Login
- Table of Contents
- Related Documents
-
| Title | Size | Download |
|---|---|---|
| 01-Hardware Information and Specifications | 1.89 MB |
1 Product models and technical specifications
3 Removable components and compatibility matrixes
450W power supplies (PSR450-12A and PSR450-12A1)
450W DC power supply (PSR450-12D)
Removable fan trays available for the S6526XE-HI switch series
Removable fan trays available for the S6526XE-EI switch series
10G/5G/2.5G/1G autosensing Ethernet port
Ports on an LSPM6FWD firewall module
Fan tray status LED on a fan tray
LEDs on an LSPM6FWD firewall module
1 Product models and technical specifications
Unless otherwise stated, interface modules and interface cards are used interchangeably in this document.
Product models
Table1-1 Switch series and models
|
Model |
Product code (PID) |
|
|
S6526XE-HI switch series |
S6526XE-32X6CC-HI |
LS-6526XE-32X6CC-HI |
|
S6526XE-48X6CC-HI |
LS-6526XE-48X6CC-HI |
|
|
S6526XE-EI switch series |
S6526XE-32X4CC-EI |
LS-6526XE-32X4CC-EI |
|
S6526XE-48X4CC-EI |
LS-6526XE-48X4CC-EI |
|
|
NOTE: · To obtain the purchase information, see the product data sheet at https://www.h3c.com/en/Products_and_Solutions/InterConnect/Switches/ and pay attention to the switch product lifecycle management announcement at https://www.h3c.com/en/Support/Policy_Dynamics/Management_Strategy/Products_End_of_Life_Announcement/Switches/. · For information about product and software compatibility, see the release notes. |
Technical specifications
S6526XE-HI switch series
Table1-2 Technical specifications
|
Item |
S6526XE-32X6CC-HI |
S6526XE-48X6CC-HI |
|
Physical specifications |
||
|
Dimensions (H × W × D) |
44 × 440 × 400 mm (1.73 × 17.32 × 15.75 in) |
|
|
Dimensions (H × W × D, with package materials) |
150 × 556 × 528 mm (5.91 × 21.89 × 20.79 in) |
|
|
Weight (fully configured with power supplies, fan trays, and expansion cards) |
≤ 7.9 kg (17.42 lb) |
≤ 8.1 kg (17.86 lb) |
|
Technical specifications |
||
|
Memory (RAM) |
4 GB |
|
|
Flash |
4 GB |
|
|
Port types and quantity |
||
|
Console port |
· 1 × Type-C USB console port · 1 × serial console port Only the Type-C USB console port is available when you connect both ports. |
|
|
USB port |
1 |
|
|
Management Ethernet port |
1 |
|
|
SFP+ port |
32 |
48 |
|
QSFP28 port |
6 |
|
|
IRF physical port |
The following ports support IRF connection: · SFP+ ports and QSFP28 ports on the front panel · Ports that can be provided by the expansion card on the rear panel: ¡ SFP+ ports ¡ SFP28 ports ¡ QSFP+ ports ¡ QSFP28 ports |
|
|
Fan tray, power supply, and expansion card slots |
||
|
Expansion slot |
1 |
|
|
Power supply slot |
2 |
|
|
Fan tray slot |
4 |
|
|
Power supply specifications |
||
|
Power input |
AC input, DC input Note: For DC input, you can use a –48 VDC power source in the equipment room or an RPS (H3C RPS1600-A). |
|
|
Power specifications |
See "Removable power supplies" |
|
|
Power consumption |
||
|
Power consumption (static) Data collection standard: no load |
Single AC input: 89 W Dual AC inputs: 90 W Single DC input: 86 W Dual DC inputs: 98 W |
Single AC input: 85 W Dual AC inputs: 89 W Single DC input: 83 W Dual DC inputs: 96 W |
|
Power consumption (typical) Data collection standard: fully configured with copper cables or network cables, at 30% load |
Single AC input: 117 W Dual AC inputs: 125 W Single DC input: 123 W Dual DC inputs: 126 W |
Single AC input: 118 W Dual AC inputs: 129 W Single DC input: 124 W Dual DC inputs: 131 W |
|
Power consumption (full load) Data collection standard: fully configured with transceiver modules or network cables, at 100% load |
Single AC input: 237 W Dual AC inputs: 242 W Single DC input: 249 W Dual DC inputs: 256 W |
Single AC input: 251 W Dual AC inputs: 255 W Single DC input: 262 W Dual DC inputs: 265 W |
|
Thermal consumption |
||
|
Thermal consumption (static) Data collection standard: no load |
Single AC input: 304 BTU/h Dual AC inputs: 307 BTU/h Single DC input: 294 BTU/h Dual DC inputs: 335 BTU/h |
Single AC input: 290 BTU/h Dual AC inputs: 304 BTU/h Single DC input: 284 BTU/h Dual DC inputs: 328 BTU/h |
|
Thermal consumption (typical) Data collection standard: fully configured with copper cables or network cables, at 30% load |
Single AC input: 399 BTU/h Dual AC inputs: 427 BTU/h Single DC input: 420 BTU/h Dual DC inputs: 430 BTU/h |
Single AC input: 403 BTU/h Dual AC inputs: 440 BTU/h Single DC input: 423 BTU/h Dual DC inputs: 447 BTU/h |
|
Thermal consumption (full load) Data collection standard: fully configured with transceiver modules or network cables, at 100% load |
Single AC input: 809 BTU/h Dual AC inputs: 826 BTU/h Single DC input: 850 BTU/h Dual DC inputs: 872 BTU/h |
Single AC input: 856 BTU/h Dual AC inputs: 870 BTU/h Single DC input: 894 BTU/h Dual DC inputs: 904 BTU/h |
|
Heat dissipation |
||
|
Heat dissipation method |
Air cooling |
|
|
Ventilation aisle |
Front-to-rear or rear-to-front airflow, determined by the selected fan tray model |
|
|
Reliability and availability |
||
|
Power supply redundancy |
1+1 |
|
|
Fan tray redundancy |
You must fully configure the switch with fan trays. |
|
|
Hot swapping |
Power supplies and fan trays support hot swapping. Expansion cards (except for the LSWM2XMGT4PM and LSWM2SP8PM) support hot swapping. Do not hot swap an expansion card when the switch is starting up. |
|
|
Mean Time Between Failure (MTBF) (year) |
116.18 |
110.03 |
|
Mean Time To Repair (MTTR) (hour) |
1 |
1 |
|
Availability |
99.99990% |
99.99990% |
|
Environment specifications |
||
|
Sound pressure level at 27°C (80.6°F) |
53.0 dBA |
53.0 dBA |
|
Altitude |
–60 m to +5000 m (–196.85 ft to +16404.20 ft) |
|
|
Operating temperature |
–5°C to +45°C (23°F to 113°F) Note: The allowed maximum temperature decreases by 0.33 °C (32.59°F) as the altitude increases by 100 m (328.08 ft) from 0 m (0 ft). |
|
|
Storage temperature |
–40°C to +70°C (–40°F to +158°F) |
|
|
Relative humidity |
5% RH to 95% RH, noncondensing |
|
|
Compliance |
||
|
Product compliance |
· Safety standards · EMC standards · Environmental and eco-friendly standards |
|
S6526XE-EI switch series
Table1-3 Technical specifications
|
Item |
S6526XE-32X4CC-EI |
S6526XE-48X4CC-EI |
|
Physical specifications |
||
|
Dimensions (H × W × D) |
44 × 440 × 400 mm (1.73 × 17.32 × 15.75 in) |
|
|
Dimensions (H × W × D, with package materials) |
150 × 556 × 528 mm (5.91 × 21.89 × 20.79 in) |
|
|
Weight (fully configured with power supplies, fan trays, and expansion cards) |
≤ 8.1 kg (17.86 lb) |
≤ 8.2 kg (18.08 lb) |
|
Technical specifications |
||
|
Memory (RAM) |
4 GB |
|
|
Flash |
4 GB |
|
|
Port types and quantity |
||
|
Console port |
· 1 × Type-C USB console port · 1 × serial console port Only the Type-C USB console port is available when you connect both ports. |
|
|
USB port |
1 |
|
|
Management Ethernet port |
1 |
|
|
SFP+ port |
32 |
48 |
|
QSFP28 port |
4 |
|
|
IRF physical port |
The following ports support IRF connection: · SFP+ ports and QSFP28 ports on the front panel · Ports that can be provided by the expansion card on the rear panel: ¡ SFP+ ports ¡ SFP28 ports ¡ QSFP+ ports ¡ QSFP28 ports |
|
|
Fan tray, power supply, and expansion card slots |
||
|
Expansion slot |
2 |
|
|
Power supply slot |
2 |
|
|
Fan tray slot |
2 |
|
|
Power supply specifications |
