Contents

QinQ commands· 1

display qinq· 1

qinq enable· 2

qinq ethernet-type (interface view) 2

qinq ethernet-type (system view) 3

qinq transparent-vlan· 5

 

QinQ commands

Do not configure QinQ and Ethernet service instance-to-VSI binding on the same Layer 2 Ethernet interface or Layer 2 aggregate interface. Do not configure QinQ on a Layer 2 Ethernet interface or Layer 2 aggregate interface that acts as the source interface of a VXLAN tunnel. Otherwise, these features might not take effect. For more information about VXLAN and VSI, see VXLAN Configuration Guide.

This document uses the following terms:

·     CVLAN—Customer network VLANs, also called inner VLANs, refer to VLANs that a customer uses on the private network.

·     SVLAN—Service provider network VLANs, also called outer VLANs, refer to VLANs that a service provider uses to transmit VLAN tagged traffic for customers.

display qinq

Use display qinq to display QinQ-enabled interfaces.

Syntax

display qinq [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays all QinQ-enabled interfaces.

Usage guidelines

If QinQ is not enabled on any interfaces, this command does not provide any output.

Examples

# Enable QinQ on Ten-GigabitEthernet 1/0/1. Then, verify that QinQ is enabled on the interface.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] qinq enable

[Sysname-Ten-GigabitEthernet1/0/1] display qinq interface ten-gigabitethernet 1/0/1

Interface

 Ten-GigabitEthernet1/0/1

# Enable QinQ on Ten-GigabitEthernet 1/0/1 and Ten-GigabitEthernet 1/0/3. Then, verify that QinQ is enabled on the interfaces.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] qinq enable

[Sysname-Ten-GigabitEthernet1/0/1] quit

[Sysname] interface ten-gigabitethernet 1/0/3

[Sysname-Ten-GigabitEthernet1/0/3] qinq enable

[Sysname-Ten-GigabitEthernet1/0/3] display qinq

Interface

 Ten-GigabitEthernet1/0/1

 Ten-GigabitEthernet1/0/3

Related commands

qinq enable

qinq enable

Use qinq enable to enable QinQ on an interface.

Use undo qinq enable to disable QinQ on an interface.

Syntax

qinq enable

undo qinq enable

Default

QinQ is disabled on interfaces.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Examples

# Enable QinQ on Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] qinq enable

Related commands

display qinq

qinq ethernet-type (interface view)

Use qinq ethernet-type to set the TPID value in SVLAN tags on an interface.

Use undo qinq ethernet-type to restore the default TPID value in SVLAN tags on an interface.

Syntax

qinq ethernet-type service-tag hex-value

undo qinq ethernet-type service-tag

Default

The TPID value in SVLAN tags is 8100 in hexadecimal notation.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

service-tag: Sets the TPID value in the SVLAN tag.

hex-value: Sets a hexadecimal TPID value in the range of 1 to ffff, excluding the reserved EtherType values listed in Table 1.

Table 1 Reserved EtherType values

Protocol type	Value
ARP	0x0806
PUP	0x0200
RARP	0x8035
IP	0x0800
IPv6	0x86dd
PPPoE	0x8863/0x8864
MPLS	0x8847/0x8848
IPX/SPX	0x8137
IS-IS	0x8000
LACP	0x8809
LLDP	0x88cc
802.1X	0x888e
802.1ag	0x8902
Cluster	0x88a7
Reserved	0xfffd/0xfffe/0xffff

 

Usage guidelines

A port without QinQ enabled uses the SVLAN TPID to match incoming tagged frames. The port modifies the TPID in the SVLAN tag of outgoing frames as the configured value.

Examples

# Set the TPID value in SVLAN tags to 9100 (hexadecimal) on Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] qinq ethernet-type service-tag 9100

Related commands

qinq ethernet-type (system view)

qinq ethernet-type (system view)

Use qinq ethernet-type to set the TPID value in CVLAN tags.

Use undo qinq ethernet-type to restore the default TPID value in CVLAN tags.

Syntax

qinq ethernet-type customer-tag hex-value

undo qinq ethernet-type customer-tag

Default

The TPID value in CVLAN tags is 8100 in hexadecimal notation.

Views

System view

Predefined user roles

network-admin

Parameters

customer-tag: Sets the TPID value in the CVLAN tag.

hex-value: Sets a hexadecimal TPID value in the range of 1 to ffff, excluding the reserved EtherType values listed in Table 2.

Table 2 Reserved EtherType values

Protocol type	Value
ARP	0x0806
PUP	0x0200
RARP	0x8035
IP	0x0800
IPv6	0x86dd
PPPoE	0x8863/0x8864
MPLS	0x8847/0x8848
IPX/SPX	0x8137
IS-IS	0x8000
LACP	0x8809
LLDP	0x88cc
802.1X	0x888e
802.1ag	0x8902
Cluster	0x88a7
Reserved	0xfffd/0xfffe/0xffff

 

Examples

# Set the TPID value in CVLAN tags to 8200 (hexadecimal).

<Sysname> system-view

[Sysname] qinq ethernet-type customer-tag 8200

Related commands

qinq ethernet-type (interface view)

qinq transparent-vlan

Use qinq transparent-vlan to enable transparent transmission for a list of VLANs on a port.

Use undo qinq transparent-vlan to disable transparent transmission for a list of VLANs on a port.

Syntax

qinq transparent-vlan vlan-id-list

undo qinq transparent-vlan { vlan-id-list | all }

Default

Transparent transmission is disabled for all VLANs.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

vlan-id-list: Specifies a space-separated list of up to 10 VLAN items. Each item specifies a single VLAN ID or a VLAN ID range in the form of vlan-id1 to vlan-id2. The value range for VLAN IDs is 1 to 4094. The end VLAN ID must be equal to or greater than the start VLAN ID.

all: Specifies all VLANs.

Usage guidelines

By default, QinQ tags all incoming frames with the PVID on a port. This command disables QinQ to tag incoming traffic from a list of VLANs. These VLANs are called transparent VLANs.

You can repeat this command to add VLANs to the list of transparent VLANs.

To ensure successful transmission for a transparent VLAN, follow these configuration guidelines:

·     Set the link type of the port to trunk or hybrid, and assign the port to the transparent VLAN.

·     Do not configure any other VLAN manipulation actions for the transparent VLAN on the port.

·     Make sure all ports on the traffic path permit the transparent VLAN to pass through.

·     If you use both transparent VLANs and VLAN mappings on an interface, the transparent VLANs cannot be the following VLANs:

¡     Original or translated VLANs of one-to-one or one-to-two VLAN mappings.

¡     Original or translated outer VLANs of two-to-two VLAN mappings.

Examples

# Configure Ten-GigabitEthernet 1/0/1 as a trunk port, and assign the port to VLAN 2, VLAN 3, and VLANs 50 through 100. Enable QinQ on Ten-GigabitEthernet 1/0/1, and configure the port to transparently transmit frames from VLAN 2.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] port link-type trunk

[Sysname-Ten-GigabitEthernet1/0/1] port trunk permit vlan 2 3 50 to 100

[Sysname-Ten-GigabitEthernet1/0/1] qinq enable

[Sysname-Ten-GigabitEthernet1/0/1] qinq transparent-vlan 2