression { ratio | pps max-pps | kbps max-kbps }
undo unicast-suppression
Default
Ethernet interfaces do not suppress unicast traffic.
Views
Layer 2 Ethernet interface view
Predefined user roles
network-admin
mdc-admin
Parameters
ratio: Sets the unicast suppression threshold as a percentage of the maximum interface rate. The value range for the argument (in percentage) is 0 to 100. The smaller the percentage, the less unicast traffic is allowed to pass through. The argument is always 100. As a result, you cannot suppression unicast traffic by using the argument.
pps max-pps: Specifies the maximum number of unicast packets that the interface can forward per second. The value range for the max-pps argument (in pps) is 1 to 1.4881 × the maximum interface rate. For example, the value range for the argument is 1 to 1488100 on a GE interface.
kbps max-kbps: Specifies the maximum number of kilobits of unicast traffic that the Ethernet interface can forward per second. The value range for the argument (in kbps) is 1 to the maximum interface rate.
Usage guidelines
You can use the unicast storm suppression function to limit the size of unicast traffic on an interface. When the unicast traffic on the interface exceeds this threshold, the system discards packets until the unicast traffic drops below this threshold.
When you configure the suppression threshold in pps or kbps, the device converts the configured value into a multiple of a certain step (6400 for pps and 50 for kbps) supported by the chip. As a result, the actual suppression threshold may be different from the configured one. To determine the suppression threshold that takes effect, see the prompts on the device.
Examples
# Set the unicast storm suppression threshold to 10000 kbps on GigabitEthernet 3/0/1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] unicast-suppression kbps 10000
Related commands
· broadcast-suppression
· multicast-suppression
Layer 3 Ethernet interface or subinterface commands
mtu
Use mtu to set the MTU for an Ethernet interface or subinterface.
Use undo mtu to restore the default.
Syntax
mtu size
undo mtu
Default
The MTU of an Ethernet interface or subinterface is 1500 bytes.
Views
Layer 3 Ethernet interface view, Layer 3 Ethernet subinterface view
Predefined user roles
network-admin
mdc-admin
Parameters
size: Sets the maximum transmission unit (MTU) in bytes, which is in the range of 64 to 9198.
Usage guidelines
Do not modify the MTU in general cases.
Examples
# Set the MTU to 1430 bytes for Layer 3 Ethernet interface GigabitEthernet 3/0/1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1
[Sysname-GigabitEthernet3/0/1] mtu 1430
# Set the MTU to 1400 bytes for Layer 3 Ethernet subinterface GigabitEthernet 3/0/1.1.
<Sysname> system-view
[Sysname] interface GigabitEthernet 3/0/1.1
[Sysname-GigabitEthernet3/0/1.1] mtu 1430