||
|
Power input |
AC input, DC input Note: For DC input, you can use a –48 VDC power source in the equipment room or an RPS (H3C RPS1600-A). |
|
|
Power specifications |
See "Removable power supplies" |
|
|
Power consumption |
||
|
Power consumption (static) Data collection standard: no load |
Single AC input: 75 W Dual AC inputs: 83 W Single DC input: 74 W Dual DC inputs: 82 W |
Single AC input: 72 W Dual AC inputs: 82 W Single DC input: 72 W Dual DC inputs: 81 W |
|
Power consumption (typical) Data collection standard: fully configured with copper cables or network cables, at 30% load |
Single AC input: 91 W Dual AC inputs: 98 W Single DC input: 94 W Dual DC inputs: 101 W |
Single AC input: 100 W Dual AC inputs: 108 W Single DC input: 103 W Dual DC inputs: 112 W |
|
Power consumption (full load) Data collection standard: fully configured with transceiver modules or network cables, at 100% load |
Single AC input: 239 W Dual AC inputs: 243 W Single DC input: 249 W Dual DC inputs: 250 W |
Single AC input: 275 W Dual AC inputs: 277 W Single DC input: 279 W Dual DC inputs: 283 W |
|
Thermal consumption |
||
|
Thermal consumption (static) Data collection standard: no load |
Single AC input: 256 TU/h Dual AC inputs: 284 TU/h Single DC input: 253 TU/h Dual DC inputs: 280 TU/h |
Single AC input: 246 TU/h Dual AC inputs: 280 TU/h Single DC input: 246 TU/h Dual DC inputs: 277 TU/h |
|
Thermal consumption (typical) Data collection standard: fully configured with copper cables or network cables, at 30% load |
Single AC input: 316 TU/h Dual AC inputs: 311 TU/h Single DC input: 321 TU/h Dual DC inputs: 345 TU/h |
Single AC input: 341 TU/h Dual AC inputs: 367 TU/h Single DC input: 352 TU/h Dual DC inputs: 382 TU/h |
|
Thermal consumption (full load) Data collection standard: fully configured with transceiver modules or network cables, at 100% load |
Single AC input: 815 TU/h Dual AC inputs: 829 TU/h Single DC input: 850 TU/h Dual DC inputs: 853 TU/h |
Single AC input: 938 TU/h Dual AC inputs: 945 TU/h Single DC input: 952 TU/h Dual DC inputs: 966 TU/h |
|
Heat dissipation |
||
|
Heat dissipation method |
Air cooling |
|
|
Ventilation aisle |
Front-to-rear or rear-to-front airflow, determined by the selected fan tray model |
|
|
Reliability and availability |
||
|
Power supply redundancy |
1+1 |
|
|
Fan tray redundancy |
You must fully configure the switch with fan trays. |
|
|
Hot swapping |
Power supplies and fan trays support hot swapping. Expansion cards (except for the LSWM2XMGT4PM and LSWM2SP8PM) support hot swapping. Do not hot swap an expansion card when the switch is starting up. |
|
|
Mean Time Between Failure (MTBF) (year) |
41.02 |
39.98 |
|
Mean Time To Repair (MTTR) (hour) |
1 |
1 |
|
Availability |
99.99971% |
99.99972% |
|
Environment specifications |
||
|
Sound pressure level at 27°C (80.6°F) |
48.5 dBA |
|
|
Altitude |
–60 m to +5000 m (–196.85 ft to +16404.20 ft) |
|
|
Operating temperature |
–5°C to +45°C (23°F to 113°F) Note: The allowed maximum temperature decreases by 0.33 °C (32.59°F) as the altitude increases by 100 m (328.08 ft) from 0 m (0 ft). |
|
|
Storage temperature |
–40°C to +70°C (–40°F to +158°F) |
|
|
Relative humidity |
5% RH to 95% RH, noncondensing |
|
|
Compliance |
||
|
Product compliance |
· Safety standards · EMC standards · Environmental and eco-friendly standards |
|
2 Chassis views
S6526XE-HI switch series
S6526XE-32X6CC-HI
Figure2-1 Front panel
|
(1) SFP+ port |
(2) SFP+ port LED |
|
(3) QSFP28 port |
(4) QSFP28 port LED |
|
(5) Type-C USB console port |
(6) System status LED (SYS) |
|
(7) Expansion card status LED (SLOT) |
|
|
|
NOTE: The Type-C USB console port is used for device management only, and cannot be used for storage. |
|
(1) Management Ethernet port LED (ACT) |
(2) Management Ethernet port (MGMT) |
|
(3) Management Ethernet port LED (LINK) |
(4) Reset button (RESET) |
|
(5) Serial console port |
(6) Expansion card |
|
(7) Fan tray 1 |
(8) Fan tray 2 |
|
(9) Fan tray 3 |
(10) Fan tray 4 |
|
(11) Power supply 1 |
(12) Power supply 2 |
|
(13) USB port |
(14) Serial label pull tab |
|
(15) Grounding screw |
|
The S6526XE-32X6CC-HI switch came with power supply slot 1 empty and power supply slot 2 installed with a filler panel. You can install one or two power supplies for the switch as required. In Figure2-2, two PSR450-12A1 AC power supplies are installed in the power supply slots.
The S6526XE-32X6CC-HI switch came with four fan tray slots empty. You must install four fan trays of the same model for the switch. In Figure2-2, four LSPM1FANSB-SN fan trays are installed in the fan tray slots.
The S6526XE-32X6CC-HI switch came with the expansion slot installed with a filler panel. You can select an expansion card for the switch as required. In Figure2-2, an LSWM2SP8P interface card is installed in the expansion slot.
The S6526XE-32X6CC-HI switch supports shipping with fan trays and power supplies installed. For the switch to be shipped with fan trays or power supplies installed, contact the marketing staff.
The S6526XE-32X6CC-HI switch has a reset button on the rear panel. The system LED flashes when the reset button is being pressed. To reboot the switch, press and hold the button for 1 to 5 seconds. To restore the switch to the factory defaults and reboot it, press and hold the reset button for more than 5 seconds.
S6526XE-48X6CC-HI
Figure2-3 Front panel
|
(1) SFP+ port |
(2) SFP+ port LED |
|
(3) QSFP28 port |
(4) QSFP28 port LED |
|
(5) Type-C USB console port |
(6) System status LED (SYS) |
|
(7) Expansion card status LED (SLOT) |
|
|
|
NOTE: The Type-C USB console port is used for device management only, and cannot be used for storage. |
|
(1) Management Ethernet port LED (ACT) |
(2) Management Ethernet port (MGMT) |
|
(3) Management Ethernet port LED (LINK) |
(4) Reset button (RESET) |
|
(5) Serial console port |
(6) Expansion card |
|
(7) Fan tray 1 |
(8) Fan tray 2 |
|
(9) Fan tray 3 |
(10) Fan tray 4 |
|
(11) Power supply 1 |
(12) Power supply 2 |
|
(13) USB port |
(14) Serial label pull tab |
|
(15) Grounding screw |
|
The S6526XE-48X6CC-HI switch came with power supply slot 1 empty and power supply slot 2 installed with a filler panel. You can install one or two power supplies for the switch as required. In Figure2-4, two PSR450-12A1 AC power supplies are installed in the power supply slots.
The S6526XE-48X6CC-HI switch came with four fan tray slots empty. You must install four fan trays of the same model for the switch. In Figure2-4, four LSPM1FANSB-SN fan trays are installed in the fan tray slots.
The S6526XE-48X6CC-HI switch came with the expansion slot installed with a filler panel. You can select an expansion card for the switch as required. In Figure2-4, an LSWM2SP8P interface card is installed in the expansion slot.
The S6526XE-48X6CC-HI switch supports shipping with fan trays and power supplies installed. For the switch to be shipped with fan trays or power supplies installed, contact the marketing staff.
The S6526XE-48X6CC-HI switch has a reset button on the rear panel. The system LED flashes when the reset button is being pressed. To reboot the switch, press and hold the button for 1 to 5 seconds. To restore the switch to the factory defaults and reboot it, press and hold the reset button for more than 5 seconds.
