Non-default vSystems do not support some of the Ethernet link aggregation commands. For information about vSystem support for a command, see the usage guidelines on that command. For information about vSystem, see Virtual Technologies Configuration Guide.

bandwidth

Use bandwidth to set the expected bandwidth for an interface.

Use undo bandwidth to restore the default.

Syntax

bandwidth bandwidth-value

undo bandwidth

Default

The expected bandwidth (in kbps) is the interface baud rate divided by 1000.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

Predefined user roles

network-admin

context-admin

vsys-admin

Parameters

bandwidth-value: Specifies the expected bandwidth in the range of 1 to 400000000 kbps.

Usage guidelines

The expected bandwidth is an informational parameter used only by higher-layer protocols for calculation. You cannot adjust the actual bandwidth of an interface by using this command.

Examples

# Set the expected bandwidth to 10000 kbps for Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] bandwidth 10000

# Set the expected bandwidth to 10000 kbps for Layer 3 aggregate interface Route-Aggregation 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] bandwidth 10000

default

Use default to restore the default settings for an aggregate interface.

Syntax

default

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

Predefined user roles

network-admin

context-admin

Usage guidelines

CAUTION:

The default command might interrupt ongoing network services. Make sure you are fully aware of the impacts of this command when you execute it on a live network.

Non-default vSystems do not support this command.

This command might fail to restore the default settings for some commands for reasons such as command dependencies and system restrictions. Use the display this command in interface view to identify these commands, and then use their undo forms or follow the command reference to restore their default settings. If your restoration attempt still fails, follow the error message instructions to resolve the problem.

Examples

# Restore the default settings for Layer 2 aggregate interface 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] default

# Restore the default settings for Layer 3 aggregate interface 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] default

description

Use description to configure the description of an interface.

Use undo description to restore the default.

Syntax

description text

undo description

Default

The description of an interface is interface-name Interface. For example, the default description of Bridge-Aggregation 1 is Bridge-Aggregation1 Interface.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

Predefined user roles

network-admin

context-admin

vsys-admin

Parameters

text: Specifies a description, a case-sensitive string of 1 to 255 characters.

Examples

# Configure the description as connect to the lab for Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] description connect to the lab

# Configure the description as connect to the lab for Layer 3 aggregate interface Route-Aggregation 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] description connect to the lab

display interface

Use display interface to display aggregate interface information.

Syntax

display interface [ { blade-aggregation | bridge-aggregation | route-aggregation } [ interface-number ] ] [ brief [ description | down ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

vsys-admin

vsys-operator

Parameters

blade-aggregation: Specifies Blade aggregate interfaces.

bridge-aggregation: Specifies Layer 2 aggregate interfaces.

route-aggregation: Specifies Layer 3 aggregate interfaces.

interface-number: Specifies an existing aggregate interface number.

brief: Displays brief interface information. If you do not specify this keyword, the command displays detailed interface information.

description: Displays complete interface descriptions. If you do not specify this keyword, the command displays only the first 27 characters of each interface description.

down: Displays information about interfaces in down state and the causes for the down state. If you do not specify this keyword, the command displays information about interfaces in all states.

Usage guidelines

If you do not specify an aggregate interface type, this command displays information about all interfaces except VA interfaces. For more information about VA interfaces, see PPP configuration in PPP and PPPoE Configuration Guide.

If you specify an aggregate interface type but do not specify an interface number, this command displays information about all aggregate interfaces of the specified type.

Examples

# Display detailed information about Blade aggregate interface Blade-Aggregation 1.

<Sysname> display interface blade-aggregation 1

Blade-Aggregation1

Current state: DOWN

IP packet frame type: Ethernet II, hardware address: 0023-89bb-3dcc

Description: Blade-Aggregation1 Interface

Unknown-speed mode, unknown-duplex mode

Link speed type is autonegotiation, link duplex type is autonegotiation

Last clearing of counters: Never

Last 300 seconds input: 0 packets/sec 0 bytes/sec 0%

Last 300 seconds output: 0 packets/sec 0 bytes/sec 0%

Input (total): 0 packets, 0 bytes

0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses

Input (normal): 0 packets, 0 bytes

0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses

Input: 0 input errors, 0 runts, 0 giants, 0 throttles

0 CRC, 0 frame, 0 overruns, 0 aborts

0 ignored, 0 parity errors

Output (total): 0 packets, 0 bytes

0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses

Output (normal): 0 packets, 0 bytes

0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses

Output: 0 output errors, 0 underruns, 0 buffer failures

0 aborts, 0 deferred, 0 collisions, 0 late collisions

0 lost carrier, 0 no carrier

# Display detailed information about Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> display interface bridge-aggregation 1

Bridge-Aggregation1

Current state: UP

IP packet frame type: Ethernet II, hardware address: 000f-e207-f2e0

Description: Bridge-Aggregation1 Interface

Bandwidth: 1000 kbps

2Gbps-speed mode, full-duplex mode

Link speed type is autonegotiation, link duplex type is autonegotiation

PVID: 1

Port link-type: Access

Tagged VLANs: None

UnTagged VLANs: 1

Last clearing of counters: Never

Last 300 seconds input: 6900 packets/sec 885160 bytes/sec 0%

Last 300 seconds output: 3150 packets/sec 404430 bytes/sec 0%

Input (total): 5364747 packets, 686688416 bytes

2682273 unicasts, 1341137 broadcasts, 1341337 multicasts, 0 pauses

Input (normal): 5364747 packets, 686688416 bytes

2682273 unicasts, 1341137 broadcasts, 1341337 multicasts, 0 pauses

Input: 0 input errors, 0 runts, 0 giants, 0 throttles

0 CRC, 0 frame, 0 overruns, - aborts

- ignored, - parity errors

Output (total): 1042508 packets, 133441832 bytes

1042306 unicasts, 0 broadcasts, 202 multicasts, - pauses

Output (normal): 1042508 packets, 133441832 bytes

1042306 unicasts, 0 broadcasts, 202 multicasts, 0 pauses

Output: 0 output errors, - underruns, - buffer failures

0 aborts, 0 deferred, 0 collisions, 0 late collisions

- lost carrier, - no carrier

# Display detailed information about Layer 3 aggregate interface Route-Aggregation 1.

<Sysname> display interface route-aggregation 1

Route-Aggregation1

Current state: UP

Line protocol state: UP

Description: Route-Aggregation1 Interface

Bandwidth: 1000 kbps

Maximum transmission unit: 1500

Internet protocol processing: Disabled

IP packet frame type: Ethernet II, hardware address: 0000-0000-0000

IPv6 packet frame type: Ethernet II, hardware address: 0000-0000-0000

Link speed type is autonegotiation, link duplex type is autonegotiation

Last clearing of counters: Never

Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Input: 0 packets, 0 bytes, 0 drops

Output: 0 packets, 0 bytes, 0 drops

# Display brief information about Blade aggregate interface Blade-Aggregation 1.

<Sysname> display interface blade-aggregation 1 brief

Brief information on interfaces in bridge mode:

Link: ADM - administratively down; Stby - standby

Speed: (a) – auto

Duplex: (a)/A - auto; H - half; F - full

Type: A - access; T - trunk; H - hybrid

Interface Link Speed Duplex Type PVID Description

BLAGG1 DOWN 10G F -- --

# Display brief information about Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> display interface bridge-aggregation 1 brief

Brief information on interfaces in bridge mode:

Link: ADM - administratively down; Stby - standby

Speed: (a) – auto

Duplex: (a)/A - auto; H - half; F - full

Type: A - access; T - trunk; H - hybrid

Interface Link Speed Duplex Type PVID Description

BAGG1 UP auto A A 1

# Display brief information about Layer 3 aggregate interface Route-Aggregation 1.

<Sysname> display interface route-aggregation 1 brief

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface Link Protocol Primary IP Description

