classifier-name: Specifies a traffic class by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a traffic class, this command displays all traffic classes.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays the traffic classes for the master device. ‌‌

Examples

# Display all user-defined traffic classes.

<Sysname> display traffic classifier user-defined

User-defined classifier information:

Classifier: 1 (ID 100)

Operator: AND

Rule(s) :

If-match acl 2000

Classifier: 2 (ID 101)

Operator: AND

Rule(s) :

If-match protocol ipv6

Classifier: 3 (ID 102)

Operator: AND

Rule(s) :

-none-

Table 1 Command output

Field	Description
Classifier	Traffic class name and its match criteria.
Operator	Match operator you set for the traffic class. If the operator is AND, the traffic class matches the packets that match all its match criteria. If the operator is OR, the traffic class matches the packets that match any of its match criteria.
Rule(s)	Match criteria.

if-match

Use if-match to define a match criterion.

Use undo if-match to delete a match criterion.

Syntax

if-match match-criteria

undo if-match match-criteria

Default

No match criterion is configured.

Views

Traffic class view

Predefined user roles

network-admin

Parameters

match-criteria: Specifies a match criterion. Table 2 shows the available match criteria.

Table 2 Available match criteria

Option	Description
acl [ ipv6 \| mac \| user-defined ] { acl-number \| name acl-name }	Matches an ACL. The value range for the acl-number argument is as follows: · 2000 to 3999 for IPv4 ACLs. · 2000 to 3999 for IPv6 ACLs. · 4000 to 4999 for Layer 2 ACLs. · 5000 to 5999 for user-defined ACLs. The acl-name argument is a case-insensitive string of 1 to 63 characters, which must start with an English letter. To avoid confusion, make sure the argument is not all. If no VPN instance is specified in an ACL rule, the ACL rule takes effect on both non-VPN packets and VPN packets.
any	Matches all packets.
control-plane protocol protocol-name&<1-8>	Matches control plane protocols. The protocol-name&<1-8> argument specifies a space-separated list of up to eight system-defined control plane protocols. For available system-defined control plane protocols, see Table 3.
control-plane protocol-group protocol-group-name	Matches a control plane protocol group. The protocol-group-name argument can be critical, important, management, monitor, normal, or redirect.
customer-dot1p dot1p-value	Matches 802.1p priority values in inner VLAN tags of double-tagged packets. Thedot1p-value argument specifies an 802.1p priority value in the range of 0 to 7.
customer-vlan-id vlan-id-list	Matches VLAN IDs in inner VLAN tags of double-tagged packets. The vlan-id-list argument specifies a space-separated list of up to 10 VLAN items. Each item specifies a VLAN or a range of VLANs in the form of vlan-id1 to vlan-id2. The value for vlan-id2 must be greater than or equal to the value for vlan-id1. The value range for the vlan-id argument is 1 to 4094.
destination-mac mac-address [ mac-address-mask ]	Matches a destination MAC address. This option takes effect only on Ethernet interfaces.
dscp dscp-value	Matches DSCP values. The dscp-value argument specifies a DSCP value. The value range for the dscp-value argument is 0 to 63 or keywords shown in Table 5.
forwarding-layer { bridge \| route }	Matches Layer 2 forwarded packets or Layer 3 forwarded packets. · bridge—Matches Layer 2 forwarded packets. · route—Matches Layer 3 forwarded packets.
ip-precedence ip-precedence-value	Matches IP precedence values. The ip-precedence-value argument specifies an IP precedence value in the range of 0 to 7.
outbound-interface interface-type interface-number	Matches an output interface specified by its type and number. This option take effects only on outgoging packets of Layer 2 Ethernet interfaces and Layer 3 Ethernet interfaces.
protocol protocol-name	Matches a protocol. The protocol-name argument can be ip or ipv6.
service-dot1p dot1p-value	Matches 802.1p priority values in outer VLAN tags. The dot1p-value argument specifies an 802.1p priority value in the range of 0 to 7.
service-vlan-id vlan-id-list	Matches VLAN IDs in outer VLAN tags. The vlan-id-list argument specifies a space-separated list of up to 10 VLAN items. Each item specifies a VLAN or a range of VLANs in the form of vlan-id1 to vlan-id2. The value for vlan-id2 must be greater than or equal to the value for vlan-id1. The value range for the vlan-id argument is 1 to 4094. You can use this option to match single-tagged packets.
source-mac mac-address [ mac-address-mask ]	Matches a source MAC address. This option takes effect only on Ethernet interfaces.

Table 3 Available system-defined control plane protocols

Protocol	Description
arp	ARP packets
arp-snooping	ARP snooping packets
bfd	BFD packets
bgp	BGP packets
bgp4+	IPv6 BGP packets
dhcp	DHCP packets
dhcp-snooping	DHCP snooping packets
dhcp6	IPv6 DHCP packets
dot1x	802.1X packets
icmp	ICMP packets
icmp6	ICMPv6 packets
isis	IS-IS packets
lacp	LACP packets
ldp	LDP packets
ldp6	IPv6 LDP packets
lldp	LLDP packets
msdp	MSDP packets
mvrp	MVRP packets (including GVRP packets)
ntp	NTP packets
oam	OAM packets
ospf-multicast	OSPF multicast packets
ospf-unicast	OSPF unicast packets
ospf3-multicast	OSPFv3 multicast packets
ospf3-unicast	OSPFv3 unicast packets
pim-multicast	PIM multicast packets
pim-unicast	PIM unicast packets
pim6-multicast	IPv6 PIM multicast packets
pim6-unicast	IPv6 PIM unicast packets
portal	Portal packets
pvst	PVST packets
rip	RIP packets
ripng	RIPng packets
rrpp	RRPP packets
rsvp	RSVP packets
smart-link	SmartLink packets
snmp	SNMP packets
stp	STP packets
udp-helper	UDP helper packets
vrrp	VRRP packets
vrrp6	IPv6 VRRP packets

‌

Usage guidelines

In a traffic class with the logical OR operator, you can configure multiple if-match commands for any of the available match criteria.

When you configure a match criterion that can have multiple values in one if-match command, follow these restrictions and guidelines:

· You can specify up to eight values for any of the following match criteria in one if-match command:

¡ 802.1p priority.

¡ DSCP.

¡ IP precedence.

¡ VLAN ID.

· If a packet matches one of the specified values, it matches the if-match command.

· To delete a criterion that has multiple values, the specified values in the undo if-match command must be the same as those specified in the if-match command. The order of the values can be different.

When you configure ACL-based match criteria, follow these restrictions and guidelines:

· The ACL must already exist.

· The ACL is used for classification only and the permit/deny actions in ACL rules are ignored. Actions taken on matching packets are defined in traffic behaviors.

You can use both AND and OR operators to define the match relationships between the criteria for a class. For example, you can define relationships among three match criteria in traffic class classA as follows:

traffic classifier classB operator and

if-match criterion 1

if-match criterion 2

traffic classifier classA operator or

if-match criterion 3

For a QoS policy to match IPv6 packets, you must specify IPv6 packet match criteria (for example, configure a rule to match the IPv6 protocol type) in the corresponding traffic class.

Examples

# Define a match criterion for traffic class class1 to match the packets with a destination MAC address of 0050-ba27-bed3.

<Sysname> system-view

[Sysname] traffic classifier class1

[Sysname-classifier-class1] if-match destination-mac 0050-ba27-bed3

# Define a match criterion for traffic class class2 to match the packets with a source MAC address of 0050-ba27-bed2.

<Sysname> system-view

[Sysname] traffic classifier class2

[Sysname-classifier-class2] if-match source-mac 0050-ba27-bed2

# Define a match criterion for traffic class class1 to match the double-tagged packets with 802.1p priority 3 in the inner VLAN tag.

<Sysname> system-view

[Sysname] traffic classifier class1

[Sysname-classifier-class1] if-match customer-dot1p 3

# Define a match criterion for traffic class class1 to match the packets with 802.1p priority 5 in the outer VLAN tag.

<Sysname> system-view

[Sysname] traffic classifier class1

[Sysname-classifier-class1] if-match service-dot1p 5

# Define a match criterion for traffic class class1 to match advanced ACL 3101.

<Sysname> system-view

[Sysname] traffic classifier class1

[Sysname-classifier-class1] if-match acl 3101

# Define a match criterion for traffic class class1 to match the ACL named flow.

<Sysname> system-view

[Sysname] traffic classifier class1

[Sysname-classifier-class1] if-match acl name flow

# Define a match criterion for traffic class class1 to match advanced IPv6 ACL 3101.

<Sysname> system-view

[Sysname] traffic classifier class1

[Sysname-classifier-class1] if-match acl ipv6 3101

# Define a match criterion for traffic class class1 to match the IPv6 ACL named flow.

<Sysname> system-view

[Sysname] traffic classifier class1

[Sysname-classifier-class1] if-match acl ipv6 name flow

# Define a match criterion for traffic class class1 to match all packets.

<Sysname> system-view

[Sysname] traffic classifier class1

[Sysname-classifier-class1] if-match any

# Define a match criterion for traffic class class1 to match IP packets.

<Sysname> system-view

[Sysname] traffic classifier class1

[Sysname-classifier-class1] if-match protocol ip

traffic classifier

Use traffic classifier to create a traffic class and enter its view, or enter the view of an existing traffic class.

Use undo traffic classifier to delete a traffic class.

Syntax

traffic classifier classifier-name [ operator { and | or } ]

undo traffic classifier classifier-name

Default

No traffic classes exist.

Views

System view

Predefined user roles

network-admin

Parameters

classifier-name: Specifies a name for the traffic class, a case-sensitive string of 1 to 31 characters.

operator: Sets the operator to logic AND (the default) or OR for the traffic class.

and: Specifies the logic AND operator. The traffic class matches the packets that match all its criteria.

or: Specifies the logic OR operator. The traffic class matches the packets that match any of its criteria.

Examples

# Create a traffic class named class1.

<Sysname> system-view

[Sysname] traffic classifier class1

[Sysname-classifier-class1]

Related commands

display traffic classifier

Traffic behavior commands

accounting

Use accounting to configure a traffic accounting action in a traffic behavior.

Use undo accounting to restore the default.

Syntax

accounting [ byte | packet ]

undo accounting

Default

No traffic accounting action is configured.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

byte: Counts traffic in bytes.

packet: Counts traffic in packets.

Usage guidelines

If you execute the car command multiple times in the same traffic behavior, the most recent configuration takes effect.

If you do not specify the byte or packet keyword, the device counts traffic in packets and bytes.

Examples

# Configure a traffic accounting action in traffic behavior database to count traffic in bytes.

<Sysname> system-view

[Sysname] traffic behavior database

[Sysname-behavior-database] accounting byte

car

Use car to configure a CAR action in absolute value in a traffic behavior.

Use undo car to restore the default.

Syntax

car cir committed-information-rate [ cbs committed-burst-size [ ebs excess-burst-size ] ] [ green action | red action | yellow action ] *

car cir committed-information-rate [ cbs committed-burst-size ] pir peak-information-rate [ ebs excess-burst-size ] [ green action | red action | yellow action ] *

undo car

Default

No CAR action is configured.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

cir committed-information-rate: Specifies the committed information rate (CIR) in the range of 10 to 100000000, which must be a multiple of 10.

cbs committee-burst-size: Specifies the committed burst size (CBS) in bytes. The value range for committed-burst-size is 512 to 67092480, in increments of 512. The default value for this argument is the product of 62.5 and the CIR and must be an integral multiple of 512. When the product is not an integral multiple of 512, it is rounded up to the nearest integral multiple of 512 that is greater than the product. A default value greater than 67092480 is converted to 67092480.

ebs excess-burst-size: Specifies the excess burst size (EBS) in bytes. The value range for excess-burst-size is 0 to 67092480, in increments of 512. If the PIR is configured, the default EBS is the product of 62.5 and the PIR and must be an integral multiple of 512. When the product is not an integral multiple of 512, it is rounded up to the nearest integral multiple of 512. A default value greater than 67092480 is converted to 67092480.

pir peak-information-rate: Specifies the peak information rate (PIR) in the range of 10 to 100000000 kbps, in increments of 10. The PIR and CIR must be configured in the same measurement unit.

green action: Specifies the action to take on packets that conform to the CIR. The default setting is pass.

red action: Specifies the action to take on packets that conform to neither CIR nor PIR. The default setting is discard.

yellow action: Specifies the action to take on packets that conform to the PIR but not to the CIR. The default setting is pass.

action: Sets the action to take on the packet:

· discard: Drops the packet.

· pass: Permits the packet to pass through.

· remark-lp-pass new-local-precedence: Sets the local precedence value of the packet to new-local-precedence and permits the packet to pass through. The new-local-precedence argument is in the range of 0 to 7.

Usage guidelines

To use two rates for traffic policing, configure the car command with the pir peak-information-rate option. To use one rate for traffic policing, configure the car command without the pir peak-information-rate option.

If you execute the car command multiple times in the same traffic behavior, the most recent configuration takes effect.

Priority marking in this command is supported only in the inbound direction.

If the action to take on yellow packets is discard, the action to take on red packets cannot be pass or remark-lp-pass.

To count red packets, yellow packets, and green packets, also execute the accounting command in the traffic behavior.

Examples

# Configure a CAR action in traffic behavior database: Set the CIR to 300 kbps and CBS to 51200 bytes.

<Sysname> system-view

[Sysname] traffic behavior database

[Sysname-behavior-database] car cir 300 cbs 51200

display traffic behavior

Use display traffic behavior to display traffic behaviors.