S6526XE-EI switch series
S6526XE-32X4CC-EI
Figure2-5 Front panel
|
(1) SFP+ port |
(2) SFP+ port LED |
|
(3) QSFP28 port |
(4) QSFP28 port LED |
|
(5) Management Ethernet port (MGMT) |
(6) Management Ethernet port LED (ACT) |
|
(7) Management Ethernet port LED (LINK) |
(8) USB port |
|
(9) Type-C USB console port |
(10) Reset button (RESET) |
|
(11) Serial console port |
(12) System status LED (SYS) |
|
(13) Expansion card status LED 2 (SLOT2) |
(14) Expansion card status LED 1 (SLOT1) |
|
|
NOTE: The Type-C USB console port is used for device management only, and cannot be used for storage. |
|
(1) Grounding screw |
(2) Fan tray 1 |
|
(3) Expansion card 1 |
(4) Expansion card 2 |
|
(5) Fan tray 2 |
(6) Power supply 1 |
|
(7) Power supply 2 |
(8) Serial label pull tab |
The S6526XE-32X4CC-EI switch came with power supply slot 1 empty and power supply slot 2 installed with a filler panel. You can install one or two power supplies for the switch as required. In Figure2-6, two PSR450-12A1 AC power supplies are installed in the power supply slots.
The S6526XE-32X4CC-EI switch came with two fan tray slots empty. You must install two fan trays of the same model for the switch. In Figure2-6, two FAN-40B-1-A fan trays are installed in the fan tray slots.
The S6526XE-32X4CC-EI switch came with two expansion slots each installed with a filler panel. You can select expansion cards for the switch as required. In Figure2-6, two LSWM2SP8P interface cards are installed in the expansion slots.
The S6526XE-32X4CC-EI switch supports shipping with fan trays and power supplies installed. For the switch to be shipped with fan trays or power supplies installed, contact the marketing staff.
The S6526XE-32X4CC-EI switch has a reset button on the rear panel. The system LED flashes when the reset button is being pressed. To reboot the switch, press and hold the button for 1 to 5 seconds. To restore the switch to the factory defaults and reboot it, press and hold the reset button for more than 5 seconds.
S6526XE-48X4CC-EI
Figure2-7 Front panel
|
(1) SFP+ port |
(2) SFP+ port LED |
|
(3) QSFP28 port |
(4) QSFP28 port LED |
|
(5) Management Ethernet port (MGMT) |
(6) Management Ethernet port LED (ACT) |
|
(7) Management Ethernet port LED (LINK) |
(8) USB port |
|
(9) Type-C USB console port |
(10) Reset button (RESET) |
|
(11) Serial console port |
(12) System status LED (SYS) |
|
(13) Expansion card status LED 2 (SLOT2) |
(14) Expansion card status LED 1 (SLOT1) |
|
|
NOTE: The Type-C USB console port is used for device management only, and cannot be used for storage. |
|
(1) Grounding screw |
(2) Fan tray 1 |
|
(3) Expansion card 1 |
(4) Expansion card 2 |
|
(5) Fan tray 2 |
(6) Power supply 1 |
|
(7) Power supply 2 |
(8) Serial label pull tab |
The S6526XE-48X4CC-EI switch came with power supply slot 1 empty and power supply slot 2 installed with a filler panel. You can install one or two power supplies for the switch as required. In Figure2-8, two PSR450-12A1 AC power supplies are installed in the power supply slots.
The S6526XE-48X4CC-EI switch came with two fan tray slots empty. You must install two fan trays of the same model for the switch. In Figure2-8, two FAN-40B-1-A fan trays are installed in the fan tray slots.
The S6526XE-48X4CC-EI switch came with two expansion slots each installed with a filler panel. You can select expansion cards for the switch as required. In Figure2-8, two LSWM2SP8P interface cards are installed in the expansion slots.
The S6526XE-48X4CC-EI switch supports shipping with fan trays and power supplies installed. For the switch to be shipped with fan trays or power supplies installed, contact the marketing staff.
The S6526XE-48X4CC-EI switch has a reset button on the rear panel. The system LED flashes when the reset button is being pressed. To reboot the switch, press and hold the button for 1 to 5 seconds. To restore the switch to the factory defaults and reboot it, press and hold the reset button for more than 5 seconds.
3 Removable components and compatibility matrixes
The switch supports removable components. Table3-1 describes the removable components available for the switch.
Table3-1 Compatibility matrix between switches and removable components
|
FRU model |
S6526XE-32X6CC-HI S6526XE-48X6CC-HI |
S6526XE-32X4CC-EI S6526XE-48X4CC-EI |
|
Removable power supplies |
||
|
PSR450-12D |
Supported |
|
|
PSR450-12A |
Supported |
|
|
PSR450-12A1 |
Supported |
|
|
Removable fan trays |
||
|
LSPM1FANSA-SN |
Supported |
Not supported |
|
LSPM1FANSB-SN |
Supported |
Not supported |
|
FAN-40B-1-A |
Not supported |
Supported |
|
FAN-40F-1-A |
Not supported |
Supported |
|
Expansion cards |
||
|
LSPM6FWD |
Supported |
|
|
LSWM4SP8PM |
Supported |
|
|
LSWM2SP8P |
Supported |
|
|
LSWM2QP2P |
Supported |
|
|
LSWM2ZSP8P |
Supported |
|
|
LSWM2ZQP2P |
Supported |
|
|
LSWM2XMGT4PM |
Supported |
|
The power supplies support asset management. You can use the display device manuinfo command to view the name, sequence number, and vendor of the power supply you have installed on the switch.
You can install one power supply, or two power supplies for 1+1 redundancy on the switch.
The switch uses removable fan trays. Do not power on the switch if it is not fully configured with fan trays of the same model.
To install two expansion cards on an S6526XE-EI switch, make sure one of the two expansion cards is an LSWM2QP2P, LSWM2ZQP2P, or LSPM6FWD.
The expansion cards (except for the LSWM2XMGT4PM and LSWM2SP8PM) support hot swapping. Do not install or remove an expansion card during the startup of the switch.
4 Removable power supplies
450W power supplies (PSR450-12A and PSR450-12A1)
View
Figure4-1 PSR450-12A1 AC power supply view
The views of the PSR450-12A and PSR450-12A1 AC power supplies are similar, with only differences in the latch color and identifier.
LEDs
For information about the status LED, see "Power status LED."
Features
PSR450-12A and PSR450-12A1 are AC power supplies with AC or HVDC input and DC output. Table4-1 describes the features provided by the PSR450-12A and PSR450-12A1 power supplies.
Table4-1 Features provided by the PSR450-12A and PSR450-12A1 power supplies
|
Feature |
Description |
|
Protection function |
Protection against input overcurrent, input undervoltage, output overvoltage, output current limiting, output shortcircuit, and overtemperature conditions. |
|
Support for redundancy |
Two power supplies can be connected in parallel to achieve 1+1 redundancy and load balancing. |
|
Support for hot swapping |
You can remove one of the power supplies in 1+1 redundancy when the switch is operating correctly. |
Technical specifications
Table4-2 Technical specifications
|
Item |
Specification |
|
Dimensions (H × W × D) |
40.2 × 50.5 × 246 mm (1.58 × 1.99 × 9.69 in), including the handle |
|
Weight |
0.7 kg (1.54 lb) |
|
Rated AC input voltage range |
AC input: 100 to 240 VAC @ 50 or 60 Hz HVDC input: 240 VDC |
|
Max AC input voltage range |
AC input: 90 to 290 VAC @ 47 to 63 Hz HVDC input: 180 to 320 VDC |
|
Rated input current |
AC input: 6 A HVDC input: 3 A |
|
Rated output current |
AC input: 37.5 A HVDC input: 2 A |
|
Rated output voltage |
AC input: 12 V HVDC input: 3.3 V |
|
Rated output power |
450 W |
|
Melting current of power supply fuse |
15 A/250 V |
450W DC power supply (PSR450-12D)
View
Figure4-2 PSR450-12D DC power supply view
LEDs
For information about the status LED, see "Power status LED."
Features
PSR450-12D is a DC power supply with DC input and DC output. Table4-3 describes the features provided by the PSR450-12D power supply.
