priority { critical | high | low | medium }: Specifies a route convergence priority. To display route information with the critical priority, specify the critical keyword. To display route information with the high priority, specify the high keyword. To display route information with the low priority, specify the low keyword. To display route information with the medium priority, specify the medium keyword. If you do not specify any of the keywords, this command displays route information with all priorities.

all-routes: Displays routing table information for the public network and all VPN instances.

verbose: Displays detailed routing table information, including information about both active and inactive routes. If you do not specify this keyword, the command displays only brief information about active routes.

fast-reroute: Displays fast reroute routing table information.

Usage guidelines

If you do not specify any parameters, this command displays routing table information for the public network, excluding fast reroute routing table information.

Examples

# Display brief information about active routes in the public network.

<Sysname> display ip routing-table

Destinations : 8 Routes : 8

Destination/Mask Proto Pre Cost NextHop Interface

0.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0

1.1.1.0/24 Static 60 0 192.168.47.4 XGE3/0/1

127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0

127.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0

127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0

127.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0

192.168.1.40/32 Direct 0 0 127.0.0.1 InLoop0

255.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0

# Display brief information about active routes in the routing table for the public network and all VPN instances.

<Sysname> display ip routing-table all-routes

VPN instance: public instance

Destinations : 8 Routes : 8

Destination/Mask Proto Pre Cost NextHop Interface

0.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0

1.1.1.0/24 Static 60 0 192.168.47.4 XGE3/0/1

127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0

127.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0

127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0

127.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0

192.168.1.40/32 Direct 0 0 127.0.0.1 InLoop0

255.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0

VPN instance: vpn1

Destinations : 5 Routes : 5

Destination/Mask Proto Pre Cost NextHop Interface

0.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0

1.1.2.0/24 Static 60 0 2.2.1.1 XGE3/0/1

3.3.1.0/24 BGP 255 0 55.1.1.2 XGE3/0/2

127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0

255.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0

# Display IPv4 routing table information for all VPN instances.

<Sysname> display ip routing-table all-vpn-instance

VPN instance: vpn1

Destinations : 5 Routes : 5

Destination/Mask Proto Pre Cost NextHop Interface

0.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0

1.1.2.0/24 Static 60 0 2.2.1.1 XGE3/0/1

3.3.1.0/24 BGP 255 0 55.1.1.2 XGE3/0/2

127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0

255.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0

VPN instance: vpn2

Destinations : 4 Routes : 4

Destination/Mask Proto Pre Cost NextHop Interface

0.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0

1.1.3.0/24 Static 60 0 3.3.1.1 XGE3/0/1

127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0

255.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0

Table 1 Command output

Field	Description
VPN instance	Public network or VPN instance to which the routing table belongs. For the public network, this filed displays public instance. For a VPN instance, this field displays the name of the instance.
Destinations	Number of destination addresses.
Routes	Number of routes.
Destination/Mask	Destination address/mask length.
Proto	Route type or protocol that installed the route: · Direct—Direct route. · Static—Static route. · UNR—User network route. · RIP—RIP installed the route. · O_INTRA—OSPF intra-area route. · O_ASE2—OSPF Type-2 external route. · IS_L1—Level-1 IS-IS IPv4 route. · IS_L2—Level-2 IS-IS IPv4 route. · BGP—BGP installed the route. · EIGRP—EIGRP installed the route. · LISP—LISP installed the route.
Pre	Preference of the route.
Cost	Cost of the route.
NextHop	Next hop address of the route.
Interface	Output interface for packets to be forwarded along the route.
Summary count	Number of routes.

# Display detailed information about all routes in the public network.

<Sysname> display ip routing-table verbose

Destinations : 4 Routes : 4

Destination: 0.0.0.0/32

Protocol: Direct

Process ID: 0

SubProtID: 0x0 Age: 08h34m37s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NibID: 0x10000000 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x1000c OrigNextHop: 127.0.0.1

Label: NULL RealNextHop: 127.0.0.1

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: InLoopBack0

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: InLoopBack0

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

Destination: 1.1.1.0/24

Protocol: Static

Process ID: 0

SubProtID: 0x0 Age: 04h20m37s

FlushedAge: 15h28m49s

Cost: 0 Preference: 60

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NibID: 0x10000003 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x1008c OrigNextHop: 192.168.47.4

Label: NULL RealNextHop: 192.168.47.4

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: Ten-GigabitEthernet3/0/1

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: Ten-GigabitEthernet3/0/1

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

Destination: 1.1.1.0/24

Protocol: Static

Process ID: 0

SubProtID: 0x0 Age: 04h20m37s

FlushedAge: 15h28m49s

Cost: 0 Preference: 60

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active Adv Derived

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NibID: 0x10000003 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x1008c OrigNextHop: 192.168.47.4

Label: NULL RealNextHop: 125.2.1.1

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: Ten-GigabitEthernet3/0/2

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: Ten-GigabitEthernet3/0/2

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

...

# Display detailed routing table information for all VPN instances.

<Sysname> display ip routing-table all-vpn-instance verbose

VPN instance: vpn1

Destinations : 1 Routes : 1

Destination: 0.0.0.0/32

Protocol: Direct

Process ID: 0

SubProtID: 0x0 Age: 08h34m37s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: vpn1

TableID: 0x2 OrigAs: 0

NibID: 0x10000000 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x1000c OrigNextHop: 127.0.0.1

Label: NULL RealNextHop: 127.0.0.1

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: InLoopBack0

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: InLoopBack0

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

VPN instance: vpn2

Destinations : 1 Routes : 1

Destination: 1.1.1.0/24

Protocol: Static

Process ID: 0

SubProtID: 0x0 Age: 04h20m37s

FlushedAge: 15h28m49s

Cost: 0 Preference: 60

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: vpn2

TableID: 0x2 OrigAs: 0

NibID: 0x10000003 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x1008c OrigNextHop: 192.168.47.4

Label: NULL RealNextHop: 192.168.47.4

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: Ten-GigabitEthernet3/0/1

BkSRLabel: NULL BkInterface: N/A

SIDIndex: NULL InLabel: NULL

Tunnel ID: Invalid IPInterface: Ten-GigabitEthernet3/0/1

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

...

Table 2 Command output

Field	Description
VPN instance	Public network or VPN instance to which the routing table belongs. For the public network, this filed displays public instance. For a VPN instance, this field displays the name of the instance.
Destinations	Number of destination addresses.
Routes	Number of routes.
Destination	Destination address/mask length.
Protocol	Protocol that installed the route.
SubProtID	ID of the subprotocol for routing.
Age	Time for which the route has been in the routing table.
FlushedAge	Time for which the route has been flushed to the FIB.
Cost	Cost of the route.
Preference	Preference of the route.
IpPre	IP precedence.
QosLocalID	Local QoS ID.
Tag	Route tag.
State	Route status: · Active—Active unicast route. · Adv—Route that can be advertised. · Inactive—Inactive route. · NoAdv—Route that the router is not allowed to advertise. · Vrrp—Routes generated by VRRP. · Nat—Routes generated by NAT. · TunE—Tunnel. · Derived—Derived route. If a route recurses to multiple related routes, all related routes except the first one are derived routes. The number of derived routes is not included in the total number of routes. · Backup—Backup route.
OrigTblID	Original routing table ID.
OrigVrf	Original VPN instance to which the route belongs. This field displays default-vrf if the route is on the public network.
TableID	ID of the routing table.
OrigAs	Original AS number.
NibID	ID of the next hop.
LastAs	Last AS number.
AttrID	Attribute ID.
BkAttrID	Attribute ID of the backup route. This field displays only the attribute ID of the backup route added by BGP to the IP routing table.
Neighbor	Address of the neighbor determined by the routing protocol.
Flags	Flags of the route.
OrigNextHop	Next hop address of the route.
RealNextHop	Real next hop of the route.
BkLabel	Backup label.
BkNexthop	Backup next hop.
SRLabel	Segment routing (SR) label.
Interface	Output interface for packets to be forwarded along the route.
BkSRLabel	Backup SR label.
BkInterface	Backup output interface.
Tunnel ID	Tunnel ID
IPInterface	IP output interface.
BkTunnel ID	Backup tunnel ID.
BkIPInterface	Backup IP output interface.
InLabel	Incoming label of the route.
ColorInterface	Output interface recursed by an SR-MPLS TE policy or SRv6 TE policy.
SIDIndex	SID index value.
BkColorInterface	Backup output interface recursed by an SR-MPLS TE policy or SRv6 TE policy.
FtnIndex	Index of the FTN entry.
TunnelInterface	Output tunnel interface.
TrafficIndex	Traffic index in the range of 1 to 64. This field displays N/A when the value is invalid.
BkTunnelInterface	Backup output tunnel interface.
Connector	BGP connector attribute exchanged between BGP peers along with a VPN IPv4 route. The value of the attribute is the IP address of the remote PE device. The BGP connector attribute is used for MD VPN. This field displays N/A if the BGP connector attribute is not supported.
Summary count	Number of routes.
PathID	Path ID.
UserID	Access user ID.
SRTunnelID	SR tunnel ID.
SID Type	This field is not supported in the current software version. SID type. If the route does not have an SID, this field displays N/A.
NID	Index of the Next Hop Label Forwarding Entry (Next Hop Label Forwarding Entry) flushed by the routing protocol.
FlushNID	Index of the NHLFE flushed to the FIB.
BkNID	Index of the backup NHLFE flushed by the routing protocol.
BkFlushNID	Index of the backup NHLFE flushed to the FIB.
StatFlags	Flags for SRv6 traffic statistics.
SID	Primary Segment Identifier (SID). If no primary SID is available, this field displays N/A.
BkSID	Backup SID. If no backup SID is available, this field displays N/A.
CommBlockLen	Common prefix length in the locator.
Priority	Convergence priority of the route: · Critical. · High. · Medium. · Low.
MemberPort	Number of a member port in an aggregation group. If this attribute is not available, this field displays N/A.

‌

display ip routing-table acl

Use display ip routing-table acl to display information about routes permitted by a basic ACL.

Syntax

display ip routing-table [ vpn-instance vpn-instance-name ] acl ipv4-acl-number [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, the command displays routing information for the public network.

ipv4-acl-number: Specifies a basic ACL by its number in the range of 2000 to 2999.

verbose: Displays detailed information about all routes permitted by the basic ACL. If you do not specify this keyword, the command displays only brief information about active routes permitted by the basic ACL.

Usage guidelines

When you specify an ACL, follow these restrictions and guidelines:

· If the specified ACL does not exist or does not have any rules, the command displays information about all routes.

· If you specify the vpn-instance keyword for an ACL rule, the ACL rule will not take effect.

Examples

# Define basic ACL 2000 and set the route filtering rules.

<Sysname> system-view

[Sysname] acl basic 2000

[Sysname-acl-ipv4-basic-2000] rule permit source 192.168.1.0 0.0.0.255

[Sysname-acl-ipv4-basic-2000] rule deny source any

# Display brief information about active routes permitted by basic ACL 2000.

[Sysname-acl-ipv4-basic-2000] display ip routing-table acl 2000

Summary count : 4

Destination/Mask Proto Pre Cost NextHop Interface

192.168.1.0/24 Direct 0 0 192.168.1.111 XGE3/0/1

192.168.1.0/32 Direct 0 0 192.168.1.111 XGE3/0/1

192.168.1.111/32 Direct 0 0 127.0.0.1 InLoop0

192.168.1.255/32 Direct 0 0 192.168.1.111 XGE3/0/1

For descriptions about the command output, see Table 1.

# Display detailed information about all routes permitted by basic ACL 2000.

<Sysname> display ip routing-table acl 2000 verbose

Summary count : 4

Destination: 192.168.1.0/24

Protocol: Direct

Process ID: 0

SubProtID: 0x1 Age: 04h20m37s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NibID: 0x10000003 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x10080 OrigNextHop: 192.168.1.111

Label: NULL RealNextHop: 192.168.1.111

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: Ten-GigabitEthernet3/0/1

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: Ten-GigabitEthernet3/0/1

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

Destination: 192.168.1.0/32

Protocol: Direct

Process ID: 0

SubProtID: 0x0 Age: 04h20m37s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NibID: 0x10000003 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x1008c OrigNextHop: 192.168.1.111

Label: NULL RealNextHop: 192.168.1.111

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: Ten-GigabitEthernet3/0/1

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: Ten-GigabitEthernet3/0/1

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

Destination: 192.168.1.111/32

Protocol: Direct

Process ID: 0

SubProtID: 0x1 Age: 04h20m37s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NibID: 0x10000000 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x10004 OrigNextHop: 127.0.0.1

Label: NULL RealNextHop: 127.0.0.1

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: InLoopBack0

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: InLoopBack0

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

Destination: 192.168.1.255/32

Protocol: Direct

Process ID: 0

SubProtID: 0x0 Age: 04h20m37s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NibID: 0x10000003 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x1008c OrigNextHop: 192.168.1.111

Label: NULL RealNextHop: 192.168.1.111

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: Ten-GigabitEthernet3/0/1

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: Ten-GigabitEthernet3/0/1

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

For descriptions about the command output, see Table 2.

display ip routing-table ip-address

Use display ip routing-table ip-address to display information about routes to a specific destination address.

Use display ip routing-table ip-address1 to ip-address2 to display information about routes to a range of destination addresses.

Syntax

display ip routing-table [ vpn-instance vpn-instance-name ] ip-address [ mask-length | mask ] [ longer-match ] [ verbose ]

display ip routing-table [ vpn-instance vpn-instance-name ] ip-address1 to ip-address2 [ verbose ]

display ip routing-table [ vpn-instance vpn-instance-name ] fast-reroute ip-address [ mask-length | mask ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ip-address: Specifies a destination IP address in dotted decimal notation.

mask-length: Specifies the mask length, an integer in the range of 0 to 32.

mask: Specifies the IP address mask in dotted decimal notation.

longer-match: Displays the route entries that meet the matching rules as described in the usage guidelines.

ip-address1 to ip-address2: Specifies a destination IP address range.

verbose: Displays detailed routing table information, including information about both active and inactive routes. If you do not specify this keyword, the command displays brief information about active routes.

fast-reroute: Displays fast reroute routing table information.

Usage guidelines

Executing the command with different parameters yields different outputs.

· display ip routing-table ip-address

¡ The system ANDs the entered destination IP address with the subnet mask in each active route entry.

¡ The system ANDs the destination IP address in each active route entry with its own subnet mask.

If the two operations yield the same result for an entry, the entry is displayed.

· display ip routing-table ip-address mask

¡ The system ANDs the entered destination IP address with the entered subnet mask.

¡ The system ANDs the destination IP address in each active route entry with the entered subnet mask.

If the two operations yield the same result for an entry with a subnet mask not greater than the entered subnet mask, the entry is displayed.

· display ip routing-table ip-address longer-match

¡ The system ANDs the entered destination IP address with the subnet mask in the following way:

- If the entered IP address belongs to class A, B, or C, the system ANDs it with the default subnet mask of the corresponding class.

- If the entered IP address is 0.0.0.0, the system ANDs it with the subnet mask 0.0.0.0.

- Except the previous cases, for example, if the entered IP address is a multicast address or loopback address, the system ANDs it with the subnet mask 255.255.255.255.

¡ The system ANDs the destination IP address in each active route entry with the subnet mask of the entered IP address.

If the two operations yield the same result for multiple entries, all the entries are displayed.

· display ip routing-table ip-address mask longer-match

¡ The system ANDs the entered destination IP address with the entered subnet mask.

¡ The system ANDs the destination IP address in each active route entry with the entered subnet mask.

If the two operations yield the same result for multiple entries, all the entries are displayed.

· display ip routing-table ip-address1 to ip-address2

The system displays active route entries with destinations in the range of ip-address1/32 to ip-address2/32.

Examples

# Display brief information about the routes to the destination IP address 11.0.0.1.

<Sysname> display ip routing-table 11.0.0.1

Summary count : 3

Destination/Mask Proto Pre Cost NextHop Interface

11.0.0.0/8 Static 60 0 0.0.0.0 NULL0

11.0.0.0/16 Static 60 0 0.0.0.0 NULL0

11.0.0.0/24 Static 60 0 0.0.0.0 NULL0

# Display brief information about the routes to the destination IP address 11.0.0.1 with mask length 20.

<Sysname> display ip routing-table 11.0.0.1 20

Summary count : 2

Destination/Mask Proto Pre Cost NextHop Interface

11.0.0.0/8 Static 60 0 0.0.0.0 NULL0

11.0.0.0/16 Static 60 0 0.0.0.0 NULL0

# Display brief information about the routes to the destination IP address 11.0.0.1 with the default mask length for class A networks.

<Sysname> display ip routing-table 11.0.0.1 longer-match

Summary count : 3

Destination/Mask Proto Pre Cost NextHop Interface

11.0.0.0/8 Static 60 0 0.0.0.0 NULL0

11.0.0.0/16 Static 60 0 0.0.0.0 NULL0

11.0.0.0/24 Static 60 0 0.0.0.0 NULL0

# Display brief information about the routes to the destination IP address 11.0.0.1 with mask length 20.

<Sysname> display ip routing-table 11.0.0.1 20 longer-match

Summary count : 3

Destination/Mask Proto Pre Cost NextHop Interface

11.0.0.0/8 Static 60 0 0.0.0.0 NULL0

11.0.0.0/16 Static 60 0 0.0.0.0 NULL0

11.0.0.0/24 Static 60 0 0.0.0.0 NULL0

# Display brief information about the routes to destination addresses in the range of 1.1.1.0 to 5.5.5.0.

<Sysname> display ip routing-table 1.1.1.0 to 5.5.5.0

Summary count : 5

Destination/Mask Proto Pre Cost NextHop Interface

1.1.1.1/32 Direct 0 0 127.0.0.1 InLoop0

3.3.3.0/24 Direct 0 0 3.3.3.1 XGE3/0/2

3.3.3.1/32 Direct 0 0 127.0.0.1 InLoop0

4.4.4.0/24 Direct 0 0 4.4.4.1 XGE3/0/1

4.4.4.1/32 Direct 0 0 127.0.0.1 InLoop0

For descriptions about the command output, see Table 1.

# Display fast reroute information about the routes to the destination IP address 3.3.3.3 with mask length 32.

<Sysname> display ip routing-table fast-reroute 3.3.3.3 32

Summary count : 1

Destination/Mask Proto Pre Cost NextHop Interface

3.3.3.3/32 Static 60 0 1.1.1.2 XGE3/0/1

2.1.1.2 XGE3/0/2

For descriptions about the command output, see Table 1.