Syntax

display traffic behavior user-defined [ behavior-name ] [ slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

user-defined: Specifies user-defined traffic behaviors.

behavior-name: Specifies a behavior by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a traffic behavior, this command displays all traffic behaviors.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays the traffic behaviors for the master device. ‌‌

Examples

# Display all user-defined traffic behaviors.

<Sysname> display traffic behavior user-defined

User-defined behavior information:

Behavior: 1 (ID 100)

Marking:

Remark dscp 3

Committed Access Rate:

CIR 120 (kbps), CBS 5120 (Bytes), EBS 512 (Bytes)

Green action : pass

Yellow action : pass

Red action : discard

Behavior: 2 (ID 101)

Accounting enable: Packet

Filter enable: Permit

Redirecting:

Redirect to the CPU

Behavior: 3 (ID 102)

-none-

Table 4 Command output

Field	Description
Behavior	Name and contents of a traffic behavior.
Marking	Information about priority marking.
Remark dscp	Action of setting the DSCP value for packets.
Committed Access Rate	Information about the CAR action.
Green action	Action to take on green packets.
Yellow action	Action to take on yellow packets.
Red action	Action to take on red packets.
Accounting enable	Class-based accounting action.
Filter enable	Traffic filtering action.
Redirecting	Information about traffic redirecting. For information about marking actions, see "redirect."

‌

filter

Use filter to configure a traffic filtering action in a traffic behavior.

Use undo filter to restore the default.

Syntax

filter { deny | permit }

undo filter

Default

No traffic filtering action is configured.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

deny: Drops packets.

permit: Transmits packets.

Usage guidelines

When the device processes packets, packets might be simultaneously affected by QoS policies, packet filtering, policy-based routing (PBR), and other features. These features invoke ACL resources in parallel for packet matching, but their processing priority differs. The precedence of different features depends on the device model. The action taken by the high-priority feature determines whether the packet is dropped.

The keywords in the command have different meanings:

· deny—If a packet matches a traffic class, it is directly dropped and will no longer be affected by actions from lower-priority features.

· permit—If a packet matches a traffic class, the QoS policy does not affect the packet. If the packet is processed by other lower-priority features, whether it is dropped will depend on the actions of those lower-priority features.

Examples

# Configure a traffic filtering action as deny in traffic behavior database.

<Sysname> system-view

[Sysname] traffic behavior database

[Sysname-behavior-database] filter deny

nest top-most

Use nest top-most to configure an outer VLAN tag adding action in a traffic behavior.

Use undo nest top-most to restore the default.

Syntax

nest top-most vlan vlan-id

undo nest top-most

Default

No outer VLAN tag adding action is configured.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

vlan-id vlan-id: Specifies the VLAN ID to be added in the outer VLAN tag, in the range of 1 to 4094.

Usage guidelines

If a QoS policy contains an outer VLAN tag adding action, apply it only to the incoming traffic of an interface.

If you execute the nest top-most command multiple times in the same traffic behavior, the most recent configuration takes effect.

Examples

# Configure traffic behavior b1 to add an outer VLAN tag with VLAN ID 123.

<Sysname> system-view

[Sysname] traffic behavior b1

[Sysname-behavior-b1] nest top-most vlan 123

redirect

Use redirect to configure a traffic redirecting action in a traffic behavior.

Use undo redirect to restore the default.

Syntax

redirect { cpu | interface interface-type interface-number | next-hop { ipv4-add1 [ track track-entry-number ] [ ipv4-add2 [ track track-entry-number ] ] | ipv6-add1 [ track track-entry-number ] [ ipv6-add2 [ track track-entry-number ] ] } [ fail-action { discard | forward } ] }

undo redirect { cpu | interface interface-type interface-number | next-hop }

Default

No traffic redirecting action is configured.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

cpu: Redirects traffic to the CPU.

interface interface-type interface-number: Redirects traffic to an interface specified by its type and number.

next-hop: Redirects traffic to a next hop. For successful traffic redirection, make sure the next hop IP address is reachable. If both primary and secondary next hop IP addresses are specified, make sure a minimum of one IP address is reachable. The redirection feature periodically looks up the routing table to verify the reachability of next hop IP addresses.

ipv4-add1: Specifies the primary next hop IPv4 address. If traffic fails to be redirected to this IPv4 address, the traffic is redirected to the secondary IPv4 address.

ipv4-add2: Specifies the secondary next hop IPv4 address.

ipv6-add1: Specifies the primary next hop IPv6 address. If traffic fails to be redirected to this IPv6 address, the traffic is redirected to the secondary IPv6 address.

ipv6-add2: Specifies the secondary next hop IPv6 address.

track track-entry-number: Specifies a track entry by its ID in the range of 1 to 1024. Different track entries can be specified for primary and secondary IP addresses. By specifying track entries, you can associate traffic redirection with detection modules, such as NQA and BFD (see High Availability Configuration Guide).

fail-action: Specifies the action to take on packets if the next hop IP address does not exist. Without this parameter configured, the device forwards packets if the next hop IP address does not exist.

discard: Discards packets.

forward: Forwards packets.

Usage guidelines

If you execute the redirect command multiple times in the same traffic behavior, the most recent configuration takes effect.

A traffic redirecting action takes effect only when the QoS policy is applied to the inbound direction.

For traffic redirecting to an interface, make sure the VLAN ID of the interface to which the QoS policy is applied is in the allowed VLAN list of the redirected-to interface. Otherwise, the redirected-to interface drops redirected packets.

Examples

# Configure redirecting traffic to GigabitEthernet 1/0/1 in traffic behavior database.

<Sysname> system-view

[Sysname] traffic behavior database

[Sysname-behavior-database] redirect interface gigabitethernet 1/0/1

Related commands

classifier behavior

qos policy

traffic behavior

remark customer-vlan-id

Use remark customer-vlan-id to configure a CVLAN marking action in a traffic behavior.

Use undo remark customer-vlan-id to restore the default.

Syntax

remark customer-vlan-id vlan-id

undo remark customer-vlan-id

Default

No CVLAN marking action is configured.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

vlan-id: Specifies a CVLAN ID in the range of 1 to 4094.

Usage guidelines

A CVLAN marking action in a QoS policy takes effect only when it is applied to the inbound direction.

Examples

# Configure traffic behavior b1 to mark matching packets with CVLAN 111.

<Sysname> system-view

[Sysname] traffic behavior b1

[Sysname-behavior-b1] remark customer-vlan-id 111

remark dot1p

Use remark dot1p to configure an 802.1p priority marking action in a traffic behavior.

Use undo remark dot1p to restore the default.

Syntax

remark dot1p dot1p-value

undo remark dot1p

Default

No 802.1p priority marking action is configured.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

dot1p-value: Specifies the 802.1p priority to be marked for packets, in the range of 0 to 7.

Usage guidelines

An 802.1p priority marking action is supported only in the inbound direction.

Examples

# Configure traffic behavior database to mark matching traffic with 802.1p 2.

<Sysname> system-view

[Sysname] traffic behavior database

[Sysname-behavior-database] remark dot1p 2

remark drop-precedence

Use remark drop-precedence to configure a drop priority marking action in a traffic behavior.

Use undo remark drop-precedence to restore the default.

Syntax

remark drop-precedence drop-precedence-value

undo remark drop-precedence

Default

No drop priority marking action is configured.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

drop-precedence-value: Specifies the drop priority to be marked for packets, in the range of 0 to 2.

Usage guidelines

A drop priority marking action takes effect only when the QoS policy is applied to the inbound direction.

If you execute the remark drop-precedence command multiple times in the same traffic behavior, the most recent configuration takes effect.

Examples

# Configure traffic behavior database to mark matching traffic with drop priority 2.

<Sysname> system-view

[Sysname] traffic behavior database

[Sysname-behavior-database] remark drop-precedence 2

remark dscp

Use remark dscp to configure a DSCP marking action in a traffic behavior.

Use undo remark dscp to restore the default.

Syntax

remark dscp dscp-value

undo remark dscp

Default

No DSCP marking action is configured.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

dscp-value: Specifies a DSCP value, which can be a number from 0 to 63 or a keyword in Table 5.

Table 5 DSCP keywords and values

Keyword	DSCP value (binary)	DSCP value (decimal)
af11	001010	10
af12	001100	12
af13	001110	14
af21	010010	18
af22	010100	20
af23	010110	22
af31	011010	26
af32	011100	28
af33	011110	30
af41	100010	34
af42	100100	36
af43	100110	38
cs1	001000	8
cs2	010000	16
cs3	011000	24
cs4	100000	32
cs5	101000	40
cs6	110000	48
cs7	111000	56
default	000000	0
ef	101110	46

Usage guidelines

A DSCP marking action in a QoS policy takes effect only when it is applied in the inbound direction.

Examples

# Configure traffic behavior database to mark matching traffic with DSCP 6.

<Sysname> system-view

[Sysname] traffic behavior database

[Sysname-behavior-database] remark dscp 6

remark ip-precedence

Use remark ip-precedence to configure an IP precedence marking action in a traffic behavior.

Use undo remark ip-precedence to restore the default.

Syntax

remark ip-precedence ip-precedence-value

undo remark ip-precedence

Default

No IP precedence marking action is configured.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

ip-precedence-value: Specifies the IP precedence value to be marked for packets, in the range of 0 to 7.

Examples

# Set the IP precedence to 6 for packets.

<Sysname> system-view

[Sysname] traffic behavior database

[Sysname-behavior-database] remark ip-precedence 6

remark local-precedence

Use remark local-precedence to configure a local precedence marking action in a traffic behavior.

Use undo remark local-precedence to restore the default.

Syntax

remark [ green | red | yellow ] local-precedence local-precedence-value

undo remark [ green | red | yellow ] local-precedence

Default

No local precedence marking action is configured.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

green: Specifies green packets.

red: Specifies red packets.

yellow: Specifies yellow packets.

local-precedence-value: Specifies the local precedence to be marked for packets, in the range of 0 to 15.

Usage guidelines

A local precedence marking action takes effect only when the QoS policy is applied to the inbound direction.

Examples

# Configure traffic behavior database to mark matching traffic with local precedence 2.

<Sysname> system-view

[Sysname] traffic behavior database

[Sysname-behavior-database] remark local-precedence 2

remark qos-local-id

Use remark qos-local-id to configure a local QoS ID marking action in a traffic behavior.

Use undo remark qos-local-id to restore the default.

Syntax

remark qos-local-id local-id-value

undo remark qos-local-id [ egress-active ]

Default

No local QoS ID marking action is configured.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

local-id-value: Specifies the local QoS ID to be marked for packets, in the range of 1 to 4095. If the egress-active keyword is specified, the value range is 1 to 128.

Usage guidelines

If you execute the remark qos-local-id command multiple times in the same traffic behavior, the most recent configuration takes effect.

Examples

# Configure the action of marking packets with local QoS ID 2.

<Sysname> system-view

[Sysname] traffic behavior database

[Sysname-behavior-database] remark qos-local-id 2

remark service-vlan-id

Use remark service-vlan-id to configure an SVLAN marking action in a traffic behavior.

Use undo remark service-vlan-id to restore the default.

Syntax

remark service-vlan-id vlan-id

undo remark service-vlan-id

Default

No SVLAN marking action is configured.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

vlan-id: Specifies an SVLAN ID in the range of 1 to 4094.

Usage guidelines

An SVLAN marking action in a QoS policy takes effect only when it is applied to the inbound direction.

Examples

# Configure traffic behavior b1 to mark matching packets with SVLAN 222.

<Sysname> system-view

[Sysname] traffic behavior b1

[Sysname-behavior-b1] remark service-vlan-id 222

remark source-mac

Use remark source-mac to configure a source MAC address marking action in a traffic behavior.

Use undo remark source-mac to restore the default.

Syntax

remark source-mac mac-address

undo remark source-mac

Default

No source MAC address marking action is configured.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

mac-address: Specifies the source MAC address to be marked for packets, in the format of H-H-H.

Examples

# Configure traffic behavior behavior1 to mark matching traffic with source MAC address 600b-038a-a395.

<Sysname> system-view

[Sysname] traffic behavior behavior1

[Sysname-behavior-behavior1] remark source-mac 600b-038a-a395

Related commands

traffic behavior

Use traffic behavior to create a traffic behavior and enter its view, or enter the view of an existing traffic behavior.

Use undo traffic behavior to delete a traffic behavior.

Syntax

traffic behavior behavior-name

undo traffic behavior behavior-name

Default

No traffic behaviors exist.

Views

System view

Predefined user roles

network-admin

Parameters

behavior-name: Specifies a name for the traffic behavior, a case-sensitive string of 1 to 31 characters.

Examples

# Create a traffic behavior named behavior1.

<Sysname> system-view

[Sysname] traffic behavior behavior1

[Sysname-behavior-behavior1]

Related commands

display traffic behavior

QoS policy commands

classifier behavior

Use classifier behavior to associate a traffic behavior with a traffic class in a QoS policy.

Use undo classifier to delete a class-behavior association from a QoS policy.

Syntax

classifier classifier-name behavior behavior-name [ insert-before before-classifier-name ]

undo classifier classifier-name

Default

No traffic behavior is associated with a traffic class.

Views

QoS policy view

Predefined user roles

network-admin

Parameters

classifier-name: Specifies a traffic class by its name, a case-sensitive string of 1 to 31 characters.

behavior-name: Specifies a traffic behavior by its name, a case-sensitive string of 1 to 31 characters.

insert-before before-classifier-name: Inserts the new traffic class before an existing traffic class in the QoS policy. The before-classifier-name argument specifies an existing traffic class by its name, a case-sensitive string of 1 to 31 characters. If you do not specify the insert-before before-classifier-name option, the new traffic class is placed at the end of the QoS policy.

Usage guidelines

A QoS policy can contain multiple class-behavior associations. The device matches a packet against the class-behavior associations in their configuration order. When a match is found, the device stops the match process and takes the actions in the matching class-behavior association.

A traffic class can be associated only with one traffic behavior in a QoS policy.

If the specified traffic class or traffic behavior does not exist, the system defines a null traffic class or traffic behavior.

Examples

# Associate traffic class database with traffic behavior test in QoS policy user1.

<Sysname> system-view

[Sysname] qos policy user1

[Sysname-qospolicy-user1] classifier database behavior test

# Associate traffic class database with traffic behavior test in QoS policy user1, and insert traffic class database before an existing traffic class named class-a.

