Non-default vSystems do not support some of the multicast routing and forwarding commands. For information about vSystem support for a command, see the usage guidelines on that command. For information about vSystem, see Virtual Technologies Configuration Guide.

delete ip rpf-route-static

Use delete ip rpf-route-static to delete all static multicast routes.

Syntax

delete ip rpf-route-static [ vpn-instance vpn-instance-name ]

Views

System view

Predefined user roles

network-admin

context-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command deletes all static multicast routes on the public network.

Usage guidelines

Non-default vSystems do not support this command.

This command deletes all static multicast routes. To delete a specified static multicast route, use the undo ip rpf-route-static command.

Examples

# Delete all static multicast routes on the public network.

<Sysname> system-view

[Sysname] delete ip rpf-route-static

This will erase all multicast static routes and their configurations, you must reconfigure all static routes.

Are you sure?[Y/N]:y

Related commands

ip rpf-route-static

display mrib interface

Use display mrib interface to display information about interfaces maintained by the MRIB.

Syntax

display mrib [ vpn-instance vpn-instance-name ] interface [ interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

vsys-admin

vsys-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays information about interfaces maintained by the MRIB on the public network.

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays information about all interfaces maintained by the MRIB.

Examples

# Display information about interfaces maintained by the MRIB on the public network.

<Sysname> display mrib interface

Interface: GigabitEthernet1/0/1

Index: 0x00004444

Current state: up

MTU: 1500

Type: BROADCAST

Protocol: PIM-DM

PIM protocol state: Enabled

Address list:

1. Local address : 8.12.0.2/16

Remote address: 0.0.0.0

Reference : 1

State : NORMAL

Table 1 Command output

Field	Description
Interface	Interface name.
Index	Index number of the interface.
Current state	Current status of the interface: up or down.
MTU	MTU value.
Type	Interface type: · BROADCAST—Broadcast link interface. · P2P—P2P interface. · LOOP—Loopback interface. · REGISTER—Register interface. · NBMA—NBMA interface. · MTUNNEL—Multicast tunnel interface. This field is empty if the interface is Null 0.
Protocol	Protocol running on the interface: PIM-DM, PIM-SM, IGMP, PROXY, or MD.
PIM protocol state	Whether PIM is enabled: Enabled or Disabled.
Address list	Interface address list.
Local address	Local IP address.
Remote address	Remote end IP address. This field is displayed only when the interface is vlink type.
Reference	Number of times that the address has been referenced.
State	Status of the interface address: NORMAL or DEL.

display multicast boundary

Use display multicast boundary to display multicast boundary information.

Syntax

display multicast [ vpn-instance vpn-instance-name ] boundary [ group-address [ mask-length | mask ] ] [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays multicast boundary information on the public network.

group-address: Specifies a multicast group by its IP address in the range of 224.0.0.0 to 239.255.255.255. If you do not specify a multicast group, this command displays multicast boundary information for all multicast groups.

mask-length: Specifies an address mask length in the range of 4 to 32. The default is 32.

mask: Specifies an address mask. The default is 255.255.255.255.

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays multicast boundary information for all interfaces.

Usage guidelines

Non-default vSystems do not support this command.

Examples

# Display information about all multicast boundaries on the public network.

<Sysname> display multicast boundary

Boundary Interface

224.1.1.0/24 GE1/0/1

239.2.2.0/24 GE1/0/2

Table 2 Command output

Field	Description
Boundary	Multicast group associated with the multicast boundary.
Interface	Boundary interface associated with the multicast boundary.

Related commands

multicast boundary

display multicast fast-forwarding cache

Use display multicast fast-forwarding cache to display multicast fast forwarding entries.

Syntax

In standalone mode:

display multicast [ vpn-instance vpn-instance-name ] fast-forwarding cache [ source-address | group-address ] * [ slot slot-number [ cpu cpu-number ] ]

In IRF mode:

display multicast [ vpn-instance vpn-instance-name ] fast-forwarding cache [ source-address | group-address ] * [chassis chassis-number slot slot-number [ cpu cpu-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

vsys-admin

vsys-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays multicast fast forwarding entries on the public network.

source-address: Specifies a multicast source address.

group-address: Specifies a multicast group address in the range of 224.0.1.0 to 239.255.255.255.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays multicast fast forwarding entries for the MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify a card, this command displays multicast fast forwarding entries for the global active MPU. (In IRF mode.)

cpu cpu-number: Specifies a CPU by its number. This option is available only if multiple CPUs are available on the specified slot.