RAGG1 UP UP --

Table 1 Command output

Field	Description
Blade-Aggregation1	Blade aggregate interface name.
Bridge-Aggregation1	Layer 2 aggregate interface name.
Route-Aggregation1	Layer 3 aggregate interface name.
Current state	Physical link state of the interface: · Administratively DOWN—The interface has been shut down by using the shutdown command. · DOWN—The interface is administratively up, but its physical state is down (possibly because no physical link exists or the link has failed). · UP—The interface is both administratively and physically up.
IP packet frame type	IPv4 packet framing format.
Description	Description of the interface.
Bandwidth	Expected bandwidth of the interface. This field is not displayed when the bandwidth is 0 kbps.
Port priority	Port priority of the interface.
Unknown-speed mode, unknown-duplex mode	The interface speed and duplex mode are unknown.
Port link-type	Port link type: · Access. · Trunk. · Hybrid.
Tagged VLANs	VLAN whose packets are sent out of this interface with a tag.
Untagged VLANs	VLAN whose packets are sent out of this interface without a tag.
Last clearing of counters	Time when the reset counters interface command was last used to clear the interface statistics. This field displays Never if the reset counters interface command has never been used on the interface since device startup.
Last 300 seconds input/output rate	Average input or output rate over the last 300 seconds.
Input/Output (total)	Statistics of all packets received or sent on the interface.
Input/Output (normal)	Statistics of all normal packets received or sent on the interface.
Line protocol state	Data link layer state of the interface: · UP. · DOWN.
Maximum transmission unit	MTU of the interface.
Internet protocol processing: Disabled	The interface is not assigned an IP address and cannot process IP packets.
Internet address: ip-address/mask-length (Type)	IP address of the interface and type of the address in parentheses. Possible IP address types include: · Primary—Manually configured primary IP address. · Sub—Manually configured secondary IP address. If the interface has both primary and secondary IP addresses, the primary IP address is displayed. If the interface has only secondary IP addresses, the lowest secondary IP address is displayed. · DHCP-Allocated—DHCP allocated IP address. For more information, see DHCP client configuration in Layer 3—IP Services Configuration Guide. · BOOTP-Allocated—BOOTP allocated IP address. For more information, see BOOTP client configuration in Layer 3—IP Services Configuration Guide. · PPP-Negotiated—IP address assigned by a PPP server during PPP negotiation. For more information, see PPP commands in PPP and PPPoE Command Reference. · Unnumbered—IP address borrowed from another interface. · MAD—IP address assigned to an IRF member device for MAD on the interface. For more information, see IRF configuration in Virtual Technologies Configuration Guide.
Brief information on interfaces in route mode	Brief information about Layer 3 interfaces.
Brief information on interfaces in bridge mode	Brief information about Layer 2 interfaces.
Interface	Abbreviated interface name.
Link	Physical link state of the interface: · UP—The interface is physically up. · DOWN—The interface is physically down. · ADM—The interface has been shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command. · Stby—The interface is a backup interface in standby state.
Speed	Speed of the interface, in bps. This field displays the (a) flag next to the speed if the speed is automatically negotiated. This field displays auto if the interface is configured to autonegotiate its speed but the autonegotiation has not started.
Duplex	Duplex mode of the interface: · A—Autonegotiation. The interface is configured to autonegotiate its duplex mode but the autonegotiation has not started. · F—Full duplex. · F(a)—Autonegotiated full duplex. · H—Half duplex. · H(a)—Autonegotiated half duplex.
Type	Link type of the interface: · A—Access. · H—Hybrid. · T—Trunk.
Protocol	Data link layer protocol state of the interface: · UP—The data link layer protocol of the interface is up. · DOWN—The data link layer protocol of the interface is down. · UP(s)—The data link layer protocol of the interface is up, but the link is an on-demand link or does not exist. The (s) attribute represents the spoofing flag. This value is typical of null interfaces and loopback interfaces.
Primary IP	Primary IP address of the interface. This field displays two hyphens (--) if the interface does not have an IP address.
Cause	Cause for the physical link state of an interface to be DOWN.

display lacp system-id

Use display lacp system-id to display the local system ID.

Syntax

display lacp system-id

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

Usage guidelines

Non-default vSystems do not support this command.

You can use the lacp system-priority command to change the LACP priority of the local system. The LACP priority value is specified in decimal format in the lacp system-priority command. However, it is displayed in hexadecimal format in the output from the display lacp system-id command.

Examples

# Display the local system ID.

<Sysname> display lacp system-id

Actor System ID: 0x8000, 0000-fc00-6504

Table 2 Command output

Field	Description
Actor System ID: 0x8000, 0000-fc00-6504	Local system ID, which contains the system LACP priority (0x8000 in this sample output) and the system MAC address (0000-FC00-6504 in this sample output).

Related commands

lacp system-priority

display link-aggregation load-sharing mode

Use display link-aggregation load-sharing mode to display global or group-specific link-aggregation load sharing modes.

Syntax

display link-aggregation load-sharing mode [ interface [ { blade-aggregation | bridge-aggregation | route-aggregation | interface-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

Parameters

blade-aggregation: Specifies Blade aggregate interfaces.

bridge-aggregation: Specifies Layer 2 aggregate interfaces.

route-aggregation: Specifies Layer 3 aggregate interfaces.

interface-number: Specifies an existing aggregate interface number.

Usage guidelines

Non-default vSystems do not support this command.

If you do not specify the interface keyword, the command displays the global link-aggregation load sharing modes.

If you specify the interface keyword, but do not specify an interface, the command displays all group-specific load sharing modes.

The blade-aggregation, bridge-aggregation, or route-aggregation keyword is available only when aggregate interfaces of the corresponding type exist on the device.

Examples

# Display the global link-aggregation load sharing mode. This example displays the default settings.

<Sysname> display link-aggregation load-sharing mode

Link-aggregation load-sharing mode:

Layer 2 traffic: destination-mac address source-mac address

Layer 3 traffic: destination-ip address source-ip address

# Display the global link-aggregation load sharing mode. This example displays user-configured settings.

<Sysname> display link-aggregation load-sharing mode

Link-aggregation load-sharing mode:

destination-mac address, source-mac address

# Display the link-aggregation load sharing mode of Layer 2 aggregation group 1. This example displays the default settings.

<Sysname> display link-aggregation load-sharing mode interface bridge-aggregation 1

Bridge-Aggregation1 load-sharing mode:

Layer 2 traffic: destination-mac address source-mac address

Layer 3 traffic: destination-ip address source-ip address

# Display the link-aggregation load sharing mode of Layer 2 aggregation group 1. This example displays user-configured settings.

<Sysname> display link-aggregation load-sharing mode interface bridge-aggregation 1

Bridge-Aggregation1 load-sharing mode:

destination-mac address, source-mac address

# Display the link-aggregation load sharing mode of Layer 3 aggregation group 1. This example displays the default settings.

<Sysname> display link-aggregation load-sharing mode interface route-aggregation 1

Route-Aggregation1 load-sharing mode:

Layer 2 traffic: destination-mac address source-mac address

Layer 3 traffic: destination-ip address source-ip address

# Display the link-aggregation load sharing mode of Layer 3 aggregation group 1. This example displays user-configured settings.

<Sysname> display link-aggregation load-sharing mode interface route-aggregation 1

Route-Aggregation1 load-sharing mode:

destination-mac address, source-mac address

Table 3 Command output

Field	Description
Link-aggregation load-sharing mode	Global link-aggregation load sharing mode. By default, this field displays the link-aggregation load sharing modes for Layer 2 and Layer 3 traffic. If you have configured the global link-aggregation load sharing mode, this field displays the configured mode.
Bridge-Aggregation1 load-sharing mode	Link-aggregation load sharing mode of Layer 2 aggregation group 1. By default, this field displays the global link-aggregation load sharing modes. If you have configured a link-aggregation load sharing mode for this aggregation group, this field displays the configured mode.
Route-Aggregation1 load-sharing mode	Link-aggregation load sharing mode of Layer 3 aggregation group 1. By default, this field displays the global link-aggregation load sharing modes. If you have configured a link-aggregation load sharing mode for this aggregation group, this field displays the configured mode.
Layer 2 traffic: destination-mac address, source-mac address	Default link-aggregation load sharing mode for Layer 2 traffic. In this sample output, Layer 2 traffic is load shared based on source and destination MAC addresses.
Layer 2 traffic: packet type-based sharing	Default link-aggregation load sharing mode for Layer 2 traffic. In this sample output, the system automatically selects a load sharing mode for Layer 2 traffic.
Layer 3 traffic: destination-ip address, source-ip address	Default link-aggregation load sharing mode for Layer 3 traffic. In this sample output, Layer 3 traffic is load shared based on source and destination IP addresses.
Layer 3 traffic: packet type-based sharing	Default link-aggregation load sharing mode for Layer 3 traffic. In this sample output, the system automatically selects a load sharing mode for Layer 3 traffic.
destination-mac address, source-mac address	User-configured link-aggregation load sharing mode. In this sample output, traffic is load shared based on source and destination MAC addresses.

display link-aggregation load-sharing path

Use display link-aggregation load-sharing path to display forwarding information about the specified traffic flow.