<Sysname> system-view

[Sysname] qos policy user1

[Sysname-qospolicy-user1] classifier database behavior test insert-before class-a

Related commands

qos policy

control-plane

Use control-plane to enter control plane view.

Syntax

control-plane slot slot-number

Views

System view

Predefined user roles

network-admin

Parameters

slot slot-number: Specifies an IRF member device by its member ID. ‌‌

Examples

# ‌‌Enter the control plane view of slot 3.

<Sysname> system-view

[Sysname] control-plane slot 3

[Sysname-cp-slot3]

control-plane management

Use control-plane management to enter control-plane management view.

Syntax

control-plane management

Views

System view

Predefined user roles

network-admin

Usage guidelines

A QoS policy applied in control-plane management view takes effect on the packets sent from the management interface to the control plane.

Examples

# Enter control-plane management view.

<Sysname> system-view

[Sysname] control-plane management

[Sysname-cp-management]

display qos policy

Use display qos policy to display QoS policies.

NOTE:

The following parameters are not available on the S5130S-EI-G, S5100-D-G, or S5500-D-G switch series:

· ipv6-matching

· accounting

· mirroring

· remarking

· tcp-erspan

Syntax

display qos policy { user-defined [ ipv6-matching | accounting | mirroring | remarking | tcp-erspan ] [ policy-name [ classifier classifier-name ] ] [ slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

user-defined: Specifies user-defined QoS policies.

ipv6-matching: Specifies IPv6-matching QoS policies.

accounting: Specifies accounting-type QoS policies.

mirroring: Specifies mirroring-type QoS policies.

remarking: Specifies marking-type QoS policies.

tcp-erspan: Specifies TCP ERSPAN-type QoS policies.

policy-name: Specifies a QoS policy by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a QoS policy, this command displays all user-defined QoS policies.

classifier classifier-name: Specifies a traffic class by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a traffic class, this command displays all traffic classes.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays the QoS policies for the master device. ‌‌

Examples

# Display all user-defined QoS policies.

<Sysname> display qos policy user-defined

User-defined QoS policy information:

Policy: 1 (ID 100)

Classifier: 1 (ID 100)

Behavior: 1

Marking:

Remark dscp 3

Committed Access Rate:

CIR 120 (kbps), CBS 51200 (Bytes), EBS 512 (Bytes)

Green action : pass

Yellow action : pass

Red action : discard

Classifier: 2 (ID 101)

Behavior: 2

Accounting enable: Packet

Filter enable: Permit

Marking:

Remark dot1p 4

Classifier: 3 (ID 102)

Behavior: 3

-none-

# Display user-defined accounting-type QoS policies.

<Sysname> display qos policy user-defined accounting

User-defined QoS policy information:

Accounting policy: 1 (ID 100)

Classifier: 1 (ID 100)

Behavior: 1

Accounting enable: Packet

# Display user-defined marking-type QoS policies.

<Sysname> display qos policy user-defined remarking

User-defined QoS policy information:

Marking policy: 1 (ID 100)

Classifier: 1 (ID 100)

Behavior: 1

Marking:

Remark dscp 3

# Display user-defined TCP ERSPAN-type QoS policies.

<Sysname> display qos policy user-defined tcp-erspan

User-defined QoS policy information:

TCP ERSPAN policy: 1 (ID 100)

Classifier: 1 (ID 100)

Behavior: 1

Mirroring:

Mirror to the interface: GigabitEthernet1/0/1

Table 6 Command output

Field	Description
User-defined QoS policy information	Information about a user-defined QoS policy.
System-defined QoS policy information	Information about a system-defined QoS policy.

For the description of other fields, see Table 1 and Table 4.

display qos policy control-plane

Use display qos policy control-plane to display QoS policies applied to a control plane.

Syntax

display qos policy control-plane slot slot-number

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies an IRF member device by its member ID. ‌‌

Examples

# ‌‌Display the QoS policy applied to the control plane of slot 1.

<Sysname> display qos policy control-plane slot 1

Control plane slot 1

Direction: Inbound

Policy: 1

Classifier: 1

Operator: AND

Rule(s) :

If-match acl 2000

Behavior: 1

Marking:

Remark dscp 3

Committed Access Rate:

CIR 112 (kbps), CBS 51200 (Bytes), EBS 512 (Bytes)

Green action : pass

Yellow action : pass

Red action : discard

Green packets : 0 (Packets) 0 (Bytes)

Yellow packets: 0 (Packets) 0 (Bytes)

Red packets : 0 (Packets) 0 (Bytes)

Classifier: 2

Operator: AND

Rule(s) :

If-match protocol ipv6

Behavior: 2

Accounting enable:

0 (Packets)

Filter enable: Permit

Marking:

Remark dscp 3

Classifier: 3

Operator: AND

Rule(s) :

-none-

Behavior: 3

-none-

Table 7 Command output

Field	Description
Direction	Direction in which the QoS policy is applied.

For the description of other fields, see Table 1 and Table 4.

display qos policy control-plane management

Use display qos policy control-plane management to display the QoS policies applied in control-plane management view.

Syntax

display qos policy control-plane management

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display the QoS policy applied in control-plane management view.

<Sysname> display qos policy control-plane management

Control plane management

Direction: Inbound

Policy: a

Classifier: default-class

Matched : 0 (Packets) 0 (Bytes)

Operator: AND

Rule(s) :

If-match any

Behavior: be

-none-

Classifier: a

Matched : 3 (Packets) 180 (Bytes)

Operator: OR

Rule(s) :

If-match control-plane protocol arp

If-match control-plane protocol rip

If-match control-plane protocol-group critical

If-match acl 3001

If-match control-plane protocol bgp

If-match control-plane protocol bgp4+

If-match control-plane protocol ftp

If-match control-plane protocol http https icmp icmp6 ripng snmp

Behavior: a

Committed Access Rate:

CIR 128 (kbps), CBS 51200 (Bytes), EBS 0 (Bytes)

Green action : pass

Yellow action : pass

Red action : discard

Green packets : 3 (Packets) 180 (Bytes)

Yellow packets: 0 (Packets) 0 (Bytes)

Red packets : 0 (Packets) 0 (Bytes)

Table 8 Command output

Field	Description
Direction	Direction in which the QoS policy is applied.

For the description of other fields, see Table 1 and Table 4.

display qos policy control-plane management pre-defined

Use display qos policy control-plane management pre-defined to display the predefined QoS policy applied in control-plane management view.

Syntax

display qos policy control-plane management pre-defined

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display the predefined QoS policy applied in control-plane management view.

<Sysname> display qos policy control-plane management pre-defined

Pre-defined control plane policy management

Protocol Priority Bandwidth Group

Default N/A 100000 (bps) N/A

ARP N/A 128 (bps) normal

BGP N/A 256 (bps) critical

BGPv6 N/A 256 (bps) critical

HTTP N/A 512 (bps) management

HTTPS N/A 512 (bps) management

ICMP N/A 128 (bps) monitor

ICMPv6 N/A 128 (bps) monitor

OSPF Multicast N/A 256 (bps) critical

OSPF Unicast N/A 256 (bps) critical

OSPFv3 Multicast N/A 256 (bps) critical

OSFPv3 Unicast N/A 256 (bps) critical

RIP N/A 1024 (bps) critical

RIPng N/A 256 (bps) critical

SNMP N/A 512 (bps) management

SSH N/A 512 (bps) management

TELNET N/A 512 (bps) management

FTP N/A 512 (bps) management

TFTP N/A 512 (bps) management

Table 9 Command output

Field	Description
Pre-defined control plane policy management	Predefined QoS policy applied in control-plane management view.
Protocol	System-defined protocol packet type.
Group	Protocol group to which the protocol belongs.

display qos policy control-plane pre-defined

Use display qos policy control-plane pre-defined to display predefined control plane QoS policies.

Syntax

display qos policy control-plane pre-defined [ slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays predefined control plane QoS policies for all member devices. ‌‌

Examples

# ‌‌Display the predefined control plane QoS policy of slot 1.

<Sysname> display qos policy control-plane pre-defined slot 1

Pre-defined policy information slot 1

Protocol Priority Bandwidth Group

Default N/A 1000 (pps) N/A

IS-IS 18 1000 (pps) critical

VRRP 19 1000 (pps) important

OSPF Multicast 18 1000 (pps) critical

OSPF Unicast 18 1000 (pps) critical

IGMP 11 500 (pps) important

OSPFv3 Unicast 18 1000 (pps) critical

OSPFv3 Multicast 18 1000 (pps) critical

VRRPv6 19 1000 (pps) important

ARP 2 1000 (pps) normal

DHCP Snooping 10 300 (pps) redirect

DHCP 10 300 (pps) normal

802.1x 3 500 (pps) important

STP 17 300 (pps) critical

LACP 22 300 (pps) critical

MVRP 15 300 (pps) critical

BGP 16 1000 (pps) critical

ICMP 3 500 (pps) monitor

TTL Expires 5 300 (pps) monitor

IPOPTION 5 300 (pps) normal

BGPv6 16 1000 (pps) critical

Hop Limit Expires 5 300 (pps) monitor

IPOPTIONv6 5 300 (pps) normal

LLDP 14 300 (pps) important

DLDP 16 300 (pps) critical

TELNET 1 800 (pps) management

SSH 1 800 (pps) management

TACACS 1 800 (pps) management

RADIUS 1 800 (pps) management

HTTP 3 500 (pps) management

HTTPS 3 500 (pps) management

SNMP 4 800 (pps) management

ARP Snooping 2 1000 (pps) redirect

ICMPv6 3 300 (pps) monitor

DHCPv6 10 300 (pps) normal

BFD 21 1000 (pps) critical

Table 10 Command output

Field	Description
Default	Protocols other than those listed.
Group	Protocol group of the protocol.

For descriptions of other fields, see Table 3.

display qos policy control-plane rule-statistics

Use display qos policy control-plane rule-statistics to display statistics for the QoS policy applied to a control plane.

Syntax

display qos policy control-plane slot slot-number rule-statistics

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies an IRF member device by its member ID.Specifies the slot number of the device, which is fixed at 1. ‌‌

‌‌

Usage guidelines

This command displays traffic statistics for an ACL match criterion on a per-rule basis. To display the traffic statistics, you must execute the accounting command in the traffic behavior to configure a traffic accounting action.

Examples

# ‌‌Display statistics for the QoS policy applied to the control plane in slot 0.‌‌

<Sysname> display qos policy control-plane slot 0 rule-statistics

Control plane slot 0

Direction: Inbound, Policy: p1, Status: Succeed

Classifier: c1, Operator: AND, Behavior: b1, State: Succeed

Accounting: Enabled, Car: Enabled

----------------------------------------------------------------------------

if-match source-mac 0001-0001-0001

if-match local-precedence 1

----------------------------------------------------------------------------

if-match acl 3000

rule 0 permit ip source 1.1.1.1 0

Passed packets 500, Passed pps 5

Dropped packets 500, Dropped pps 5

Passed bytes 5000, Passed bps 50

Dropped bytes 5000, Dropped bps 50

----------------------------------------------------------------------------

if-match acl 3000

rule 5 permit ip destination 2.2.2.2 0

Passed packets 500, Passed pps 5

Dropped packets 500, Dropped pps 5

Passed bytes 5000, Passed bps 50

Dropped bytes 5000, Dropped bps 50

----------------------------------------------------------------------------

Table 11 Command output

Field	Description
Direction	Direction in which the QoS policy is applied.
Status	QoS policy application result: · Succeed—The QoS policy is applied successfully. · Failed—The QoS policy fails to be applied. The statistics cannot be displayed.
Operator	Logical relationship between match criteria. Options include: · AND—A packet is counted only if it matches all match criteria configured by using if-match commands in a traffic class. The logical relationship between ACL rules in an ACL match criterion configured by using an if-match acl command is OR. · OR—A packet is counted if it matches any one of the match criteria configured by using if-match commands in a traffic class.
State	State of the class-behavior association: · Succeed—The class-behavior association is normal. · Failed—The class-behavior association is abnormal. For example, the traffic class contains match criteria that cannot both take effect or the traffic behavior contains conflicting actions. If the class-behavior association is abnormal, the statistics cannot be displayed.
Accounting	Indicates whether a traffic accounting action is configured in the traffic behavior. If a traffic accounting action is not configured, the traffic statistics cannot be displayed.
Car	Indicates whether a traffic policing action is configured in the traffic behavior. If a traffic policing action is not configured, the traffic statistics cannot be displayed.
Passed packets	Total number of forwarded packets. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Passed bytes	Total number of forwarded bytes. This field is displayed only if the accounting byte command is executed in the traffic behavior.
Passed pps	Number of packets forwarded per second. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Passed bps	Number of bits forwarded per second. This field is displayed only if the accounting byte command is executed in the traffic behavior.
Dropped packets	Total number of dropped packets. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Dropped bytes	Total number of forwarded bytes. This field is displayed only if the accounting byte command is executed in the traffic behavior.
Dropped pps	Number of packets dropped per second. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Dropped bps	Number of bits dropped per second. This field is displayed only if the accounting byte command is executed in the traffic behavior.

Related commands

accounting

qos apply policy (control plane view)

display qos policy global

Use display qos policy global to display QoS policies applied globally.

NOTE:

The following parameters are not available on the S5130S-EI-G, S5100-D-G, or S5500-D-G switch series:

· ipv6-matching

· accounting

· mirroring

· remarking

· tcp-erspan

Syntax

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ipv6-matching: Specifies IPv6-matching QoS policies.

accounting: Specifies accounting-type QoS policies.

mirroring: Specifies mirroring-type QoS policies.

remarking: Specifies marking-type QoS policies.

tcp-erspan: Specifies TCP ERSPAN-type QoS policies.

inbound: Specifies the QoS policy applied in the inbound direction.

outbound: Specifies the QoS policy applied in the outbound direction.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays global QoS policies for the master device. ‌‌

Usage guidelines

If you do not specify the ipv6-matching, accounting, mirroring, remarking, or tcp-erspan keyword, this command displays information about generic QoS policies.

