Contents

Configuring tunnel interfaces· 1

About tunnel interfaces· 1

Restrictions and guidelines: Tunnel interface configuration· 1

Configuring a tunnel interface· 1

Tunnel interface configuration tasks at a glance· 1

Creating a tunnel interface· 1

Configuring parameters for tunneled packets· 2

Restoring the default settings of the tunnel interface· 3

Setting the statistics collection mode for tunneled traffic· 3

Enabling tunnel traffic forwarding acceleration· 3

Enabling dropping IPv6 packets that use IPv4-compatible IPv6 addresses· 4

Enabling SNMP notifications for the tunneling module· 4

Verifying and maintaining tunnel interface configuration· 5

Displaying tunnel interface information· 5

Clearing tunnel interface statistics· 5

Troubleshooting tunnel interface configuration· 5

Tunnel interface not up· 5

 

Configuring tunnel interfaces

About tunnel interfaces

Tunneling encapsulates the packets of a network protocol within the packets of a second network protocol and transfers them over a virtual point-to-point connection. The virtual connection is called a tunnel. Packets are encapsulated at the tunnel source and de-encapsulated at the tunnel destination.

Configure a tunnel interface (Layer 3 virtual interface) at both ends of a tunnel. The devices use the tunnel interface to identify, process, and send packets for the tunnel.

Restrictions and guidelines: Tunnel interface configuration

Do not specify the same tunnel source and destination addresses for the tunnel interfaces on the same device.

For information about the description, bandwidth, and shutdown commands, see common interface commands in Interface Command Reference.

You do not need to use the ip address or ipv6 address command to configure an IPv4 or IPv6 address for an IPv4 VXLAN and IPv6 VXLAN tunnel interface. For more information about the ip address and ipv6 address commands, see IP addressing commands and IPv6 basics commands in Layer 3—IP Services Command Reference, respectively.

Configuring a tunnel interface

Tunnel interface configuration tasks at a glance

To configure a tunnel interface, perform the following tasks:

1.     Creating a tunnel interface

2.     (Optional.) Configuring parameters for tunneled packets

3.     (Optional.) Restoring the default settings of the tunnel interface

4.     (Optional.) Setting the statistics collection mode for tunneled traffic

5.     (Optional.) Enabling SNMP notifications for the tunneling module

Creating a tunnel interface

1.     Enter system view.

system-view

2.     Create a tunnel interface, specify the tunnel mode, and enter tunnel interface view.

interface tunnel number  mode { gre [ ipv6 ] | ipv4-ipv4 | ipv4-ipv6 | ipv6-ipv4 [ 6to4 | auto-tunnel | isatap ] | ipv6-ipv6 | vxlan [ ipv6 ] }

For packet tunneling to succeed, the two ends of a tunnel must use the same tunnel mode.

3.     Configure a source address or source interface for the tunnel interface.

source { ipv4-address | ipv6-address | interface-type interface-number }

By default, no source address or source interface is configured for the tunnel interface.

If you specify a source address, it is used as the source address of tunneled packets.

If you specify a source interface, the primary IP address of this interface is used as the source IP address of tunneled packets.

4.     Configure a destination address for the tunnel interface.

destination { ipv4-address | ipv6-address }

By default, no destination address is configured for the tunnel interface.

The tunnel destination address must be the IP address of the receiving interface on the tunnel peer. It is used as the destination IP address of tunneled packets.

5.     (Optional.) Configure a description for the interface.

description text

By default, the description for a tunnel interface is Tunnel number Interface.

6.     (Optional.) Set the MTU of the tunnel interface.

mtu size

The default settings are as follows:

¡     If the tunnel interface has never been up, the MTU is 64000 bytes.

¡     If the tunnel interface is up, its MTU is identical to the outgoing interface's MTU minus the length of the tunnel headers. The outgoing interface is automatically obtained through routing table lookup based on the tunnel destination address.

7.     (Optional.) Set the expected bandwidth for the tunnel interface.

bandwidth bandwidth-value

The default expected bandwidth (in kbps) is the interface maximum rate divided by 1000.

The expected bandwidth is an informational parameter used only by higher-layer protocols for calculation. You cannot adjust the actual bandwidth of an interface by using this command.

8.     Bring up the tunnel interface.

undo shutdown

By default, a tunnel interface is not administratively down.

Configuring parameters for tunneled packets

1.     Enter system view.

system-view

2.     Enter tunnel interface view.

interface tunnel number

3.     Set the ToS for tunneled packets.

tunnel tos tos-value

The default setting is the same as the ToS of the original packets.

4.     Set the TTL for tunneled packets.

tunnel ttl ttl-value

The default TTL for tunneled packets is 255.

5.     Set the DF bit for tunneled packets.

tunnel dfbit enable

By default, the DF bit is not set for tunneled packets.

Restoring the default settings of the tunnel interface

Restrictions and guidelines

	CAUTION: This operation might interrupt ongoing network services. Make sure you are fully aware of the impact of this operation when you perform it on a live network.