# Display detailed information about the routes to the destination IP address 1.2.3.4.

<Sysname> display ip routing-table 1.2.3.4 verbose

Summary count : 1

Destination: 1.2.3.4/32

Protocol: BGP instance test

Process ID: 0

SubProtID: 0x1 Age: 00h00m37s

FlushedAge: 15h28m49s

Cost: 0 Preference: 255

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 200

NibID: 0x15000000 LastAs: 200

AttrID: 0x0

BkAttrID: 0x0 Neighbor: 192.168.47.2

Flags: 0x10060 OrigNextHop: 192.168.47.2

Label: NULL RealNextHop: 192.168.47.2

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: Ten-GigabitEthernet3/0/1

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: Ten-GigabitEthernet3/0/1

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

For descriptions about the command output, see Table 2.

display ip routing-table prefix-list

Use display ip routing-table prefix-list to display routes permitted by an IP prefix list.

Syntax

display ip routing-table [ vpn-instance vpn-instance-name ] prefix-list prefix-list-name [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

prefix-list-name: Specifies an IP prefix list by its name, a case-sensitive string of 1 to 63 characters.

verbose: Displays detailed information about all routes permitted by the IP prefix list. If you do not specify this keyword, the command displays brief information about active routes permitted by the IP prefix list.

Usage guidelines

If the specified IP prefix list does not exist, the command displays information about all routes.

Examples

# Create an IP prefix list named test to permit the route 1.1.1.0/24.

<Sysname> system-view

[Sysname] ip prefix-list test permit 1.1.1.0 24

# Display brief information about the active route permitted by the IP prefix list.

[Sysname] display ip routing-table prefix-list test

Summary count : 1

Destination/Mask Proto Pre Cost NextHop Interface

1.1.1.0/24 Direct 0 0 1.1.1.2 XGE3/0/2

For descriptions about the command output, see Table 1.

# Display detailed information about all routes permitted by the IP prefix list.

[Sysname] display ip routing-table prefix-list test verbose

Summary count : 1

Destination: 1.1.1.0/24

Protocol: Direct

Process ID: 0

SubProtID: 0x1 Age: 04h20m37s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NibID: 0x10000003 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x1008c OrigNextHop: 1.1.1.2

Label: NULL RealNextHop: 1.1.1.2

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: Ten-GigabitEthernet3/0/2

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: Ten-GigabitEthernet3/0/2

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

For descriptions about the command output, see Table 2.

display ip routing-table protocol

Use display ip routing-table protocol to display information about routes installed by a protocol.

Syntax

display ip routing-table [ vpn-instance vpn-instance-name ] protocol protocol [ fast-reroute | inactive | verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

protocol: Specifies a routing protocol.

inactive: Displays information about inactive routes. If you do not specify this keyword, the command displays information about both active and inactive routes.

verbose: Displays detailed routing table information. If you do not specify this keyword, the command displays brief routing information.

fast-reroute: Displays fast reroute routing table information.

Examples

# Display brief information about direct routes in the public network.

<Sysname> display ip routing-table protocol direct

Summary count : 9

Direct Routing table status : <Active>

Summary count : 9

Destination/Mask Proto Pre Cost NextHop Interface

0.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0

127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0

127.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0

127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0

127.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0

192.168.80.0/24 Direct 0 0 192.168.80.10 XGE3/0/1

192.168.80.0/32 Direct 0 0 192.168.80.10 XGE3/0/1

192.168.80.10/32 Direct 0 0 127.0.0.1 InLoop0

192.168.80.255/32 Direct 0 0 192.168.80.10 XGE3/0/1

Direct Routing table status : <Inactive>

Summary count : 0

For descriptions about the command output, see Table 1.

# Display information about static routes in the public network.

<Sysname> display ip routing-table protocol static

Summary count : 1

Static Routing table status : <Active>

Summary count : 0

Static Routing table status : <Inactive>

Summary count : 1

Destination/Mask Proto Pre Cost NextHop Interface

3.0.0.0/8 Static 60 0 2.2.2.2 XGE3/0/1

For descriptions about the command output, see Table 1.

# Display fast reroute information about static routes in the public network.

<Sysname> display ip routing-table protocol static fast-reroute

Destinations : 2 Routes : 2

Destination/Mask Proto Pre Cost NextHop Interface

3.3.3.3/32 Static 60 0 1.1.1.2 XGE3/0/1

2.1.1.2 XGE3/0/2

4.4.4.4/32 Static 60 0 1.1.1.2 XGE3/0/1

2.1.1.2 XGE3/0/2

For descriptions about the command output, see Table 1.

# Display detailed information about all BGP routes in the public network.

<Sysname> display ip routing-table protocol bgp verbose

Summary count : 1

Destination: 1.1.1.2/32

Protocol: BGP instance default

Process ID: 0

SubProtID: 0x6 Age: 00h03m54s

FlushedAge: 15h28m49s

Cost: 0 Preference: 255

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 200

NibID: 0x16000000 LastAs: 200

AttrID: 0x0

BkAttrID: 0x0 Neighbor: 192.168.47.2

Flags: 0x10060 OrigNextHop: 192.168.47.2

Label: NULL RealNextHop: 192.168.47.2

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: Ten-GigabitEthernet3/0/1

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: Ten-GigabitEthernet3/0/1

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

For descriptions about the command output, see Table 2.

display ip routing-table record

Use display ip routing-table record to display IPv4 route entry records.

Syntax

display ip routing-table record flush [ delete | update ] [ verbose ]

display ip routing-table record notify [ delete | update ] [ verbose ]

display ip routing-table record receive [ add | delete | update ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

flush: Displays the records for the route entries issued by the RIB to the FIB.

notify: Displays the records for the route entries notified by the RIB to the routing protocol.

receive: Displays the records for the route entries received by the RIB from the routing protocol.

add: Displays the records for the added route entries.

delete: Displays the records for the deleted route entries.

update: Displays the records for the updated route entries. If you specify the flush or notify keyword, the system takes added route entries as updated route entries when displaying the associated records.

verbose: Displays detailed information about IPv4 route entry records. If you do not specify this keyword, the command displays only brief information about IPv4 route entry records.

Usage guidelines

If you do not specify the add, delete, or update keyword, the command displays records for the added, deleted, and updated route entries.

When the system enters the level-1 memory threshold alarm status, it stops recording new route entry information. When the system enters the level-3 memory threshold alarm status, it clears existing route entry records. When the system exits the level-1 memory threshold alarm status, it starts recording new route entry information again.

Examples

# Display brief information about the records for the route entries issued by the RIB to the FIB.

<Sysname> display ip routing-table record flush

Total number of records: 2

Date Time Action Destination/Mask/VNID/Vrf

210907 15:38:50:961 update 200.0.0.0/24/0x111000000/default-vrf

210907 15:40:13:331 delete 200.0.0.0/24/0x0/default-vrf

Table 3 Command output

Field	Description
Total number of records	Total number of route entry records.
Date	Date when a record was generated.
Time	Time when the record was generated.
Action	Action on the route entry in the record: · update. · delete.
Destination	Destination address.
Mask	Mask length.
VNID	VN entry ID.
Vrf	Name of the VPN instance to which the route belongs. If the route belongs to the public network, this field displays default-vrf.

# Display detailed information about the records for the updated route entries issued by the RIB to the FIB.

<Sysname> display ip routing-table record flush update verbose

Total number of records: 1

Limit of records: 1000

Time: 210907 15:38:50:961 Action: update

Destination: 200.0.0.0/24

VrfIndex: 0 VrfName: default-vrf

SrcVrfIndex: 0 PriNibID: 0x0

OrigAs: 0 LastAs: 0

VNID: 0x111000000 AttrId: 0xffffffff

Flags: 0x10020000 ExtFlags: 0x0

Label: 0xffffffff BkLabel: 0xffffffff

LabelType: None InstanceId: 0

IpPrecedence: 65535 QosLocalId: 65535

TrafficIndex: 65535 UserID: 0x0

Table 4 Command output

Field	Description
Total number of records	Total number of route entry records.
Limit of records	Maximum number of route entry records.
Time	Date and time when a record was generated.
Action	Action on the route entry in the record: · update. · delete.
Destination	Destination address and mask length.
VrfIndex	VPN instance index.
VrfName	Name of the VPN instance to which the route belongs. If the route belongs to the public network, this field displays default-vrf.
SrcVrfIndex	Index of the source VPN instance for the copied route.
PriNibID	SRv6 forwarding entry index.
OrigAs	Original AS number.
LastAs	Last AS number.
VNID	VN entry ID.
AttrId	Route attribute ID.
Flags	Flags of the route.
ExtFlags	Extended flags of the route.
Label	Label.
BkLabel	Backup label.
LabelType	Protocol generated the labels. Values include: · None—No label. · BGP—BGP protocol. · LDP—LDP protocol. · SLSP—SLSP protocol. · OSPF—OSPF protocol. · ISIS—IS-IS protocol. · UNR—User network route. · Unknown—Unknown protocol.
InstanceId	ID of the multi-instance process.
IpPre	IP preference.
QosLocalID	Local QoS ID.
TrafficIndex	Traffic index. This field displays N/A when the value is invalid.
UserID	Access user ID.
SID Type	SID type.
VsiIndex	Index of the VSI to which the EVPN SRv6 SID belongs.
LinkId	Link ID of the L2VPN End.DX2 SID.
ArgLen	Arguments field length.

# Display brief information about the records for the route entries notified by the RIB to the routing protocol.

<Sysname> display ip routing-table record notify

Total number of records: 3

Date Time Action Destination/Mask/NibID/Vrf

210907 15:38:50:961 update 200.0.0.0/24/0x11000000/default-vrf

210907 15:39:46:496 update 200.0.0.0/24/0x11000000/default-vrf

210907 15:39:51:825 update 200.0.0.0/24/0x11000000/default-vrf

Table 5 Command output

Field	Description
Total number of records	Total number of route entry records.
Date	Date when a record was generated.
Time	Time when the record was generated.
Action	Action on the route entry in the record: · update. · delete.
Destination	Destination address.
Mask	Mask length.
NibID	ID of the next hop.
Vrf	Name of the VPN instance to which the route belongs. If the route belongs to the public network, this field displays default-vrf.

# Display detailed information about the records for the deleted route entries notified by the RIB to the routing protocol.

<Sysname> display ip routing-table record notify delete verbose

Total number of records: 1

Limit of records: 1000

Time: 210908 09:22:11:460 Action: delete

Destination: 200.0.0.0/8

TableID: 0x2 NibID: 0x0

ActCnt: 0 InactNibID: 0x0

VrfIndex: 0 VrfName: default-vrf

OldProtocol: STATIC NewProtocol: UnSpec

Flags: 0xc00 ExtFlags: 0x22

Table 6 Command output

Field	Description
Total number of records	Total number of route entry records.
Limit of records	Maximum number of route entry records.
Time	Date and time when a record was generated.
Action	Action on the route entry in the record: · add. · update. · delete.
Destination	Destination address and mask length.
TableID	ID of the routing table for the route.
NibID	Next hop ID.
ActCnt	Number of active routes using the route prefix.
InactNibID	Next hop ID of the inactive route reported to MPLS.
VrfIndex	VPN instance index.
VrfName	Name of the VPN instance to which the route belongs. If the route belongs to the public network, this field displays default-vrf.
OldProtocol	Routing protocol reported by the route the previous time.
NewProtocol	Routing protocol reported by the route the current time.
Flags	Flags of the route.
ExtFlags	Extended flags of the route.

# Display brief information about the records for the route entries received by the RIB from the routing protocol.

<Sysname> display ip routing-table record receive

Total number of records: 3

Date Time Action Proto Destination/Mask/NibID/Vrf

210907 15:38:50:957 add STATIC 200.0.0.0/24/0x11000000/default-vrf

210907 15:39:51:825 update STATIC 200.0.0.0/24/0x11000000/default-vrf

210907 15:40:13:329 delete STATIC 200.0.0.0/24/0x11000000/default-vrf

Table 7 Command output

Field	Description
Total number of records	Total number of route entry records.
Date	Date when a record was generated.
Time	Time when the record was generated.
Action	Action on the route entry: · add. · update. · delete.
Protocol	Routing protocol discovered the route.
Destination	Destination address.
Mask	Mask length.
PrefixLength	IPv6 address prefix length.
NibID	ID of the next hop.
Vrf	Name of the VPN instance to which the route belongs. If the route belongs to the public network, this field displays default-vrf.

# Display detailed information about the records for the added route entries received by the RIB from the routing protocol.

<Sysname> display ip routing-table record receive add verbose

Total number of records: 1

Limit of records: 1000

Time: 210907 15:38:50:957 Action: add

Destination: 200.0.0.0/24

TableID: 0x2 ProcessID: 0

VrfIndex: 0 VrfName: default-vrf

Protocol: STATIC SubProtID: 0x1

NibID: 0x11000000 NewNibID: N/A

AttrID: 0xffffffff BkAttrID: 0xffffffff

Flags: 0x60 ExtFlags: 0x0

ResetFlags: 0x0 ModFlags: 0x0

Label: 0xffffffff BkLabel: 0xffffffff

SRLabel: 0xffffffff BkSRLabel: 0xffffffff

InLabel: 0xffffffff SIDIndex: 0xffffffff

CommID: 0x8000000 Tag: 0

Cost: 0 Preference: 60

IpPre: N/A QosLocalID: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SID Type: N/A

SID: N/A

BkSID: N/A

Table 8 Command output

Field	Description
Total number of records	Total number of route entry records.
Limit of records	Maximum number of route entry records.
Time	Date and time when a record was generated.
Action	Action on the route entry: · add. · update. · delete.
Destination	Destination address and mask length.
TableID	Routing table ID of the route entry.
ProcessID	Process ID.
VrfIndex	VPN instance index.
VrfName	Name of the VPN instance to which the route belongs. If the route belongs to the public network, this field displays default-vrf.
Protocol	Routing protocol discovered the route.
SubProtID	Routing subprotocol ID.
NibID	Next hop ID.
NewNibID	ID of the updated next hop. This field displays N/A if the attribute is not available.
AttrID	Route attribute ID.
BkAttrID	Attribute ID for the backup route. This field displays the attribute ID for only the backup route added to the IP routing table through BGP.
Flags	Flags of the route.
ExtFlags	Extended flags of the route.
ResetFlags	Reset flags of the route upon an update. This field displays 1 if any bit in the Flags field is changed.
ModFlags	Modified flags of the route.
Label	Label.
BkLabel	Backup label.
SRLabel	SR label.
BkSRLabel	Backup SR label.
InLabel	Incoming label of the route.
SIDIndex	SID index value.
CommID	Common informatin entry ID of the route.
Tag	Route tag.
Cost	Cost of the route.
Preference	Preference of the route.
IpPre	IP precedence.
QosLocalID	Local QoS ID.
Connector	BGP Connector attribute. This field displays N/A if the attribute is not available. In inter-AS option B MDT-based MVPN, the value for this field is the source PE address carried in the VPN IPv4 route exchanged between BGP peers. For more information about the BGP connector attribute, see multicast VPN in IP Multicast Configuration Guide.
PathID	Path ID.
UserID	Access user ID.
SID Type	SID type. If the route does not have an SID, this field displays N/A.
SID	Primary SID. If no primary SID is available, this field displays N/A.
BkSID	Backup SID. If no backup SID is available, this field displays N/A.

‌

display ip routing-table statistics

Use display ip routing-table statistics to display IPv4 route or route prefix statistics.

Syntax

display ip routing-table [ all-routes | all-vpn-instance | vpn-instance vpn-instance-name ] [ prefix ] statistics

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

all-routes: Specifies the public network and all VPN instances.

all-vpn-instance: Specifies all VPN instances.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters.

prefix: Displays IPv4 route prefix statistics. If you do not specify this keyword, the command displays IPv4 route statistics.

Usage guidelines

If you do not specify any parameters, this command displays IPv4 route statistics for the public network.

Examples

# Display IPv4 route statistics for the public network.

<Sysname> display ip routing-table statistics

Total prefixes: 15 Active prefixes: 15

Proto Routes Active Added Deleted

DIRECT 12 12 30 18

STATIC 3 3 5 2

UNR 0 0 0 0

RIP 0 0 0 0

OSPF 0 0 0 0

IS-IS 0 0 0 0

LISP 0 0 0 0

EIGRP 0 0 0 0

BGP 0 0 0 0

Total 15 15 35 20

# Display IPv4 route statistics for the public network and all VPN instances.

<Sysname> display ip routing-table all-routes statistics

Total prefixes: 11 Active prefixes: 11

Proto Routes Active Added Deleted

DIRECT 8 8 8 0

STATIC 3 3 5 2

UNR 0 0 0 0

RIP 0 0 0 0

OSPF 0 0 0 0

IS-IS 0 0 0 0

LISP 0 0 0 0

EIGRP 0 0 0 0

BGP 0 0 0 0

Total 11 11 13 2

# Display IPv4 route statistics for VPN instance vpn1.

<Sysname> display ip routing-table vpn-instance vpn1 statistics

Total prefixes: 11 Active prefixes: 11

Proto Routes Active Added Deleted

DIRECT 8 8 8 0

STATIC 3 3 5 2

UNR 0 0 0 0

RIP 0 0 0 0

OSPF 0 0 0 0

IS-IS 0 0 0 0

LISP 0 0 0 0

EIGRP 0 0 0 0

BGP 0 0 0 0

Total 11 11 13 2

# Display IPv4 route statistics for all VPN instances.

<Sysname> display ip routing-table all-vpn-instance statistics

Total prefixes: 11 Active prefixes: 11

Proto Routes Active Added Deleted

DIRECT 8 8 8 0

STATIC 3 3 5 2

UNR 0 0 0 0

RIP 0 0 0 0

OSPF 0 0 0 0

IS-IS 0 0 0 0

LISP 0 0 0 0

EIGRP 0 0 0 0

BGP 0 0 0 0

Total 11 11 13 2

# Display IPv4 route prefix statistics for the public network.

<Sysname> display ip routing-table prefix statistics

Proto Prefixes Active Added Deleted

DIRECT 7 7 7 0

STATIC 0 0 0 0

UNR 0 0 0 0

RIP 1 0 1 0

OSPF 0 0 0 0

IS-IS 0 0 0 0

LISP 0 0 0 0

EIGRP 0 0 0 0

BGP 0 0 0 0

Total 8 7 8 0

Table 9 Command output

Field	Description
Proto	Protocol that installed the route or route prefix.
Routes	Number of routes installed by the protocol.
Prefixes	Number of route prefixes installed by the protocol.
Active	Number of active routes or route prefixes.
Added	Number of routes or route prefixes added to the routing table after the router started up or the routing table was cleared most recently.
Deleted	Number of routes or route prefixes marked as deleted, which will be cleared after a period.
Total	Total number of routes or route prefixes.

display ip routing-table summary

Use display ip routing-table summary to display brief routing table information, including maximum number of ECMP routes, maximum number of active routes, and number of remaining active routes.