Syntax

In standalone mode:

display link-aggregation load-sharing path interface { bridge-aggregation | route-aggregation } interface-number ingress-port interface-type interface-number [ route ] { { destination-ip ip-address | destination-ipv6 ipv6-address } | { source-ip ip-address | source-ipv6 ipv6-address } | destination-mac mac-address | destination-port port-id | ethernet-type type-number | ip-protocol protocol-id | source-mac mac-address | source-port port-id | vlan vlan-id } * slot slot-number [ cpu cpu-number ]

In IRF mode:

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

Parameters

bridge-aggregation: Specifies Layer 2 aggregate interfaces.

route-aggregation: Specifies Layer 3 aggregate interfaces.

interface-number: Specifies an existing aggregate interface by its number.

ingress-port interface-type interface-number: Specifies an ingress port by its type and number. The ingress port must be a physical port.

route: Displays forwarding information about Layer 3 traffic. If you do not specify this keyword, the command displays forwarding information about Layer 2 traffic.

destination-ip ip-address: Specifies a destination IPv4 address.

destination-ipv6 ipv6-address: Specifies a destination IPv6 address.

source-ip ip-address: Specifies a source IPv4 address.

source-ipv6 ipv6-address: Specifies a source IPv6 address.

destination-mac mac-address: Specifies a destination MAC address in H-H-H format.

destination-port port-id: Specifies a destination port number in the range of 1 to 65535.

ethernet-type type-number: Specifies an Ethernet type code in the range of 1 to 65535.

ip-protocol protocol-id: Specifies an IP protocol by its ID in the range of 0 to 255.

source-mac mac-address: Specifies a source MAC address in H-H-H format.

source-port port-id: Specifies a source port number in the range of 1 to 65535.

vlan vlan-id: Specifies a VLAN by its ID in the range of 1 to 4094.

slot slot-number: Specifies a card by its slot number. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. (In IRF mode.)

cpu cpu-number: Specifies a CPU by its number. This option is available only if multiple CPUs are available on the specified slot.

Usage guidelines

Non-default vSystems do not support this command.

A parameter specified in the command might not be used for selecting the egress port. The Load sharing parameters field displays the parameters that are used in egress port selection. For example, you can specify both the destination-mac mac-address and destination-ip ip-address options. If only the destination MAC address is used for selecting the egress port, the Load sharing parameters field does not display the destination-ip parameter.

If a parameter required for selecting the egress port is not specified, the default value of the parameter is used. If the parameter does not have any default values, the parameter is set to 0.

This command takes effect only on per-flow load sharing and automatic load sharing. As a best practice, do not use this command for per-packet load sharing.

Examples

# (In standalone mode.) Display forwarding information about the specified traffic flow to be sent out of Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> display link-aggregation load-sharing path interface bridge-aggregation 1 ingress-port gigabitethernet 1/0/1 destination-mac 0000-fc00-0001 source-mac 0000-fc00-0002 source-ip 10.100.0.2 destination-ip 10.100.0.1 slot 1

Load sharing mode: destination-mac, source-mac, source-ip, destination-ip

Unspecified parameters are set to 0.

Load-sharing parameters:

Ingress port: GigabitEthernet1/0/1

Destination MAC: 0000-fc00-0001

Source MAC: 0000-fc00-0002

Destination IP: 10.100.0.1

Source IP: 10.100.0.2

Egress port: GigabitEthernet1/0/3

Table 4 Command output

Field	Description
Load sharing mode:	Load sharing mode set for the aggregation group: · destination-mac—Traffic is load shared based on destination MAC addresses. · source-mac—Traffic is load shared based on source MAC addresses. · destination-ip—Traffic is load shared based on destination IP addresses. · source-ip—Traffic is load shared based on source IP addresses. · destination-port—Traffic is load shared based on destination ports. · source-port—Traffic is load shared based on source ports. · ip-protocol—Traffic is load shared based on IP protocol types.
Load sharing parameters	Parameters that are used in egress port selection.
Egress port	Egress port of the specified traffic flow. If no egress port is found, this field displays N/A.

display link-aggregation member-port

Use display link-aggregation member-port to display detailed link aggregation information about the specified member ports.

Syntax

display link-aggregation member-port [ interface-list | auto ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

Parameters

interface-list: Specifies a list of link aggregation member ports, in the format interface-type interface-number1 [ to interface-type interface-number2 ]. The value for the interface-number2 argument must be equal to or greater than the value for the interface-number1 argument.

auto: Specifies all link aggregation member ports that are enabled with automatic assignment.

Usage guidelines

Non-default vSystems do not support this command.

A member port in a static aggregation group cannot obtain information about the peer group. For such member ports, the command displays the port number, port priority, and operational key of only the local end.

Examples

# Display detailed information about GigabitEthernet 1/0/1, which is a member port of a static aggregation group.

<Sysname> display link-aggregation member-port gigabitethernet 1/0/1

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

GigabitEthernet1/0/1:

Aggregate Interface: Bridge-Aggregation1

Port Number: 1

Port Priority: 32768

Oper-Key: 1

# Display detailed information about GigabitEthernet 1/0/2, which is a member port of a dynamic aggregation group.

<Sysname> display link-aggregation member-port gigabitethernet 1/0/2

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

GigabitEthernet1/0/2:

Aggregate Interface: Bridge-Aggregation2

Local:

Port Number: 2

Port Priority: 32768

Oper-Key: 2

Flag: {ACDEF}

Remote:

System ID: 0x8000, 000f-e267-6c6a

Port Number: 26

Port Priority: 32768

Oper-Key: 2

Flag: {ACDEF}

Received LACP Packets: 5 packet(s)

Illegal: 0 packet(s)

Sent LACP Packets: 7 packet(s)

Table 5 Command output

Field	Description
Flags	LACP state flags. This field is one byte long, represented by ABCDEFGH from the least significant bit to the most significant bit. A letter appears when its bit is 1 and does not appear when its bit is 0. · A—Indicates whether LACP is active on the port. 1 indicates active. 0 indicates passive. · B—Indicates the LACP timeout interval. 1 indicates the short timeout interval. 0 indicates the long timeout interval. · C—Indicates whether the sending system considers that the link is aggregatable. 1 indicates yes. 0 indicates no. · D—Indicates whether the sending system considers that the link has been aggregated. 1 indicates yes. 0 indicates no. · E—Indicates whether the sending system considers that the link can collect frames. 1 indicates yes. 0 indicates no. · F—Indicates whether the sending system considers that the link can distribute frames. 1 indicates yes. 0 indicates no. · G—Indicates whether the RX state machine of the sending system is in default state. 1 indicates yes. 0 indicates no. · H—Indicates whether the RX state machine of the sending system is in expired state. 1 indicates yes. 0 indicates no.
Aggregate Interface	Aggregate interface to which the member port belongs.
Local	Information about the local end.
Oper-key	Operational key.
Flag	LACP protocol state flag.
Remote	Information about the peer end.
System ID	Peer system ID, containing the system LACP priority and the system MAC address.
Received LACP Packets	Total number of LACP packets received.
Illegal	Total number of illegal packets.
Sent LACP Packets	Total number of LACP packets sent.

display link-aggregation summary

Use display link-aggregation summary to display brief information about all aggregation groups.

Syntax

display link-aggregation summary

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

Usage guidelines

Non-default vSystems do not support this command.

Static link aggregation groups cannot obtain information about the peer groups. As a result, the Partner ID field displays None or nothing for a static link aggregation group.

Examples

# Display brief information about all aggregation groups.

<Sysname> display link-aggregation summary

Aggregate Interface Type:

BAGG -- Bridge-Aggregation, BLAGG –- Blade-Aggregation, RAGG -- Route-Aggregation

Aggregation Mode: S -- Static, D -- Dynamic

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Actor System ID: 0x8000, 000f-e267-6c6a

AGG AGG Partner ID Selected Unselected Individual Share

Interface Mode Ports Ports Ports Type

--------------------------------------------------------------------------------

BLAGG1 S None 0 0 0 Shar

RAGG1 S None 1 0 0 NonS

BAGG2 D 0x8000,00e0-fcff-ff01 2 0 0 Shar

Table 6 Command output

Field	Description
Aggregate Interface Type	Aggregate interface type: · BAGG—Layer 2. · RAGG—Layer 3. · BLAGG—Blade.
Aggregation Mode	Aggregation group type: · S—Static. · D—Dynamic.
Loadsharing Type	Load sharing type: · Shar—Load-sharing. · NonS—Non-load-sharing.
Actor System ID	Local system ID, which contains the local system LACP priority and the local system MAC address.
AGG Interface	Type and number of the aggregate interface.
AGG Mode	Aggregation group type.
Partner ID	System ID of the peer system, which contains the peer system LACP priority and the peer system MAC address.
Selected Ports	Total number of Selected ports.
Unselected Ports	Total number of Unselected ports.
Individual Ports	Total number of Individual ports.
Share Type	Load sharing type.

display link-aggregation troubleshooting

Use display link-aggregation troubleshooting to display the aggregation states of aggregation member ports and the reason why a port was placed in Unselected state.