 

This operation might fail to restore the default settings for some commands for reasons such as command dependencies or system restrictions. Use the display this command in interface view to identify these commands. Use their undo forms or follow the command reference to restore their default settings. If your restoration attempt still fails, follow the error message instructions to resolve the problem.

For more information about the default command, see common interface commands in Interface Command Reference.

Procedure

1.     Enter system view.

system-view

2.     Enter tunnel interface view.

interface tunnel number

3.     Restore the default settings of the tunnel interface.

default

Setting the statistics collection mode for tunneled traffic

About this task

The device provides the following statistics collection mode for tunneled traffic:

·     Payload—In this mode, the device counts bytes in packets before the packets are encapsulated.

·     Encapsulation—In this mode, the device counts bytes in the entire packets after the packets are encapsulated.

Procedure

1.     Enter system view.

system-view

2.     Set the statistics collection mode for tunneled traffic.

tunnel statistics-mode { encapsulation | payload }

By default, the payload mode is used.

 

 

Enabling tunnel traffic forwarding acceleration

About this task

Enable tunnel traffic forwarding acceleration to accelerate the forwarding of tunneled packets when the AFT and LB services are not deployed.

Procedure

1.     Enter system view.

system-view

2.     Enable tunnel traffic forwarding acceleration.

tunnel accelerate

By default, tunnel traffic forwarding acceleration is disabled.

Enabling dropping IPv6 packets that use IPv4-compatible IPv6 addresses

Restrictions and guidelines

Automatic IPv4-compatible IPv6 tunnels do not support this feature.

Procedure

1.     Enter system view.

system-view

2.     Enable dropping IPv6 packets that use IPv4-compatible IPv6 addresses.

tunnel discard ipv4-compatible-packet

By default, IPv6 packets that use IPv4-compatible IPv6 addresses are not dropped.

Enabling SNMP notifications for the tunneling module

About this task

After you enable the max-threshold-reached notification, when the number of tunnel interfaces exceeds the warning threshold (80% of the maximum), the device generates SNMP notifications that record the chassis number and slot number of the exceeding tunnel interfaces.

After you enable the vxlan-config-failure notification, when a VXLAN tunnel failed to be deployed, the device generates an SNMP notification that records the interface number of the tunnel.

After you enable the vxlan-decap-failure notification, when a VXLAN packet failed to be decapsulated, the device generates an SNMP notification that records the source IP type, source IP address, destination IP type, and destination IP address of the VXLAN packet.

After you enable the vxlan-tunnel-status notification, the device generates SNMP notifications for VXLAN over IPv4 tunnels when the tunnel status changes.

After you enable the vxlan-ipv6-tunnel-status notification, the device generates SNMP notifications for VXLAN over IPv6 tunnels when the tunnel status changes.

If you do not specify the notification types to be enabled, the device enables SNMP notifications for both VXLAN over IPv4 and VXLAN over IPv6 tunnel status change events.

To output tunnel notifications correctly, you must also configure parameters for sending SNMP notifications.

For more information about SNMP configuration, see Network Management and Monitoring Configuration Guide.

Procedure

1.     Enter system view.

system-view

2.     Enable SNMP notifications for the tunneling module.

snmp-agent trap enable tunnel [ max-threshold-reached | vxlan-config-failure | vxlan-decap-failure | vxlan-tunnel-status | vxlan-ipv6-tunnel-status ] *

By default, SNMP notifications for the tunneling module are disabled.

Verifying and maintaining tunnel interface configuration

Displaying tunnel interface information

Perform display tasks in any view.

·     Display tunnel interface information.

display tunnel-interface [ number ]

·     Display information about tunnel interfaces.

display interface [ tunnel [ number ] ] [ brief [ description | down ] ]

·     Display IPv6 information on tunnel interfaces.

display ipv6 interface [ tunnel [ number ] ] [ brief ]

For more information about this command, see IPv6 basics commands in Layer 3—IP Services Command Reference.

Clearing tunnel interface statistics

Perform clear tasks in user view.

·     Clear statistics on tunnel interfaces.

reset counters interface [ tunnel [ number ] ]

For more information about this command, see common interface commands in Interface Command Reference.

·     Clear IPv6 statistics on tunnel interfaces.

reset ipv6 statistics [ slot slot-number ]

For more information about this command, see IPv6 basics commands in Layer 3—IP Services Command Reference.

Troubleshooting tunnel interface configuration

Tunnel interface not up

Symptom

A tunnel interface configured with related parameters such as tunnel source address, tunnel destination address, and tunnel mode cannot come up.

Analysis

The physical interface of the tunnel does not come up, or the tunnel destination is unreachable.

Solution

1.     To resolve the issue:

¡     Use the display interface or display ipv6 interface command to verify that the physical interface of the tunnel is up. If the physical interface is down, check the network connection.

¡     Use the display ipv6 routing-table or display ip routing-table command to verify that the tunnel destination is reachable. If the route is not available, configure a route to reach the tunnel destination.

2.     If the issue persists, contact H3C Support.