Examples

# Display multicast fast forwarding entries on the public network.

<Sysname> display multicast fast-forwarding cache

Total 1 entries, 1 matched

(60.1.1.200, 225.0.0.2)

Status : Enabled

Source port: 2001 Destination port: 2002

Protocol : 2 Flag : 0x2

Incoming interface: GigabitEthernet1/0/3

List of 1 outgoing interfaces:

GigabitEthernet1/0/2

Status: Enabled Flag: 0x14

Table 3 Command output

Field	Description
Total 1 entries, 1 matched	Total number of (S, G) entries in the multicast fast forwarding table, and the total number of matching (S, G) entries.
(60.1.1.200, 225.0.0.2)	(S, G) entry.
Protocol	Protocol number.
Flag	Flag of the (S, G) entry or the outgoing interface in the entry. This field displays one flag or the sum of multiple flags. In this example, the value 0x2 means that the entry has only one flag 0x2. The value 0x14 means that the interface has flags 0x4 and 0x10. The following flags are available for an entry: · 0x1—The entry is created because of packets passed through between cards. · 0x2—The entry is added by multicast forwarding. The following flags are available for an outgoing interface: · 0x1—The interface is added to the entry because of packets passed through between cards. · 0x2—The interface is added to an existing entry. · 0x4—The MAC address of the interface is needed for fast forwarding. · 0x8—The interface is an outgoing interface associated with the incoming VLAN interface. · 0x10—The interface is associated with the entry. · 0x20—The interface is to be deleted.
Status	Status of the (S, G) entry or the outgoing interface: · Enabled—Available. · Disabled—Unavailable.
Incoming interface	Incoming interface of the (S, G) entry.
List of 1 outgoing interfaces	Outgoing interface list of the (S, G) entry.

Related commands

reset multicast fast-forwarding cache all

display multicast forwarding df-info

Use display multicast forwarding df-info to display DF information.

Syntax

In standalone mode:

display multicast [ vpn-instance vpn-instance-name ] forwarding df-info [ rp-address ] [ verbose ] [ slot slot-number [ cpu cpu-number ] ]

In IRF mode:

display multicast [ vpn-instance vpn-instance-name ] forwarding df-info [ rp-address ] [ verbose ] [ chassis chassis-number slot slot-number [ cpu cpu-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

vsys-admin

vsys-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays DF information on the public network.

rp-address: Specifies a BIDIR-PIM RP by its IP address.

verbose: Specifies detailed information. If you do not specify this keyword, the command displays brief information about DFs.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays DF information for the MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify a card, this command displays DF information for the global active MPU. (In IRF mode.)

cpu cpu-number: Specifies a CPU by its number. This option is available only if multiple CPUs are available on the specified slot.

Usage guidelines

In a BIDIR-PIM domain, only the DF on each subnet can forward multicast data destined for a multicast group toward the RP of the group. For more information about the DF, see IP Multicast Configuration Guide.

Examples

# Display brief information about DFs on an ADVPN network.

<Sysname> display multicast forwarding df-info

Total 1 RPs, 1 matched

00001. RP address: 1.1.1.1

Flags: 0x0

Uptime: 00:00:53

RPF interface: Tunnel2, 192.168.0.1

List of 2 DF interfaces:

1: LoopBack0

2: Tunnel2, 192.168.0.3

# Display brief information about DFs on the public network.

<Sysname> display multicast forwarding df-info

Total 1 RPs, 1 matched

00001. RP address: 7.11.0.2

Flags: 0x0

Uptime: 04:14:40

RPF interface: GigabitEthernet1/0/1

List of 1 DF interfaces:

1: GigabitEthernet1/0/2

# Display detailed information about DFs on the public network.

<Sysname> display multicast forwarding df-info verbose

Total 1 RPs, 1 matched

00001. RP address: 7.11.0.2

MID: 2, Flags: 0x0

Uptime: 03:37:22

Product information: 0x7a2f762f, 0x718fee9f, 0x4b82f137, 0x71c32184

RPF interface: GigabitEthernet1/0/1

Product information: 0xa567d6fc, 0xadeb03e3

Tunnel information: 0xdfb107d4, 0x7aa5d510

List of 1 DF interfaces:

1: GigabitEthernet1/0/2

Product information: 0xa986152b, 0xb74a9a2f

Tunnel information: 0x297ca208, 0x76985b89

Table 4 Command output

Field	Description
Total 1 RPs, 1 matched	Total number of RPs, and the total number of matching RPs.
00001	Sequence number of the entry to which the RP is designated.
RP address	IP address of the RP.
MID	ID of the entry to which the RP is designated. Each entry to which the RP is designated has a unique MID.
Flags	Entry flag. This field displays one flag or the sum of multiple flags. In this example, the value 0x0 means that the entry has only one flag 0x0. The following flags are available for an entry: · 0x0—The entry is in correct state. · 0x4—The entry fails to update. · 0x8—DF interface information fails to update for the entry. · 0x40—The entry is to be deleted. · 0x100—The entry is being deleted. · 0x200—The entry is in GR state.
Uptime	Length of time for which the entry has been up.
RPF interface	RPF interface to the RP.
List of 1 DF interfaces	DF interface list.
Tunnel2, 192.168.0.3	ADVPN tunnel interface, and the IP address of the remote end.

display multicast forwarding event

Use display multicast forwarding event to display statistics of multicast forwarding events.