If you do not specify a direction, this command displays both inbound and outbound global QoS policies.

Examples

# Display generic QoS policies applied globally.

<Sysname> display qos policy global

Direction: Inbound

Policy: 1

Classifier: 1

Operator: AND

Rule(s) :

If-match acl 2000

Behavior: 1

Marking:

Remark dscp 3

Committed Access Rate:

CIR 120 (kbps), CBS 51200 (Bytes), EBS 512 (Bytes)

Green action : pass

Yellow action : pass

Red action : discard

Green packets : 0 (Packets) 0 (Bytes)

Yellow packets: 0 (Packets) 0 (Bytes)

Red packets : 0 (Packets) 0 (Bytes)

Classifier: 2

Operator: AND

Rule(s) :

If-match protocol ipv6

Behavior: 2

Accounting enable:

184057187 (Packets)

844575 (pps)

Filter enable: Permit

Marking:

Remark dscp 3

Classifier: 3

Operator: AND

Rule(s) :

-none-

Behavior: 3

-none-

Table 12 Command output

Field	Description
Direction	Direction in which the QoS policy is applied.
Policy	User-defined generic QoS policy name.
Green packets	Statistics about green packets.
Yellow packets	Statistics about yellow packets.
Red packets	Statistics about red packets.

For the description of other fields, see Table 1 and Table 4.

display qos policy global rule-statistics

Use display qos policy global rule-statistics to display statistics for QoS policies applied globally.

Syntax

‌

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ipv6-matching: Specifies the IPv6 matching-type QoS policy.

accounting: Specifies the accounting-type QoS policy.

mirroring: Specifies the mirroring-type QoS policy.

remarking: Specifies the marking-type QoS policy.

tcp-erspan: Specifies the TCP ERSPAN-type QoS policy.

inbound: Specifies the inbound direction.

outbound: Specifies the outbound direction.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays global QoS policy statistics for the master device. ‌‌

Usage guidelines

If you do not specify a direction, this command displays statistics for QoS policies applied in each direction.

Examples

# ‌‌Display statistics for the QoS policies applied globally in the inbound direction in slot 0.‌‌

<Sysname> display qos policy global slot 0 inbound rule-statistics

Slot 0

Direction: Inbound, Policy: p1, Status: Succeed

Classifier: c1, Operator: AND, Behavior: b1, State: Succeed

Accounting: Enabled, Car: Enabled

----------------------------------------------------------------------------

if-match source-mac 0001-0001-0001

if-match local-precedence 1

----------------------------------------------------------------------------

if-match acl 3000

rule 0 permit ip source 1.1.1.1 0

Passed packets 500, Passed pps 5

Dropped packets 500, Dropped pps 5

Passed bytes 5000, Passed bps 50

Dropped bytes 5000, Dropped bps 50

----------------------------------------------------------------------------

if-match acl 3000

rule 5 permit ip destination 2.2.2.2 0

Passed packets 500, Passed pps 5

Dropped packets 500, Dropped pps 5

Passed bytes 5000, Passed bps 50

Dropped bytes 5000, Dropped bps 50

----------------------------------------------------------------------------

Table 13 Command output

Field	Description
Direction	Direction in which the QoS policy is applied.
Status	QoS policy application result: · Succeed—The QoS policy is applied successfully. · Failed—The QoS policy fails to be applied. The statistics cannot be displayed.
Operator	Logical relationship between match criteria. Options include: · AND—A packet is counted only if it matches all match criteria configured by using if-match commands in a traffic class. The logical relationship between ACL rules in an ACL match criterion configured by using an if-match acl command is OR. · OR—A packet is counted if it matches any one of the match criteria configured by using if-match commands in a traffic class.
State	State of the class-behavior association: · Succeed—The class-behavior association is normal. · Failed—The class-behavior association is abnormal. For example, the traffic class contains match criteria that cannot both take effect or the traffic behavior contains conflicting actions. If the class-behavior association is abnormal, the statistics cannot be displayed.
Accounting	Indicates whether a traffic accounting action is configured in the traffic behavior. If a traffic accounting action is not configured, the traffic statistics cannot be displayed.
Car	Indicates whether a traffic policing action is configured in the traffic behavior. If a traffic policing action is not configured, the traffic statistics cannot be displayed.
Passed packets	Total number of forwarded packets. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Passed bytes	Total number of forwarded bytes. This field is displayed only if the accounting byte command is executed in the traffic behavior.
Passed pps	Number of packets forwarded per second. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Passed bps	Number of bits forwarded per second. This field is displayed only if the accounting byte command is executed in the traffic behavior.
Dropped packets	Total number of dropped packets. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Dropped bytes	Total number of forwarded bytes. This field is displayed only if the accounting byte command is executed in the traffic behavior.
Dropped pps	Number of packets dropped per second. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Dropped bps	Number of bits dropped per second. This field is displayed only if the accounting byte command is executed in the traffic behavior.

Related commands

accounting

qos apply policy global

display qos policy interface

Use display qos policy interface to display the QoS policies applied to interfaces.

NOTE:

The following parameters are not available on the S5130S-EI-G, S5100-D-G, or S5500-D-G switch series:

· ipv6-matching

· accounting

· mirroring

· remarking

· tcp-erspan

Syntax

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ipv6-matching: Specifies IPv6-matching QoS policies.

accounting: Specifies accounting-type QoS policies.

mirroring: Specifies mirroring-type QoS policies.

remarking: Specifies marking-type QoS policies.

tcp-erspan: Specifies TCP ERSPAN-type QoS policies.

interface-type interface-number: Specifies an interface by its type and number.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify an IRF member device, this command displays QoS policies on the master device. Only logical interfaces support this option. ‌‌

inbound: Specifies the QoS policy applied to incoming traffic.

outbound: Specifies the QoS policy applied to outgoing traffic.

Usage guidelines

If you do not specify the ipv6-matching, accounting, mirroring, remarking, or tcp-erspan keyword, this command displays generic QoS policies applied.

If you do not specify a direction, this command displays the QoS policy applied to incoming traffic and the QoS policy applied to outgoing traffic.

Examples

# Display the QoS policy applied to the incoming traffic of GigabitEthernet 1/0/1.

<Sysname> display qos policy interface gigabitethernet 1/0/1 inbound

Interface: GigabitEthernet1/0/1

Direction: Inbound

Policy: 1

Classifier: 1

Operator: AND

Rule(s) :

If-match acl 2000

Behavior: 1

Marking:

Remark dscp 3

Committed Access Rate:

CIR 120 (kbps), CBS 51200 (Bytes), EBS 512 (Bytes)

Green action : pass

Yellow action : pass

Red action : discard

Green packets : 0 (Packets) 0 (Bytes)

Yellow packets: 0 (Packets) 0 (Bytes)

Red packets : 0 (Packets) 0 (Bytes)

Classifier: 2

Operator: AND

Rule(s) :

If-match protocol ipv6

Behavior: 2

Accounting enable:

0 (Packets), 0 (Bytes)

0 (pps), 0 (bps)

Filter enable: Permit

Marking:

Remark dscp 3

Classifier: 3

Operator: AND

Rule(s) :

-none-

Behavior: 3

-none-

# Display the QoS policies applied to all interfaces.

<Sysname> display qos policy interface

Interface: GigabitEthernet1/0/1

Direction: Inbound

Policy: a

Classifier: a

Operator: AND

Rule(s) :

If-match any

Behavior: a

Mirroring:

Mirror to the interface: GigabitEthernet1/0/2

Committed Access Rate:

CIR 120 (kbps), CBS 51200 (Bytes), EBS 0 (Bytes)

Green action : pass

Yellow action : pass

Red action : discard

Green packets : 0 (Packets)

Red packets : 0 (Packets)

Interface: GigabitEthernet1/0/3

Direction: Inbound

Policy: b

Classifier: b

Operator: AND

Rule(s) :

If-match any

Behavior: b

Committed Access Rate:

CIR 120 (kbps), CBS 51200 (Bytes), EBS 0 (Bytes)

Green action : pass

Yellow action : pass

Red action : discard

Green packets : 0(Packets)

Red packets : 0 (Packets)

Interface: GigabitEthernet1/0/4

Direction: Inbound

Policy: a

Classifier: a

Operator: AND

Rule(s) :

If-match any

Behavior: a

Mirroring:

Mirror to the interface: GigabitEthernet1/0/5

Committed Access Rate:

CIR 120 (kbps), CBS 51200 (Bytes), EBS 0 (Bytes)

Green action : pass

Yellow action : pass

Red action : discard

Green packets : 0 (Packets)

Red packets : 0 (Packets)

Table 14 Command output

Field	Description
Direction	Direction in which the QoS policy is applied.
Green packets	‌ Traffic statistics for green packets.
Yellow packets	‌ Traffic statistics for yellow packets.
Red packets	‌ Traffic statistics for red packets.

For the description of other fields, see Table 1 and Table 4.

display qos policy interface rule-statistics

Use display qos policy interface rule-statistics to display statistics for QoS policies applied to interfaces.

Syntax

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ipv6-matching: Specifies the IPv6 matching-type QoS policy.

accounting: Specifies the accounting-type QoS policy.

mirroring: Specifies the mirroring-type QoS policy.

remarking: Specifies the marking-type QoS policy.

tcp-erspan: Specifies the TCP ERSPAN-type QoS policy.

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays statistics for QoS policies applied to each interface.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays interface-based QoS policy statistics for the master device. ‌‌

inbound: Specifies the inbound direction.

outbound: Specifies the outbound direction.

Usage guidelines

If you do not specify a direction, this command displays statistics for QoS policies applied in each direction.

Examples

# ‌‌Display statistics for the QoS policies applied to the inbound direction of each interface in slot 1.‌‌

<Sysname> display qos policy global slot 1 inbound rule-statistics

Slot 1

Interface: GigabitEthernet1/0/1

Direction: Inbound, Policy: p1, Status: Succeed

Classifier: c1, Operator: AND, Behavior: b1, State: Succeed

Accounting: Enabled, Car: Enabled

----------------------------------------------------------------------------

if-match source-mac 0001-0001-0001

if-match local-precedence 1

----------------------------------------------------------------------------

if-match acl 3000

rule 0 permit ip source 1.1.1.1 0

Passed packets 500, Passed pps 5

Dropped packets 500, Dropped pps 5

Passed bytes 5000, Passed bps 50

Dropped bytes 5000, Dropped bps 50

----------------------------------------------------------------------------

if-match acl 3000

rule 5 permit ip destination 2.2.2.2 0

Passed packets 500, Passed pps 5

Dropped packets 500, Dropped pps 5

Passed bytes 5000, Passed bps 50

Dropped bytes 5000, Dropped bps 50

----------------------------------------------------------------------------

Table 15 Command output

Field	Description
Direction	Direction in which the QoS policy is applied.
Status	QoS policy application result: · Succeed—The QoS policy is applied successfully. · Failed—The QoS policy fails to be applied. The statistics cannot be displayed.
Operator	Logical relationship between match criteria. Options include: · AND—A packet is counted only if it matches all match criteria configured by using if-match commands in a traffic class. The logical relationship between ACL rules in an ACL match criterion configured by using an if-match acl command is OR. · OR—A packet is counted if it matches any one of the match criteria configured by using if-match commands in a traffic class.
State	State of the class-behavior association: · Succeed—The class-behavior association is normal. · Failed—The class-behavior association is abnormal. For example, the traffic class contains match criteria that cannot both take effect or the traffic behavior contains conflicting actions. If the class-behavior association is abnormal, the statistics cannot be displayed.
Accounting	Indicates whether a traffic accounting action is configured in the traffic behavior. If a traffic accounting action is not configured, the traffic statistics cannot be displayed.
Car	Indicates whether a traffic policing action is configured in the traffic behavior. If a traffic policing action is not configured, the traffic statistics cannot be displayed.
Passed packets	Total number of forwarded packets. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Passed bytes	Total number of forwarded bytes. This field is displayed only if the accounting byte command is executed in the traffic behavior.
Passed pps	Number of packets forwarded per second. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Passed bps	Number of bits forwarded per second. This field is displayed only if the accounting byte command is executed in the traffic behavior.
Dropped packets	Total number of dropped packets. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Dropped bytes	Total number of forwarded bytes. This field is displayed only if the accounting byte command is executed in the traffic behavior.
Dropped pps	Number of packets dropped per second. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Dropped bps	Number of bits dropped per second. This field is displayed only if the accounting byte command is executed in the traffic behavior.

Related commands

accounting

qos apply policy (interface view)

display qos vlan-policy

Use display qos vlan-policy to display QoS policies applied to VLANs.

Syntax

display qos vlan-policy { name policy-name | vlan [ vlan-id ] } [ slot slot-number ] [ inbound | outbound ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

name policy-name: Specifies a QoS policy by its name, a case-sensitive string of 1 to 31 characters.

vlan vlan-id: Specifies a VLAN by its ID in the range of 1 to 4094.

inbound: Displays QoS policies applied to incoming traffic.

outbound: Displays QoS policies applied to outgoing traffic.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays QoS policies applied to VLANs for the master device. ‌‌

Usage guidelines

If you do not specify a direction, this command displays QoS policies applied to VLANs in both the inbound and outbound directions.

Examples

# Display QoS policies applied to VLAN 2.

<Sysname> display qos vlan-policy vlan 2

Vlan 2

Direction: Inbound

Policy: 1

Classifier: 1

Operator: AND

Rule(s) :

If-match acl 2000

Behavior: 1

Marking:

Remark dscp 3

Committed Access Rate:

CIR 120 (kbps), CBS 5120 (Bytes), EBS 512 (Bytes)

Green action : pass

Yellow action : pass

Red action : discard

Green packets : 0(Packets) 0(Bytes)

Yellow packets: 0(Packets) 0(Bytes)

Red packets : 0(Packets) 0(Bytes)

Classifier: 2

Operator: AND

Rule(s) :

If-match protocol ipv6

Behavior: 2

Accounting enable:

0 (Packets), 0 (Bytes)

0 (pps), 0 (bps)

Filter enable: Permit

Marking:

Remark dscp 3

Classifier: 3

Operator: AND

Rule(s) :

-none-

Behavior: 3

-none-

Table 16 Command output

Field	Description
Direction	Direction in which the QoS policy is applied.
Green packets	Statistics about green packets.
Yellow packets	Statistics about yellow packets.
Red packets	Statistics about red packets.