Syntax

display ip routing-table [ vpn-instance vpn-instance-name ] summary

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

Examples

# Display brief routing table information for the public network.

<Sysname> display ip routing-table summary

Max ECMP: 32

Max Active Route: 262144

Remain Active Route: 262126

# Display brief routing table information for the MPLS L3VPN instance vpn1.

<Sysname> display ip routing-table vpn-instance vpn1 summary

Max ECMP: 32

Max Active Route: 262144

Remain Active Route: 262134

Threshold value percentage of max active routes: 100%

Table 10 Command output

Field	Description
Max ECMP	Maximum number of ECMP routes supported by the system.
Max Active Route	Maximum number of supported routes.
Remain Active Route	Number of the remaining inactive routes.
Threshold value xxx	Alarm threshold of active routes specified by using the routing-table limit command in a VPN instance: · Threshold value of active routes alert—This field is displayed when the alarm threshold is specified by using the routing-table limit number simply-alert command. When the number of active routes exceeds the alarm threshold, the system logs the event and sends traps but still accepts active routes. · Threshold value percentage of max active routes—This field is displayed when the alarm threshold is specified by using the routing-table limit number warn-threshold command, in the range of 1 to 100 in percentage. When the percentage of active routes exceeds the alarm threshold, the system logs the event and sends traps but still accepts active routes. If the number of active routes reaches the maximum number, no more routes can be added. The percentage of active routes equals the number of active routes divided by the maximum number of active routes supported in a VPN instance, and multiplied by 100.

‌

display ipv6 rib attribute

Use display ipv6 rib attribute to display route attribute information in the IPv6 RIB.

Syntax

display ipv6 rib attribute [ attribute-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

attribute-id: Specifies a route attribute by its ID, a hexadecimal string in the range of 0 to ffffffff.

Examples

# Display route attribute information in the IPv6 RIB.

<Sysname> display ipv6 rib attribute

Total number of attribute(s): 1

Detailed information of attribute 0x9:

Flag: 0x0

Protocol: BGP4+ instance default

Address family: IPv6

Reference count: 0

Local preference: 0

Ext-communities number: 0

Ext-communities value: N/A

Ext-comm-ipv6 number: 1

Ext-comm-ipv6 value: <RT Import: 303::3:9>

Communities number: 0

Communities value: N/A

AS-path number: 0

AS-path value: N/A

For command output, see Table 14.

display ipv6 rib graceful-restart

Use display ipv6 rib graceful-restart to display IPv6 RIB GR state information.

Syntax

display ipv6 rib graceful-restart

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display IPv6 RIB GR state information.

<Sysname> display ipv6 rib graceful-restart

RIB GR state : Phase2-calculation end

RCOM GR state : Flush end

Protocol GR state:

No. Protocol Lifetime FD State Start/End

--------------------------------------------------

1 DIRECT 900 29 End No/No

2 STATIC 900 32 End No/No

3 ISISV6 900 30 End No/No

4 BGP4+ instance default

900 31 End No/No

5 BGP4+ instance ebcdefg

900 32 End No/No

For command output, see Table 15.

display ipv6 rib nib

Use display ipv6 rib nib to display next hop information in the IPv6 RIB.

Syntax

display ipv6 rib nib [ self-originated ] [ nib-id ] [ verbose ]

display ipv6 rib nib [ sub-nib nib-id ] [ verbose ]

display ipv6 rib nib protocol protocol [ fast-reroute ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

self-originated: Displays information about next hops of self-originated routes in the IPv6 RIB.

sub-nib nib-id: Specifies a sub-NIB by its ID to display information about its parent NIB.

nib-id: Specifies a NIB by its ID, a hexadecimal string in the range of 0 to ffffffff.

verbose: Displays detailed next hop information in the IPv6 RIB. If you do not specify this keyword, the command displays brief next hop information in the IPv6 RIB.

protocol protocol: Specifies a protocol by its name.

fast-reroute: Displays next hop information about fast rerouting.

Examples

# Display brief next hop information in the IPv6 RIB.

<Sysname> display ipv6 rib nib

Total number of nexthop(s): 151

NibID: 0x20000000 Sequence: 0

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: ::

IFIndex: 0x111 LocalAddr: ::

MemberPort: 0x0

TopoNthp: Invalid ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: ::

NibID: 0x20000001 Sequence: 1

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: ::1

IFIndex: 0x112 LocalAddr: ::1

MemberPort: 0x0

TopoNthp: Invalid ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: ::

...

# Display detailed next hop information in the IPv6 RIB.

<Sysname> display ipv6 rib nib verbose

Total number of nexthop(s): 151

NibID: 0x20000000 Sequence: 0

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: ::

IFIndex: 0x111 LocalAddr: ::

MemberPort: 0x0

TopoNthp: Invalid ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: ::

RefCnt: 4 FlushRefCnt: 1

Flag: 0x84 Version: 1

ExtFlag: 0x0

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: ::

RelyDepth: 0 RealNexthop: ::

Interface: NULL0 LocalAddr: ::

TunnelCnt: 0 Vrf: default-vrf

TunnelID: N/A Topology:

Weight: 0 Flags: 0x0

SRPolicyNID: 4294967295 SRInterface:

ColorWeight: 0 Locator: N/A

MemberPort: N/A

NibID: 0x20000001 Sequence: 1

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: ::1

IFIndex: 0x112 LocalAddr: ::1

MemberPort: 0x0

TopoNthp: Invalid ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: ::

RefCnt: 4 FlushRefCnt: 1

Flag: 0x84 Version: 1

ExtFlag: 0x0

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: ::1

RelyDepth: 0 RealNexthop: ::1

Interface: InLoop0 LocalAddr: ::1

TunnelCnt: 0 Vrf: default-vrf

TunnelID: N/A Topology:

Weight: 0 Flags: 0x0

SRPolicyNID: 4294967295 SRInterface:

ColorWeight: 0 Locator: N/A

MemberPort: N/A

...

For command output, see Table 16 and Table 17.

display ipv6 rib nib record

Use display ipv6 rib nib record to display next hop records in the IPv6 RIB.

Syntax

display ipv6 rib nib record flush [ delete | update ] [ verbose ]

display ipv6 rib nib record receive [ add | delete | update ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

flush: Displays the records for the next hops issued by the IPv6 RIB to the FIB.

receive: Displays the records for the next hops received by the IPv6 RIB from the routing protocol.

add: Displays the records for the added next hops.

delete: Displays the records for the deleted next hops.

update: Displays the records for the updated next hops. If you specify the flush keyword, the system takes added next hops as updated next hops when displaying the associated records.

verbose: Displays detailed information about next hop records. If you do not specify this keyword, the command displays only brief information about next hop records.

Usage guidelines

If you do not specify the add, delete, or update keyword, the command displays records for the added, deleted, and updated next hops.

When the system enters the level-1 memory threshold alarm status, it stops recording new next hop information. When the system enters the level-3 memory threshold alarm status, it clears existing next hop records. When the system exits the level-1 memory threshold alarm status, it starts recording new next hop information again.

Examples

# Display brief information about the records for the next hops issued by the IPv6 RIB to the FIB.

<Sysname> display ipv6 rib nib record flush

Total number of records: 2

Date Time Action VNID

210908 15:31:55:364 update 0x20000000

210908 15:31:55:364 update 0x120000001

For descriptions about the command output, see Table 18.

# Display detailed information about the records for the updated next hops issued by the IPv6 RIB to the FIB.

<Sysname> display ipv6 rib nib record flush update verbose

Total number of records: 2

Limit of records: 1000

Time: 210908 15:31:55:364 Action: update

NibID: 0x20000000 VNID: 0x20000000

Sequence: 0 Version: 1

Flags: 0x80 ExtFlags: 0x0

RefCnt: 4 FlushRefCnt: 1

Type: 0xd

VrfIndex: 0 Nexthop: ::

IfIndex: 1410 LocalAddr: ::

ExtType: 0x0 NibInstance: IFM

UserKey0: 0x0 UserKey1: 0x0

NewUK0: 0x0 NewUK1: 0x0

NewUK2: 0x0 NewUK3: 0x0

NewUK4: 0x0 NewUK5: 0x0

NewUK6: 0x0 NewUK7: 0x0

SIDIndex: 0x0 SrPolicyName:

Color: 0 OriNexthop: ::

COFlag: 0x0 Locator: N/A

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: ::

RelyDepth: 0 RealNexthop: ::

Interface: 258 LocalAddr: ::

VrfIndex: 0 Topology:

Weight: 0 Flags: 0x800

SRPolicyNID: 4294967295 SRInterface: 0

ColorWeight: 0 Locator: N/A

MemberPort: 0 SRL2Interface: 0

Time: 210908 15:31:55:364 Action: update

NibID: 0x20000001 VNID: 0x120000001

Sequence: 1 Version: 1

Flags: 0x80 ExtFlags: 0x0

RefCnt: 4 FlushRefCnt: 1

Type: 0x1

VrfIndex: 0 Nexthop: ::1

IfIndex: 1410 LocalAddr: ::1

ExtType: 0x0 NibInstance: IFM

UserKey0: 0x0 UserKey1: 0x0

NewUK0: 0x0 NewUK1: 0x0

NewUK2: 0x0 NewUK3: 0x0

NewUK4: 0x0 NewUK5: 0x0

NewUK6: 0x0 NewUK7: 0x0

SIDIndex: 0x0 SrPolicyName:

Color: 0 OriNexthop: ::

COFlag: 0x0 Locator: N/A

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: ::

RelyDepth: 0 RealNexthop: ::

Interface: 258 LocalAddr: ::

VrfIndex: 0 Topology:

Weight: 0 Flags: 0x800

SRPolicyNID: 4294967295 SRInterface: 0

ColorWeight: 0 Locator: N/A

MemberPort: 0 SRL2Interface: 0

For descriptions about the command output, see Table 19.

# Display brief information about the records for the next hops received by the IPv6 RIB from the routing protocol.

<Sysname> display ipv6 rib nib record receive

Total number of records: 3

Date Time Action NibID NibInstance

210908 10:45:35:211 add 0x21000000 USR

210908 10:45:35:215 update 0x21000000 USR

210908 10:49:47:785 delete 0x21000000 USR

For descriptions about the command output, see Table 20.

# Display detailed information about the records for the added next hops received by the IPv6 RIB from the routing protocol.

<Sysname> display ipv6 rib nib record receive add verbose

Total number of records: 1

Limit of records: 1000

Time: 210928 14:39:14:147 Action: add

NibID: 0x20000000 Sequence: 0

NibInstance: IFM Version: 1

Flags: 0x0 UsrData: 0xffffffffffffffff

Type: 0x1 ExtType: 0x0

VrfIndex: 0 VrfName: default-vrf

InstanceId: 0 Nexthop: ::1

IfIndex: 1410 LocalAddr: ::1

UserKey0: 0x0 UserKey1: 0x0

NewUK0: 0x0 NewUK1: 0x0

NewUK2: 0x0 NewUK3: 0x0

NewUK4: 0x0 NewUK5: 0x0

NewUK6: 0x0 NewUK7: 0x0

Color: 0 COFlag: 0x0

BandWidth: 0 Weight: 0

ProtNibID: 0xffffffff NibFlags: 0x0

SIDIndex: 0x0 SrPolicyName:

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: ::1

RelyDepth: 0 RealNexthop: ::1

Interface: 1410 LocalAddr: ::1

VrfIndex: 0 Topology:

Weight: 0 Flags: 0x0

SRPolicyNID: 4294967295 SRInterface: 0

ColorWeight: 0 Locator: N/A

MemberPort: 0 SRL2Interface: 0

For descriptions about the command output, see Table 21.

display ipv6 route-direct nib

Use display ipv6 route-direct nib to display next hop information for IPv6 direct routes.

Syntax

display ipv6 route-direct nib [ nib-id ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

nib-id: Specifies a NIB by its ID, a hexadecimal string in the range of 0 to ffffffff.

verbose: Displays detailed next hop information for IPv6 direct routes. If you do not specify this keyword, the command displays brief next hop information for IPv6 direct routes.

Examples

# Display brief next hop information for IPv6 direct routes.

<Sysname> display ipv6 route-direct nib

Total number of nexthop(s): 115

NibID: 0x20000000 Sequence: 0

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: ::

IFIndex: 0x111 LocalAddr: ::

MemberPort: 0x0

TopoNthp: Invalid ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: ::

NibID: 0x20000001 Sequence: 1

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: ::1

IFIndex: 0x112 LocalAddr: ::1

MemberPort: 0x0

TopoNthp: Invalid ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: ::

...

# Display detailed next hop information for IPv6 direct routes.

<Sysname> display ipv6 route-direct nib verbose

Total number of nexthop(s): 115

NibID: 0x20000000 Sequence: 0

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: ::

IFIndex: 0x111 LocalAddr: ::

MemberPort: 0x0

TopoNthp: Invalid ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: ::

RefCnt: 1 FlushRefCnt: 0

Flag: 0x2 Version: 1

ExtFlag: 0x0

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: ::

RelyDepth: 0 RealNexthop: ::

Interface: NULL0 LocalAddr: ::

TunnelCnt: 0 Vrf: default-vrf

TunnelID: N/A Topology:

Weight: 0 Flags: 0x0

SRPolicyNID: 4294967295 SRInterface:

ColorWeight: 0 Locator: N/A

MemberPort: N/A

NibID: 0x20000001 Sequence: 1

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: ::1

IFIndex: 0x112 LocalAddr: ::1

MemberPort: 0x0

TopoNthp: Invalid ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: ::

RefCnt: 1 FlushRefCnt: 0

Flag: 0x2 Version: 1

ExtFlag: 0x0

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: ::1

RelyDepth: 0 RealNexthop: ::1

Interface: InLoop0 LocalAddr: ::1

TunnelCnt: 0 Vrf: default-vrf

TunnelID: N/A Topology:

Weight: 0 Flags: 0x0

SRPolicyNID: 4294967295 SRInterface:

ColorWeight: 0 Locator: N/A

MemberPort: N/A

...

For command output, see Table 22 and Table 23.

display ipv6 routing-table

Use display ipv6 routing-table to display IPv6 routing table information.

Syntax

display ipv6 routing-table [ all-vpn-instance | vpn-instance vpn-instance-name ] [ priority { critical | high | low | medium } ] [ verbose ]

display ipv6 routing-table all-routes

display ipv6 routing-table [ all-vpn-instance | vpn-instance vpn-instance-name ] fast-reroute

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

all-vpn-instance: Displays IPv6 routing table information for all VPN instances.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters.

all-routes: Displays IPv6 routing table information for the public network and all VPN instances.

fast-reroute: Displays fast reroute routing table information.

Usage guidelines

If you do not specify any parameters, this command displays IPv6 routing table information for the public network, excluding fast reroute routing table information.

Examples

# Display brief information about all active routes in the public network.

<Sysname> display ipv6 routing-table

Destinations : 3 Routes : 3

Destination: ::1/128 Protocol : Direct

NextHop : ::1 Preference: 0

Interface : InLoop0 Cost : 0

Destination: 5000::1:0:1/128 Protocol : SRv6

NextHop : ::1 Preference: 4

Interface : policy1 Cost : 0

Destination: FE80::/10 Protocol : Direct

NextHop : :: Preference: 0

Interface : InLoop0 Cost : 0

# Display brief information about active routes in the IPv6 routing table for the public network and all VPN instances.

<Sysname> display ipv6 routing-table all-routes

VPN instance: public instance

Destinations : 3 Routes : 3

Destination: ::1/128 Protocol : Direct

NextHop : ::1 Preference: 0

Interface : InLoop0 Cost : 0

Destination: 5000::1:0:1/128 Protocol : SRv6

NextHop : ::1 Preference: 4

Interface : policy1 Cost : 0

Destination: FE80::/10 Protocol : Direct

NextHop : :: Preference: 0

Interface : InLoop0 Cost : 0

VPN instance: vpn1

Destinations : 3 Routes : 3

Destination: ::1/128 Protocol : Direct

NextHop : ::1 Preference: 0

Interface : InLoop0 Cost : 0

Destination: 1:2::3:4/128 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

Destination: 5000::1:0:1/128 Protocol : SRv6

NextHop : ::1 Preference: 4

Interface : policy1 Cost : 0

# Display brief IPv6 routing table information for all VPN instances.

<Sysname> display ipv6 routing-table all-vpn-instance

VPN instance: vpn1

Destinations : 2 Routes : 2

Destination: ::1/128 Protocol : Direct

NextHop : ::1 Preference: 0

Interface : InLoop0 Cost : 0

Destination: 1:2::3:4/128 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

VPN instance: vpn2

Destinations : 1 Routes : 1

Destination: ::1/128 Protocol : Direct

NextHop : ::1 Preference: 0

Interface : InLoop0 Cost : 0

# Display brief IPv6 fast reroute information in the public network.

<Sysname> display ipv6 routing-table fast-reroute

Destinations : 1 Routes : 1

Destination: 3::/64 Protocol : Static

NextHop : 11::2 Preference: 60

Interface : XGE3/0/1 Cost : 0

Destination: 3::/64 Protocol :

NextHop : 12::2 Preference:

Interface : XGE3/0/2 Cost :

Table 11 Command output

Field	Description
VPN instance	Public network and VPN instance to which the IPv6 routing table belongs. For the public network, this filed displays public instance. For a VPN instance, this command displays the name of the instance.
Destinations	Number of destination addresses.
Routes	Number of routes.
Destination	IPv6 address and prefix of the destination network or host.
NextHop	Next hop address of the route.
Preference	Preference of the route.
Interface	Output interface for packets to be forwarded along the route. (If the protocol is SRv6 and the forwarding tunnel is SRv6 TE policy, this field displays the policy name.)
Protocol	Protocol that installed the route.
Cost	Cost of the route.
Summary count	Number of routes.