Syntax

In standalone mode:

display multicast [ vpn-instance vpn-instance-name ] forwarding event [ slot slot-number [ cpu cpu-number ] ]

In IRF mode:

display multicast [ vpn-instance vpn-instance-name ] forwarding event [ chassis chassis-number slot slot-number [ cpu cpu-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

vsys-admin

vsys-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays statistics of the multicast forwarding events on the public network.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays statistics of multicast forwarding events for the MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify a card, this command displays statistics of multicast forwarding events for the global active MPU. (In IRF mode.)

cpu cpu-number: Specifies a CPU by its number. This option is available only if multiple CPUs are available on the specified slot.

Examples

# Display statistics of multicast forwarding events on the public network.

<Sysname> display multicast forwarding event

Total active events sent: 0

Total inactive events sent: 0

Total NoCache events sent: 2

Total NoCache events dropped: 0

Total WrongIF events sent: 0

Total WrongIF events dropped: 0

Total SPT switch events sent: 0

NoCache rate limit: 1024 packets/s

WrongIF rate limit: 1 packets/10s

Total timer of register suppress timeout: 0

Table 5 Command output

Field	Description
Total active events sent	Number of times that entry-active events have been sent.
Total inactive events sent	Number of times that entry-inactive events have been sent.
Total NoCache events sent	Number of times that NoCache events have been sent.
Total NoCache events dropped	Number of times that NoCache events have been dropped.
Total WrongIF events sent	Number of times that WrongIF events have been sent.
Total WrongIF events dropped	Number of times that WrongIF events have been dropped.
Total SPT switch events sent	Number of times that SPT-switch events have been sent.
NoCache rate limit	Rate limit for sending NoCache events, in pps.
WrongIF rate limit	Rate limit for sending WrongIF events, in packets per 10 seconds.
Total timer of register suppress timeout	Number of times that the registration suppression has timed out in total.

Related commands

reset multicast forwarding event

display multicast forwarding-table

Use display multicast forwarding-table to display multicast forwarding entries.

Syntax

In standalone mode:

display multicast [ vpn-instance vpn-instance-name ] forwarding-table [ source-address [ mask { mask-length | mask } ] | group-address [ mask { mask-length | mask } ] | incoming-interface interface-type interface-number | outgoing-interface { exclude | include | match } interface-type interface-number | slot slot-number [ cpu cpu-number ] | statistics ] *

In IRF mode:

display multicast [ vpn-instance vpn-instance-name ] forwarding-table [ source-address [ mask { mask-length | mask } ] | group-address [ mask { mask-length | mask } ] | chassis chassis-number slot slot-number [ cpu cpu-number ] | incoming-interface interface-type interface-number | outgoing-interface { exclude | include | match } interface-type interface-number | statistics ] *

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

vsys-admin

vsys-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays multicast forwarding entries on the public network.

source-address: Specifies a multicast source address.

group-address: Specifies a multicast group address in the range of 224.0.0.0 to 239.255.255.255.

mask-length: Specifies an address mask length. The default value is 32. For a multicast group address, the value range for this argument is 4 to 32. For a multicast source address, the value range for this argument is 0 to 32.

mask: Specifies an address mask. The default value is 255.255.255.255.

incoming-interface: Specifies the multicast forwarding entries that contain the specified incoming interface.

interface-type interface-number: Specifies an incoming interface by its type and number.

outgoing-interface: Specifies the multicast forwarding entries that contain the specified outgoing interface.

exclude: Specifies the multicast forwarding entries that do not contain the specified interface in the outgoing interface list.

include: Specifies the multicast forwarding entries that contain the specified interface in the outgoing interface list.

match: Specifies the forwarding entries that contain only the specified interface in the outgoing interface list.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays multicast forwarding entries for the MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify a card, this command displays multicast forwarding entries for the global active MPU. (In IRF mode.)

cpu cpu-number: Specifies a CPU by its number. This option is available only if multiple CPUs are available on the specified slot.

statistics: Displays statistics for the multicast forwarding table.

Examples

# Display multicast forwarding entries on an ADVPN network.

<Sysname> display multicast forwarding-table

Total 1 entries, 1 matched

00001. (172.168.0.2, 227.0.0.1)

Flags: 0x0

Uptime: 00:08:32, Timeout in: 00:03:26

Incoming interface: Tunnel1, 12.1.1.3

List of 2 outgoing interface:

1: Tunnel1, 12.1.1.1

2: Tunnel1, 12.1.1.2

Matched 19648 packets(20512512 bytes), Wrong If 0 packet

Forwarded 19648 packets(20512512 bytes)

# Display multicast forwarding entries on the public network.

<Sysname> display multicast forwarding-table

Total 1 entries, 1 matched

00001. (172.168.0.2, 227.0.0.1)