For the description of other fields, see Table 1 and Table 4.

display qos vlan-policy rule-statistics

Use display qos vlan-policy rule-statistics to display statistics for QoS policies applied to VLANs.

Syntax

display qos vlan-policy vlan [ vlan-id ] [ slot slot-number ] [ inbound | outbound ] rule-statistics

display qos vlan-policy vlan [ vlan-id ] [ chassis chassis-number slot slot-number ] [ inbound | outbound ] rule-statistics

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vlan vlan-id: Specifies a VLAN by its ID. The value range for the vlan-id argument is 1 4094.

inbound: Specifies the inbound direction.

outbound: Specifies the outbound direction.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays VLAN-based QoS policy statistics for the master device. ‌‌

Usage guidelines

If you do not specify a direction, this command displays statistics for QoS policies applied in each direction.

Examples

# ‌‌Display statistics for the QoS policy applied to the inbound direction of VLAN 10 in slot 1.‌‌

<Sysname> display qos vlan-policy vlan 10 slot 1 inbound rule-statistics

Slot 0

Vlan 10

Direction: Inbound, Policy: p1, Status: Succeed

Classifier: c1, Operator: AND, Behavior: b1, State: Succeed

Accounting: Enabled, Car: Enabled

----------------------------------------------------------------------------

if-match source-mac 0001-0001-0001

if-match local-precedence 1

----------------------------------------------------------------------------

if-match acl 3000

rule 0 permit ip source 1.1.1.1 0

Passed packets 500, Passed pps 5

Dropped packets 500, Dropped pps 5

Passed bytes 5000, Passed bps 50

Dropped bytes 5000, Dropped bps 50

----------------------------------------------------------------------------

if-match acl 3000

rule 5 permit ip destination 2.2.2.2 0

Passed packets 500, Passed pps 5

Dropped packets 500, Dropped pps 5

Passed bytes 5000, Passed bps 50

Dropped bytes 5000, Dropped bps 50

----------------------------------------------------------------------------

Table 17 Command output

Field	Description
Direction	Direction in which the QoS policy is applied.
Status	QoS policy application result: · Succeed—The QoS policy is applied successfully. · Failed—The QoS policy fails to be applied. The statistics cannot be displayed.
Operator	Logical relationship between match criteria. Options include: · AND—A packet is counted only if it matches all match criteria configured by using if-match commands in a traffic class. The logical relationship between ACL rules in an ACL match criterion configured by using an if-match acl command is OR. · OR—A packet is counted if it matches any one of the match criteria configured by using if-match commands in a traffic class.
State	State of the class-behavior association: · Succeed—The class-behavior association is normal. · Failed—The class-behavior association is abnormal. For example, the traffic class contains match criteria that cannot both take effect or the traffic behavior contains conflicting actions. If the class-behavior association is abnormal, the statistics cannot be displayed.
Accounting	Indicates whether a traffic accounting action is configured in the traffic behavior. If a traffic accounting action is not configured, the traffic statistics cannot be displayed.
Car	Indicates whether a traffic policing action is configured in the traffic behavior. If a traffic policing action is not configured, the traffic statistics cannot be displayed.
Passed packets	Total number of forwarded packets. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Passed bytes	Total number of forwarded bytes. This field is displayed only if the accounting byte command is executed in the traffic behavior.
Passed pps	Number of packets forwarded per second. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Passed bps	Number of bits forwarded per second. This field is displayed only if the accounting byte command is executed in the traffic behavior.
Dropped packets	Total number of dropped packets. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Dropped bytes	Total number of forwarded bytes. This field is displayed only if the accounting byte command is executed in the traffic behavior.
Dropped pps	Number of packets dropped per second. This field is displayed only if the accounting packet command is executed in the traffic behavior.
Dropped bps	Number of bits dropped per second. This field is displayed only if the accounting byte command is executed in the traffic behavior.

Related commands

accounting

qos vlan-policy

qos apply policy (interface view, control plane view, control-plane management view)

Use qos apply policy to apply a QoS policy to a control plane, interface, or in control-plane management view.

Use undo qos apply policy to remove an applied QoS policy.

NOTE:

The following parameters are not available on the S5130S-EI-G, S5100-D-G, or S5500-D-G switch series:

· ipv6-matching

· accounting

· mirroring

· remarking

· tcp-erspan

Syntax

qos apply [ ipv6-matching | accounting | mirroring | remarking | tcp-erspan ] policy policy-name { inbound | outbound } [ longest-match ]

undo qos apply [ ipv6-matching | accounting | mirroring | remarking | tcp-erspan ] policy policy-name { inbound | outbound }

Default

No QoS policy is applied.

Views

Control plane view/control-plane management view

Interface view

Predefined user roles

network-admin

Parameters

ipv6-matching: Specifies an IPv6-matching QoS policy. This keyword is supported only in interface view or Ethernet service instance view.

accounting: Specifies an accounting-type QoS policy. This keyword is supported only in interface view or Ethernet service instance view.

mirroring: Specifies a mirroring-type QoS policy. This keyword is supported only in interface view or Ethernet service instance view.

remarking: Specifies a marking-type QoS policy. This keyword is supported only in interface view or Ethernet service instance view.

tcp-erspan: Specifies a TCP ERSPAN-type QoS policy. This keyword is supported only in interface view.

policy-name: Specifies a QoS policy by its name, a case-sensitive string of 1 to 31 characters.

inbound: Applies the QoS policy to incoming traffic.

outbound: Applies the QoS policy to outgoing traffic. This keyword is not supported in control plane view or control-plane management view.

longest-match: First matches the traffic class with a source or destination IP address with the longest mask and takes the actions in the associated traffic behavior if a match is found.

If you do not specify the longest-match keyword, the system matches traffic against traffic classes in the order class-behavior associations are configured. When the traffic matches a traffic class, the matching process stops, and the actions in the associated traffic behavior are taken on the matching traffic.

If you specify the longest-match keyword, the system first matches the traffic class with a source or destination address with the longest mask and takes the actions in the associated traffic behavior. Suppose three class-behavior associations are configured in a QoS policy. ACL 3001 in the traffic class of the first class-behavior association is not configured with a source or destination address. ACL 3002 in the traffic class of the second class-behavior association is configured with destination address 10.10.10.0/24. ACL 3003 in the traffic class of the third class-behavior association is configured with destination address 10.10.10.10/32. The match order of the three class-behavior associations is the third class-behavior association, the second class-behavior association, the first class-behavior association. If both source and destination addresses exist in ACLs of different traffic classes, the system matches destination addresses before matching source addresses.

A maximum of six QoS policies (one for each type) can be applied to one direction of an interface. Different actions can be taken on the same traffic class if QoS policies of different types are applied to an interface.

Examples

# Apply QoS policy TEST1 to the outgoing traffic of GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos apply policy TEST1 outbound

# Apply accounting-type QoS policy TEST2 to the outgoing traffic of GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos apply accounting policy TEST2 outbound

# Apply mirroring-type QoS policy TEST3 to the outgoing traffic of GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos apply mirroring policy TEST3 outbound

# Apply marking-type QoS policy TEST4 to the outgoing traffic of GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos apply remarking policy TEST4 outbound

# Apply TCP ERSPAN-type QoS policy TEST4 to the outgoing traffic of GigabitEthernet 1/0/1.

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos apply tcp-erspan policy TEST4 outbound

# Apply QoS policy TEST5 to the incoming traffic of the control plane of slot 3.

<Sysname> system-view

[Sysname] control-plane slot 3

[Sysname-cp-slot3] qos apply policy TEST5 inbound

# Apply generic QoS policy TEST6 to the incoming traffic of the management interface control plane.

<Sysname> system-view

[Sysname] control-plane management

[Sysname-cp-management] qos apply policy TEST6 inbound

qos apply policy global

Use qos apply policy global to apply a QoS policy globally.

Use undo qos apply policy global to remove a globally applied QoS policy.

NOTE:

The following parameters are not available on the S5130S-EI-G, S5100-D-G, or S5500-D-G switch series:

· ipv6-matching

· accounting

· mirroring

· remarking

· tcp-erspan

Syntax

qos apply [ ipv6-matching | accounting | mirroring | remarking | tcp-erspan ] policy policy-name global { inbound | outbound } [ longest-match ]

undo qos apply [ ipv6-matching | accounting | mirroring | remarking | tcp-erspan ] policy policy-name global { inbound | outbound }

Default

No QoS policy is applied globally.

Views

System view

Predefined user roles

network-admin

Parameters

ipv6-matching: Specifies an IPv6-matching QoS policy.

accounting: Specifies an accounting-type QoS policy.

mirroring: Specifies a mirroring-type QoS policy.

remarking: Specifies a marking-type QoS policy.

tcp-erspan: Specifies a TCP ERSPAN-type QoS policy.

policy-name: Specifies a QoS policy by its name, a case-sensitive string of 1 to 31 characters.

inbound: Applies the QoS policy to the incoming packets on all interfaces.

outbound: Applies the QoS policy to the outgoing packets on all interfaces.

longest-match: First matches the traffic class with a source or destination IP address with the longest mask and takes the actions in the associated traffic behavior if a match is found.

Usage guidelines

A global QoS policy takes effect on all incoming or outgoing traffic depending on the direction in which the QoS policy is applied.

A maximum of six QoS policies (one generic, one IPv6-matching, one accounting-type, one mirroring-type, one marking-type, and one TCP ERSPAN-type) can be applied to one direction globally.

If both source and destination addresses exist in ACLs of different traffic classes, the system matches destination addresses before matching source addresses.

Examples

# Globally apply QoS policy user1 to the incoming traffic.

<Sysname> system-view

[Sysname] qos apply policy user1 global inbound

qos policy

Use qos policy to create a QoS policy and enter its view, or enter the view of an existing QoS policy.

Use undo qos policy to delete a QoS policy.

NOTE:

The following parameters are not available on the S5130S-EI-G, S5100-D-G, or S5500-D-G switch series:

· ipv6-matching

· accounting

· mirroring

· remarking

· tcp-erspan

Syntax

qos [ ipv6-matching | accounting | mirroring | remarking | tcp-erspan ] policy policy-name

undo qos [ ipv6-matching | accounting | mirroring | remarking | tcp-erspan ] policy policy-name

Default

No QoS policies exist.

Views

System view

Predefined user roles

network-admin

Parameters

ipv6-matching: Identifies the QoS policy as an IPv6-matching QoS policy.

accounting: Identifies the QoS policy as an accounting-type QoS policy.

mirroring: Identifies the QoS policy as a mirroring-type QoS policy.

remarking: Identifies the QoS policy as a marking-type QoS policy.

tcp-erspan: Identifies the QoS policy as a TCP ERSPAN QoS policy.

policy-name: Specifies a name for the QoS policy, a case-sensitive string of 1 to 31 characters.

Usage guidelines

An IPv6-matching QoS policy is used for traffic classes containing IPv6 ACL match criteria. Other QoS policy types do not distinguish between IPv4 and IPv6.

In some scenarios, you need to apply a QoS policy for matching IPv4 packets and a QoS policy for matching IPv6 packets to the same direction of the same object. In this case, you use a generic QoS policy for matching IPv4 packets and an IPv6-matching QoS policy.

To delete a QoS policy that has been applied to an object, you must first remove the QoS policy from the object.

Examples

# Create a QoS policy named user1.

<Sysname> system-view

[Sysname] qos policy user1

[Sysname-qospolicy-user1]

Related commands

classifier behavior

qos apply policy

qos apply policy global

qos vlan-policy

Use qos vlan-policy to apply a QoS policy to the specified VLANs.

Use undo qos vlan-policy to remove a QoS policy from the specified VLANs.

NOTE:

The longest-match parameter is not available on the S5130S-EI-G, S5100-D-G, or S5500-D-G switch series.

Syntax

qos vlan-policy policy-name vlan vlan-id-list { inbound | outbound } [ longest-match ]

undo qos vlan-policy policy-name vlan vlan-id-list { inbound | outbound }

Default

No QoS policy is applied to a VLAN.

Views

System view

Predefined user roles

network-admin

Parameters

policy-name: Specifies a QoS policy by its name, a case-sensitive string of 1 to 31 characters.

vlan vlan-id-list: Specifies a space-separated list of up to eight VLAN IDs or a VLAN ID range in the form of vlan-id1 to vlan-id2. The value for vlan-id2 must be greater than or equal to the value for vlan-id1. The value range for the vlan-id argument is 1 to 4094.

inbound: Applies the QoS policy to incoming packets.

outbound: Applies the QoS policy to outgoing packets.

longest-match: First matches the traffic class with a source or destination IP address with the longest mask and takes the actions in the associated traffic behavior if a match is found.

Examples

# Apply QoS policy test to the incoming traffic of VLAN 200, VLAN 300, VLAN 400, and VLAN 500.

<Sysname> system-view

[Sysname] qos vlan-policy test vlan 200 300 400 500 inbound

reset qos policy control-plane

Use reset qos policy control-plane to clear the statistics of the QoS policy applied to a control plane.

Syntax

reset qos policy control-plane slot slot-number

Views

User view

Predefined user roles

network-admin

Parameters

slot slot-number: Specifies an IRF member device by its member ID. ‌‌

Examples

# ‌‌Clear the statistics of the QoS policy applied to the control plane of slot 1.

<Sysname> reset qos policy control-plane slot 1

reset qos policy control-plane management

Use reset qos policy control-plane management to clear the statistics of the QoS policy applied in control-plane management view.