Table4-3 Features provided by the PSR450-12D power supply
|
Feature |
Description |
|
Protection function |
Protection against input overcurrent, input undervoltage, output overvoltage, output current limiting, output shortcircuit, and overtemperature conditions. |
|
Support for redundancy |
Two power supplies can be connected in parallel to achieve 1+1 redundancy and load balancing. |
|
Support for hot swapping |
You can remove one of the power supplies in 1+1 redundancy when the switch is operating correctly. |
Technical specifications
Table4-4 Technical specifications
|
Item |
Specification |
|
Dimensions (H × W × D) |
40.2 × 50.5 × 246 mm (1.58 × 1.99 × 9.69 in), including the handle |
|
Weight |
0.7 kg (1.54 lb) |
|
Rated DC input voltage range |
–48 to –60 VDC |
|
Max DC input voltage range |
–36 to –72 VDC |
|
Rated input current |
10 A to 12 A |
|
Rated output current |
2 A to 37.5 A |
|
Rated output voltage |
3.3 V to 12 V |
|
Rated output power |
450 W |
|
Melting current of power supply fuse |
15 A/250 V |
5 Removable fan trays
Removable fan trays available for the S6526XE-HI switch series
LSPM1FANSA-SN
View
Figure5-1 LSPM1FANSA-SN fan tray view
LEDs
For information about the status LED, see "Fan tray status LED on a fan tray."
Features
The LSPM1FANSA-SN fan tray blows air from the power supply side to the port side. The fan tray features small size, fast heat dissipation, and hot swapping. It can automatically adjust the fan speed, providing powerful heat dissipation for the switch.
Technical specifications
Table5-1 Technical specifications
|
Item |
Specification |
|
Dimensions (H × W × D) |
40 × 40.6 × 105 mm (1.57 × 1.60 × 4.13 in), including the handle |
|
Fan quantity |
1 |
|
Weight |
N/A |
|
Airflow direction |
Air drawn in from the fan tray faceplate |
|
Fan speed |
20000 R.P.M |
|
Max airflow |
20 CFM (0.57 m3/min) |
|
Input voltage |
12 V |
|
Max power consumption |
9.8 W |
LSPM1FANSB-SN
View
Figure5-2 LSPM1FANSB-SN fan tray view
LEDs
For information about the status LED, see "Fan tray status LED on a fan tray."
Features
The LSPM1FANSB-SN fan tray draws air from the port side to the power supply side. The fan tray features small size, fast heat dissipation, and hot swapping. It can automatically adjust the fan speed, providing powerful heat dissipation for the switch.
Technical specifications
Table5-2 Technical specifications
|
Item |
Specification |
|
Dimensions (H × W × D) |
40 × 40.6 × 105 mm (1.57 × 1.60 × 4.13 in), including the handle |
|
Fan quantity |
1 |
|
Weight |
N/A |
|
Airflow direction |
Air exhausted from the fan tray faceplate |
|
Fan speed |
20000 R.P.M |
|
Max airflow |
20 CFM (0.57 m3/min) |
|
Input voltage |
12 V |
|
Max power consumption |
9.8 W |
Removable fan trays available for the S6526XE-EI switch series
FAN-40B-1-A
View
Figure5-3 FAN-40B-1-A fan tray view
LEDs
For information about the status LED, see "Fan tray status LED on a fan tray."
Features
The FAN-40B-1-A fan tray blows air from the power supply side to the port side. The fan tray features small size, fast heat dissipation, and hot swapping. It can automatically adjust the fan speed, providing powerful heat dissipation for the switch.
Technical specifications
Table5-3 Technical specifications
|
Item |
Specification |
|
Dimensions (H × W × D) |
40.6 × 40 × 117 mm (1.60 × 1.57 × 4.61 in), including the handle |
|
Fan quantity |
1 |
|
Weight |
N/A |
|
Airflow direction |
Air drawn in from the fan tray faceplate |
|
Fan speed |
21000 R.P.M |
|
Max airflow |
26 CFM (0.74 m3/min) |
|
Input voltage |
12 V |
|
Max power consumption |
27.72 W |
FAN-40F-1-A
View
Figure5-4 FAN-40F-1-A fan tray view
LEDs
For information about the status LED, see "Fan tray status LED on a fan tray."
Features
The FAN-40F-1-A fan tray draws air from the port side to the power supply side. The fan tray features small size, fast heat dissipation, and hot swapping. It can automatically adjust the fan speed, providing powerful heat dissipation for the switch.
Technical specifications
Table5-4 Technical specifications
|
Item |
Specification |
|
Dimensions (H × W × D) |
40.6 × 40 × 117 mm (1.60 × 1.57 × 4.61 in), including the handle |
|
Fan quantity |
1 |
|
Weight |
N/A |
|
Airflow direction |
Air exhausted from the fan tray faceplate |
|
Fan speed |
21000 R.P.M |
|
Max airflow |
26 CFM (0.74 m3/min) |
|
Input voltage |
12 V |
|
Max power consumption |
27.72 W |
6 Expansion cards
|
|
CAUTION: Do not hot swap the LSWM2XMGT4PM and LSWM2SP8PM expansion cards. |
LSWM2SP8P/LSWM2SP8PM
About LSWM2SP8P and LSWM2SP8PM
The LSWM2SP8PM and LSWM2SP8P interface cards each provide eight SFP+ ports. The SFP+ ports on the LSWM2SP8PM interface card support MACsec. The views of LSWM2SP8P and LSWM2SP8PM are the same. This figure uses the LSWM2SP8PM as an example.
Figure6-1 LSWM2SP8PM interface card view
Ports and LEDs
For information about the ports and transceiver modules and cables available for the ports, see "SFP+ port."
For information about the LEDs, see "SFP+ port LED."
Technical specifications
Table6-1 Technical specifications
|
Item |
Specification |
|
|
Product code |
LSWM2SP8P |
LSWM2SP8PM |
|
Dimensions (H × W × D) |
40.1 × 95 × 147.5 mm (1.58 × 3.74 × 5.81 in) |
40.1 × 95 × 147.5 mm (1.58 × 3.74 × 5.81 in) |
|
Weight |
0.4 kg (0.88 lb) |
0.688 kg (1.52 lb) |
|
Power consumption (static) |
9 W |
N/A |
|
Power consumption (typical) |
10 W |
N/A |
|
Power consumption (full load) |
14 W |
50 W |
LSWM2QP2P
About LSWM2QP2P
The LSWM2QP2P interface module provides two QSFP+ ports.
Figure6-2 LSWM2QP2P interface module view
Ports and LEDs
For information about the ports and transceiver modules and cables available for the ports, see "QSFP+ port."
For information about the LEDs, see "QSFP+ port LED."
Technical specifications
Table6-2 Technical specifications
|
Item |
Specification |
|
Dimensions (H × W × D) |
40.1 × 95 × 147.5 mm (1.58 × 3.74 × 5.81 in) |
|
Weight |
0.4 kg (0.88 lb) |
|
Power consumption (static) |
9 W |
|
Power consumption (typical) |
10 W |
|
Power consumption (full load) |
14 W |
LSWM2ZQP2P
About LSWM2ZQP2P
The LSWM2ZQP2P interface module provides two QSFP28 ports.
Figure6-3 LSWM2ZQP2P interface module view
Ports and LEDs
For information about the ports and transceiver modules and cables available for the ports, see "QSFP28 ports."
For information about the LEDs, see "QSFP28 port LED."
LSWM2ZSP8P
About LSWM2ZSP8P
The LSWM2ZSP8P interface module provides eight SFP28 ports.
|
|
NOTE: · Ports 1, 2, 3, and 4 of the expansion card have the same transmission rate, as do ports 5, 6, 7, and 8. · If you do not configure speed autonegotiation for a port, the actual port transmission rate depends on the setting of the speed command. For more information about the speed command, see the command reference for the switch. |
Figure6-4 LSWM2ZSP8P interface module view
Ports and LEDs
For information about the ports and transceiver modules and cables available for the ports, see "SFP28 port."
For information about the LEDs, see "SFP28 port LED."
LSPM6FWD
About LSPM6FWD
The LSPM6FWD is a fourth-generation high performance firewall module. It provides features including firewall, VPN, content filtering, content identification, URL filtering, and NAT. By using this module on a switch, you can enhance the switch security capabilities without changing the network topology.
Figure6-5 LSPM6FWD front panel
|
(1) Management Ethernet port LED (ACT/LINK) |
(2) 10/100/1000BASE-T management Ethernet port |
|
(3) System status LED (SYS) |
(4) Console port (CONSOLE) |
|
(5) Captive screw |
|
Ports and LEDs
For information about the ports and transceiver modules and cables available for the ports, see "Console port specifications (2)." and "Management Ethernet port specifications."
For information about the LEDs, see "LEDs on an LSPM6FWD firewall module."
Technical specifications
Table6-3 Technical specifications
|
Item |
Specification |
|
Dimensions (H × W × D) |
44.1 × 95 × 197.8 mm (1.74 × 3.74 × 7.79 in) |
|
Weight |
0.688 kg (1.52 lb) |
|
Power consumption (static) |
N/A |
|
Power consumption (typical) |
N/A |
|
Power consumption (full load) |
50 W |
LSWM2XMGT4PM
About LSWM2XMGT4PM
The LSWM2XMGT4PM interface module provides four 10G/5G/2.5G/1000BASE-T autosensing Ethernet ports that support MACsec.