# Display detailed information about all routes in the public network.

<Sysname> display ipv6 routing-table verbose

Destinations : 3 Routes : 3

Destination: ::1/128

Protocol: Direct

Process ID: 0

SubProtID: 0x0 Age: 19h23m02s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000000 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: ::

Flags: 0x10004 OrigNextHop: ::1

Label: NULL RealNextHop: ::1

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: InLoopBack0

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: InLoopBack0

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

Destination: 12::/96

Protocol: Direct

Process ID: 0

SubProtID: 0x0 Age: 00h01m47s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000003 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: ::

Flags: 0x10080 OrigNextHop: ::

Label: NULL RealNextHop: ::

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: Ten-GigabitEthernet3/0/2

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: Ten-GigabitEthernet3/0/2

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

Destination: 5000::1:0:1/128

Protocol: SRv6

Process ID: 0

SubProtID: 0x0 Age: 00h01m47s

FlushedAge: 15h28m49s

Cost: 0 Preference: 4

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000002 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: ::

Flags: 0x10000 OrigNextHop: ::1

Label: NULL RealNextHop: ::1

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: policy1

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: NULL0

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: End NID: 0x80300001

FlushNID: 0x80300001 BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

# Display detailed IPv6 routing table information for all VPN instances.

<Sysname> display ipv6 routing-table all-vpn-instance verbose

VPN instance: vpn1

Destinations : 3 Routes : 3

Destination: ::1/128

Protocol: Direct

Process ID: 0

SubProtID: 0x0 Age: 19h23m02s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000000 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: ::

Flags: 0x10004 OrigNextHop: ::1

Label: NULL RealNextHop: ::1

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: InLoopBack0

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: InLoopBack0

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

Destination: 12::1/128

Protocol: Direct

Process ID: 0

SubProtID: 0x0 Age: 00h01m45s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000000 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: ::

Flags: 0x10004 OrigNextHop: ::1

Label: NULL RealNextHop: ::1

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: Ten-GigabitEthernet3/0/2

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: Ten-GigabitEthernet3/0/2

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

Destination: 5000::1:0:1/128

Protocol: SRv6

Process ID: 0

SubProtID: 0x0 Age: 00h01m47s

FlushedAge: 15h28m49s

Cost: 0 Preference: 4

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000002 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: ::

Flags: 0x10000 OrigNextHop: ::1

Label: NULL RealNextHop: ::1

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: policy1

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: NULL0

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: End NID: 0x80300001

FlushNID: 0x80300001 BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

Table 12 Command output

Field	Description
VPN instance	Public network and VPN instance to which the IPv6 routing table belongs. For the public network, this filed displays public instance. For a VPN instance, this command displays the name of the instance.
Destination	IPv6 address and prefix of the destination network or host.
Protocol	Protocol that installed the route.
SubProtID	ID of the subprotocol for routing.
Age	Time for which the route has been in the routing table.
FlushedAge	Time for which the route has been flushed to the FIB.
Cost	Cost of the route.
Preference	Preference of the route.
IpPre	IP precedence.
QosLocalID	Local QoS ID.
Tag	Tag of the route.
State	Route status: · Active—Active unicast route. · Adv—Route that can be advertised. · Inactive—Inactive route. · NoAdv—Route that the router is not allowed to advertise. · Vrrp—Routes generated by VRRP. · Nat—Routes generated by NAT. · TunE—Tunnel.
OrigTblID	Original routing table ID.
OrigVrf	Original VPN instance to which the route belongs. This field displays default-vrf if the route is on the public network.
TableID	ID of the routing table.
OrigAs	Original AS number.
NibID	ID of the next hop.
LastAs	Last AS number.
AttrID	Attribute ID.
BkAttrID	Attribute ID of the backup route. This field displays only the attribute ID of the backup route added by BGP to the IP routing table.
Neighbor	Address of the neighbor determined by the routing protocol.
Flags	Flags of the route.
OrigNextHop	Next hop address of the route.
RealNextHop	Real next hop of the route.
BkLabel	Backup label.
BkNexthop	Backup next hop.
SRLabel	SR label.
Interface	Output interface for packets to be forwarded along the route. (If the protocol is SRv6 and the forwarding tunnel is SRv6 TE policy, this field displays the policy name.)
BkSRLabel	Backup SR label.
BkInterface	Backup output interface. (If the protocol is SRv6 and the forwarding tunnel is SRv6 TE policy, this field displays the policy name.)
Tunnel ID	Tunnel ID
IPInterface	IP output interface for packets to be forwarded along the route.
BkTunnel ID	Backup tunnel ID.
BkIPInterface	Backup IP output interface.
InLabel	Incoming label of the route.
ColorInterface	Output interface recursed by an SR-MPLS TE policy or SRv6 TE policy.
SIDIndex	SID index value.
BkColorInterface	Backup output interface recursed by an SR-MPLS TE policy or SRv6 TE policy.
FtnIndex	Index of the FTN entry.
TunnelInterface	Output tunnel interface.
TrafficIndex	Traffic index in the range of 1 to 64. This field displays N/A when the value is invalid.
BkTunnelInterface	Backup output tunnel interface.
Connector	BGP connector attribute exchanged between BGP peers along with a VPN IPv4 route. The value of the attribute is the IP address of the remote PE device. The BGP connector attribute is used for MD VPN. This field displays N/A if BGP connector attribute is not supported.
PathID	Path ID.
Summary count	Number of routes.
UserID	Access user ID.
SRTunnelID	SR tunnel ID.
SID Type	This field is not supported in the current software version. SID type. If the route does not have an SID, this field displays N/A.
NID	Index of the Next Hop Label Forwarding Entry (Next Hop Label Forwarding Entry) flushed by the routing protocol.
FlushNID	Index of the NHLFE flushed to the FIB.
BkNID	Index of the backup NHLFE flushed by the routing protocol.
BkFlushNID	Index of the backup NHLFE flushed to the FIB.
StatFlags	Flags for SRv6 traffic statistics.
SID	Primary Segment Identifier (SID). If no primary SID is available, this field displays N/A.
BkSID	Backup SID. If no backup SID is available, this field displays N/A.
CommBlockLen	Common prefix length in the locator.
Priority	Convergence priority of the route: · Critical. · High. · Medium. · Low.
MemberPort	Number of a member port in an aggregation group. If this attribute is not available, this field displays N/A.

‌

display ipv6 routing-table acl

Use display ipv6 routing-table acl to display routing information permitted by an IPv6 basic ACL.

Syntax

display ipv6 routing-table [ vpn-instance vpn-instance-name ] acl ipv6-acl-number [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ipv6-acl-number: Specifies a basic IPv6 ACL by its number in the range of 2000 to 2999.

verbose: Displays detailed information about all routes permitted by the basic IPv6 ACL. If you do not specify this keyword, the command displays only brief information about active routes permitted by the basic IPv6 ACL.

Usage guidelines

When you specify an IPv6 ACL, follow these restrictions and guidelines:

· If the specified IPv6 ACL does not exist or does not have any rules, the command displays information about all IPv6 routes.

· If you specify the vpn-instance keyword for an ACL rule, the ACL rule will not take effect.

Examples

# Display brief information about active routes permitted by IPv6 ACL 2000.

<Sysname> display ipv6 routing-table acl 2000

Summary count : 5

Destination : ::1/128 Protocol : Direct

NextHop : ::1 Preference: 0

Interface : InLoop0 Cost : 0

Destination: 12::/96 Protocol : Direct

NextHop : :: Preference: 0

Interface : XGE3/0/2 Cost : 0

Destination: 12::1/128 Protocol : Direct

NextHop : ::1 Preference: 0

Interface : InLoop0 Cost : 0

Destination: FF::11/128 Protocol : BGP4+

NextHop : 12::2 Preference: 255

Interface : XGE3/0/2 Cost : 0

Destination: FE80::/10 Protocol : Direct

NextHop : :: Preference: 0

Interface : InLoop0 Cost : 0

For descriptions about the command output, see Table 11.

# Display detailed information about all routes permitted by IPv6 ACL 2000.

<Sysname> display ipv6 routing-table acl 2000 verbose

Summary count : 5

Destination: ::1/128

Protocol: Direct

Process ID: 0

SubProtID: 0x0 Age: 19h29m12s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000000 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: ::

Flags: 0x10004 OrigNextHop: ::1

Label: NULL RealNextHop: ::1

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: InLoopBack0

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: InLoopBack0

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

Destination: 12::/96

Protocol: Direct

Process ID: 0

SubProtID: 0x0 Age: 00h07m57s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000003 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: ::

Flags: 0x10080 OrigNextHop: ::

Label: NULL RealNextHop: ::

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: Ten-GigabitEthernet3/0/2

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: Ten-GigabitEthernet3/0/2

BkTunnel ID: Invalid IPBkInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

Destination: 12::1/128

Protocol: Direct

Process ID: 0

SubProtID: 0x0 Age: 00h07m55s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000000 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: ::

Flags: 0x10004 OrigNextHop: ::1

Label: NULL RealNextHop: ::1

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: InLoopBack0

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: InLoopBack0

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

Destination: FF::11/128

Protocol: BGP4+ instance default

Process ID: 0

SubProtID: 0x6 Age: 00h06m43s

FlushedAge: 15h28m49s

Cost: 0 Preference: 255

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 200

NibID: 0x26000000 LastAs: 200

AttrID: 0x1

BkAttrID: 0x1 Neighbor: 12::2

Flags: 0x10060 OrigNextHop: 12::2

Label: NULL RealNextHop: 12::2

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: Ten-GigabitEthernet3/0/2

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: Ten-GigabitEthernet3/0/2

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

Destination: FE80::/10

Protocol: Direct

Process ID: 0

SubProtID: 0x0 Age: 19h29m12s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000002 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: ::

Flags: 0x10084 OrigNextHop: ::

Label: NULL RealNextHop: ::

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: InLoopBack0

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: InLoopBack0

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

For descriptions about the command output, see Table 12.

display ipv6 routing-table ipv6-address

Use display ipv6 routing-table ipv6-address to display information about routes to an IPv6 destination address.

Use display ipv6 routing-table ipv6-address1 to ipv6-address2 to display information about routes to a range of IPv6 destination addresses.

Syntax

display ipv6 routing-table [ vpn-instance vpn-instance-name ] ipv6-address [ prefix-length ] [ longer-match ] [ verbose ]

display ipv6 routing-table [ vpn-instance vpn-instance-name ] ipv6-address1 to ipv6-address2 [ verbose ]

display ipv6 routing-table [ vpn-instance vpn-instance-name ] fast-reroute ipv6-address [ prefix-length ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ipv6-address: Specifies a destination IPv6 address.

prefix-length: Specifies the prefix length in the range of 0 to 128.

longer-match: Displays the route entries that meet the matching rules as described in the usage guidelines.

ipv6-address1 to ipv6-address2: Specifies a destination IPv6 address range.

fast-reroute: Displays fast reroute routing table information.

Usage guidelines

Executing the command with different parameters yields different output.

· display ipv6 routing-table ipv6-address

¡ The system ANDs the entered destination IPv6 address with the prefix length in each active route entry.

¡ The system ANDs the destination IPv6 address in each active route entry with the prefix length in the entry.

If the two operations yield the same result for an entry, the entry is displayed.

· display ipv6 routing-table ipv6-address prefix-length

¡ The system ANDs the entered destination IPv6 address with the entered prefix length.

¡ The system ANDs the destination IPv6 address in each active route entry with the entered prefix length.

If the two operations yield the same result for an entry with a prefix length not greater than the entered prefix length, the entry is displayed.

· display ipv6 routing-table ipv6-address longer-match

If you do not specify the prefix-length argument, the command yields the same result as the display ipv6 routing-table command.

· display ipv6 routing-table ipv6-address prefix-length longer-match

¡ The system ANDs the entered destination IPv6 address with the entered prefix length.

¡ The system ANDs the destination IPv6 address in each active route entry with the entered prefix length.

If the two operations yield the same result for multiple entries, all the entries are displayed.

· display ipv6 routing-table ipv6-address1 to ipv6-address2

The system displays route entries with destinations in the range of ipv6-address1/128 to ipv6-address2/128.

Examples

# Display brief information about the routes to the destination IPv6 address 10::1 127.

<Sysname> display ipv6 routing-table 10::1 127

Summary count: 3

Destination: 10::/64 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

Destination: 10::/68 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

Destination: 10::/120 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

# Display brief information about the routes to the destination IPv6 address 10::1 with prefix length 127.

<Sysname> display ipv6 routing-table 10::1 127 longer-match

Summary count : 3

Destination: 10::/64 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

Destination: 10::/68 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

Destination: 10::/120 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

# Display brief information about the routes to destination addresses in the range of 100:: to 300::.

<Sysname> display ipv6 routing-table 100:: to 300::

Summary count : 3

Destination: 100::/64 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

Destination: 200::/64 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

Destination: 300::/64 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

For descriptions about the command output, see Table 11.

# Display brief fast reroute information about the routes to the destination IPv6 address 3:: with a prefix length of 32.

<Sysname> display ipv6 routing-table fast-reroute 3:: 32

Summary count : 1

Destination: 3::/32 Protocol : Static

NextHop : 11::2 Preference: 60

Interface : XGE3/0/1 Cost : 0

Destination: 3::/32 Protocol :

NextHop : 12::2 Preference:

Interface : XGE3/0/2 Cost :

# Display detailed information about the routes to destination IPv6 addresses 1:2::3:4/128.

<Sysname> display ipv6 routing-table 1:2::3:4 128 verbose

Summary count : 1

Destination: 1:2::3:4/128

Protocol: BGP4+ instance abc

Process ID: 0

SubProtID: 0x1 Age: 00h01m14s

FlushedAge: 15h28m49s

Cost: 0 Preference: 255

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x1 OrigAs: 200

NibID: 0x26000000 LastAs: 200

AttrID: 0x0

BkAttrID: 0x0 Neighbor: 2:2::3:4

Flags: 0x10060 OrigNextHop: 2:2::3:4

Label: NULL RealNextHop: 2:2::3:4

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: Ten-GigabitEthernet3/0/1

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: Ten-GigabitEthernet3/0/1

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

For descriptions about the command output, see Table 12.

Related commands

display ipv6 routing-table

display ipv6 routing-table prefix-list

Use display ipv6 routing-table prefix-list to display information about IPv6 routes permitted by an IPv6 prefix list.

Syntax

display ipv6 routing-table [ vpn-instance vpn-instance-name ] prefix-list prefix-list-name [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

prefix-list-name: Specifies an IPv6 prefix list by its name, a case-sensitive string of 1 to 63 characters.

verbose: Displays detailed information about all IPv6 routes permitted by the IPv6 prefix list. If you do not specify this keyword, the command displays brief information about active IPv6 routes permitted by the IPv6 prefix list.

Usage guidelines

If the specified IPv6 prefix list does not exist, the command displays information about all routes.

Examples

# Create an IPv6 prefix list named test to permit the prefix ::1/128.

<Sysname> system-view

[Sysname] ipv6 prefix-list test permit ::1 128

# Display brief information about the active IPv6 route permitted by the IPv6 prefix list.

[Sysname] display ipv6 routing-table prefix-list test

Summary count : 1

Destination: ::1/128 Protocol : Direct

NextHop : ::1 Preference: 0

Interface : InLoop0 Cost : 0

For descriptions about the command output, see Table 11.

# Display detailed information about all routes permitted by the IPv6 prefix list.

[Sysname] display ipv6 routing-table prefix-list test verbose

Summary count : 1

Destination: ::1/128

Protocol: Direct

Process ID: 0

SubProtID: 0x0 Age: 08h57m19s

FlushedAge: 15h28m49s

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000000 LastAs: 0

AttrID: 0xffffffff

BkAttrID: 0xffffffff Neighbor: ::

Flags: 0x10004 OrigNextHop: ::1

Label: NULL RealNextHop: ::1

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: InLoopBack0

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: InLoopBack0

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

For descriptions about the command output, see Table 12.

display ipv6 routing-table protocol

Use display ipv6 routing-table protocol to display information about IPv6 routes installed by a protocol.

Syntax

display ipv6 routing-table [ vpn-instance vpn-instance-name ] protocol protocol [ fast-reroute | inactive | verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

protocol: Specifies a routing protocol.

inactive: Displays information about inactive routes. If you do not specify this keyword, the command displays information about both active and inactive routes.

verbose: Displays detailed routing table information. If you do not specify this keyword, the command displays brief routing information.

fast-reroute: Displays fast reroute routing table information.

Examples

# Display brief information about IPv6 direct routes in the public network.

<Sysname> display ipv6 routing-table protocol direct

Summary count : 2

Direct Routing table status : <Active>

Summary count : 2

Destination: ::1/128 Protocol : Direct

NextHop : ::1 Preference: 0

Interface : InLoop0 Cost : 0

Destination: FE80::/10 Protocol : Direct

NextHop : :: Preference: 0

Interface : InLoop0 Cost : 0

Direct Routing table status : <Inactive>

Summary count : 0

For descriptions about the command output, see Table 11.

# Display information about IPv6 static routes in the public network.

<Sysname> display ipv6 routing-table protocol static

Summary count : 3

Static Routing table status : <Active>

Summary count : 3

Destination: 2::2/128 Protocol : Static

NextHop : fe80::2 Preference: 60

Interface : XGE3/0/2 Cost : 0

Destination: 2::2/128 Protocol : Static

NextHop : fe80::3 Preference: 60

Interface : XGE3/0/2 Cost : 0

Destination: 3::3/128 Protocol : Static

NextHop : 2::2 Preference: 60

Interface : XGE3/0/2 Cost : 0

Static Routing table status : <Inactive>

Summary count : 0

For descriptions about the command output, see Table 11.

# Display fast reroute information about IPv6 static routes in the public network.

<Sysname> display ipv6 routing-table protocol static fast-reroute

Destinations : 1 Routes : 1

Destination: 3::/32 Protocol : Static

NextHop : 11::2 Preference: 60

Interface : XGE3/0/1 Cost : 0

Destination: 3::/64 Protocol : Static

NextHop : 12::2 Preference: 60

Interface : XGE3/0/2 Cost : 0

# Display detailed information about all IPv6 BGP routes in the public network.

<Sysname> display ipv6 routing-table protocol bgp4+ verbose

Summary count : 1

Destination: 22::22/128

Protocol: BGP4+ instance abc

Process ID: 0

SubProtID: 0x6 Age: 00h04m15s

FlushedAge: 15h28m49s

Cost: 0 Preference: 255

IpPre: N/A QosLocalID: N/A

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 200

NibID: 0x25000001 LastAs: 200

AttrID: 0x3

BkAttrID: 0x3 Neighbor: 121::2

Flags: 0x10060 OrigNextHop: 121::2

Label: NULL RealNextHop: 121::2

BkLabel: NULL BkNextHop: N/A

SRLabel: NULL Interface: Ten-GigabitEthernet3/0/1

BkSRLabel: NULL BkInterface: N/A

Tunnel ID: Invalid IPInterface: Ten-GigabitEthernet3/0/1

BkTunnel ID: Invalid BkIPInterface: N/A

InLabel: NULL ColorInterface: N/A

SIDIndex: NULL BkColorInterface: N/A

FtnIndex: 0x0 TunnelInterface: N/A

TrafficIndex: N/A BkTunnelInterface: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SRTunnelID: Invalid

SID Type: N/A NID: Invalid

FlushNID: Invalid BkNID: Invalid

BkFlushNID: Invalid StatFlags: 0x0

SID: N/A

BkSID: N/A

CommBlockLen: 0 Priority: Critical

MemberPort: N/A

For descriptions about the command output, see Table 12.

display ipv6 routing-table record

Use display ipv6 routing-table record to display IPv6 routing entry records.

Syntax

display ipv6 routing-table record flush [ delete | update ] [ verbose ]

display ipv6 routing-table record notify [ delete | update ] [ verbose ]

display ipv6 routing-table record receive [ add | delete | update ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

flush: Displays the records for the route entries issued by the IPv6 RIB to the FIB.

notify: Displays the records for the route entries notified by the IPv6 RIB to the routing protocol.

receive: Displays the records for the route entries received by the IPv6 RIB from the routing protocol.

add: Displays the records for the added route entries.

delete: Displays the records for the deleted route entries.

verbose: Displays detailed information about IPv6 route entry records. If you do not specify this keyword, the command displays only brief information about IPv6 route entry records.

Usage guidelines

If you do not specify the add, delete, or update keyword, the command displays records for the added, deleted, and updated route entries.

