Contents

QinQ commands· 1

display qinq· 1

qinq enable· 2

qinq ethernet-type (interface view) 2

 

QinQ commands

In this document:

·     Customer network VLANs (CVLANs), also called inner VLANs, refer to VLANs that a customer uses on the private network.

·     Service provider network VLANs (SVLANs), also called outer VLANs, refer to VLANs that a service provider uses to transmit VLAN tagged traffic for customers.

display qinq

Use display qinq to display QinQ-enabled interfaces.

Syntax

display qinq [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays all QinQ-enabled interfaces.

Usage guidelines

If QinQ is not enabled on any interfaces, this command does not provide any output.

Examples

# Enable QinQ on Ten-GigabitEthernet 3/1/1. Then, verify that QinQ is enabled on the interface.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/1/1

[Sysname-Ten-GigabitEthernet3/1/1] qinq enable

[Sysname-Ten-GigabitEthernet3/1/1] display qinq interface ten-gigabitethernet 3/1/1

Interface

 Ten-GigabitEthernet3/1/1

# Enable QinQ on Ten-GigabitEthernet 3/1/1 and Ten-GigabitEthernet 3/1/3. Then, verify that QinQ is enabled on the interfaces.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/1/1

[Sysname-Ten-GigabitEthernet3/1/1] qinq enable

[Sysname-Ten-GigabitEthernet3/1/1] quit

[Sysname] interface ten-gigabitethernet 3/1/3

[Sysname-Ten-GigabitEthernet3/1/3] qinq enable

[Sysname-Ten-GigabitEthernet3/1/3] display qinq

Interface

 Ten-GigabitEthernet3/1/1

 Ten-GigabitEthernet3/1/3

Related commands

qinq enable

qinq enable

Use qinq enable to enable QinQ on an interface.

Use undo qinq enable to disable QinQ on an interface.

Syntax

qinq enable

undo qinq enable

Default

QinQ is disabled on interfaces.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

You can enable QinQ on a port only when its link type is access. If the link type of the port is hybrid or trunk, you cannot enable QinQ on the port.

Examples

# Enable QinQ on Ten-GigabitEthernet 3/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/1/1

[Sysname-Ten-GigabitEthernet3/1/1] port link-type access

[Sysname-Ten-GigabitEthernet3/1/1] qinq enable

Related commands

display qinq

qinq ethernet-type (interface view)

Use qinq ethernet-type to set the TPID value in SVLAN tags on an interface.

Use undo qinq ethernet-type to restore the default TPID value in SVLAN tags on an interface.

Syntax

qinq ethernet-type service-tag hex-value

undo qinq ethernet-type service-tag

Default

The TPID value in SVLAN tags is 8100 in hexadecimal notation.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

service-tag: Sets the TPID value in the SVLAN tag.

hex-value: Sets a hexadecimal TPID value in the range of 1 to ffff, excluding the reserved EtherType values listed in Table 1.

Table 1 Reserved EtherType values

Protocol type	Value
ARP	0x0806
PUP	0x0200
RARP	0x8035
IP	0x0800
IPv6	0x86dd
PPPoE	0x8863/0x8864
MPLS	0x8847/0x8848
IPX/SPX	0x8137
IS-IS	0x8000
LACP	0x8809
LLDP	0x88cc
802.1X	0x888e
802.1ag	0x8902
Cluster	0x88a7
Reserved	0xfffd/0xfffe/0xffff

 

Examples

# Set the TPID value in the SVLAN tags to 9100 (hexadecimal) on Ten-GigabitEthernet 3/1/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 3/1/1

[Sysname-Ten-GigabitEthernet3/1/1] qinq ethernet-type service-tag 9100