Flags: 0x0

Uptime: 00:08:32, Timeout in: 00:03:26

Incoming interface: Vlan-interface10

List of 1 outgoing interfaces:

1: Vlan-interface20

Matched 19648 packets(20512512 bytes), Wrong If 0 packet

Forwarded 19648 packets(20512512 bytes)

Table 6 Command output

Field	Description
Total 1 entries, 1 matched	Total number of (S, G) entries, and the total number of matching (S, G) entries.
00001	Sequence number of the (S, G) entry.
(172.168.0.2,227.0.0.1)	(S, G) entry.
Flags	Entry flag. This field displays one flag or the sum of multiple flags. In this example, the value 0x0 means that the entry has only one flag 0x0. The following entries are available for an entry: · 0x0—The entry is in correct state. · 0x1—The entry is in inactive state. · 0x2—The entry is null. · 0x4—The entry fails to update. · 0x8—Outgoing interface information fails to update for the entry. · 0x10—Data-group information fails to update for the entry. · 0x20—A register outgoing interface is available. · 0x40—The entry is to be deleted. · 0x80—The entry is in registration suppression state. · 0x100—The entry is being deleted. · 0x200—The entry is in GR state. · 0x800—The entry has the associated ARP entry for the multicast source address. · 0x400000—The entry is created by the IGMP proxy. · 0x2000000—The entry is a BIDIR-PIM forwarding entry.
Uptime	Length of time for which the (S, G) entry has been up.
Timeout in	Length of time in which the (S, G) entry will expire.
Incoming interface	Incoming interface of the (S, G) entry.
List of 1 outgoing interfaces	Outgoing interface list of the (S, G) entry.
Tunnel1, 12.1.1.1	ADVPN tunnel interface, and the IP address of the remote end.
Matched 19648 packets(20512512 bytes), Wrong If 0 packet	Number of packets (bytes) that match the (S, G) entry, and number of packets with incoming interface errors. The numbers are displayed as 0 if an outgoing interface of the (S, G) entry is on the specified slot.
Forwarded 19648 packets(20512512 bytes)	Number of packets (bytes) that have been forwarded. The numbers are displayed as 0 if an outgoing interface of the (S, G) entry is on the specified slot.

Related commands

reset multicast forwarding-table

display multicast forwarding-table df-list

Use display multicast forwarding-table df-list to display information about the DF list in multicast forwarding entries.

Syntax

In standalone mode:

display multicast [ vpn-instance vpn-instance-name ] forwarding-table df-list [ group-address ] [ verbose ] [ slot slot-number [ cpu cpu-number ] ]

In IRF mode:

display multicast [ vpn-instance vpn-instance-name ] forwarding-table df-list [ group-address ] [ verbose ] [ chassis chassis-number slot slot-number [ cpu cpu-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

vsys-admin

vsys-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays information about the DF list in multicast forwarding entries on the public network.

group-address: Specifies a multicast group address in the range of 224.0.0.0 to 239.255.255.255.

verbose: Specifies detailed information about the DF list in multicast forwarding entries. If you do not specify this keyword, the command displays brief information about the DF list in multicast forwarding entries.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays information about the DF list in multicast forwarding entries for the MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify a card, this command displays information about the DF list in multicast forwarding entries for the global active MPU. (In IRF mode.)

cpu cpu-number: Specifies a CPU by its number. This option is available only if multiple CPUs are available on the specified slot.

Examples

# Display brief information about the DF list in multicast forwarding entries on the public network.

<Sysname> display multicast forwarding-table df-list

Total 1 entries, 1 matched

00001. (0.0.0.0, 225.0.0.1)

List of 1 DF interfaces:

1: GigabitEthernet1/0/1

# Display detailed information about the DF list in multicast forwarding entries on the public network.

<Sysname> display multicast forwarding-table df-list verbose

Total 1 entries, 1 matched

00001. (0.0.0.0, 225.0.0.1)

List of 1 DF interfaces:

1: GigabitEthernet1/0/1

Product information: 0x347849f6, 0x14bd6837

Tunnel information: 0xc4857986, 0x128a9c8f

Table 7 Command output

Field	Description
Total 1 entries, 1 matched	Total number of forwarding entries, and the total number of matching entries.
00001	Sequence number of the entry.
(0.0.0.0, 225.0.0.1)	(*, G) entry.
List of 1 DF interfaces	DF interface list.

display multicast routing-table

Use display multicast routing-table to display multicast routing entries.