Syntax

display link-aggregation troubleshooting [ { bridge-aggregation | route-aggregation | schannel-bundle } [ interface-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

Parameters

bridge-aggregation: Specifies Layer 2 aggregate interfaces.

route-aggregation: Specifies Layer 3 aggregate interfaces.

schannel-bundle: Specifies S-channel bundle interfaces.

interface-number: Specifies an existing aggregate interface by its number.

Usage guidelines

If you do not specify an aggregate interface type, the command displays information about all aggregation groups.

If you specify an aggregate interface type but do not specify an interface number, the command displays information about all aggregation groups of the specified type.

You can specify the bridge-aggregation, route-aggregation, or schannel-bundle keyword only when aggregate interfaces of the specified type exist on the device.

Examples

# Display the aggregation states of aggregation member ports for all aggregation groups and the reason why a port was placed in Unselected state.

<Sysname> display link-aggregation troubleshooting

Aggregate Interface: Bridge-Aggregation2

Member ports:

GE1/0/2

Status: Selected

GE1/0/3

Status: Unselected

Reason: The physical or line protocol state of the port is down

Advice: Check the connection

Table 7 Command output

Field	Description
Reason	Reason why the port was placed in Unselected state.
Advice	Recommended action.

‌

Table 8 Reason why the port was placed in Unselected state

Field
The number of Selected ports had reached the upper limit
Hardware resources were not enough
The number of Selected ports was below the lower limit
The link aggregation configuration of the port was incorrect
The link aggregation configuration of its peer port was incorrect
The physical or line protocol state of the port was down
The port's hardware restriction prevented it from being Selected
The speed configuration of the port was different from that of the reference port
The duplex mode of the port was different from that of the reference port
The port and the aggregate interface had different attribute configurations
The port was in secondary state in a redundancy group
The BFD session state of the port was down
No LACPDU was received by the reference port
The reference port received its own LACPDUs
The link of the port was not aggregatable
The link of the peer port was not aggregatable
The card that hosts the port was absent
The port's operational key was invalid
Link-aggregation traffic redirection was triggered on the local port
The port had not received LACPDUs
The operational key of the peer port was different from that of the reference port
Link-aggregation traffic redirection was triggered on the peer port
The system MAC address of the peer port was different from that of the peer port for the reference port
The peer port did not have the Synchronization flag
The port was in Standby state
Link-aggregation lacp isolate is configured

Table 9 Recommended action

Field
Modify the aggregation group configuration
Release resources
Modify port configuration
Modify peer port configuration
Check the connection
Use another port
Change the port rate to be the same as that of the reference port
Change the port duplex mode to be the same as that of the reference port
Change the port attribute configuration to be the same as that of the aggregate interface
Place the port in primary state in the redundancy group
Check the link that conveys the BFD session
Check whether the peer sends LACPDUs correctly
Check whether the device has a loop
Make sure the card that hosts the port is installed
Check whether the port sends LACPDUs correctly
Change the peer system MAC address to be the same as that of the reference port
Check the LACPDUs sent by the peer
Please check the aggregation state of member ports in a few minutes

display link-aggregation verbose

Use display link-aggregation verbose to display detailed information about the aggregation groups that correspond to the specified aggregate interfaces.

Syntax

display link-aggregation verbose [ { blade-aggregation | bridge-aggregation | route-aggregation } [ interface-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

context-admin

context-operator

Parameters

blade-aggregation: Specifies Blade aggregate interfaces.

bridge-aggregation: Specifies Layer 2 aggregate interfaces.

route-aggregation: Specifies Layer 3 aggregate interfaces.

interface-number: Specifies an existing aggregate interface by its number.

Usage guidelines

Non-default vSystems do not support this command.

If you do not specify an aggregate interface type, the command displays detailed information about all aggregation groups.

If you specify an aggregate interface type but do not specify an interface number, the command displays detailed information about all aggregation groups of the specified type.

The blade-aggregation, bridge-aggregation, or route-aggregation keyword is available only when aggregate interfaces of the corresponding type exist on the device.

Examples

# Display detailed information about Layer 2 aggregation group 1, which is a dynamic aggregation group.

<Sysname> display link-aggregation verbose bridge-aggregation 1

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

Aggregate Interface: Bridge-Aggregation1

Creation Mode: Manual

Aggregation Mode: Dynamic

Loadsharing Type: Shar

System ID: 0x8000, 000f-e267-6c6a

Local:

Port Status Priority Oper-Key Flag

--------------------------------------------------------------------------------

XGE1/2/4/1 S 32768 2 {ACDEF}

XGE1/2/4/2 S 32768 2 {ACDEF}

XGE1/2/4/3 S 32768 2 {ACDEF}

Remote:

Actor Partner Priority Oper-Key SystemID Flag

--------------------------------------------------------------------------------

XGE1/2/4/1 1 32768 2 0x8000, 000f-e267-57ad {ACDEF}

XGE1/2/4/2 1 32768 2 0x8000, 000f-e267-57ad {ACDEF}

XGE1/2/4/3 1 32768 2 0x8000, 000f-e267-57ad {ACDEF}

# Display detailed information about Layer 3 aggregation group 1, which is a dynamic aggregation group.

<Sysname> display link-aggregation verbose route-aggregation 1

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

Aggregate Interface: Route-Aggregation1

Creation Mode: Manual

Aggregation Mode: Dynamic

Loadsharing Type: Shar

System ID: 0x8000, 000f-e267-6c6a

Local:

Port Status Priority Oper-Key Flag

--------------------------------------------------------------------------------

XGE1/2/4/1 S 32768 2 {ACDEF}

XGE1/2/4/2 S 32768 2 {ACDEF}

XGE1/2/4/3 S 32768 2 {ACDEF}

Remote:

Actor Partner Priority Oper-Key SystemID Flag

--------------------------------------------------------------------------------

XGE1/2/4/1 1 32768 2 0x8000, 000f-e267-57ad {ACDEF}

XGE1/2/4/2 1 32768 2 0x8000, 000f-e267-57ad {ACDEF}

XGE1/2/4/3 1 32768 2 0x8000, 000f-e267-57ad {ACDEF}

# Display detailed information about Layer 2 aggregation group 2, which is a static aggregation group.

<Sysname> display link-aggregation verbose bridge-aggregation 2

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

Aggregate Interface: Bridge-Aggregation2

Aggregation Mode: Static

Loadsharing Type: Shar

Port Status Priority Oper-Key

--------------------------------------------------------------------------------

XGE1/2/4/1 S 32768 1

XGE1/2/4/2 S 32768 1

XGE1/2/4/3 S 32768 1

# Display detailed information about Layer 3 aggregation group 2, which is a static aggregation group.

<Sysname> display link-aggregation verbose route-aggregation 2

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

Aggregate Interface: Route-Aggregation2

Aggregation Mode: Static

Loadsharing Type: Shar

Port Status Priority Oper-Key

--------------------------------------------------------------------------------

XGE1/2/4/1 S 32768 1

XGE1/2/4/2 S 32768 1

XGE1/2/4/3 S 32768 1

Table 10 Command output

Field	Description
Loadsharing Type	Load sharing type: · Shar—Load-sharing. · NonS—Non-load-sharing.
Port Status	Port state: · Selected. · Unselected. · Individual.
Port	Port type. Auto port indicates that the port is enabled with automatic assignment.
Flags	LACP state flags. This field is one byte long, represented by ABCDEFGH from the least significant bit to the most significant bit. A letter appears when its bit is 1 and does not appear when its bit is 0. · A—Indicates whether LACP is active on the port. 1 indicates active. 0 indicates passive. · B—Indicates the LACP timeout interval. 1 indicates the short timeout interval. 0 indicates the long timeout interval. · C—Indicates whether the sending system considers that the link is aggregatable. 1 indicates yes. 0 indicates no. · D—Indicates whether the sending system considers that the link has been aggregated. 1 indicates yes. 0 indicates no. · E—Indicates whether the sending system considers that the link can collect frames. 1 indicates yes. 0 indicates no. · F—Indicates whether the sending system considers that the link can distribute frames. 1 indicates yes. 0 indicates no. · G—Indicates whether the RX state machine of the sending system is in default state. 1 indicates yes. 0 indicates no. · H—Indicates whether the RX state machine of the sending system is in expired state. 1 indicates yes. 0 indicates no.
Aggregate Interface	Name of the aggregate interface.
Creation Mode	Creation mode of the dynamic aggregate interface: · Auto. · Manual.
Aggregation Mode	Aggregation group type: · S—Static. · D—Dynamic.
System ID	Local system ID, containing the local system LACP priority and the local system MAC address.
Local	Information about the local end: · Port—Port type and number. · Status—Port state, which can be Selected, Unselected, or Individual. · Priority—Port priority. · Oper-Key—Operational key. · Flag—LACP state flag. NOTE: For static aggregation groups, the Flag field is not displayed.
Remote	Information about the peer end: · Actor—Type and number of the local port. This field displays the (R) flag next to the port if its peer port is the reference port. · Partner—Index of the peer port. · Priority—Priority of the peer port. · Oper-Key—Operational key of the peer port. · System ID—System ID of the peer end. · Flag—LACP state flag of the peer end.

interface blade-aggregation

Use interface blade-aggregation to enter Blade aggregate interface view.

Syntax

interface blade-aggregation interface-number

Default

Blade aggregate interface Blade-Aggregation 1 exists on the device.

Views

System view

Predefined user roles

network-admin

context-admin

Parameters

interface-number: Specifies a Blade aggregate interface number. The value for the interface-number argument can be 1 or 257.

Usage guidelines

Non-default vSystems do not support this command.

A Blade aggregation group can operate only in static mode.

The default Blade aggregate interface Blade-Aggregation 1 cannot be deleted.

Examples

# Enter Blade-Aggregation 1 interface view.

<Sysname> system-view

[Sysname] interface blade-aggregation 1

[Sysname-Blade-Aggregation1]

interface bridge-aggregation

Use interface bridge-aggregation to create a Layer 2 aggregate interface and enter its view, or enter the view of an existing Layer 2 aggregate interface.

Use undo interface bridge-aggregation to delete a Layer 2 aggregate interface.

Syntax

interface bridge-aggregation interface-number

undo interface bridge-aggregation interface-number

Default

No Layer 2 aggregate interfaces exist.

Views

System view

Predefined user roles

network-admin

context-admin

Parameters

interface-number: Specifies a Layer 2 aggregate interface number. The value range for the interface-number argument is 1 to 1024.

Usage guidelines

Non-default vSystems do not support this command.

When you create a Layer 2 aggregate interface, the system automatically creates a Layer 2 aggregation group with the same number. The aggregation group operates in static aggregation mode by default.

Deleting a Layer 2 aggregate interface also deletes the Layer 2 aggregation group. At the same time, the member ports of the aggregation group, if any, leave the aggregation group.

Examples

# Create Layer 2 aggregate interface Bridge-Aggregation 1, and enter its view.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1]

interface route-aggregation

Use interface route-aggregation to create a Layer 3 aggregate interface or subinterface and enter its view, or enter the view of an existing Layer 3 aggregate interface or subinterface.

Use undo interface route-aggregation to delete a Layer 3 aggregate interface or subinterface.

Syntax

interface route-aggregation { interface-number | interface-number.subnumber }

undo interface route-aggregation { interface-number | interface-number.subnumber }

Default

No Layer 3 aggregate interfaces or subinterfaces exist.

Views

System view

Predefined user roles

network-admin

context-admin

vsys-admin

Parameters

interface-number: Specifies a Layer 3 aggregate interface number. The value range for the interface-number argument is 1 to 1024.

interface-number.subnumber: Specifies a subinterface of a Layer 3 aggregate interface. The interface-number argument specifies the main interface number. The subnumber argument specifies the subinterface number and is separated from the main interface number by a dot (.). The value range for the interface-number argument is 1 to 4094.

Usage guidelines

When you create a Layer 3 aggregate interface, the system automatically creates a Layer 3 aggregation group with the same number. The Layer 3 aggregation group operates in static aggregation mode by default.

Deleting a Layer 3 aggregate interface also deletes the Layer 3 aggregation group and all its aggregate subinterfaces. At the same time, the member ports of the aggregation group, if any, leave the aggregation group.

Deleting a Layer 3 aggregate subinterface does not affect the state of the main interface and the corresponding aggregation group.

After you assign a Layer 3 aggregate subinterface to a vSystem, you cannot delete the main interface for the subinterface.

Examples

# Create Layer 3 aggregate interface Route-Aggregation 1 and enter its view.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1]

# Create Layer 3 aggregate subinterface Route-Aggregation 1.1 and enter its view.

<Sysname> system-view

[Sysname] interface route-aggregation 1.1

[Sysname-Route-Aggregation1.1]

jumboframe enable

Use jumboframe enable to allow the jumbo frames on an interface to pass through.

Use undo jumboframe enable to deny jumbo frames on an interface.

Use undo jumboframe enable size to restore the default.

Syntax

jumboframe enable [ size ]

undo jumboframe enable [ size ]

Default

An aggregate interface allows jumbo frames with a maximum length of 9216 bytes to pass through.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

context-admin

Parameters

size: Specifies the maximum length of jumbo frames, in bytes. The value of this argument is fixed at 9216.

Usage guidelines

Non-default vSystems do not support this command.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Allow jumbo frames to pass through on Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> System-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] jumboframe enable

# Allow jumbo frames to pass through on Layer 3 aggregate interface Route-Aggregation 1.

<Sysname> System-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] jumboframe enable

lacp default-selected-port disable

Use lacp default-selected-port disable to disable the default port selection action for dynamic aggregation groups.

Use undo lacp default-selected-port disable to enable the default port selection action for dynamic aggregation groups.

Syntax

lacp default-selected-port disable

undo lacp default-selected-port disable

Default

The default port selection action is enabled for dynamic aggregation groups.

Views

System view

Predefined user roles

network-admin

context-admin

Usage guidelines

Non-default vSystems do not support this command.

The default port selection action applies to dynamic aggregation groups.

This action automatically chooses the port with the lowest ID from among all up member ports as a Selected port if none of them has received LACPDUs before the LACP timeout interval expires.

After this action is disabled, a dynamic aggregation group will not have any Selected ports to forward traffic if it has not received LACPDUs before the LACP timeout interval expires.

Examples

# Disable the default port selection action.

<Sysname> system-view

[Sysname] lacp default-selected-port disable

lacp edge-port

Use lacp edge-port to configure an aggregate interface as an edge aggregate interface.

Use undo lacp edge-port to restore the default.

Syntax

lacp edge-port

undo lacp edge-port

Default

An aggregate interface does not operate as an edge aggregate interface.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

context-admin

Usage guidelines

Non-default vSystems do not support this command.

Use this command on the aggregate interface that connects the device to a server if dynamic link aggregation is configured only on the device. This feature improves link reliability by enabling all member ports of the aggregation group to forward packets.

This command takes effect only on an aggregate interface corresponding to a dynamic aggregation group.

Link-aggregation traffic redirection cannot operate correctly on an edge aggregate interface.

Examples

# Configure Layer 2 aggregate interface Bridge-Aggregation 1 as an edge aggregate interface.

<Sysname> System-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] lacp edge-port

# Configure Layer 3 aggregate interface Route-Aggregation 1 as an edge aggregate interface.

<Sysname> System-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] lacp edge-port

lacp mode

Use lacp mode passive to configure LACP to operate in passive mode on a port.

Use undo lacp mode to restore the default.

Syntax

lacp mode passive

undo lacp mode

Default

LACP operates in active mode on a port.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

context-admin

Usage guidelines

Non-default vSystems do not support this command.

This command takes effect only on member ports of dynamic aggregation groups.

When LACP is operating in passive mode on a local member port and its peer port, both ports cannot send LACPDUs. When LACP is operating in active mode on either end of a link, both ports can send LACPDUs.

Examples

# Configure LACP to operate in passive mode on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lacp mode passive

lacp period short

Use lacp period short to enable the short LACP timeout interval (3 seconds) on an interface.