Syntax

reset qos policy control-plane management

Views

User view

Predefined user roles

network-admin

Examples

# Clear the statistics of the QoS policy applied in control-plane management view.

<Sysname> reset qos policy control-plane management

reset qos policy global

Use reset qos policy global to clear statistics for QoS policies applied globally.

NOTE:

The following parameters are not available on the S5130S-EI-G, S5100-D-G, or S5500-D-G switch series:

· ipv6-matching

· accounting

· mirroring

· remarking

· tcp-erspan

Syntax

Views

User view

Predefined user roles

network-admin

Parameters

ipv6-matching: Specifies IPv6-matching QoS policies.

accounting: Specifies accounting-type QoS policies.

mirroring: Specifies mirroring-type QoS policies.

remarking: Specifies marking-type QoS policies.

tcp-erspan: Specifies TCP ERSPAN-type QoS policies.

inbound: Specifies the QoS policy applied to the inbound direction globally.

outbound: Specifies the QoS policy applied to the outbound direction globally.

Usage guidelines

If you do not specify a direction, this command clears statistics for the global QoS policies in both directions.

If you do not specify the ipv6-matching, accounting, mirroring, remarking, or tcp-erspan keyword, this command clears statistics for generic QoS policies.

Examples

# Clear statistics for the QoS policy applied to the inbound direction globally.

<Sysname> reset qos policy global inbound

reset qos vlan-policy

Use reset qos vlan-policy to clear the statistics for QoS policies applied to VLANs.

Syntax

reset qos vlan-policy [ vlan vlan-id ] [ inbound | outbound ]

Views

User view

Predefined user roles

network-admin

Parameters

vlan vlan-id: Specifies a VLAN ID in the range of 1 to 4094.

inbound: Specifies the QoS policy applied to incoming traffic.

outbound: Specifies the QoS policy applied to outgoing traffic.

Usage guidelines

If you do not specify a direction, this command clears the statistics of the QoS policies in both directions of the VLAN.

Examples

# Clear the statistics of QoS policies applied to VLAN 2.

<Sysname> reset qos vlan-policy vlan 2

QoS SNMP notification commands

snmp-agent trap enable qos

Use snmp-agent trap enable qos to enable SNMP notifications for QoS.

Use undo snmp-agent trap enable qos to disable SNMP notifications for QoS.

Syntax

snmp-agent trap enable qos

undo snmp-agent trap enable qos

Default

SNMP notifications are disabled for QoS.

Views

System view

Predefined user roles

network-admin

Usage guidelines

Execute this command to report critical QoS events by sending SNMP notifications.

For QoS notifications to be sent correctly, you must also configure SNMP on the device. For more information about SNMP configuration, see the network management and monitoring configuration guide for the device.

Examples

# Enable SNMP notifications for QoS.

<Sysname> system-view

[Sysname] snmp-agent trap enable qos

Priority mapping commands

Priority map commands

display qos map-table

Use display qos map-table to display the configuration of priority maps.

Syntax

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

The device provides the following types of priority map.

Table 18 Priority maps

Priority mapping	Description
dot1p-dp	802.1p-drop priority map.
dot1p-lp	802.1p-local priority map.
dscp-dp	DSCP-drop priority map.
dscp-lp	DSCP-local priority map.
dscp-dscp	DSCP-DSCP priority map.
exp-lp	EXP-local priority map.
lp-exp	Local-EXP priority map.

‌

Usage guidelines

If you do not specify a priority map, this command displays the configuration of all priority maps.

Examples

# Display the configuration of the 802.1p-local priority map.

<Sysname> display qos map-table dot1p-lp

MAP-TABLE NAME: dot1p-lp TYPE: pre-define

IMPORT : EXPORT

0 : 2

1 : 0

2 : 1

3 : 3

4 : 4

5 : 5

6 : 6

7 : 7

Table 19 Command output

Field	Description
MAP-TABLE NAME	Name of the priority map.
TYPE	Type of the priority map.
IMPORT	Input values of the priority map.
EXPORT	Output values of the priority map.

import

Use import to configure mappings for a priority map.

Use undo import to restore the specified or all mappings to the default for a priority map.

Syntax

import import-value-list export export-value

undo import { import-value-list | all }

Default

The default priority maps are used. For more information, see ACL and QoS Configuration Guide.

Views

Priority map view

Predefined user roles

network-admin

Parameters

import-value-list: Specifies a list of input values.

export-value: Specifies the output value.

all: Restores all mappings in the priority map to the default.

Examples

# Configure the 802.1p-local priority map to map 802.1p priority values 4 and 5 to local priority 1.

<Sysname> system-view

[Sysname] qos map-table dot1p-lp

[Sysname-maptbl-dot1p-lp] import 4 5 export 1

Related commands

display qos map-table

qos map-table

Use qos map-table to enter the specified priority map view.

Syntax

qos map-table { dot1p-dp | dot1p-lp | dscp-dp | dscp-dscp | dscp-lp | exp-lp | lp-exp }

Views

System view

Predefined user roles

network-admin

Parameters

For the description of keywords, see Table 18.

Examples

# Enter 802.1p-local priority map view.

<Sysname> system-view

[Sysname] qos map-table dot1p-lp

[Sysname-maptbl-dot1p-lp]

Related commands

display qos map-table

import

Priority trust mode commands

display qos trust interface

Use display qos trust interface to display the priority trust mode and port priorities of an interface.

Syntax

display qos trust interface [ interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays the priority trust mode and port priorities of all interfaces.

Examples

# Display the priority trust mode and port priority of GigabitEthernet 1/0/1.

<Sysname> display qos trust interface gigabitethernet 1/0/1

Interface: GigabitEthernet1/0/1

Port priority information

Port priority: 4

Port dscp priority: -

Port priority trust type: dscp

Table 20 Command output

Field	Description
Interface	Interface type and interface number.
Port priority	Port priority set for the interface.
Port dscp priority	DSCP value rewritten for packets. If you have not rewritten the DSCP value of packets, this field displays a hyphen (-).
Port priority trust type	Priority trust mode on the interface: · dot1p—Uses the 802.1p priority of received packets for mapping. · dscp—Uses the DSCP precedence of received IP packets for mapping.

qos trust (interface view)

Use qos trust to configure the priority trust mode for an interface.

Use undo qos trust to restore the default.

Syntax

qos trust { dot1p | dscp }

undo qos trust

Default

An interface does not trust packet priorities.

Views

Interface view

Predefined user roles

network-admin

Parameters

dot1p: Uses the 802.1p priority in incoming packets for priority mapping.

dscp: Uses the DSCP value in incoming packets for priority mapping.

Examples

# Set the priority trust mode to 802.1p priority on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos trust dot1p

Related commands

display qos trust interface

Port priority commands

qos priority

Use qos priority to change the port priority of an interface.

Use undo qos priority to restore the default.

Syntax

qos priority priority-value

undo qos priority

Default

The port priority is 0.

Views

Layer 2/Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

priority-value: Specifies a port priority value in the range of 0 to 7.

Examples

# Set the port priority of GigabitEthernet 1/0/1 to 2.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos priority 2

Related commands

display qos trust interface

GTS, and rate limit commands

GTS commands

display qos gts interface

Use display qos gts interface to display the GTS configuration for interfaces.

Syntax

display qos gts interface [ interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays the GTS configuration for all interfaces.

Examples

# Display the GTS configuration for all interfaces.

<Sysname> display qos gts interface

Interface: GigabitEthernet1/0/1

Rule: If-match queue 1

CIR 10 (kbps), CBS 1024 (Bytes)

Table 21 Command output

Field	Description
Interface	Interface name, including the interface type and interface number.
Rule	Match criteria.
CIR	CIR in kbps.
CBS	CBS in bytes.

qos gts

Use qos gts to set GTS parameters on an interface.

Use undo qos gts to delete the GTS configuration on an interface.

Syntax

qos gts queue queue-id cir committed-information-rate [ cbs committed-burst-size ]

undo qos gts queue queue-id

Default

No GTS parameters are configured.

Views

Layer 2/Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

queue queue-id: Shapes the packets in a queue specified by its ID. The value range for queue-id is 0 to 7.

cir committed-information-rate: Specifies the CIR in kbps. The value range for committed-information-rate is 10 to 10000000 for 10-GE interfaces, 10 to 25000000 for 25-Gbps interfaces, and 8 to 100000000 for 100-GE interfaces. This value must be a multiple of 10.

cbs committed-burst-size: Specifies the CBS in bytes. The value range for committed-burst-size is 512 to 67092480, in increments of 512. The default value for this argument is the product of 62.5 and the CIR and must be a multiple of 512. When the product is not a multiple of 512, it is rounded up to the nearest integral multiple of 512 that is greater than the product. A default value greater than 256000000 is converted to 256000000.

Examples

# Shape the packets in queue 1 on GigabitEthernet 1/0/1. The GTS parameters are as follows:

· The CIR is 260 kbps.

· The CBS is 51200 bytes.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos gts queue 1 cir 260 cbs 51200

Rate limit commands

display qos lr interface

Use display qos lr interface to display the rate limit configuration for interfaces.

Syntax

display qos lr interface [ interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays the rate limit configuration for all interfaces.

Examples

# Display the rate limit configuration for all interfaces.

<Sysname> display qos lr interface

Interface: GigabitEthernet1/0/1

Direction: Outbound

CIR 2000 (kbps), CBS 20480 (Bytes)

Table 22 Command output

Field	Description
Interface	Interface name, including the interface type and interface number.
Direction	Direction in which the rate limit configuration is applied.
CIR	CIR in kbps.
CBS	CBS in bytes.

qos lr

Use qos lr to configure rate limiting on an interface.

Use undo qos lr to delete the rate limit configuration on an interface.

Syntax

qos lr { inbound | outbound } cir committed-information-rate [ cbs committed-burst-size ]

undo qos lr outbound

Default

No rate limit is configured.

Views

Layer 2/Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

inbound: Limits the rate of incoming packets.

outbound: Limits the rate of outgoing packets.

cir committed-information-rate: Specifies the CIR in kbps. The committed-information-rate argument has the following value ranges: 10 to 10000000 for 10-GE interfaces, 10 to 25000000 for 25-GE interfaces, 10 to 100000000 for 100-GE interfaces. The specified value must be a multiple of 10.

cbs committee-burst-size: Specifies the committed burst size (CBS) in bytes. The value range for committed-burst-size is 512 to 8355840, in increments of 512. The default value for this argument is the product of 62.5 and the CIR and must be an integral multiple of 512. When the product is not an integral multiple of 512, it is rounded up to the nearest integral multiple of 512 that is greater than the product. A default value greater than 8355840 is converted to 8355840.

Examples

# Limit the rate of outgoing packets on GigabitEthernet 1/0/1, with CIR 260 kbps and CBS 51200 bytes.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos lr outbound cir 260 cbs 51200

Congestion management commands

Common commands

display qos queue interface

Use display qos queue interface to display the queuing information for interfaces.

Syntax

display qos queue interface [ interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays the queuing information for all interfaces.

Examples

# Display the queuing information for all interfaces.

<Sysname> display qos queue interface

Interface: GigabitEthernet1/0/1

Output queue: Strict Priority queuing

Interface: GigabitEthernet1/0/2

Output queue: Strict Priority queuing

…

Table 23 Command output

Field	Description
Interface	Interface name, including the interface type and interface number.
Output queue	Type of the current output queue.

SP commands

display qos queue sp interface

Use display qos queue sp interface to display the SP queuing configuration of an interface.

Syntax

display qos queue sp interface [ interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays the SP queuing configuration of all interfaces.

Examples

# Display the SP queuing configuration of GigabitEthernet 1/0/1.

<Sysname> display qos queue sp interface gigabitethernet 1/0/1

Interface: GigabitEthernet1/0/1

Output queue: Strict Priority queuing

Table 24 Command output

Field	Description
Interface	Interface type and interface number.
Output queue	Type of the current output queue.

qos sp (interface view)

Use qos sp to enable SP queuing on an interface.

Use undo qos sp to restore the default.

Syntax

qos sp

undo qos sp

Default

An interface uses SP queuing.

Views

Interface view

Predefined user roles

network-admin

Examples

# Enable SP queuing on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos sp

Related commands

display qos queue sp interface

WRR commands

display qos queue wrr interface

Use display qos queue wrr interface to display the WRR queuing configuration of an interface.

Syntax

display qos queue wrr interface [ interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays the WRR queuing configuration of all interfaces.

Examples

# Display the WRR queuing configuration of GigabitEthernet 1/0/1.

<Sysname> display qos queue wrr interface gigabitethernet 1/0/1

Interface: GigabitEthernet1/0/1

Output queue: Weighted Round Robin queuing

Queue ID Queue name Group Weight

---------------------------------------------------

0 be 1 1

1 af1 1 2

2 af2 1 3

3 af3 1 4

4 af4 1 5

5 ef 1 9

6 cs6 1 13

7 cs7 1 15

Table 25 Command output

Field	Description
Interface	Interface type and interface number.
Output queue	Type of the current output queue.
Group	ID of the group a queue is assigned to.
Weight	Packet-count queue scheduling weight of a queue. N/A is displayed for a queue that uses the SP scheduling algorithm.
Byte count	Byte-count scheduling weight of a queue. N/A is displayed for a queue that uses the SP scheduling algorithm.

‌

qos wrr (interface view)

Use qos wrr to enable WRR queuing on an interface.

Use undo qos wrr to restore the default.

Syntax

qos wrr { byte-count | weight }

undo qos wrr { byte-count | weight }

Default

An interface uses SP queuing.

Views

Interface view

Predefined user roles

network-admin

Parameters

byte-count: Allocates bandwidth to queues in bytes.

weight: Allocates bandwidth to queues in packets.

Usage guidelines

You must use the qos wrr command to enable WRR queuing before you can configure WRR queuing parameters for a queue on an interface.