Syntax

display multicast [ vpn-instance vpn-instance-name ] routing-table [ source-address [ mask { mask-length | mask } ] | group-address [ mask { mask-length | mask } ] | incoming-interface interface-type interface-number | outgoing-interface { exclude | include | match } interface-type interface-number ] *

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

vsys-admin

vsys-operator

Parameters

source-address: Specifies a multicast source address.

group-address: Specifies a multicast group address in the range of 224.0.0.0 to 239.255.255.255.

mask: Specifies an address mask. The default is 255.255.255.255.

incoming-interface: Specifies the multicast routing entries that contain the specified incoming interface.

interface-type interface-number: Specifies an interface by its type and number.

outgoing-interface: Specifies the multicast routing entries that contain the specified outgoing interface.

exclude: Specifies the multicast routing entries that do not contain the specified interface in the outgoing interface list.

include: Specifies the multicast routing entries that contain the specified interface in the outgoing interface list.

match: Specifies the multicast routing entries that contain only the specified interface in the outgoing interface list.

Usage guidelines

Multicast routing entries are the basis of multicast forwarding. You can use this command to view the establishment state of (S, G) entries.

Examples

# Display multicast routing entries on an ADVPN network.

<Sysname> display multicast routing-table

Total 1 entries

00001. (172.168.0.2, 227.0.0.1)

Uptime: 00:00:28

Upstream Interface: Tunnel1, 12.1.1.3

List of 2 downstream interfaces

1: Tunnel1, 12.1.1.1

2: Tunnel1, 12.1.1.2

# Display multicast routing entries on the public network.

<Sysname> display multicast routing-table

Total 1 entries

00001. (172.168.0.2, 227.0.0.1)

Uptime: 00:00:28

Upstream Interface: GigabitEthernet1/0/1

List of 2 downstream interfaces

1: GigabitEthernet1/0/2

2: GigabitEthernet1/0/3

Table 8 Command output

Field	Description
Total 1 entries	Total number of (S, G) entries.
00001	Sequence number of the (S, G) entry.
(172.168.0.2, 227.0.0.1)	(S, G) entry.
Uptime	Length of time for which the (S, G) entry has been up.
Upstream Interface	Upstream interface at which (S, G) packets should arrive.
List of 2 downstream interfaces	List of downstream interfaces that need to forward (S, G) packets.
Tunnel1, 12.1.1.1	ADVPN tunnel interface, and the IP address of the remote end.

Related commands

reset multicast routing-table

display multicast routing-table static

Use display multicast routing-table static to display static multicast routing entries.

Syntax

display multicast [ vpn-instance vpn-instance-name ] routing-table static [ source-address { mask-length | mask } ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays static multicast routing entries on the public network.

source-address: Specifies a multicast source address.

mask-length: Specifies an address mask length in the range of 0 to 32.

mask: Specifies an address mask.

Usage guidelines

Non-default vSystems do not support this command.

This command displays only valid static multicast routing entries.

Examples

# Display static multicast routing entries on the public network.

<Sysname> display multicast routing-table static

Destinations: 3 Routes: 4

Destination/Mask Pre RPF neighbor Interface

1.1.0.0/16 10 7.12.0.1 GE1/0/1

7.11.0.1 GE1/0/2

2.2.2.0/24 20 7.11.0.1 GE1/0/3

3.3.3.3/32 50 7.12.0.1 GE1/0/4

Table 9 Command output

Field	Description
Destinations	Number of the multicast destination addresses.
Routes	Number of routes.
Destination/Mask	Destination address and its mask length.
Pre	Route preference.
RPF neighbor	IP address of the RPF neighbor to the reachable destination.
Interface	Outgoing interface to the reachable destination.

display multicast rpf-info

Use display multicast rpf-info to display RPF information for a multicast source.

Syntax

display multicast [ vpn-instance vpn-instance-name ] rpf-info source-address [ group-address ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

vsys-admin

vsys-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays RPF information for a multicast source on the public network.

source-address: Specifies a multicast source address.

group-address: Specifies a multicast group address in the range of 224.0.1.0 to 239.255.255.255.

Examples

# Display RPF information for multicast source 192.168.1.55 on the public network.

<Sysname> display multicast rpf-info 192.168.1.55

RPF information about source 192.168.1.55:

RPF interface: GigabitEthernet1/0/1, RPF neighbor: 10.1.1.1

Referenced route/mask: 192.168.1.0/24

Referenced route type: igp

Route selection rule: preference-preferred

Load splitting rule: disable

Source AS: 0

C-multicast route target: 0x0000000000000000

Table 10 Command output

Field	Description
RPF neighbor	IP address of the RPF neighbor.
Referenced route/mask	Referenced route and its mask length.
Referenced route type	Type of the referenced route: · igp—IGP unicast route. · egp—EGP unicast route. · unicast (direct)—Directly connected unicast route. · unicast—Other unicast routes, such as static unicast route. · multicast static—Static multicast route. · mbgp—MBGP route.
Route selection rule	Rule for RPF route selection: · Route preference. · Longest prefix match.
Load splitting rule	Status of the load splitting rule: enable or disable.
Source AS	AS number of the source-side PE.
C-multicast route target	Route target attribute value of the C-multicast route.

Related commands

display multicast forwarding-table

display multicast routing-table

ip rpf-route-static

Use ip rpf-route-static to configure a static multicast route.