Use undo lacp period to restore the default.

Syntax

lacp period short

undo lacp period

Default

The LACP timeout interval is the long timeout interval (90 seconds) on an interface.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

context-admin

Usage guidelines

Non-default vSystems do not support this command.

To avoid traffic interruption during an ISSU, do not enable the short LACP timeout interval before performing the ISSU. For more information about ISSU, see Fundamentals Configuration Guide.

Examples

# Enable the short LACP timeout interval (3 seconds) on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lacp period short

lacp system-priority

Use lacp system-priority to set the system LACP priority.

Use undo lacp system-priority to restore the default.

Syntax

lacp system-priority priority

undo lacp system-priority

Default

The system LACP priority is 32768.

Views

System view

Predefined user roles

network-admin

context-admin

Parameters

priority: Specifies the system LACP priority in the range of 0 to 65535. The smaller the value, the higher the system LACP priority.

Usage guidelines

Non-default vSystems do not support this command.

Examples

# Set the system LACP priority to 64.

<Sysname> system-view

[Sysname] lacp system-priority 64

Related commands

link-aggregation port-priority

link-aggregation blade

Use link-aggregation blade to specify a Blade type for a Blade aggregate interface.

Use undo link-aggregation blade to restore the default.

Syntax

link-aggregation blade blade-type

undo link-aggregation blade

Views

Blade aggregate interface

Predefined user roles

network-admin

context-admin

Parameters

blade-type: Specifies a Blade type. The value for this argument can be Blade4fw, Blade5fw, or Blade6fw.

Usage guidelines

CAUTION:

When you specify a Blade type for the Blade aggregate interface, make sure the type matches that of each Blade interface in the Blade aggregation group. If a mismatch exists, it might cause network interruption.

Non-default vSystems do not support this command.

A Blade aggregation group with a number in the range of 1 to 255 cannot forward traffic correctly if the corresponding security engine group contains multiple types of security engines. To ensure correct traffic forwarding, you must specify a Blade type for the Blade aggregate interface.

Examples

# Specify the Blade type as blade4fw for Blade-Aggregation 1.

<Sysname> system-view

[Sysname] interface blade-aggregation 1

[Sysname-Blade-Aggregation1] link-aggregation blade blade4fw

link-aggregation global load-sharing mode

Use link-aggregation global load-sharing mode to set the global link-aggregation load sharing mode.

Use undo link-aggregation global load-sharing mode to restore the default.

Syntax

link-aggregation global load-sharing mode { destination-ip | source-ip } *

undo link-aggregation global load-sharing mode

Default

Link aggregation groups distribute traffic based on source and destination IP addresses.

Views

System view

Predefined user roles

network-admin

context-admin

Parameters

destination-ip: Distributes traffic based on destination IP addresses.

source-ip: Distributes traffic based on source IP addresses.

Usage guidelines

Non-default vSystems do not support this command.

If you execute this command multiple times, the most recent configuration takes effect.

If an unsupported load sharing mode is set, the device displays an error message.

Examples

# Set the global load sharing mode to load share packets based on destination MAC addresses.

<Sysname> system-view

[Sysname] link-aggregation global load-sharing mode destination-mac

Related commands

bandwidth

link-aggregation load-sharing mode

link-aggregation ignore vlan

Use link-aggregation ignore vlan to configure a Layer 2 aggregate interface to ignore the specified VLANs.

Use undo link-aggregation ignore vlan to remove the specified ignored VLANs for a Layer 2 aggregate interface.

Syntax

link-aggregation ignore vlan vlan-id-list

undo link-aggregation ignore vlan vlan-id-list

Default

A Layer 2 aggregate interface does not ignore any VLANs.

Views

Layer 2 aggregate interface view

Predefined user roles

network-admin

context-admin

Parameters

vlan-id-list: Specifies a space-separated list of up to 10 VLAN items. Each item specifies a VLAN ID or a range of VLAN IDs in the form of vlan-id1 to vlan-id2. The value range for VLAN IDs is 1 to 4094. The value for the vlan-id2 argument must be equal to or greater than the value for the vlan-id1 argument.

Usage guidelines

Non-default vSystems do not support this command.

This command takes effect only when the link type of the Layer 2 aggregate interface is hybrid or trunk.

With this command configured, a Layer 2 aggregate interface ignores the permitted VLAN and VLAN tagging mode configuration of the specified VLANs when choosing Selected ports.

Examples

# Configure Layer 2 aggregate interface bridge-aggregation 1 to ignore VLAN 50.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation ignore vlan 50

link-aggregation lacp isolate

Use link-aggregation lacp isolate to isolate aggregate interfaces on the device.

Use undo link-aggregation lacp isolate to remove aggregate interface isolation.

Syntax

link-aggregation lacp isolate

undo link-aggregation lacp isolate

Default

Aggregate interfaces are not isolated.

Views

System view

Predefined user roles

network-admin

context-admin

Usage guidelines

Aggregate interface isolation gracefully changes member ports of all dynamic aggregate interfaces to Unselected state. The member ports of the counterpart aggregation groups will also be placed in Unselected state.

This feature takes effect only on dynamic aggregate interfaces. It cannot isolate static aggregate interfaces.

Examples

# Isolate aggregate interfaces.

<Sysname> system-view

[Sysname] link-aggregation lacp isolate

link-aggregation lacp traffic-redirect-notification enable

Use link-aggregation lacp traffic-redirect-notification enable to enable link-aggregation traffic redirection.

Use undo link-aggregation lacp traffic-redirect-notification enable to disable link-aggregation traffic redirection.

Syntax

link-aggregation lacp traffic-redirect-notification enable

undo link-aggregation lacp traffic-redirect-notification enable

Default

Link-aggregation traffic redirection is disabled.

Views

System view

Predefined user roles

network-admin

context-admin

Usage guidelines

Non-default vSystems do not support this command.

This feature redirects traffic on a Selected port to the remaining available Selected ports of an aggregation group if the port is shut down by using the shutdown command or the slot that hosts the port reboots.

NOTE:

The device does not redirect traffic to member ports that become Selected during the traffic redirection process.

This feature ensures zero packet loss for known unicast traffic, but does not protect unknown unicast traffic.

This feature applies only to dynamic link aggregation groups.

To prevent traffic interruption, enable link-aggregation traffic redirection on devices at both ends of the aggregate link.

To prevent packet loss that might occur when a slot reboots, do not enable spanning tree together with link-aggregation traffic redirection.

Link-aggregation traffic redirection cannot operate correctly on an edge aggregate interface.

Examples

# Enable link-aggregation traffic redirection.

<Sysname> system-view

[Sysname] link-aggregation lacp traffic-redirect-notification enable

link-aggregation load-sharing mode

Use link-aggregation load-sharing mode to set the link-aggregation load sharing mode for an aggregation group.

Use undo link-aggregation load-sharing mode to restore the default.

Syntax

link-aggregation load-sharing mode { { destination-ip | destination-mac | destination-port | ip-protocol | mpls-label1 | source-ip | source-mac | source-port | per-packet }

undo link-aggregation load-sharing mode

Default

An aggregation group uses the global link-aggregation load sharing mode.

Views

Blade aggregate interface view

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

context-admin

Parameters

destination-ip: Distributes traffic based on destination IP addresses.

destination-mac: Distributes traffic based on destination MAC addresses.

destination-port: Distributes traffic based on destination ports.

ip-protocol: Distributes traffic based on IP protocol types.

mpls-label1: Distributes MPLS traffic based on Layer 1 labels.

source-ip: Distributes traffic based on source IP addresses.

source-mac: Distributes traffic based on source MAC addresses.

source-port: Distributes traffic based on source ports.

per-packet: Distributes traffic on a per-packet basis. Traffic is distributed across the Selected member ports in proportion to their expected bandwidth, which is configurable with the bandwidth command.

Usage guidelines

Non-default vSystems do not support this command.

If you execute this command multiple times, the most recent configuration takes effect.

If an unsupported load sharing mode is set, the device displays an error message.

Blade aggregate interfaces distribute packets based on only source and destination IP addresses.

Examples

# Configure Layer 2 aggregation group 1 to load share packets based on destination MAC addresses.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation load-sharing mode destination-mac

# Configure Layer 3 aggregation group 1 to load share packets based on destination MAC addresses.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] link-aggregation load-sharing mode destination-mac

Related commands

bandwidth

link-aggregation global load-sharing mode

link-aggregation load-sharing mode local-first

Use link-aggregation load-sharing mode local-first to enable local-first load sharing for link aggregation globally.