Figure6-6 LSWM2XMGT4PM interface module view
|
(1) 10G/5G/2.5G/1000BASE-T Ethernet port |
(2) Captive screw |
|
(3) Ejector lever |
(4) Ethernet port LED |
Ports and LEDs
For information about the ports and transceiver modules and cables available for the ports, see "10G/5G/2.5G/1G autosensing Ethernet port."
For information about the LEDs, see "10G/5G/2.5G/1000BASE-T LEDs on an LSWM2XMGT4PM."
Technical specifications
Table6-4 Technical specifications
|
Item |
Specification |
|
Dimensions (H × W × D) |
40.1 × 95 × 147.5 mm (1.58 × 3.74 × 5.81 in) |
|
Weight |
≤ 0.29 kg (0.64 lb) |
|
Power consumption (static) |
N/A |
|
Power consumption (typical) |
13 W |
|
Power consumption (full load) |
15 W |
7 Ports and LEDs
Ports
Console port
Table7-1 Console port specifications (1)
|
Item |
Specification |
|
Connector type |
RJ-45 |
|
Compliant standard |
EIA/TIA-232 |
|
Port transmission rate |
9600 bps (default) to 115200 bps |
|
Services |
· Provides connection to an ASCII terminal · Provides connection to the serial port of a local PC running terminal emulation program |
|
Compatible devices |
All device models |
Table7-2 Console port specifications (2)
|
Item |
Specification |
|
Connector type |
RJ-45 |
|
Compliant standard |
RS-232 |
|
Port transmission rate |
9600 bps (default) to 115200 bps |
|
Transmission medium and max transmission distance |
≤ 15 m (49.21 ft) over a common asynchronous serial interface cable |
|
Services |
· Provides connection to an ASCII terminal · Provides connection to the serial port of a local PC running terminal emulation program · Supports command line interface (CLI) |
|
Compatible devices |
LSPM6FWD |
Table7-3 Type-C USB console port specifications
|
Item |
Specification |
|
Connector type |
USB Type-C |
|
Compliant standard |
USB2.0 |
|
Port transmission rate |
9600 bps (default) to 115200 bps |
|
Services |
· Provides connection to an ASCII terminal · Provides connection to the serial port of a local PC running terminal emulation program |
|
Compatible devices |
All device models |
Management Ethernet port
Table7-4 Management Ethernet port specifications
|
Item |
Specification |
|
Connector type |
RJ-45 |
|
Rate, duplex mode, and auto-MDI/MDI-X |
· 10 Mbps, half/full duplex · 100 Mbps, half/full duplex · 1000 Mbps, full duplex · MDI/MDI-X autosensing |
|
Transmission medium |
Category-5 or above twisted pair cable |
|
Max transmission distance |
100 m (328.08 ft) |
|
Compliant standard |
IEEE 802.3i, 802.3u, and 802.3ab |
|
Functions and services |
Used for upgrading and managing applications and Boot ROM |
|
Compatible devices |
All device models |
USB port
Table7-5 USB port specifications
|
Item |
Specification |
|
Port type |
USB 2.0 |
|
Compliant standard |
OHC |
|
Port transmission rate |
Uploads and downloads data at a rate up to 480 Mbps |
|
Functions and services |
Accesses the file system on the flash of the switch, for example, to upload or download application and configuration files |
|
Compatible devices |
All device models |
|
|
NOTE: USB devices from different vendors vary in compatibilities and drivers. H3C does not guarantee correct operation of USB devices from other vendors on the switch. If a USB device fails to operate on the switch, replace it with one from another vendor. |
10G/5G/2.5G/1G autosensing Ethernet port
Table7-6 10G/5G/2.5G/1G autosensing Ethernet port specifications
|
Item |
Specification |
|
Connector type |
RJ-45 |
|
Rate, duplex mode, and auto-MDI/MDI-X |
· 10 Gbps, full duplex · 5 Gbps, full duplex · 2.5 Gbps, full duplex · 1 Gbps, full duplex · MDI/MDI-X autosensing |
|
Max transmission distance |
10G mode: · 55 m (180.45 ft) over Category-5e twisted pair cable · 55 m (180.45 ft) over Category-6 unshielded twisted pair cable · 100 m (328.08 ft) over Category-6 or above shielded twisted pair cable 5G mode: 100 m (328.08 ft) over Category-5e or above twisted pair cable 2.5G mode: 200 m (656.17 ft) over Category-5e or above twisted pair cable 1G mode: 140 m (459.32 ft) over Category-5 or above twisted pair cable |
|
Transmission medium |
Category-5e or above twisted pair cable |
|
Compliant standard |
IEEE 802.3an and IEEE 802.3ab |
|
Compatible devices |
LSWM2XMGT4PM |
SFP+ port
Table7-7 SFP+ port specifications
|
Item |
Specification |
|
Port type |
SFP+ port |
|
Compatible transceiver modules and cables |
· GE SFP transceiver modules and cables in Table7-8 · 10GE SFP+ transceiver modules and cables in Table7-9, Table7-10, and Table7-11 |
|
Compatible devices |
All device models, LSWM2SP8P, LSWM4SP8PM |
Table7-8 GE SFP transceiver modules and cables available for the SFP+ ports
|
GE SFP transceiver module and cable |
Central wavelength (nm) |
Connector |
Cable/Fiber type and diameter (µm) |
Modal bandwidth (MHz × km) |
Max transmission distance |
|
SFP copper transceiver modules |
|||||
|
SFP-GE-T |
N/A |
RJ-45 |
Twisted pair cable |
N/A |
100 m (328.08 ft) |
|
SFP-GE-T-D |
N/A |
RJ-45 |
Twisted pair cable |
N/A |
100 m (328.08 ft) |
|
SFP optical transceiver modules |
|||||
|
SFP-GE-SX-MM850-A |
850 |
LC |
Multi-mode, 50/125 |
500 |
550 m (1804.46 ft) |
|
400 |
500 m (1640.42 ft) |
||||
|
Multi-mode, 62.5/125 |
200 |
275 m (902.23 ft) |
|||
|
160 |
220 m (721.78 ft) |
||||
|
SFP-GE-SX-MM850-S |
850 |
LC |
Multi-mode, 50/125 |
500 |
550 m (1804.46 ft) |
|
400 |
500 m (1640.42 ft) |
||||
|
Multi-mode, 62.5/125 |
200 |
275 m (902.23 ft) |
|||
|
160 |
220 m (721.78 ft) |
||||
|
SFP-GE-SX-MM850-D |
850 |
LC |
Multi-mode, 50/125 |
500 |
550 m (1804.46 ft) |
|
400 |
500 m (1640.42 ft) |
||||
|
Multi-mode, 62.5/125 |
200 |
275 m (902.23 ft) |
|||
|
160 |
220 m (721.78 ft) |
||||
|
SFP-GE-LX-SM1310-A |
1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
Multi-mode, 50/125 |
500 or 400 |
550 m (1804.46 ft) |
|||
|
Multi-mode, 62.5/125 |
500 |
550 m (1804.46 ft) |
|||
|
SFP-GE-LX-SM1310-D |
1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-GE-LX-SM1310-S |
1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-GE-LX-SM1310-F |
1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-GE-LX10-SM1310 |
1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-GE-LH40-SM1310 |
1310 |
LC |
Single-mode, 9/125 |
N/A |
40 km (24.86 miles) |
|
SFP-GE-LH40-SM1310-D |
1310 |
LC |
Single-mode, 9/125 |
N/A |
40 km (24.86 miles) |
|
SFP-GE-LH40-SM1310-S |
1310 |
LC |
Single-mode, 9/125 |
N/A |
40 km (24.86 miles) |
|
SFP-GE-LH40-SM1550 |
1550 |
LC |
Single-mode, 9/125 |
N/A |
40 km (24.86 miles) |
|
SFP-GE-LH80-SM1550 |
1550 |
LC |
Single-mode, 9/125 |
N/A |
80 km (49.71 miles) |
|
SFP-GE-LH80-SM1550-D |
1550 |
LC |
Single-mode, 9/125 |
N/A |
80 km (49.71 miles) |
|
SFP-GE-LH100-SM1550 |
1550 |
LC |
Single-mode, 9/125 |
N/A |
100 km (62.14 miles) |
|
SFP-GE-LX-SM1310-BIDI |
TX: 1310 RX: 1490 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-GE-LX-SM1490-BIDI |