Use undo ip rpf-route-static to delete a static multicast route.

Syntax

ip rpf-route-static [ vpn-instance vpn-instance-name ] source-address { mask-length | mask } { rpf-nbr-address | interface-type interface-number } [ preference preference ]

undo ip rpf-route-static [ vpn-instance vpn-instance-name ] source-address { mask-length | mask } { rpf-nbr-address | interface-type interface-number }

Default

No static multicast routes exist.

Views

System view

Predefined user roles

network-admin

context-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command configures a static multicast route on the public network.

source-address: Specifies a multicast source address.

mask-length: Specifies an address mask length in the range of 0 to 32.

mask: Specifies an address mask.

rpf-nbr-address: Specifies an RPF neighbor by its IP address.

interface-type interface-number: Specifies an interface by its type and number. The interface connects the RPF neighbor.

preference: Sets a route preference in the range of 1 to 255. The default value is 1.

Usage guidelines

Non-default vSystems do not support this command.

If the interface connected to an RPF neighbor is a point-to-point interface, you must specify the interface by its type and number.

If the interface connected to an RPF neighbor is not a point-to-point interface, you must specify the interface by its IP address. This type of interfaces includes Layer 3 Ethernet, Layer 3 aggregate, Loopback, and VLAN interfaces.

The configured static multicast route might not take effect when one of the following conditions exists:

· The outgoing interface iteration fails.

· The specified interface is not in the public network or the same VPN instance as the current interface.

· The specified interface is not a point-to-point interface.

· The specified interface is down.

If multiple static multicast routes within the same multicast source address range are available, only the one with the highest route preference can become active. You can use the display multicast routing-table static command to verify that the configured static multicast route has taken effect.

The undo ip rpf-route-static command deletes the specified static multicast route, but the delete ip rpf-route-static command deletes all static multicast routes.

Examples

# Configure a static multicast route to multicast source 10.1.1.0/24 and specify the interface with IP address 192.168.1.23 as the RPF neighbor on the public network.

<Sysname> system-view

[Sysname] ip rpf-route-static 10.1.1.0 24 192.168.1.23

Related commands

delete ip rpf-route-static

display multicast routing-table static

load-splitting (MRIB view)

Use load-splitting to enable multicast load splitting.

Use undo load-splitting to restore the default.

Syntax

load-splitting { source | source-group }

undo load-splitting

Default

Multicast load splitting is disabled.

Views

MRIB view

Predefined user roles

network-admin

context-admin

Parameters

source: Enables multicast load splitting based on multicast source.

source-group: Enables multicast load splitting based on multicast source and group.

Usage guidelines

Non-default vSystems do not support this command.

This command does not take effect on BIDIR-PIM.

Examples

# Enable multicast load splitting based on multicast source on the public network.

<Sysname> system-view

[Sysname] multicast routing

[Sysname-mrib] load-splitting source

longest-match (MRIB view)

Use longest-match to specify the longest prefix match principle for RPF route. The device will use the matching route with the longest prefix as the RPF route.

Use undo longest-match to restore the default.

Syntax

longest-match

undo longest-match

Default

Route preference is used for RPF route selection. The route with the highest preference is used as the RPF route.

Views

MRIB view

Predefined user roles

network-admin

context-admin

Usage guidelines

Non-default vSystems do not support this command.

Examples

# Specify the longest prefix match principle for RPF route selection on the public network.

<Sysname> system-view

[Sysname] multicast routing

[Sysname-mrib] multicast longest-match

multicast-broadcast forwarding-mode per-packet

Use multicast-broadcast forwarding-mode per-packet to configure the per-packet load balancing mode for multicast and broadcast traffic to CPUs.

Use undo multicast-broadcast forwarding-mode per-packet to configure the per-flow load balancing mode for multicast and broadcast traffic to CPUs.

Syntax

multicast-broadcast forwarding-mode per-packet

undo multicast-broadcast forwarding-mode per-packet

The following compatibility matrix shows the support of hardware platforms for this command:

Hardware platform	Module type	Command compatibility
M9006 M9010 M9014	Blade IV firewall module	Yes
	Blade V firewall module	No
	NAT module	Yes
M9010-GM	Encryption module	Yes
M9016-V	Blade V firewall module	No
M9008-S M9012-S	Blade IV firewall module	Yes
	Intrusion prevention service (IPS) module	Yes
	Video network gateway module	Yes
M9008-S-V	Blade IV firewall module	Yes
M9000-AI-E4 M9000-AI-E8 M9000-AI-E16	Blade V firewall module	Yes
M9000-AK001	Blade V firewall module	Yes
M9000-X06 M9000-X06-B M9000-X06-B-G M9000-X06-G M9000-X10	Blade VI firewall module	No
M9000-AI-X06 M9000-AI-X10	Blade VI firewall module	No

‌

Default

The load balancing mode for multicast and broadcast traffic to CPUs is per-packet mode.