Examples

# Display brief information about the records for the route entries issued by the IPv6 RIB to the FIB.

<Sysname> display ipv6 routing-table record flush

Total number of records: 2

Date Time Action Destination/PrefixLength/VNID/Vrf

210908 09:33:21:996 update 1001::/64/0x520000004/default-vrf

210908 09:33:23:386 update 1001::1/128/0x120000001/default-vrf

For descriptions about the command output, see Table 3.

# Display detailed information about the records for the updated route entries issued by the IPv6 RIB to the FIB.

<Sysname> display ipv6 routing-table record flush update verbose

Total number of records: 2

Limit of records: 1000

Time: 210908 09:33:21:996 Action: update

Destination: 1001::/64

VrfIndex: 0 VrfName: default-vrf

SrcVrfIndex: 0 PriNibID: 0x0

OrigAs: 0 LastAs: 0

VNID: 0x520000004

Flags: 0x10040000 ExtFlags: 0x0

Label: 0xffffffff BkLabel: 0xffffffff

IpPrecedence: 65535 QosLocalId: 65535

FlowIndex: 65535 UserID: 0x0

SID Type: 0 VsiIndex: 0xffffffff

LinkId: 0xffffffff ArgLen: 0

Time: 210908 09:33:23:386 Action: update

Destination: 1001::1/128

VrfIndex: 0 VrfName: default-vrf

SrcVrfIndex: 0 PriNibID: 0x0

OrigAs: 0 LastAs: 0

VNID: 0x120000001

Flags: 0x10040000 ExtFlags: 0x0

Label: 0xffffffff BkLabel: 0xffffffff

IpPrecedence: 65535 QosLocalId: 65535

FlowIndex: 65535 UserID: 0x0

SID Type: 0 VsiIndex: 0xffffffff

LinkId: 0xffffffff ArgLen: 0

For descriptions about the command output, see Table 4.

# Display brief information about the records for the route entries notified by the IPv6 RIB to the routing protocol.

<Sysname> display ipv6 routing-table record notify

Total number of records: 1

Date Time Action Destination/PrefixLength/NibID/Vrf

210908 10:47:03:698 update 2000::/64/0x21000000/default-vrf

For descriptions about the command output, see Table 5.

# Display detailed information about the records for the deleted route entries notified by the IPv6 RIB to the routing protocol.

<Sysname> display ipv6 routing-table record notify delete verbose

Total number of records: 1

Limit of records: 1000

Time: 210908 10:49:47:787 Action: delete

Destination: 2000::/64

TableID: 0xa NibID: 0x0

ActCnt: 0 InactNibID: 0x0

VrfIndex: 0 VrfName: default-vrf

OldProtocol: STATIC NewProtocol: UnSpec

RtFlags: 0xc00 ExtRtFlags: 0x22

For descriptions about the command output, see Table 6.

# Display brief information about the records for the route entries received by the IPv6 RIB from the routing protocol.

<Sysname> display ipv6 routing-table record receive

Total number of records: 1

Date Time Action Proto Destination/PrefixLength/NibID/Vrf

210908 09:33:23:385 add DIRECT 1001::1/128/0x20000001/default-vrf

For descriptions about the command output, see Table 7.

# Display detailed information about the records for the added route entries received by the IPv6 RIB from the routing protocol.

<Sysname> display ipv6 routing-table record receive add verbose

Total number of records: 1

Limit of records: 1000

Time: 210908 09:33:23:385 Action: add

Destination: 1001::1/128

TableID: 0xa ProcessID: 0

VrfIndex: 0 VrfName: default-vrf

Protocol: DIRECT SubProtID: 0x0

NibID: 0x20000001 NewNibID: N/A

AttrID: 0xffffffff BkAttrID: 0xffffffff

Flags: 0x4 ExtFlags: 0x0

ResetFlags: 0x0 ModFlags: 0x0

Label: 0xffffffff BkLabel: 0xffffffff

SRLabel: 0xffffffff BkSRLabel: 0xffffffff

InLabel: 0xffffffff SIDIndex: 0xffffffff

CommID: 0x5000001 Tag: 0

Cost: 0 Preference: 0

IpPre: N/A QosLocalID: N/A

Connector: N/A PathID: 0x0

UserID: 0x0 SID Type: N/A

SID: N/A

BkSID: N/A

For descriptions about the command output, see Table 8.

display ipv6 routing-table statistics

Use display ipv6 routing-table statistics to display IPv6 route or route prefix statistics.

Syntax

display ipv6 routing-table [ all-routes | all-vpn-instance | vpn-instance vpn-instance-name ] [ prefix ] statistics

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

all-routes: Specifies the public network and all VPN instances.

all-vpn-instance: Specifies all VPN instances.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters.

prefix: Displays IPv6 route prefix statistics. If you do not specify this keyword, the command displays IPv6 route statistics.

Usage guidelines

If you do not specify any parameters, this command displays IPv6 route statistics for the public network.

Examples

# Display IPv6 route statistics for the public network.

<Sysname> display ipv6 routing-table statistics

Total prefixes: 8 Active prefixes: 8

Proto Routes Active Added Deleted

DIRECT 5 5 5 0

STATIC 3 3 3 0

UNR 0 0 0 0

RIPng 0 0 0 0

OSPFv3 0 0 0 0

IS-ISv6 0 0 0 0

LISP 0 0 0 0

SRv6 0 0 0 0

BGP4+ 0 0 0 0

Total 8 8 8 0

# Display IPv6 route statistics for the public network and all VPN instances.

<Sysname> display ipv6 routing-table all-routes statistics

Total prefixes: 6 Active prefixes: 6

Proto Routes Active Added Deleted

DIRECT 3 3 3 0

STATIC 3 3 5 2

UNR 0 0 0 0

RIPng 0 0 0 0

OSPFv3 0 0 0 0

IS-ISv6 0 0 0 0

LISP 0 0 0 0

SRv6 0 0 0 0

BGP4+ 0 0 0 0

Total 6 6 8 2

# Display IPv6 route statistics for VPN instance vpn1.

<Sysname> display ipv6 routing-table vpn-instance vpn1 statistics

Total prefixes: 11 Active prefixes: 11

Proto Routes Active Added Deleted

DIRECT 8 8 8 0

STATIC 3 3 5 2

UNR 0 0 0 0

RIPng 0 0 0 0

OSPFv3 0 0 0 0

IS-ISv6 0 0 0 0

LISP 0 0 0 0

SRv6 0 0 0 0

BGP4+ 0 0 0 0

Total 11 11 13 2

# Display IPv6 route statistics for all VPN instances.

<Sysname> display ipv6 routing-table all-vpn-instance statistics

Total prefixes: 11 Active prefixes: 11

Proto Routes Active Added Deleted

DIRECT 8 8 8 0

STATIC 3 3 5 2

UNR 0 0 0 0

RIPng 0 0 0 0

OSPFv3 0 0 0 0

IS-ISv6 0 0 0 0

LISP 0 0 0 0

SRv6 0 0 0 0

BGP4+ 0 0 0 0

Total 11 11 13 2

# Display IPv6 route prefix statistics for the public network.

<Sysname> display ipv6 routing-table prefix statistics

Proto Prefixes Active Added Deleted

DIRECT 5 5 5 0

STATIC 1 1 1 0

UNR 0 0 0 0

RIPng 0 0 0 0

OSPFv3 0 0 0 0

IS-ISv6 0 0 0 0

LISP 0 0 0 0

SRv6 0 0 0 0

BGP4+ 0 0 0 0

Total 6 6 6 0

Table 13 Command output

Field	Description
Proto	Protocol that installed the route or route prefix.
Routes	Number of routes installed by the protocol.
Prefixes	Number of route prefixes installed by the protocol.
Active	Number of active routes or route prefixes.
Added	Number of routes or route prefixes added to the routing table after the router started up or the routing table was cleared most recently.
Deleted	Number of routes or route prefixes marked as deleted, which will be cleared after a period.
Total	Total number of routes or route prefixes.

display ipv6 routing-table summary

Use display ipv6 routing-table summary to display brief IPv6 routing table information, including maximum number of ECMP routes, maximum number of active routes, and number of remaining active routes.

Syntax

display ipv6 routing-table [ vpn-instance vpn-instance-name ] summary

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

Examples

# Display brief IPv6 routing table information for the public network.

<Sysname> display ipv6 routing-table summary

Max ECMP: 32

Max Active Route: 262144

Remain Active Route: 262126

For descriptions about the command output, see Table 10.

# Display brief IPv6 routing table information for the MPLS L3VPN instance vpn1.

<Sysname> display ipv6 routing-table vpn-instance vpn1 summary

Max ECMP: 32

Max Active Route: 262144

Remain Active Route: 262134

Threshold value of active routes alert: 65100

For descriptions about the command output, see Table 10.

display rib attribute

Use display rib attribute to display route attribute information in the RIB.

Syntax

display rib attribute [ attribute-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

attribute-id: Specifies a route attribute by its ID, a hexadecimal string in the range of 0 to ffffffff.

Examples

# Display route attribute information in the RIB.

<Sysname> display rib attribute

Total number of attribute(s): 10

Detailed information of attribute 0x0:

Flag: 0x0

Protocol: BGP instance default

Address family: IPv4

Reference count: 0

Act-RT reference count: 0

Flush flag: 0

Local preference: 0

Ext-communities number: 26

Ext-communities value: <RT: 1:1> <RT: 2:2> <RT: 3:3> <RT: 123.123.123.123:65535

> <RT: 1234567890:65535> <RT: 123.123.123.123:65534> <RT

: 4:4> <RT: 5:5> <RT: 6:6> <RT: 7:7> <RT: 8:8> <RT: 9:9>

<RT: 10:10> <RT: 10:1> <RT: 10:11> <RT: 10:12> <RT: 10:

13> <RT: 10:14> <RT: 10:15> <RT: 10:16> ...

Communities number: 0

Communities value: N/A

AS-path number: 0

AS-path value: N/A

SFlow AS-path length: 0

SFlow AS-path value: N/A

Detailed information of attribute 0x1:

Flag: 0x0

Protocol: BGP

Address family: IPv4

Reference count: 0

Act-RT reference count: 0

Flush flag: 0

Local preference: 0

Ext-communities number: 1

Ext-communities value: <RT: 1.1.1.1:2>

Ext-comm-ipv6 number: 1

Ext-comm-ipv6 value: <RT Import: 303::3:9>

Communities number: 0

Communities value: N/A

AS-path number: 0

AS-path value: N/A

SFlow AS-path length: 0

SFlow AS-path value: N/A

Table 14 Command output

Field	Description
Protocol	Protocol that generates the attribute.
Act-RT reference count	Reference count of active routes.
Flush flag	Flag of flushing route attribute information to the FIB: · 0—The route attribute information is not flushed to the FIB. · 1—The route attribute information is flushed to the FIB.
Ext-communities number	Number of the IPv4 extended community attribute values.
Ext-communities value	Values of the IPv4 extended community attribute. This field displays N/A when no values exist, and it can display a maximum of 20 values.
Ext-comm-ipv6 number	Number of the IPv6 extended community attribute values.
Ext-comm-ipv6 value	Values of the IPv6 extended community attribute. This field displays N/A when no values exist, and it can display a maximum of 20 values.
Communities number	Number of the COMMUNITY attribute values.
Communities value	Values of the COMMUNITY attribute. This field displays N/A when no values exist, and it can display a maximum of 20 values.
AS-path number	Number of ASs in the AS_PATH attribute.
AS-path value	Values of the AS_PATH attribute, including AS_SET, AS_SEQUENCE, confederation AS_SET, and confederation AS_SEQUENCE. This field displays N/A when no values exist, and it can display a maximum of 20 values.
SFlow AS-path length	This field is not supported in the current software version. Length of the sFlow AS-path attribute.
SFlow AS-path value	This field is not supported in the current software version. Value of the sFlow AS-path attribute. This field displays N/A if the length of the sFlow AS-path attribute is 0. This field can display a maximum of 20 characters.

display rib graceful-restart

Use display rib graceful-restart to display RIB GR state information.

Syntax

display rib graceful-restart

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display RIB GR state information.

<Sysname> display rib graceful-restart

RIB GR state : Phase2-calculation end

RCOM GR state : Flush end

Protocol GR state:

No. Protocol Lifetime FD State Start/End

--------------------------------------------------

1 DIRECT 900 30 End No/No

2 STATIC 900 34 End No/No

3 OSPF 900 36 End No/No

4 ISIS 900 32 End No/No

5 BGP instance abc

900 22 End No/No

6 BGP instance default

900 25 End No/No

7 LDP 900 35 End No/No

8 SLSP 900 29 End No/No

9 UNR instance UCM

900 33 End No/No

Table 15 Command output

Field	Description
RIB GR state	RIB GR status: · Start—GR starts. · IGP end—All IGP protocols complete GR. · VPN-triggering end—Optimal route selection triggered by VPN routes completes. · VPN-calculation end—Optimal VPN route selection completes. · Routing protocol end—All routing protocols complete GR. · NSR-calculation unfinished—NSR has not finished optimal route selection. · Triggering start—All triggered optimal route selection starts. · Triggering end—All triggered optimal route selection completes. · Phase1-calculation end—Optimal route selection phase 1 completes. · All end—All protocols complete GR. · Phase2-calculation end—Optimal route selection phase 2 completes.
RCOM GR state	RCOM GR status: · Start—GR starts. · VPN-calculation end—Optimal VPN route selection completes. · VPN-notification end—VPN routes have been delivered to the route management module. · Routing protocol end—All routing protocols complete GR. · NSR-calculation unfinished—NSR has not finished optimal route selection. · Phase1-calculation end—Optimal route selection phase 1 completes. · Notification end—All routes have been delivered to the route management module. · Phase2-calculation end—Optimal route selection phase 2 completes. · Flush start—Starts to flush routes to the FIB. · Flush end—Completes flushing routes to the FIB.
No.	Protocol number.
Lifetime	Lifetime (in seconds) of routes/labels in the RIB during GR.
FD	Handle between the protocol and the RIB.
State	Protocol GR state: · Init—Initialization state. · Listen—Listening state. · Idle. · Active. · Start—GR starts. · End—GR completes.
Start/End	Message sending state: · No—The message has not been sent. · Yes—The message has been sent.

display rib nib

Use display rib nib to display next hop information in the RIB.

Syntax

display rib nib [ self-originated ] [ nib-id ] [ verbose ]

display rib nib [ sub-nib nib-id ] [ verbose ]

display rib nib protocol protocol [ fast-reroute ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

self-originated: Displays information about next hops of self-originated routes in the RIB.

sub-nib nib-id: Specifies a sub-NIB by its ID to display information about its parent NIB.

nib-id: Specifies a NIB by its ID, a hexadecimal string in the range of 0 to ffffffff.

verbose: Displays detailed next hop information in the RIB. If you do not specify this keyword, the command displays brief next hop information in the RIB.

protocol protocol: Specifies a protocol by its name.

fast-reroute: Displays next hop information about fast rerouting.

Usage guidelines

If you do not specify any parameters, this command displays brief information about all next hops in the RIB.

Examples

# Display brief next hop information in the RIB.

<Sysname> display rib nib

Total number of nexthop(s): 176

NibID: 0x10000000 Sequence: 0

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: 0.0.0.0

IFIndex: 0x111 LocalAddr: 0.0.0.0

MemberPort: 0x0

TopoNthp: 0 ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: 0.0.0.0

NibID: 0x10000001 Sequence: 1

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: 127.0.0.1

IFIndex: 0x112 LocalAddr: 127.0.0.1

MemberPort: 0x0

TopoNthp: 0 ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: 0.0.0.0

NibID: 0x10000002 Sequence: 2

Type: 0x5 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: 127.0.0.1

IFIndex: 0x112 LocalAddr: 127.0.0.1

MemberPort: 0x0

TopoNthp: 0 ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: 0.0.0.0

NibID: 0x16000000 Sequence: 3

Type: 0x21 Flushed: No

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: 12.1.1.2

IFIndex: 0x0 LocalAddr: 0.0.0.0

MemberPort: 0x0

TopoNthp: 0 ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: 0.0.0.0

Instance: abc

...

Table 16 Command output

Field	Description
NibID	ID of the next hop.
Sequence	Sequence number of the next hop.
Type	Type of the next hop.
Flushed	Indicates whether the route with the next hop has been flushed to the FIB.
Age	Time when the next hop was updated most recently.
UserKey0	Reserved data 1.
UserKey1	Reserved data 2.
VrfNthp	Index of the VPN instance to which the next hop belongs. This field displays 0 if the next hop is on the public network.
Nexthop	Next hop address.
IFIndex	Interface index.
LocalAddr	Local interface address.
MemberPort	Index of a member port in an aggregation group.
NewUK0	New reserved data 1. This field is not displayed if the attribute is not available.
NewUK1	New reserved data 2. This field is not displayed if the attribute is not available.
NewUK2	New reserved data 3. This field is not displayed if the attribute is not available.
NewUK3	New reserved data 4. This field is not displayed if the attribute is not available.
NewUK4	New reserved data 5. This field is not displayed if the attribute is not available.
NewUK5	New reserved data 6. This field is not displayed if the attribute is not available.
NewUK6	New reserved data 7. This field is not displayed if the attribute is not available.
NewUK7	New reserved data 8. This field is not displayed if the attribute is not available.
NewUK8	New reserved data 9. This field is not displayed if the attribute is not available.
NewUK9	New reserved data 10. This field is not displayed if the attribute is not available.
NewUK10	New reserved data 11. This field is not displayed if the attribute is not available.
NewUK11	New reserved data 12. This field is not displayed if the attribute is not available.
NewUK12	New reserved data 13. This field is not displayed if the attribute is not available.
TopoNthp	Non-base topologies are not supported in the current software version. Index of the topology that contains the next hop. This field displays 0 if the next hop is on the IPv4 public network. This field displays Invalid if the next hop is on an IPv6 network, because the router does not support non-base topologies.
ExtType	Extension type of the next hop.
Color	Color extended community attribute.
COFlag	Flag of the color extended community attribute.
SIDIndex	SID index value.
SRPName	SR-MPLS TE policy name.
OriNexthop	Original next hop address of the route. If the route is obtained from a BGP UPDATE message, the address is the next hop IP address in the BGP UPDATE message.
Instance	BGP instance name.
SubNibID	ID of the sub-next hop.
SubSeq	Sequence number of the sub-next hop.
NthpCnt	Number of sub-next hops.
Samed	Number of the same sub-next hops.
NthpType	Type of the sub-next hop: · IP—IP forwarding. · MPLS—MPLS forwarding.