Examples

# Enable packet-count WRR queuing on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos wrr weight

# Enable byte-count WRR queuing on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos wrr byte-count

Related commands

display qos queue wrr interface

qos wrr { byte-count | weight }

Use qos wrr { byte-count | weight } to configure the WRR queuing parameters for a queue on an interface.

Use undo qos wrr to restore the default.

Syntax

qos wrr queue-id group { 1 | 2 } { byte-count | weight } schedule-value

undo qos wrr queue-id

Default

All queues on a WRR-enabled interface are in WRR group 1, and queues 0 through 7 have a weight of 1, 2, 3, 4, 5, 9, 13, and 15, respectively.

Views

Layer 2/Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

queue-id: Specifies a queue by its ID. The value range for this argument is 0 to 7 or keywords in Table 26.

Table 26 The number-keyword map for the queue-id argument

Number	Keyword
0	be
1	af1
2	af2
3	af3
4	af4
5	ef
6	cs6
7	cs7

group { 1 | 2 }: Specifies WRR group 1 or 2. If you do not specify a group, group 1 applies. Group 1 has higher scheduling priority than group 2. Queues in group 2 are serviced only when all queues in group 1 are empty.

byte-count: Allocates bandwidth to queues in bytes.

weight: Allocates bandwidth to queues in packets.

schedule-value: Specifies a scheduling weight. The value range for this argument is 1 to 127.

Usage guidelines

You must use the qos wrr command to enable WRR queuing before you can configure WRR queuing parameters for a queue on an interface.

Examples

# Enable byte-count WRR queuing on GigabitEthernet 1/0/1, assign queue 0 to WRR group 1, and specify scheduling weight 10 for queue 0.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos wrr byte-count

[Sysname-GigabitEthernet1/0/1] qos wrr 0 group 1 byte-count 10

Related commands

display qos queue wrr interface

qos wrr

qos wrr group sp

Use qos wrr group sp to assign a queue to the SP group.

Use undo qos wrr group sp to remove a queue from the SP group.

Syntax

qos wrr queue-id group sp

undo qos wrr queue-id

Default

All queues on a WRR-enabled interface are in WRR group 1.

Views

Layer 2/Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

queue-id: Specifies a queue by its ID. The value range for this argument is 0 to 7 or keywords in Table 26.

Usage guidelines

This command is available only on a WRR-enabled interface. Queues in the SP group are scheduled with SP. The SP group has higher scheduling priority than the WRR groups.

You must use the qos wrr command to enable WRR queuing before you can configure this command on an interface.

Examples

# Enable WRR queuing on GigabitEthernet 1/0/1, and assign queue 0 to the SP group.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos wrr weight

[Sysname-GigabitEthernet1/0/1] qos wrr 0 group sp

Related commands

display qos queue wrr interface

qos wrr

WFQ commands

display qos queue wfq interface

Use display qos queue wfq interface to display the WFQ configuration of an interface.

Syntax

display qos queue wfq interface [ interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays the WFQ configuration of all interfaces.

Examples

# Display the WFQ configuration of GigabitEthernet 1/0/1.

<Sysname> display qos wfq interface gigabitethernet 1/0/1

Interface: GigabitEthernet1/0/1

Output queue: Hardware Weighted Fair Queuing

Queue ID Queue name Group Byte count Min Bandwidth

--------------------------------------------------------------------------------

0 be 1 1 0

1 af1 1 1 0

2 af2 1 1 0

3 af3 1 1 0

4 af4 1 1 0

5 ef 1 1 0

6 cs6 1 1 0

7 cs7 1 1 0

Table 27 Command output

Field	Description
Interface	Interface type and interface number.
Output queue	Type of the current output queue.
Group	ID of the group that holds the queue.
Byte-count	Byte-count scheduling weight of the queue. N/A is displayed for a queue that uses the SP scheduling algorithm.
Weight	Packet-count queue scheduling weight of the queue. N/A is displayed for a queue that uses the SP scheduling algorithm.
Min Bandwidth	Minimum guaranteed bandwidth for the queue.

qos bandwidth queue

Use qos bandwidth queue to set the minimum guaranteed bandwidth for a queue on an interface.

Use undo qos bandwidth queue to restore the default.

Syntax

qos bandwidth queue queue-id min bandwidth-value

undo qos bandwidth queue queue-id

Default

The minimum guaranteed bandwidth is not set for a WFQ queue.

Views

Interface view

Predefined user roles

network-admin

Parameters

queue-id: Specifies a queue by its ID. The value range for this argument is 0 to 7 or keywords in Table 26.

min bandwidth-value: Sets the minimum guaranteed bandwidth in kbps. The bandwidth-value argument has the following value ranges: 8 to 10000000 for 10-GE interfaces, 8 to 25000000 for 25-GE interfaces, 8 to 100000000 for 100-GE interfaces.

Usage guidelines

The minimum guaranteed bandwidth is the amount of bandwidth guaranteed for a queue when the interface is congested.

You must use the qos wfq command to enable WFQ before you can configure this command on an interface.

Examples

# Set the minimum guaranteed bandwidth to 100 kbps for queue 0 on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos wfq weight

[Sysname-GigabitEthernet1/0/1] qos bandwidth queue 0 min 100

Related commands

qos wfq

qos wfq (interface view)

Use qos wfq to enable WFQ on an interface.

Use undo qos wfq to restore the default.

Syntax

qos wfq { byte-count | weight }

undo qos wfq { byte-count | weight }

Default

An interface uses SP queuing.

Views

Interface view

Predefined user roles

network-admin

Parameters

byte-count: Allocates bandwidth to queues in bytes.

weight: Allocates bandwidth to queues in packets.

Usage guidelines

You must use the qos wfq command to enable WFQ before you can configure WFQ queuing parameters for a queue on an interface.

Examples

# Enable packet-count WFQ on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos wfq weight

# Enable byte-count WFQ on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos wfq byte-count

Related commands

display qos queue wfq interface

qos wfq { byte-count | weight }

Use qos wfq { byte-count | weight } to assign a queue to a WFQ group with a certain scheduling weight.

Use undo qos wfq to restore the default.

Syntax

qos wfq queue-id group { 1 | 2 } { byte-count | weight } schedule-value

undo qos wfq queue-id

Default

All queues on a WFQ-enabled interface are in WFQ group 1 and have a weight of 1.

Views

Interface view

Predefined user roles

network-admin

Parameters

queue-id: Specifies a queue by its ID. The value range for this argument is 0 to 7 or keywords in Table 26.

group { 1 | 2 }: Specifies WFQ group 1 or 2. If you do not specify a group, group 1 applies. Group 1 has higher scheduling priority than group 2. Queues in group 2 are serviced only when all queues in group 1 are empty.

byte-count: Allocates bandwidth to queues in bytes.

weight: Allocates bandwidth to queues in packets.

schedule-value: Specifies a scheduling weight. The value range is 1 to 127.

Usage guidelines

You must use the qos wfq command to enable WFQ before you configure this command.

Examples

# Enable byte-count WFQ on GigabitEthernet 1/0/1, assign queue 0 to WFQ group 1, and specify scheduling weight 10 for queue 0.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos wfq byte-count

[Sysname-GigabitEthernet1/0/1] qos wfq 0 group 1 byte-count 10

Related commands

display qos queue wfq interface

qos bandwidth queue

qos wfq

qos wfq group sp

Use qos wfq group sp to assign a queue to the SP group.

Use undo qos wfq group sp to remove a queue from the SP group.

Syntax

qos wfq queue-id group sp

undo qos wfq queue-id

Default

All queues on a WFQ-enabled interface are in WFQ group 1.

Views

Interface view

Predefined user roles

network-admin

Parameters

queue-id: Specifies a queue by its ID. The value range for this argument is 0 to 7 or keywords in Table 26.

Usage guidelines

This command is available only on a WFQ-enabled interface. Queues in the SP group are scheduled with SP, instead of WFQ. The SP group has higher scheduling priority than the WFQ groups.

You must use the qos wfq command to enable WFQ before you configure this command.

Examples

# Enable WFQ on GigabitEthernet 1/0/1, and assign queue 0 to the SP group.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos wfq weight

[Sysname-GigabitEthernet1/0/1] qos wfq 0 group sp

Related commands

display qos queue wfq interface

qos bandwidth queue

qos wfq

Queue scheduling profile commands

bandwidth queue

Use bandwidth queue to set the minimum guaranteed bandwidth for a WFQ queue.

Use undo bandwidth queue to restore the default.

Syntax

bandwidth queue queue-id min bandwidth-value

undo bandwidth queue queue-id

Default

The minimum guaranteed bandwidth is not set.

Views

Queue scheduling profile view

Predefined user roles

network-admin

Parameters

queue-id: Specifies a queue by its ID. The value range for this argument is 0 to 7 or keywords in Table 26.

min bandwidth-value: Specifies the minimum guaranteed bandwidth in kbps. The value range for the bandwidth-value argument is 8 to 100000000 kbps.

Usage guidelines

You must configure a queue as a WFQ queue before you set the minimum guaranteed bandwidth for the queue.

The minimum guaranteed bandwidth is the amount of bandwidth guaranteed for a queue when the interface is congested.

Examples

# Configure queue 0 as a WFQ queue, and set the minimum guaranteed bandwidth to 100 kbps for queue 0.

<Sysname> system-view

[Sysname] qos qmprofile myprofile

[Sysname-qmprofile-myprofile] queue 0 wfq group 1 weight 1

[Sysname-qmprofile-myprofile] bandwidth queue 0 min 100

display qos qmprofile configuration

Use display qos qmprofile configuration to display the queue scheduling profile configuration.

Syntax

display qos qmprofile configuration [ profile-name ] [ slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

profile-name: Specifies a queue scheduling profile by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a queue scheduling profile, this command displays the configuration of all queue scheduling profiles.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays the queue scheduling profile configuration for the master device. ‌‌

Examples

# Display the configuration of queue scheduling profile myprofile.

<Sysname> display qos qmprofile configuration myprofile

Queue scheduling profile: myprofile (ID 1)

Queue ID Type Group Schedule Schedule Min Max

unit value bandwidth bandwidth

---------------------------------------------------------------------

be WFQ 1 byte-count 10 0 N/A

af1 WFQ 1 byte-count 20 0 N/A

af2 WFQ 1 byte-count 20 0 N/A

af3 WFQ 1 byte-count 10 0 N/A

af4 SP N/A N/A N/A 0 N/A

ef SP N/A N/A N/A 0 N/A

cs6 SP N/A N/A N/A 0 N/A

cs7 SP N/A N/A N/A 0 N/A

Table 28 Command output

Field	Description
Queue scheduling profile	Queue scheduling profile name.
Type	Queue scheduling type: · SP. · WRR. · WFQ.
Group	Priority group to which the queue belongs. N/A indicates this field is ignored.
Schedule unit	Scheduling unit: weight or byte-count. N/A indicates that this field is ignored.
Schedule value	This field indicates: · Number of packets for the weight scheduling unit. · Number of bytes for the byte-count scheduling unit. N/A indicates that this field is ignored.
Min bandwidth	Minimum guaranteed bandwidth for the queue. N/A indicates that this field is ignored.
Max bandwidth	Maximum allowed bandwidth for the queue. N/A indicates that this field is ignored.

‌

display qos qmprofile interface

Use display qos qmprofile interface to display the queue scheduling profile applied to an interface.

Syntax

display qos qmprofile interface [ interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays the queue scheduling profiles applied to all interfaces.

Examples

# Display the queue scheduling profile applied to GigabitEthernet 1/0/1.

<Sysname> display qos qmprofile interface gigabitethernet 1/0/1

Interface: GigabitEthernet1/0/1

Direction: Outbound

Queue scheduling profile: myprofile

Table 29 Command output

Field	Description
Direction	Direction in which the queue scheduling profile is applied.
Queue scheduling profile	Name of the queue scheduling profile applied to the interface.

qos apply qmprofile

Use qos apply qmprofile to apply a queue scheduling profile to the outbound direction of an interface.

Use undo qos apply qmprofile to restore the default.

Syntax

qos apply qmprofile profile-name

undo qos apply qmprofile

Default

No queue scheduling profile is applied to an interface.

Views

Interface view

Predefined user roles

network-admin

Parameters

profile-name: Specifies a queue scheduling profile by its name, a case-sensitive string of 1 to 31 characters.

Usage guidelines

You can apply only one queue scheduling profile to an interface.

Examples

# Apply queue scheduling profile myprofile to the outbound direction of GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos apply qmprofile myprofile

Related commands

display qos qmprofile interface

qos qmprofile

Use qos qmprofile to create a queue scheduling profile and enter its view, or enter the view of an existing queue scheduling profile.

Use undo qos qmprofile to delete a queue scheduling profile.

Syntax

qos qmprofile profile-name

undo qos qmprofile profile-name

Default

No user-created queue scheduling profiles exist.

Views

System view

Predefined user roles

network-admin

Parameters

profile-name: Specifies a name for the queue scheduling profile, a case-sensitive string of 1 to 31 characters.

Usage guidelines

To delete a queue scheduling profile already applied to an object, first remove it from the object.

Examples

# Create a queue scheduling profile named myprofile and enter queue scheduling profile view.

<Sysname> system-view

[Sysname] qos qmprofile myprofile

[Sysname-qmprofile-myprofile]

Related commands

display qos qmprofile interface

queue

queue (queue scheduling profile view)

Use queue to configure queue scheduling parameters.

Use undo queue to delete queue scheduling parameter settings.

Syntax

queue queue-id { sp | wfq group group-id { weight | byte-count } schedule-value | wrr group group-id { weight | byte-count } schedule-value }

undo queue queue-id

Default

All queues in a queue scheduling profile are SP queues.