Views

System view

Predefined user roles

network-admin

Usage guidelines

A multi-CPU device will distribute incoming multicast and broadcast traffic to different CPUs for load balancing. The following load balancing modes are supported:

· Per-packet mode—The device distributes the multicast and broadcast traffic to CPUs packet by packet. In this mode, the packets arrive first might not be processed first.

· Per-flow mode—The device distributes the multicast and broadcast traffic to CPUs on a per-flow basis. The same flow might be distributed to one or more CPUs. Packets with the same source IP address, source port number, destination IP address, destination port number, and protocol number belong to the same flow. In this mode, the packets arrive first are processed first.

For packets arriving at the CPU first to be processed first, configure the per-flow mode.

Examples

# Configure the per-packet load balancing mode for multicast and broadcast traffic to CPUs.

<Sysname> system-view

[Sysname] multicast-broadcast forwarding-mode per-packet

multicast boundary

Use multicast boundary to configure a multicast forwarding boundary.

Use undo multicast boundary to delete a multicast forwarding boundary.

Syntax

multicast boundary group-address { mask-length | mask }

undo multicast boundary { group-address { mask-length | mask } | all }

Default

No multicast forwarding boundaries are configured on an interface.

Views

Interface view

Predefined user roles

network-admin

context-admin

Parameters

group-address: Specifies a multicast group address in the range of 224.0.0.0 to 239.255.255.255.

mask-length: Specifies an address mask length in the range of 4 to 32.

mask: Specifies an address mask.

all: Specifies all forwarding boundaries configured on the interface.

Usage guidelines

Non-default vSystems do not support this command.

A multicast forwarding boundary sets the boundary condition for the multicast groups in the specified address range. If the destination address of a multicast packet matches the set boundary condition, the packet is not forwarded.

You can configure an interface as a multicast forwarding boundary for different multicast group ranges by executing this command multiple times on the interface.

You do not need to enable IP multicast routing before you execute this command.

Assume that Set A and Set B are multicast forwarding boundary sets with different address ranges, and B is a subset of A. A takes effect on the interface no matter whether A is configured earlier or later than B.

Examples

# Configure GigabitEthernet 1/0/1 as the forwarding boundary of multicast groups in the range of 239.2.0.0/16.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] multicast boundary 239.2.0.0 16

Related commands

display multicast boundary

multicast forwarding-table cache-unknown per-entry

Use multicast forwarding-table cache-unknown per-entry to set the maximum number of unknown multicast packets that can be cached for an (S, G) entry.

Use undo multicast forwarding-table cache-unknown per-entry to restore the default.

Syntax

multicast forwarding-table cache-unknown per-entry per-entry-limit

undo multicast forwarding-table cache-unknown per-entry

Default

The device can cache only one unknown multicast packet for an (S, G) entry.

Views

System view

Predefined user roles

network-admin

context-admin

Parameters

per-entry-limit: Specifies the maximum number of unknown multicast packets that can be cached for an (S, G) entry. The value range for this argument is 0 to 256. If you set the value to 0, the device cannot cache unknown multicast packets.

Usage guidelines

Non-default vSystems do not support this command.

Examples

# Set the maximum number to 20 for unknown multicast packets that can be cached for an (S, G) entry.

<Sysname> system-view

[Sysname] multicast forwarding-table cache-unknown per-entry 20

Related commands

multicast forwarding-table cache-unknown total

Use multicast forwarding-table cache-unknown total to set the maximum number of all unknown multicast packets that can be cached.

Use undo multicast forwarding-table cache-unknown total to restore the default.

Syntax

multicast forwarding-table cache-unknown total total-limit

undo multicast forwarding-table cache-unknown total

Default

The device can cache 1024 unknown multicast packets in total.

Views

System view

Predefined user roles

network-admin

context-admin

Parameters

total-limit: Specifies the maximum number of all unknown multicast packets that can be cached. The value range for this argument is 0 to 65535. If you set the value to 0, the device cannot cache unknown multicast packets.

Usage guidelines

As a best practice, set the value in this command to be far greater than the value set in the multicast forwarding-table cache-unknown per-entry command.

Examples

# Set the maximum number to 10000 for all unknown multicast packets that can be cached.

<Sysname> system-view

[Sysname] multicast forwarding-table cache-unknown total 10000

Related commands

multicast forwarding-table cache-unknown per-entry

multicast routing

Use multicast routing to enable IP multicast routing and enter MRIB view.

Use undo multicast routing to disable IP multicast routing.

Syntax

multicast routing [ vpn-instance vpn-instance-name ]

undo multicast routing [ vpn-instance vpn-instance-name ]

Default

IP multicast routing is disabled.

Views

System view

Predefined user roles

network-admin

context-admin

vsys-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command enables IP multicast routing on the public network.