TX: 1490 RX: 1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-GE-LH70-SM1490-BIDI |
TX: 1490 RX: 1550 |
LC |
Single-mode, 9/125 |
N/A |
70 km (43.50 miles) |
|
SFP-GE-LH70-SM1550-BIDI |
TX: 1550 RX: 1490 |
LC |
Single-mode, 9/125 |
N/A |
70 km (43.50 miles) |
|
SFP-GE-LH40-SM1310-BIDI |
TX: 1310 RX: 1550 |
LC |
Single-mode, 9/125 |
N/A |
40 km (24.86 miles) |
|
SFP-GE-LH40-SM1550-BIDI |
TX: 1550 RX: 1310 |
LC |
Single-mode, 9/125 |
N/A |
40 km (24.86 miles) |
|
SFP-GE-LX-SM1310-BIDI-S |
TX: 1310 RX: 1490 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-GE-LX-SM1490-BIDI-S |
TX: 1490 RX: 1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP copper cable |
|||||
|
SFP-STACK-Kit |
N/A |
N/A |
SFP cable |
N/A |
1.5 m (4.92 ft) |
|
SFP-STACK-Kit-S |
N/A |
N/A |
SFP cable |
N/A |
1.5 m (4.92 ft) |
|
|
IMPORTANT: The following transceiver modules must be used in pairs: · SFP-GE-LX-SM1310-BIDI and SFP-GE-LX-SM1490-BIDI transceiver modules. · SFP-GE-LH70-SM1490-BIDI and SFP-GE-LH70-SM1550-BIDI transceiver modules. · SFP-GE-LH40-SM1310-BIDI and SFP-GE-LH40-SM1550-BIDI transceiver modules. · SFP-GE-LX-SM1310-BIDI-S and SFP-GE-LX-SM1490-BIDI-S transceiver modules. For example, if one end uses the SFP-GE-LX-SM1310-BIDI transceiver module, the other end must use the SFP-GE-LX-SM1490-BIDI transceiver module. |
Table7-9 10GE SFP+ transceiver modules available for the SFP+ ports
|
10GE SFP+ transceiver module |
Central wavelength (nm) |
Connector |
Fiber diameter (µm) |
Modal bandwidth (MHz × km) |
Max transmission distance |
|
SFP-XG-SX-MM850-A |
850 |
LC |
Multi-mode, 50/125 |
2000 |
300 m (984.25 ft) |
|
500 |
82 m (269.03 ft) |
||||
|
400 |
66 m (216.54 ft) |
||||
|
Multi-mode, 62.5/125 |
200 |
33 m (108.27 ft) |
|||
|
160 |
26 m (85.30 ft) |
||||
|
SFP-XG-SX-MM850-E |
850 |
LC |
Multi-mode, 50/125 |
2000 |
300 m (984.25 ft) |
|
500 |
82 m (269.03 ft) |
||||
|
400 |
66 m (216.54 ft) |
||||
|
Multi-mode, 62.5/125 |
200 |
33 m (108.27 ft) |
|||
|
160 |
26 m (85.30 ft) |
||||
|
SFP-XG-SX-MM850-D |
850 |
LC |
Multi-mode, 50/125 |
2000 |
300 m (984.25 ft) |
|
500 |
82 m (269.03 ft) |
||||
|
400 |
66 m (216.54 ft) |
||||
|
Multi-mode, 62.5/125 |
200 |
33 m (108.27 ft) |
|||
|
160 |
26 m (85.30 ft) |
||||
|
SFP-XG-SX-MM850-S |
850 |
LC |
Multi-mode, 50/125 |
2000 |
300 m (984.25 ft) |
|
500 |
82 m (269.03 ft) |
||||
|
400 |
66 m (216.54 ft) |
||||
|
Multi-mode, 62.5/125 |
200 |
33 m (108.27 ft) |
|||
|
160 |
26 m (85.30 ft) |
||||
|
SFP-XG-LX-SM1310 |
1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-XG-LX-SM1310-E |
1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-XG-LX-SM1310-D |
1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-XG-LX-SM1310-S |
1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-XG-LX-SM1310-F |
1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-XG-CPRI-IR-SM1310 |
1310 |
LC |
Single-mode, 9/125 |
N/A |
1.4 km (0.87 miles) |
|
SFP-XG-CPRI-LR-SM1310 |
1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-XG-LH40-SM1550 |
1550 |
LC |
Single-mode, 9/125 |
N/A |
40 km (24.86 miles) |
|
SFP-XG-LH40-SM1550-D |
1550 |
LC |
Single-mode, 9/125 |
N/A |
40 km (24.86 miles) |
|
SFP-XG-LH80-SM1550 |
1550 |
LC |
Single-mode, 9/125 |
N/A |
80 km (49.71 miles) |
|
SFP-XG-LH80-SM1550-D |
1550 |
LC |
Single-mode, 9/125 |
N/A |
80 km (49.71 miles) |
|
SFP-XG-LX-SM1270-BIDI |
TX: 1270 RX: 1330 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-XG-LX-SM1330-BIDI |
TX: 1330 RX: 1270 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-XG-LX-SM1270-BIDI-S |
TX: 1270 RX: 1330 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-XG-LX-SM1330-BIDI-S |
TX: 1330 RX: 1270 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-XG-LH40-SM1270-BIDI |
TX: 1270 RX: 1330 |
LC |
Single-mode, 9/125 |
N/A |
40 km (24.86 miles) |
|
SFP-XG-LH40-SM1330-BIDI |
TX: 1330 RX: 1270 |
LC |
Single-mode, 9/125 |
N/A |
40 km (24.86 miles) |
|
SFP-XG-LH80-SM1550-BIDI |
TX: 1550 RX: 1490 |
LC |
Single-mode, 9/125 |
N/A |
80 km (49.71 miles) |
|
SFP-XG-LH80-SM1490-BIDI |
TX: 1490 RX: 1550 |
LC |
Single-mode, 9/125 |
N/A |
80 km (49.71 miles) |
|
|
IMPORTANT: The following transceiver modules must be used in pairs: · SFP-XG-LX-SM1270-BIDI and SFP-XG-LX-SM1330-BIDI transceiver modules. · SFP-XG-LX-SM1270-BIDI-S and SFP-XG-LX-SM1330-BIDI-S transceiver modules. · SFP-XG-LH40-SM1270-BIDI and SFP-XG-LH40-SM1330-BIDI transceiver modules. · SFP-XG-LH80-SM1550-BIDI and SFP-XG-LH80-SM1490-BIDI transceiver modules. For example, if one end uses an SFP-XG-LX-SM1270-BIDI transceiver module, the other end must use an SFP-XG-LX-SM1330-BIDI transceiver module. |
Table7-10 SFP+ copper cables available for the SFP+ ports
|
SFP+ copper cable |
Cable length |
|
LSWM1STK |
0.65 m (2.13 ft) |
|
LSWM2STK |
1.2 m (3.94 ft) |
|
LSWM3STK |
3 m (9.84 ft) |
|
LSTM1STK |
5 m (16.40 ft) |
Table7-11 SFP+ fiber cables available for the SFP+ ports
|
SFP+ fiber cable |
Cable length |
|
SFP-XG-D-AOC-7M |
7 m (22.97 ft) |
|
SFP-XG-D-AOC-10M |
10 m (32.81 ft) |
|
SFP-XG-D-AOC-20M |
20 m (65.62 ft) |
Figure7-1 SFP+ cable
|
(1) Connector |
(2) Pull latch |
|
|
NOTE: · As a best practice, use H3C transceiver modules and network cables for the switch. · The H3C transceiver modules and network cables are subject to change over time. For the most recent list of H3C transceiver modules and cables, contact H3C Support or marketing staff. · For the specifications of H3C transceiver modules and network cables, see H3C Transceiver Modules User Guide. |
SFP28 port
Table7-12 SFP28 port specifications
|
Item |
Specification |
|
Port type |
SFP28 port |
|
Compatible transceiver modules and cables |
· SFP28 transceiver modules and cables in Table7-13 and Table7-14 · 10GE SFP+ transceiver modules and cables in Table7-9, Table7-10, and Table7-11 |
|
Compatible devices |
LSWM2ZSP8P |
Table7-13 SFP28 transceiver modules available for the SFP28 ports
|
SFP28 transceiver module |
Central wavelength (nm) |
Connector |
Cable/Fiber type and diameter (µm) |
Modal bandwidth (MHz × km) |
Max transmission distance |
|
SFP-25G-LR-SM1310 |
1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-25G-SR-MM850 |
850 |
LC |
Multi-mode, 50/125 |
2000 |
70 m (229.66 ft) |
|
4700 |
100 m (328.08 ft) |
||||
|
SFP-25G-LR-SM1310-I |
1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-25G-LR-SM1310-F |
1310 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
SFP-25G-CSR-MM850 |
850 |
MMF |
Multi-mode, 50/125 |
2000 |
200 m (656.17 ft) |
|
> 3500 |
300 m (984.25 ft) |
||||
|
> 5500 |
400 m (1312.34 ft) |
Table7-14 SFP28 cables available for the SFP28 ports
|
SFP28 cable |
Cable length |
|
SFP-25G-D-CAB-1M |
1 m (3.28 ft) |
|
SFP-25G-D-CAB-3M |
3 m (9.84 ft) |
|
SFP-25G-D-CAB-5M |
5 m (16.40 ft) |
|
SFP-25G-D-AOC-3M |
3 m (9.84 ft) |
|
SFP-25G-D-AOC-5M |
5 m (16.40 ft) |
|
SFP-25G-D-CAB-5M-A |
5 m (16.40 ft) |
|
SFP-25G-D-AOC-7M |
7 m (22.97 ft) |