# Display detailed next hop information in the RIB.

<Sysname> display rib nib verbose

Total number of nexthop(s): 176

NibID: 0x10000000 Sequence: 0

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: 0.0.0.0

IFIndex: 0x111 LocalAddr: 0.0.0.0

MemberPort: 0x0

TopoNthp: 0 ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: 0.0.0.0

RefCnt: 6 FlushRefCnt: 2

Flag: 0x84 Version: 1

ExtFlag: 0x0

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: 0.0.0.0

RelyDepth: 0 RealNexthop: 0.0.0.0

Interface: NULL0 LocalAddr: 0.0.0.0

TunnelCnt: 0 Vrf: default-vrf

TunnelID: N/A Topology: base

Weight: 0 Flags: 0x0

SRPolicyNID: 4294967295 SRInterface:

ColorWeight: 0 Locator: N/A

MemberPort: N/A

NibID: 0x10000001 Sequence: 1

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: 127.0.0.1

IFIndex: 0x112 LocalAddr: 127.0.0.1

MemberPort: 0x0

TopoNthp: 0 ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: 0.0.0.0

RefCnt: 13 FlushRefCnt: 5

Flag: 0x84 Version: 1

ExtFlag: 0x0

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: 127.0.0.1

RelyDepth: 0 RealNexthop: 127.0.0.1

Interface: InLoop0 LocalAddr: 127.0.0.1

TunnelCnt: 0 Vrf: default-vrf

TunnelID: N/A Topology: base

Weight: 0 Flags: 0x0

SRPolicyNID: 4294967295 SRInterface:

ColorWeight: 0 Locator: N/A

MemberPort: N/A

NibID: 0x15000003 Sequence: 3

Type: 0x43 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x100010000 VrfNthp: 0

UserKey1: 0x0 Nexthop: 22.22.22.22

IFIndex: 0x0 LocalAddr: 0.0.0.0

MemberPort: 0x0

TopoNthp: 0 ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: 0.0.0.0

Instance: default

RefCnt: 9 FlushRefCnt: 3

Flag: 0x84 Version: 1

ExtFlag: 0x0

Policy: tnl-policy1

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: 22.22.22.22

RelyDepth: 1 RealNexthop: 13.1.1.2

Interface: XGE3/0/1 LocalAddr: 13.1.1.1

TunnelCnt: 1 Vrf: default-vrf

TunnelID: 1025 Topology: base

Weight: 0 Flags: 0x0

SRPolicyNID: 4294967295 SRInterface:

ColorWeight: 0 Locator: N/A

MemberPort: N/A

...

Table 17 Command output

Field	Description
NibID	ID of the next hop.
Sequence	Sequence number of the next hop.
Type	Type of the next hop.
Flushed	Indicates whether the route with the next hop has been flushed to the FIB.
Age	Time when the next hop was updated most recently.
UserKey0	Reserved data 1.
VrfNthp	Index of the VPN instance that the next hop belongs to. This field displays 0 if the next hop is on the public network.
UserKey1	Reserved data 2.
Nexthop	Next hop address.
IFIndex	Interface index.
LocalAddr	Local interface address.
MemberPort	Index of a member port in an aggregation group.
NewUK0	New reserved data 1. This field is not displayed if the attribute is not available.
NewUK1	New reserved data 2. This field is not displayed if the attribute is not available.
NewUK2	New reserved data 3. This field is not displayed if the attribute is not available.
NewUK3	New reserved data 4. This field is not displayed if the attribute is not available.
NewUK4	New reserved data 5. This field is not displayed if the attribute is not available.
NewUK5	New reserved data 6. This field is not displayed if the attribute is not available.
NewUK6	New reserved data 7. This field is not displayed if the attribute is not available.
NewUK7	New reserved data 8. This field is not displayed if the attribute is not available.
NewUK8	New reserved data 9. This field is not displayed if the attribute is not available.
NewUK9	New reserved data 10. This field is not displayed if the attribute is not available.
NewUK10	New reserved data 11. This field is not displayed if the attribute is not available.
NewUK11	New reserved data 12. This field is not displayed if the attribute is not available.
NewUK12	New reserved data 13. This field is not displayed if the attribute is not available.
TopoNthp	Non-base topologies are not supported in the current software version. Index of the topology that contains the next hop. This field displays 0 if the next hop is on the IPv4 public network. This field displays Invalid if the next hop is on an IPv6 network, because the router does not support non-base topologies.
ExtType	Extension type of the next hop.
Color	Color extended community attribute.
COFlag	Flag of the color extended community attribute.
SIDIndex	SID index value.
SRPName	SR-MPLS TE policy name.
OriNexthop	Original next hop address of the route. If the route is obtained from a BGP UPDATE message, the address is the next hop IP address in the BGP UPDATE message.
Instance	BGP instance name.
RefCnt	Reference count of the next hop.
FlushRefCnt	Reference count of the next hop that is flushed to the FIB.
Flag	Flag of the next hop.
Version	Version of the next hop.
ExtFlag	Extended flag of the next hop.
Policy	Tunnel policy name.
x nexthop (s)	Number of next hops.
PrefixIndex	Prefix index of the next hop for an ECMP route.
OrigNexthop	Original next hop.
RelyDepth	Recursion depth.
RealNexthop	Real next hop.
Interface	Output interface.
LocalAddr	Local interface address.
TunnelCnt	Number of tunnels after route recursion.
Vrf	VPN instance name. For the public network, this field displays default-vrf.
TunnelID	ID of the tunnel after route recursion.
Topology	Non-base topologies are not supported in the current software version. Topology name. The topology name for the IPv4 public network is base. This field is blank for IPv6, because IPv6 does not support non-base topologies.
Weight	ECMP route weight. This field displays 0 for non-ECMP routes.
Flags	Flags of the detailed next hop.
SRPolicyNID	NIB ID of the route obtained from an SR-MPLS TE policy through route recursion.
SRInterface	Output interface of the route obtained from the SR-MPLS TE policy through route recursion.
ColorWeight	Weight value of the color attribute in the SR-MPLS TE policy.
Locator	IPv6 prefix of the locator to which the SID belongs. If no locator is available, this field displays N/A.
MemberPort	Number of a member port in an aggregation group. If this attribute is not available, this field displays N/A.

‌

display rib nib record

Use display rib nib record to display next hop records in the RIB.

Syntax

display rib nib record flush [ delete | update ] [ verbose ]

display rib nib record receive [ add | delete | update ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

flush: Displays the records for the next hops issued by the RIB to the FIB.

receive: Displays the records for the next hops received by the RIB from the routing protocol.

add: Displays the records for the added next hops.

delete: Displays the records for the deleted next hops.

update: Displays the records for the updated next hops. If you specify the flush keyword, the system takes added next hops as updated next hops when displaying the associated records.

verbose: Displays detailed information about next hop records. If you do not specify this keyword, the command displays only brief information about next hop records.

Usage guidelines

If you do not specify the add, delete, or update keyword, the command displays records for the added, deleted, and updated next hops.

Examples

# Display brief information about the records for the next hops issued by the RIB to the FIB.

<Sysname> display rib nib record flush

Total number of records: 2

Date Time Action VNID

210908 15:31:58:753 update 0x10000000

210908 15:31:58:755 update 0x110000001

Table 18 Command output

Field	Description
Total number of records	Total number of next hop records.
Date	Date when a record was generated.
Time	Time when the record was generated.
Action	Action on the next hop in the record: · add. · update. · delete.
VNID	VN entry ID.

# Display detailed information about the records for the updated next hops issued by the RIB to the FIB.

<Sysname> display rib nib record flush update verbose

Total number of records: 1

Limit of records: 1000

Time: 210928 14:39:14:162 Action: update

NibID: 0x10000000 VNID: 0x10000000

Sequence: 0 Version: 1

Flag: 0x80 ExtFlags: 0x0

RefCnt: 5 FlushRefCnt: 1

Type: 0x1

VrfIndex: 0x0 Nexthop: 127.0.0.1

IfIndex: 1410 LocalAddr: 127.0.0.1

ExtType: 0x0 NibInstance: IFM

UserKey0: 0x0 UserKey1: 0x0

NewUK0: 0x0 NewUK1: 0x0

NewUK2: 0x0 NewUK3: 0x0

NewUK4: 0x0 NewUK5: 0x0

NewUK6: 0x0 NewUK7: 0x0

SIDIndex: 0x0 SrPolicyName:

Color: 0 OriNexthop: 0.0.0.0

COFlag: 0x0 Locator: N/A

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: 127.0.0.1

RelyDepth: 0 RealNexthop: 127.0.0.1

Interface: 1410 LocalAddr: 127.0.0.1

VrfIndex: 0 Topology: base

Weight: 0 Flags: 0x0

SRPolicyNID: 4294967295 SRInterface: 0

ColorWeight: 0 Locator: N/A

MemberPort: 0 SRL2Interface: 0

Table 19 Command output

Field	Description
Total number of records	Total number of next hop records.
Limit of records	Maximum number of next hop records.
Time	Date and time when a record was generated.
Action	Action on the next hop in the record: · update. · delete.
NibID	ID of the next hop.
VNID	VN entry ID.
Sequence	Sequence number of the next hop.
Version	Version of the next hop.
Flag	Flag of the next hop.
ExtFlags	Flags of extended next hop information.
RefCnt	Reference count of the next hop.
FlushRefCnt	Reference count of the next hop that is flushed to the FIB.
Type	Next hop type.
VrfIndex	VPN instance index.
Nexthop	Next hop address.
IfIndex	Output interface index.
LocalAddr	Local interface address.
ExtType	Extended type of the next hop.
NibInstance	Instance or protocol generated the next hop information: · IFM—Interface management instance. · USR—Static routing. · RIP—RIP or RIPng. · OSPF—OSPF or OSPFv3. · ISIS—IS-IS or IPv6 IS-IS. · LISP—LISP. · BGP—BGP or BGP4+. · RIB—IP routing table instance. · EVPN—EVPN instance. · EIGRP—EIGRP or EIGRPv6. · UNR—User network routing instance. · SRV6—SRv6. · None—Unknown or invalid instance.
UserKey0	Reserved data 1.
UserKey1	Reserved data 2.
NewUK0	New reserved data 1.
NewUK1	New reserved data 2.
NewUK2	New reserved data 3.
NewUK3	New reserved data 4.
NewUK4	New reserved data 5.
NewUK5	New reserved data 6.
NewUK6	New reserved data 7.
NewUK7	New reserved data 8.
SIDIndex	SID index value.
SrPolicyName	Name of an SR-MPLS TE policy.
Color	Color extended community attribute.
OriNexthop	Original next hop address of the route. If the route is obtained from a BGP UPDATE message, the address is the next hop IP address in the BGP UPDATE message.
COFlag	Flag of the color extended community attribute.
Locator	IPv6 prefix of the locator to which the SID belongs. If no locator is available, this field displays N/A.
SubType	Subtype of the parent NIB.
SubNibID	ID of the sub-next hop.
SubSeq	Sequence number of the sub-next hop.
NthpCnt	Number of sub-next hops.
Samed	Number of the same sub-next hops.
NthpType	Type of the sub-next hop: · IP—IP forwarding. · MPLS—MPLS forwarding.
x nexthop (s)	Number of next hops.
PrefixIndex	Prefix index of the next hop for an ECMP route.
OrigNexthop	Original next hop.
RelyDepth	Recursion depth.
RealNexthop	Real next hop.
Interface	Output interface.
Topology	Topology name. The topology name for the IPv4 public network is base. This field is blank for IPv6, because IPv6 does not support non-base topologies.
Weight	ECMP route weight. This field displays 0 for non-ECMP routes.
Flags	Flags of the current next hop.
SRPolicyNID	NIB ID of the route obtained from an SR-MPLS TE policy through route recursion.
SRInterface	Output interface of the route obtained from the SR-MPLS TE policy through route recursion.
ColorWeight	Weight value of the color attribute in the SR-MPLS TE policy.
Locator	IPv6 prefix of the locator to which the SID belongs. If no locator is available, this field displays N/A.
MemberPort	Index of a member port in an aggregation group. When this attribute is not available, the field displays 0.
SRL2Interface	Number of a member port in an aggregation group. When this attribute is not available, the field displays 0.

# Display brief information about the records for the next hops received by the RIB from the routing protocol.

<Sysname> display rib nib record receive

Total number of records: 2

Date Time Action NibID NibInstance

210907 14:42:09:471 add 0x10000003 IFM

210907 15:35:45:190 delete 0x10000003 IFM

Table 20 Command output

Field	Description
Total number of records	Total number of next hop records.
Date	Date when a record was generated.
Time	Time when the record was generated.
Action	Action on the next hop in the record: · add. · update. · delete.
NibID	ID of the next hop.
NibInstance	Instance or protocol generated the next hop information: · IFM—Interface management instance. · USR—Static routing. · RIP—RIP or RIPng. · OSPF—OSPF or OSPFv3. · ISIS—IS-IS or IPv6 IS-IS. · LISP—LISP. · BGP—BGP or BGP4+. · RIB—IP routing table instance. · EVPN—EVPN instance. · EIGRP—EIGRP or EIGRPv6. · UNR—User network routing instance. · SRV6—SRv6. · None—Unknown or invalid instance.

# Display detailed information about the records for the added next hops received by the RIB from the routing protocol.

<Sysname> display rib nib record receive add verbose

Total number of records: 1

Limit of records: 1000

Time: 210928 14:39:14:148 Action: add

NibID: 0x10000000 Sequence: 0

NibInstance: IFM Version: 1

Flag: 0x0 UsrData: 0xffffffffffffffff

Type: 0x1 ExtType: 0x0

VrfIndex: 0 VrfName: default-vrf

InstanceId: 0 Nexthop: 127.0.0.1

IfIndex: 1410 LocalAddr: 127.0.0.1

UserKey0: 0x0 UserKey1: 0x0

NewUK0: 0x0 NewUK1: 0x0

NewUK2: 0x0 NewUK3: 0x0

NewUK4: 0x0 NewUK5: 0x0

NewUK6: 0x0 NewUK7: 0x0

Color: 0 COFlag: 0x0

BandWidth: 0 Weight: 0

ProtNibID: 0xffffffff NibFlags: 0x0

SIDIndex: 0x0 SrPolicyName:

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: 127.0.0.1

RelyDepth: 0 RealNexthop: 127.0.0.1

Interface: 1410 LocalAddr: 127.0.0.1

VrfIndex: 0 Topology: base

Weight: 0 Flags: 0x0

SRPolicyNID: 4294967295 SRInterface: 0

ColorWeight: 0 Locator: N/A

MemberPort: 0 SRL2Interface: 0

Table 21 Command output

Field	Description
Total number of records	Total number of next hop records.
Limit of records	Maximum number of next hop records.
Time	Date and time when a record was generated.
Action	Action on the next hop in the record: · add. · update. · delete.
NibID	Next hop ID.
Sequence	Next hop sequence number.
NibInstance	Instance or protocol generated the next hop information: · IFM—Interface management instance. · USR—Static routing. · RIP—RIP or RIPng. · OSPF—OSPF or OSPFv3. · ISIS—IS-IS or IPv6 IS-IS. · LISP—LISP. · BGP—BGP or BGP4+. · RIB—IP routing table instance. · EVPN—EVPN instance. · EIGRP—EIGRP or EIGRPv6. · UNR—User network routing instance. · SRV6—SRv6. · None—Unknown or invalid instance.
Version	Version of the next hop.
Flag	Flag of the next hop.
UsrData	Protocol private data.
VrfIndex	VPN instance index.
VrfName	Name of the VPN instance to which the route belongs. If the route belongs to the public network, this field displays default-vrf.
Type	Next hop type.
Nexthop	Next hop address.
ExtType	Extended type of the next hop.
LocalAddr	Local interface address.
InstanceId	ID of the multi-instance process.
IfIndex	Interface index.
UserKey0	Reserved data 1.
UserKey1	Reserved data 2.
NewUK0	New reserved data 1.
NewUK1	New reserved data 2.
NewUK2	New reserved data 3.
NewUK3	New reserved data 4.
NewUK4	New reserved data 5.
NewUK5	New reserved data 6.
NewUK6	New reserved data 7.
NewUK7	New reserved data 8.
Color	Color extended community attribute.
COFlag	Flag of the color extended community attribute.
BandWidth	Bandwidth of the link associated with the next hop.
Weight	ECMP route weight. This field displays 0 for non-ECMP routes.
ProtNibID	Next hop ID carried by the protocol.
NibFlags	Flags of the next hop.
SIDIndex	SID index value.
SrPolicyName	SR-MPLS TE policy name.
SubType	Subtype of the parent NIB.
SubNibID	ID of the sub-next hop.
SubSeq	Sequence number of the sub-next hop.
NthpCnt	Number of sub-next hops.
Samed	Number of the same sub-next hops.
NthpType	Type of the sub-next hop: · IP—IP forwarding. · MPLS—MPLS forwarding.
x nexthop (s)	Number of next hops.
PrefixIndex	Prefix index of the next hop for an ECMP route.
OrigNexthop	Original next hop.
RelyDepth	Recursion depth.
RealNexthop	Real next hop.
Interface	Output interface.
Topology	Topology name. The topology name for the IPv4 public network is base. This field is blank for IPv6, because IPv6 does not support non-base topologies.
Flags	Flags of the detailed next hop.
SRPolicyNID	NIB ID of the route obtained from an SR-MPLS TE policy through route recursion.
SRInterface	Output interface of the route obtained from the SR-MPLS TE policy through route recursion.
ColorWeight	Weight value of the color attribute in the SR-MPLS TE policy.
Locator	IPv6 prefix of the locator to which the SID belongs. If no locator is available, this field displays N/A.
MemberPort	Index of a member port in an aggregation group. When this attribute is not available, the field displays 0.
SRL2Interface	Number of a member port in an aggregation group. When this attribute is not available, the field displays 0.

‌

display route-direct nib

Use display route-direct nib to display next hop information for direct routes.

Syntax

display route-direct nib [ nib-id ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

nib-id: Specifies a NIB by its ID, a hexadecimal string in the range of 0 to ffffffff.

verbose: Displays detailed next hop information for direct routes. If you do not specify this keyword, the command displays brief next hop information for direct routes.

Examples

# Display brief next hop information for direct routes.

<Sysname> display route-direct nib

Total number of nexthop(s): 116

NibID: 0x10000000 Sequence: 0

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: 0.0.0.0

IFIndex: 0x111 LocalAddr: 0.0.0.0

MemberPort: 0x0

TopoNthp: 0 ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: 0.0.0.0

NibID: 0x10000001 Sequence: 1

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: 127.0.0.1

IFIndex: 0x112 LocalAddr: 127.0.0.1

MemberPort: 0x0

TopoNthp: 0 ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: 0.0.0.0

...