Views

Queue scheduling profile view

Predefined user roles

network-admin

Parameters

queue-id: Specifies a queue by its ID. The value range for this argument is 0 to 7 or keywords in Table 26.

sp: Enables SP for the queue.

wfq: Enables WFQ for the queue.

wrr: Enables WRR for the queue.

group group-id: Specifies a WFQ or WRR group by its ID. The value range is 1 and 2.

byte-count: Allocates bandwidth to queues in bytes.

weight: Allocates bandwidth to queues in packets.

schedule-value: Specifies the scheduling weight. The value range is 1 to 127.

Examples

# Create a queue scheduling profile named myprofile, and configure queue 0 to use SP.

<Sysname> system-view

[Sysname] qos qmprofile myprofile

[Sysname-qmprofile-myprofile] queue 0 sp

# Create a queue scheduling profile named myprofile. Configure queue 1 to meet the following requirements:

· The WRR queuing is used.

· The WRR group is group 1.

· The scheduling weight is 10.

<Sysname> system-view

[Sysname] qos qmprofile myprofile

[Sysname-qmprofile-myprofile] queue 1 wrr group 1 weight 10

Related commands

display qos qmprofile interface

qos qmprofile

Congestion avoidance commands

WRED commands

display qos wred interface

Use display qos wred interface to display the WRED information for interfaces.

Syntax

display qos wred interface [ interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays the WRED information for all interfaces.

Examples

# Display the WRED information for all interfaces.

<Sysname> display qos wred interface

Interface: GigabitEthernet1/0/3

Current WRED configuration:

Applied WRED table name: q1

Table type: Queue based WRED

QID gmin gmax gpro ymin ymax ypro rmin rmax rpro

----------------------------------------------------------------------------

0 100 1000 10 100 1000 10 100 1000 10

1 100 1000 10 100 1000 10 100 1000 10

2 100 1000 10 100 1000 10 100 1000 10

3 100 1000 10 100 1000 10 100 1000 10

4 100 1000 10 100 1000 10 100 1000 10

5 100 1000 10 100 1000 10 100 1000 10

6 100 1000 10 100 1000 10 100 1000 10

7 100 1000 10 100 1000 10 100 1000 10

Table 30 Command output

Field	Description
Interface	Interface type and interface number.
Table type	Type of a WRED table.
QID	Queue ID.
gmin	Lower limit for green packets.
gmax	Upper limit for green packets.
gprob	Drop probability for green packets.
ymin	Lower limit for yellow packets.
ymax	Upper limit for yellow packets.
yprob	Drop probability for yellow packets.
rmin	Lower limit for red packets.
rmax	Upper limit for red packets.
rprob	Drop probability for red packets.
exp	Exponent for average queue length calculation.

‌

display qos wred table

Use display qos wred table to display the WRED table configuration.

Syntax

display qos wred table [ name table-name ] [ slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

name table-name: Specifies a WRED table by its name, a case-sensitive string of 1 to 32 characters. If you do not specify a WRED table, this command displays the configuration of all WRED tables.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays the WRED table configuration for the master device. ‌‌

Examples

# Display the configuration of WRED table 1.

<Sysname> display qos wred table name 1

Table name: 1

Table type: Queue based WRED

QID gmin gmax gprob ymin ymax yprob rmin rmax rpro

-----------------------------------------------------------------

0 100 1000 10 100 1000 10 100 1000 10

1 100 1000 10 100 1000 10 100 1000 10

2 100 1000 10 100 1000 10 100 1000 10

3 100 1000 10 100 1000 10 100 1000 10

4 100 1000 10 100 1000 10 100 1000 10

5 100 1000 10 100 1000 10 100 1000 10

6 100 1000 10 100 1000 10 100 1000 10

7 100 1000 10 100 1000 10 100 1000 10

Table 31 Command output

Field	Description
Table name	Name of a WRED table.
Table type	Type of a WRED table.
QID	Queue ID.
gmin	Lower limit for green packets.
gmax	Upper limit for green packets.
gprob	Drop probability for green packets.
ymin	Lower limit for yellow packets.
ymax	Upper limit for yellow packets.
yprob	Drop probability for yellow packets.
rmin	Lower limit for red packets.
rmax	Upper limit for red packets.
rpro	Drop probability for red packets.

qos wred apply

Use qos wred apply to apply a WRED table to an interface.

Use undo qos wred apply to restore the default.

Syntax

qos wred apply [ table-name ]

undo qos wred apply

Default

No WRED table is applied to an interface, and the tail drop mode is used on an interface.

Views

Layer 2/Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

table-name: Specifies a WRED table by its name, a case-sensitive string of 1 to 32 characters. If you do not specify a WRED table, this command applies the default WRED table to the interface.

Examples

# Apply WRED table table1 to GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] qos wred apply table1

Related commands

display qos wred interface

display qos wred table

qos wred queue table

Use qos wred queue table to create a WRED table and enter its view, or enter the view of an existing WRED table.

Use undo qos wred queue table to delete a WRED table.

Syntax

qos wred queue table table-name

undo qos wred queue table table-name

Default

No WRED tables exist.

Views

System view

Predefined user roles

network-admin

Parameters

table table-name: Specifies a name for the WRED table, a case-sensitive string of 1 to 32 characters.

Usage guidelines

You cannot delete a WRED table in use. To delete it, first remove it from the specified interface.

You can use the display qos wred table command to display the default WRED table, which cannot be modified or deleted.

Examples

# Create a queue-based WRED table named queue-table1.

<Sysname> system-view

[Sysname] qos wred queue table queue-table1

[Sysname-wred-table-queue-table1]

Related commands

display qos wred table

queue (WRED table view)

Use queue to configure the drop-related parameters for a queue in the queue-based WRED table.

Use undo queue to restore the default.

Syntax

queue queue-id [ drop-level drop-level ] low-limit low-limit high-limit high-limit [ discard-probability discard-prob ]

undo queue { queue-id [ drop-level drop-level ] | all }

Default

The lower limit is 100, the upper limit is 1000, and the drop probability is 10%.

Views

WRED table view

Predefined user roles

network-admin

Parameters

all: Specifies all queues.

queue-id: Specifies a queue by its ID. The value range for this argument is 0 to 7.

drop-level drop-level: Specifies a drop level. This argument is a consideration for dropping packets. The value 0 corresponds to green packets, the value 1 corresponds to yellow packets, and the value 2 corresponds to red packets. If you do not specify a drop level, the subsequent configuration takes effect on the packets in the queue regardless of the drop level.

low-limit low-limit: Specifies the lower limit for the average queue length. The value range for low-limit is 0 to 16383 cell resources. A cell resource is 256 bytes.

high-limit high-limit: Specifies the upper limit for the average queue length. The upper limit must be greater than the lower limit. The value range for high-limit is 0 to 16383 cell resources. A cell resource is 256 bytes.

discard-probability discard-prob: Specifies the denominator for drop probability calculation. The greater the denominator, the greater the calculated drop probability. The value range for discard-prob is 0 to 100.

Usage guidelines

When the average queue size is smaller than the lower threshold, no packet is dropped. When the average queue size is between the lower threshold and the upper threshold, the packets are dropped at random. The longer the queue is, the higher the drop probability is. When the average queue size exceeds the upper threshold, subsequent packets are dropped.

If you configure the same value for the lower limit and higher limit and set the drop probability to 100%, tail drop is used for the queue.

Examples

# In queue-based WRED table queue-table1, configure the following drop-related parameters for packets in queue 1:

· The drop level is 1.

· The lower limit for the average queue length is 10.

· The upper limit for the average queue length is 20.

· The drop probability is 30%.

<Sysname> system-view

[Sysname] qos wred queue table queue-table1

[Sysname-wred-table-queue-table1] queue 1 drop-level 1 low-limit 10 high-limit 20 discard-probability 30

Related commands

display qos wred table

qos wred queue table

Global CAR commands

car name

Use car name to use a global CAR action in a traffic behavior.

Use undo car to restore the default.

Syntax

car name car-name

undo car

Default

No global CAR action is configured in a traffic behavior.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

car-name: Specifies the name of an aggregate CAR action. This argument must start with a letter, and is a case-sensitive string of 1 to 31 characters.

Examples

# Use aggregate CAR action aggcar-1 in traffic behavior be1.

<Sysname> system-view

[Sysname] traffic behavior be1

[Sysname-behavior-be1] car name aggcar-1

Related commands

display qos car name

display traffic behavior user-defined

display qos car name

Use display qos car name to display information about global CAR actions.

Syntax

display qos car name [ car-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

car-name: Specifies a global CAR action by its name. This argument must start with a letter, and is a case-sensitive string of 1 to 31 characters. If you do not specify a global CAR action, this command displays information about all global CAR actions.

Examples

# ‌‌Display information about all global CAR actions.

<Sysname> display qos car name

Name: a

Mode: aggregative

CIR 100 (kbps) CBS: 51200 (Bytes) PIR: 800 (kbps) EBS: 0 (Bytes)

Green action : pass

Yellow action : pass

Red action : discard

Table 32 Command output

Field	Description
Name	Name of the global CAR action.
Mode	Type of the CAR action, which can be aggregative.
CIR CBS PIR EBS	Parameters for the CAR action.
Green action	Action to take on green packets: · discard—Drops the packets. · pass—Permits the packets to pass through.
Yellow action	Action to take on yellow packets: · discard—Drops the packets. · pass—Permits the packets to pass through.
Red action	Action to take on red packets: · discard—Drops the packets. · pass—Permits the packets to pass through.
Green packets	Statistics about green packets.
Yellow packets	Statistics about yellow packets.
Red packets	Statistics about red packets.

qos car (system view)

Use qos car aggregative to configure an aggregate or hierarchical CAR action.

Use undo qos car to delete an aggregate or hierarchical CAR action.

Syntax

qos car car-name aggregative cir committed-information-rate [ cbs committed-burst-size [ ebs excess-burst-size ] ] [ green action | red action | yellow action ] *

qos car car-name aggregative cir committed-information-rate [ cbs committed-burst-size ] pir peak-information-rate [ ebs excess-burst-size ] [ green action | red action | yellow action ] *

undo qos car car-name

Default

No aggregate CAR action is configured.

Views

System view

Predefined user roles

network-admin

Parameters

car-name: Specifies the name of the aggregate CAR action. This argument must start with a letter, and is a case-sensitive string of 1 to 31 characters.

cir committed-information-rate: Specifies the CIR in kbps, which is an average traffic rate. The value range for committed-information-rate is 10 to 100000000, in increments of 10.

pir peak-information-rate: Specifies the PIR in kbps. The value range for peak-information-rate is 10 to 100000000, in increments of 10. This option is supported only in aggregate CAR actions.

green action: Specifies the action to take on packets that conform to CIR. The default setting is pass.

red action: Specifies the action to take on the packet that conforms to neither CIR nor PIR. The default setting is discard.

yellow action: Specifies the action to take on packets that conform to PIR but not to CIR. The default setting is pass.

action: Sets the action to take on the packet:

· discard: Drops the packet.

· pass: Permits the packet to pass through.

Usage guidelines

To use two rates for aggregate CAR, configure the qos car command with the pir peak-information-rate option. To use one rate for aggregate CAR, configure the qos car command without the pir peak-information-rate option.

A n aggregate CAR action takes effect only after it is used in a QoS policy.

Examples

# Configure aggregate CAR action aggcar-1, where CIR is 25600, CBS is 512000, and red packets are dropped.

<Sysname> system-view

[Sysname] qos car aggcar-1 aggregative cir 25600 cbs 512000 red discard

Related commands

display qos car name

reset qos car name

Use reset qos car name to clear the statistics about aggregate CAR actions.

Syntax

reset qos car name [ car-name ]

Views

User view

Predefined user roles

network-admin

Parameters

car-name: Specifies an aggregate CAR action by its name. This argument must start with a letter, and is a case-sensitive string of 1 to 31 characters. If you do not specify an aggregate CAR action, this command clears statistics for all aggregate CAR actions.

Examples

# Clear the statistics about global CAR action aggcar-1.

<Sysname> reset qos car name aggcar-1

Queue-based accounting commands

display qos queue-statistics interface outbound

Use display qos queue-statistics interface outbound to display outgoing traffic statistics collected for interfaces on a per-queue basis.

Syntax

display qos queue-statistics interface [ interface-type interface-number ] outbound

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays the outgoing traffic statistics for all interfaces.

Examples

# Display queue-based outgoing traffic statistics of GigabitEthernet 1/0/1.

<Sysname> display qos queue-statistics interface gigabitethernet 1/0/1 outbound

Interface: GigabitEthernet1/0/1

Direction: outbound

Forwarded: 0 packets, 0 bytes

Dropped: 0 packets, 0 bytes

Queue 0

Forwarded: 0 packets, 0 bytes, 0 pps, 0 bps

Dropped: 0 packets, 0 bytes

Current queue length: 0 cells (0 bytes)

…

Queue 7

Forwarded: 0 packets, 0 bytes, 0 pps, 0 bps

Dropped: 0 packets, 0 bytes

Current queue length: 0 cells (0 bytes)

Table 33 Command output

Field	Description
Interface	Interface for which queue-based traffic statistics are displayed.
Direction	Direction of traffic for which statistics are collected.
Forwarded	Counts forwarded traffic both in the number of packets, in the number of bytes, and in the number of packets or bits per second.
Dropped	Counts dropped traffic both in packets and in bytes.
Current queue length	Current number of packets in the queue.

Related commands

reset counters interface (Interface Command Reference)

08-ACL and QoS Command Reference

QoS policy commands

display traffic classifier

remark ip-precedence

remark service-vlan-id

control-plane management

qos apply policy (interface view, control plane view, control-plane management view)

qos trust (interface view)

GTS commands

SP commands

display qos queue sp interface

qos sp (interface view)

qos wrr (interface view)

qos wrr { byte-count | weight }

qos bandwidth queue

qos wfq (interface view)

qos wfq { byte-count | weight }

qos wfq group sp

Queue scheduling profile commands

display qos qmprofile interface

qos qmprofile

queue (queue scheduling profile view)

Congestion avoidance commands

display qos queue-statistics interface outbound

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

News & Events

Contact Us