Use undo link-aggregation load-sharing mode local-first to disable local-first load sharing for link aggregation globally.

Syntax

link-aggregation load-sharing mode local-first

undo link-aggregation load-sharing mode local-first

The following compatibility matrix shows the support of hardware platforms for this command:

Hardware platform	Module type	Command compatibility
M9006 M9010 M9014	Blade IV firewall module	Yes
	Blade V firewall module	Yes
	NAT module	No
M9010-GM	Encryption module	No
M9016-V	Blade V firewall module	Yes
M9008-S M9012-S	Blade IV firewall module	Yes
	Intrusion prevention service (IPS) module	Yes
	Video network gateway module	Yes
M9008-S-V	Blade IV firewall module	Yes
M9000-AI-E4 M9000-AI-E8 M9000-AI-E16	Blade V firewall module	Yes
M9000-X06 M9000-X10	Blade VI firewall module	No
M9000-AI-X06 M9000-AI-X10	Blade VI firewall module	No

‌

Default

Local-first load sharing is enabled for link aggregation globally.

Views

System view

Predefined user roles

network-admin

context-admin

Usage guidelines

Non-default vSystems do not support this command.

Use local-first load sharing in a multichassis link aggregation scenario to distribute traffic preferentially across member ports on the ingress device.

If you disable local-first load sharing, packets of an aggregate interface are load shared among all Selected ports on IRF member devices.

You can configure local-first load sharing globally or on a per-interface basis. An aggregate interface preferentially uses the interface-specific setting. If no interface-specific setting is available, the aggregate interface uses the global setting.

Examples

# Disable local-first load sharing for link aggregation globally.

<Sysname> system-view

[Sysname] undo link-aggregation load-sharing mode local-first

Related commands

link-aggregation group load-sharing mode local-first

link-aggregation mode

Use link-aggregation mode dynamic to configure an aggregation group to operate in dynamic aggregation mode and enable LACP.

Use undo link-aggregation mode to restore the default.

Syntax

link-aggregation mode dynamic

undo link-aggregation mode

Default

An aggregation group operates in static aggregation mode.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

context-admin

Usage guidelines

Non-default vSystems do not support this command.

Aggregation mode change might cause Selected member ports to become Unselected.

When you change the aggregation mode, make sure you understand the impact of the change on services.

Examples

# Configure Layer 2 aggregation group 1 to operate in dynamic aggregation mode.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation mode dynamic

# Configure Layer 3 aggregation group 1 to operate in dynamic aggregation mode.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] link-aggregation mode dynamic

link-aggregation rbm-related

Use link-aggregation rbm-related to enable RBM collaboration for an aggregate interface.

Use undo link-aggregation rbm-related to disable RBM collaboration for an aggregate interface.

Syntax

link-aggregation rbm-related

undo link-aggregation rbm-related

Default

RBM collaboration is disabled for an aggregate interface.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

context-admin

Usage guidelines

Application scenarios

In an RBM active/standby hot backup system, the member interfaces of an aggregate interface on the primary device are configured as Selected ports, while the member interfaces of the aggregate interface with the same number on the secondary device are configured as Unselected ports. This ensures that traffic on the aggregate interface is processed by the primary device.

Restrictions and guidelines

When you enable RBM collaboration for an aggregate interface, even if the aggregate interface has no Selected ports, the aggregate interface will maintain the up state.

Examples

# Enable RBM collaboration for an aggregate interface.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation rbm-related

link-aggregation port-priority

Use link-aggregation port-priority to set the port priority of an interface.

Use undo link-aggregation port-priority to restore the default.

Syntax

link-aggregation port-priority priority

undo link-aggregation port-priority

Default

The port priority of an interface is 32768.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

context-admin

Parameters

priority: Specifies the port priority in the range of 0 to 65535. The smaller the value, the higher the port priority.

Usage guidelines

Non-default vSystems do not support this command.

Examples

# Set the port priority to 64 for Layer 2 Ethernet interface GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] link-aggregation port-priority 64

# Set the port priority to 64 for Layer 3 Ethernet interface GigabitEthernet 1/0/2.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/2

[Sysname-GigabitEthernet1/0/2] link-aggregation port-priority 64

Related commands

lacp system-priority

link-aggregation selected-port maximum

Use link-aggregation selected-port maximum to set the maximum number of Selected ports allowed in an aggregation group.

Use undo link-aggregation selected-port maximum to restore the default.

Syntax

link-aggregation selected-port maximum max-number

undo link-aggregation selected-port maximum

Default

The maximum number of Selected ports allowed in an aggregation group depends on hardware limitation.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

context-admin

Parameters

max-number: Specifies the maximum number of Selected ports allowed in an aggregation group. The value range for this argument is 1 to 32.

Usage guidelines

Non-default vSystems do not support this command.

Executing this command might cause some of the Selected ports in an aggregation group to become Unselected ports.

The maximum number of Selected ports allowed in the aggregation groups must be the same for the local and peer ends.

For an aggregation group, the maximum number of Selected ports must be equal to or higher than the minimum number of Selected ports.

The maximum number of Selected ports allowed in an aggregation group is limited by one of the following values, whichever value is smaller:

· Maximum number set by using the link-aggregation selected-port maximum command.

· Maximum number of Selected ports allowed by the link aggregation capability.

You can implement backup between two ports by performing the following tasks:

· Assigning two ports to an aggregation group.

· Setting the maximum number of Selected ports to 1 for the aggregation group.

Then, only one Selected port is allowed in the aggregation group at any point in time, while the Unselected port acts as a backup port.

Examples

# Set the maximum number of Selected ports to 5 for Layer 2 aggregation group 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation selected-port maximum 5

# Set the maximum number of Selected ports to 5 for Layer 3 aggregation group 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] link-aggregation selected-port maximum 5

Related commands

link-aggregation selected-port minimum

Use link-aggregation selected-port minimum to set the minimum number of Selected ports in an aggregation group.

Use undo link-aggregation selected-port minimum to restore the default.

Syntax

link-aggregation selected-port minimum min-number

undo link-aggregation selected-port minimum

Default

The minimum number of Selected ports in an aggregation group is not specified.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

context-admin

Parameters

min-number: Specifies the minimum number of Selected ports in an aggregation group required to bring up the aggregate interface. The value range for this argument is 1 to 32.

Usage guidelines

Non-default vSystems do not support this command.

Executing this command might cause all member ports in the aggregation group to become Unselected ports.

The minimum number of Selected ports allowed in the aggregation groups must be the same for the local and peer ends.

For an aggregation group, the minimum number of Selected ports must be equal to or lower than the maximum number of Selected ports.

Examples

# Set the minimum number of Selected ports to 3 for Layer 2 aggregation group 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation selected-port minimum 3

# Set the minimum number of Selected ports to 3 for Layer 3 aggregation group 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] link-aggregation selected-port minimum 3

Related commands

link-aggregation selected-port maximum

link-delay

Use link-delay to set the physical state change suppression interval on an aggregate interface.

Use undo link-delay to restore the default.

Syntax

link-delay [ msec ] delay-time [ mode { up | updown } ]

undo link-delay [ msec ] delay-time [ mode { up | updown } ]

Default

Each time the physical link of an aggregate interface goes up or comes down, the system immediately reports the change to the CPU.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

context-admin

Parameters

msec: Sets the physical state change suppression interval in milliseconds. If you do not specify this keyword, the suppression interval is in seconds.

delay-time: Sets the physical state change suppression interval. To report a physical state change immediately to the CPU, set the interval to 0.

· If you do not specify the msec keyword, the value range is 0 to 30 seconds.

· If you specify the msec keyword, the value range is 0 to 10000 milliseconds, and the value must be a multiple of 100.

mode up: Suppresses link-up events.

mode updown: Suppresses both link-up and link-down events.

Usage guidelines

Non-default vSystems do not support this command.

You can configure this feature to suppress only link-down events, only link-up events, or both. If an event of the specified type persists when the suppression interval expires, the system reports the event.

When you configure this feature, follow these guidelines:

· To suppress only link-down events, use the link-delay [ msec ] delay-time command.

· To suppress only link-up events, use the link-delay [ msec ] delay-time mode up command.

· To suppress both link-down and link-up events, use the link-delay [ msec ] delay-time mode updown command.