Table 22 Command output

Field	Description
NibID	ID of the NIB.
Sequence	Sequence number of the NIB.
Type	Type of the NIB.
Flushed	Indicates whether the route with the NIB has been flushed to the FIB.
Age	Time when the next hop information was updated most recently.
UserKey0	Reserved data 1.
UserKey1	Reserved data 2.
VrfNthp	Index of the VPN instance to which the next hop belongs. This field displays 0 if the next hop is on the public network.
Nexthop	Next hop address.
IFIndex	Interface index.
LocalAddr	Local interface IP address.
MemberPort	Index of a member port in an aggregation group.
NewUK0	New reserved data 1. This field is not displayed if the attribute is not available.
NewUK1	New reserved data 2. This field is not displayed if the attribute is not available.
NewUK2	New reserved data 3. This field is not displayed if the attribute is not available.
NewUK3	New reserved data 4. This field is not displayed if the attribute is not available.
NewUK4	New reserved data 5. This field is not displayed if the attribute is not available.
NewUK5	New reserved data 6. This field is not displayed if the attribute is not available.
NewUK6	New reserved data 7. This field is not displayed if the attribute is not available.
NewUK7	New reserved data 8. This field is not displayed if the attribute is not available.
NewUK8	New reserved data 9. This field is not displayed if the attribute is not available.
NewUK9	New reserved data 10. This field is not displayed if the attribute is not available.
NewUK10	New reserved data 11. This field is not displayed if the attribute is not available.
NewUK11	New reserved data 12. This field is not displayed if the attribute is not available.
NewUK12	New reserved data 13. This field is not displayed if the attribute is not available.
TopoNthp	Non-base topologies are not supported in the current software version. Index of the topology that contains the next hop. This field displays 0 if the next hop is on the IPv4 public network. This field displays Invalid if the next hop is on an IPv6 network, because the router does not support non-base topologies.
ExtType	Extension type of the next hop.
Color	Color extended community attribute.
COFlag	Flag of the color extended community attribute.
SIDIndex	SID index value.
SRPName	SR-MPLS TE policy name.
OriNexthop	Original next hop address of the route. If the route is obtained from a BGP UPDATE message, the address is the next hop IP address in the BGP UPDATE message.

# Display detailed next hop information for direct routes.

<Sysname> display route-direct nib verbose

Total number of nexthop(s): 116

NibID: 0x10000000 Sequence: 0

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: 0.0.0.0

IFIndex: 0x111 LocalAddr: 0.0.0.0

MemberPort: 0x0

TopoNthp: 0 ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: 0.0.0.0

RefCnt: 2 FlushRefCnt: 0

Flag: 0x2 Version: 1

ExtFlag: 0x0

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: 0.0.0.0

RelyDepth: 0 RealNexthop: 0.0.0.0

Interface: NULL0 LocalAddr: 0.0.0.0

TunnelCnt: 0 Vrf: default-vrf

TunnelID: N/A Topology: base

Weight: 0 Flags: 0x0

SRPolicyNID: 4294967295 SRInterface:

ColorWeight: 0 Locator: N/A

MemberPort: N/A

NibID: 0x10000001 Sequence: 1

Type: 0x1 Flushed: Yes

Age: 00h01m50s

UserKey0: 0x0 VrfNthp: 0

UserKey1: 0x0 Nexthop: 127.0.0.1

IFIndex: 0x112 LocalAddr: 127.0.0.1

MemberPort: 0x0

TopoNthp: 0 ExtType: 0x0

Color: 0 COFlag: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: 0.0.0.0

RefCnt: 5 FlushRefCnt: 0

Flag: 0x2 Version: 1

ExtFlag: 0x0

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: 127.0.0.1

RelyDepth: 0 RealNexthop: 127.0.0.1

Interface: InLoop0 LocalAddr: 127.0.0.1

TunnelCnt: 0 Vrf: default-vrf

TunnelID: N/A Topology: base

Weight: 0 Flags: 0x0

SRPolicyNID: 4294967295 SRInterface:

ColorWeight: 0 Locator: N/A

MemberPort: N/A

...

Table 23 Command output

Field	Description
NibID	ID of the next hop.
Sequence	Sequence number of the next hop.
Type	Type of the next hop.
Flushed	Indicates whether the route with the next hop has been flushed to the FIB.
Age	Time when the next hop information was updated most recently.
UserKey0	Reserved data 1.
VrfNthp	Index of the VPN instance to which the next hop belongs. This field displays 0 if the next hop is on the public network.
UserKey1	Reserved data 2.
Nexthop	Next hop address.
IFIndex	Interface index.
LocalAddr	Local interface address.
MemberPort	Index of a member port in an aggregation group.
NewUK0	New reserved data 1. This field is not displayed if the attribute is not available.
NewUK1	New reserved data 2. This field is not displayed if the attribute is not available.
NewUK2	New reserved data 3. This field is not displayed if the attribute is not available.
NewUK3	New reserved data 4. This field is not displayed if the attribute is not available.
NewUK4	New reserved data 5. This field is not displayed if the attribute is not available.
NewUK5	New reserved data 6. This field is not displayed if the attribute is not available.
NewUK6	New reserved data 7. This field is not displayed if the attribute is not available.
NewUK7	New reserved data 8. This field is not displayed if the attribute is not available.
NewUK8	New reserved data 9. This field is not displayed if the attribute is not available.
NewUK9	New reserved data 10. This field is not displayed if the attribute is not available.
NewUK10	New reserved data 11. This field is not displayed if the attribute is not available.
NewUK11	New reserved data 12. This field is not displayed if the attribute is not available.
NewUK12	New reserved data 13. This field is not displayed if the attribute is not available.
TopoNthp	Non-base topologies are not supported in the current software version. Index of the topology that contains the next hop. This field displays 0 if the next hop is on the IPv4 public network. This field displays Invalid if the next hop is on an IPv6 network, because the router does not support non-base topologies.
ExtType	Extension type of the next hop.
Color	Color extended community attribute.
COFlag	Flag of the color extended community attribute.
SIDIndex	SID index value.
SRPName	SR-MPLS TE policy name.
OriNexthop	Original next hop address of the route. If the route is obtained from a BGP UPDATE message, the address is the next hop IP address in the BGP UPDATE message.
RefCnt	Reference count of the next hop.
FlushRefCnt	Reference count of the next hop that is flushed to the FIB.
Flag	Flag of the next hop.
Version	Version of the next hop.
ExtFlag	Extended flag of the next hop.
x nexthop(s)	Number of next hops.
PrefixIndex	Prefix index of the next hop for an ECMP route.
OrigNexthop	Original next hop.
RelyDepth	Recursion depth.
RealNexthop	Real next hop.
Interface	Output interface.
LocalAddr	Local interface address.
TunnelCnt	Number of tunnels after route recursion.
Vrf	VPN instance name. For the public network, this field displays default-vrf.
TunnelID	ID of the tunnel after route recursion.
Topology	Non-base topologies are not supported in the current software version. Topology name. The topology name for the IPv4 public network is base. This field is blank for IPv6, because IPv6 does not support non-base topologies.
Weight	ECMP route weight. This field displays 0 for non-ECMP routes.
Flags	Flags of the detailed next hop.
SRPolicyNID	NIB ID of the route obtained from an SR-MPLS TE policy through route recursion.
SRInterface	Output interface of the route obtained from the SR-MPLS TE policy through route recursion.
ColorWeight	Weight value of the color attribute in the SR-MPLS TE policy.
Locator	IPv6 prefix of the locator to which the SID belongs. If no locator is available, this field displays N/A.
MemberPort	Number of a member port in an aggregation group. If this attribute is not available, this field displays N/A.

‌

fib lifetime

Use fib lifetime to set the maximum lifetime for IPv4 or IPv6 routes in the FIB.

Use undo fib lifetime to restore the default.

Syntax

fib lifetime seconds

undo fib lifetime

Default

The maximum lifetime for IPv4 or IPv6 routes in the FIB is 600 seconds.

Views

RIB IPv4 address family view

RIB IPv6 address family view

Predefined user roles

network-admin

Parameters

seconds: Specifies the maximum lifetime for routes in the FIB, in the range of 0 to 6000 seconds. When this argument is set to 0, FIB entries immediately age out after a protocol or RIB process switchover.

Usage guidelines

When a protocol or RIB process switchover occurs and GR is not configured, FIB entries age out after the time specified in this command.

Examples

# Set the maximum lifetime for IPv4 routes in the FIB to 60 seconds.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] fib lifetime 60

flush route-attribute

Use flush route-attribute to enable the RIB to flush route attribute information to the FIB.

Use undo flush route-attribute remove the configuration.

Syntax

flush route-attribute protocol

undo flush route-attribute protocol

Default

The RIB does not flush route attribute information to the FIB.

Views

RIB IPv4 address family view

RIB IPv6 address family view

Predefined user roles

network-admin

Parameters

protocol: Specifies a routing protocol. In the current software version, only BGP is supported.

Examples

# Enable the RIB to flush BGP route attribute information to the FIB.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] flush route-attribute bgp

inter-protocol ecmp

Use inter-protocol ecmp to enable routes from different protocols in the RIB IPv4 or IPv6 address family to form ECMP routes.

Use undo inter-protocol ecmp to restore the default.

Syntax

inter-protocol ecmp [ ignore-preference ] [ vpn-instance vpn-instance-name ]

undo inter-protocol ecmp [ vpn-instance vpn-instance-name ]

Default

Routes from different protocols cannot form ECMP routes.

Views

RIB IPv4 address family view

RIB IPv6 address family view

Predefined user roles

network-admin

Parameters

ignore-preference: Allows routes with different preferences to form ECMP routes. If you do not specify this keyword, only routes with the same preference can form ECMP routes.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, the command enables routes from different protocols in the public network to form ECMP routes.

Usage guidelines

By default, routes from different protocols have different preferences, and the route costs are calculated in different ways. Such routes cannot form ECMP routes. Configure this command to ignore the costs for routes from different protocols, so that they can form ECMP routes.

For routes from multiple protocols with the same destination to form ECMP routes, follow these restrictions and guidelines:

· If you do not specify the ignore-preference keyword, routes with the highest priority will form ECMP routes. You can edit the preferences for routes from different protocols to the same value, so that they can form ECMP routes.

· If you specify the ignore-preference keyword, multiple routes will form ECMP routes.

If you configure both this command and the inter-protocol fast-reroute command, only this command takes effect.

Examples

# Enable routes from different protocols in the RIB IPv4 address family of the public network to form ECMP routes.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] inter-protocol ecmp

inter-protocol fast-reroute

Use inter-protocol fast-reroute to enable IPv4 or IPv6 RIB inter-protocol FRR.

Use undo inter-protocol fast-reroute to disable IPv4 or IPv6 RIB inter-protocol FRR.

Syntax

inter-protocol fast-reroute [ ecmp-shared ] [ vpn-instance vpn-instance-name ]

undo inter-protocol fast-reroute [ vpn-instance vpn-instance-name ]

Default

Inter-protocol FRR is disabled.

Views

RIB IPv4 address family view

RIB IPv6 address family view

Predefined user roles

network-admin

Parameters

ecmp-shared: Specify a shared next hop for ECMP routes. Multiple ECMP routes use the same backup next hop. If you do not specify this keyword, the device performs backup next hop calculation for only non-ECMP routes.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, the command enables IPv4 or IPv6 RIB inter-protocol FRR for the public network.

Usage guidelines

This command allows a device to perform fast rerouting between routes of different protocols. A backup next hop is automatically selected to reduce the service interruption time caused by unreachable next hops. When the next hop of the primary link fails, the traffic is redirected to the backup next hop.

This command uses the next hop of a route from a different protocol as the backup next hop for the faulty route, which might cause loops.

Inter-protocol FRR cannot select a backup next hop from routes in the RIB that have the same next hop, output interface, and destination as those of the faulty route.

If you specify the ecmp-shared keyword, the device calculates a shared backup next hop for multiple ECMP routes with the same destination. This backup next hop is from a different protocol than the ECMP routes. When all next hops of the ECMP routes fail, RIB replaces them with the backup next hop, and issues the backup next hop to the FIB as an ECMP route. You can view the detailed route information with the display ip routing-table command. The route with the Backup state in the output indicates the backup next hop. If the backup next hop is the same as a next hop of an ECMP route, RIP will not issue the backup next hop to the FIB. In this case, the backup next hop will not take effect.

If you configure both this command and the inter-protocol ecmp command, this command will not take effect.

Examples

# Enable IPv4 RIB inter-protocol FRR for the public network.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] inter-protocol fast-reroute

ipv6 route-direct track

Use ipv6 route-direct track to associate a track entry with the IPv6 direct route on an interface and apply a cost value to the IPv6 direct route after the track entry changes to Negative state.

Use undo ipv6 route-direct track to restore the default.

Syntax

ipv6 route-direct track track-entry-number degrade-cost cost-value

undo ipv6 route-direct track

Default

No track entry is associated with the IPv6 direct route on an interface.

Views

Interface view

Predefined user roles

network-admin

Parameters

track-entry-number: Specifies a track entry ID in the range of 1 to 1024.

degrade-cost cost-value: Specifies a cost value to apply to the IPv6 direct route after the track entry changes to Negative state. The value range for the cost-value argument is 1 to 4294967295.

Usage guidelines

On a network where an IPv6 VRRP group is used as the default gateway, upstream traffic is always forwarded through the master device in the IPv6 VRRP group. The corresponding downstream traffic might take a different path because the route selection is determined by the configured dynamic routing protocol. The mismatching forwarding paths might cause the traffic to be blocked by firewalls (if configured), and increase the complexity and overhead for traffic monitoring and statistics collection operations.

You can resolve the issue by configuring IPv6 direct route-Track-IPv6 VRRP collaboration. The collaboration ensures that the upstream traffic and the corresponding downstream traffic are forwarded through matching paths (both through the master device in the IPv6 VRRP group).

To configure IPv6 direct route-Track-IPv6 VRRP collaboration, perform the following tasks on each member device of the IPv6 VRRP group:

1. Create a track entry associated with the IPv6 VRRP group member device so the track entry state changes according to the status of the device in the IPv6 VRRP group.

¡ If the device state is Backup or Initialize, the track entry state changes to Negative.

¡ If the device state is Master, the track entry state changes to Positive.

¡ If the device state is Inactive or the IPv6 VRRP group does not exist, the track entry state changes to NotReady.

2. Associate the track entry with the IPv6 direct route on the interface connected to the downstream device. The cost value of the IPv6 direct route on the interface changes according to the status of the track entry.

¡ If the track entry does not exist or the track entry is in NotReady or Positive state, the cost of the IPv6 direct route changes to 0.

¡ If the track entry is in Negative state, the cost of the IPv6 direct route changes to the value configured by using the ipv6 route-direct track command.

IMPORTANT:

The IPv6 direct route that has a lower cost value is preferentially used.

3. Enable IPv6 direct route redistribution on the IPv6 VRRP group member device for the dynamic routing protocol.

For more information about associating Track with an IPv6 VRRP group, see Track configuration in High Availability Configuration Guide.

The IPv6 direct route on an interface can be associated only with one track entry. To change the track entry associated with the IPv6 direct route on an interface, you must first execute the undo ipv6 route-direct track command to remove the original association.

Examples

# Associate track entry 1 with the IPv6 direct route on Ten-GigabitEthernet 3/0/1 and apply cost 200 to the IPv6 direct route after the track entry changes to Negative state.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/0/1

[Sysname-Ten-GigabitEthernet3/0/1] ipv6 route-direct track 1 degrade-cost 200

Related commands

track vrrp ipv6 (High Availability Command Reference)

maintenance-probe enable

Use maintenance-probe enable to enable maintenance probe (MTP).

Use undo maintenance-probe enable to disable MTP.

Syntax

maintenance-probe enable

undo maintenance-probe enable

Default

MTP is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

MTP enables the device to automatically perform the following operations upon expiration of a neighbor's hold timer:

1. Ping the neighbor or trace the route to the neighbor.

2. Record the ping or tracert results.

To view fault information, use the display commands of routing protocols, for example, the display ospf troubleshooting command. To view detailed MTP information, use the display logbuffer command.

Examples

# Enable MTP.

<Sysname> system-view

[Sysname] maintenance-probe enable

Related commands

display bgp troubleshooting

display logbuffer (Network Management and Monitoring Command Reference)

display ospf troubleshooting

nexthop recursive-lookup restrain

Use nexthop recursive-lookup restrain to configure route recursion suppression.

Use undo nexthop recursive-lookup restrain to restore the default.

Syntax

nexthop recursive-lookup restrain { maximum-interval [ minimum-interval [ incremental-interval ] ] | millisecond interval }

undo nexthop recursive-lookup restrain

Default

Route recursion suppression is disabled.

Views

RIB IPv4 address family view

RIB IPv6 address family view

Predefined user roles

network-admin

Parameters

maximum-interval: Specifies the maximum suppression timer in the range of 1 to 60 seconds.

minimum-interval: Specifies the minimum suppression timer in the range of 10 to 60000 milliseconds. The default value is 50.

incremental-interval: Specifies the incremental timer in the range of 10 to 60000 milliseconds. The default value is 200.

millisecond interval: Specifies a fixed suppression timer in the range of 10 to 10000 milliseconds.

Usage guidelines

A change of a related route or tunnel obtained through nexthop recursion triggers another recursion for the recursive route. When the network changes frequently, the route recursion is performed repeatedly, which causes high CPU usage. To solve this issue, use this command for the RIB to wait for the suppression timer to expire before obtaining the recursion result. In this way, the route recursion is performed less often and the CPU usage can be reduced. However, this command can result in lower route recursion efficiency and slow route convergence. Use this command as needed make sure the parameters are appropriate.

After you use this command, no matter how the route recursion results change within the suppression timer, the RIB always obtains the most recent results after the suppression timer expires.

To dynamically suppress route recursion, configure at least the maximum suppression timer. If the route recursion results keep changing, the suppression time increases until the maximum suppression timer expires or the recursion results stop changing.

The dynamic suppression time (T) is calculated based on the number of route recursions (N), as follows:

· When N = 1, T = minimum-interval.

· When N ≥ 2, T = minimum-interval + incremental-interval × [ 2 ^ ( N - 2 ) ], and T ≤ maximum-interval.

· When T reaches maximum-interval for three consecutive times, T = minimum-interval in the next recursion, and N becomes 1.

· If the recursion results have not changed in two times the maximum-interval, T = minimum-interval in the next recursion, and N becomes 1.

The value for the minimum-interval or incremental-interval argument cannot be greater than that for the maximum-interval argument.

The suppression timer settings apply to only the next route recursion.

If you execute this command multiple times, the most recent configuration takes effect.

The actual suppression timer equals the sum of the suppression timer configured in this command and the timer configured in any of the following commands:

· nexthop recursive-lookup restrain (BGP instance view/BGP-VPN instance view)

· nexthop recursive-lookup delay (BGP address family view)

Examples

# Set the maximum suppression timer, minimum suppression timer, and incremental timer for IPv4 route recursion to 60 seconds, 500 milliseconds, and 1000 milliseconds, respectively.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] nexthop recursive-lookup restrain 60 500 1000

# Set the fixed suppression timer for IPv6 route recursion to 1000 milliseconds.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv6

[Sysname-rib-ipv6] nexthop recursive-lookup restrain millisecond 1000

Related commands

nexthop recursive-lookup delay

nexthop recursive-lookup restrain

nexthop recursive-lookup restrain clear-interval

Use nexthop recursive-lookup restrain clear-interval to set the interval for clearing the recursion loop counter.