Usage guidelines

Other Layer 3 multicast commands take effect only when IP multicast routing is enabled on the public network or for a VPN instance.

The device does not forward multicast packets before IP multicast routing is enabled.

Examples

# Enable IP multicast routing on the public network, and enter MRIB view.

<Sysname> system-view

[Sysname] multicast routing

[Sysname-mrib]

# Enable IP multicast routing for the VPN instance mvpn, and enter MRIB view.

<Sysname> system-view

[Sysname] multicast routing vpn-instance mvpn

[Sysname-mrib-mvpn]

reset multicast fast-forwarding cache

Use reset multicast fast-forwarding cache to clear multicast fast forwarding entries.

Syntax

In standalone mode:

reset multicast [ vpn-instance vpn-instance-name ] fast-forwarding cache { { source-address | group-address } * | all } [ slot slot-number [ cpu cpu-number ] ]

In IRF mode:

reset multicast [ vpn-instance vpn-instance-name ] fast-forwarding cache { { source-address | group-address } * | all } [ chassis chassis-number slot slot-number [ cpu cpu-number ] ]

Views

User view

Predefined user roles

network-admin

context-admin

vsys-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command clears multicast fast forwarding entries on the public network.

source-address: Specifies a multicast source address.

group-address: Specifies a multicast group address in the range of 224.0.0.0 to 239.255.255.255.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command clears multicast fast forwarding entries for the MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify a card, this command clears multicast fast forwarding entries for the global active MPU. (In IRF mode.)

cpu cpu-number: Specifies a CPU by its number. This option is available only if multiple CPUs are available on the specified slot.

all: Specifies all multicast fast forwarding entries.

Examples

# Clear all multicast fast forwarding entries on the public network.

<Sysname> reset multicast fast-forwarding cache all

# Clear the multicast fast forwarding entry for multicast source and group (20.0.0.2, 225.0.0.2) on the public network.

<Sysname> reset multicast fast-forwarding cache 20.0.0.2 225.0.0.2

Related commands

display multicast fast-forwarding cache

reset multicast forwarding event

Use reset multicast forwarding event to clear statistics for multicast forwarding events.

Syntax

reset multicast [ vpn-instance vpn-instance-name ] forwarding event

Views

User view

Predefined user roles

network-admin

context-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command clears statistics for the multicast forwarding events on the public network.

Usage guidelines

Non-default vSystems do not support this command.

Examples

# Clear statistics for multicast forwarding events on the public network.

<Sysname> reset multicast forwarding event

Related commands

display multicast forwarding event

reset multicast forwarding-table

Use reset multicast forwarding-table to clear multicast forwarding entries.

Syntax

reset multicast [ vpn-instance vpn-instance-name ] forwarding-table { { source-address [ mask { mask-length | mask } ] | group-address [ mask { mask-length | mask } ] | incoming-interface { interface-type interface-number } } * | all }

Views

User view

Predefined user roles

network-admin

context-admin

Parameters

source-address: Specifies a multicast source address.

group-address: Specifies a multicast group address in the range of 224.0.0.0 to 239.255.255.255.

mask: Specifies an address mask. The default is 255.255.255.255.

incoming-interface: Specifies the multicast forwarding entries that contain the specified incoming interface.

interface-type interface-number: Specifies an incoming interface by its type and number.

all: Specifies all multicast forwarding entries.

Usage guidelines

Non-default vSystems do not support this command.

When you clear a multicast forwarding entry, the associated multicast routing entry is also cleared.

Examples

# Clear multicast forwarding entries for multicast group 225.5.4.3 on the public network.

<Sysname> reset multicast forwarding-table 225.5.4.3

Related commands

display multicast forwarding-table

reset multicast routing-table

Use reset multicast routing-table to clear multicast routing entries.

Syntax

reset multicast [ vpn-instance vpn-instance-name ] routing-table { { source-address [ mask { mask-length | mask } ] | group-address [ mask { mask | mask-length } ] | incoming-interface interface-type interface-number } * | all }

Views

User view

Predefined user roles

network-admin

context-admin

Parameters

source-address: Specifies a multicast source address.

group-address: Specifies a multicast group address in the range of 224.0.0.0 to 239.255.255.255.

mask: Specifies an address mask. The default is 255.255.255.255.

incoming-interface: Specifies the routing entries that contain the specified incoming interface.

interface-type interface-number: Specifies an incoming interface by its type and number.

all: Specifies all multicast routing entries.

Usage guidelines

Non-default vSystems do not support this command.

When you clear a multicast routing entry, the associated multicast forwarding entry is also cleared.

Examples

# Clear multicast routing entries for multicast group 225.5.4.3 on the public network.

<Sysname> reset multicast routing-table 225.5.4.3

Related commands

display multicast routing-table

14-IP Multicast Command Reference

display mrib interface

display multicast forwarding event

reset multicast fast-forwarding cache

reset multicast routing-table

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

News & Events

Contact Us