|
SFP-25G-D-AOC-10M |
10 m (32.81 ft) |
|
SFP-25G-D-AOC-20M |
20 m (65.62 ft) |
|
(1) Connector |
(2) Pull latch |
|
|
NOTE: · As a best practice, use H3C transceiver modules and cables for the switch. · The H3C transceiver modules and cables are subject to change over time. For the most recent list of H3C transceiver modules and cables, contact your H3C Support or marketing staff. · For more information about H3C transceiver modules and cables, see H3C Transceiver Modules User Guide. |
QSFP+ port
Table7-15 QSFP+ port specifications
|
Item |
Specification |
|
Port type |
QSFP+ port |
|
Compatible transceiver modules and cables |
· QSFP+ transceiver modules and cables in Table7-16, Table7-17, and Table7-18 |
|
Compatible devices |
LSWM2QP2P |
|
|
NOTE: You can use a QSFP-40G-SR4-MM850 or QSFP-40G-CSR4-MM850 transceiver module to connect one 40G port to four 10G ports. The QSFP+ transceiver module and SFP+ transceiver modules to be connected must be the same in specifications, including central wavelength and fiber type. |
Table7-16 40G QSFP+ transceiver modules available for the QSFP+ ports
|
QSFP+ transceiver module |
Central wavelength (nm) |
Connector |
Fiber type and diameter (µm) |
Modal bandwidth (MHz × km) |
Max transmission distance |
|
QSFP-40G-SR4-MM850 |
850 |
MPO (PC end, 12 cores) |
Multi-mode, 50/125 |
2000 |
100 m (328.08 ft) |
|
4700 |
150 m (492.13 ft) |
||||
|
QSFP-40G-CSR4-MM850 |
850 |
MPO (PC end, 12 cores) |
Multi-mode, 50/125 |
2000 |
300 m (984.25 ft) |
|
4700 |
400 m (1312.34 ft) |
||||
|
QSFP-40G-BIDI-SR-MM850 |
850 |
LC |
Multi-mode, 50/125 |
2000 |
100 m (328.08 ft) |
|
4700 |
150 m (492.13 ft) |
||||
|
QSFP-40G-BIDI-WDM850 |
Four lanes: · 850 · 880 · 910 · 940 |
LC |
Multi-mode, 50/125 |
2000 |
240 m (787.40 ft) |
|
4700 |
350 m (1148.29 ft) |
||||
|
QSFP-40G-LR4-WDM1300 |
Four lanes: · 1271 · 1291 · 1311 · 1331 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
QSFP-40G-LX4-WDM1300 |
Four lanes: · 1271 · 1291 · 1311 · 1331 |
LC |
Multi-mode, 50/125 |
2000 |
150 m (492.13 ft) |
|
4700 |
|||||
|
QSFP-40G-ER4-WDM1300 |
Four lanes: · 1271 · 1291 · 1311 · 1331 |
LC |
Single-mode, 9/125 |
N/A |
40 km (24.86 miles) |
|
QSFP-40G-LR4L-WDM1300 |
Four lanes: · 1271 · 1291 · 1311 · 1331 |
LC |
Single-mode, 9/125 |
N/A |
2 km (1.24 miles) |
Table7-17 40G QSFP+ copper cables available for the QSFP+ ports
|
QSFP+ copper cable |
Max transmission distance |
|
LSWM1QSTK0 |
1 m (3.28 ft) |
|
LSWM1QSTK1 |
3 m (9.84 ft) |
|
LSWM1QSTK2 |
5 m (16.40 ft) |
Table7-18 40G QSFP+ fiber cables available for the QSFP+ ports
|
QSFP+ fiber cable |
Max transmission distance |
|
QSFP-40G-D-AOC-3M |
3 m (9.84 ft) |
|
QSFP-40G-D-AOC-7M |
7 m (22.97 ft) |
|
QSFP-40G-D-AOC-20M |
20 m (65.62 ft) |
|
|
NOTE: MPO connectors include physical contact (PC) connectors with a flat-polished face and angle-polished contact (APC) connectors with an angle-polished face (8°). |
QSFP28 ports
Table7-19 QSFP28 port specifications
|
Item |
Specification |
|
Port type |
QSFP28 port |
|
Compatible transceiver modules and cables |
· QSFP28 transceiver modules and cables in Table7-20, Table7-21, and Table7-22 · QSFP+ transceiver modules and cables in Table7-16, Table7-17, and Table7-18 |
|
Compatible devices |
All device models |
|
Restrictions and guidelines |
On an S6526XE-48X6CC-HI switch with no expansion card installed, up to two ports each can be split into four breakout interfaces. You can select one port from each option: · Port 49, 50, or 51 on the switch. · Port 52, 53, or 54 on the switch. On an S6526XE-48X4CC-EI switch with no expansion card installed, ports 49, 50, 51, and 52 on the switch each can be split into four breakout interfaces. |
|
|
NOTE: You can use a QSFP-100G-SR4-MM850 transceiver module to connect one 100G port to four 25G ports. The QSFP+ transceiver module and SFP28 transceiver modules to be connected must be the same in specifications, including central wavelength and fiber type. |
Table7-20 100G QSFP28 transceiver modules available for the QSFP28 ports
|
QSFP28 transceiver module |
Central wavelength (nm) |
Connector |
Fiber type and diameter (µm) |
Modal bandwidth (MHz*km) |
Maximum transmission distance |
|
QSFP-100G-SR4-MM850 |
850 |
MPO (PC end, 12 cores) |
Multi-mode, 50/125 |
2000 |
70 m (229.66 ft) |
|
4700 |
100 m (328.08 ft) |
||||
|
QSFP-100G-eSR4-MM850 |
850 |
LC |
Multi-mode, 50/125 |
4700 |
300 m (984.25 ft) |
|
QSFP-100G-SWDM4-MM850 |
Four lanes: · 850 · 880 · 910 · 940 |
LC |
Multi-mode, 50/125 |
2000 |
75 m (246.06 ft) |
|
4700 |
100 m (328.08 ft) |
||||
|
QSFP-100G-LR4-WDM1300 |
Four lanes: · 1295 · 1300 · 1304 · 1309 |
LC |
Single-mode, 9/125 |
N/A |
10 km (6.21 miles) |
|
QSFP-100G-LR4L-WDM1300 |
Four lanes: · 1271 · 1291 · 1311 · 1331 |
LC |
Single-mode, 9/125 |
N/A |
2 km (1.24 miles) |
|
QSFP-100G-CWDM4-SM1300-A |
Four lanes: · 1271 · 1291 · 1311 · 1331 |
LC |
Single-mode, 9/125 |
N/A |
2 km (1.24 miles) |
|
QSFP-100G-ER4L-WDM1300 |
Four lanes: · 1295.56 · 1300.05 · 1304.58 · 1309.14 |
LC |
Single-mode, 9/125 |
N/A |
40 km (24.86 miles) |
|
QSFP-100G-ER4-WDM1300 |
Four lanes: · 1295.56 · 1300.05 · 1304.58 · 1309.14 |
LC |
Single-mode, 9/125 |
N/A |
40 km (24.86 miles) |
|
QSFP-100G-ZR4-WDM1300 |
Four lanes: · 1295.56 · 1300.05 · 1304.58 · 1309.14 |
LC |
Single-mode, 9/125 |
N/A |
80 km (49.71 miles) |
|
QSFP-100G-FR1-SM1310 |
1310 |
LC |
Single-mode, 9/125 |
N/A |
2 km (1.24 miles) |
Table7-21 100G QSFP28 copper cables available for the QSFP28 ports
|
QSFP28 fiber cable |
Cable length |
|
QSFP-100G-D-CAB-1M |
1 m (3.28 ft) |
|
QSFP-100G-D-CAB-3M |
3 m (9.84 ft) |
|
QSFP-100G-D-CAB-5M |
5 m (16.40 ft) |
Table7-22 100G QSFP28 fiber cables available for the QSFP28 ports
|
QSFP28 copper cable |
Cable length |
|
QSFP-100G-D-AOC-10M |
10 m (32.81 ft) |
|
QSFP-100G-D-AOC-20M |
20 m (65.62 ft) |
Figure7-3 100G QSFP28 copper cable
|
(1) Connector |
(2) Pull tab |
|
|
NOTE: · As a best practice, use H3C transceiver modules and cables for the switch. · The H3C transceiver modules and cables are subject to change over time. For the most recent list of H3C transceiver modules and cables, contact your H3C Support or marketing staff. · For more information about H3C transceiver modules and cables, see H3C Transceiver Modules User Guide. |
Ports on an LSPM6FWD firewall module
Table7-23 Console port specifications
|
Item |
Specification |
|
Connector type |
RJ-45 |
|
Compliant standard |
RS-232 |
|
Port transmission rate |
9600 bps (default) to 115200 bps |
|
Transmission medium and max transmission distance |
≤ 15 m (49.21 ft) over a common asynchronous serial interface cable |
|
Services |
· Provides connection to an ASCII terminal · Provides connection to the serial port of a local PC running terminal emulation program · Supports CLI |
LEDs
System status LED
The system status LED shows the operating status of the switch.