Use undo nexthop recursive-lookup restrain clear-interval to restore the default.

Syntax

nexthop recursive-lookup restrain clear-interval interval

undo nexthop recursive-lookup restrain clear-interval

Default

The interval for clearing the recursion loop counter is 600 seconds.

Views

RIB IPv4 address family view

RIB IPv6 address family view

Predefined user roles

network-admin

Parameters

clear-interval interval: Specifies the interval for clearing the recursion loop counter, in the range of 1 to 65535 seconds.

Usage guidelines

Recursion loop suppression enables the system to use a counter to record the number of route recursion failures. When the counter reaches 20, the system suppresses route recursion for a specified period of time. When the suppression time expires, the system resets the counter and disables route recursion suppression.

Examples

# Set the interval for clearing the recursion loop counter to 100 seconds.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] nexthop recursive-lookup restrain clear-interval 100

nexthop recursive-lookup restrain disable

Use nexthop recursive-lookup restrain disable to disable the suppression for next hop recursion loop.

Use undo nexthop recursive-lookup restrain disable to enable the suppression for next hop recursion loop.

Syntax

nexthop recursive-lookup restrain disable

undo nexthop recursive-lookup restrain disable

Default

Suppression for next hop recursion loop is enabled.

Views

RIB IPv4 address family view

RIB IPv6 address family view

Predefined user roles

network-admin

Usage guidelines

A recursion loop occurs when a route recurses to a related route that recurses back to the route. It causes a route recursion failure and further lookup for a related route. If recursion loop persists, continuous route flapping will cause high system resource consumption and CPU utilization.

This command enables the system to use a counter to record the number of route recursion failures. When the counter reaches 20, the system suppresses route recursion for a specified period of time to save system resources on the device.

Examples

# Disable the suppression for next hop recursion loop.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] nexthop recursive-lookup restrain disable

primary-path-detect bfd

Use primary-path-detect bfd to use BFD to detect the next hop availability of the primary route for inter-protocol FRR or ECMP routes.

Use undo primary-path-detect bfd to cancel the configuration that uses BFD to detect the next hop availability of the primary route for inter-protocol FRR or ECMP routes.

Syntax

primary-path-detect bfd { ctrl | echo } [ inter-protocol-frr | protocol-ecmp protocol ]

undo primary-path-detect bfd [ inter-protocol-frr | protocol-ecmp protocol ]

Default

BFD is not used for detecting the next hop availability of the primary route for inter-protocol FRR or ECMP routes.

Views

RIB IPv4 address family view

RIB IPv6 address family view

Predefined user roles

network-admin

Parameters

ctrl: Specifies the BFD control packet mode.

echo: Specifies the BFD echo packet mode.

inter-protocol-frr: Detects the next hop availability of the primary route for inter-protocol FRR.

protocol-ecmp protocol: Detects the next hop availability of the primary route for ECMP routes of a routing protocol.

· In RIB IPv4 address family view, the value for the protocol argument can be bgp, isis, ospf, or static.

· In RIB IPv6 address family view, the value for the protocol argument depends on the BFD mode.

¡ In BFD control packet mode, the value can be bgp4+, isisv6, ospfv3, or static.

¡ In BFD echo packet mode, the value can be bgp4+ or static.

Usage guidelines

This command enables the device to automatically create an IPFRR type of BFD session. The device uses this BFD session to detect the next hop availability of the primary route to speed traffic switchover when the next hop of the primary route fails.

· For inter-protocol FRR, the primary route is the route with the highest preference among the routes to the same destination.

· For ECMP routes of a routing protocol, the primary route is each ECMP route. If you specify the ecmp-shared keyword when configuring FRR for a routing protocol, the device will use the LFA algorithm to calculate backup next hops for each ECMP route. The routes destined for the backup next hops are also added to the routing table as ECMP routes and the state of these routes is backup. BFD does not detect these backup ECMP routes.

This command can take effect and automatically establish the IPFRR type of BFD session only when a primary route exists and the primary route has backup next hops.

You can execute this command multiple times to change the BFD mode (echo packet mode or control packet mode).

If you do not specify the inter-protocol-frr or protocol-ecmp keyword, the command applies to both inter-protocol FRR and ECMP routes. The command without the inter-protocol-frr and protocol-ecmp keywords takes precedence over that with the inter-protocol-frr or protocol-ecmp keyword. For example, if you have used the primary-path-detect bfd ctrl command, you can use only the following commands to modify or cancel the command configuration:

· primary-path-detect bfd echo.

· undo primary-path-detect bfd.

When you use a BFD session in control packet mode to detect the next hop availability of the primary route, you must manually create a static BFD session on the next hop device. The reason is that the BFD session in control packet mode requires negotiation of both ends for successful establishment. The local device can use the BFD session in control packet mode to detect the next hop availability of the primary route only when the static BFD session created on the next hop device of the primary route meets the following requirements:

· The static BFD session is a single-hop BFD session in control packet mode.

· The source IP address of the static BFD session is the destination IP address of the local automatically created BFD session.

· The destination IP address of the static BFD session is the source IP address of the local automatically created BFD session.

· The remote discriminator of the static BFD session is the local discriminator of the local automatically created BFD session.

For more information about static BFD session creation, see BFD configuration in High Availability Configuration Guide.

When service modules other than RIB, for example, BGP, OSPF, or IS-IS, use BFD to detect the next hop availability of the primary route, they also automatically create a BFD session. If the BFD session automatically created by these service modules detects the availability of the same next hop as RIB, the device does not automatically create the same type of BFD session for RIB. Instead, RIB will use the existing BFD session.

Examples

# Use BFD in control packet mode to detect the next hop availability of the primary route for IS-IS ECMP routes.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] primary-path-detect bfd ctrl protocol-ecmp isis

Related commands

display ip routing-table

fast-reroute

inter-protocol fast-reroute

protocol lifetime

Use protocol lifetime to set the maximum lifetime for IPv4 or IPv6 routes and labels in the RIB.

Use undo protocol lifetime to restore the default.

Syntax

protocol protocol [ instance instance-name ] lifetime seconds

undo protocol protocol [ instance instance-name ] lifetime

Default

The maximum lifetime for IPv4 or IPv6 routes and labels in the RIB is 900 seconds.

Views

RIB IPv4 address family view

RIB IPv6 address family view

Predefined user roles

network-admin

Parameters

protocol: Specifies a routing protocol.

instance instance-name: Specifies a BGP instance by its name, a case-sensitive string of 1 to 31 characters. This argument applies only to the BGP protocol. If you do not specify a BGP instance, this command sets the maximum lifetime for all BGP routes and labels in the RIB.

seconds: Specifies the maximum lifetime for routes and labels in the RIB, in the range of 1 to 6000 seconds.

Usage guidelines

When GR is enabled, make sure the protocol can complete GR and install all route entries to the RIB within the lifetime configured in this command.

Examples

# Set the maximum lifetime for RIP routes and labels in the RIB to 60 seconds.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] protocol rip lifetime 60

protocol nexthop recursive-lookup

Use protocol nexthop recursive-lookup to configure routing policy-based recursive lookup.

Use undo protocol nexthop recursive-lookup to remove the configuration.

Syntax

protocol protocol nexthop recursive-lookup route-policy route-policy-name

undo protocol protocol nexthop recursive-lookup route-policy

Default

Routing policy-based recursive lookup is not configured.

Views

RIB IPv4 address family view

RIB IPv6 address family view

Predefined user roles

network-admin

Parameters

protocol: Specifies a routing protocol, which can be bgp or static in RIB IPv4 address family view or bgp4+ in RIB IPv6 address family view.

route-policy-name: Specifies a routing policy by its name, a case-sensitive string of 1 to 63 characters.

Usage guidelines

Configure routing policy-based recursive lookup to control route recursion results. For example, when a route changes, the routing protocol has to perform a route recursion if the next hop is indirectly connected. The routing protocol might select an incorrect path, which can cause traffic loss. To prevent this problem, you can use a routing policy to filter out incorrect routes. The routes that pass the filtering of the routing policy will be used for route recursion.

The apply clauses in the specified routing policy cannot take effect.

Make sure a minimum of one related route can match the routing policy for correct traffic forwarding.

The routing policy does not apply to routes received from directly connected BGP neighbors.

Examples

# Configure recursive lookup based on routing policy policy1 for BGP routes.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] protocol bgp nexthop recursive-lookup route-policy policy1

record-limit

Use record-limit to set the maximum number of RIB next hop records or route entry records.

Use undo record-limit to restore the default.

Syntax

record-limit limit [ rib nib [ flush [ delete | update ] | receive [ add | delete | update ] ] ]

undo record-limit [ rib nib [ flush [ delete | update ] | receive [ add | delete | update ] ] ]

Default

The maximum number of RIB next hop records or route entry records is 1000.

Views

RIB IPv4 address family view

RIB IPv6 address family view

Predefined user roles

network-admin

Parameters

limit: Sets the maximum number of RIB next hop records or route entry records. The value range is 0 to 10000. To disable recording for RIB next hops or route entries, set the value to 0. When the number of records reaches the maximum number, the system can record new next hops or route entries. However, the new next hop or route entry records overwrite the oldest next hop or route entry records.

rib nib: Sets the maximum number of RIB next hop records.

routing-table: Sets the maximum number of route entry records.

flush: Sets the maximum number of records flushed from RIB to FIB.

notify: Sets the maximum number of records reported by RIB to routing protocols.

receive: Sets the maximum number of records received by RIB from routing protocols.

add: Sets the maximum number of records that contain the add action.

update: Sets the maximum number of records that contain the update action. If you specify the flush or notify keyword, records that contain the add action are also counted into the update category.

delete: Sets the maximum number of records that contain the delete action.

Usage guidelines

Repeat the command to set the maximum number for different types of records.

If you do not specify the rib nib or routing-table keywords, the command sets the maximum number for all types of RIB next hop and route entry records.

If you do not specify the add, delete, or update keyword, the command sets the maximum number for records that contain the add, delete, and update actions.

Examples

# Set the maximum number of next hop records and route entry records to 100 in the IPv4 RIB.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] record-limit 100

# Set the maximum number of IPv4 route entry records to 200.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] record-limit 200 routing-table

# Set the maximum number of next hop records that contain the add action to 300. The records are received by IPv4 RIB from routing protocols.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] record-limit 300 rib nib receive

# Set the maximum number of route entry records that contain the update action to 400. The records are reported by IPv6 RIB to routing protocols.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv6

[Sysname-rib-ipv6] record-limit 400 routing-table notify update

# Set the maximum number of next hop records that contain the delete action to 500. The records are flushed from IPv6 RIB to FIB.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv6

[Sysname-rib-ipv6] record-limit 500 rib nib flush delete

reset ip routing-table record

Use reset ip routing-table record to clear IPv4 routing entry records.

Syntax

reset ip routing-table record

Views

User view

Predefined user roles

network-admin

Examples

# Clear IPv4 routing entry records.

<Sysname> reset ip routing-table record

reset ip routing-table statistics protocol

Use reset ip routing-table statistics protocol to clear IPv4 route statistics.

Syntax

reset ip routing-table statistics protocol [ vpn-instance vpn-instance-name ] { protocol | all }

reset ip routing-table [ all-routes | all-vpn-instance ] statistics protocol { protocol | all }

Views

User view

Predefined user roles

network-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters.

all-routes: Clears route statistics for the public network and all VPN instances.

all-vpn-instance: Clears route statistics for all VPN instances.

protocol: Clears route statistics for a routing protocol.

all: Clears route statistics for all IPv4 routing protocols.

Usage guidelines

This command clears IPv4 route statistics for the public network if you do not specify the all-routes, vpn-instance, or all-vpn-instance keyword.

Examples

# Clear all IPv4 route statistics for the public network.

<Sysname> reset ip routing-table statistics protocol all

reset ipv6 rib nib record

Use reset ipv6 rib nib record to clear next hop records in the IPv6 RIB.

Syntax

reset ipv6 rib nib record

Views

User view

Predefined user roles

network-admin

Examples

# Clear next hop records in the IPv6 RIB.

<Sysname> reset ipv6 rib nib record

reset ipv6 routing-table record

Use reset ipv6 routing-table record to clear IPv6 routing entry records.

Syntax

reset ipv6 routing-table record

Views

User view

Predefined user roles

network-admin

Examples

# Clear IPv6 routing entry records.

<Sysname> reset ipv6 routing-table record

reset ipv6 routing-table statistics protocol

Use reset ipv6 routing-table statistics protocol to clear IPv6 route statistics.

Syntax

reset ipv6 routing-table statistics protocol [ vpn-instance vpn-instance-name ] { protocol | all }

reset ipv6 routing-table [ all-routes | all-vpn-instance ] statistics protocol { protocol | all }

Views

User view

Predefined user roles

network-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters.

all-routes: Clears route statistics for the public network and all VPN instances.

all-vpn-instance: Clears route statistics for all VPN instances.

protocol: Clears route statistics for an IPv6 routing protocol.

all: Clears route statistics for all IPv6 routing protocols.

Usage guidelines

This command clears IPv6 route statistics for the public network if you do not specify the all-routes, vpn-instance, or all-vpn-instance keyword.

Examples

# Clear all IPv6 route statistics for the public network.

<Sysname> reset ipv6 routing-table statistics protocol all

reset rib nib record

Use reset rib nib record to clear next hop records in the IPv4 RIB.

Syntax

reset rib nib record

Views

User view

Predefined user roles

network-admin

Examples

# Clear next hop records in the IPv4 RIB.

<Sysname> reset rib nib record

rib

Use rib to enter RIB view.

Use undo rib to remove all configurations in RIB view.

Syntax

rib

undo rib

Views

System view

Predefined user roles

network-admin

Examples

# Enter RIB view.

<Sysname> system-view

[Sysname] rib

[Sysname-rib]

route-direct track

Use route-direct track to associate a track entry with the IPv4 direct route on an interface and apply a cost value to the IPv4 direct route after the track entry changes to Negative state.

Use undo route-direct track to restore the default.

Syntax

route-direct track track-entry-number degrade-cost cost-value

undo route-direct track

Default

No track entry is associated with the IPv4 direct route on an interface.

Views

Interface view

Predefined user roles

network-admin

Parameters

track-entry-number: Specifies a track entry ID in the range of 1 to 1024.

degrade-cost cost-value: Specifies a cost value to apply to the IPv4 direct route after the track entry changes to Negative state. The value range for the cost-value argument is 1 to 4294967295.

Usage guidelines

On a network where an IPv4 VRRP group is used as the default gateway, upstream traffic is always forwarded through the master device in the IPv4 VRRP group. The corresponding downstream traffic might take a different path because the route selection is determined by the configured dynamic routing protocol. The mismatching forwarding paths might cause the traffic to be blocked by firewalls (if configured), and increase the complexity and overhead for traffic monitoring and statistics collection operations.

You can resolve the issue by configuring IPv4 direct route-Track-IPv4 VRRP collaboration. The collaboration ensures that the upstream traffic and the corresponding downstream traffic are forwarded through matching paths (both through the master device in the IPv4 VRRP group).

To configure IPv4 direct route-Track-IPv4 VRRP collaboration, perform the following tasks on each member device of the IPv4 VRRP group:

1. Create a track entry associated with the IPv4 VRRP group member device so the track entry state changes according to the status of the device in the IPv4 VRRP group.

¡ If the device state is Backup or Initialize, the track entry state changes to Negative.

¡ If the device state is Master, the track entry state changes to Positive.

¡ If the device state is Inactive or the IPv4 VRRP group does not exist, the track entry state changes to NotReady.

2. Associate the track entry with the IPv4 direct route on the interface connected to the downstream device. The cost value of the IPv4 direct route on the interface changes according to the status of the track entry.

¡ If the track entry does not exist or the track entry is in NotReady or Positive state, the cost of the IPv4 direct route changes to 0.

¡ If the track entry is in Negative state, the cost of the IPv4 direct route changes to the value configured by using the route-direct track command.

IMPORTANT:

The IPv4 direct route that has a lower cost value is preferentially used.

3. Enable IPv4 direct route redistribution on the IPv4 VRRP group member device for the dynamic routing protocol.

The IPv4 direct route on an interface can be associated only with one track entry. To change the track entry associated with the IPv4 direct route on an interface, you must first execute the undo route-direct track command to remove the original association.

Examples

# Associate track entry 1 with the IPv4 direct route on Ten-GigabitEthernet 3/0/1 and apply cost 200 to the IPv4 direct route after the track entry changes to Negative state.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/0/1

[Sysname-Ten-GigabitEthernet3/0/1] route-direct track 1 degrade-cost 200

Related commands

track vrrp (High Availability Command Reference)

routing-table limit

Use routing-table limit to set the maximum number of active IPv4/IPv6 routes supported by the device.

Use undo routing-table limit to restore the default.

Syntax

routing-table limit number simply-alert

undo routing-table limit

Default

The maximum number of active IPv4/IPv6 routes is not set for the device.

Views

RIB IPv4 address family view

RIB IPv6 address family view

Predefined user roles

network-admin

Parameters

number: Specifies the maximum number of active IPv4/IPv6 routes supported by the device, in the range of 1 to 4294967295.

simply-alert: Enables the device to still accept active routes but generate a log message when the number of active IPv4/IPv6 routes exceeds the maximum number.

Usage guidelines

Configuration in RIB IPv4 address family view limits the number of active IPv4 routes for the public network and all VPN instances.

Configuration in RIB IPv6 address family view limits the number of active IPv6 routes for the public network and all VPN instances.

Examples

# In RIB IPv4 address family view, set the maximum number of active IPv4 routes to 1000 for the public network and all VPN instances. The device still accepts new active routes but generates a system log message when the maximum number of active routes is exceeded.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] routing-table limit 1000 simply-alert

snmp-agent trap enable ipv6 rib

Use snmp-agent trap enable ipv6 rib to enable SNMP notifications for IPv6 RIB.

Use undo snmp-agent trap enable ipv6 rib to disable SNMP notifications for IPv6 RIB.

Syntax

snmp-agent trap enable ipv6 rib

undo snmp-agent trap enable ipv6 rib

Default

SNMP notifications are enabled for IPv6 RIB.

Views

System view

Predefined user roles

network-admin

Usage guidelines

After you enable this feature, IPv6 RIB can generate notifications and send them to the SNMP module. For the IPv6 RIB notifications to be sent correctly, you must also configure SNMP on the device. For more information about configuring SNMP, see the network management and monitoring configuration guide for the device.

Examples

# Disable SNMP notifications for IPv6 RIB.

<Sysname> system-view

[Sysname] undo snmp-agent trap enable ipv6 rib

06-Layer 3—IP Routing Command Reference

display ip routing-table acl

display ip routing-table ip-address

display ip routing-table prefix-list

display ip routing-table summary

display ipv6 routing-table acl

display ipv6 routing-table ipv6-address

nexthop recursive-lookup restrain clear-interval

reset ipv6 routing-table statistics protocol

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

Company Information

News & Events

Contact Us