On an interface, you can configure different suppression intervals for link-up and link-down events. If you execute the link-delay command multiple times for link-up or link-down events, the most recent configuration takes effect.

Examples

# Set the link-down event suppression interval to 8 seconds on Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-delay down 8

# Set the link-down event suppression interval to 8 seconds on Route-Aggregation 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] link-delay down 8

mac-address

Use mac-address to assign a MAC address to an aggregate interface.

Use undo mac-address to restore the default.

Syntax

mac-address mac-address

undo mac-address

Default

All aggregate interfaces on the device use the same default MAC address.

Views

Layer 3 aggregate interface view

Predefined user roles

network-admin

context-admin

Parameters

mac-address: Specifies a MAC address in the format of H-H-H.

Usage guidelines

Non-default vSystems do not support this command.

The default MAC address of Layer 3 aggregate interfaces and subinterfaces varies by device. You can use the display interface command to view the MAC address of a Layer 3 aggregate interface or subinterface.

Examples

# Assign MAC address 0001-0001-0002 to interface Route-Aggregation 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] mac-address 1-1-2

mtu

Use mtu to set the MTU of a Layer 3 aggregate interface or subinterface.

Use undo mtu to restore the default.

Syntax

mtu size

undo mtu

Default

The MTU of Layer 3 aggregate interfaces and subinterfaces is 1500 bytes.

Views

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

Predefined user roles

network-admin

context-admin

Parameters

size: Specifies an MTU in bytes. The value range for this argument is 46 to 9198..

Usage guidelines

Non-default vSystems do not support this command.

Examples

# Set the MTU of interface Route-Aggregation 1 to 1430 bytes.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] mtu 1430

Related commands

display interface

port link-aggregation group

Use port link-aggregation group to assign an interface to an aggregation group.

Use undo port link-aggregation group to remove an interface from the aggregation group to which it belongs.

Syntax

port link-aggregation group group-id

undo port link-aggregation group

Default

An interface does not belong to any aggregation group.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

context-admin

Parameters

group-id: Specifies an aggregation group by its aggregate interface number. The value range for the number argument is 1 to 1024.

Usage guidelines

Non-default vSystems do not support this command.

An interface can belong to only one aggregation group.

The following restrictions apply if you have not enabled multi-VLAN termination on an aggregate interface by using the link-aggregation multivlan-termination command:

· You cannot assign both Ethernet interfaces and Ethernet subinterfaces to the aggregation group.

· You cannot create subinterfaces on an Ethernet interface that is in the aggregation group.

· You cannot assign an Ethernet interface that has subinterfaces to the aggregation group.

You cannot create aggregate subinterfaces on an aggregate interface if its aggregation group contains Ethernet subinterfaces. You cannot assign Ethernet subinterfaces to an aggregation group if its aggregate interface has aggregate subinterfaces.

Before you assign an Ethernet subinterface to an aggregation group, perform the following tasks:

· If multi-VLAN termination is not enabled on the aggregate interface, configure VLAN termination on the Ethernet subinterface. You will be unable to modify the VLAN termination configuration after you assign the subinterface to the aggregation group. To configure VLAN termination, use the following commands:

¡ vlan-type dot1q default.

¡ vlan-type dot1q untagged.

¡ vlan-type dot1q vid.

¡ vlan-type dot1q vid second-dot1q.

· To assign Ethernet subinterfaces that terminate different VLANs to the same aggregation group, enable multi-VLAN termination on the aggregate interface. If multi-VLAN termination is not enabled on the aggregate interface, you must make sure the Ethernet subinterfaces to be assigned to its aggregation group terminate the same VLAN.

· If you are assigning the Ethernet subinterface to a dynamic aggregation group, specify only one VLAN ID when you execute the vlan-type dot1q vid vlan-id-list [ loose ] command.

You cannot assign the following interfaces to an aggregation group:

· Member interfaces of redundant Ethernet interfaces.

· Member interfaces of redundancy group nodes.

For more information about redundant Ethernet interfaces and redundancy group nodes, see Virtual Technologies Configuration Guide.

Examples

# Assign Layer 2 Ethernet interface GigabitEthernet 1/0/1 to Layer 2 aggregation group 1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port link-aggregation group 1

# Assign Layer 3 Ethernet interface GigabitEthernet 1/0/2 to Layer 3 aggregation group 2.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/2

[Sysname-GigabitEthernet1/0/2] port link-aggregation group 2

Related commands

link-aggregation multivlan-termination

vlan-type dot1q default

vlan-type dot1q untagged

vlan-type dot1q vid

reset counters interface

Use reset counters interface to clear statistics about the specified aggregate interfaces.

Syntax

reset counters interface [ { blade-aggregation | bridge-aggregation | route-aggregation | schannel-bundle } [ interface-number ] ]

Views

User view

Predefined user roles

network-admin

context-admin

vsys-admin

Parameters

blade-aggregation: Specifies Blade aggregate interfaces.

bridge-aggregation: Specifies Layer 2 aggregate interfaces.

route-aggregation: Specifies Layer 3 aggregate interfaces.

interface-number: Specifies an existing aggregate interface number.

Usage guidelines

Use this command to clear history statistics before you collect traffic statistics for a time period.

If you do not specify an aggregate interface type, the command clears statistics about all interfaces in the system except VA interfaces.

If you specify only an aggregate interface type, the command clears statistics about all aggregate interfaces of the specified type.

The blade-aggregation, bridge-aggregation, or route-aggregation keyword is available only when aggregate interfaces of the corresponding type exist on the device.

Examples

# Clear the statistics about interface Bridge-Aggregation 1.

<Sysname> reset counters interface bridge-aggregation 1

reset lacp statistics

Use reset lacp statistics to clear LACP statistics about the specified link aggregation member ports.

Syntax

reset lacp statistics [ interface interface-list ]

Views

User view

Predefined user roles

network-admin

context-admin

Parameters

interface interface-list: Specifies a list of link aggregation member ports, in the format interface-type interface-number1 [ to interface-type interface-number2 ]. The value for the interface-number1 argument must be equal to or greater than the value for the interface-number2 argument. If you do not specify any member ports, the command clears LACP statistics about all member ports.

Usage guidelines

Non-default vSystems do not support this command.

Examples

# Clear LACP statistics about all link aggregation member ports.

<Sysname> reset lacp statistics

Related commands

display link-aggregation member-port

shutdown

Use shutdown to shut down an aggregate interface or subinterface.

Use undo shutdown to bring up an aggregate interface or subinterface.

Syntax

shutdown

undo shutdown

Default

An interface is not manually shut down.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

Predefined user roles

network-admin

context-admin

Usage guidelines

CAUTION:

The shutdown command will disconnect all links established on an interface. Make sure you are fully aware of the impacts of this command when you use it on a live network.

Non-default vSystems do not support this command.

Shutting down or bringing up a Layer 3 aggregate interface shuts down or brings up its subinterfaces. Shutting down or bringing up a Layer 3 aggregate subinterface does not affect its main interface.

Examples

# Bring up Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] undo shutdown

# Bring up Layer 3 aggregate interface Route-Aggregation 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] undo shutdown

sub-interface rate-statistic

Use sub-interface rate-statistic to enable rate statistics collection for the subinterfaces of a Layer 3 aggregate interface.

Use undo sub-interface rate-statistic to disable rate statistics collection for the subinterfaces of a Layer 3 aggregate interface.

Syntax

sub-interface rate-statistic

undo sub-interface rate-statistic

Default

Rate statistics collection is disabled for Layer 3 aggregate subinterfaces.

Views

Layer 3 aggregate interface view

Predefined user roles

network-admin

context-admin

Usage guidelines

Rate statistics collection for Layer 3 aggregate subinterfaces is resource intensive. When you use this feature on a live network, make sure you fully understand its impact.

This command enables the device to periodically refresh rate statistics for the subinterfaces of a Layer 3 aggregate interface. The rate statistics are available in two statistics polling intervals after you execute this command. To set the statistics polling interval, use the flow-interval command.

Examples

# Enable rate statistics collection for the subinterfaces of Route-Aggregation 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] sub-interface rate-statistic

This configuration may make a negative effect on the performance. Are you sure to continue? [Y/N]:y

The configuration will take effect after 2 flow intervals.

Related commands

flow-interval (Ethernet interface commands)

10-Layer 2—LAN Switching Command Reference

display link-aggregation verbose

interface blade-aggregation

interface route-aggregation

link-aggregation rbm-related

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

News & Events

Contact Us