Table7-24 System status LED description
|
LED mark |
Status |
Description |
|
SYS |
Steady green |
The switch has started correctly. |
|
Flashing green (1 Hz) |
The switch is performing power-on self test (POST). |
|
|
Steady red |
The switch has failed the POST or is faulty. |
|
|
Flashing red (1 Hz) |
The system is faulty. |
|
|
Off |
The switch is powered off. |
Power status LED
The two power status LEDs show the operating status of a power supply.
Table7-25 Power status LED description
|
LED status |
Description |
|
Steady green |
The power supply is operating correctly and is in primary state. |
|
Flashing green |
The power supply is operating correctly and is in standby state. |
|
Steady red |
The power supply is faulty or has entered a protection state. |
|
Alternating between red and green |
One of the following power supply conditions is present but the power supply has not entered a protection state: output overvoltage, output undervoltage, output overcurrent, output power overload, or overtemperature. |
|
Flashing red |
The current power supply does not have power input. If a device has two power supplies, one of which has power input but the other does not, the LED on the power supply without power input flashes red. |
|
Off |
No power input. |
Management Ethernet port LED
Table7-26 Management Ethernet port LED description
|
LED mark |
Status |
Description |
|
LINK |
Off |
No link is present on the port. |
|
Steady green |
The port is operating at 10/100/1000 Mbps. |
|
|
ACT |
Off |
The port is not sending or receiving data. |
|
Flashing yellow |
The port is sending or receiving data. |
SFP+ port LED
Table7-27 SFP+ port LED description
|
LED status |
Description |
|
Steady green |
A module has been installed and the port is operating at 10 Gbps. |
|
Flashing green |
The port is sending or receiving data at 10 Gbps. |
|
Steady yellow |
A module has been installed and the port is operating at 1 Gbps. |
|
Flashing yellow |
The port is sending or receiving data at 1 Gbps. |
|
Off |
No module has been installed or no link is present on the port. |
SFP28 port LED
Table7-28 SFP28 port LED description
|
LED status |
Description |
|
Steady green |
The port is operating at 25 Gbps. |
|
Flashing green |
The port is sending or receiving data at 25 Gbps. |
|
Steady yellow |
The port is operating at 10 Gbps. |
|
Flashing yellow |
The port is sending or receiving data at 10 Gbps. |
|
Off |
No module has been installed or no link is present on the port. |
QSFP+ port LED
Table7-29 QSFP+ port LED description
|
LED status |
Description |
|
Steady green |
A module has been installed and the port is operating at 40 Gbps. |
|
Flashing green |
The port is sending or receiving data at 40 Gbps. |
|
Steady yellow |
A module has been installed and the port is operating at 10 Gbps. |
|
Flashing yellow |
The port is sending or receiving data at 10 Gbps. |
|
Off |
No module has been installed or no link is present on the port. |
QSFP28 port LED
Table7-30 QSFP28 port LED description
|
LED status |
Description |
|
Steady green |
A module has been installed and the port is operating at 100 Gbps. |
|
Flashing green |
The port is sending or receiving data at 100 Gbps. |
|
Steady yellow |
A module has been installed and the port is operating at 40 Gbps. |
|
Flashing yellow |
The port is sending or receiving data at 40 Gbps, 25 Gbps or 10 Gbps. |
|
Off |
No module has been installed or no link is present on the port. |
Expansion card status LED
The switch provides expansion slots at the rear. The expansion card status LED on the front panel indicates the operating status of the expansion card.
Table7-31 Expansion card status LED description
|
LED mark |
Status |
Description |
|
SLOT |
Steady green |
The expansion card is operating correctly. |
|
Flashing yellow |
The switch does not support the expansion card model, or the expansion card is faulty. |
|
|
Off |
The expansion slot is empty. |
Fan tray status LED on a fan tray
The LSPM1FANSA-SN and LSPM1FANSB-SN fan trays each have a LED to indicate the fan tray operating status.
Table7-32 Description for the status LED on the LSPM1FANSA-SN or LSPM1FANSB-SN fan tray
|
LED mark |
Status |
Description |
|
FAN |
On |
The fan tray is faulty. |
|
Off |
The fan tray is operating correctly. |
The FAN-40B-1-A and FAN-40F-1-A fan trays each have a LED to indicate the fan tray operating status.
Table7-33 Description for the status LED on the FAN-40B-1-A or FAN-40F-1-A fan tray
|
LED mark |
Status |
Description |
|
FAN |
Steady yellow |
The fan tray is operating correctly. |
|
Flashing |
The fan tray is operating incorrectly. |
|
|
Off |
The fan tray is not securely installed or has no power input. |
LEDs on an LSPM6FWD firewall module
Table7-34 Description for the LEDs on an LSPM6FWD firewall module
|
LED |
Mark |
Status |
Description |
|
Management Ethernet port LED |
ACT/LINK |
Off |
No link is present on the port. |
|
Steady green |
A link is present on the port. |
||
|
Flashing green |
The port is sending or receiving data. |
||
|
System status LED |
SYS |
Off |
No power is input or the firewall module has failed. |
|
Slowly flashing green |
The system has started up and is operating correctly. |
||
|
Fast flashing green |
The system is loading software. |
10G/5G/2.5G/1000BASE-T LEDs on an LSWM2XMGT4PM
Table7-35 Description for the 10G/5G/2.5G/1000BASE-T LEDs on an LSWM2XMGT4PM
|
LED status |
Description |
|
Steady green |
The port is operating at 10 Gbps. |
|
Flashing green |
The port is sending or receiving data at 10 Gbps. |
|
Steady yellow |
The port is operating at 1 Gbps, 2.5 Gbps, or 5 Gbps. |
|
Flashing yellow |
The port is sending or receiving data at 1 Gbps, 2.5 Gbps, or 5 Gbps. |
|
Off |
No link is present on the port. |
8 Cooling system
To dissipate heat timely and enhance system stability, the switch uses a high-performance cooling system. Consider the site ventilation design when you plan the installation site for the switch.
The switch uses removable fan trays and provides airflow from the port side to the power supply side or from the power supply side to the port side by using different types of fan trays. You must fully configure the switch with fan trays of the same model. Table8-1 describes the fan trays available for the switch.
Table8-1 Fan trays available for the switch
|
Switch model |
Fan tray model |
Airflow direction |
|
S6526XE-32X6CC-HI S6526XE-48X6CC-HI |
LSPM1FANSA-SN |
From the power supply side to the port side |
|
LSPM1FANSB-SN |
From the port side to the power supply side |
|
|
S6526XE-32X4CC-EI S6526XE-48X4CC-EI |
FAN-40F-1-A |
From the power supply side to the port side |
|
FAN-40B-1-A |
From the port side to the power supply side |
Figure8-1 Airflow direction for LSPM1FANSA-SN or FAN-40F-1-A
Figure8-2 Airflow direction for LSPM1FANSB-SN or FAN-40B-1-A
